Hazardous substances in construction · learning reader
Free training · Approx. 2h 30m–3h 20m · estimated self-paced learning, including activities and assessment.
Public teaching is free without an account. A free learner account is required for confirmed LMS assessment, completion and certificate records. See the full course outline and access routes.
Teaching and applied cases for accessible study. The interactive course records assessed completion.
Lesson 1
Map the substance to the task
Assess substances used or generated across the whole task, including other people and secondary handling.
The product name is only the beginning
At Mill Lane, the same room may contain unopened bags, wet mixes, generated dust, coating mist, solvent vapour and old paint debris. These are different exposure situations even when the materials appear on one delivery list. Start with the exact activity, the form of the substance, how people may contact it and the conditions that influence exposure.
Include substances generated by the work, not only purchased products. Sanding, heating, cutting and disturbing old materials can produce harmful contaminants without a supplier delivering a labelled container of that contaminant. The assessment should reach setup, use, cleaning, maintenance, waste handling and other people affected nearby.
Separate hazard from the exposure decision. A substance may have harmful properties, while the task determines who encounters it, by which route, how much and for how long. That distinction helps select controls that interrupt exposure rather than relying on a warning label or a general instruction to be careful.
Visual practice · Map the substance to the task
SHAREhub photographic illustration · Local extraction and chemical containers at a workplace assessment station. Use the written case for the exercise; this image does not prove a defect or safe system.The product name is only the beginning
At Mill Lane, the same room may contain unopened bags, wet mixes, generated dust, coating mist, solvent vapour and old paint debris. These are different exposure situations even when the materials appear on one delivery list. Start with the exact activity, the form of the substance, how people may contact it and the conditions that influence exposure.
Which hazardous substances should be included in the assessment?
The assessment should include purchased products, process-generated contaminants, residues, waste, biological agents and substances brought onto site by contractors. Many weak assessments only list labelled containers. That misses some of the most important occupational health risks: respirable crystalline silica from cutting stone, wood dust from sanding, welding fume from hot work, flour dust in bakeries, diesel exhaust in enclosed yards, metalworking fluid mist, cleaning residues, contaminated filters and biological agents in healthcare, waste, leisure and maintenance work.
What forms can hazardous substances take?
Hazardous substances can appear as gases, vapours, fumes, mists, aerosols, dusts, powders, liquids, pastes, solids, fibres and biological agents. The physical form changes the exposure route and the control method. A volatile solvent may create an inhalation and fire risk.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Which hazardous substances should be included in the assessment?
The assessment should include purchased products, process-generated contaminants, residues, waste, biological agents and substances brought onto site by contractors.
Many weak assessments only list labelled containers. That misses some of the most important occupational health risks: respirable crystalline silica from cutting stone, wood dust from sanding, welding fume from hot work, flour dust in bakeries, diesel exhaust in enclosed yards, metalworking fluid mist, cleaning residues, contaminated filters and biological agents in healthcare, waste, leisure and maintenance work.
The physical form changes the exposure route. A solid block may be low risk during storage but high risk when cut into respirable dust. A liquid may be low volatility at room temperature but generate vapour when heated. A powder may become airborne during tipping, weighing or cleaning. An aerosol can create fine droplets that travel beyond the immediate task.
Contractors can introduce substances that affect host workers, and host premises can expose contractors to residues or process contaminants. The assessment should therefore include interfaces, simultaneous operations and shared areas.
Hazardous substance forms to assess - Hazardous substance forms to assess
Hazardous substances can appear as gases, vapours, fumes, mists, aerosols, dusts, powders, liquids, pastes, solids, fibres and biological agents.
The physical form changes the exposure route and the control method. A volatile solvent may create an inhalation and fire risk. A corrosive liquid may create splash and skin-burn risks. A fine powder may become airborne during pouring or mixing. A hot process may create fume even if the original material seemed stable.
Chemicals can also change form during use. Spraying turns liquids into aerosols. Heating can produce vapours or decomposition products. Grinding, cutting or sanding can turn solid materials into respirable dust. Mixing incompatible substances can create heat, gas, pressure or toxic release.
The COSHH assessment should name the form present during the task, not just the product name. This is often where weak assessments fail.
Chemical forms and typical concerns
Form
Examples
Main concern
Gas
Chlorine, ammonia, carbon dioxide, nitrogen.
Inhalation, asphyxiation, toxicity, pressure or release.
Vapour
Solvent vapour from paints, thinners or fuels.
Inhalation, flammability and nervous-system effects.
Fume
Welding fume, thermal decomposition products.
Fine particles and metal oxide exposure.
Mist or aerosol
Spraying, machining fluids, disinfectant fogging.
Inhalation and skin or eye deposition.
Dust or powder
Silica, flour, cement, powders and pigments.
Respirable dust, skin contact and combustible dust where relevant.
Liquid or paste
Acids, alkalis, resins, adhesives and coatings.
Skin absorption, burns, dermatitis, splash and fire risk.
Solid article or residue
Contaminated filters, rags, deposits or absorbents.
Secondary exposure during cleaning, storage or disposal.
Apply the learning
The chemical register lists the coating and cement bags but omits dust generated by removing the old finish.
Decision and explanation
Include generated contaminants and the complete work sequence in the task-specific assessment.
Assess substances used or generated across the whole task, including other people and secondary handling.
Lesson 2
Use labels and safety data intelligently
Chemical hazard pictograms · examples and checksOptional reference · all nine symbols · does not change assessment requirements
READ THE LABEL · UNDERSTAND THE TASK
Recognise the symbol. Read the full label. Assess the actual task.
Examples illustrate possible uses of a symbol, not the classification of every formulation. A product can carry several pictograms. Check its current label, hazard statements and matching safety data sheet (SDS).
Construction: supplied products and process-generated dust or fume need task-specific assessment.
CLP/GHS hazard pictograms: meanings and illustrative examples
Pictogram and hazard
What it can mean
Example and question before work
ExplosiveGHS01
Explosion, blast or projection hazards; also certain self-reactive substances and organic peroxides.
Example: Certain fireworks or reactive chemical products.Ask: Does the authorised task account for impact, heat and the product’s stability limits?
FlammableGHS02
Can ignite; also used for certain self-heating, pyrophoric or water-reactive hazards.
Example: Petrol or some solvent-based products.Ask: What could release vapour or ignite it during this task, including nearby work?
OxidisingGHS03
Can cause or intensify fire; some strong oxidisers present an explosion hazard.
Example: Oxygen or certain oxidising chemicals.Ask: What incompatible materials and contamination must the assessed storage and connection keep apart?
Gas under pressureGHS04
Pressurised gas may burst if heated; refrigerated gas can cause cold burns.
Example: Compressed-gas cylinders.Ask: Have the gas identity, cylinder, connection and pressure or temperature hazards been checked?
CorrosiveGHS05
May damage metals, cause severe skin burns or cause serious eye damage; read the stated hazard.
Example: Certain drain cleaners, acids or alkalis.Ask: Which contact and splash routes must be prevented in this actual handling or dilution task?
Acute toxicityGHS06
Can be toxic or fatal after short exposure through the stated route.
Example: Methanol or certain pesticide products.Ask: Which exposure routes and emergency arrangements does this product’s information identify?
Harmful / irritantGHS07
May indicate harmful acute toxicity, irritation, skin sensitisation, drowsiness or dizziness; also ozone-layer hazards.
Example: Some detergents or cleaning products.Ask: What do the hazard statements say? Do not dismiss this as a harmless or mild product.
Serious health hazardGHS08
Can indicate cancer, genetic or reproductive harm, organ damage, respiratory sensitisation or aspiration hazard.
Example: Petrol or some sensitising chemical products.Ask: Which particular health effect is stated, and how does the task prevent the relevant exposure?
Hazardous to the environmentGHS09
Hazardous to aquatic life, potentially with long-lasting effects.
Example: Certain pesticides, biocides or fuels.Ask: How will the assessed arrangements prevent release to drains, water or soil?
Read beyond the picture · Open a prompt to compare the explanation.
Is the exclamation mark the same as the chest-starburst symbol?
No. The two symbols communicate different groups of hazards. Read the actual hazard statements: skin sensitisation and respiratory sensitisation are not interchangeable, and neither symbol specifies the complete task controls.
Does a bottle with no pictogram prove the task is safe?
No. Work may generate hazardous dust, fume or mist, and exposure depends on the task. Resolve missing or conflicting identification before use. A pictogram is not a compatibility chart or a complete workplace risk assessment.
Which information turns recognition into a useful work decision?
Match the product and SDS revision. Read the hazard statements and relevant SDS sections for handling, storage, exposure control, emergencies and reactivity together. Then check the actual task assessment and controls. A safety data sheet is not itself a COSHH assessment.
Fisher Scientific UK · BP2618 range · CAS 67-63-0 Revision 19 · 13 October 2023
This learning example refers to the identified supplier edition. It is not a replacement SDS or confirmation that this is the latest sheet for a product you hold. Obtain the current matching supplier SDS before real use.
Below is SHARE’s learning annotation, not a rebranded supplier document or a complete safety data sheet.
Identity
Propan-2-ol / isopropanol; the referenced sheet identifies a laboratory-grade product.
Section 2 signals
Danger; flame and exclamation-mark pictograms. H225, H319 and H336 identify flammability, eye irritation and possible drowsiness/dizziness.
Section 3 composition
The referenced sheet lists isopropyl alcohol above 95% by weight.
Section 8 decision
Engineering measures and several glove-material options appear. Check the complete conditions; no single glove or respirator is selected by this lesson.
Section 9 example
A 12°C closed-cup flash point is listed. This is product data, not a workplace exposure reading or an automatic safe-temperature limit.
Explore every section
1. Identification
Match the product, supplier, intended use and emergency contact to the actual container. A familiar chemical name alone may not identify a formulation.
2. Hazards identification
Read classification, pictograms, signal word and hazard/precautionary statements together. Identify the routes and outcomes the task must prevent.
3. Composition / ingredients
Check concentration and relevant ingredients. A diluted mixture, hardener or changed formulation may need different information and assessment.
4. First-aid measures
Prepare product-specific first-aid arrangements and ready access to the full sheet. Do not replace the workplace emergency procedure with a memory exercise.
5. Firefighting measures
Provide the relevant information to the site fire-planning route. An SDS does not authorise an untrained worker to fight a chemical fire.
6. Accidental release
Plan who raises the alarm, isolates the area and deals with a spill within their training. Confirm available equipment and the boundary for specialist help.
7. Handling and storage
Translate the supplier conditions into the actual transfer, storage, access and housekeeping method. Consider other work and incompatible neighbours.
8. Exposure controls / PPE
Read exposure limits, engineering controls and residual PPE together. Check jurisdiction, units and averaging period. Verify control performance and exact glove/RPE suitability.
9. Physical / chemical properties
Consider volatility, flash point, state and other relevant properties at the actual temperature and method. Odour is not a reliable exposure measurement.
10. Stability / reactivity
Identify incompatible materials, conditions to avoid and possible decomposition. Check the whole process and waste stream, not just separate containers.
11. Toxicological information
Connect the health effects to possible inhalation, skin, eye and ingestion exposure. Use competent advice where specialist interpretation is needed.
12. Ecological information
Plan to prevent environmental release, including drains and water. Lack of a fish/tree symbol does not grant permission to discharge.
13. Disposal considerations
Specify the responsible waste route for the product, contaminated materials and containers. Do not assume evaporation or dilution is an acceptable disposal method.
14. Transport information
Check transport classification through the relevant competent route. Supply pictograms and transport labels have different functions.
15. Regulatory information
Identify relevant restrictions and market scope, then check workplace duties separately. A regulatory entry is not a completed COSHH assessment.
16. Other information
Check revision history, abbreviations and supporting statements. Trace material changes into the assessment, instructions, storage and briefing.
Worked COSHH application · fictional laboratory proposal
Define the proposed use
Fictional laboratory task: wipe small parts for 10 minutes twice per shift, using a proposed 50mL working quantity at ambient temperature. Record the exact product, method, location, people and frequency. These are exercise assumptions, not authorised operating limits.
Find the exposure and application differences
Compare a controlled dispensing/wiping proposal with spraying the same liquid over an open surface near other work. Spray, surface area, ventilation, duration, splashes and nearby people change the assessment even though the SDS is unchanged. Confirm the proposed use is suitable.
Work through the control hierarchy
First ask whether the task can avoid the chemical or use a verified safer method. If it remains necessary, assess release prevention, suitable dispensing, enclosure or ventilation before residual PPE. Do not invent a dilution or declare a small quantity safe.
Specify and verify the real controls
Use sections 7–10 together with competent task assessment. Identify ventilation performance, compatible equipment and the exact glove selection/breakthrough evidence for the job. Consider fire and explosion controls alongside health exposure. Do not copy a generic PPE line and call the work controlled.
Plan the whole job
Include setup, transfer, use, cleaning, storage, waste, maintenance and foreseeable upset. Identify who is exposed, who owns each action, training, first aid, spill arrangements and the separate emergency response boundary.
Record, brief and review
Record significant findings, remaining actions and evidence needed before release. Check controls in use. Reassess for changed product, concentration, quantity, temperature, spraying, location, equipment, symptoms, incidents or new supplier information.
Worked decision: HOLD the proposed task until the matching product/use information, exposure and ignition assessment, control verification and emergency arrangements are resolved by the responsible competent people. This learning example does not issue an operational assessment or authorise work.
Reliable identity and relevant supplier information are inputs to a workplace assessment, not substitutes for it.
Supplier information must meet the real work
Check that the label and safety data sheet match the actual formulation and revision. A familiar brand may have several products with different hazards. Find the relevant information on exposure, incompatibilities, first aid, fire and storage, then connect it to the method used on site. The supplier sheet informs the assessment; it cannot observe the workface for you.
Ask what the task adds: heat, mixing, spraying, confined conditions, high quantities, awkward access or adjacent trades can change exposure. Information about a liquid in a closed container may not describe all contaminants produced during spraying or later sanding. Where information is missing or inconsistent, hold the affected use and obtain suitable clarification.
Pictograms help communicate hazards but do not select the full control system. An unlabelled decanted bottle is not cleared by guessing its contents. Keep identification, handling and emergency information available to those who need it, including cleaners and waste handlers who may never see the original packaging.
Visual practice · Use labels and safety data intelligently
Actual SHAREsimulate model capture · An isocyanate coating is applied beside other trades. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Investigate 1: Worker in the shared area
A worker is visible beside the columns. The case supplies the coating application and other trades entering. Ask how exposure and access will be controlled; do not infer exposure levels or protective equipment suitability from the figure.
Investigate 2: Column beside the shared work area
The column and open work area show the construction setting. No product identity is visible here: use the coating information and task-specific assessment supplied for the actual work, rather than guess a substance from the model.
