Safe use and maintenance of construction equipment · learning reader
Free training · Approx. 1h 50m–2h 40m · estimated self-paced learning, including activities and assessment.
Public teaching is free without an account. A free learner account is required for confirmed LMS assessment, completion and certificate records. See the full course outline and access routes.
Teaching and applied cases for accessible study. The interactive course records assessed completion.
Lesson 1
Plan the whole equipment task
Assess the full lifecycle and choose a machine and method that can be set up, used, cleared and maintained safely.
Read the workface decision
Equipment risk follows people through delivery, installation, adjustment, use, intervention and removal. A suitable production process can become unsafe when a person reaches into a blockage or works beneath an unsupported component. Plan those tasks before choosing the machine. The manufacturer's intended use, the real material and the surrounding work area all matter to selection.
Visual practice · Plan the whole equipment task
SHAREhub photographic illustration · Stopped pillar drill with guard in a UK engineering workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Equipment risk follows people through delivery, installation, adjustment, use, intervention and removal. A suitable production process can become unsafe when a person reaches into a blockage or works beneath an unsupported component. Plan those tasks before choosing the machine. The manufacturer's intended use, the real material and the surrounding work area all matter to selection.
How should work equipment be controlled across its life?
Control starts with need and specification, continues through purchase or hire, acceptance, installation, use, inspection, maintenance and change, and ends with safe decommissioning or disposal. Treat each transfer as an evidence gate. A check at purchase does not cover later deterioration, modification, relocation, new attachments, changed users or a different environment.
See the actual construction-model example
The saw is shown with its guard and connected extraction. The proposed next cut defeats both barriers because the material is awkward. The blade can cut, draw in or eject material, while dust can harm the operator and people nearby. A guard that obstructs a proposed cut is a reason to review equipment, support or method, not permission to lift it out of the way. The hand-feeding technique and the whole cutting setup must suit the machine.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should work equipment be controlled across its life?
Control starts with need and specification, continues through purchase or hire, acceptance, installation, use, inspection, maintenance and change, and ends with safe decommissioning or disposal.
Treat each transfer as an evidence gate. A check at purchase does not cover later deterioration, modification, relocation, new attachments, changed users or a different environment.
Select. Critical question: Is this the right equipment and control concept?; Evidence: Specification and risk decision.
Accept and install. Critical question: Is identity, condition and setup proven?; Evidence: Acceptance and commissioning.
Use and maintain. Critical question: Does it remain safe in real work?; Evidence: Checks, defects, maintenance and inspection.
Change or retire. Critical question: Has risk changed or energy been removed?; Evidence: Change review or decommission record.
How should suitable equipment be selected?
Select equipment that is suitable for the intended task, people, environment, loads and conditions, with risks controlled by design and compatible guards, controls, attachments and information.
Prefer eliminating hazardous operations or choosing safer equipment before adding procedural controls. Include cleaning, maintenance, access, foreseeable misuse and emergency recovery in the selection decision.
Task and capacity. Question: Can it do the work within maker limits?; Reject or hold when: Duty or attachment is unclear.
People. Question: Can intended users operate and maintain it safely?; Reject or hold when: Access, reach or competence is unsuitable.
Environment. Question: Is it suitable for wet, dusty, explosive or public conditions?; Reject or hold when: Protection or compatibility is unproven.
Lifecycle. Question: Can it be inspected, isolated and maintained?; Reject or hold when: Safe intervention cannot be achieved.
What should a purchase or hire specification contain?
Specify the real task, materials, environment, users, foreseeable interventions, required safeguards, information, inspection and maintenance support, and the evidence needed before acceptance.
Do not procure from a catalogue description alone. Ask how the equipment will be installed, guarded, isolated, cleaned, maintained, moved, integrated and withdrawn from service.
Intended use. Procurement evidence: Duty, workpiece, environment and interfaces.; Acceptance gate: Matches actual work.
Safeguards. Procurement evidence: Guarding and control philosophy.; Acceptance gate: No accessible danger zone in assessed use.
Support. Procurement evidence: Instructions, parts, maintenance and competence needs.; Acceptance gate: Organisation can sustain safe use.
Market route. Procurement evidence: Applicable conformity and supplier documents.; Acceptance gate: Correct market and product sector.
How should equipment be accepted before first use?
Verify identity, condition, documentation, correct market route where relevant, intended use, guards, controls, accessories, installation needs, inspection status and support before the equipment enters service.
Record deviations and quarantine anything damaged, incomplete, unexpectedly modified or unsupported. Delivery paperwork alone is not a commissioning record.
Identity and specification. Evidence: Model, serial or asset reference and intended duty.; Hold point: Mismatch or unknown origin.
Condition and completeness. Evidence: Damage check, guards, accessories and instructions.; Hold point: Missing or damaged safety part.
Legal and support route. Evidence: Applicable supplier documents and service support.; Hold point: Wrong market route or no critical information.
Workplace readiness. Evidence: Installation, risk assessment and training plan.; Hold point: Site prerequisites absent.
What should installation and commissioning prove?
Commissioning should prove that the equipment is stable, correctly assembled and located, connected to safe services, guarded, controlled, isolated, documented and able to perform the intended task without creating uncontrolled risk.
Test safeguards and abnormal responses without exposing people. Integration with other machines, extraction, traffic routes or control systems needs a whole-system review.
Physical installation. Question: Is it stable, secure and safely accessible?; Evidence: Installation inspection.
Safeguards and controls. Question: Do guards, interlocks and stops work as intended?; Evidence: Functional test.
Energy and isolation. Question: Can all sources be safely controlled?; Evidence: Isolation test and diagram.
Operational handover. Question: Are method, competence and maintenance ready?; Evidence: Commissioning and release record.
The saw is shown with its guard and connected extraction. The proposed next cut defeats both barriers because the material is awkward. The blade can cut, draw in or eject material, while dust can harm the operator and people nearby. A guard that obstructs a proposed cut is a reason to review equipment, support or method, not permission to lift it out of the way. The hand-feeding technique and the whole cutting setup must suit the machine.
Choose the right saw and work support, keeping dangerous parts adequately guarded and using the correct feeding or handling aids. Manufacturer-specific adjustment and maintenance must be done from the appropriate safe isolated state. The required stopping and braking performance is part of equipment suitability; a motor that has been switched off can still leave a blade moving. Training should cover both routine cuts and the point where an unusual cut must be held for another method.
Identify the material and dust. Wood dust requires suitable extraction at source; cutting silica-containing products needs its own appropriate dust-control method and equipment. A connected hose is not proof of capture: hood position, airflow, filter condition, hose blockage and waste collection affect performance. Plan safe collection and cleaning rather than dry sweeping or blowing dust into the work area. Where residual risk requires RPE, select and manage it appropriately; it does not replace guarding or effective engineering controls.
Evidence to establish at the workface
Reject the proposed removal of protection and select a suitable cutting method, machine and support that allow the task within the intended safeguards.
Apply the learning
A saw is selected for its cutting capacity, but nobody considers setting up, clearing offcuts or cleaning it.
Decision and explanation
Assess the full lifecycle and choose a machine and method that can be set up, used, cleared and maintained safely.
Equipment risk follows people through delivery, installation, adjustment, use, intervention and removal. A suitable production process can become unsafe when a person reaches into a blockage or works beneath an unsupported component. Plan those tasks before choosing the machine. The manufacturer's intended use, the real material and the surrounding work area all matter to selection.
Lesson 2
Recognise machinery harm pathways
Keep access controlled and identify movement, stored energy and the authorised isolation method before intervention.
Read the workface decision
Dangerous movement includes drawing-in, entanglement, crushing, shearing, cutting and ejection. The motor need not be running for gravity, pressure, springs or loaded material to move. Describing the mechanism helps choose the barrier: guarding prevents access during operation, while intervention needs a safe working condition that addresses all relevant energy and movement.
Visual practice · Recognise machinery harm pathways
Actual SHAREsimulate model capture · A mixer jam is reached through an open guard. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Investigate 1: Mixer
The mixer is visible. Its jam and unsecured stored energy are stated in the fictional case. Pressing stop alone is not the case’s secured-energy arrangement: prevent access until the required isolation and release checks are complete.
Investigate 2: Temporary cable route
A cable links equipment in this area. Identify the relevant energy sources from reliable equipment and task information; a cable in a picture cannot establish isolation or prove that mechanical energy has been released.
Investigate 3: Bench work area
Nearby work shares the equipment area. Plan who controls the intervention and restart, and how other people are kept clear. Do not infer that a general stop instruction controls the mixer’s stored energy.
