Bales, transport loads and safe clamp access

Free online training · Approximate learning time: 90–150 minutes · Self-paced

Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.

Lesson 1

A stack’s history matters as well as its appearance

Recognise collapse concerns without testing an unstable stack.

Worker moving a carton with a trolley in a UK workplace. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Find: Heavy boxes are picked from the floor and twisted into a cage. Change: Raise the pick position, reorient the cage and repair the threshold. Verify: Maintain cage wheels and observe handling during a realistic peak.

A stack’s history matters as well as its appearance

Bales can roll, slide or fall when a stack loses stability. A leaning outer bale may indicate an immediate concern, but an apparently straight stack is not automatically safe. Bale type, condition, arrangement, support and changes during removal all matter. A person approaching the base to inspect closely may enter the area where a falling bale could strike or trap them.

In the fictional store, a lower bale has been damaged and the outer face has changed shape. Keep people out of the potential collapse area and obtain the responsible competent assessment. Do not push, climb or pull at the stack to see whether it moves. The model's drawing cannot establish a safe stack height, ground capacity or engineering stability. Those depend on the actual bales, storage method and conditions.

Plan storage before arrival, including suitable ground, layout, access, exclusion and the method of placing and removing bales. Keep children and other unauthorised people away. Compare planned mechanical handling from a protected position with workers manually steadying a load. A helper's hands cannot provide reliable stability, and standing beneath raised handling equipment creates another exposure. Equipment must suit the actual load and task and be operated by competent authorised people.

The release decision should verify the corrected stack and a removal sequence that does not undermine it again. Review damage, weather and handling changes over time rather than relying on the original storage record. For the exercise, distinguish observed leaning from unconfirmed structural causes and state the protective boundary and responsible role. No learner should enter a real stack's fall zone to obtain photographs or measurements. A tidy storage label is useful only when the physical arrangement remains stable and access can be maintained without exposing people.

Where do manual handling controls fail?

They fail when organisations focus on worker technique while leaving poor work design, poor equipment and unrealistic workload unchanged.

Warning signs include repeated strains, workers swapping tasks informally, trolleys abandoned because they are hard to use, high absence after peak work, heavy goods stored low or high, damaged wheels, congested routes and supervisors treating pain reports as attitude problems. Sources: HSE L23 Manual handling guidance on regulations; HSE MSD toolkit frequently asked questions

The strongest manual-handling programmes use early reports as design signals. They ask what part of the task is creating unnecessary load and what must change in the process. Sources: HSE L23 Manual handling guidance on regulations; HSE MSD toolkit frequently asked questions

Failure or weak practice How it develops What good looks like
Technique-only control Training repeated but injuries continue. Redesign task and handling aids.Sources: HSE L23 Manual handling guidance on regulations; HSE MSD toolkit frequently asked questions
Mechanical aid not usable Aid exists but route, space or maintenance prevents use. Design route and maintain aid.Sources: HSE L23 Manual handling guidance on regulations; HSE MSD toolkit frequently asked questions
Poor storage Heavy loads stored at floor or overhead level. Slot heavy items at safer heights.Sources: HSE L23 Manual handling guidance on regulations; HSE MSD toolkit frequently asked questions
Unrealistic pace Workers rush and skip aids. Review staffing, schedules and targets.Sources: HSE L23 Manual handling guidance on regulations; HSE MSD toolkit frequently asked questions
No early reporting Discomfort hidden until absence. Supportive reporting and supervisor action.Sources: HSE L23 Manual handling guidance on regulations; HSE MSD toolkit frequently asked questions
Assessment not reviewed Change in load, route or workers ignored. Review after change and incidents.Sources: HSE L23 Manual handling guidance on regulations; HSE MSD toolkit frequently asked questions

Applied case

An outer bale leans after a lower bale is damaged.

Decision and explanation

Exclude people from the potential collapse area and obtain competent assessment and correction.

Do not expose a person to test an unstable load.

Lesson 2

A loading plan starts before the first bale

Match vehicle, load, ground and protected positions.

Separated pedestrian walkway and parked forklift in a UK yard. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Receive and unload identified palletised packaged goods from a rigid lorry using a suitable counterbalance forklift. Act: The supervisor checks the bay surface, lighting, pedestrian barriers, clear route and local unloading plan. Hold / review: Hold an unbooked vehicle, changed vehicle type, unknown load mass, damaged pallet or shifted load for the supervisor and, when needed, supplier or competent specialist.

A loading plan starts before the first bale

Loading changes a vehicle's stability as each bale is placed. Uneven distribution, unsuitable support or an attachment that cannot securely handle the load can expose people before the trailer moves. A worker who stands beside the load to guide it by hand may be struck or crushed. Consider the loading phase as a task in its own right rather than treating restraint at departure as the only control.

The fictional farm needs a competent plan for the actual bale type, handling equipment, trailer, ground and route. Check suitability and condition of the equipment and vehicle, loading position, communication and exclusion. The operator needs the relevant training and authorisation. This lesson does not provide load charts or a universal stacking pattern; use manufacturer information and competent planning for the specific arrangement.

Compare keeping people outside the handling envelope with asking them to watch the load closely. A suitable planned position allows communication without standing under or beside an unstable raised bale. Stop if the agreed communication is lost, somebody enters the danger area or the ground or equipment condition changes. Nobody should try to catch or steady a falling bale. A high-visibility vest cannot protect a person from the force of a dropping load.