Investigate 3: Open route between columns
The open structure shows how people can share the area. In the fictional coating case, investigate the separation and communication arrangements before allowing other trades into an exposure area.
Supplier information must meet the real work
Check that the label and safety data sheet match the actual formulation and revision. A familiar brand may have several products with different hazards. Find the relevant information on exposure, incompatibilities, first aid, fire and storage, then connect it to the method used on site. The supplier sheet informs the assessment; it cannot observe the workface for you.
What is a safety data sheet and what is it not?
An SDS is supplier hazard and handling information; it is not a COSHH assessment of a particular workplace task. Check the product identity and revision, hazard classification, exposure controls, first aid, fire response, stability/compatibility and disposal information. Then observe the task: concentration, temperature, quantity, transfer, nearby people and by-products can change risk.
How can the ISO 45001 hierarchy of controls turn chemical hazard information into effective exposure controls?
SDS, REACH and CLP information should be used to identify hazards, exposure routes, storage requirements, emergency arrangements and controls for the actual task. A strong COSHH assessment uses supplier information but does not stop there. It looks at the real work: how the chemical is handled, whether it is sprayed or heated, whether it is used in a confined space, whether it contacts skin, whether it is mixed, whether workers understand controls and whether nearby people can be exposed.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What is a safety data sheet and what is it not?
An SDS is supplier hazard and handling information; it is not a COSHH assessment of a particular workplace task.
Check the product identity and revision, hazard classification, exposure controls, first aid, fire response, stability/compatibility and disposal information. Then observe the task: concentration, temperature, quantity, transfer, nearby people and by-products can change risk. The SDS may not cover fume or dust generated by cutting, heating or mixing. If the sheet is missing, outdated or for another formulation, the buyer and supervisor should hold use until the information is corrected and the assessment reviewed.
How can the ISO 45001 hierarchy of controls turn chemical hazard information into effective exposure controls?
SDS, REACH and CLP information should be used to identify hazards, exposure routes, storage requirements, emergency arrangements and controls for the actual task.
A strong COSHH assessment uses supplier information but does not stop there. It looks at the real work: how the chemical is handled, whether it is sprayed or heated, whether it is used in a confined space, whether it contacts skin, whether it is mixed, whether workers understand controls and whether nearby people can be exposed.
The assessment should be reviewed when classification changes, a new SDS is received, the task changes, workers report symptoms, monitoring suggests exposure, a spill occurs or a safer alternative becomes available.
This is also where procurement, stores and operations need to communicate. A new chemical should not reach a work area before assessment, storage and training are ready.
Translating information into controls
Information found
Workplace question
Likely action
Corrosive classification
Could skin or eye contact occur?
Splash controls, gloves, goggles and eyewash.
Flammable classification
Could vapour ignite?
DSEAR review, storage and ignition control.
Respiratory sensitiser
Could workers inhale it?
Substitution, enclosure, LEV, RPE and health surveillance.
WEL in SDS section 8
Could airborne exposure approach the limit?
Exposure monitoring and control review.
Incompatibility in section 10
Could it be stored or mixed wrongly?
Segregation and decanting controls.
Restriction or authorisation note
Is use permitted and proportionate?
Procurement review and substitution.
Worked control choice: a corrosive cleaner at a workshop
Use HSE’s five-level hierarchy to choose stronger measures before PPE. ERICPD is a useful six-part teaching mnemonic; it is not a separate legal test. The example maps both approaches to the real task. Apply HSENI COSHH guidance for a Northern Ireland workplace. Emergency washing and evacuation limit consequences; they do not prevent the original contact or mixing.
How can the ERICPD hierarchy of controls turn chemical hazard information into effective exposure controls?
ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
Worked activity: Task application for What are chemical classification, REACH, CLP and safety data sheets?
Activity and release context
A strong COSHH assessment uses supplier information but does not stop there. It looks at the real work: how the chemical is handled, whether it is sprayed or heated, whether it is used in a confined space, whether it contacts skin, whether it is mixed, whether workers understand controls and whether nearby people can be exposed.
Avoid an unnecessary corrosive cleaner or open-decanting task at a workshop wash station.
Buyer and task owner record why cleaning is needed and inspect whether the old task/product has actually been removed. Reappearance of an unapproved container stops use.
Trial a less hazardous, ready-to-use formulation; compare the whole hazard profile and cleaning performance before approval.
COSHH assessor matches label and SDS to the actual formulation and observes the trial. A new sensitiser, flammability or ineffective cleaning requires reassessment; "dilute" is not proof of safety.
Use a chemically compatible closed dispensing connection and splash containment instead of pouring concentrate near the face.
Engineer commissions the connection, leak control and safe shutoff; operator checks before use and facilities maintain it. Leak, loose fitting or blocked containment stops dispensing until repaired.
Administrative / Control and Discipline HSE hierarchy
Keep product identity, approved use, SDS revision and task instruction together at the wash station; brief a replacement or contractor worker.
Supervisor observes one use and tests the missing-label response. Mismatched bottle or superseded instruction means quarantine, assessment review and a recorded restart decision.
Select chemical splash eye/face protection and compatible gloves for remaining contact risk; include fit, other PPE and cleaning/replacement limits.
Assessor records selection for the actual product; wearer and supervisor inspect condition. Damaged, unsuitable or unavailable PPE stops exposed work; PPE does not repair a failed dispensing system.
How can the ISO 45001 hierarchy of controls turn chemical hazard information into effective exposure controls?
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").
Worked activity: Task application for What are chemical classification, REACH, CLP and safety data sheets?
Activity and release context
A strong COSHH assessment uses supplier information but does not stop there. It looks at the real work: how the chemical is handled, whether it is sprayed or heated, whether it is used in a confined space, whether it contacts skin, whether it is mixed, whether workers understand controls and whether nearby people can be exposed.
Avoid an unnecessary corrosive cleaner or open-decanting task at a workshop wash station.
Buyer and task owner record why cleaning is needed and inspect whether the old task/product has actually been removed. Reappearance of an unapproved container stops use.
Trial a less hazardous, ready-to-use formulation; compare the whole hazard profile and cleaning performance before approval.
COSHH assessor matches label and SDS to the actual formulation and observes the trial. A new sensitiser, flammability or ineffective cleaning requires reassessment; "dilute" is not proof of safety.
Use a chemically compatible closed dispensing connection and splash containment instead of pouring concentrate near the face.
Engineer commissions the connection, leak control and safe shutoff; operator checks before use and facilities maintain it. Leak, loose fitting or blocked containment stops dispensing until repaired.
Administrative / Control and Discipline HSE hierarchy
Keep product identity, approved use, SDS revision and task instruction together at the wash station; brief a replacement or contractor worker.
Supervisor observes one use and tests the missing-label response. Mismatched bottle or superseded instruction means quarantine, assessment review and a recorded restart decision.
Select chemical splash eye/face protection and compatible gloves for remaining contact risk; include fit, other PPE and cleaning/replacement limits.
Assessor records selection for the actual product; wearer and supervisor inspect condition. Damaged, unsuitable or unavailable PPE stops exposed work; PPE does not repair a failed dispensing system.
Apply the learning
The crew has a safety data sheet for a different hardener and an unlabelled decanted bottle.
Decision and explanation
Hold use while product identity and correct information are established and the task assessment is checked.
Reliable identity and relevant supplier information are inputs to a workplace assessment, not substitutes for it.
Lesson 3
Choose controls in the right order
Prioritise elimination, substitution and source control, then coordinate remaining exposure controls for all affected people.
Reduce exposure before relying on personal equipment
Ask first whether the hazardous product or activity is necessary. A less hazardous product, ready-mixed material, off-site preparation or a different application method may remove or reduce exposure, provided the alternative is assessed for its own risks and performance. Substitution must be a considered change rather than an unverified purchase.
Where risk remains, prevent release or capture it at source. Plan suitable enclosure, local extraction, controlled mixing and application areas. Organise sequencing and separation to protect people who are not carrying out the task. Good housekeeping, hygiene, training and properly selected personal equipment support the engineered method.
Make the control observable. “Use ventilation” is too vague if nobody knows the required extraction, capture position or failure response. Establish who checks the equipment, what indicates a problem and when the task stops. A respirator worn by the operator does not protect an unbriefed electrician entering the shared area.
Locate the lungs, branching airways and diaphragm below them. The cutaway reveals structures normally hidden by the chest wall.
Trace the source-to-breathing-zone route in this lesson. Which change would prevent the contaminant reaching the person?
educational illustration · healthy anatomy; enlarged details and teaching colours.View full detail ↗Under the skin surface
Explore an enlarged section of hair-bearing skin, with a hand and forearm for context. Layers, glands, nerves and vessels are enlarged for clarity.
Use the task in this lesson to identify contact, repeated wet work or contamination. Which change reduces contact before relying on gloves?
educational illustration · healthy anatomy; enlarged details and teaching colours.
Visual practice · Choose controls in the right order
SHAREhub photographic illustration · Local extraction and chemical containers at a workplace assessment station. Use the written case for the exercise; this image does not prove a defect or safe system.Reduce exposure before relying on personal equipment
Ask first whether the hazardous product or activity is necessary. A less hazardous product, ready-mixed material, off-site preparation or a different application method may remove or reduce exposure, provided the alternative is assessed for its own risks and performance. Substitution must be a considered change rather than an unverified purchase.
How can the ISO 45001 hierarchy of controls guide controls after a hazardous-substance health-risk assessment?
ERICPD helps move the assessment from paperwork to stronger, practical control of exposure. For hazardous substances, the hierarchy is critical. Removing the substance or process is stronger than controlling dust after it is created.
How harm develops in the linked model
Some products contain isocyanates that can cause occupational asthma and skin effects. Risk depends on product, method, heating or spraying and actual exposure, not just the two-pack label.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How can the ISO 45001 hierarchy of controls guide controls after a hazardous-substance health-risk assessment?
ERICPD helps move the assessment from paperwork to stronger, practical control of exposure.
For hazardous substances, the hierarchy is critical. Removing the substance or process is stronger than controlling dust after it is created. Using pellets instead of powder, pre-mixed materials instead of dry mixing, water suppression, closed transfer and enclosure can all reduce exposure before people need RPE.
Administrative controls still matter, but they should support stronger controls. Written procedures, permits, restricted access and supervision are weak if the process still releases uncontrolled dust, vapour or fume. PPE and RPE can be essential, but they are vulnerable to poor fit, discomfort, wrong filter selection, poor maintenance and human behaviour.
Good control should be designed, used, maintained and checked. LEV requires correct design, hood positioning, statutory thorough examination and worker understanding. RPE needs selection, face fit, storage, cleaning and replacement. Gloves need compatibility checks because some chemicals pass through common glove materials.
For a solvent cleaning task, first ask whether the process can avoid the chemical or the cleaning step. A less hazardous product may substitute only after checking its actual formulation, use and waste route. Closed dispensing and local exhaust ventilation then provide engineering control for the residual airborne exposure; gloves and RPE are selected for remaining skin or inhalation routes, not as permission to leave a container open. ERICPD Eliminate/Reduce/Isolate/Control/PPE aligns with elimination, substitution, engineering, administrative control and PPE, while Discipline is the continuing check of whether each layer works.
The assessor records the product identity and safety data, task duration, quantity, bystanders, existing controls and any applicable workplace exposure limit. A competent person chooses a sampling strategy for the substance and exposure period; a compliant eight-hour average does not prove that a short peak, skin exposure or sensitisation risk is controlled. The supervisor checks container closure, extraction function, storage and spill response before release and repeats the check after a process change. If the material is unknown, extraction fails, symptoms arise or a spill escapes the controlled area, stop the task, protect others and reassess before restart. Health-surveillance decisions follow the actual legal trigger and exposure evidence.
How can the ERICPD hierarchy of controls guide controls after a hazardous-substance health-risk assessment?
ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
Worked activity: Cleaner changed from spray to controlled wipe
Activity and exposure
Crownway Fuels Ltd uses a water-based cleaner on control-room desks; the outcome is to avoid unnecessary mist and skin contact.
Before work
Check whether cleaning is needed, choose a lower-hazard product and pre-dosed wipe or controlled cloth, brief hygiene and spill steps, and keep food and drink away.
During the activity
Use the small quantity and method assessed; avoid spraying into the breathing zone and remove contaminated cloths to the agreed waste route.
Hold or stop
Wrong product, decanted unlabelled bottle, eye/skin symptoms or unexpected strong vapour: stop, isolate the item and obtain competent advice.
Hand-back and release
Clean the area, remove waste, wash hands, close any incident or product mismatch and restock only the approved product.
Evidence to retain
Product ID, SDS version, task assessment, briefing and closed defect.
ERICPD controls for hazardous substances - ERICPD controls for hazardous substances
ERICPD level
Practical application
Evidence to check
Eliminate
Remove the hazardous substance or process, such as buying pre-cut materials or avoiding solvent cleaning.
Design/procurement review and substitution decision record.
Reduce
Use smaller quantities, lower concentration, less dusty forms, lower temperature or shorter exposure time.
Inventory limits, purchasing standards and task design.
Isolate
Use closed systems, enclosure, segregation, restricted access and sealed transfer.
Equipment design, access control and inspection records.
Control
Use LEV, ventilation, wet methods, safe handling, hygiene, storage separation and spill procedures.
LEV test, maintenance, monitoring and inspection findings.
PPE
Use suitable gloves, eye protection, coveralls and RPE where exposure remains.
Compatibility checks, face-fit records, issue and maintenance records.
Discipline
Train, supervise, audit, investigate defects and review after change.
Training matrix, supervisor checks, worker feedback and action close-out.
How can the ISO 45001 hierarchy of controls guide controls after a hazardous-substance health-risk assessment?
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").
Worked activity: Cleaner changed from spray to controlled wipe
Activity and exposure
Crownway Fuels Ltd uses a water-based cleaner on control-room desks; the outcome is to avoid unnecessary mist and skin contact.
Before work
Check whether cleaning is needed, choose a lower-hazard product and pre-dosed wipe or controlled cloth, brief hygiene and spill steps, and keep food and drink away.
During the activity
Use the small quantity and method assessed; avoid spraying into the breathing zone and remove contaminated cloths to the agreed waste route.
Hold or stop
Wrong product, decanted unlabelled bottle, eye/skin symptoms or unexpected strong vapour: stop, isolate the item and obtain competent advice.
Hand-back and release
Clean the area, remove waste, wash hands, close any incident or product mismatch and restock only the approved product.
Evidence to retain
Product ID, SDS version, task assessment, briefing and closed defect.
A coating is proposed in an occupied work zone with only the applicator wearing a mask.
Decision and explanation
Review less hazardous methods and establish suitable source controls, separation and protection for everyone affected before application.
Prioritise elimination, substitution and source control, then coordinate remaining exposure controls for all affected people.
Lesson 4
Model practice: cement reaches the skin
Wet cement can cause serious injury; prevent prolonged contact and provide prompt suitable decontamination and response.
