Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.
Lesson 1
A drinks bottle breaks the identity chain
Chemical hazard pictograms · examples and checksOptional reference · all nine symbols · does not change assessment requirements
READ THE LABEL · UNDERSTAND THE TASK
Recognise the symbol. Read the full label. Assess the actual task.
Examples illustrate possible uses of a symbol, not the classification of every formulation. A product can carry several pictograms. Check its current label, hazard statements and matching safety data sheet (SDS).
Farm chemicals: a pictogram does not replace the product authorisation, label conditions or operator competence.
CLP/GHS hazard pictograms: meanings and illustrative examples
Pictogram and hazard
What it can mean
Example and question before work
ExplosiveGHS01
Explosion, blast or projection hazards; also certain self-reactive substances and organic peroxides.
Example: Certain fireworks or reactive chemical products.Ask: Does the authorised task account for impact, heat and the product’s stability limits?
FlammableGHS02
Can ignite; also used for certain self-heating, pyrophoric or water-reactive hazards.
Example: Petrol or some solvent-based products.Ask: What could release vapour or ignite it during this task, including nearby work?
OxidisingGHS03
Can cause or intensify fire; some strong oxidisers present an explosion hazard.
Example: Oxygen or certain oxidising chemicals.Ask: What incompatible materials and contamination must the assessed storage and connection keep apart?
Gas under pressureGHS04
Pressurised gas may burst if heated; refrigerated gas can cause cold burns.
Example: Compressed-gas cylinders.Ask: Have the gas identity, cylinder, connection and pressure or temperature hazards been checked?
CorrosiveGHS05
May damage metals, cause severe skin burns or cause serious eye damage; read the stated hazard.
Example: Certain drain cleaners, acids or alkalis.Ask: Which contact and splash routes must be prevented in this actual handling or dilution task?
Acute toxicityGHS06
Can be toxic or fatal after short exposure through the stated route.
Example: Methanol or certain pesticide products.Ask: Which exposure routes and emergency arrangements does this product’s information identify?
Harmful / irritantGHS07
May indicate harmful acute toxicity, irritation, skin sensitisation, drowsiness or dizziness; also ozone-layer hazards.
Example: Some detergents or cleaning products.Ask: What do the hazard statements say? Do not dismiss this as a harmless or mild product.
Serious health hazardGHS08
Can indicate cancer, genetic or reproductive harm, organ damage, respiratory sensitisation or aspiration hazard.
Example: Petrol or some sensitising chemical products.Ask: Which particular health effect is stated, and how does the task prevent the relevant exposure?
Hazardous to the environmentGHS09
Hazardous to aquatic life, potentially with long-lasting effects.
Example: Certain pesticides, biocides or fuels.Ask: How will the assessed arrangements prevent release to drains, water or soil?
Read beyond the picture · Open a prompt to compare the explanation.
Is the exclamation mark the same as the chest-starburst symbol?
No. The two symbols communicate different groups of hazards. Read the actual hazard statements: skin sensitisation and respiratory sensitisation are not interchangeable, and neither symbol specifies the complete task controls.
Does a bottle with no pictogram prove the task is safe?
No. Work may generate hazardous dust, fume or mist, and exposure depends on the task. Resolve missing or conflicting identification before use. A pictogram is not a compatibility chart or a complete workplace risk assessment.
Which information turns recognition into a useful work decision?
Match the product and SDS revision. Read the hazard statements and relevant SDS sections for handling, storage, exposure control, emergencies and reactivity together. Then check the actual task assessment and controls. A safety data sheet is not itself a COSHH assessment.
Fisher Scientific UK · BP2618 range · CAS 67-63-0 Revision 19 · 13 October 2023
This learning example refers to the identified supplier edition. It is not a replacement SDS or confirmation that this is the latest sheet for a product you hold. Obtain the current matching supplier SDS before real use.
Below is SHARE’s learning annotation, not a rebranded supplier document or a complete safety data sheet.
Identity
Propan-2-ol / isopropanol; the referenced sheet identifies a laboratory-grade product.
Section 2 signals
Danger; flame and exclamation-mark pictograms. H225, H319 and H336 identify flammability, eye irritation and possible drowsiness/dizziness.
Section 3 composition
The referenced sheet lists isopropyl alcohol above 95% by weight.
Section 8 decision
Engineering measures and several glove-material options appear. Check the complete conditions; no single glove or respirator is selected by this lesson.
Section 9 example
A 12°C closed-cup flash point is listed. This is product data, not a workplace exposure reading or an automatic safe-temperature limit.
Explore every section
1. Identification
Match the product, supplier, intended use and emergency contact to the actual container. A familiar chemical name alone may not identify a formulation.
2. Hazards identification
Read classification, pictograms, signal word and hazard/precautionary statements together. Identify the routes and outcomes the task must prevent.
3. Composition / ingredients
Check concentration and relevant ingredients. A diluted mixture, hardener or changed formulation may need different information and assessment.