Read the workface decision
Dangerous movement includes drawing-in, entanglement, crushing, shearing, cutting and ejection. The motor need not be running for gravity, pressure, springs or loaded material to move. Describing the mechanism helps choose the barrier: guarding prevents access during operation, while intervention needs a safe working condition that addresses all relevant energy and movement.
Which hazards must the equipment assessment cover?
Assess mechanical contact and ejection together with electrical, pressure, thermal, chemical, ergonomic, noise, vibration, fire, explosion, mobility, stability and work-at-height hazards that the equipment or task can create. Consider normal production, foreseeable abnormal events, clearing blockages, tool change, cleaning, testing, breakdown, maintenance and recovery after a stop. People nearby can be exposed even when they do not operate the equipment.
See the actual construction-model example
Pressing stop can halt normal operation while leaving a mixer capable of moving. Another person may restart it, a control may be activated accidentally, or stored mechanical energy may be released when the jam clears. Raised components, springs, hydraulic pressure and material under load can move without the motor running. An open guard gives the worker access to those hazards at exactly the point where unexpected movement can trap a hand or body.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Which hazards must the equipment assessment cover?
Assess mechanical contact and ejection together with electrical, pressure, thermal, chemical, ergonomic, noise, vibration, fire, explosion, mobility, stability and work-at-height hazards that the equipment or task can create.
Consider normal production, foreseeable abnormal events, clearing blockages, tool change, cleaning, testing, breakdown, maintenance and recovery after a stop. People nearby can be exposed even when they do not operate the equipment.
Mechanical. Examples: Crushing, shearing, cutting, entanglement, drawing-in, ejection.; Control question: Can access or energy be prevented?
Energy. Examples: Electricity, pressure, gravity, heat, stored motion.; Control question: Can every source be isolated and dissipated?
Exposure. Examples: Dust, fume, noise, vibration, substances.; Control question: Which separate regime and source control apply?
Context. Examples: Mobility, stability, falls, traffic, fire.; Control question: What environment and interface change the risk?
Pressing stop can halt normal operation while leaving a mixer capable of moving. Another person may restart it, a control may be activated accidentally, or stored mechanical energy may be released when the jam clears. Raised components, springs, hydraulic pressure and material under load can move without the motor running. An open guard gives the worker access to those hazards at exactly the point where unexpected movement can trap a hand or body.
Prevent routine access to dangerous parts through suitable guarding and a method that avoids jams where practicable. Where clearing is necessary, use the equipment-specific safe process performed by authorised competent people. Identify and isolate all energy sources, secure against reconnection and make stored energy safe through appropriate dissipation, restraint or support. Confirm the safe state before intervention. Do not rely on a workmate holding the stop button or standing by the plug.
Some equipment has an engineered clearing or maintenance mode, but it must be suitable for the actual intervention and used exactly as designed; it is not permission to bypass an interlock. Coordinate contractors and multiple workers so one person cannot remove another’s protection inadvertently. After clearing, restore guards and safety devices, account for tools and people and hand the machine back through the agreed sequence. Investigate recurring jams rather than treating repeated dangerous intervention as normal production.
Evidence to establish at the workface
Use the equipment-specific clearing method with competent authorisation, effective isolation, secured reconnection control and identified stored-energy measures.
Apply the learning
A worker describes a jammed mixer as harmless because its motor has stopped.
Decision and explanation
Keep access controlled and identify movement, stored energy and the authorised isolation method before intervention.
Dangerous movement includes drawing-in, entanglement, crushing, shearing, cutting and ejection. The motor need not be running for gravity, pressure, springs or loaded material to move. Describing the mechanism helps choose the barrier: guarding prevents access during operation, while intervention needs a safe working condition that addresses all relevant energy and movement.
Lesson 3
Select tools that fit the material and person
Compare suitable methods and select maintained equipment that controls total exposure and can be used safely.
Read the workface decision
The lowest purchase price or emission figure does not establish the safest process. Tool suitability affects duration, posture, dust, noise, vibration and control of the workpiece. Involve users and competent advice where the selection is uncertain. Assess the whole task and achievable control performance, including whether prefabrication or another process can remove the intrusive work.
Visual practice · Select tools that fit the material and person
SHAREhub photographic illustration · Stopped pillar drill with guard in a UK engineering workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
The lowest purchase price or emission figure does not establish the safest process. Tool suitability affects duration, posture, dust, noise, vibration and control of the workpiece. Involve users and competent advice where the selection is uncertain. Assess the whole task and achievable control performance, including whether prefabrication or another process can remove the intrusive work.
What counts as work equipment and use?
Work equipment includes machinery, appliances, apparatus, tools and installations used at work, while use includes starting, stopping, programming, setting, transporting, repairing, modifying, maintaining, servicing and cleaning. A hand tool, office appliance, machine line, scaffold component, ladder, lift truck or process installation may be work equipment. The applicable controls depend on the actual use and risk, not the label or purchase value.
See the actual construction-model example
The worker uses a poorly maintained breaker for long periods and reports tingling fingers. Hand-arm vibration can damage nerves and circulation and affect grip and fine control. Symptoms are a reason to act promptly, not an expected sign of hard work to ignore. The tool also creates noise and dust and may impose awkward force or posture; controlling one exposure does not establish that the whole breaking task is safe.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What counts as work equipment and use?
Work equipment includes machinery, appliances, apparatus, tools and installations used at work, while use includes starting, stopping, programming, setting, transporting, repairing, modifying, maintaining, servicing and cleaning.
A hand tool, office appliance, machine line, scaffold component, ladder, lift truck or process installation may be work equipment. The applicable controls depend on the actual use and risk, not the label or purchase value.
Tool or appliance. Why it is in scope: Used to perform work.; Decision: Suitability and safe use.
Machine or installation. Why it is in scope: Creates mechanical or other energy hazards.; Decision: Guarding, controls and lifecycle evidence.
Cleaning or adjustment. Why it is in scope: It is use under Provision and Use of Work Equipment Regulations (PUWER).; Decision: Safe state and competent method.
Transport or modification. Why it is in scope: Can change condition or risk.; Decision: Planning, inspection and change control.
Which general PUWER duties must be checked?
For the actual task, check suitability, condition, safeguards, controls, isolation, inspection, maintenance, competent users and safe intervention. A power press used for working cold metal needs a separate applicability check for GB PUWER Part IV or the corresponding Northern Ireland provisions, including exclusions; general PUWER controls alone are not a release decision.
In Great Britain the baseline map is principally PUWER 1998 regulations 4 to 24, with separate Part IV power-press provisions in regulations 31 to 35. Northern Ireland has its own PUWER 1999 route. Check the actual press, use, safeguards and legal scope with a competent specialist; this matrix sets no universal examination period, test method or authority to operate.
Decision group
Practical question
Evidence or hold
Suitability and condition
Is it fit for this task and environment and kept safe?
Specification, assessment, maintenance and applicable inspection.
People and access
Who may use, set, clean, inspect or maintain it?
Information, training, restriction and supervision.
Danger and controls
Can anyone reach danger or be hit by ejection, rupture or uncontrolled movement?
Safeguards, controls, tests and stop criteria.
Place and communication
Is it stable, lit and understood?
Installation, workspace, markings and warnings.
Intervention and release
Can it be isolated and restored safely?
Energy control, planned tests and named handback.
How do workplace-use duties differ from product-supply duties?
PUWER controls equipment provided or used at work; product-supply rules govern placing products on a market. A CE, UK Conformity Assessed (UKCA) or CE and UK Northern Ireland (UKNI) route does not by itself prove workplace suitability, correct installation or safe use.
Choose the GB or NI market route and the product sector before relying on conformity documentation. Separately complete workplace selection, risk assessment, guarding, installation, competence, inspection and maintenance decisions.
Who will use it and for what? Workplace-use route: PUWER and other workplace law.; Product-supply route: Not the main market decision.
May this product be placed on this market? Workplace-use route: Does not answer safe-use question.; Product-supply route: Current GB or NI sector rules.
Was it modified or assembled? Workplace-use route: Reassess safe use.; Product-supply route: May create manufacturer obligations.
The worker uses a poorly maintained breaker for long periods and reports tingling fingers. Hand-arm vibration can damage nerves and circulation and affect grip and fine control. Symptoms are a reason to act promptly, not an expected sign of hard work to ignore. The tool also creates noise and dust and may impose awkward force or posture; controlling one exposure does not establish that the whole breaking task is safe.
Avoid or reduce the breaking task first, for example through design, precast openings or a suitable lower-exposure mechanical method. Where hand-held tools remain necessary, choose effective lower-vibration equipment for the actual material and maintain the tool, consumable and anti-vibration features. A tool that performs poorly may increase both vibration and the time needed. Anti-vibration gloves are not a reliable substitute for controlling vibration at source.