Before loading resumes after a defect, verify the corrected equipment and layout through the responsible process. Check what happens when the trailer is partially loaded and when the final restraints are applied, not only its finished appearance. The fictional exercise asks learners to identify the load, equipment, ground, people and sequence evidence missing from a proposal. Record a suitable hold and escalation route rather than inventing a vehicle capacity. A competent loading plan is practical enough to describe safe waiting positions and stop triggers as clearly as the intended destination of the load.

How do you check vehicle and route compatibility?

Check the whole vehicle–load–route combination. A vehicle fitting through a gate, holding a conformity mark or having an adequate nominal capacity does not prove that it can manoeuvre or handle this load safely.

A new delivery vehicle may pass the entrance but need a larger turning area, sweep its trailer over the footway or exceed the unloading equipment’s reach. Ask the supplier or carrier for actual dimensions, load information and operating instructions before accepting the task. HSE vehicle handling explains why size, manoeuvrability and visibility must be considered together. See HSE HSG136 third edition for the relevant source and scope.

CheckDecision to make
Dimensions and swept pathConfirm vehicle and load height, width, length and turning envelope against the entire route, overhead hazards and protected pedestrian space. (HSE)
Surface and stabilityVerify bearing capacity, drainage, slopes and edges for the loaded vehicle and any stabilisers. An unknown cover, void or ground capacity requires a competent assessment. (HSE)
Load and handling equipmentConfirm load identity, mass, centre of gravity, packaging, capacity at the required reach or height, attachments and unloading sequence against the actual instructions. (HSE)
Visibility and protective systemsCheck mirrors, cameras and other controls assumed by the plan. Their coverage and condition must suit the movement; alarms alone do not establish a clear route. (HSE)
Driver and maintenanceCheck relevant competence, site familiarisation, vehicle checks and defect clearance. A road licence or supplier certificate alone does not settle these questions. (HSE)

Worked decision: a carrier substitutes an articulated lorry for the rigid lorry normally used. Its stated width is similar, so reception initially expects it to fit. The supervisor holds it at an agreed safe waiting point. The carrier’s turning information shows the trailer would cross the protected footway on the existing turn. The delivery is reassigned to a suitable vehicle or another assessed unloading arrangement; the pedestrian barrier is not removed to squeeze it through. Record the vehicle identity, route decision, agreed alternative and driver briefing.

For vehicles in use, HSG136 recommends daily driver checks before use and planned maintenance following manufacturer guidance. Check brakes, steering, tyres, lights, visibility aids, restraints, access steps and task-specific safety systems. A safety defect means taking the affected operation out of use until a competent person establishes and verifies a safe solution. A universal weekly route inspection rule is not justified; set route-check frequency from risk, deterioration, use and changes.

Applied case

A helper is asked to steady a raised bale while a loader places it onto the trailer.

Decision and explanation

Use a suitable planned method that keeps people outside the load’s fall and handling envelope.

Manual steadying exposes the person to load movement; redesign the method.

Lesson 3

Restraint must control the journey and the arrival

Check the secured load before movement and unloading.

Separated pedestrian walkway and parked forklift in a UK yard. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Receive and unload identified palletised packaged goods from a rigid lorry using a suitable counterbalance forklift. Act: The supervisor checks the bay surface, lighting, pedestrian barriers, clear route and local unloading plan. Hold / review: Hold an unbooked vehicle, changed vehicle type, unknown load mass, damaged pallet or shifted load for the supervisor and, when needed, supplier or competent specialist.

Restraint must control the journey and the arrival

A stable-looking load while stationary can move during braking, turning or travel over uneven ground. Restraint needs to suit the actual bales, trailer, attachment points and journey. An unsecured bale may fall onto another road user, worker or family member. Slow travel can reduce some forces but is not a substitute for a suitable secured load.

At the fictional departure point, a driver sees loose restraints and a bale projecting beyond the planned arrangement. Hold departure and obtain the responsible operator's correction and check. Do not prescribe a generic number of straps from a model picture. Their type, condition, arrangement and effectiveness depend on the actual load and plan. Vehicle suitability, braking, distribution and route remain relevant as well as the visible restraints.

Arrival is another transition. The receiving area needs suitable ground, protected people and a planned unloading sequence. A load may have shifted during travel, so releasing a restraint can allow material to move. Do not stand in the potential fall path or remove restraints casually because the journey has ended. Competent people must assess the actual condition and use an appropriate method, keeping others clear.

Verification includes the responsible pre-departure check and safe review before unloading. Changes in route, load or weather need consideration under the actual plan, and any required checks during the journey must be performed safely. For the exercise, explain why a photograph of straps does not demonstrate the whole securing system is adequate. Identify the discrepancy, protective hold and evidence the operator must establish. Training work does not create a real transport approval or replace applicable road-transport requirements. Keep the decision focused on a load that remains controlled through loading, movement, restraint release and unloading.

How do you check vehicle and route compatibility?

Check the whole vehicle–load–route combination. A vehicle fitting through a gate, holding a conformity mark or having an adequate nominal capacity does not prove that it can manoeuvre or handle this load safely.

A new delivery vehicle may pass the entrance but need a larger turning area, sweep its trailer over the footway or exceed the unloading equipment’s reach. Ask the supplier or carrier for actual dimensions, load information and operating instructions before accepting the task. HSE vehicle handling explains why size, manoeuvrability and visibility must be considered together. See HSE HSG136 third edition for the relevant source and scope.