4. First-aid measures
Prepare product-specific first-aid arrangements and ready access to the full sheet. Do not replace the workplace emergency procedure with a memory exercise.
5. Firefighting measures
Provide the relevant information to the site fire-planning route. An SDS does not authorise an untrained worker to fight a chemical fire.
6. Accidental release
Plan who raises the alarm, isolates the area and deals with a spill within their training. Confirm available equipment and the boundary for specialist help.
7. Handling and storage
Translate the supplier conditions into the actual transfer, storage, access and housekeeping method. Consider other work and incompatible neighbours.
8. Exposure controls / PPE
Read exposure limits, engineering controls and residual PPE together. Check jurisdiction, units and averaging period. Verify control performance and exact glove/RPE suitability.
9. Physical / chemical properties
Consider volatility, flash point, state and other relevant properties at the actual temperature and method. Odour is not a reliable exposure measurement.
10. Stability / reactivity
Identify incompatible materials, conditions to avoid and possible decomposition. Check the whole process and waste stream, not just separate containers.
11. Toxicological information
Connect the health effects to possible inhalation, skin, eye and ingestion exposure. Use competent advice where specialist interpretation is needed.
12. Ecological information
Plan to prevent environmental release, including drains and water. Lack of a fish/tree symbol does not grant permission to discharge.
13. Disposal considerations
Specify the responsible waste route for the product, contaminated materials and containers. Do not assume evaporation or dilution is an acceptable disposal method.
14. Transport information
Check transport classification through the relevant competent route. Supply pictograms and transport labels have different functions.
15. Regulatory information
Identify relevant restrictions and market scope, then check workplace duties separately. A regulatory entry is not a completed COSHH assessment.
16. Other information
Check revision history, abbreviations and supporting statements. Trace material changes into the assessment, instructions, storage and briefing.
Worked COSHH application · fictional laboratory proposal
Define the proposed use
Fictional laboratory task: wipe small parts for 10 minutes twice per shift, using a proposed 50mL working quantity at ambient temperature. Record the exact product, method, location, people and frequency. These are exercise assumptions, not authorised operating limits.
Find the exposure and application differences
Compare a controlled dispensing/wiping proposal with spraying the same liquid over an open surface near other work. Spray, surface area, ventilation, duration, splashes and nearby people change the assessment even though the SDS is unchanged. Confirm the proposed use is suitable.
Work through the control hierarchy
First ask whether the task can avoid the chemical or use a verified safer method. If it remains necessary, assess release prevention, suitable dispensing, enclosure or ventilation before residual PPE. Do not invent a dilution or declare a small quantity safe.
Specify and verify the real controls
Use sections 7–10 together with competent task assessment. Identify ventilation performance, compatible equipment and the exact glove selection/breakthrough evidence for the job. Consider fire and explosion controls alongside health exposure. Do not copy a generic PPE line and call the work controlled.
Plan the whole job
Include setup, transfer, use, cleaning, storage, waste, maintenance and foreseeable upset. Identify who is exposed, who owns each action, training, first aid, spill arrangements and the separate emergency response boundary.
Record, brief and review
Record significant findings, remaining actions and evidence needed before release. Check controls in use. Reassess for changed product, concentration, quantity, temperature, spraying, location, equipment, symptoms, incidents or new supplier information.
Worked decision: HOLD the proposed task until the matching product/use information, exposure and ignition assessment, control verification and emergency arrangements are resolved by the responsible competent people. This learning example does not issue an operational assessment or authorise work.
Keep an unknown container out of use without sensory testing.
Photorealistic illustrative UK workplace scene. Review checks: Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Storage segregation: Acids, alkalis, oxidisers, flammables and wastes separated.
A drinks bottle breaks the identity chain
A liquid in a drinks bottle can be swallowed by mistake or used as the wrong chemical. Colour, smell and a colleague's recollection cannot establish its identity, concentration or intended use. The absence of a hazard label does not mean the contents are harmless. The fictional store contains just such a bottle beside approved products, so the first problem is uncertainty rather than a chemical name to be guessed.
Keep it out of use and prevent access through the appropriate safe procedure. Do not open, sniff, taste, mix or pour it into a labelled container as an identification test. Handling an unknown product can create splash, inhalation or compatibility hazards. The responsible competent person must establish reliable identity and safe disposition; this course does not teach sampling or unknown-chemical disposal techniques.
Maintain product identity through suitable original or otherwise properly managed containers, labelling, records and controlled storage. Keep chemicals separate from food, drink and personal items. A handwritten nickname is not a substitute for the information needed to assess safe use. Check how the container came to be decanted so the system prevents recurrence rather than only removing this one bottle.
Verification includes the actual container and inventory correction, access control and an understandable reporting route. Staff should know that an instruction from a familiar colleague cannot remove an unresolved identity gap. If someone may have been exposed or swallowed the contents, obtain appropriate urgent assistance under the emergency procedure and provide available information safely; do not improvise treatment or induce actions based on a guessed substance. For the fictional exercise, record the bottle, location and observed circumstances without naming an invented chemical. An uncertainty recorded honestly is safer than a confident but unsupported label.