Assess actual exposure from every relevant tool used in the day. Trigger time means time in effective contact with operating vibrating equipment, not the whole booked shift, while several tools contribute to the same person’s exposure. Manufacturer emission figures need task-relevant interpretation; do not allocate an arbitrary universal safe number of minutes. Review work patterns after stronger controls, provide information and indicated health surveillance, and obtain occupational-health advice on symptoms and restrictions. Protect medical confidentiality while making the necessary task changes.
Evidence to establish at the workface
Maintain effective tools and consumables, assess representative vibration and actual trigger times across all tools, and reduce exposure as far as reasonably practicable.
Apply the learning
A lightly powered breaker takes much longer on a hard floor and requires heavy force from the user.
Decision and explanation
Compare suitable methods and select maintained equipment that controls total exposure and can be used safely.
The lowest purchase price or emission figure does not establish the safest process. Tool suitability affects duration, posture, dust, noise, vibration and control of the workpiece. Involve users and competent advice where the selection is uncertain. Assess the whole task and achievable control performance, including whether prefabrication or another process can remove the intrusive work.
Lesson 4
Prepare a stable, usable work area
Stop setup and provide suitable support, stability, workholding, space and separation before use.
Read the workface decision
The machine, material and operator form one working arrangement. Unstable equipment and poorly supported stock can defeat a guard or force a person into the danger zone. Check lighting, access, material travel, power and extraction connections, waste and nearby people. A productive layout reduces the temptation to bypass protection when handling awkward material.
Visual practice · Prepare a stable, usable work area
Actual SHAREsimulate model capture · The operator proposes removing saw protection. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
The machine, material and operator form one working arrangement. Unstable equipment and poorly supported stock can defeat a guard or force a person into the danger zone. Check lighting, access, material travel, power and extraction connections, waste and nearby people. A productive layout reduces the temptation to bypass protection when handling awkward material.
What about stability, lighting and working space?
Secure or stabilise equipment as needed, provide lighting adequate for the work and its hazards, and arrange enough safe space for use, access, cleaning and maintenance without exposing people to moving parts or traffic. A machine that is suitable in one place may be unsafe on a different floor, outdoors or beside another operation. Check foundations, restraints, access, visibility, shadows, glare, weather and adjacent activity with competent input where necessary.
Evidence to establish at the workface
Reject the proposed removal of protection and select a suitable cutting method, machine and support that allow the task within the intended safeguards.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What about stability, lighting and working space?
Secure or stabilise equipment as needed, provide lighting adequate for the work and its hazards, and arrange enough safe space for use, access, cleaning and maintenance without exposing people to moving parts or traffic.
A machine that is suitable in one place may be unsafe on a different floor, outdoors or beside another operation. Check foundations, restraints, access, visibility, shadows, glare, weather and adjacent activity with competent input where necessary.
Reject the proposed removal of protection and select a suitable cutting method, machine and support that allow the task within the intended safeguards.
Apply the learning
A saw stands on loose blocks while long stock overhangs a pedestrian route.
Decision and explanation
Stop setup and provide suitable support, stability, workholding, space and separation before use.
The machine, material and operator form one working arrangement. Unstable equipment and poorly supported stock can defeat a guard or force a person into the danger zone. Check lighting, access, material travel, power and extraction connections, waste and nearby people. A productive layout reduces the temptation to bypass protection when handling awkward material.
Lesson 5
Use the guarding hierarchy
Stop and change the equipment, material support or method so effective guarding remains in place.
Read the workface decision
Guarding needs to prevent foreseeable access without creating a new hazard or being easily defeated. The correct solution depends on the equipment and operation; a course cannot supply generic opening dimensions or a homemade guard design. Information and PPE support the residual risk after stronger protection, rather than legitimising contact with an exposed dangerous part.
Visual practice · Use the guarding hierarchy
SHAREhub photographic illustration · Stopped pillar drill with guard in a UK engineering workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Guarding needs to prevent foreseeable access without creating a new hazard or being easily defeated. The correct solution depends on the equipment and operation; a course cannot supply generic opening dimensions or a homemade guard design. Information and PPE support the residual risk after stronger protection, rather than legitimising contact with an exposed dangerous part.
What is the guarding hierarchy?
Prevent access to dangerous parts with fixed guards where practicable, then use other guards or protection devices, then jigs, holders or push-sticks, with information, instruction, training, supervision and PPE only for remaining risk. A guard must be suitable, effective, maintained, not easily bypassed and not create a new hazard. Guard design and safe distance are equipment-specific engineering decisions, not values to copy from this guide.
Evidence to establish at the workface
Observe the proposed cut from a safe position and check whether support, guard adjustment and hand positions remain within the accepted machine method. Check the dust-control indicator and capture arrangement against the system instructions, inspecting hose condition, collection and maintenance status without exposing anyone.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What is the guarding hierarchy?
Prevent access to dangerous parts with fixed guards where practicable, then use other guards or protection devices, then jigs, holders or push-sticks, with information, instruction, training, supervision and PPE only for remaining risk.
A guard must be suitable, effective, maintained, not easily bypassed and not create a new hazard. Guard design and safe distance are equipment-specific engineering decisions, not values to copy from this guide.
Priority
Control
Boundary
1
Fixed guard.
Use where practicable and compatible with necessary access.
2
Other guard or protection device.
Must fail or act to a safe condition as designed.
3
Jig, holder, push-stick or similar aid.
Keeps the person from danger where higher controls cannot fully apply.
4
Information, training, supervision and PPE.
Residual layer, not a substitute for practicable safeguarding.
What if equipment or material is very hot or cold?
Where contact with very hot or cold equipment or process material could injure someone, prevent exposure through design, guarding, insulation, separation, safe handling and clear information appropriate to the task.
Include residual heat or cold after stopping, cleaning and maintenance. The actual process and manufacturer data determine temperatures and protections; this guide sets no generic threshold.
Operation. Control question: Can a person touch a dangerous surface or material?; Hold point: Guard, insulate or separate before use.
Shutdown. Control question: Does residual temperature remain?; Hold point: Wait, verify and warn under the local method.
Intervention. Control question: Will opening expose stored thermal energy?; Hold point: Plan competent isolation and protection.
How are ejection, rupture and other specified hazards controlled?
Prevent or contain foreseeable ejection of parts or material, rupture, fire, explosion and unintended release at source; protect people through suitable engineering and operating controls selected for the actual process.
Do not assume a guard against contact also contains a failed workpiece or pressure release. Assess material, speed, energy, failure mode, surrounding people and connected equipment. Pressure systems, dangerous substances and explosive atmospheres may need separate legal routes.
Ejected workpiece or fragment. Check: Workholding, enclosure and safe direction.; Stop or escalate: Loose work or failed enclosure.
Rupture or release. Check: Integrity, pressure and containment assessment.; Stop or escalate: Leak, crack or unknown rating.
Fire or explosion. Check: Ignition, fuel and atmosphere interaction.; Stop or escalate: Unassessed process or failed protection.
How should interlocks and protective devices be managed?
If a guard interlock or protective device fails, move clear, use only the trained safe stopping action available from a safe position, warn others and report it; do not reach in, repeat the failed test, bypass or adjust the device. Quarantine affected equipment until safe isolation, competent repair, representative safeguard testing and named operating-owner release are recorded.
Do not tape, wedge, bridge, override or programme around a device to maintain production. Diagnostic or test modes require a designed safe method, restricted authority and equipment-specific controls.
Device functions normally. Meaning: Only evidence for the tested safeguard function.; Response: Continue within assessed use.
Intermittent trip. Meaning: Possible fault or changing condition.; Response: Stop, quarantine and diagnose safely.
Bypass found. Meaning: Safeguard no longer reliable.; Response: Isolate as needed and escalate.
Reset restores operation. Meaning: Does not explain cause.; Response: Investigate before release.
Observe the proposed cut from a safe position and check whether support, guard adjustment and hand positions remain within the accepted machine method. Check the dust-control indicator and capture arrangement against the system instructions, inspecting hose condition, collection and maintenance status without exposing anyone.
Apply the learning
The guard prevents an awkward cut and the supervisor suggests holding it up for one pass.
Decision and explanation
Stop and change the equipment, material support or method so effective guarding remains in place.
Guarding needs to prevent foreseeable access without creating a new hazard or being easily defeated. The correct solution depends on the equipment and operation; a course cannot supply generic opening dimensions or a homemade guard design. Information and PPE support the residual risk after stronger protection, rather than legitimising contact with an exposed dangerous part.
Lesson 6
Controls, interlocks and emergency stops
Take the affected equipment out of use and arrange competent diagnosis and safeguard verification under a designed method.