The familiar material can cause serious harm
The model places wet cement and chemicals in a working area. Look beyond the bag or mixer to the routes of contact: hands, knees, boots, clothing, eyes and dust from dry handling. A familiar material may be treated casually precisely because it appears every day. Familiarity does not limit the severity of burns or dermatitis.
Work through the five model decisions by establishing what the crew is doing and which controls are actually available. A product sheet does not demonstrate that workers can wash contamination off promptly, avoid kneeling in wet mix or remove contaminated clothing safely. The controls have to be usable at the place and time of exposure.
After the model, distinguish immediate response from prevention. Exposure needs the planned first-aid response and appropriate medical support where indicated. Before restarting, review the method, tools, personal protection and welfare that permitted contamination. Replacing a pair of gloves without changing the repeated contact may leave the main exposure route intact.
Visual practice · Model practice: cement reaches the skin
Actual SHAREsimulate model capture · Wet cement and unassessed chemicals reach the skin. The exercise description supplies the scenario; a still image cannot establish hidden conditions.The familiar material can cause serious harm
The model places wet cement and chemicals in a working area. Look beyond the bag or mixer to the routes of contact: hands, knees, boots, clothing, eyes and dust from dry handling. A familiar material may be treated casually precisely because it appears every day. Familiarity does not limit the severity of burns or dermatitis.
Choose dry powder, wet cement or hardened-material cutting
Compare three tasks. Emptying a cement bag calls for controlled handling of dry powder and its airborne and skin-contact routes. Screeding brings prolonged wet alkaline contact, contaminated clothing and welfare into the decision.
How harm develops in the linked model
Wet cement can cause serious alkali burns and dermatitis. Additives, solvents or other substances may introduce further routes of exposure and health effects.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Choose dry powder, wet cement or hardened-material cutting
Compare three tasks. Emptying a cement bag calls for controlled handling of dry powder and its airborne and skin-contact routes. Screeding brings prolonged wet alkaline contact, contaminated clothing and welfare into the decision. Cutting hardened concrete or mortar needs a separate assessment of dust, including silica-bearing material; it is not answered by the cement-bag assessment.
Best-practice guide · six simple steps
Best-practice guide: Cement Dust
Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.
Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.
Read all six steps as text
1. Choose dry powder, wet cement or hardened-material cutting
Compare three tasks.
Avoid / redesign: Avoid cutting or mixing on site by using pre-cut or pre-mixed products.
Control the task: Segregate dusty work, use exclusion zones and protect adjacent trades.
Verify before release: Design and procurement review.
Compare three tasks. Emptying a cement bag calls for controlled handling of dry powder and its airborne and skin-contact routes. Dry cement powder irritates airways and skin; wet cement can cause serious alkaline burns and dermatitis.
Apply it: Which part of this plan would you check at the workface before authorising the task?
Use the evidence to improve the actual work arrangement.
Change at source: Avoid cutting or mixing on site by using pre-cut or pre-mixed products.
Make it observable: Design and procurement review.
Keep useful evidence: COSHH and construction dust assessment.
Dry cement powder irritates airways and skin; wet cement can cause serious alkaline burns and dermatitis. Cutting hardened concrete or mortar can also release respirable crystalline silica, a separate long-term lung hazard. COSHH and construction dust assessment.
Apply it: What evidence would show that the change improves this task, rather than only completing a record?
Connect the task, the route to the person and the control that can fail.
Airway irritation: Dust irritates nose, throat and airways.
Silica-related lung disease: Fine RCS particles lodge deep in the lungs.
Respiratory symptoms needing assessment: Cement powder irritates airways; assess the actual dust and other agents before attributing a disease.
Airway irritation: Dust irritates nose, throat and airways. Silica-related lung disease: Fine RCS particles lodge deep in the lungs. Respiratory symptoms needing assessment: Cement powder irritates airways; assess the actual dust and other agents before attributing a disease.
Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?
Start with the stronger practicable options and verify their effect.
Eliminate: Avoid cutting or mixing on site by using pre-cut or pre-mixed products.
Reduce: Reduce bag handling, cutting time, powder quantities and wet contact.
Isolate: Segregate dusty work, use exclusion zones and protect adjacent trades.
Control: Use water suppression, on-tool extraction, LEV, vacuum cleaning and welfare.
PPE: Use suitable RPE, eye protection, gloves, clothing and footwear.
Eliminate: Avoid cutting or mixing on site by using pre-cut or pre-mixed products. Reduce: Reduce bag handling, cutting time, powder quantities and wet contact. Isolate: Segregate dusty work, use exclusion zones and protect adjacent trades. Control: Use water suppression, on-tool extraction, LEV, vacuum cleaning and welfare. PPE: Use suitable RPE, eye protection, gloves, clothing and footwear. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?
Follow the official sources below and retain the task-specific evidence.
Official guidance: HSE hierarchy of controls
Official guidance: HSE cement health risks
Task decision: COSHH and construction dust assessment.
Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status.
Apply it: Which official source and full-topic section will you use to resolve the next decision?
Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.
For each task identify the worker, nearby people, source-control method and a supervisor’s observable check. A missing water supply, ineffective extraction or unusable washing facility is a control failure to correct before work proceeds. Use the existing skin-and-eye route immediately after contact, then investigate the task and prevention arrangements separately; a normal air result does not establish safe skin contact.
BuildOut: a screed crew arrives before welfare is ready
Illustrative example. A fictional crew has gloves and boots, but the wash point is unavailable and wet material may become trapped inside footwear.
Decision. The supervisor holds wet work until suitable washing and emergency arrangements work, and briefs prompt contamination reporting.
Evidence to check. Task-specific assessment, accessible water, suitable contact protection and a practised route from the workface.
Hold or escalation point. Do not start because PPE is present when the required welfare or emergency control is missing.
Follow-up. Check facilities during the shift and carry the learning into the next site’s pre-start arrangements.
Wet mix is entering a worker’s boot and the nearest washing point has been disconnected during relocation.
Decision and explanation
Stop the exposure, use the planned decontamination and first-aid arrangements, and restore suitable controls and washing before restarting.
Wet cement can cause serious injury; prevent prolonged contact and provide prompt suitable decontamination and response.
Lesson 5
Prevent wet cement skin and eye contact
Prevent contact through method and suitable protection, and make prompt washing and response practical at the workface.
Plan the work position, equipment and washing
Wet cement can remain against the body inside a glove, boot or clothing. The exposure may continue while the person believes personal equipment is protecting them. Select suitable gloves, clothing and footwear for the task and wear them in the intended arrangement, while using tools and work methods that reduce direct contact.
Avoid kneeling in wet concrete or placing hands into the mix. Plan working positions and equipment before the delivery so the crew is not forced into contact to reach an awkward edge. Protect the eyes from splashes through suitable methods and equipment. Check compatibility with other required protection and the actual work movements.
Provide accessible washing and the prescribed response to contamination. Workers need to know how to remove contaminated items safely and how to obtain first aid without waiting for a break. Barrier creams do not replace protective methods or washing. Repeated redness, cracking or other symptoms need prompt reporting and appropriate assessment rather than being accepted as an unavoidable feature of the trade.
Explore an enlarged section of hair-bearing skin, with a hand and forearm for context. Layers, glands, nerves and vessels are enlarged for clarity.
Use the task in this lesson to identify contact, repeated wet work or contamination. Which change reduces contact before relying on gloves?
educational illustration · healthy anatomy; enlarged details and teaching colours.View full detail ↗The eye: surface and cutaway
Compare the visible eye with its enlarged side cutaway. Locate the clear front, lens and inner rear lining before following light and visual signals.
Distinguish the protective eye surface from the internal visual pathway. What task-specific protection or workstation change does this lesson require?
educational illustration · healthy anatomy; enlarged details and teaching colours.
Visual practice · Prevent wet cement skin and eye contact
SHAREhub photographic illustration · Worker inspecting dust extraction at an industrial materials handling point. Use the written case for the exercise; this image does not prove a defect or safe system.Plan the work position, equipment and washing
Wet cement can remain against the body inside a glove, boot or clothing. The exposure may continue while the person believes personal equipment is protecting them. Select suitable gloves, clothing and footwear for the task and wear them in the intended arrangement, while using tools and work methods that reduce direct contact.
How should skin and eye exposure to wet cement be controlled?
Prevent wet cement reaching skin or eyes; if contact occurs, remove it promptly and follow the chemical-burn emergency route. Wet cement is strongly alkaline. Contact trapped in boots, gloves or clothing can keep burning even if pain seems modest at first.
How can cement dust affect health?
Cement can affect health through airway irritation, silica-related lung disease, skin burns, dermatitis, eye injury and sensitisation. Short-term inhalation can irritate the nose, throat and airways, causing coughing, sneezing, throat irritation or chest discomfort. Repeated high exposure may contribute to longer-term respiratory problems, particularly where silica-containing dust is involved.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should skin and eye exposure to wet cement be controlled?
Prevent wet cement reaching skin or eyes; if contact occurs, remove it promptly and follow the chemical-burn emergency route.
Wet cement is strongly alkaline. Contact trapped in boots, gloves or clothing can keep burning even if pain seems modest at first. Keep knees and feet out of wet concrete, use long-handled tools and barriers, and choose gloves suitable for high-pH alkalis with task-matched breakthrough time. Prevent cement entering the glove cuff; use suitable eye or face protection where splashes can occur. Provide nearby clean water, washing facilities and a plan to remove contaminated clothing safely.
For a suspected chemical burn or cement splash to skin or eyes, stop the task, protect helpers, call 999 and begin immediate flushing with plentiful cool or lukewarm water while help is arranged. Carefully remove contaminated clothing if safe; do not pull off material stuck to injured tissue or apply creams or neutralising chemicals. Follow the product safety data sheet and trained first-aid plan, and pass the product identity to clinicians. Do not send an affected worker back to wet work until medically assessed and the failed control is corrected.
On a small screen, scroll this table sideways to read all columns.
Wet cement contact controls
Decision
Control and check
Stop or escalation point
Task design
Pre-mixed delivery, long handles, dry standing areas, splash guards and suitable water access.
Hold work if safe access or washing is unavailable.
Skin and eye protection
High-pH compatible gloves, boots and splash protection; check fit, condition and glove cuffs.
Replace damaged PPE or a method that traps slurry.
First response
Stop exposure, summon trained help, call 999 for suspected chemical burn and flush promptly.
Any eye splash, burn or continuing pain needs urgent medical assessment.
Surveillance
Early skin checks, private symptom reporting and control feedback.
Repeated dermatitis or wet-contact near miss triggers task reassessment.
How can cement dust affect health?
Cement can affect health through airway irritation, silica-related lung disease, skin burns, dermatitis, eye injury and sensitisation.
Short-term inhalation can irritate the nose, throat and airways, causing coughing, sneezing, throat irritation or chest discomfort. Repeated high exposure may contribute to longer-term respiratory problems, particularly where silica-containing dust is involved.
Respirable crystalline silica is the serious long-term concern when cutting, drilling or breaking dried concrete, mortar, stone or masonry. Fine respirable particles can reach deep into the lungs and cause diseases such as silicosis and contribute to chronic obstructive pulmonary disease and lung cancer risk.
Skin and eye harm can be immediate. Wet cement is alkaline and may burn while trapped against skin, sometimes before the worker realises how serious it is. Cement can also abrade and irritate skin, while hexavalent chromium can cause allergic contact dermatitis in sensitised workers.
Health effects and warning signs
Health effect
How it develops
Warning signs
Airway irritation
Dust irritates nose, throat and airways.
Coughing, sneezing, sore throat or chest tightness.
Silica-related lung disease
Fine RCS particles lodge deep in the lungs.
Persistent cough, breathlessness or reduced tolerance.
Respiratory symptoms needing assessment
Cement powder irritates airways; assess the actual dust and other agents before attributing a disease.
Wheeze, chest tightness or work-related breathing symptoms.
Alkaline burns
Wet cement trapped against skin causes chemical burns.
Redness, pain, blistering, ulceration or delayed pain.
Irritant dermatitis
Abrasive and alkaline contact damages skin barrier.
Dry, cracked, red or sore skin.
Allergic dermatitis
Chromate sensitisation triggers future reactions.
Recurring rash after small exposures.
Eye injury
Dust or splash irritates or burns the eye.
Pain, watering, redness or vision concern.
Apply the learning
A worker repeatedly kneels in wet concrete and treats damp clothing as normal until the break.
Decision and explanation
Change the method and work position to prevent contact and ensure suitable protection, washing and prompt reporting.
Prevent contact through method and suitable protection, and make prompt washing and response practical at the workface.
Lesson 6
Control dry handling, mixing and cleanup
Control exposure through handling, mixing and cleanup; a later dusty method can defeat the earlier source controls.
A clean-looking task can still create airborne exposure
Dry cement and other powdered products can release dust when bags are opened, poured, mixed or discarded. Design the process to minimise handling and release, using suitable pre-mixed or controlled-delivery options where practicable. The assessment must consider the mixture and task; cement, sand and other constituents are not one interchangeable dust hazard.
Keep effective controls close to the release. Position equipment and materials so the worker does not pour through their breathing zone or stand in a visible plume. Suitable extraction or other source controls need to match the process. Any personal respiratory protection is selected through the assessment and used alongside the remaining controls.
Cleanup belongs in the original plan. Dry sweeping, compressed air or shaking dusty bags can expose people after mixing has ended. Select a suitable controlled cleaning method and handle residues and packaging without redistributing contamination. Explain that absence of a visible cloud does not prove the air is suitable, and a thin deposit on a surface can become a later source.
Visual practice · Control dry handling, mixing and cleanup
Actual SHAREsimulate model capture · Wet cement and unassessed chemicals reach the skin. The exercise description supplies the scenario; a still image cannot establish hidden conditions.A clean-looking task can still create airborne exposure
Dry cement and other powdered products can release dust when bags are opened, poured, mixed or discarded. Design the process to minimise handling and release, using suitable pre-mixed or controlled-delivery options where practicable. The assessment must consider the mixture and task; cement, sand and other constituents are not one interchangeable dust hazard.
Which cement tasks create the highest risk?
Higher-risk tasks are those that create airborne dust, involve wet cement contact, trap contamination against skin or disturb hardened silica-containing materials. The highest dust tasks usually involve energy applied to dry or hardened materials: cutting, grinding, drilling, chasing, scabbling, breaking, sanding and dry sweeping. Mixing can also be high exposure if bags are tipped quickly or powders are poured from height.
How can the ISO 45001 hierarchy of controls reduce cement-dust exposure and skin contact?
Cement exposure should be controlled by eliminating dusty work where possible, reducing dust generation, isolating people, controlling at source and using PPE/RPE correctly. Control should start before work begins. Designers and planners should ask whether dusty work can be avoided through prefabrication, pre-cut materials, pre-mixed mortar, different fixings, safer sequencing or off-site cutting with better controls.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Which cement tasks create the highest risk?