How should chemical compatibility be assessed?
Compatibility should be assessed by reviewing the chemical inventory, SDS information, reaction hazards, storage locations, transfer routes, drains, waste streams and credible mixing scenarios.
Start with the inventory. List all chemicals, wastes, residues, cleaning chemicals, intermediates, off-spec materials and process fluids. Then identify what could meet what: shelves, bunds, drains, hoses, fill points, waste containers, shared equipment, cleaning routines and emergency response materials.
The SDS is important, especially sections on handling, storage, stability and reactivity, but it does not know your pipework, drain route, container choices or work sequence. A site-specific compatibility review should connect the SDS with the physical workplace.
For higher-risk operations, create credible scenarios: acid into hypochlorite tank, oxidiser into solvent waste, wrong road tanker connection, incompatible drain discharge, cleaning chemical into process residue, rainwater into water-reactive store, or waste drum bulking error.
Compatibility assessment steps
Step
What to assess
Evidence
Inventory
Products, raw materials, intermediates, wastes, residues and cleaners.
Chemical register and waste register.
SDS review
Sections 7, 8, 10, 11 and 13.
SDS review record.
Compatibility matrix
Which substances or classes must be separated.
Matrix or segregation chart.
Physical layout
Stores, bunds, shelves, tanks, drains, transfer points and routes.
Explore an enlarged section of hair-bearing skin, with a hand and forearm for context. Layers, glands, nerves and vessels are enlarged for clarity.
Use the task in this lesson to identify contact, repeated wet work or contamination. Which change reduces contact before relying on gloves?
educational illustration · healthy anatomy; enlarged details and teaching colours.View full detail ↗Lungs and airways in the chest
Locate the lungs, branching airways and diaphragm below them. The cutaway reveals structures normally hidden by the chest wall.
Trace the source-to-breathing-zone route in this lesson. Which change would prevent the contaminant reaching the person?
educational illustration · healthy anatomy; enlarged details and teaching colours.
Related SHAREhub topic guide. Apply its prompts to the specific case below.
Product permission is not task competence
A plant protection product can have specific authorised uses and conditions. The fact that it is sold for agriculture does not authorise every crop, location, mixture or method. A safety data sheet helps explain hazards but does not replace the product's authorisation and label conditions. The fictional task therefore starts with a defined purpose and reliable product information, not with a bottle selected from memory.
The responsible competent user should confirm current authorisation for the intended use, relevant label conditions and the applicable national requirements. Adequate training, instruction and any required certification or registration must be established for the real activity. This awareness course is not pesticide-application certification and does not let a learner instruct others in professional product use. England, Wales, Scotland and Northern Ireland routes must be checked rather than assumed identical.
Plan the whole job: selection, storage, transport, mixing/loading, application, people and environmental interfaces, re-entry, cleaning and disposal. Weather, water, neighbouring activity and worker access can affect the method under the actual product requirements. Do not invent a universal buffer distance, application rate or re-entry time from this course. Nor should an old label photograph be treated as evidence that the current product and authorisation are unchanged.
Hold work when the product, intended use, competence or required arrangements cannot be confirmed. The supervisor should obtain the competent decision and verify that relevant instructions are available and understood. A suitable briefing asks the worker to explain the specific stop condition and reporting route, not simply sign attendance. For the exercise, compare product identity, permission and exposure controls as related but distinct checks. A correct answer demonstrates decision-making only; actual use remains within the qualified authorised system and current product conditions.
What pesticide work flow should be controlled?
A safe pesticide job controls the product from selection through disposal, not just the moment of spraying.
The practical workflow is: justify need -> choose product -> check label/SDS -> assess COSHH -> confirm competence -> plan weather/public interface -> mix/load -> apply -> monitor -> re-entry -> clean equipment -> dispose -> record -> review. Missing one stage can undo the rest.
Stage
Key question
Evidence
Need and selection
Can non-chemical control or a lower-risk product be used?
Pest/weed assessment and product choice record.
Label/SDS review
What are the legal uses, PPE, re-entry and emergency actions?
Label/SDS in work pack.
COSHH assessment
Who could be exposed and by which route?
Task-specific assessment.
Competence
Is the user trained/certificated where required?
Training/certificate record.
Mix/load
Can concentrate be handled without splash, spill or inhalation?
Mixing area and PPE check.
Application
Are weather, drift, public access and equipment controlled?
Application log.
Re-entry
When can workers, public or animals enter treated areas?
Signage/exclusion record.
Cleaning/disposal
How are washings, containers, PPE and waste controlled?
Waste and decontamination record.
Applied case
A product is familiar but its current label and approval for the intended crop are unavailable.
Decision and explanation
Hold use until the competent authorised route confirms the product, intended use and conditions.
Identity, authorised use and safe task arrangements all need confirmation.
Lesson 3
Filling needs a controlled connection and position
Prevent splash at source before choosing PPE.