Read the workface decision
Start, stop, emergency-stop and protective functions have different purposes. A reset does not explain why a safeguard failed or establish safe isolation for intervention. Report an intermittent fault as a control-system problem. Diagnostic work needs its own competence, authority and safeguards; it is not an extension of normal production performed with protection defeated.
Visual practice · Controls, interlocks and emergency stops
Actual SHAREsimulate model capture · A mixer jam is reached through an open guard. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Start, stop, emergency-stop and protective functions have different purposes. A reset does not explain why a safeguard failed or establish safe isolation for intervention. Report an intermittent fault as a control-system problem. Diagnostic work needs its own competence, authority and safeguards; it is not an extension of normal production performed with protection defeated.
What makes starting, stopping and operating controls safe?
Controls should be identifiable, appropriate, reachable from a safe position, protected against unintended operation where needed, and arranged so starting occurs only through deliberate action and stopping brings equipment to a safe state. The operator must understand normal stop, emergency response, reset and restart. A reset should not itself create hazardous movement unless the assessed control design specifically provides safe conditions.
Evidence to establish at the workface
Verify the safe state before intervention, using suitable support or restraint where necessary; never substitute a held stop button or informal lookout.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What makes starting, stopping and operating controls safe?
Controls should be identifiable, appropriate, reachable from a safe position, protected against unintended operation where needed, and arranged so starting occurs only through deliberate action and stopping brings equipment to a safe state.
The operator must understand normal stop, emergency response, reset and restart. A reset should not itself create hazardous movement unless the assessed control design specifically provides safe conditions.
Control function
Expected behaviour
Verification
Start
Deliberate action with danger zone clear.
Commissioning and user check.
Normal stop
Brings operation to intended safe state.
Functional test.
Mode or selector
Controls access and authority for the chosen mode.
Restricted setting and instruction.
Restart
No unexpected movement after interruption or reset.
Cause and safe-state check.
Which markings and warnings are needed?
Provide markings and warnings that make safety-critical controls, limits, hazards and actions clear to the people who use or work around the equipment; keep them legible and consistent with the actual machine and instructions.
Signs and alarms support, but do not replace, guarding or effective control. Check language, accessibility, visibility, audible signal in the real environment and whether a worker knows what action an alarm requires. Do not invent a rating or limit.
Control labels. Use: Identify correct start, stop, mode and isolation route.; Failure signal: Ambiguous or worn label.
Safety markings. Use: Show actual equipment limits or prohibited conditions.; Failure signal: Missing, inconsistent or unverifiable value.
Warning device. Use: Prompt the defined response.; Failure signal: Alarm unnoticed, misunderstood or routinely ignored.
How must starting, stopping and control systems behave?
Starting and significant changes in operating condition should require deliberate action; normal stop must take precedence over start, and controls and systems must be positioned and designed so foreseeable failure does not create danger.
A stop button is not an isolation point. Check the whole machine and connected line, mode selection, reset, unexpected restart and what happens after power loss or return. Have a competent controls specialist define and verify safety functions for the actual machine.
Start or change. Expected decision: Deliberate command in the selected safe mode.; Hold point: Unexpected start or unclear mode.
Normal stop. Expected decision: Reaches the intended safe state.; Hold point: Continued hazardous motion or unreliable response.
Emergency stop. Expected decision: Additional rapid stop where appropriate.; Hold point: Not a replacement for guard or isolation.
Control failure. Expected decision: Risk remains controlled by design.; Hold point: Unverified fault response or connected-system state.
What is an emergency stop for?
An emergency stop is an additional rapid protective action, not normal stopping, guarding or isolation. After use, move clear, warn and report, exclude the area, control connected plant and do not reset, enter or investigate until authorised people apply the equipment-specific isolation; the named operating owner releases only after cause, repair, safeguard and controlled-test evidence is accepted.
Releasing an emergency stop does not prove a safe state or permit restart. Keep people clear and preserve the event state; emergency command governs any live emergency, while competent maintainers and control specialists govern isolated investigation and the operating owner governs return to service.
When is it used? Answer: For an emergency requiring rapid stop.; Boundary: Not the routine production stop.
What does it do? Answer: Acts with priority as designed.; Boundary: May not remove every energy source.
Does it isolate? Answer: Not necessarily.; Boundary: Apply the full isolation procedure.
Can it be reset and run? Answer: Only after cause and safe state are verified.; Boundary: Named return-to-service authority governs.
Verify the safe state before intervention, using suitable support or restraint where necessary; never substitute a held stop button or informal lookout.
Apply the learning
An interlock trips intermittently and a colleague proposes taping the switch in place to diagnose it during production.
Decision and explanation
Take the affected equipment out of use and arrange competent diagnosis and safeguard verification under a designed method.
Start, stop, emergency-stop and protective functions have different purposes. A reset does not explain why a safeguard failed or establish safe isolation for intervention. Report an intermittent fault as a control-system problem. Diagnostic work needs its own competence, authority and safeguards; it is not an extension of normal production performed with protection defeated.
Lesson 7
Pre-use checks and defect reporting
Keep the machine out of use and raise the defect with the site equipment controller and supplier.
Read the workface decision
Pre-use checks provide current information about features the user can properly assess. They are not a demand to dismantle unfamiliar machinery or test dangerous failures. The user needs a clear defect route and protection from pressure to continue. Hiring equipment does not remove the responsibilities of those providing or controlling it at the workface.
Visual practice · Pre-use checks and defect reporting
SHAREhub photographic illustration · Stopped pillar drill with guard in a UK engineering workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Pre-use checks provide current information about features the user can properly assess. They are not a demand to dismantle unfamiliar machinery or test dangerous failures. The user needs a clear defect route and protection from pressure to continue. Hiring equipment does not remove the responsibilities of those providing or controlling it at the workface.
What belongs in a pre-use check?
A pre-use check should cover visible condition, correct setup and attachment, guards and protective devices, controls, cables or hoses, stability, work area and any equipment-specific indicator identified by the assessment or manufacturer. A quick user check is not a substitute for a formal inspection. Its content and record depend on risk, equipment and the organisation's system; do not invent a universal checklist or sign-off interval.
Evidence to establish at the workface
Reject the proposed removal of protection and select a suitable cutting method, machine and support that allow the task within the intended safeguards.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What belongs in a pre-use check?
A pre-use check should cover visible condition, correct setup and attachment, guards and protective devices, controls, cables or hoses, stability, work area and any equipment-specific indicator identified by the assessment or manufacturer.
A quick user check is not a substitute for a formal inspection. Its content and record depend on risk, equipment and the organisation's system; do not invent a universal checklist or sign-off interval.
Check
Example observation
Action
Condition
Damage, wear, leakage or loose part.
Stop and report if safety may be affected.
Safeguards
Guard or device missing, open or defeated.
Do not use; quarantine.
Controls
Start, stop or indication abnormal.
Hold pending competent decision.
Area and task
Wrong attachment, unstable base or people exposed.
Correct conditions before start.
How should equipment be monitored during use?
Use equipment only for the assessed task and conditions, keep safeguards in place, maintain exclusion and stability, watch for abnormal sound, movement, heat, vibration, leakage or control response, and stop before investigating a change.
Do not reach through a guard, defeat a device, clear a blockage live or rely on familiarity. A change in material, attachment, operator, environment or production method can invalidate the starting decision.
Unexpected movement or ejection. Immediate response: Stop from a safe position.; Next decision: Quarantine and investigate.
Guard or device changes state. Immediate response: Stop work and keep clear.; Next decision: Competent safeguarding review.
Abnormal noise, heat or vibration. Immediate response: Stop without close diagnosis.; Next decision: Maintenance assessment.
Task or environment changes. Immediate response: Pause the job.; Next decision: Reassess method and suitability.
What should happen when work finishes?
Stop the equipment through the defined sequence, leave moving and stored energy controlled, clean without entering danger, record defects or restrictions, and hand back the equipment and area in a known state.
Completion is not permission for maintenance. Any intervention requiring access to danger or stored energy needs its own isolation and authorised method.
Normal stop. Expected state: Movement ceases through intended control.; Evidence: User observation.
Secure and clean. Expected state: No unintended access, restart or unsafe residue.; Evidence: Task completion check.
Report. Expected state: Defects and restrictions are visible to the next user.; Evidence: Tag, log or handover.
Hand back. Expected state: Named owner accepts status.; Evidence: Release or continued hold.
Reject the proposed removal of protection and select a suitable cutting method, machine and support that allow the task within the intended safeguards.
Apply the learning
The guard is cracked when the machine arrives from hire, although the delivery sheet is signed.
Decision and explanation
Keep the machine out of use and raise the defect with the site equipment controller and supplier.