Higher-risk tasks are those that create airborne dust, involve wet cement contact, trap contamination against skin or disturb hardened silica-containing materials.
The highest dust tasks usually involve energy applied to dry or hardened materials: cutting, grinding, drilling, chasing, scabbling, breaking, sanding and dry sweeping. Mixing can also be high exposure if bags are tipped quickly or powders are poured from height.
The highest skin tasks involve prolonged wet contact: laying blocks, screeding, kneeling in wet concrete, cleaning tools, handling wet mortar, carrying contaminated boards or allowing cement into boots and gloves.
Risk rises when tasks are indoors, poorly ventilated, close to other trades, rushed, carried out without water suppression or extraction, or cleaned using dry brooms.
High-risk cement tasks
Task
Main hazard
Control priority
Dry cutting concrete
RCS and nuisance dust.
Wet cutting or on-tool extraction.
Mixing cement powder
Airborne powder and skin/eye contact.
Low-dust method and eye/skin protection.
Breaking or chasing mortar
Dust and silica exposure.
Extraction, water suppression and segregation.
Screeding or concreting
Wet cement burns and dermatitis.
Skin protection, kneepads, washing and clothing control.
Cleaning tools
Wet cement contact and splashes.
Gloves, eyewash and wash facilities.
Dry sweeping
Re-suspends settled dust.
Vacuum or wet cleaning.
How can the ISO 45001 hierarchy of controls reduce cement-dust exposure and skin contact?
Cement exposure should be controlled by eliminating dusty work where possible, reducing dust generation, isolating people, controlling at source and using PPE/RPE correctly.
Control should start before work begins. Designers and planners should ask whether dusty work can be avoided through prefabrication, pre-cut materials, pre-mixed mortar, different fixings, safer sequencing or off-site cutting with better controls.
Where the task remains, control at source. Wet cutting, water suppression, on-tool extraction, enclosed mixing, low-drop transfer, vacuum cleaning and segregation are stronger controls than relying only on disposable masks.
PPE and RPE are still important where residual risk remains, but they need fit, compatibility, training, storage, maintenance and supervision. A worker wearing a mask incorrectly while dry cutting is not protected.
Check the shelf date when receiving and issuing cement, and rotate stock. HSE explains that the ingredient used to reduce hexavalent chromium is effective for a limited time; using stored bags after that date can increase allergic-dermatitis risk. A stores check should therefore cover the marked date as well as bag condition and dust control.
How can the ERICPD hierarchy of controls reduce cement-dust exposure and skin contact?
ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
Worked activity: Task application for What is cement dust and why is it hazardous at work?
Activity and release context
Where the task remains, control at source. Wet cutting, water suppression, on-tool extraction, enclosed mixing, low-drop transfer, vacuum cleaning and segregation are stronger controls than relying only on disposable masks.
Avoid cutting or mixing on site by using pre-cut or pre-mixed products.
Design and procurement review.
Reduce
Reduce bag handling, cutting time, powder quantities and wet contact.
Method statement and task observation.
Isolate
Segregate dusty work, use exclusion zones and protect adjacent trades.
Site logistics and barriers.
Control
Use water suppression, on-tool extraction, LEV, vacuum cleaning and welfare.
Inspection and test records.
PPE
Use suitable RPE, eye protection, gloves, clothing and footwear.
Fit testing and PPE checks.
Discipline
Train, supervise, monitor, maintain and act on symptoms.
Briefings, audits and health surveillance.
How can the ISO 45001 hierarchy of controls reduce cement-dust exposure and skin contact?
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").
Worked activity: Task application for What is cement dust and why is it hazardous at work?
Activity and release context
Where the task remains, control at source. Wet cutting, water suppression, on-tool extraction, enclosed mixing, low-drop transfer, vacuum cleaning and segregation are stronger controls than relying only on disposable masks.
Avoid cutting or mixing on site by using pre-cut or pre-mixed products.
Design and procurement review.
Reduce
Reduce bag handling, cutting time, powder quantities and wet contact.
Method statement and task observation.
Isolate
Segregate dusty work, use exclusion zones and protect adjacent trades.
Site logistics and barriers.
Control
Use water suppression, on-tool extraction, LEV, vacuum cleaning and welfare.
Inspection and test records.
PPE
Use suitable RPE, eye protection, gloves, clothing and footwear.
Fit testing and PPE checks.
Discipline
Train, supervise, monitor, maintain and act on symptoms.
Briefings, audits and health surveillance.
Apply the learning
The mixing task is controlled, but the crew plans to dry sweep residues through the shared corridor.
Decision and explanation
Use the assessed controlled cleaning and waste method while protecting adjacent people.
Control exposure through handling, mixing and cleanup; a later dusty method can defeat the earlier source controls.
Lesson 7
Recognise isocyanate exposure and sensitisation
Product and application method together determine exposure; spraying needs a suitable assessed control system and protection of others.
Application method changes who is exposed
Some coatings, foams, adhesives and related products contain isocyanates. Use the actual product information and task assessment rather than relying on a trade name or the fact that a product is described as two-part. Mixing, application, curing, cleaning and heating can create different conditions requiring consideration.
Spraying can produce fine droplets that travel beyond the applicator. A nearby worker may be exposed while believing they are outside the task. Sensitisation and occupational asthma are serious concerns; a person who becomes sensitised may react to subsequent exposure at low levels. The correct response is effective prevention and health arrangements, not waiting for a distinctive smell or immediate discomfort.
Compare suitable lower-exposure alternatives and application methods through competent assessment. Where use remains, define the controlled area, source controls, appropriate respiratory and skin protection, cleaning and re-entry conditions. Do not extend a control specified for one spray system to every product or outdoor application without checking the actual requirements.
Visual practice · Recognise isocyanate exposure and sensitisation
SHAREhub photographic illustration · Male spray painter wearing a full air-fed visor and protective coveralls while painting a car door in a UK spray booth. Use the written case for the exercise; this image does not prove a defect or safe system.Application method changes who is exposed
Some coatings, foams, adhesives and related products contain isocyanates. Use the actual product information and task assessment rather than relying on a trade name or the fact that a product is described as two-part. Mixing, application, curing, cleaning and heating can create different conditions requiring consideration.
What is isocyanate asthma in plain English?
It is asthma caused by the immune system becoming sensitised to isocyanates at work. Isocyanates are chemicals used in many polyurethane-based products. They are found in 2-pack paints, vehicle refinishing, spray coatings, foams, adhesives, resins and some construction products.
Where are isocyanate exposures found?
Isocyanates are not limited to vehicle paint shops; they appear across industries and products. The classic high-risk example is motor vehicle repair using 2K spray paints, but other exposures include construction spraying, floor screeds, adhesives, insulation foam, polyurethane manufacture, coatings, lacquers, resins and maintenance work on cured or uncured products. The risk is greatest where products are sprayed or heated, where ventilation is poor, where workers work close to the source, where bystanders are nearby, or where people clean spray guns and equipment without proper controls.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What is isocyanate asthma in plain English?
It is asthma caused by the immune system becoming sensitised to isocyanates at work.
Isocyanates are chemicals used in many polyurethane-based products. They are found in 2-pack paints, vehicle refinishing, spray coatings, foams, adhesives, resins and some construction products. Exposure can occur through inhaling aerosol, vapour or mist, and through skin contact with some products. See HSE - Isocyanates in construction.
Once a worker becomes sensitised, very small exposures may trigger asthma symptoms. This is why control cannot depend on whether the worker feels fine today. It must depend on preventing exposure, monitoring whether controls work and acting early on symptoms.
Respiratory sensitiser — A substance that can cause allergic-type asthma after exposure. Exposure must be kept as low as reasonably practicable.
2K paint — Two-pack paint often containing isocyanate hardener. Common bodyshop and spray risk.
Aerosol mist — Fine droplets generated by spraying. Can be invisible and inhaled deeply.
Clearance time — Time needed for spray booth/room air to clear after spraying. Workers must keep BA on until safe to remove.
Biological monitoring — Urine test indicating whether exposure occurred. Checks real-world control effectiveness.
Where are isocyanate exposures found?
Isocyanates are not limited to vehicle paint shops; they appear across industries and products.
The classic high-risk example is motor vehicle repair using 2K spray paints, but other exposures include construction spraying, floor screeds, adhesives, insulation foam, polyurethane manufacture, coatings, lacquers, resins and maintenance work on cured or uncured products.
The risk is greatest where products are sprayed or heated, where ventilation is poor, where workers work close to the source, where bystanders are nearby, or where people clean spray guns and equipment without proper controls.
2K vehicle paint spraying — High aerosol mist exposure. Spray booth, air-fed BA, clearance time and monitoring.
Construction spray coatings — Mist may drift and expose others. Enclosure, exclusion and wind/ventilation planning.
Foam and polyurethane work — MDI/TDI exposure possible depending on product. COSHH assessment and skin/respiratory controls.
Adhesives/resins/floor screeds — Exposure may be less obvious than spraying. Product identification, ventilation and gloves/RPE.
Spray gun cleaning — Can create significant exposure after main spray task. Controlled cleaning method and RPE.
Bystander work — Others may enter before area is clear. Access control and clearance-time signage.
How does sensitisation happen?
Sensitisation means the body becomes unusually reactive after exposure.
The mechanism matters because the first serious warning may not occur during the first exposure. A worker can become sensitised over time, then later react to very small amounts. Symptoms may appear after work or during the night, so workplaces must ask about timing and patterns, not only what happens during the shift. See HSE - Isocyanates in construction.
Skin exposure may also matter. Poor glove selection, contaminated coveralls, poor cleaning and touching contaminated surfaces can contribute to overall risk and dermatitis.
Latency — Symptoms may develop after a period of exposure. Do not assume early symptom-free work is safe.
Delayed symptoms — Symptoms can appear hours after work. Health surveillance should ask about evening/early-morning symptoms.
Tiny triggers — After sensitisation, low exposure may trigger asthma. Prevent further exposure pending competent advice.
Skin and respiratory risk — Isocyanates can affect breathing and skin. Use respiratory and skin health surveillance where relevant.
Control reliance — RPE behaviour and booth clearance can make or break control. Supervise and biologically monitor.
Apply the learning
The task changes from a controlled brush application to spraying beside other contractors.
Decision and explanation
Hold the changed application and reassess the product, aerosol exposure, controlled area and suitable controls for all affected people.
Product and application method together determine exposure; spraying needs a suitable assessed control system and protection of others.
Lesson 8
Model practice: the coating beside other trades
The coating controls must protect all affected people throughout application, clearing, cleaning and re-entry.
Protect the area, not only the applicator
The construction model places an isocyanate-coating proposal beside other work. Trace where the material is mixed, applied and cleaned, how air moves and where people may approach. The scene does not establish a safe atmosphere or re-entry time. Those decisions depend on the product, application, control system and competent assessment.
Work through the five stages by asking who can be harmed and which evidence verifies the controls. A casual mask choice, a strong smell or a temporary warning does not demonstrate suitable respiratory protection or effective separation. The applicator's protection is only one part of a system that also protects nearby trades, visitors and cleaners.
Return with a clear hold or restart recommendation. Identify the missing task assessment, the owner of the work zone, the source-control checks and the briefing required before anyone enters. If the coating method, ventilation or area changes, stop and review the affected assumptions rather than leaving other workers to discover the change through symptoms.
Visual practice · Model practice: the coating beside other trades
Actual SHAREsimulate model capture · An isocyanate coating is applied beside other trades. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Protect the area, not only the applicator
The construction model places an isocyanate-coating proposal beside other work. Trace where the material is mixed, applied and cleaned, how air moves and where people may approach. The scene does not establish a safe atmosphere or re-entry time. Those decisions depend on the product, application, control system and competent assessment.
How should COSHH assessment be carried out?
A suitable COSHH assessment must identify the product, task, route, exposure group and control reliability. A weak assessment says 'wear mask'. A strong assessment identifies the isocyanate type, product use, spray method, booth or room condition, clearance time, RPE specification, breathing-air quality, bystander exposure, skin contact, cleaning work, maintenance and biological monitoring plan.
Why is spraying especially high risk?
Spraying breaks liquid product into fine droplets that can travel, remain airborne and be inhaled. HSE guidance highlights that spraying can produce very high exposure because mist droplets are easily breathed in and because more product is used in a short time. Conventional spraying, HVLP and airless systems all have different overspray and injection hazards, so the equipment choice matters.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should COSHH assessment be carried out?
A suitable COSHH assessment must identify the product, task, route, exposure group and control reliability.
A weak assessment says 'wear mask'. A strong assessment identifies the isocyanate type, product use, spray method, booth or room condition, clearance time, RPE specification, breathing-air quality, bystander exposure, skin contact, cleaning work, maintenance and biological monitoring plan. See COSHH Regulations 2002; COSHH Regulations (Northern Ireland) 2003.
Assessment must include foreseeable poor practice: rushing, lifting visors, cleaning guns, spraying small jobs outside a booth, allowing others into the area too early and failing to maintain air supply.
Which isocyanate product is used? — MDI, TDI, HDI/IPDI risks and monitoring differ. SDS and product register.
Is it sprayed, brushed, mixed or heated? — Aerosol generation changes exposure. Task observation.
Where does mist go? — Bystanders and leakage may be exposed. Booth smoke test and clearance measurement.
What RPE is specified? — For isocyanate paint spraying, filtering respirators are unsuitable; suitable air-fed breathing apparatus is required. Assess other isocyanate processes for their actual task. RPE assessment and maintenance record.
How is control verified? — Controls can fail silently. Biological monitoring and surveillance.
What symptoms have been reported? — Health reports may show failure. Confidential reporting and OH referral.
Why is spraying especially high risk?
Spraying breaks liquid product into fine droplets that can travel, remain airborne and be inhaled.
HSE guidance highlights that spraying can produce very high exposure because mist droplets are easily breathed in and because more product is used in a short time. Conventional spraying, HVLP and airless systems all have different overspray and injection hazards, so the equipment choice matters. See HSG276 - Isocyanate paint spraying; INDG388 - Safety in isocyanate paint spraying.
The spray area must be managed as a contaminated atmosphere until it is clear. A worker who lifts an air-fed visor to inspect finish immediately after spraying can inhale mist despite having worn BA during the spraying pass.
Mist leakage — Can expose bystanders outside booth/room. Maintain enclosure and extraction.
Clearance time unknown — Workers may remove BA too soon. Measure and display clearance time.
Visor lifted — High exposure can occur after spraying. Keep BA on until outside clear area.
Spray gun cleaning — Exposure can occur during wash-out. Use controlled cleaning and RPE.
Outdoor spraying — Wind can carry mist. Plan exclusion, wind direction and controls.
Airless injection hazard — High pressure can inject paint into skin. Guard tips, pressure control and training.