Photorealistic illustrative UK workplace scene. Review checks: Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Storage segregation: Acids, alkalis, oxidisers, flammables and wastes separated.
Filling needs a controlled connection and position
A loose connection, damaged hose or awkward open pour can put concentrate onto skin, eyes or clothing. Splash can occur before application begins, so the mixing and filling stage needs its own assessment. A worker wearing gloves is not protected against every route, and a product with familiar branding may still require specific precautions. Follow the actual product and task information.
At the fictional filling point, a connection leaks and the operator proposes holding it in place by hand. Stop the affected transfer through the appropriate safe method and obtain competent correction. Do not tighten or disconnect a pressurised or contaminated connection without the authorised arrangement. The safe response must also protect nearby people and avoid creating drainage or environmental exposure.
Stronger controls can include a suitable transfer design that reduces open handling, compatible sound equipment, controlled connections and a practical filling layout. The competent user must assess these for the product and equipment. PPE is selected for the actual substance, task and exposure route and needs correct use, maintenance and removal. A generic glove or face shield cannot compensate for a failed connection or an unsafe pouring position.
Verify repair and the assessed method before resuming. Check the whole sequence, including container handling, disconnection and cleaning, rather than only the instant liquid enters the tank. Appropriate washing, emergency equipment and communication must be available as required by the actual product and assessment. For the exercise, distinguish a physical defect from a training gap: reminding a worker to avoid splashes does not fix the hose. The lesson gives no mixing recipe, dilution rate or universal PPE specification. Competent decisions must follow current product requirements and the actual safe system, with a clear hold where evidence is missing.
How should deliveries and transfers be verified?
Identify the substance, tank and connection independently before opening a transfer path; stop if any identity or barrier is uncertain.
Compare the order, delivery note, container/tank label, SDS and authorised route. A receiving operator should verify the fixed tank and line against a current line map, while the driver checks the vehicle and hose. Dedicated or non-interchangeable couplings, locked and labelled fill points and suitable interlocks protect against a plausible wrong connection. Treat a missing label, unlocked alternative fill line, bypassed interlock or disagreement as a stop condition. The US CSB MGPI case illustrates why a verbal confirmation alone cannot compensate for confusing fill-point design.
On a small screen, scroll this table sideways to read all columns.
Transfer barriers and failure response
Barrier and owner
Check and evidence
Stop/repair
Chemical identity — buyer/receiving lead
Match product, SDS, order and tank inventory; record independent check.
Hold delivery if any identity conflicts.
Connection — engineer/operator
Inspect dedicated fitting, unique label, locked unused lines and line map.
Do not connect if fitting or line is ambiguous.
Transfer — operator and driver
Agree sequence, monitoring, shutoff and emergency signal before flow.
Stop flow and isolate safely after alarm, leak or unexpected change.
Change — process safety lead
Review temporary hose, tank or supplier changes before use.
Do not restart after bypass until authorised correction is verified.
Applied case
A filling hose leaks and the operator wants to grip the joint tighter while transfer continues.
Decision and explanation
Stop the affected transfer safely and obtain competent repair and method verification.
Remove the source defect rather than using a hand as containment.
Lesson 4
Storage compatibility is product-specific
Separate identity, containment and incompatible materials.
Photorealistic illustrative UK workplace scene. Review checks: Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Storage segregation: Acids, alkalis, oxidisers, flammables and wastes separated.
Storage compatibility is product-specific
Two containers on the same shelf are not compatible simply because both are farm chemicals. Contact after a leak can cause harmful reaction, and a common tray can bring incompatible liquids together. Storage also needs to protect people from mistaken selection and unauthorised access. A tidy arrangement can hide a serious compatibility gap if it groups products only by container size or convenience.
Use reliable product identity, label and safety information to support a competent storage assessment. Consider compatible materials, segregation, containment, condition, access and the actual quantities and environment. The fictional cabinet's lettered compartments are teaching labels, not chemical compatibility groups. This course does not provide a universal storage matrix or permission to co-store products that have not been assessed.
Inspect for leaks or damage from a safe position and follow the planned reporting and restriction arrangements. Do not move an unknown leaking container into a shared tray to tidy the shelf or pour residues together. A response to a spill may need trained equipped personnel and environmental controls. Improvised neutralisation or dilution can worsen a reaction; an awareness learner should not attempt it.
The responsible person should verify the corrected inventory, product-specific separation and sound containment, together with arrangements for returns and wastes. Waste liquids and cleaning residues can create mixing routes even when the original products were separated. Include drains, disposal and temporary containers in the review through the appropriate authorised route. For the exercise, identify which facts are known and what evidence is needed before relocating a product. A completed inventory is useful only if it matches the containers and actual storage. Keep uncertain products restricted rather than assigning them to a guessed group based on colour, smell or brand.
How should incompatible chemicals be stored and segregated?
Chemicals should be stored so leaks, breakages, fire water, rainwater, vapours or container failure cannot bring incompatible substances together.