Pre-use checks provide current information about features the user can properly assess. They are not a demand to dismantle unfamiliar machinery or test dangerous failures. The user needs a clear defect route and protection from pressure to continue. Hiring equipment does not remove the responsibilities of those providing or controlling it at the workface.
Lesson 8
Dust, noise and ejection from cutting
Hold cutting until the guard, dust control, workholding and protection of nearby people form a working system.
Read the workface decision
One safeguard rarely controls every consequence. A contact guard may not contain a failed workpiece, and it does not automatically control airborne dust. Check the equipment's intended use, material and connected extraction. Nearby people can be exposed even when the operator is well equipped. A changed cut or room can invalidate the previous arrangement.
Compare the visible eye with its enlarged side cutaway. Locate the clear front, lens and inner rear lining before following light and visual signals.
Distinguish the protective eye surface from the internal visual pathway. What task-specific protection or workstation change does this lesson require?
educational illustration · healthy anatomy; enlarged details and teaching colours.View full detail ↗Lungs and airways in the chest
Locate the lungs, branching airways and diaphragm below them. The cutaway reveals structures normally hidden by the chest wall.
Trace the source-to-breathing-zone route in this lesson. Which change would prevent the contaminant reaching the person?
educational illustration · healthy anatomy; enlarged details and teaching colours.
Visual practice · Dust, noise and ejection from cutting
Actual SHAREsimulate model capture · The operator proposes removing saw protection. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
One safeguard rarely controls every consequence. A contact guard may not contain a failed workpiece, and it does not automatically control airborne dust. Check the equipment's intended use, material and connected extraction. Nearby people can be exposed even when the operator is well equipped. A changed cut or room can invalidate the previous arrangement.
Apply the control to this stage of work
The same principle applies to grinders, cutting benches, routing equipment and other machines where awkward work tempts users to bypass guards or extraction.
Evidence to establish at the workface
Maintain effective guarding, appropriate feed aids and safety-critical controls, including stopping performance, and isolate safely for adjustment or maintenance.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Apply the control to this stage of work
The same principle applies to grinders, cutting benches, routing equipment and other machines where awkward work tempts users to bypass guards or extraction.
Evidence to establish at the workface
Maintain effective guarding, appropriate feed aids and safety-critical controls, including stopping performance, and isolate safely for adjustment or maintenance.
Apply the learning
A saw's guard remains fitted but the extraction hose is disconnected and other trades enter the cutting area.
Decision and explanation
Hold cutting until the guard, dust control, workholding and protection of nearby people form a working system.
One safeguard rarely controls every consequence. A contact guard may not contain a failed workpiece, and it does not automatically control airborne dust. Check the equipment's intended use, material and connected extraction. Nearby people can be exposed even when the operator is well equipped. A changed cut or room can invalidate the previous arrangement.
Lesson 9
Understand inspection triggers
Confirm the inspections needed for installation and deterioration risks before use, using competent people and appropriate records.
Read the workface decision
Inspection requirements depend on the equipment and the risks from installation or deterioration. Exceptional events and major changes may also matter. The scope and frequency should follow a defensible assessment, relevant instructions and any applicable specialist regime. A sticker provides little assurance if it is not linked to the particular machine, installation and safety-critical features.
Visual practice · Understand inspection triggers
SHAREhub photographic illustration · Stopped pillar drill with guard in a UK engineering workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Inspection requirements depend on the equipment and the risks from installation or deterioration. Exceptional events and major changes may also matter. The scope and frequency should follow a defensible assessment, relevant instructions and any applicable specialist regime. A sticker provides little assurance if it is not linked to the particular machine, installation and safety-critical features.
When is a PUWER inspection needed?
When is a PUWER inspection needed? In Great Britain, inspection is required where safety depends on installation, where deterioration could cause danger, or after exceptional circumstances liable to jeopardise safety. The NI instrument is separate and must be checked for the NI workplace.
Evidence to establish at the workface
Verify the safe state before intervention, using suitable support or restraint where necessary; never substitute a held stop button or informal lookout.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
When is a PUWER inspection needed?
In Great Britain, inspection is required where safety depends on installation, where deterioration could cause danger, or after exceptional circumstances liable to jeopardise safety. The NI instrument is separate and must be checked for the NI workplace.
A reinstalled machine may need inspection before first use at the new location. Deteriorating equipment needs suitable intervals set by risk. Major modification, suspected serious damage or a substantial change of use can trigger an additional inspection. Not every item needs a formal inspection; a low-risk item may be adequately checked before use. Keep the inspection result and act on defects. HSE inspection of work equipment and HSENI PUWER 1999.
Inspection evidence follows the equipment
For GB PUWER inspection, retain the result at least until the next inspection and ensure equipment moving between undertakings has physical evidence of the last required inspection. Check scope, result, restrictions and next trigger before use. This is separate from LOLER/PSSR examination-record retention. NI uses its own PUWER route. HSE: inspection of work equipment.
Evidence to establish at the workface
Verify the safe state before intervention, using suitable support or restraint where necessary; never substitute a held stop button or informal lookout.
Apply the learning
A machine has been reassembled in a new area after transport and the team relies on the previous site's inspection.
Decision and explanation
Confirm the inspections needed for installation and deterioration risks before use, using competent people and appropriate records.
Inspection requirements depend on the equipment and the risks from installation or deterioration. Exceptional events and major changes may also matter. The scope and frequency should follow a defensible assessment, relevant instructions and any applicable specialist regime. A sticker provides little assurance if it is not linked to the particular machine, installation and safety-critical features.
Lesson 10
Plan maintenance as a separate job
Plan competent maintenance with safe access, separation, isolation and coordination of connected work.
Read the workface decision
Maintenance is non-routine work and may expose parts normally enclosed. The plan needs to protect the maintainer and everyone affected by opened guards, removed flooring, lifting or released substances. Use manufacturer information and specialist support where required. Scheduling work during a suitable shutdown can remove conflicts that are difficult to manage with warnings alone.
Visual practice · Plan maintenance as a separate job
Actual SHAREsimulate model capture · A mixer jam is reached through an open guard. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Maintenance is non-routine work and may expose parts normally enclosed. The plan needs to protect the maintainer and everyone affected by opened guards, removed flooring, lifting or released substances. Use manufacturer information and specialist support where required. Scheduling work during a suitable shutdown can remove conflicts that are difficult to manage with warnings alone.
How can maintenance itself be made safe?
Plan intervention hazards before removing guards or opening plant. Control energy, movement, height, substances, contractors and nearby operations for the whole job. Identify every energy source, bring equipment to the required state, securely isolate, prevent reconnection and release or restrain stored energy.
Evidence to establish at the workface
Prevent access to the jam and take the mixer out of use through the authorised process, keeping others from initiating movement.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How can maintenance itself be made safe?
Plan intervention hazards before removing guards or opening plant. Control energy, movement, height, substances, contractors and nearby operations for the whole job.
Identify every energy source, bring equipment to the required state, securely isolate, prevent reconnection and release or restrain stored energy. A stop command or open guard is not secure isolation. Use planned exceptional powered fault-finding only with competent specialists and designed protection. Coordinate group work and shift changes. HSE maintenance of work equipment and HSE L22 Safe use of work equipment.
At handback, account for people and tools, restore guards and devices, verify the affected functions and authorise a controlled restart. A permit is a coordination tool where the risk system requires it; it does not substitute for physical controls. Contractors need equipment identity, instructions, hazard information and a defined interface.
Evidence to establish at the workface
Prevent access to the jam and take the mixer out of use through the authorised process, keeping others from initiating movement.
Apply the learning
A maintainer is asked to replace a component while production continues around the machine.
Decision and explanation
Plan competent maintenance with safe access, separation, isolation and coordination of connected work.
Maintenance is non-routine work and may expose parts normally enclosed. The plan needs to protect the maintainer and everyone affected by opened guards, removed flooring, lifting or released substances. Use manufacturer information and specialist support where required. Scheduling work during a suitable shutdown can remove conflicts that are difficult to manage with warnings alone.
Lesson 11
Isolate all relevant energy
Keep access controlled until authorised competent people address electrical and stored mechanical energy under the equipment-specific method.
Read the workface decision
Isolation must match the actual machine and task. Electrical disconnection alone may leave gravitational, hydraulic, pneumatic, thermal or mechanical hazards. Safe restraint and release are technical decisions that need suitable equipment and verification. A worker should not learn the remaining energy by touching or disturbing the obstruction. Define the safe condition before the body enters the danger zone.