CheckDecision to make
Dimensions and swept pathConfirm vehicle and load height, width, length and turning envelope against the entire route, overhead hazards and protected pedestrian space. (HSE)
Surface and stabilityVerify bearing capacity, drainage, slopes and edges for the loaded vehicle and any stabilisers. An unknown cover, void or ground capacity requires a competent assessment. (HSE)
Load and handling equipmentConfirm load identity, mass, centre of gravity, packaging, capacity at the required reach or height, attachments and unloading sequence against the actual instructions. (HSE)
Visibility and protective systemsCheck mirrors, cameras and other controls assumed by the plan. Their coverage and condition must suit the movement; alarms alone do not establish a clear route. (HSE)
Driver and maintenanceCheck relevant competence, site familiarisation, vehicle checks and defect clearance. A road licence or supplier certificate alone does not settle these questions. (HSE)

Worked decision: a carrier substitutes an articulated lorry for the rigid lorry normally used. Its stated width is similar, so reception initially expects it to fit. The supervisor holds it at an agreed safe waiting point. The carrier’s turning information shows the trailer would cross the protected footway on the existing turn. The delivery is reassigned to a suitable vehicle or another assessed unloading arrangement; the pedestrian barrier is not removed to squeeze it through. Record the vehicle identity, route decision, agreed alternative and driver briefing.

For vehicles in use, HSG136 recommends daily driver checks before use and planned maintenance following manufacturer guidance. Check brakes, steering, tyres, lights, visibility aids, restraints, access steps and task-specific safety systems. A safety defect means taking the affected operation out of use until a competent person establishes and verifies a safe solution. A universal weekly route inspection rule is not justified; set route-check frequency from risk, deterioration, use and changes.

Applied case

A driver proposes travelling slowly with one loose restraint and checking it at the destination.

Decision and explanation

Hold departure until the actual load is suitably secured and checked.

Control the load before movement; observation cannot restrain it.

Lesson 4

Clamp work must not depend on an exposed edge

Avoid falls when handling sheets or checking the clamp.

Guarded mobile platform beside a UK industrial building. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Inspect ageing rooflights without stepping on a suspect roof. Act: Review fragility and whether an internal or MEWP method can reach the task; exclude people below. Hold / review: Hold if roof strength, route or protection is uncertain or wind exceeds the equipment limit.

Clamp work must not depend on an exposed edge

A silage clamp edge can expose somebody to a fall while attention is on a sheet, tyre or tool. A surface may be slippery, uneven or visually hard to distinguish from an edge. Holding a large sheet can add pulling forces and obstruct sight. The task's short duration does not remove the consequences of losing balance.

The fictional farm first asks whether the work can be done from a safe ground-level or otherwise protected position. Where access at height remains necessary, a competent plan should select suitable access and collective protection for the actual task. Do not assume a ladder, sheet or tyre provides a working platform. This lesson does not design edge protection or authorise a worker to operate access equipment.

Plan the full sequence, including taking materials up, positioning them and returning. Sheet handling, wind and coordination can create forces that differ from an inspection with empty hands. Avoid a method that keeps the person protected initially but requires a final unprotected reach. Keep vehicles and other workers out of areas affected by falling objects or moving plant. Atmospheric dangers beneath silage sheeting are addressed by no-entry arrangements; a safe edge does not make crawling beneath a sheet acceptable.

If safe access or protection is missing, hold the task and obtain an appropriate alternative. Verify the installed arrangement and the competent working method before release, not merely the arrival of equipment. In the fictional exercise, identify the exposed position and compare an assessed protected method with leaning from a clamp edge. Record changes in weather or access as reasons to reassess. Do not climb onto a real clamp to copy the diagram's viewpoint. The desired outcome is a workable task that avoids the edge or keeps people protected throughout every movement.

How does the work lead to harm?

A person may step through a rooflight, fall from an unprotected edge or opening, slip from unsuitable access equipment, or be struck by an object dropped from above. Distance, landing surface and obstruction affect injury, but a short fall can still be severe. Deterioration, weather and changed routes can defeat yesterday’s plan; identify the fall path and everyone below before selecting equipment.

Identify the source, route to the person, early signal, strongest practicable control and stop decision. Test that decision in real work and after change.

How does the work lead to harm? decision table
ExposureHarm routeControl and hold point
Fragile rooflight or sheetThe surface gives way and a person falls through into the space below.Treat as fragile until a competent check proves otherwise; use protected access and exclusion.
Edge, opening or ladderA slip or overreach leads to a fall onto a hard or obstructed landing.Work from ground where possible; otherwise use a suitable guarded platform and stop if edge or access control fails.
Dropped tool or materialA person below is struck even though the worker above remains protected.Prevent falling objects, segregate the drop zone and stop when exclusion cannot be maintained.

Sources: HSE introduction to working at height safely; HSE roof work; HSENI working at height

Applied case

A worker can place most of the sheet from a protected area but must lean over an open edge for the last corner.

Decision and explanation

Resolve the final exposed step before work proceeds.

Protection must cover the whole task, including the final reach.

Lesson 5

A heavy wheel needs restraint through storage and movement

Keep people out of the toppling path.

Worker moving a carton with a trolley in a UK workplace. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Find: Heavy boxes are picked from the floor and twisted into a cage. Change: Raise the pick position, reorient the cage and repair the threshold. Verify: Maintain cage wheels and observe handling during a realistic peak.