Segregation should be based on real compatibility, not only alphabetic order or convenience. Acids and alkalis should normally be separated; oxidisers should be separated from flammables and combustibles; toxic, cyanide, sulphide, water-reactive and peroxide-forming materials may need specialist controls.
Secondary containment matters. If two incompatible liquids share the same bund, they may mix when containers leak. If chemicals are stacked with incompatible materials above or below each other, a leak can drip into the wrong class.
Storage must be maintained: labels legible, containers closed, shelves compatible, spill kits suitable, expired or unstable chemicals removed, and stock levels controlled.
Segregation controls
Storage issue
Why it matters
Good practice
Acids and alkalis
Can react with heat and splashing.
Separate cabinets, trays or bays.
Oxidisers and flammables
Can intensify fire or cause violent reaction.
Dedicated segregated storage.
Hypochlorite and acids
Can release chlorine gas.
Never store or use together without controlled process design.
Waste chemicals
Composition may be uncertain.
Label, characterise and segregate waste streams.
Shared bunds
Leaks can mix in containment.
Use compatible bunding and separate containment.
Decanted containers
Missing identity creates wrong use and wrong disposal.
Approved labelled containers only.
A hazard-class storage chart is only a starting point. HSE HSG71, paragraph120 warns that substances grouped as compatible can still react; its examples include acid with hypochlorite, cyanide, sulphide or alkali. Check the actual products, residues and leak/drain paths using SDS and competent chemistry advice. This 2009 guidance supports the reaction/segregation principles; its historical legislative references are not the current supply-law route.
Applied case
Two unknown residues are placed in one spill tray because both came from the spray store.
Decision and explanation
Prevent further mixing and obtain the competent product-specific compatibility and response decision.
Shared origin does not establish chemical compatibility.
Lesson 5
Petrol vapour can reach conflicting work
Coordinate handling and ignition prevention before opening a container.
Photorealistic illustrative UK workplace scene. Review checks: Small paint store: Keep minimum stock, use a suitable flammable cabinet, segregate incompatible materials, close containers, remove contaminated waste and inspect the store. Paint spraying booth: LEV/ventilation, Ex equipment, booth maintenance, storage limits, ignition control and cleaning. LPG cylinder cage: Store upright in a ventilated cage, segregate full/empty/damaged cylinders, protect from impact, control smoking/hot work and check valves/hoses.
Petrol vapour can reach conflicting work
Petrol can release flammable vapour during storage and handling. A source of ignition need not be at the container itself if vapour reaches it. In the fictional workshop, fuel handling is planned while grinding occurs nearby. Treat the activity and air path as part of the actual fire and explosion assessment, rather than deciding safety from whether a flame is visible.
Avoid unnecessary handling and use suitable assessed storage, containers, transfer equipment and work arrangements. The responsible competent assessment should address release, ventilation, ignition, spill response and environmental protection for the actual workplace. Non-workplace petrol-storage examples do not automatically define a farm business's legal arrangements. This lesson gives no universal quantity allowance, separation distance or hazardous-zone classification.
Coordinate nearby maintenance and contractor work before transfer. Rescheduling or suitable relocation may remove the conflict more reliably than relying on somebody with an extinguisher. Electrical equipment, hot surfaces, smoking and spark-producing work can all be relevant according to the assessment. Do not assume that moving the can slightly or opening a door establishes adequate ventilation or separation.
If a conflict or leak occurs, use the planned safe stop, warning and emergency arrangements while keeping clear. Do not operate equipment or enter a vapour-affected area to investigate without the appropriate competent method. Firefighting or spill response must stay within the actual trained role and plan; the course does not teach an intervention recipe. Before resuming, verify the corrected physical arrangements and work coordination, not merely that someone has promised to stop grinding. For the exercise, trace a conceptual release-to-ignition path and identify the missing evidence. The diagram is explanatory and cannot establish a real vapour boundary or safe distance.
How should flammable liquids be stored and used?
Flammable liquid control depends on minimising quantities, preventing vapour release, segregating storage, controlling ignition and keeping emergency arrangements realistic.
HSE guidance separates container storage, process/workroom use and bulk tank storage because the risk changes with quantity, containment and release potential. A small workroom stock should normally be limited to what is needed for the work. Larger stocks need purpose-designed cabinets, stores, separation, ventilation, spill containment and emergency planning. Tanks need design, overfill protection, bunding, transfer controls and maintenance.
A common failure is keeping too much flammable liquid at the point of use because it is convenient. DSEAR expects employers to justify quantities and reduce them where reasonably practicable.
Flammable liquid storage and use controls
Setting
Typical controls
Evidence
SettingWorkroom or laboratory use
Typical controlsMinimum quantities, closed containers, ventilation, ignition control, spill kit and local rules.
EvidenceDSEAR assessment, inventory and inspection checks.
EvidenceCabinet inspection, inventory and worker briefing.
SettingDedicated flammable store
Typical controlsFire-resisting construction, ventilation, separation, spill containment and emergency access.
EvidenceStore inspection, segregation checks and maintenance records.