Visual practice · Isolate all relevant energy
SHAREhub photographic illustration · Stopped pillar drill with guard in a UK engineering workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Isolation must match the actual machine and task. Electrical disconnection alone may leave gravitational, hydraulic, pneumatic, thermal or mechanical hazards. Safe restraint and release are technical decisions that need suitable equipment and verification. A worker should not learn the remaining energy by touching or disturbing the obstruction. Define the safe condition before the body enters the danger zone.
How should equipment be isolated?
Identify every energy source, stop and separate the equipment, prevent reconnection or release, dissipate or restrain stored energy, verify the safe state, control the work and restore only through the authorised sequence. Electrical isolation alone may leave hydraulic, pneumatic, pressure, thermal, gravity, spring, rotational or process energy. The actual isolation points, verification method and lock-off arrangements must come from competent equipment-specific planning.
Evidence to establish at the workface
Ask the authorised person to identify every relevant energy source and how the particular mixer and loaded mechanism are made safe for this intervention. Check isolation and stored-energy controls are effective at the work point and protect everyone involved, including other shifts or contractors.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should equipment be isolated?
Identify every energy source, stop and separate the equipment, prevent reconnection or release, dissipate or restrain stored energy, verify the safe state, control the work and restore only through the authorised sequence.
Electrical isolation alone may leave hydraulic, pneumatic, pressure, thermal, gravity, spring, rotational or process energy. The actual isolation points, verification method and lock-off arrangements must come from competent equipment-specific planning.
Energy or stage
Control question
Evidence
Identify
What can move, energise, pressurise, heat or release?
Energy map and instructions.
Separate and secure
Can reconnection or release be prevented?
Isolation and lock-off record.
Dissipate or restrain
What stored energy remains?
Verified zero or safely restrained state.
Restore
Are people clear and safeguards restored?
Controlled handback and release.
How should maintenance be planned?
Plan maintenance as work in its own right: define scope, condition, isolation, access, competence, tools, parts, coordination, testing, safeguards and handback before intervention begins.
Maintain equipment in an efficient state and good repair. Where maintenance cannot be done at rest, use an equipment-specific safe method and protection designed for that task; routine production pressure never supplies the justification.
Prepare. Control: Scope, hazards, safe state and people.; Evidence: Work order or task plan.
Intervene. Control: Isolation, access, tools and coordination.; Evidence: Permit or maintenance record.
Test. Control: Controlled test with restricted exposure.; Evidence: Functional and safeguard results.
Hand back. Control: Covers, guards and settings restored.; Evidence: Named acceptance and release.
Ask the authorised person to identify every relevant energy source and how the particular mixer and loaded mechanism are made safe for this intervention. Check isolation and stored-energy controls are effective at the work point and protect everyone involved, including other shifts or contractors.
Apply the learning
A mixer is unplugged but a raised component and compacted load can still move when the jam clears.
Decision and explanation
Keep access controlled until authorised competent people address electrical and stored mechanical energy under the equipment-specific method.
Isolation must match the actual machine and task. Electrical disconnection alone may leave gravitational, hydraulic, pneumatic, thermal or mechanical hazards. Safe restraint and release are technical decisions that need suitable equipment and verification. A worker should not learn the remaining energy by touching or disturbing the obstruction. Define the safe condition before the body enters the danger zone.
Lesson 12
Clear a blockage without normalising shortcuts
Stop the shortcut, establish safe intervention and investigate the recurring fault and production pressures.
Read the workface decision
Repeated success can make an unsafe intervention feel routine while leaving its consequences unchanged. Fix both the immediate access risk and the reason the machine repeatedly jams. Material suitability, setup, maintenance and workload may all contribute. An effective system makes safe intervention practicable, with readily available isolation arrangements and clear authority to stop production.
Visual practice · Clear a blockage without normalising shortcuts
Actual SHAREsimulate model capture · A mixer jam is reached through an open guard. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Repeated success can make an unsafe intervention feel routine while leaving its consequences unchanged. Fix both the immediate access risk and the reason the machine repeatedly jams. Material suitability, setup, maintenance and workload may all contribute. An effective system makes safe intervention practicable, with readily available isolation arrangements and clear authority to stop production.
How can the hierarchy of controls guide safe work-equipment selection and use?
Remove the hazard where reasonably practicable. If it remains, consider a safer method, engineering controls and safe work arrangements before personal protective equipment for residual risk. HSE places elimination, substitution, engineering, administrative controls and personal protective equipment in that order.
Evidence to establish at the workface
Verify the safe state before intervention, using suitable support or restraint where necessary; never substitute a held stop button or informal lookout.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How can the hierarchy of controls guide safe work-equipment selection and use?
Remove the hazard where reasonably practicable. If it remains, consider a safer method, engineering controls and safe work arrangements before personal protective equipment for residual risk.
HSE places elimination, substitution, engineering, administrative controls and personal protective equipment in that order. Verify that the chosen controls work on the actual task.
ERICPD (Eliminate, Reduce including substitution, Isolate, Control, personal protective equipment (PPE), Discipline) is a SHARE decision prompt cross-mapped to HSE’s five-level hierarchy. Choose stronger feasible controls first, verify them in the actual task and record why a stronger option cannot be used. Discipline means sustaining controls through maintenance, supervision and learning.
How can the ERICPD hierarchy of controls guide safe work-equipment selection and use?
ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
ERICPD prompt
HSE relation
Actual measure
Owner, evidence and stop point
Eliminate
Elimination
Remove a hazardous equipment step by redesigning material flow, for example avoiding manual feeding into a dangerous operating zone. Assess production and foreseeable maintenance together so the design does not move the risk elsewhere.
Select equipment and a feed or handling method suited to the material, space, frequency and users. Trial a safer low-energy or automated method, checking new trapping, unexpected-start and maintenance hazards.
Engineering where physical or technical separation is feasible
Prevent access to dangerous parts through suitable guards or protective devices and control all relevant energy for maintenance. Choose the guarding design and isolation method for the actual machine, not a generic emergency-stop label.
Competent engineer verifies guard/device function and authorised maintainer establishes isolation before access. Stop if a guard is defeated, dangerous motion remains or stored energy is unproven. Basis: HSE L22 Safe use of work equipment; HSE Maintenance of work equipment
Control
Administrative or organisational controls
Restrict high-risk use and maintenance to suitable people, provide task instructions and pre-use checks, and plan safe handback. A control panel or training record does not establish that the work can be performed safely.
Personal protective equipment for residual exposure
Select task-specific eye, hearing, hand or other protection only for residual hazards after equipment controls. Check compatibility with the task; gloves may introduce entanglement risk on some rotating machinery and need a specific assessment.
Maintain equipment and protective devices, inspect when required, control modifications and learn from defects. Recheck suitability when the task, material, location or user changes.
How can the ISO 45001 hierarchy of controls guide safe work-equipment selection and use?
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").
Remove a hazardous equipment step by redesigning material flow, for example avoiding manual feeding into a dangerous operating zone. Assess production and foreseeable maintenance together so the design does not move the risk elsewhere.
Select equipment and a feed or handling method suited to the material, space, frequency and users. Trial a safer low-energy or automated method, checking new trapping, unexpected-start and maintenance hazards.
Engineering where physical or technical separation is feasible
Prevent access to dangerous parts through suitable guards or protective devices and control all relevant energy for maintenance. Choose the guarding design and isolation method for the actual machine, not a generic emergency-stop label.
Competent engineer verifies guard/device function and authorised maintainer establishes isolation before access. Stop if a guard is defeated, dangerous motion remains or stored energy is unproven. Basis: HSE L22 Safe use of work equipment; HSE Maintenance of work equipment
Control
Administrative or organisational controls
Restrict high-risk use and maintenance to suitable people, provide task instructions and pre-use checks, and plan safe handback. A control panel or training record does not establish that the work can be performed safely.
Personal protective equipment for residual exposure
Select task-specific eye, hearing, hand or other protection only for residual hazards after equipment controls. Check compatibility with the task; gloves may introduce entanglement risk on some rotating machinery and need a specific assessment.
Maintain equipment and protective devices, inspect when required, control modifications and learn from defects. Recheck suitability when the task, material, location or user changes.
Verify the safe state before intervention, using suitable support or restraint where necessary; never substitute a held stop button or informal lookout.
Apply the learning
Frequent jams have led the crew to reach past a guard after pressing stop.
Decision and explanation
Stop the shortcut, establish safe intervention and investigate the recurring fault and production pressures.
Repeated success can make an unsafe intervention feel routine while leaving its consequences unchanged. Fix both the immediate access risk and the reason the machine repeatedly jams. Material suitability, setup, maintenance and workload may all contribute. An effective system makes safe intervention practicable, with readily available isolation arrangements and clear authority to stop production.