A heavy wheel needs restraint through storage and movement

An agricultural wheel can roll or topple even when it appears to rest securely against a wall. Its shape, size and centre of mass make improvised manual handling difficult. Once it begins to fall, a worker trying to catch it can suffer severe crushing. The potential fall path includes people walking past the stored wheel as well as those intending to move it.

At the fictional workshop, the spare wheel stands upright without effective restraint. Keep people clear and obtain a competent handling and storage method. Avoid pushing it to test balance or asking two people to hold it while another finds equipment. More helpers can place more people in the same danger area. This lesson does not teach tyre inflation, wheel assembly or a universal lifting technique.

Suitable mechanical handling equipment and restraint must fit the actual wheel and task and remain effective through pickup, travel, positioning and release. Review the route, surface, gradients, space and equipment condition. A handling aid is not adequate merely because it is labelled for wheels; it must suit this load and be used competently. Stable storage should prevent inadvertent movement and protect normal access without becoming a new trip or vehicle obstruction.

If the agreed equipment or route is unavailable, hold the move and arrange the necessary correction. The responsible person should verify the whole method from safe positions, including when a restraint changes during transfer. Ask workers about repeated awkward handling and near misses so the design can be improved. For the exercise, mark the toppling envelope and identify which stage loses support. Do not put a volunteer beside an unrestrained wheel for a demonstration. A successful past move cannot establish that a heavy wheel will remain balanced the next time somebody brushes against it.

How should manual handling be assessed?

Assessment should observe the real task, identify risk factors and choose controls that reduce force, posture, frequency, distance and uncertainty.

A good assessment watches the task happen. It measures or estimates load weight, height, reach, distance, frequency, route, floor condition, team communication and use of aids. It asks workers what actually makes the job difficult, not just what the procedure says. Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work

For structured assessment, HSE's Manual Handling Assessment Charts (MAC) support lifting, carrying and team handling. The Risk Assessment of Pushing and Pulling (RAPP) tool supports pushing and pulling. The Assessment of Repetitive Tasks (ART) tool supports repetitive upper-limb tasks. These tools help prioritise risk, but they do not replace judgement or the hierarchy of avoiding and reducing the task. Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work

Question Assessment prompt Output
Can the handling be avoided? Can delivery, storage, automation or process flow remove manual movement? Eliminate or reduce handling need.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
What task factors remain? Height, reach, twist, carry distance, frequency and team coordination. Task redesign actions.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
What load factors matter? Weight, size, grip, stability, centre of gravity and sharp/hot/cold surfaces. Packaging, marking or load reduction.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
What environment factors matter? Floor, lighting, route, weather, heat, cold, space and obstacles. Route and workplace improvements.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
Which tool helps? MAC for lifting/carrying/team handling; RAPP for pushing/pulling; ART for repetition. Structured score and control plan.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
How will controls be checked? Observe use, review discomfort and inspect aids. Supervisor checks and evidence.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work

Applied case

An upright spare wheel begins to tilt and a worker reaches to catch it.

Decision and explanation

Effective restraint and suitable handling that keep people out of the toppling path.

People cannot reliably stop a heavy falling wheel.

Use the appropriate manual handling assessment

This additional teaching takes about 2–5 minutes, in addition to the course estimate. Optional reading and workplace assessment take additional time.

Start by asking whether the hazardous handling can be removed or redesigned. Where handling remains, observe the whole operation with the people who do it and choose an assessment that fits the work.

These aids support the activity assessment. Repetitive upper-limb work may need ART; variable or complex tasks may need other HSE tools or a fuller competent assessment. Mechanical lifting, stored energy, equipment safety and health decisions retain their separate controls. A low factor score, a downloaded report or completion of this course does not approve the work.

TILEO: Task, Individual, Load, Environment and Other factors. MAC: Manual Handling Assessment Charts for appropriate lifting, carrying and team handling. RAPP: Risk Assessment of Pushing and Pulling for appropriate manual pushing and pulling.

Read the portable guide to understand selection, limitations, the mixed-task example and company-branded Word/PDF records. Your existing course checks and completion requirements remain separate.

Read the manual handling tools and records guide

Lesson 6

Storage changes need a fresh readiness decision

Join stability, access and work coordination in the handover.

Maintaining temporary roof-edge protection — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Storage changes need a fresh readiness decision

Storage is dynamic: bales are removed, trailers arrive, wheels move and temporary equipment narrows routes. A layout approved at the start of a season may no longer provide stable loads or safe access. The fictional supervisor should review the current arrangement rather than treating an old stack photograph as continuing evidence. A single changed bale can alter the removal sequence and the area people must avoid.

Prepare a handover showing what is stored, what is being moved, which routes are available and what remains restricted. Include people who do not handle the loads, such as cleaners, visiting drivers and family members. Their access must not rely on understanding an operator's unspoken plan. Establish responsibility for checking equipment and ground, applying restraints and verifying that an area is clear before movement.

Compare a completed record with its physical claim. A loading checklist does not prove a loose strap is effective; a storage diagram does not prove a damaged base bale still supports the stack; a wheel-handling aid does not prove its route is suitable. Use factual observations and competent information to identify the gap. Avoid assigning an attractive risk score to compensate for a missing critical restraint or edge protection.