SettingBulk tank storage
Typical controlsOverfill protection, bunding, transfer supervision, vents, earthing, inspection and emergency planning.
EvidenceHSG176-aligned assessment, tank inspection and proof tests.
SettingDispensing and transfer
Typical controlsClosed transfer, bonding/earthing, compatible equipment, supervision and emergency stop.
EvidenceProcedure, training and transfer records.
SettingWaste liquids
Typical controlsClosed, labelled, segregated waste containers and timely removal.
EvidenceWaste register, inspections and disposal records.
HSG140 covers use and handling; HSG51 covers containers, HSG176 bulk tanks and HSG71 packaged chemical warehousing. Check the actual activity and current assessment: HSE HSG140.
Petrol transfer is planned beside ongoing grinder work; a worker offers to hold an extinguisher.
Decision and explanation
Prevent the conflict through the actual assessed handling and ignition-control arrangement.
Control the release/ignition combination before work; response equipment is not a substitute.
Lesson 6
Exposure response and disposal complete the job
Keep urgent assistance separate from equipment investigation.
Related SHAREhub topic guide. Apply its prompts to the specific case below.
Exposure response and disposal complete the job
Chemical work does not end when application or filling stops. Contaminated clothing, equipment, washings and residues can expose the next worker or enter an unsuitable waste route. A person may also have an exposure needing prompt help while others focus on cleaning the area. The fictional supervisor must protect people first and keep the later investigation within competent arrangements.
After suspected exposure, stop the affected activity safely, obtain appropriate first-aid or urgent medical assistance and follow the product-specific emergency information and site plan. Serious illness or injury requires emergency help. Provide reliable product details safely to responders. Do not diagnose poisoning, prescribe treatment, induce vomiting or improvise neutralisation from a course example. Unknown identity is a fact to communicate, not a reason to guess.
Prevent secondary exposure while arranging competent handling of contaminated equipment and materials. The approved cleaning, storage and disposal method must suit the actual product, equipment and national environmental requirements. A drain or ordinary waste container is not automatically an authorised route. Contaminated PPE removal can transfer material to skin, so its method and facilities need to be part of the assessed system rather than an afterthought.
Restart requires the necessary corrections, exposure review, equipment verification and authorised release. Record factual observations, actions and information gaps without publishing private medical details. Investigate whether identity control, equipment, training, staffing or work pressure contributed and choose measures that prevent recurrence. For the exercise, produce a fictional handover with separate columns for person support, area restriction, competent cleanup and evidence before release. A completed incident form does not prove the area is clean or a worker is medically fit. Keep each decision with the role qualified to make it.
What should happen after suspected pesticide poisoning?
Suspected harmful poisoning needs urgent help. Call 999 or attend A&E for suspected harmful exposure or severe signs; seek immediate medical advice if affected, unwell or worried after pesticide exposure. Do not wait for symptoms to persist.
Workplace managers should not diagnose pesticide poisoning. If someone has collapsed, has breathing difficulty, severe eye exposure, confusion, seizures, severe vomiting, significant skin contamination or other serious symptoms after pesticide exposure, emergency arrangements and medical advice should be used immediately. Do not wait to complete internal paperwork before seeking help.
The workplace response should preserve the product name, label, SDS, active ingredient, exposure route, time, task and first-aid actions so clinicians and investigators can understand what happened.
Exposure event
Immediate workplace action
Information to preserve
Inhalation during spraying or fogging
Move away from exposure, stop work, get first aid and immediate medical advice if affected, unwell or worried after exposure.
Product, active ingredient, application method, ventilation and duration.
Skin contamination
Remove contaminated clothing, wash as label/SDS directs and obtain immediate medical advice if affected, unwell or worried after exposure.
PPE worn, contaminated body area and decontamination time.
Eye splash
Use eyewash as instructed and seek medical advice.
Product label/SDS and time of irrigation.
Ingestion or hand-to-mouth transfer
Do not rely on workplace judgement; follow label/SDS/medical advice.
Amount, product, route and timing.
Large spill or drift incident
Isolate area, keep unprotected people away and use competent clean-up.
Weather, location, people affected and spill response.
Applied case
A worker has a chemical splash while others start washing residues towards an ordinary drain.
Decision and explanation
Protect the person and obtain appropriate assistance while controlling secondary exposure and using the authorised cleanup/waste route.
Urgent assistance and competent containment/disposal are separate necessary workstreams.
Lesson 7
Keep chemicals in identified containers
Container identity is a safety control, not merely an inventory convenience.
Teaching graphic from the linked SHAREhub source section.
Understand the activity and how harm develops
The drinks bottle contains an unidentified chemical. Its shape suggests something safe to drink and removes the label information needed for use, storage and emergency treatment. A person who did not fill it cannot safely infer the contents from colour or smell. The uncertainty is itself a reason to stop handling it as a normal product.
The scene connects storage discipline with worker communication. Decanting arrangements, labels and access control must work for seasonal workers and visiting contractors as well as the person who buys the product. An unknown substance should be secured and assessed through a competent process; tasting, sniffing or mixing a sample creates new exposure.