Apply the learning
A spray application is proposed beside electricians, with no verified exclusion or re-entry arrangement.
Decision and explanation
Keep application held until the competent task assessment, suitable control system and protection of other people are established.
The coating controls must protect all affected people throughout application, clearing, cleaning and re-entry.
Lesson 9
Verify extraction and respiratory protection
Respiratory protection is hazard, task and wearer specific; it supports verified source controls and cannot be selected by appearance.
The right equipment must be effective in use
Extraction must suit the contaminant and source, capture where release occurs and discharge safely. A fan moving room air is not automatically local exhaust ventilation. Check the arrangement, condition and operating indicators through the competent method, and stop when a failure makes the assessed control ineffective.
Respiratory protective equipment must suit the hazard, required protection, wearer and task. Tight-fitting equipment needs the relevant face-fit arrangements and a face seal in use. A disposable particulate mask does not protect against every vapour, and air-purifying equipment does not supply oxygen. Some tasks require more specialised systems selected by competent people.
Plan compatible personal protection, cleaning, maintenance, storage and replacement. A test or certificate does not prove that the worker has fitted and used the equipment correctly today. Ask the wearer to explain checks and failure responses, while ensuring the overall method continues to reduce exposure at source. Personal equipment cannot repair an unassessed product or an uncontrolled shared area.
Visual practice · Verify extraction and respiratory protection
SHAREhub photographic illustration · Local extraction and chemical containers at a workplace assessment station. Use the written case for the exercise; this image does not prove a defect or safe system.The right equipment must be effective in use
Extraction must suit the contaminant and source, capture where release occurs and discharge safely. A fan moving room air is not automatically local exhaust ventilation. Check the arrangement, condition and operating indicators through the competent method, and stop when a failure makes the assessed control ineffective.
How should local exhaust ventilation, RPE and PPE be managed?
Local exhaust ventilation (LEV), respiratory protective equipment (RPE) and personal protective equipment (PPE) only protect people when they are correctly selected, fitted, used, maintained, examined and supervised. MR3 (January2025) specifies enclosed extracted gun washing; if washings must be sprayed, use the booth/room and airline breathing apparatus. Keep airline protection during spraying and the measured clearance period; do not lift the facepiece to inspect the finish.
What should be controlled around RPE, air-fed BA and spray booths?
RPE is a life-critical control in isocyanate spraying and must be treated as a programme, not a mask purchase. For isocyanate paint spraying, ordinary filtering respirators are unsuitable. Select suitable air-fed breathing apparatus to the HSE task guidance, with assigned protection factor at least 20 and a low-flow indicator.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should local exhaust ventilation, RPE and PPE be managed?
Local exhaust ventilation (LEV), respiratory protective equipment (RPE) and personal protective equipment (PPE) only protect people when they are correctly selected, fitted, used, maintained, examined and supervised.
Local exhaust ventilation
Local exhaust ventilation (LEV) should capture the contaminant close to where it is generated and move it away from the breathing zone. The hood design, capture velocity, ducting, filter, discharge point and user position all matter. A system can be installed and still fail if the hood is too far from the source, airflow is blocked, filters are overloaded, dampers are altered or operators work outside the capture zone. LEV requires routine checks and a thorough examination and test by a competent person at least every 14 months unless a more frequent interval applies.
Respiratory protective equipment
Respiratory protective equipment (RPE) must match the substance, airborne concentration, oxygen level, task duration and wearer. Tight-fitting masks need face-fit testing and users need to be clean-shaven where the seal depends on the face. Filters must be correct for the contaminant and changed before breakthrough or clogging. RPE should be stored clean, inspected before use and supported by training so workers can carry out seal checks and recognise failure.
Gloves, coveralls and eye protection
Gloves should be selected using chemical compatibility and breakthrough information, not simply by colour or habit. Nitrile, latex, neoprene, PVC and other materials behave differently against different chemicals. Coveralls and aprons should prevent contamination of skin and clothing, while eye and face protection should match splash, mist, dust or corrosive risk. Personal protective equipment (PPE) needs cleaning, disposal or replacement rules so contamination is not carried into welfare areas, vehicles or homes.
Hygiene and welfare
Good COSHH control often depends on basic hygiene done consistently: clean handwashing facilities, no eating or drinking in contaminated areas, suitable changing arrangements, safe waste disposal, dust-free cleaning methods and contaminated clothing controls. Dry sweeping dusty material, using compressed air on clothing or sharing dirty gloves can defeat otherwise sensible controls.
MR3 (January2025) specifies enclosed extracted gun washing; if washings must be sprayed, use the booth/room and airline breathing apparatus. Keep airline protection during spraying and the measured clearance period; do not lift the facepiece to inspect the finish. The HSE LEV examination FAQ supports the GB 14-month thorough-examination/test expectation and retained records; routine checks and maintenance continue between examinations. Confirm applicable shorter intervals and the separate NI requirement rather than treating an examination label as proof of daily control.
What should be controlled around RPE, air-fed BA and spray booths?
RPE is a life-critical control in isocyanate spraying and must be treated as a programme, not a mask purchase.
For isocyanate paint spraying, ordinary filtering respirators are unsuitable. Select suitable air-fed breathing apparatus to the HSE task guidance, with assigned protection factor at least 20 and a low-flow indicator. A half-mask air-fed device in a spray room needs clear, continuing biological-monitoring evidence that exposure is adequately controlled; it is not the default choice. Verify manufacturer minimum flow, clean breathing-air quality, supply integrity and booth clearance before spraying and at use. HSG276 - Isocyanate paint spraying; HSG53 - Respiratory protective equipment at work. HSE paint-spraying RPE guidance
Tear-off visor covers, lighting, low-flow indicators, air-line checks and supervisor observation all matter because poor visibility or low air flow can tempt workers into unsafe behaviour.
Control
Good practice
Evidence
Air-fed BA
Suitable air-fed BA, APF at least 20, low-flow indicator; half-mask only with continuing biological-monitoring evidence.
Selection record, manufacturer minimum-flow and air-supply checks, low-flow test and monitoring review.
Breathing air quality
Clean air at required pressure/flow.
Air quality test and compressor maintenance.
Booth clearance time
Measured and communicated.
Clearance test and sign.
Extraction
Maintained and not leaking mist.
LEV/booth maintenance record.
Visor discipline
BA kept on until outside/clear.
Observation and training.
Fit testing
For tight-fitting RPE where used.
Fit-test record.
Apply the learning
A worker selects a disposable dust mask for an unassessed coating vapour because it was used on yesterday’s mixing job.
Decision and explanation
Hold the task and obtain competent selection of the complete control and respiratory-protection system for the actual hazard and wearer.
Respiratory protection is hazard, task and wearer specific; it supports verified source controls and cannot be selected by appearance.
Lesson 10
Identify lead before disturbing old finishes
Establish the material and control method before disturbance; old coatings can expose the operator and others through dust and contamination.
A modern tool does not make an old coating harmless
Lead may be present in older paint, pipework, flashings or other materials. The proposed disturbance method controls how it may be released. Sanding, abrasive work and heating can create significant exposure; intact appearance or a recent colour coat does not establish what lies beneath.
Establish suitable information before disturbance. Where lead may be present, the competent assessment determines investigation and the safer method. Avoid speculative scraping or heating to find out. Keep the affected area controlled while uncertainty is resolved and coordinate the findings with other trades who may cut, drill or clean the same surface.
Lead exposure is not confined to the person holding the tool. Dust can settle on clothing, hands, surfaces and welfare areas and be swallowed later. The assessment should include containment, source control, hygiene, cleaning and waste, as well as any monitoring or statutory medical arrangements. Do not copy numerical medical decisions into a supervisor's checklist; those belong to the relevant competent and medical process.
Visual practice · Identify lead before disturbing old finishes
Actual SHAREsimulate model capture · Old lead-containing paint is dry stripped. The exercise description supplies the scenario; a still image cannot establish hidden conditions.A modern tool does not make an old coating harmless
Lead may be present in older paint, pipework, flashings or other materials. The proposed disturbance method controls how it may be released. Sanding, abrasive work and heating can create significant exposure; intact appearance or a recent colour coat does not establish what lies beneath.
Where is lead dust found in real workplaces?
Lead dust risk is common where old materials, specialist materials or contaminated residues are disturbed. Construction and refurbishment are major risk settings because older buildings can contain lead-based paints, lead pipes, lead roofwork and contaminated dust in voids. The risk rises sharply when work changes from normal handling to high-energy disturbance such as abrasive sanding, needle-gunning, grinding, burning or blasting.
How should old lead paint be approached?
Old lead paint should be assumed possible until survey information or testing shows otherwise. Lead pigments were widely used historically, so refurbishment work needs a deliberate check before disturbing coatings. The safest plan is to avoid unnecessary disturbance.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Where is lead dust found in real workplaces?
Lead dust risk is common where old materials, specialist materials or contaminated residues are disturbed.
Construction and refurbishment are major risk settings because older buildings can contain lead-based paints, lead pipes, lead roofwork and contaminated dust in voids. The risk rises sharply when work changes from normal handling to high-energy disturbance such as abrasive sanding, needle-gunning, grinding, burning or blasting.
Industrial settings can also create lead dust or fume during battery work, foundry work, radiator repair, soldering, scrap processing, firing-range maintenance, stained glass work, ceramics, coatings removal and contaminated plant maintenance. The task can look small, but repeated exposure and poor hygiene can build a significant body burden.
HSE construction guidance identifies older coatings, pipework and roof materials; HSE lead-risk guidance also covers battery recovery, smelting, foundry, pigment and ceramic tasks. The transfer question is always what form of lead the process releases and who may breathe, swallow or carry it away.
Source
Example task
Main control focus
Lead-based paint
Sanding, scraping, heat stripping, burning or abrasive removal.
Identify coating, avoid high-dust methods, contain and clean.
Lead-coated steel
Cutting, grinding, welding or burning.
Avoid hot work where possible, use LEV and respiratory protection.
Lead pipework
Removal, cutting or replacement in older properties.
Prevent dust, manage waste and maintain hygiene.
Lead sheet and flashing
Roof work, cutting, shaping and removal.
Control handling contamination, cutting dust and welfare.
Battery and recycling work
Breaking, sorting, charging, smelting or residue cleaning.
Segregation, enclosure, hygiene and medical surveillance.
Firing ranges
Bullet trap cleaning and contaminated dust removal.
Specialist cleaning methods and strict contamination control.
Workshops and hobby-type tasks
Stained glass, solder, pigments and ceramics.
Substitution, ventilation, housekeeping and training.
How should old lead paint be approached?
Old lead paint should be assumed possible until survey information or testing shows otherwise.
Lead pigments were widely used historically, so refurbishment work needs a deliberate check before disturbing coatings. The safest plan is to avoid unnecessary disturbance. If removal is needed, choose methods that minimise dust and fume, protect other people, contain debris and make cleaning verifiable.
A common failure is to authorise sanding or burning because the job appears minor. A small job can contaminate a room, a van, a worker's clothing and nearby trades. The work pack should state what is being disturbed, how lead has been checked, what method is allowed, where the exclusion zone is, how waste is collected and what welfare is available before the first tool is used.
Decision
Good practice
Failure to avoid
Is lead present?
Use survey information, history and testing where needed.
Assuming paint is modern because it looks clean.
Can removal be avoided?
Over-board, encapsulate or leave undisturbed if safe and suitable.
Removing paint for convenience.
Which method?
Use low-dust, controlled methods and do not use blow lamps or gas torches on leaded paint, and keep hot-air or infrared equipment below 500°C.
Dry sanding, uncontrolled grinding or hot work.
Who is nearby?
Exclude other trades and protect occupants.
Letting dust spread through shared areas.
How will it be cleaned?
Use suitable vacuuming, damp cleaning and waste control.
Dry sweeping or compressed air.
What is the handback?
Inspect cleanliness, remove waste and confirm welfare/contamination controls.
Leaving residues for cleaners or occupants.
For the occupied-school hand-back, agree the acceptance method before starting: which areas are inspected, whether the competent assessment calls for sampling, who interprets any results, the decision criterion and who releases occupancy. Record failed areas and re-clean/recheck them. Do not invent a universal UK clearance number or require wipes for every small job. Off-site treatment avoids exposure at this workface but transfers a hazardous task to a competent facility; removal and packaging can still disturb lead.
Apply the learning
An old painted beam is about to be dry sanded, but its coating has not been assessed for lead.
Decision and explanation
Hold disturbance while suitable information and a competent task-specific lead-control method are established.
Establish the material and control method before disturbance; old coatings can expose the operator and others through dust and contamination.
Lesson 11
Model practice: dry stripping the old paint
Lead control starts before disturbance and continues through cleanup, hygiene and waste; symptoms and later tests cannot replace prevention.
Challenge the method before exposure spreads
The model presents old lead-containing paint proposed for dry removal. Begin with the material and task assessment, then trace the generated dust to the operator, nearby trades, floor and waste. The exposure can extend into later cleanup and hand-to-mouth transfer, even after the tool stops.
Work through the model's harm, action, management and verification decisions. Select a suitable lower-exposure method and effective controls through competent planning. A generic mask and open window do not establish a lead-safe task. The work zone, equipment, hygiene and waste arrangements need to fit together before removal starts.
After practice, explain what would show the revised method is working. The correct equipment must be installed and used, the boundary maintained, cleaning and waste controlled and people able to explain their hygiene and stop responsibilities. Where monitoring or medical surveillance is required, it supplements prevention; the crew does not continue an uncontrolled task while waiting for a later result.
Visual practice · Model practice: dry stripping the old paint
SHAREhub photographic illustration · Worker inspecting dust extraction at an industrial materials handling point. Use the written case for the exercise; this image does not prove a defect or safe system.Challenge the method before exposure spreads
The model presents old lead-containing paint proposed for dry removal. Begin with the material and task assessment, then trace the generated dust to the operator, nearby trades, floor and waste. The exposure can extend into later cleanup and hand-to-mouth transfer, even after the tool stops.
How does a refurbishment lead dust scenario develop?
A worked refurbishment pathway helps learners and site teams see how a normal-looking job becomes an exposure-control problem. Imagine a property maintenance team asked to refurbish a 1960s staircase in an occupied office. The painted handrail and balusters look sound, but historic paint layers may contain lead.
What practical controls reduce lead dust and fume?
Controls should prevent release, capture contamination close to source and stop spread. The most effective work packs are specific about tools and methods. 'Control dust' is too weak.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How does a refurbishment lead dust scenario develop?
A worked refurbishment pathway helps learners and site teams see how a normal-looking job becomes an exposure-control problem.
Imagine a property maintenance team asked to refurbish a 1960s staircase in an occupied office. The painted handrail and balusters look sound, but historic paint layers may contain lead. The first risk decision is not which mask to buy; it is whether the coating contains lead, whether the work can avoid disturbing it and whether the people nearby can be protected.