Before release, verify the corrections and brief the actual sequence and stop conditions. Keep unresolved items as explicit holds with a responsible role and close-out requirement. Observe representative work safely and review reports of leaning loads, route shortcuts or difficult restraint release. For workplace transfer, use the fictional risk and audit prompts to produce one finding, one stronger control and the evidence needed before close-out. Do not create a real inspection certificate or sign as a competent lifting planner. The course supports asking the right questions; actual equipment selection and authorisation remain within the site's competent system.

What warning signs show risk assessment is weak?

Weak assessment usually shows up as generic wording, missed scenarios, poor control evidence and unchanged assessments after change or incidents.

Warning signHow it can cause harmWhat to do
Generic hazard listsPeople do not know the real scenario or required controls.Rewrite around task-specific harm routes.
No worker inputShortcuts, access problems and degraded controls are missed.Walk the task and consult those doing it.
No review after changeNew equipment, substances or contractors create unassessed risk.Trigger review through MOC, procurement and project controls.
Controls not verifiedFailed guards, LEV, alarms or permits are credited as if working.Inspect, test and record control health.
Action tracker ignoredKnown gaps remain open until an incident occurs.Assign owners, dates and senior review.
No stop-work triggersWorkers continue when assumptions are no longer true.Add clear conditions for stopping and escalating.

Applied case

A storage record is signed but a removed bale now leaves a leaning face beside the pedestrian route.

Decision and explanation

The current stability and route evidence, with exclusion until corrected.

Changes require review; historical records cannot hold the load stable.

Lesson 7

Keep people outside an unstable bale stack

Do not collect the product by entering the failure zone.

Two oblique agricultural drawings. Left, a layered stack of textured rectangular bales has a leaning outer bale and a controlled exclusion barrier. Right, a twin-axle bale trailer carries a distributed load with highlighted webbing restraints, headboard, wheels and chassis. Leaders connect stack condition, vehicle suitability and restraint checks.
Original SHAREhub bale-stack and load teaching schematic. Two linked decisions: protect the stack area, then verify the loaded vehicle. Select the drawing to inspect the detail. The written case supplies the decision evidence.

Understand the activity and how harm develops

The outer bale layer leans above the collection route. Weather, settlement or earlier removal can change the load paths within a stack. The next bale movement may release a large section. Standing close to judge whether it will fall places the observer in the very area that needs protecting.

The exercise separates immediate exclusion from later correction. A competent operator needs suitable equipment and a de-stacking plan for the actual bale type and condition. Universal stack dimensions cannot be read from this illustration. The storage layout must also allow correction without pushing people into traffic, overhead-line or building-structure hazards.

Recognise the evidence boundary

QuestionCase evidence
What is observed?The outer bale layer leans above the feed collection route.
How can harm occur?Falling bales could crush someone passing or collecting feed.
What information is needed?Check stack condition, ground support and the de-stacking plan.

Protect, manage and verify

PurposePractical application
Immediate protectionExclude the area and arrange safe mechanical correction by competent operators.
Accountable work arrangementExclude people and vehicle routes from the potential collapse area. Obtain a competent stack assessment and planned mechanical correction. Build and maintain stacks on suitable ground with an arrangement suited to the bales and handling equipment. Keep stack inspections and de-stacking decisions with competent workers; prevent climbing and unauthorised access.
Release verificationConfirm stack stability and the exclusion boundary before access resumes.

Apply this at work

Review the stack again after partial unloading, rain damage or a change in the pedestrian route.

How can maintenance itself be made safe?

Plan intervention hazards before removing guards or opening plant. Control energy, movement, height, substances, contractors and nearby operations for the whole job.

Identify every energy source, bring equipment to the required state, securely isolate, prevent reconnection and release or restrain stored energy. A stop command or open guard is not secure isolation. Use planned exceptional powered fault-finding only with competent specialists and designed protection. Coordinate group work and shift changes. HSE maintenance of work equipment and HSE L22 Safe use of work equipment.

At handback, account for people and tools, restore guards and devices, verify the affected functions and authorise a controlled restart. A permit is a coordination tool where the risk system requires it; it does not substitute for physical controls. Contractors need equipment identity, instructions, hazard information and a defined interface.

Applied case

A feed bale is needed urgently from the leaning side of the stack.

Decision and explanation

Keep the area excluded and arrange competent correction or an alternative supply.

Feed demand does not make the stack stable. An alternative prevents production pressure driving someone into the collapse zone. Removing support can destabilise the stack further and is not an assessed correction method. Observation cannot prevent collapse and climbing adds a fall hazard to the unstable stack.

Lesson 8

Secure the bale load before any movement

Departure is a release decision that requires a secured load.

Workers reviewing a permit beside safely isolated industrial equipment. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Find: Pedestrians and vehicles would share the proposed unloading area. Hold: Keep the load secured while host and driver agree a protected arrangement. Release: Use the planned unloading method and restore access after hand-back.

Understand the activity and how harm develops

Bales project above a trailer waiting at the farm gate. Braking, turning and uneven ground will impose different forces from those present while parked. A bale that seems settled can move when the load is disturbed. The risk extends beyond the farm boundary to other road users.

Inspect loading and restraint as one system: trailer condition, capacity, load distribution, bale type and suitable securing arrangements. Do not let a departure deadline transfer an unresolved load problem onto a public road. The scene also asks where the person checking restraints stands, because climbing an insecure load introduces another avoidable exposure.

Recognise the evidence boundary

QuestionCase evidence
What is observed?Bales shift above the side of a trailer waiting to leave.
How can harm occur?A bale could fall onto road users or farm workers.
What information is needed?Check load security and the trailer loading plan before movement.