Recognise the evidence boundary
Question
Case evidence
What is observed?
An unlabelled soft-drink bottle contains liquid from the spray store.
How can harm occur?
Someone could swallow the chemical or use it incorrectly.
What information is needed?
Ask for the original product identity and safety information.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Keep chemicals in suitable labelled packaging and secure the unidentified item.
Accountable work arrangement
Never use food or drink containers for chemicals. Use suitable compatible containers with the required product identification and handling information. Secure the unidentified bottle and obtain competent identification and disposal advice. Maintain inventory, safety data and worker instruction for all products used on the farm.
Release verification
Confirm identity, safe disposition and corrected storage practice.
Apply this at work
Include fuel cans, spray bottles, veterinary products and chemicals carried in machinery cabs.
How should a COSHH health-risk assessment be carried out?
A COSHH assessment should identify hazardous substances, assess exposure, decide controls, record findings, implement actions and review effectiveness.
Start by creating a substance and process inventory. Include what is bought, what is generated and what appears during cleaning, maintenance, waste handling and emergencies. Then observe the task. The person doing the work often knows where dust escapes, where splashes occur and where the written procedure is unrealistic.
The assessment should be task-based. A single product may need different assessments for brushing, spraying, decanting, heating, cleaning and waste handling. Similarly, a single dust hazard may need different controls for cutting, drilling, sweeping, bag emptying and filter changing.
The output should be a usable control plan. It should state what controls are required before work, during work and after work; who checks them; what training is required; what records are kept; and what triggers review.
A clear liquid in a soft-drink bottle is found in the chemical store. Nobody can confirm its contents.
Decision and explanation
Secure it and arrange competent identification or disposal without informal testing.
Smelling an unknown chemical creates exposure and does not reliably identify its composition. Mixing unknown substances can cause reaction and destroys reliable product identification. The unknown contents require a controlled response that prevents use, ingestion and incompatible mixing.
Lesson 8
Control splash at the chemical filling task
Know the emergency response before opening the concentrate.
Teaching graphic from the linked SHAREhub source section.
Understand the activity and how harm develops
The worker is transferring concentrate into a sprayer. A splash can reach the face or skin during opening, pouring, connection failure or rinsing. The assessment must use the actual product, task and application method; a generic pair of gloves cannot be assumed suitable. Concentrate handling may differ substantially from using the diluted product.
Look at the filling height, stability, connections and access to washing or emergency facilities. Better transfer equipment can reduce pouring and contact. Product labels and safety information guide task-specific precautions, while competent operators need to understand the method. An emergency facility only helps when people can reach and use it promptly.
Recognise the evidence boundary
Question
Case evidence
What is observed?
A loose hose sprays concentrate towards the operator's face.
How can harm occur?
Contact could burn eyes or skin or cause other toxic effects.
What information is needed?
Check the product instructions and filling equipment condition.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Stop the leak and use suitable transfer equipment and specified protection.
Accountable work arrangement
Use a lower-exposure transfer method and suitable stable filling arrangement where practicable. Follow the product label, assessment and competent operating procedure for mixing and filling. Select suitable chemical protection for the actual product and task, including eyes and face where required. Provide accessible washing and emergency arrangements and prevent spills reaching people or drains.
Release verification
Confirm sound connections and an effective assessed filling method.
Apply this at work
Apply the transfer review to disinfectants, fuels, veterinary medicines and workshop cleaning agents.
How should a COSHH health-risk assessment be carried out?
A COSHH assessment should identify hazardous substances, assess exposure, decide controls, record findings, implement actions and review effectiveness.
Start by creating a substance and process inventory. Include what is bought, what is generated and what appears during cleaning, maintenance, waste handling and emergencies. Then observe the task. The person doing the work often knows where dust escapes, where splashes occur and where the written procedure is unrealistic.
The assessment should be task-based. A single product may need different assessments for brushing, spraying, decanting, heating, cleaning and waste handling. Similarly, a single dust hazard may need different controls for cutting, drilling, sweeping, bag emptying and filter changing.
The output should be a usable control plan. It should state what controls are required before work, during work and after work; who checks them; what training is required; what records are kept; and what triggers review.
The filling connection leaks and concentrate splashes onto the worker face.
Decision and explanation
Stop exposure, follow the product emergency instructions and obtain appropriate urgent help.
A contaminated glove can spread chemical and delay the required emergency washing and treatment. Improvised neutralisation can react or worsen injury. Use the specified emergency procedure rather than mixing substances on the person. The response must use the actual substance instructions and prompt professional advice; product information should accompany the request for help.
Lesson 9
Store for compatibility and spill control
Storage design must consider the path of a leak as well as the location of a container.
Photorealistic illustrative UK workplace scene. Review checks: Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Storage segregation: Acids, alkalis, oxidisers, flammables and wastes separated.