If dry sanding is chosen without testing, dust can spread to carpets, stair treads, workers' gloves, tools and the cleaner's vacuum. If heat stripping is used, fume may become the main route. If the team takes breaks in contaminated overalls, ingestion becomes a realistic exposure route even if airborne controls appear reasonable.
Stage
Competent approach
Evidence to keep
Old painted surface
Check building age, coating history, survey information and whether testing is needed before disturbance.
Pre-work information, survey/test result and assumption log.
Disturbance method
Avoid removal where possible; otherwise choose low-dust methods and prohibit uncontrolled sanding, burning or grinding.
Method statement and supervisor authorisation.
Dust or fume route
Identify inhalation, ingestion, take-home contamination and other people affected by the work area.
COSHH/lead assessment and exposure group record.
Controls
Use containment, wet/low-dust method, extraction, exclusion, suitable waste control and RPE/PPE only as part of the package.
Permit/RAMS, equipment checks and area inspection.
Hygiene and decontamination
Provide washing, clean breaks, changing, laundry/waste rules and end-of-shift tool/vehicle cleaning.
Welfare checklist and cleaning record.
Exposure monitoring
Use competent air or contamination monitoring where exposure is uncertain or significant exposure is possible.
Monitoring plan, results and interpretation.
Medical surveillance
Identify workers needing lead medical surveillance where exposure is significant and act on blood-lead trends.
Surveillance register and OH action record.
Records and learning
Record decisions, defects, results, training and lessons for similar properties.
Action tracker, lessons learned and standard update.
What practical controls reduce lead dust and fume?
Controls should prevent release, capture contamination close to source and stop spread.
The most effective work packs are specific about tools and methods. 'Control dust' is too weak. The plan should say whether wet scraping is allowed, what extraction is fitted, what vacuum class is required, how debris is bagged, how surfaces are cleaned, when RPE is worn and who checks the area before handback.
Lead fume needs special caution because hot work can create fine inhalable fume quickly. Hot cutting or burning through coated surfaces should trigger stronger planning, coating identification, removal or specialist controls before authorisation.
Control area
Good practice
Common failure
Method choice
Select low-dust or no-disturbance methods.
Dry sanding or burning without assessing lead.
On-tool extraction
Use extraction matched to the tool and contaminant.
Extraction fitted but blocked, damaged or unused.
Wet methods
Use water or paste methods where safe and suitable.
Wetting creates slurry with no waste plan.
Enclosure
Contain the work area and protect other people.
Dust migrates through open doors, ducts or voids.
Cleaning
Use suitable vacuuming and damp cleaning.
Dry sweeping or compressed air spreads dust.
Waste
Bag, label, segregate and dispose through the correct route.
Dust and debris left for general cleaners.
For the cited construction lead-paint task, HSE identifies on-tool extraction with an H- or M-class unit and RPE with APF20 as a control baseline, subject to the actual task assessment. Blasting, hot work and higher-risk industrial processes may need stronger or different controls; this is not a universal equipment specification. Check the coating, substrate, fire risks and suitability of any chemical method before work. Sources: HSE construction lead controls.
Apply the learning
A crew proposes dry stripping old paint beside a shared route and plans to sweep the debris at the end of the shift.
Decision and explanation
Hold the task and establish suitable material information, lower-exposure removal, containment, cleaning and health-control arrangements.
Lead control starts before disturbance and continues through cleanup, hygiene and waste; symptoms and later tests cannot replace prevention.
Lesson 12
Break the contamination route to the mouth and home
Control secondary contamination through usable hygiene and clothing arrangements, protecting welfare spaces and people beyond the task.
Hygiene is part of the task design
Hands, clothing, tools and phones can move contamination beyond the work zone. Lead dust on a glove may reach food or a cigarette even when inhalation exposure has been reduced. Wet cement or chemical residue inside clothing may prolong skin contact. Design a clean-to-dirty transition that people can follow in the actual workday.
Provide suitable washing, changing, storage and cleaning arrangements for the assessed hazards. Keep eating and drinking away from contamination and remove protective items in a sequence that avoids spreading material onto the skin or clean clothing. Do not take contaminated workwear home for ordinary household washing when controlled cleaning or disposal is required.
Check the interface with welfare and other workers. A cleaner should know which residues require a specific method and should not be handed an unlabelled contaminated container. The supervisor verifies that the facilities remain available after relocation or a change of shift. A hygiene instruction that depends on a locked or disconnected washing point is not an effective control.
Visual practice · Break the contamination route to the mouth and home
Actual SHAREsimulate model capture · Old lead-containing paint is dry stripped. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Hygiene is part of the task design
Hands, clothing, tools and phones can move contamination beyond the work zone. Lead dust on a glove may reach food or a cigarette even when inhalation exposure has been reduced. Wet cement or chemical residue inside clothing may prolong skin contact. Design a clean-to-dirty transition that people can follow in the actual workday.
Why is hygiene a critical lead control?
Hygiene stops lead dust being swallowed or carried away from the work area. Lead dust management often succeeds or fails at break time. A worker can wear good RPE during sanding, then swallow contamination while drinking from a dusty bottle or smoking with contaminated fingers.
How does cement dust enter or affect the body?
Cement affects the body through inhalation, eye contact, skin contact, wet cement contact, contaminated clothing and accidental ingestion from poor hygiene. The main route for dust is inhalation. The smaller the particle, the deeper it can travel into the lungs.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Why is hygiene a critical lead control?
Hygiene stops lead dust being swallowed or carried away from the work area.
Lead dust management often succeeds or fails at break time. A worker can wear good RPE during sanding, then swallow contamination while drinking from a dusty bottle or smoking with contaminated fingers. Clean welfare, hand-and-face washing, changing arrangements and contaminated clothing control are therefore central controls, not housekeeping preferences.
Take-home contamination should be challenged. Overalls, boots, gloves, hair, tools and vehicle interiors can carry dust to families and other workers. Where exposure is significant, the plan should include clean/dirty separation, laundry arrangements and rules for leaving the work area.
For lead dust, hygiene is an exposure control, not housekeeping polish: HSE employer guidance calls for separate clean and contaminated clothing storage and washing facilities. Workers wash hands and face before breaks; contaminated workwear is not taken home for domestic laundering. Check the break route and changing area during the job, not only the workface.
Hygiene control
Why it matters
Verification
Clean welfare
Prevents ingestion during breaks.
Welfare inspection and rest-area cleanliness.
Hand and face washing
Removes contamination before eating, drinking or smoking.
Facilities available and used.
No food, drink or smoking in contaminated areas
Prevents direct ingestion.
Site rules and supervisor checks.
Changing arrangements
Stops dust leaving the work area.
Clean/dirty route and storage.
Laundry controls
Avoids taking contaminated clothing home.
Laundry process and issue records.
Tool and vehicle cleaning
Prevents transfer between sites.
Cleaning checklist and visual checks.
How does cement dust enter or affect the body?
Cement affects the body through inhalation, eye contact, skin contact, wet cement contact, contaminated clothing and accidental ingestion from poor hygiene.
The main route for dust is inhalation. The smaller the particle, the deeper it can travel into the lungs. Respirable dust is not always obvious, so a lack of visible clouds does not prove exposure is controlled.
Skin contact is equally important. Cement powder and wet cement can get inside gloves, boots, sleeves and knee areas. Once trapped, it stays against the skin and can cause burns or dermatitis.
Ingestion is usually from poor hygiene: contaminated hands, dust on food, smoking with dusty fingers or drinking in contaminated areas. Welfare facilities and clean/dirty separation are therefore part of the control system.
Breathing dust from mixing, cutting, drilling or sweeping.
Wet methods, extraction, segregation and RPE.
Skin contact
Dry powder or wet cement on hands, arms, knees or legs.
Gloves, clothing, washing and skin checks.
Eye contact
Dust or wet splash into eyes.
Goggles or face protection and eyewash.
Ingestion
Dust transferred from hands to mouth.
Hygiene, no eating in dusty areas and handwashing.
Secondary exposure
Dust on clothing, tools, vehicles or welfare areas.
Cleaning, separation and decontamination.
Apply the learning
Workers remove dusty gloves and eat in the work area while contaminated coveralls are carried into the welfare cabin.
Decision and explanation
Re-establish suitable separation, washing, changing and controlled clothing arrangements before the task continues.
Control secondary contamination through usable hygiene and clothing arrangements, protecting welfare spaces and people beyond the task.
Lesson 13
Distinguish exposure monitoring from health surveillance
Monitoring and surveillance support prevention and response; neither overrides current control failure or removes confidentiality obligations.
Different evidence answers different questions
Exposure monitoring helps assess what people may breathe or otherwise encounter and whether controls are effective. It needs a suitable strategy, competent methods and interpretation for the task. A single area reading does not automatically represent every worker or the most demanding conditions. Control checks remain necessary between measurement exercises.
Health surveillance looks for relevant work-related health effects where the conditions for it apply. It is selected and managed with appropriate occupational-health or medical input; it does not mean every worker receives the same annual test. Lead can involve specific statutory medical surveillance and biological monitoring arrangements distinct from ordinary symptom reporting.
Protect confidentiality and act through the right roles. Managers need information about fitness, restrictions and required improvements, while detailed clinical records remain under appropriate medical arrangements. A satisfactory previous result does not clear a new uncontrolled exposure. If findings suggest control failure, review the work and prevent further exposure while the competent response is arranged.
Visual practice · Distinguish exposure monitoring from health surveillance
SHAREhub photographic illustration · Local extraction and chemical containers at a workplace assessment station. Use the written case for the exercise; this image does not prove a defect or safe system.Different evidence answers different questions
Exposure monitoring helps assess what people may breathe or otherwise encounter and whether controls are effective. It needs a suitable strategy, competent methods and interpretation for the task. A single area reading does not automatically represent every worker or the most demanding conditions. Control checks remain necessary between measurement exercises.
When is exposure monitoring needed and what can it prove?
Monitor where needed to show control is adequate, demonstrate compliance or resolve uncertainty; define the question first and use a competent, representative strategy. Measurement strategy boundary. HSE G409 and BS EN 689:2018 support a competent inhalation-exposure strategy: define the decision, substance and relevant fraction; identify comparable work and similar exposure groups; select a validated method and reference period; record task and control conditions; and interpret uncertainty.
When is health surveillance required?
Provide suitable surveillance when the legal and risk criteria are met; it must detect relevant adverse change early enough to protect workers and trigger control action. Health surveillance is not automatic for every chemical and it is not general wellbeing screening. It is indicated where an identifiable disease or adverse health effect is linked to exposure, workplace conditions make it reasonably likely, and valid techniques can detect it and reduce harm; specified substances/processes can have additional requirements.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
When is exposure monitoring needed and what can it prove?
Monitor where needed to show control is adequate, demonstrate compliance or resolve uncertainty; define the question first and use a competent, representative strategy.
Measurement strategy boundary. HSE G409 and BS EN 689:2018 support a competent inhalation-exposure strategy: define the decision, substance and relevant fraction; identify comparable work and similar exposure groups; select a validated method and reference period; record task and control conditions; and interpret uncertainty. Neither document replaces COSHH, COSHH NI or the current EH40 entry, and a single result does not clear unobserved people, tasks or shifts.
Exposure measurement strategy sources and limits
Source
Operational use
Boundary
HSE G409 Exposure measurement air sampling
Define the purpose before sampling; use competent advice, a suitable method and enough task information to interpret the result.
GB guidance. NI users should apply any useful technical method through COSHH NI and the HSENI route.
BS EN 689:2018
Provides a voluntary strategy for testing inhalation exposure against occupational exposure limit values, including grouping and measurement planning.
Use the current edition competently. It does not replace legal assessment, current EH40 limits, skin-route assessment or immediate action on visible control failure.
Provide suitable surveillance when the legal and risk criteria are met; it must detect relevant adverse change early enough to protect workers and trigger control action.
Health surveillance is not automatic for every chemical and it is not general wellbeing screening. It is indicated where an identifiable disease or adverse health effect is linked to exposure, workplace conditions make it reasonably likely, and valid techniques can detect it and reduce harm; specified substances/processes can have additional requirements. A competent occupational-health route should determine the scheme and escalation.
Health surveillance and biological monitoring separation
Activity
Purpose
Record and boundary
Skin surveillance
Detect relevant dermatitis or sensitisation early and review exposure/control.
Health record and individual confidential result; trained responsible person or OH route as appropriate.
Respiratory surveillance
Detect relevant respiratory change for work with respiratory sensitisers or other identified risk.
Competent scheme with symptom escalation; do not wait for severe disease.
Medical surveillance
Meet specific requirements where appointed-doctor or other medical oversight applies.
Check substance/process and legal route; do not generalise to all COSHH work.
Biological monitoring
Measure uptake or effect marker for a suitable substance.
Not the same as surveillance; handle consent, criteria and confidential interpretation.
Management learning
Use collective, anonymised findings to test controls and act on trends.
Managers do not need personal diagnoses or full clinical records.
Individual adverse result
Protect the person, review exposure and controls, and follow clinical/OH advice.
Surveillance does not make continued exposure acceptable.
Lead has specific medical surveillance expectations where exposure is significant.
HSE guidance identifies lead as a hazard where medical surveillance may be legally required. Blood-lead monitoring is used because lead absorbed into the body circulates in blood and can build up over time. Results need competent occupational-health interpretation and confidential handling.
The employer needs enough information to manage exposure, but not unnecessary diagnosis detail. The useful management output is whether a worker is fit for the lead work, whether restrictions or removal from exposure are needed, whether controls need urgent review, and what action is required for the exposure group.
HSE defines significant exposure through airborne exposure above half the lead limit, substantial ingestion risk or relevant skin exposure; HSENI gives the corresponding NI route. Use the relevant appointed-doctor or employment-medical-adviser arrangement for statutory medical surveillance. Blood-lead monitoring shows absorbed lead from all routes and must trigger control review rather than be treated as proof a dusty method is acceptable.
Element
Purpose
Management action
Baseline assessment
Confirms suitability and records starting point where required.
Arrange before significant exposure starts.
Blood-lead monitoring
Checks absorbed dose over time.
Review result trends and exposure controls.
Appointed doctor route
Provides competent medical surveillance where the law requires it.
Use HSE-appointed doctor requirements where applicable.
Removal or restriction
Protects workers where levels or medical advice require action.
Remove from exposure and investigate controls.
Health record
Employer-held record of surveillance status, not confidential clinical notes.
Keep secure and separate from casual HR records.
Medical record
Clinical information held by occupational-health professionals.
Do not demand unnecessary medical detail.
Significant exposure is not the only medical-surveillance gateway. In GB, CLAW regulation 10(1) also covers blood or urinary lead at or above the concentrations specified in regulation 10(2), measured during assessment or employment, and certification by the relevant doctor. The scheme must use an HSE-appointed doctor or employment medical adviser as applicable; a routine screening service is not a substitute. For NI use its separate CLAW instrument and HSENI medical-surveillance route, including the result and doctor-certification gateways. Sources: HSE L132 control of lead at work; HSENI lead and medical surveillance.