Lesson 13
Change blades and accessories competently
Keep it out of service until a competent person confirms compatibility, condition and fitting requirements.
Read the workface decision
Physical fit does not establish safe compatibility. Speed, material, dimensions, fixing arrangements, direction and manufacturer restrictions can be critical. Accessory changes need safe isolation and relevant competence, including specific training where required. Keep the accessory identity and instructions available rather than relying on packaging that has been discarded or another site's informal practice.
Visual practice · Change blades and accessories competently
SHAREhub photographic illustration · Stopped pillar drill with guard in a UK engineering workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Physical fit does not establish safe compatibility. Speed, material, dimensions, fixing arrangements, direction and manufacturer restrictions can be critical. Accessory changes need safe isolation and relevant competence, including specific training where required. Keep the accessory identity and instructions available rather than relying on packaging that has been discarded or another site's informal practice.
What competence does each role need?
Teach and assess the task each person performs, define authority and reassess after equipment, method or performance changes. Sources: HSE maintenance of work equipment; HSE inspection of work equipment; HSE thorough examination of lifting equipment; HSE pressure systems regulations overview.
Evidence to establish at the workface
Reject the proposed removal of protection and select a suitable cutting method, machine and support that allow the task within the intended safeguards.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What competence does each role need?
Teach and assess the task each person performs, define authority and reassess after equipment, method or performance changes.
Role learning demonstration assessment and reassessment
Role
What to learn
Practical proof
Assessor and record
Reassessment trigger
New worker
Recognise damaged guards, failed stop, tags and reporting.
Demonstrates a safe stop and defect report.
Supervisor records awareness.
New machine or incident.
Operator
Know pre-use check, normal limits and hold conditions.
Shows the actual check and refuses unsafe use.
Supervisor signs machine/task scope.
New mode, defect trend or changed task.
Maintainer
Know instructions, isolation, repair, protected test and handback.
Practical task and verified energy boundary.
Engineering lead records authorisation.
New energy, component or method.
Inspector or examiner
Know relevant damage modes and legal/scheme scope.
Examines representative defects and writes a usable report.
Competent technical lead and, where needed, impartiality review.
Equipment or regime change.
Supervisor or manager
Plan intervals, hold defects, coordinate contractors and release.
Runs failed-interlock scenario with written hold and evidence.
Responsible manager samples decisions.
Repeated defect or near miss.
Safety adviser or auditor
Trace GB/NI law and source to field evidence.
Samples check, repair, test and statutory report distinction.
Reject the proposed removal of protection and select a suitable cutting method, machine and support that allow the task within the intended safeguards.
Apply the learning
A replacement accessory fits the spindle but its rating and suitability for the machine and material are unknown.
Decision and explanation
Keep it out of service until a competent person confirms compatibility, condition and fitting requirements.
Physical fit does not establish safe compatibility. Speed, material, dimensions, fixing arrangements, direction and manufacturer restrictions can be critical. Accessory changes need safe isolation and relevant competence, including specific training where required. Keep the accessory identity and instructions available rather than relying on packaging that has been discarded or another site's informal practice.
Lesson 14
Manage vibration through equipment choices
Stop the defective setup, report symptoms promptly and improve the method, maintenance and exposure controls.
Read the workface decision
Tool condition can increase vibration and extend the task. Exposure control starts with avoiding or reducing the work and selecting suitable maintained equipment. Gloves may help warmth and other hand protection needs but must not be treated as a dependable vibration control. Health symptoms require the organisation's prompt reporting and occupational-health arrangements, not a diagnosis by the supervisor.
Locate the index finger in the whole hand. The separate cutaway enlarges skin, bones, vessels and nerves; colours distinguish the structures.
Keep circulation, sensation and movement distinct. Which tool or work-method change would reduce the exposure described here?
educational illustration · healthy anatomy; enlarged details and teaching colours.
Visual practice · Manage vibration through equipment choices
Actual SHAREsimulate model capture · A damaged breaker is used for excessive trigger time. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Tool condition can increase vibration and extend the task. Exposure control starts with avoiding or reducing the work and selecting suitable maintained equipment. Gloves may help warmth and other hand protection needs but must not be treated as a dependable vibration control. Health symptoms require the organisation's prompt reporting and occupational-health arrangements, not a diagnosis by the supervisor.
What should be checked before vibrating work starts?
Confirm the task, person, equipment and expected exposure match the assessment, then inspect the tool or vehicle and the controls that keep magnitude and time down. For HAV, check tool, bit/disc, handles, mountings, workpiece support, planned trigger time and any other HAV task that day. For WBV, check route, ground, tyres, seat and suspension, load and expected jolts.
Evidence to establish at the workface
Check the real breaking method, tool condition, consumable and material and compare achievable lower-exposure alternatives rather than purchasing from one emission number. Review representative trigger-time evidence for each worker’s complete tool day, including changes, overtime and uncertainty in the exposure estimate.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What should be checked before vibrating work starts?
Confirm the task, person, equipment and expected exposure match the assessment, then inspect the tool or vehicle and the controls that keep magnitude and time down.
For HAV, check tool, bit/disc, handles, mountings, workpiece support, planned trigger time and any other HAV task that day. For WBV, check route, ground, tyres, seat and suspension, load and expected jolts. Confirm training, symptom-reporting route, health-surveillance arrangements where required and a supervisor who can change the plan. A tag or dashboard is a prompt to ask questions, not permission to start. See HSE.
Check the real breaking method, tool condition, consumable and material and compare achievable lower-exposure alternatives rather than purchasing from one emission number. Review representative trigger-time evidence for each worker’s complete tool day, including changes, overtime and uncertainty in the exposure estimate.
Apply the learning
A breaker has a blunt bit and loose component, but extra gloves are proposed as the response to tingling fingers.
Decision and explanation
Stop the defective setup, report symptoms promptly and improve the method, maintenance and exposure controls.
Tool condition can increase vibration and extend the task. Exposure control starts with avoiding or reducing the work and selecting suitable maintained equipment. Gloves may help warmth and other hand protection needs but must not be treated as a dependable vibration control. Health symptoms require the organisation's prompt reporting and occupational-health arrangements, not a diagnosis by the supervisor.
Lesson 15
Hire, modify and return equipment
Stop use and obtain a competent assessment of the proposed modification, safeguards and responsibilities.
Read the workface decision
A modification can change intended use, control functions, stability and supply-law responsibilities. Do not assume the original documentation covers the changed machine. Coordinate with the owner, manufacturer and appropriate competent people. The workface needs clear status and restrictions while the change is considered, rather than a modified item quietly returning to the shared equipment pool.
Visual practice · Hire, modify and return equipment
SHAREhub photographic illustration · Stopped pillar drill with guard in a UK engineering workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
A modification can change intended use, control functions, stability and supply-law responsibilities. Do not assume the original documentation covers the changed machine. Coordinate with the owner, manufacturer and appropriate competent people. The workface needs clear status and restrictions while the change is considered, rather than a modified item quietly returning to the shared equipment pool.
How should modification and change be controlled?
Keep modified, refurbished, relocated, integrated or reprogrammed equipment out of normal work until the change and affected scope are understood, workplace and product-supply duties are resolved, safeguards and controls are restored, applicable inspection and controlled tests pass, and the named operating owner records release. A commissioning or diagnostic test under a controlled plan is not permission for production use. A change to software, controls, guards, attachments, material, location or duty can alter stability, access, stopping, energy, exposure or maintenance.
Evidence to establish at the workface
Provide material-specific source dust control with suitable extraction or suppression, collection and maintenance; keep nearby trades out of unnecessary exposure.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should modification and change be controlled?
Keep modified, refurbished, relocated, integrated or reprogrammed equipment out of normal work until the change and affected scope are understood, workplace and product-supply duties are resolved, safeguards and controls are restored, applicable inspection and controlled tests pass, and the named operating owner records release. A commissioning or diagnostic test under a controlled plan is not permission for production use.
A change to software, controls, guards, attachments, material, location or duty can alter stability, access, stopping, energy, exposure or maintenance. Quarantine unresolved changes and route every correction back through the affected engineering, inspection, test and operational-release gate.
New attachment or duty. Workplace-use question: Is equipment still suitable and guarded?; Product-supply question: Does intended use or conformity scope change?
Control or software change. Workplace-use question: Are modes, stops and restart safe?; Product-supply question: Who now takes manufacturer responsibility?
Refurbishment. Workplace-use question: Is condition and performance demonstrated?; Product-supply question: Is it substantially changed or newly supplied?
Integration. Workplace-use question: Are whole-system risks controlled?; Product-supply question: Does an assembly become a new product?
Provide material-specific source dust control with suitable extraction or suppression, collection and maintenance; keep nearby trades out of unnecessary exposure.