Protect, manage and verify

PurposePractical application
Immediate protectionUse a suitable load arrangement and restraints with people kept clear.
Accountable work arrangementUse a suitable trailer and planned load arrangement within its rated capacities. Keep people clear during mechanical loading and securing. Apply suitable load restraints using a method that avoids unnecessary work at height. Have the responsible operator verify load security and vehicle readiness before departure.
Release verificationThe responsible operator checks the secured load before departure.

Apply this at work

Use the same release discipline for seed pallets, machinery transport and deliveries returning from a field.

How does a shifted packaged load change an unloading decision?

Packaged loading and unloading have different hazards from a liquid transfer. Vehicle movement, a falling or unstable load, people in the equipment route and a mismatch between host and driver instructions can cause crushing or impact injury. A liquid-transfer checklist cannot demonstrate control of those routes. Related guidance: Safe loading and unloading.

In an illustrative depot delivery, the driver reports that palletised packs moved in transit and the vehicle is parked beside an active pedestrian route. The receiving supervisor holds unloading and keeps people clear of the potential falling-load area. The host and haulier establish the load condition and a safe unloading method before releasing restraints or opening the affected side. Related guidance: Safe loading and unloading.

Check the loading area, vehicle stability and prevention of unintended movement, safe driver waiting position, pedestrians, suitable handling equipment and the receiving route. The responsible people agree what the driver and site operator each do and how they communicate. Do not improvise a driver climb onto an unstable load or ask someone to catch a shifting package. Related guidance: Safe loading and unloading.

If load stability or equipment suitability is uncertain, obtain competent recovery support and retain the boundary. At completion, verify the remaining load and vehicle state, equipment clear, people clear and the agreed departure release. Record the changed-load event and follow up securing/loading arrangements with the haulier; a completed delivery count says nothing about that control. Related guidance: Safe loading and unloading.

Guidance for these decisions: Safe loading and unloading; Visiting drivers; Loading areas. Apply the legal route for the work location; illustrative scenarios are SHARE teaching examples.

Applied case

The load shifts before departure. The driver proposes driving slowly to the first stop and tightening it there.

Decision and explanation

Before movement, using a suitable reloading or restraint plan.

The observed shift is evidence that the current arrangement needs correction and verification before departure. Waiting for failure exposes workers and road users to a preventable falling-load event. The load would already have travelled through the yard and onto the road without verified security.

Lesson 9

Avoid exposure at the silage clamp edge

Small adjustments still require a planned working position.

Select the work method before equipment
Teaching graphic from the linked SHAREhub source section.

Understand the activity and how harm develops

The worker approaches the top edge to adjust sheeting. The working surface can be uneven and slippery, with wind pulling the sheet or changing the worker balance. A fall can land on concrete or machinery below. The task seems small because the adjustment is small; the possible fall is not.

Start by asking whether the sheet can be managed from a protected position using a suitable system. If access near the edge remains necessary, the work needs planned prevention or protection, safe access and appropriate rescue arrangements. This model has no measured dimensions and cannot specify a safe edge distance or select equipment for a real clamp.

Recognise the evidence boundary

QuestionCase evidence
What is observed?A worker approaches an unprotected clamp edge to adjust sheeting.
How can harm occur?The worker could fall onto concrete or equipment below.
What information is needed?Check whether the work can be done without approaching the edge.

Protect, manage and verify

PurposePractical application
Immediate protectionAvoid edge exposure or provide suitable planned fall protection.
Accountable work arrangementAvoid work near the edge through a suitable ground-based or otherwise protected sheeting method. Plan any necessary access and suitable collective fall prevention before the task. Separate loading and vehicle operations from the sheeting work. Review footing, wind, lighting and the handling demands of the sheet; postpone when controls cannot be maintained.
Release verificationConfirm safe access and edge controls for the actual task.

Apply this at work

Apply the same hierarchy to silo access, bale sheeting and maintenance above machinery.

How do you apply avoid, prevent, minimise?

First avoid work at height where reasonably practicable. If it remains, prevent falls using a safe existing place or suitable equipment. Only then minimise the distance and consequences of a remaining fall.

At each level, consider collective protection before personal protection. A short lanyard configured as restraint prevents reaching an edge; fall arrest permits a fall and needs verified clearance and rescue. Neither makes an unsafe roof sound.

OrderExampleDecision test
AvoidInspect a roof from below or use extendable tools.Can the task be done safely without going up?
Prevent, collectiveGuarded scaffold, tower or suitable MEWP.Can everyone at risk be protected without an individual action?
Prevent, personalVerified work-restraint system.Is the person unable to reach a fall position?
Minimise, collectiveSafety net close below the work.Is competent installation and inspection possible?
Minimise, personalDesigned fall-arrest system.Are anchor, compatibility, clearance and timely rescue verified?

Sources: Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005; HSE introduction to working at height safely; HSE assessing all work at height

Applied case

A loose corner of sheeting can only be reached by leaning over the clamp edge in gusting wind.

Decision and explanation

Pause and arrange a suitable protected method or postpone the work.

The task must fit the available access and weather controls rather than relying on balance at the exposed edge. Holding clothing is not a suitable fall-prevention system and exposes the colleague to being pulled off balance. A tool may reduce reach but leaves the person exposed at the edge in the same unstable conditions.

Lesson 10

Restrain heavy wheels and spares

A clear route and stable storage must be achieved together.