Apply the learning
A supervisor proposes continuing dusty lead removal because last year’s health checks were satisfactory.
Decision and explanation
Control the current exposure and use the appropriate monitoring and medical process to inform further action.
Monitoring and surveillance support prevention and response; neither overrides current control failure or removes confidentiality obligations.
Lesson 14
Respond to symptoms and exposure incidents
Respond promptly and use appropriate clinical and occupational-health support; do not expose someone again to test a theory.
Act promptly without trying to diagnose the person
A report of wheeze, breathing difficulty, skin irritation, a chemical splash or other exposure needs the planned response. Protect the person from further exposure, obtain suitable first aid and medical help as indicated, and provide reliable product and task information. Do not ask someone to repeat the task to prove their symptoms are work related.
Supervisors can recognise patterns and trigger referral; they do not diagnose occupational asthma, dermatitis or lead poisoning. Symptoms can have several causes and some serious effects develop without an early obvious warning. Appropriate occupational-health and clinical arrangements assess the person, while competent workplace assessment reviews exposure and controls.
Keep reporting supportive and specific. Record the task, material, method, controls and circumstances through authorised arrangements without spreading private medical detail. Review whether other people could be affected and whether the same failed control remains in use. Returning the person to the same exposure before the competent decision can make the problem worse.
Visual practice · Respond to symptoms and exposure incidents
Actual SHAREsimulate model capture · An isocyanate coating is applied beside other trades. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Act promptly without trying to diagnose the person
A report of wheeze, breathing difficulty, skin irritation, a chemical splash or other exposure needs the planned response. Protect the person from further exposure, obtain suitable first aid and medical help as indicated, and provide reliable product and task information. Do not ask someone to repeat the task to prove their symptoms are work related.
What symptoms should trigger action?
Symptoms should be treated as a possible control failure until competent review says otherwise. Wheeze, chest tightness, breathlessness, cough or a work-related pattern need prompt reporting and clinical or occupational-health assessment. Remove the worker from further exposure until competent advice is obtained and investigate controls.
What health surveillance is needed?
Health surveillance helps detect early signs of occupational asthma and dermatitis. HSE guidance for isocyanate-exposed workers highlights respiratory health surveillance, including lung function testing and questionnaires, and skin surveillance where dermatitis risk exists. Surveillance should start early for new workers and continue periodically.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What symptoms should trigger action?
Symptoms should be treated as a possible control failure until competent review says otherwise.
Wheeze, chest tightness, breathlessness, cough or a work-related pattern need prompt reporting and clinical or occupational-health assessment. Remove the worker from further exposure pending competent advice and investigate controls. HSE - Isocyanates in construction.
Chest tightness — Possible asthma symptom. Report, record exposure and refer to OH/medical route.
Wheeze or breathlessness — Could indicate respiratory sensitisation. Remove from exposure pending advice.
Persistent cough — May be work-related respiratory sign. Review exposure tasks and surveillance.
Flu-like shivers after spraying — HSE flags this as a possible early sign. Investigate controls and health route.
Symptoms worse after work or at night — Work pattern may be missed during shift. Ask timing questions in surveillance.
Skin rash/dermatitis — Skin sensitisation or irritant exposure possible. Review gloves, hygiene and skin surveillance.
What health surveillance is needed?
Health surveillance helps detect early signs of occupational asthma and dermatitis.
HSE guidance for isocyanate-exposed workers highlights respiratory health surveillance, including lung function testing and questionnaires, and skin surveillance where dermatitis risk exists. Surveillance should start early for new workers and continue periodically. See HSE - Health surveillance in motor vehicle repair.
Health surveillance does not replace exposure control. If surveillance finds symptoms, the correct response is to protect the worker and investigate exposure, not simply repeat the test later.
Surveillance element
Purpose
Evidence
Baseline questionnaire
Records starting respiratory/skin status.
OH health record.
Early follow-up
Detects early sensitisation pattern.
6-week/6-month style review where applicable.
Annual review
Ongoing detection and trend.
Lung function and questionnaire record.
Skin checks
Identify dermatitis or sensitisation.
Skin surveillance record.
Referral route
Escalates symptoms quickly.
OH referral and exposure review.
What should trigger action or escalation?
Action should be based on exposure evidence, symptoms, surveillance results and control failure.
Use HSE lead health-effects guidance to check the material, exposure route and task response. An unknown coating, uncontrolled dust or suspected absorbed exposure requires a competent hold and escalation decision before routine work resumes.
The table gives practical examples, evidence expectations and common decision points so the section can be used for learning, supervision, audit and review.
Trigger
Possible meaning
Response
Worker symptoms after lead work
Possible exposure or unrelated illness needing assessment.
Remove from exposure if needed and signpost OH/medical advice.
Blood-lead trend rising
Controls or hygiene may be failing.
Review task, exposure group and controls.
Suspension or restriction advice
Continued exposure may be unsafe.
Follow appointed doctor/OH advice and investigate.
Unexpected monitoring result
Exposure higher than assessed.
Stop or redesign task and retest.
Contaminated welfare
Ingestion pathway exists.
Clean, segregate and retrain.
Poor reporting trust
Workers may hide symptoms or avoid surveillance.
Review culture, communication and job-security concerns.
Suspected acute poisoning needs urgent medical assessment rather than the routine OH queue. Call 999 for unconsciousness, severe breathing difficulty or another life-threatening emergency, and use the local urgent-care service for urgent non-emergency advice. Do not enter an unsafe atmosphere to attempt an unplanned rescue. Give clinicians the substance, task and exposure timing without delaying care. Sources: NHS poisoning.
Apply the learning
A coating applicator reports wheeze after work and is told to try the next batch to confirm the connection.
Decision and explanation
Prevent further relevant exposure and follow the planned first-aid, medical or occupational-health referral and control-review process.
Respond promptly and use appropriate clinical and occupational-health support; do not expose someone again to test a theory.
Lesson 15
Store, clean and dispose safely
Keep identification and exposure controls through storage, cleaning and waste; use competent material-specific arrangements for uncertain residues.
Hazardous substance controls continue after application
Storage should maintain identification, compatibility, containment and secure access. Check the product and site assessment before mixing or decanting; incompatible materials can react, and a familiar cleaning product is not automatically suitable for every residue. Protect ignition-sensitive operations through the relevant fire and dangerous-substance arrangements.
Waste includes residues, contaminated packaging, absorbents and protective items. Classify and manage it through the appropriate site-nation route and competent advice. Mixing an uncertain residue into a general skip can expose handlers and spread contamination. Store and label the waste safely while arranging a suitable authorised transfer.
Prepare for leaks and splashes before the work starts. People need to know when to withdraw, whom to alert and what actions they are trained and equipped to take. An untrained worker should not enter an uncontrolled atmosphere or attempt a chemical neutralisation. Verify cleanup and the restored control system before restart rather than treating disappearance of the visible liquid as proof of safety.
Visual practice · Store, clean and dispose safely
SHAREhub photographic illustration · Closed pipework and vessels in a UK chemical processing plant. Use the written case for the exercise; this image does not prove a defect or safe system.Hazardous substance controls continue after application
Storage should maintain identification, compatibility, containment and secure access. Check the product and site assessment before mixing or decanting; incompatible materials can react, and a familiar cleaning product is not automatically suitable for every residue. Protect ignition-sensitive operations through the relevant fire and dangerous-substance arrangements.
How should chemicals be stored and segregated?
Chemicals should be stored in labelled compatible containers, segregated by hazard, protected from damage and supported by spill, fire and emergency arrangements. Storage is not just housekeeping. Poor storage can turn normal chemical use into fire, toxic release, uncontrolled reaction, environmental pollution or exposure during clean-up.
What emergency arrangements are needed for chemicals?
Plan for the credible release, eye or skin contact, fire and incompatible mixing before the work begins. Stop the task and move people away from an uncontrolled release. Call 999 for serious injury, toxic-gas release, fire or an incident beyond site control.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should chemicals be stored and segregated?
Chemicals should be stored in labelled compatible containers, segregated by hazard, protected from damage and supported by spill, fire and emergency arrangements.
Storage is not just housekeeping. Poor storage can turn normal chemical use into fire, toxic release, uncontrolled reaction, environmental pollution or exposure during clean-up. Chemical stores should be designed around compatibility, ventilation, containment, access control, temperature, ignition control and emergency access.
Incompatible chemicals should be separated so that leaks, container failures or mistaken mixing do not create dangerous reactions. Acids and alkalis, oxidisers and flammables, water-reactive substances and water, and chemicals that release toxic gases when mixed should be clearly controlled.
Stock should be managed. Old chemicals, unlabelled containers, decanted bottles, damaged drums and excess quantities all increase risk. A chemical register should show what is present, where it is kept, who owns it and whether the SDS and assessment are current.
Storage and compatibility controls
Storage issue
Why it matters
Good practice
Labelling
Workers need to identify contents and hazards quickly.
Keep original labels or approved workplace labels on all containers.
Segregation
Incompatible substances may react if mixed.
Separate acids, alkalis, oxidisers, flammables and toxics as required.
Containment
Leaks can spread, reach drains or contact other chemicals.
Use bunds, trays and suitable cabinets.
Ventilation
Vapours can accumulate and create inhalation or fire risk.
Provide suitable natural or mechanical ventilation.
Ignition control
Flammable vapours may ignite.
Control hot work, electrical equipment, static and smoking.
Access control
Untrained people may misuse or move chemicals.
Restrict stores and keep issue controls.
Stock rotation
Old or degraded chemicals can become unstable or unknown.
Use stock checks, expiry dates and disposal routes.
What emergency arrangements are needed for chemicals?
Plan for the credible release, eye or skin contact, fire and incompatible mixing before the work begins.
Stop the task and move people away from an uncontrolled release. Call 999 for serious injury, toxic-gas release, fire or an incident beyond site control. Do not send untrained people into a plume or improvise chemical neutralisation. First aid depends on the substance and current clinical advice; provide responders with the product identity, SDS and exposure details. A competent person should verify containment, isolation, communication and restart conditions.
Apply the learning
Unlabelled coating residue is proposed for the general skip and a cleaner is asked to use an unspecified solvent on the spill.
Decision and explanation
Hold the handling, identify the material and use the assessed cleanup, compatibility and waste arrangements.
Keep identification and exposure controls through storage, cleaning and waste; use competent material-specific arrangements for uncertain residues.
Lesson 16
Coordinate and verify the whole work zone
A relevant change triggers review when it occurs; current physical controls and shared understanding determine readiness.
Make the method visible in other trades’ plans
The area supervisor should know which tasks generate dust, vapour, mist or contamination and how they affect neighbours. Sequence or separate incompatible work and communicate controlled zones, cleaning and re-entry conditions. An isolated assessment stored in one subcontractor's folder does not coordinate a shared construction space.
Before starting, compare the method with the workface: actual product, quantity, application, extraction, protection, washing, waste and nearby people. Ask workers to show the checks and explain what stops the task. Demonstrating understanding is stronger evidence than a signature beneath technical wording that nobody can use.
Plan for maintenance and change. Extraction filters, hoses, cleaning equipment and personal equipment need the appropriate checks and servicing. A new formulation, different tool, relocated work area or missing welfare facility can invalidate the assessment. Give the team a clear way to hold the task and get the competent decision without pressure to improvise.
Visual practice · Coordinate and verify the whole work zone
Actual SHAREsimulate model capture · An isocyanate coating is applied beside other trades. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Make the method visible in other trades’ plans
The area supervisor should know which tasks generate dust, vapour, mist or contamination and how they affect neighbours. Sequence or separate incompatible work and communicate controlled zones, cleaning and re-entry conditions. An isolated assessment stored in one subcontractor's folder does not coordinate a shared construction space.
What training supports assessment and control of hazardous substances?
Training should be layered so everyone understands basic precautions, higher-risk workers understand task controls and supervisors can verify exposure control. General awareness is suitable for people who may encounter hazardous substances but do not carry out complex assessments. It should explain hazard symbols, labels, SDS basics, routes of entry, hygiene, spill reporting, storage, PPE/RPE limits and when to stop work.
What records show hazardous substance health risks are controlled?
Records should show that risks were assessed, controls were selected, people were informed and the controls remain effective. Records should support safe work, not bury people in paperwork. A useful COSHH record explains the task, substance, exposure route, control standard, training, monitoring, health surveillance and review triggers.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What training supports assessment and control of hazardous substances?
Training should be layered so everyone understands basic precautions, higher-risk workers understand task controls and supervisors can verify exposure control.
General awareness is suitable for people who may encounter hazardous substances but do not carry out complex assessments. It should explain hazard symbols, labels, SDS basics, routes of entry, hygiene, spill reporting, storage, PPE/RPE limits and when to stop work.
Task-specific training is needed for people who mix, spray, cut, sand, weld, clean, decant, maintain, dispose of or work near hazardous substances. It should cover the actual COSHH assessment, control settings, LEV use, RPE, gloves, waste, emergency procedures and health surveillance signs.
Supervisors and managers need deeper training because they approve tasks, allocate resources, check field conditions and respond to monitoring results or symptoms. COSHH assessors need enough competence and authority to gather information, observe tasks, interpret SDS and WEL information, select controls and know when to seek specialist help.
Role-specific competence evidence
Role and learning
Practice on the actual task
Competence evidence and record
Assessor and reassessment trigger
Workers: identify task exposure
Check substance, label, actual use and controls; stop an unknown or failed-control task.
Observed task check and reporting decision.
Supervisor rechecks after product, task or symptom change.
Supervisors: test the assessment
Walk the real task, routes and controls; check ventilation, skin and ingestion exposure and emergency action.
Observed control check and corrected assessment.
Competent assessor reviews after process or incident change.
Occupational hygienists: assess exposure
Select air, surface or biological monitoring where appropriate; interpret WEL and uncertainty in task context.
Sampling strategy, rationale and interpreted results.
Technical peer reviews after new result or process change.
Occupational health: run surveillance
Select proportionate health surveillance for relevant disease risk and protect confidential results.
Qualified protocol, referral and action record.
Clinical lead reviews after findings or guidance change.
Managers: assure prevention
Fund substitution and engineering controls, set owners and verify that exposure stays controlled.
Current COSHH assessment, action closure and worker feedback.
Accountable lead reviews after new material or trend.
Record observed task decisions, assessor and reassessment trigger; attendance alone does not establish competence.
What records show hazardous substance health risks are controlled?
Records should show that risks were assessed, controls were selected, people were informed and the controls remain effective.
Records should support safe work, not bury people in paperwork. A useful COSHH record explains the task, substance, exposure route, control standard, training, monitoring, health surveillance and review triggers. It should be available to the people who need to use it.