Apply the learning
A hired machine is altered locally to accept a larger workpiece and the original guard no longer fits.
Decision and explanation
Stop use and obtain a competent assessment of the proposed modification, safeguards and responsibilities.
A modification can change intended use, control functions, stability and supply-law responsibilities. Do not assume the original documentation covers the changed machine. Coordinate with the owner, manufacturer and appropriate competent people. The workface needs clear status and restrictions while the change is considered, rather than a modified item quietly returning to the shared equipment pool.
Lesson 16
Check repair and return-to-use evidence
Keep use on hold until the relevant safeguards and safe operating condition are competently verified and released.
Read the workface decision
Verification should address the fault, the repair and other safety functions affected by the work. A production run alone may leave a protective defect untested. The responsible people need an agreed safe test method and a clear return-to-use record. Never expose someone to prove that a guard, stop or interlock works.
Visual practice · Check repair and return-to-use evidence
Actual SHAREsimulate model capture · A mixer jam is reached through an open guard. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Verification should address the fault, the repair and other safety functions affected by the work. A production run alone may leave a protective defect untested. The responsible people need an agreed safe test method and a clear return-to-use record. Never expose someone to prove that a guard, stop or interlock works.
How should a safety function be tested?
Specify the function, safe test position, expected response, acceptance criteria and restoration before a competent person tests it. For an interlock, confirm the guard state, stopped or prevented motion, run-down and restart behaviour for the real access route. A green indicator alone is not proof.
Evidence to establish at the workface
Prevent access to the jam and take the mixer out of use through the authorised process, keeping others from initiating movement.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should a safety function be tested?
Specify the function, safe test position, expected response, acceptance criteria and restoration before a competent person tests it.
For an interlock, confirm the guard state, stopped or prevented motion, run-down and restart behaviour for the real access route. A green indicator alone is not proof. Test from a protected position and record failures; do not put a person in danger to demonstrate the function. After repair or modification, consider the whole linked system, not only the replaced component. HSE L22 Safe use of work equipment and HSE maintenance of work equipment.
Evidence to establish at the workface
Prevent access to the jam and take the mixer out of use through the authorised process, keeping others from initiating movement.
Apply the learning
The repair note says motor runs, but no evidence addresses the interlock that originally failed.
Decision and explanation
Keep use on hold until the relevant safeguards and safe operating condition are competently verified and released.
Verification should address the fault, the repair and other safety functions affected by the work. A production run alone may leave a protective defect untested. The responsible people need an agreed safe test method and a clear return-to-use record. Never expose someone to prove that a guard, stop or interlock works.
Lesson 17
Capstone: a rushed restart
Coordinate competent verification, suitable material, operator information and authorised release before restart.
Read the workface decision
A safe machine is only one part of the decision. Changed people and material may require different instruction, supervision or setup. Connect the technical repair to the real task and define who can confirm readiness. The best handover states the remaining limits, relevant checks and stop triggers in language the receiving team understands.
Visual practice · Capstone: a rushed restart
SHAREhub photographic illustration · Stopped pillar drill with guard in a UK engineering workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
A safe machine is only one part of the decision. Changed people and material may require different instruction, supervision or setup. Connect the technical repair to the real task and define who can confirm readiness. The best handover states the remaining limits, relevant checks and stop triggers in language the receiving team understands.
What must each role learn and demonstrate?
Competence must match the decision and consequence of error. Attendance alone does not show that a worker, manager or specialist can recognise a stop condition, select a control and verify it in practice. Use observed tasks and scenario questions.
Evidence to establish at the workface
Use the equipment-specific clearing method with competent authorisation, effective isolation, secured reconnection control and identified stored-energy measures.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What must each role learn and demonstrate?
Competence must match the decision and consequence of error. Attendance alone does not show that a worker, manager or specialist can recognise a stop condition, select a control and verify it in practice.
Use observed tasks and scenario questions. Reassess after change, defect, incident or a materially different role, and seek a specialist for technical or legal decisions outside local competence.
What must each role learn and demonstrate? decision table
Role
Demonstrated decision
Reassessment trigger
Worker or operator
Explain the task risk, pre-use check and when to stop.
New task, equipment or unsafe event.
Supervisor or manager
Select and verify controls, allocate resources and act on reports.
Work pattern, staffing, process or equipment change.
Maintainer or specialist
Show the technical basis, safe state, examination or referral within own competence.
Modified system, failed test or new evidence.
Safety adviser or auditor
Trace law, hazard, control and field evidence without substituting a checklist for judgement.
Use the equipment-specific clearing method with competent authorisation, effective isolation, secured reconnection control and identified stored-energy measures.
Apply the learning
A repaired mixer, a new operator and a changed material arrive together for the next shift.
Decision and explanation
Coordinate competent verification, suitable material, operator information and authorised release before restart.
A safe machine is only one part of the decision. Changed people and material may require different instruction, supervision or setup. Connect the technical repair to the real task and define who can confirm readiness. The best handover states the remaining limits, relevant checks and stop triggers in language the receiving team understands.
Lesson 18
Make equipment assurance useful
Create a clear quarantine and release process with an owner and evidence that defective equipment cannot be reissued.
Read the workface decision
Assurance is stronger when it tests a believable failure pathway. Follow one defective tool from discovery to removal, repair, verification and controlled reissue. Check hired and subcontractor equipment as well as owned items. A useful improvement changes the physical or organisational barrier and then verifies its effect; training alone cannot repair a missing guard or unreliable isolation system.
Visual practice · Make equipment assurance useful
Actual SHAREsimulate model capture · A damaged breaker is used for excessive trigger time. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Assurance is stronger when it tests a believable failure pathway. Follow one defective tool from discovery to removal, repair, verification and controlled reissue. Check hired and subcontractor equipment as well as owned items. A useful improvement changes the physical or organisational barrier and then verifies its effect; training alone cannot repair a missing guard or unreliable isolation system.
How should work-equipment control be assured?
Assurance should test whether equipment is suitable, safeguards work, defects are controlled, inspections and maintenance match risk, competence is real, contractor interfaces work and return-to-service decisions are evidence based. Use field observation and equipment sampling, not record presence alone. Trend repeated guard damage, bypasses, emergency stops, overdue actions, recurring faults and differences between shifts or sites.
Evidence to establish at the workface
Maintain effective tools and consumables, assess representative vibration and actual trigger times across all tools, and reduce exposure as far as reasonably practicable.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should work-equipment control be assured?
Assurance should test whether equipment is suitable, safeguards work, defects are controlled, inspections and maintenance match risk, competence is real, contractor interfaces work and return-to-service decisions are evidence based.
Use field observation and equipment sampling, not record presence alone. Trend repeated guard damage, bypasses, emergency stops, overdue actions, recurring faults and differences between shifts or sites.
Is the inventory complete? Evidence: Assets, location, owner and status.; Escalation: Unknown equipment held.
Do safeguards work in practice? Evidence: Observed use and functional evidence.; Escalation: Bypass or drift quarantined.
Are defects closed? Evidence: Traceable report, repair and release.; Escalation: Repeat or overdue issue reviewed.
Are people competent? Evidence: Demonstration and supervision.; Escalation: Restriction or refresher based on need.
Which warning signs require immediate attention?
Missing or defeated guards, unexpected movement, unreliable controls, recurring trips, damaged cables or hoses, leaks, unstable equipment, unknown modifications, expired required evidence or informal repairs require a stop, hold or competent review.
Also treat emergency-stop use, reports that workers must reach into danger, and workarounds that have become normal as control failures rather than operator inconvenience.
Guard opened or removed for production. Likely weakness: Safeguarding and workflow conflict.; Action: Stop and redesign or restore.
Frequent reset or emergency stop. Likely weakness: Unresolved fault or process instability.; Action: Quarantine and investigate.
Temporary tape, wedge or bridge. Likely weakness: Device defeated.; Action: Prevent use and escalate.
Inspection or modification unclear. Likely weakness: Evidence gap.; Action: Hold pending competent decision.
Maintain effective tools and consumables, assess representative vibration and actual trigger times across all tools, and reduce exposure as far as reasonably practicable.
Apply the learning
An improvement action asks for more reminders but the defective-tool rack is indistinguishable from the ready-to-use rack.
Decision and explanation
Create a clear quarantine and release process with an owner and evidence that defective equipment cannot be reissued.
Assurance is stronger when it tests a believable failure pathway. Follow one defective tool from discovery to removal, repair, verification and controlled reissue. Check hired and subcontractor equipment as well as owned items. A useful improvement changes the physical or organisational barrier and then verifies its effect; training alone cannot repair a missing guard or unreliable isolation system.