Worker moving a carton with a trolley in a UK workplace. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Find: Heavy boxes are picked from the floor and twisted into a cage. Change: Raise the pick position, reorient the cage and repair the threshold. Verify: Maintain cage wheels and observe handling during a realistic peak.

Understand the activity and how harm develops

A large spare wheel is leaning on the workshop wall. Its weight is concentrated in a tall shape that can roll or topple if nudged. Trying to catch it brings a person into the fall path. The workshop route makes accidental contact more likely as tools and machinery pass.

This is a storage and handling design issue. A suitable rack or restraint prevents instability while a handling aid controls deliberate movement. The chosen aid must suit the wheel and task, including where it is parked during fitting. Tidying by rolling the wheel to another unsupported wall simply relocates the same stored-energy hazard.

Recognise the evidence boundary

QuestionCase evidence
What is observed?A tractor wheel stands upright without restraint beside the workshop door.
How can harm occur?The wheel could topple and crush legs or feet.
What information is needed?Check wheel storage stability and the available handling equipment.

Protect, manage and verify

PurposePractical application
Immediate protectionRestrain storage and use suitable mechanical handling equipment.
Accountable work arrangementExclude the immediate fall area until the wheel can be secured safely. Use a suitable restrained storage position away from pedestrian and vehicle routes. Move and fit heavy wheels using appropriate equipment and competent methods. Keep hands and body clear of pinch points; do not attempt to catch a falling wheel.
Release verificationConfirm the wheel remains stable during storage and transfer.

Apply this at work

Use the same test for detached doors, metal sheets, posts and other heavy farm spares.

What is the difference between TILE, TILEO and TILEE?

TILE, TILEO and TILEE are practical prompts that help assess the whole handling situation rather than focusing only on load weight.

TILE is the core prompt: Task, Individual, Load and Environment. It reflects the main risk factors HSE expects employers to consider when assessing manual handling. TILEO adds Other factors, such as work organisation, time pressure, communication, PPE, fatigue, team handling, handling aids and recovery. TILEE is used by some organisations as a further extension; the final E should be defined in the organisation's standard, most usefully as Equipment, Ergonomics or Existing controls. Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work

The important point is not which acronym is used, but whether the assessment identifies the real risk factors and produces better work design. A TILE/TILEO/TILEE assessment should lead to avoiding the handling where possible, reducing load and reach, improving equipment, changing routes and heights, reducing repetition, supporting individuals and reviewing the work after change. Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work

Prompt What it covers How to use it well
TILE Task, Individual, Load and Environment. Use as the minimum structured check for lifting, carrying, lowering, pushing or pulling.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
Task Posture, reach, twisting, vertical movement, carrying distance, repetition, pace and recovery. Observe the real sequence and remove unnecessary handling before assessing technique.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
Individual Capability, training, fatigue, injury history, pregnancy, disability, temporary restriction and new-starter status. Discuss work impact privately and adjust the task without intrusive medical questioning.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
Load Weight, size, shape, grip, stability, centre of gravity, temperature, sharpness or unpredictability. Reduce, split, mark, package or mechanically move the load where practicable.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
Environment Space, floors, slopes, steps, lighting, weather, temperature, housekeeping, route and access. Fix the route and workplace conditions before asking people to compensate physically.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
TILEO TILE plus Other factors. Add work organisation, time pressure, PPE, communication, team handling, recovery and bystander/interface risks.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
TILEE TILE plus an extra E, usually defined locally as Equipment, Ergonomics or Existing controls. Use to force a check of handling aids, workstation height, layout, mechanical assistance and whether current controls are actually usable.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work
LITE Load, Individual, Task and Environment; the same core ideas in a different order. Acceptable as a shorthand if the assessment still covers the full risk picture.Sources: HSE L23 Manual handling guidance on regulations; HSE manual handling at work

Applied case

The leaning wheel blocks a fire exit. A worker suggests rolling it alone into a quieter corner.

Decision and explanation

Arrange safe mechanical handling into a suitable restrained storage position.

This restores the exit without recreating the toppling hazard elsewhere or exposing a worker to uncontrolled wheel movement. The exit remains obstructed and the wheel can still fall; neither hazard is physically resolved. Emergency access must work for the people who may need it and must not require passing an unstable load.

Lesson 11

The late bale collection

Control loading, travel and storage without improvised support.

Maintaining temporary roof-edge protection — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

The late bale collection

In the fictional case, a late collection arrives as workers finish the shift. The outer bale stack leans after damage to its base, and the usual loader attachment is unavailable. A helper proposes steadying bales by hand during loading. The trailer has a worn restraint and the driver offers to travel slowly. Nearby, a spare wheel leans across the walkway, while a sheet-adjustment task would require a final reach beyond an unprotected clamp edge.

Identify the loads and people in each potential movement path. A falling bale can strike the helper or a person passing the store. The trailer load can shift during travel or when restraints are released. The wheel can topple into the walkway independently of the loading task. The clamp work exposes a person to a fall and possible sheet-handling forces. Treating everything as “manual handling” would hide the separate controls and competent decisions required.

Hold the affected work and establish suitable exclusion and waiting arrangements. Nobody pushes or climbs the leaning stack to prove whether it is stable. Obtain a competent assessment and correction, including the safe removal sequence. Use suitable handling equipment for the actual load and keep people outside its fall and operating envelope. An improvised team lift or manual steadying is not an acceptable substitute for the missing attachment and planned method.