SDS should be kept current and accessible, but SDS alone is not evidence of assessment. The strongest evidence is the combination of documents and field proof: workers using the controls, LEV performing properly, RPE face-fit completed, health surveillance acted on and actions closed.
Some records need long-term retention where health effects may emerge later, especially exposure and health surveillance records. Retention periods depend on the regulatory context and type of exposure.
Retention and confidentiality are different controls. The employer keeps the COSHH assessment, control and exposure evidence, and a limited employer health record where surveillance is required. Confidential clinical notes and test data remain medical records held in confidence by the occupational-health professional; managers should receive only the functional or control information they lawfully need.
COSHH records retention and confidentiality matrix
Record
Minimum or trigger
Owner, access and action
Assessment significant findings
GB regulation 6(4) and NI regulation 6(4): record significant findings where the employer has five or more employees. Recording remains good practice for smaller employers.
Employer-controlled task record; make the relevant controls and stop conditions available to workers and representatives.
Control examination and test
GB regulation 9(4) and the parallel NI duty: keep the suitable record for at least five years from the date it was made.
Employer control record, including defects, corrective action and release. This is distinct from daily user checks.
General exposure monitoring
GB regulation 10(5) and the parallel NI duty: at least five years where the record is not personal or identifiable exposure.
Employer or competent-hygiene record; retain method, task conditions, result, uncertainty, interpretation and action.
Identifiable personal exposure monitoring
Keep for at least 40 years from the date of the last entry where the monitoring record is representative of, or relates to, identifiable employees' personal exposure.
Secure employer exposure record. Give workers appropriate result information and preserve identity, method and task context.
Employer health record under COSHH
Keep for at least 40 years from the date of the last entry. Record identity, exposure/surveillance dates and the outcome or fitness/action needed, not confidential clinical findings.
Employer-controlled with restricted access. Offer the worker a copy when they leave and follow the applicable enforcing-authority route if the business ceases.
Confidential medical record
Clinical notes and test data are not the employer health record and are not an employer-retention file. They are retained under professional and applicable medical-record requirements.
Held in medical confidence by the occupational-health professional. Employer access needs the lawful written-consent route; transfer securely to a new occupational-health provider, not through line management.
Worker access, transfer and business cessation
Provide access to the employer health record and a copy on leaving where appropriate; preserve continuity when occupational-health providers change; follow the regulator route for records if the employer ceases trading.
Plan this before provider or business closure. Do not disclose another worker's data or move confidential clinical records into ordinary HR files.
How can a management system sustain effective decisions?
Give each hazard or support route an owner, a control, a check and a response to failure.
Connect material inventory, task controls, equipment tests, exposure findings, confidential surveillance and corrective action. An owner should sample actual work and corrective actions, not accept a policy or certificate as evidence that the controls work.
The free GB regulator guide HSE Managing for health and safety (HSG65) explains a plan–do–check–act approach: assign controls and owners, involve workers, check work as done, and correct failures. For Northern Ireland, use HSENI risk assessment guidance for the local duty. A certificate alone does not demonstrate that a control works.
Apply the learning
The product and application area change, but the subcontractor says the old signed assessment must remain valid until the annual review.
Decision and explanation
Review the changes before use and verify the revised controls, interfaces and briefing at the actual workface.
A relevant change triggers review when it occurs; current physical controls and shared understanding determine readiness.
Lesson 17
Capstone: the three-task refurbishment
Every relevant exposure route and task interface must be addressed; a strong control for one hazard cannot cancel another unresolved critical gap.
Resolve each exposure route before release
At fictional Mill Lane, a crew proposes mixing dry bags, spraying a two-part coating and stripping an old painted beam on the same shift. The washing point is temporarily unavailable, the coating area overlaps an electrical task and the paint survey does not cover the beam. Do not let one tidy risk assessment conceal three unresolved workface decisions.
Map the common controls and the task-specific ones. Separation and welfare may support several activities, while lead identification, coating respiratory protection and cement contact prevention need their own evidence. Decide which competent person can resolve each gap and maintain a clear hold on the affected task. A good control for one substance does not automatically protect against another.
Before recommending restart, verify the actual arrangements and brief everyone affected, including cleaners and waste handlers. Keep monitoring and health arrangements in their proper supporting roles. The defensible recommendation connects material information, method, effective controls and a practical response to change; it does not rest on a bundle of supplier sheets or course scores.
Visual practice · Capstone: the three-task refurbishment
SHAREhub photographic illustration · Local extraction and chemical containers at a workplace assessment station. Use the written case for the exercise; this image does not prove a defect or safe system.Resolve each exposure route before release
At fictional Mill Lane, a crew proposes mixing dry bags, spraying a two-part coating and stripping an old painted beam on the same shift. The washing point is temporarily unavailable, the coating area overlaps an electrical task and the paint survey does not cover the beam. Do not let one tidy risk assessment conceal three unresolved workface decisions.
How should a COSHH health-risk assessment be carried out?
A COSHH assessment should identify hazardous substances, assess exposure, decide controls, record findings, implement actions and review effectiveness. Start by creating a substance and process inventory. Include what is bought, what is generated and what appears during cleaning, maintenance, waste handling and emergencies.
What should a COSHH risk register include?
A COSHH risk register should connect each substance or exposure group to the task, exposure route, controls, health surveillance need, owner and review trigger. A useful register is not just a list of products. It should tell managers which exposures matter most, where controls are critical, which workers are in similar exposure groups and what evidence should be checked.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should a COSHH health-risk assessment be carried out?
A COSHH assessment should identify hazardous substances, assess exposure, decide controls, record findings, implement actions and review effectiveness.
Start by creating a substance and process inventory. Include what is bought, what is generated and what appears during cleaning, maintenance, waste handling and emergencies. Then observe the task. The person doing the work often knows where dust escapes, where splashes occur and where the written procedure is unrealistic.
The assessment should be task-based. A single product may need different assessments for brushing, spraying, decanting, heating, cleaning and waste handling. Similarly, a single dust hazard may need different controls for cutting, drilling, sweeping, bag emptying and filter changing.
The output should be a usable control plan. It should state what controls are required before work, during work and after work; who checks them; what training is required; what records are kept; and what triggers review.
A COSHH risk register should connect each substance or exposure group to the task, exposure route, controls, health surveillance need, owner and review trigger.
A useful register is not just a list of products. It should tell managers which exposures matter most, where controls are critical, which workers are in similar exposure groups and what evidence should be checked. It should also flag high-consequence substances such as carcinogens, mutagens, asthmagens and substances with workplace exposure limits.
COSHH risk register prompts
Register field
What to record
Why it matters
Substance or exposure source
Product name, generated contaminant, process source, hazardous properties and physical form.
Prevents the register being limited to purchased chemicals while missing dusts, fumes, mists and biological agents.
Task and exposed group
Who does the work, who is nearby, how often, for how long and during which normal or abnormal activities.
Supports proper health surveillance, monitoring strategy and prioritisation.
Critical controls
Substitution, enclosure, LEV, wet methods, hygiene, RPE, PPE, safe systems, storage, waste and emergency arrangements.
Shows which controls prevent exposure and which need inspection, maintenance or testing.
Assurance evidence
LEV test dates, airflow checks, exposure monitoring, face-fit records, glove selection, training, audits and health surveillance outcomes.
Turns the register from a static list into a management tool.
Review triggers
New product, changed process, new SDS, illness report, monitoring result, LEV defect, incident, contractor change or regulatory update.
Keeps COSHH controls current as work changes.
Apply the learning
Three activities share an area, with missing washing, an unassessed coating zone and uncertain old paint.
Decision and explanation
Hold affected work, resolve each material and exposure decision, verify the coordinated controls and brief all affected people before release.
Every relevant exposure route and task interface must be addressed; a strong control for one hazard cannot cancel another unresolved critical gap.
Lesson 18
Create a practical control-improvement action
Meaningful improvement links the task and exposure to a specific effective control, clear ownership and physical verification.
Ask for evidence that the person can use
Choose an anonymised or fictional substance task and state its full sequence. Identify the person doing it, others nearby and the routes of exposure. Select one improvement that moves the control earlier in the process: substitution, reduced release, source capture, separation or a better contamination transition.
Turn the idea into a verifiable action with an owner and follow-up. For example, confirm that the revised application method has been assessed, that extraction works at the actual source or that washing remains available after a welfare move. Explain what would keep the task held and who can authorise a competent revised decision.
This course supports recognition and applied assessment questions. It does not authorise specialist exposure assessment, medical decisions, respiratory-equipment selection or hazardous-material work beyond the learner's competence. Use the workplace tools as prompts within your organisation's process; the fictional exercises are not live assessments, medical records or signed operating instructions.
Visual practice · Create a practical control-improvement action
Actual SHAREsimulate model capture · Wet cement and unassessed chemicals reach the skin. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Ask for evidence that the person can use
Choose an anonymised or fictional substance task and state its full sequence. Identify the person doing it, others nearby and the routes of exposure. Select one improvement that moves the control earlier in the process: substitution, reduced release, source capture, separation or a better contamination transition.
How can a management system sustain effective decisions?
Give each hazard or support route an owner, a control, a check and a response to failure. Keep procurement, assessment, source controls, health surveillance and emergency decisions connected through named owners and review after change. An owner should sample actual work and corrective actions, not accept a policy or certificate as evidence that the controls work.
What should each role learn and demonstrate?
Learning must match the decisions people make, from recognising danger to checking that controls work. Briefings should tell people how to act, but attendance alone does not show competence. Assess the real decision or task, record who assessed it and revisit after a material change, failed control or incident.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How can a management system sustain effective decisions?
Give each hazard or support route an owner, a control, a check and a response to failure.
Keep procurement, assessment, source controls, health surveillance and emergency decisions connected through named owners and review after change. An owner should sample actual work and corrective actions, not accept a policy or certificate as evidence that the controls work.
The free GB regulator guide HSE Managing for health and safety (HSG65) explains a plan–do–check–act approach: assign controls and owners, involve workers, check work as done, and correct failures. For Northern Ireland, use HSENI risk assessment guidance for the local duty. A certificate alone does not demonstrate that a control works.
What should each role learn and demonstrate?
Learning must match the decisions people make, from recognising danger to checking that controls work.
Briefings should tell people how to act, but attendance alone does not show competence. Assess the real decision or task, record who assessed it and revisit after a material change, failed control or incident. A local authorisation is task-specific; no universal external certificate is implied.
On a small screen, scroll this table sideways to read all columns.
Role-level learning and competence evidence
Role and learning
Demonstration and assessor
Record and reassessment trigger
Sprayer
Demonstrate booth/RPE and clearance response; supervisor observes.
Task observation; repeat on defect.
Supervisor
Verify extraction and maintenance; hygienist assesses.
Test log; review on process change.
Occupational health
Set and interpret surveillance; clinician reviews.
Confidential records and trend feedback; reassess after symptom.
Apply the learning
An action says only “buy more PPE” without identifying the substance, task or exposure route.
Decision and explanation
Define the actual task and exposure and choose a proportionate source-control improvement with an owner and verification step.
Meaningful improvement links the task and exposure to a specific effective control, clear ownership and physical verification.
Match the nine hazard symbols
End-of-course revision · Drag each symbol to its hazard name, or use the menu on each card with touch or keyboard. This is practice alongside the separate final assessment.
Acute toxicity
Corrosive
Explosive
Flammable
Gas under pressure
Harmful / irritant
Hazardous to the environment
Oxidising
Serious health hazard
Match all nine symbols, then check your choices.
Need the reference table?Chemical hazard pictograms · examples and checksOptional reference · all nine symbols · does not change assessment requirements
READ THE LABEL · UNDERSTAND THE TASK
Recognise the symbol. Read the full label. Assess the actual task.
Examples illustrate possible uses of a symbol, not the classification of every formulation. A product can carry several pictograms. Check its current label, hazard statements and matching safety data sheet (SDS).
CLP/GHS hazard pictograms: meanings and illustrative examples
Pictogram and hazard
What it can mean
Example and question before work
ExplosiveGHS01
Explosion, blast or projection hazards; also certain self-reactive substances and organic peroxides.
Example: Certain fireworks or reactive chemical products.Ask: Does the authorised task account for impact, heat and the product’s stability limits?
FlammableGHS02
Can ignite; also used for certain self-heating, pyrophoric or water-reactive hazards.
Example: Petrol or some solvent-based products.Ask: What could release vapour or ignite it during this task, including nearby work?
OxidisingGHS03
Can cause or intensify fire; some strong oxidisers present an explosion hazard.
Example: Oxygen or certain oxidising chemicals.Ask: What incompatible materials and contamination must the assessed storage and connection keep apart?
Gas under pressureGHS04
Pressurised gas may burst if heated; refrigerated gas can cause cold burns.
Example: Compressed-gas cylinders.Ask: Have the gas identity, cylinder, connection and pressure or temperature hazards been checked?
CorrosiveGHS05
May damage metals, cause severe skin burns or cause serious eye damage; read the stated hazard.
Example: Certain drain cleaners, acids or alkalis.Ask: Which contact and splash routes must be prevented in this actual handling or dilution task?
Acute toxicityGHS06
Can be toxic or fatal after short exposure through the stated route.
Example: Methanol or certain pesticide products.Ask: Which exposure routes and emergency arrangements does this product’s information identify?
Harmful / irritantGHS07
May indicate harmful acute toxicity, irritation, skin sensitisation, drowsiness or dizziness; also ozone-layer hazards.
Example: Some detergents or cleaning products.Ask: What do the hazard statements say? Do not dismiss this as a harmless or mild product.
Serious health hazardGHS08
Can indicate cancer, genetic or reproductive harm, organ damage, respiratory sensitisation or aspiration hazard.
Example: Petrol or some sensitising chemical products.Ask: Which particular health effect is stated, and how does the task prevent the relevant exposure?
Hazardous to the environmentGHS09
Hazardous to aquatic life, potentially with long-lasting effects.
Example: Certain pesticides, biocides or fuels.Ask: How will the assessed arrangements prevent release to drains, water or soil?
Read beyond the picture · Open a prompt to compare the explanation.
Is the exclamation mark the same as the chest-starburst symbol?
No. The two symbols communicate different groups of hazards. Read the actual hazard statements: skin sensitisation and respiratory sensitisation are not interchangeable, and neither symbol specifies the complete task controls.
Does a bottle with no pictogram prove the task is safe?
No. Work may generate hazardous dust, fume or mist, and exposure depends on the task. Resolve missing or conflicting identification before use. A pictogram is not a compatibility chart or a complete workplace risk assessment.
Which information turns recognition into a useful work decision?
Match the product and SDS revision. Read the hazard statements and relevant SDS sections for handling, storage, exposure control, emergencies and reactivity together. Then check the actual task assessment and controls. A safety data sheet is not itself a COSHH assessment.