The vehicle and loading plan need to match the actual bale distribution, ground, route and restraint arrangement. Correct the worn restraint through the responsible process and verify the secured load before departure. Do not invent a number of straps or use low travel speed as permission for an unsecured load. Plan the destination and unloading method as well, because release of restraints is a new movement transition. The driver should know what to do if the load condition is uncertain at arrival.

For the spare wheel, keep people outside the toppling path and arrange effective restraint and suitable mechanical handling through its entire movement. Do not ask somebody to hold it while others finish loading. For the clamp, avoid the exposed step or provide an appropriately planned protected method. Holding a worker's belt does not establish fall prevention. Do not go beneath the sheet to make the job easier; that introduces a separate atmosphere hazard.

The final handover states which tasks remain held, who can obtain the necessary competent arrangements and what evidence will release each task. Check that the alternative routes do not create vehicle conflicts. Late collection and shift pressure should lead to rescheduling where necessary rather than ad hoc reduction of controls. Use the fictional audit table to compare each claim with current observations and close-out evidence. A practice score records understanding; it does not certify a stack, approve a transport load or authorise lifting equipment operation.

How do safeguards and barriers fit into risk assessment?

Safeguards and barriers are the controls relied on to prevent, detect, control or mitigate a scenario.

In simple work, a control may be a guard, exclusion zone, ventilation system or instruction. In process safety, the barrier model becomes more explicit: containment prevents release, detection identifies loss of control, shutdown limits escalation, relief protects equipment and emergency response mitigates consequences.

The important question is whether the barrier is real and healthy. A relief valve that is overdue for inspection, a detector in bypass, a permit issued from an office or an alarm with no response standard should not be treated as a reliable safeguard.

Barrier typeExampleEvidence of health
PreventionDesign, substitution, guarding, containment, segregation or isolation.Design standard, inspection, maintenance and change control.
DetectionGas detection, alarms, inspection, monitoring or supervisor check.Calibration, test record, response standard and alarm review.
ControlShutdown, interlock, LEV, permit, safe operating limit or traffic control.Functional test, operator training and deviation records.
MitigationFire protection, spill bund, emergency lighting, first aid or evacuation.Drills, inspections, equipment checks and action closure.
LearningIncident investigation, audit and performance indicators.Trend review, completed actions and management review.

HSE HSG254 connects major-hazard barriers to assurance indicators. HSE HSG254 process safety indicators.

Applied case

The driver asks for one quick load using helpers because the correct attachment will arrive tomorrow.

Decision and explanation

Keep the affected loading held until suitable equipment, stability, exclusion and restraint arrangements are verified.

People must not substitute for load stability or appropriate handling equipment.

Lesson 12

Take a verified action into the workplace

Connect one actual task to an owner, evidence and a clear release or escalation decision.

Maintaining temporary roof-edge protection — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Turn awareness into a practical question

Great Britain farm-work awareness. Confirm the relevant national fire, environmental and pesticide route. Specialist livestock, machinery, electrical, work-at-height, pesticide, confined-space and rescue tasks require their actual competent assessment and authorisation; this course confers none.

Choose one relevant operation from the course. Describe the person or environment at risk, the mechanism of harm and the exact condition that needs controlling. Separate an observation from a conclusion. A display, signature, badge or clean appearance answers only a limited question.

Use the included practice resources to prepare a fictional task brief, risk review or verification question. Decide which competent role owns the decision and which evidence must be available before work restarts or work is released. Keep worker protection, public exclusion, task acceptance and environmental decisions distinct where required.

At work, use your actual approved arrangements. Report uncertainty and preserve the relevant hold, restriction or safe state while it is resolved. Confirm that the action addressed the original harm route and check whether another shift, load, cleaning task or maintenance change could reintroduce it.

Course completion records awareness learning. It does not establish practical competence, certify an organisation or authorise specialist, clinical, maintenance, chemical or emergency work.

How do safeguards and barriers fit into risk assessment?

Safeguards and barriers are the controls relied on to prevent, detect, control or mitigate a scenario.

In simple work, a control may be a guard, exclusion zone, ventilation system or instruction. In process safety, the barrier model becomes more explicit: containment prevents release, detection identifies loss of control, shutdown limits escalation, relief protects equipment and emergency response mitigates consequences.

The important question is whether the barrier is real and healthy. A relief valve that is overdue for inspection, a detector in bypass, a permit issued from an office or an alarm with no response standard should not be treated as a reliable safeguard.

Barrier typeExampleEvidence of health
PreventionDesign, substitution, guarding, containment, segregation or isolation.Design standard, inspection, maintenance and change control.
DetectionGas detection, alarms, inspection, monitoring or supervisor check.Calibration, test record, response standard and alarm review.
ControlShutdown, interlock, LEV, permit, safe operating limit or traffic control.Functional test, operator training and deviation records.
MitigationFire protection, spill bund, emergency lighting, first aid or evacuation.Drills, inspections, equipment checks and action closure.
LearningIncident investigation, audit and performance indicators.Trend review, completed actions and management review.

HSE HSG254 connects major-hazard barriers to assurance indicators. HSE HSG254 process safety indicators.

Applied case

The shift action log says “training completed, issue closed”. It records no condition check, work status or task owner.

Decision and explanation

The accountable person verifies the task-specific control and records the justified decision.

Learning supports the decision; evidence that the relevant control works is needed before the responsible person closes the action.