Understand the activity and how harm develops
Different products share a shelf with no reliable segregation or containment. A leaking container can contact another product or reach the yard drain. Product category names alone do not establish compatibility. The actual contents, quantities, storage conditions and label requirements determine the arrangement.
In this exercise, trace where a shelf leak would go and who would discover it. An absorbent mat is not a substitute for a suitable store and planned response. The stock system should support identification, access, inspection and appropriate disposal. Keeping obsolete or unlabelled containers indefinitely increases uncertainty for everyone using or maintaining the store.
Recognise the evidence boundary
Question
Case evidence
What is observed?
Leaking containers share a tray with products of unknown compatibility.
How can harm occur?
A spill could react, release harmful material or pollute water.
What information is needed?
Compare labels and safety data with the store segregation plan.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Contain and segregate using the assessed method and competent assistance.
Accountable work arrangement
Reduce unnecessary stocks and arrange suitable disposal of obsolete products. Separate incompatible substances using product-specific storage information. Provide suitable secure storage and compatible containment with protected drainage. Maintain inventory, inspections, spill-response arrangements and competent access control.
Release verification
Check compatible storage, intact containment and corrected records.
Apply this at work
Use the same containment and compatibility review for waste chemicals, fuel stores and maintenance products.
How should incompatible chemicals be stored and segregated?
Chemicals should be stored so leaks, breakages, fire water, rainwater, vapours or container failure cannot bring incompatible substances together.
Segregation should be based on real compatibility, not only alphabetic order or convenience. Acids and alkalis should normally be separated; oxidisers should be separated from flammables and combustibles; toxic, cyanide, sulphide, water-reactive and peroxide-forming materials may need specialist controls.
Secondary containment matters. If two incompatible liquids share the same bund, they may mix when containers leak. If chemicals are stacked with incompatible materials above or below each other, a leak can drip into the wrong class.
Storage must be maintained: labels legible, containers closed, shelves compatible, spill kits suitable, expired or unstable chemicals removed, and stock levels controlled.
Segregation controls
Storage issue
Why it matters
Good practice
Acids and alkalis
Can react with heat and splashing.
Separate cabinets, trays or bays.
Oxidisers and flammables
Can intensify fire or cause violent reaction.
Dedicated segregated storage.
Hypochlorite and acids
Can release chlorine gas.
Never store or use together without controlled process design.
Waste chemicals
Composition may be uncertain.
Label, characterise and segregate waste streams.
Shared bunds
Leaks can mix in containment.
Use compatible bunding and separate containment.
Decanted containers
Missing identity creates wrong use and wrong disposal.
Approved labelled containers only.
A hazard-class storage chart is only a starting point. HSE HSG71, paragraph120 warns that substances grouped as compatible can still react; its examples include acid with hypochlorite, cyanide, sulphide or alkali. Check the actual products, residues and leak/drain paths using SDS and competent chemistry advice. This 2009 guidance supports the reaction/segregation principles; its historical legislative references are not the current supply-law route.
Applied case
A leaking container sits above another chemical and the spill is approaching the doorway.
Decision and explanation
Keep people clear and activate the product-specific spill response with competent help.
Unplanned handling can expose workers or mix incompatible products. The response must be based on identification and a suitable plan. This can spread the substance into drains and other work areas while leaving compatibility and exposure unresolved. The response needs to control exposure and prevent incompatible contact or environmental release using suitable equipment and information.
Lesson 10
Prevent ignition during petrol transfer
Manage the vapour and nearby work, not only the visible liquid.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Flour silo, connected dust filter and transfer duct at a food-processing site. Act: Reduce dust release and ignition; confirm material test data, filter and silo volumes, vent discharge path, duct connections and protection design basis. Hold / review: Stop transfer if a critical collector fails, a vent is obstructed, isolation is impaired or changed ducting has not been reassessed.
Understand the activity and how harm develops
Petrol is being handled near a possible ignition source. Vapour can travel away from the visible liquid and collect where ventilation is poor. A small transfer can therefore create a hazard beyond the mouth of the container. The task needs suitable containers, location and equipment rather than confidence based on the amount being moved.
Look at storage, dispensing and waste together. Spills, contaminated materials and nearby drains can extend the consequences. The scene asks who controls other work, such as grinding or smoking, while transfer occurs. Fire response depends on early warning, escape and calling help; it should not depend on a worker improvising close to a growing fire.
Recognise the evidence boundary
Question
Case evidence
What is observed?
Petrol is decanted beside a running heater.
How can harm occur?
Vapour could ignite and cause burns or fire.
What information is needed?
Check the fuel-handling assessment and ignition-source controls.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Stop the activity and arrange approved storage and transfer away from ignition.
Accountable work arrangement
Avoid unnecessary petrol handling and use a suitable lower-risk alternative where feasible. Use approved suitable containers, transfer equipment and a properly assessed location. Exclude ignition sources and incompatible nearby work; manage spills and contaminated waste. Maintain emergency communication, clear escape routes and suitable fire arrangements.
Release verification
Confirm the handling area and equipment satisfy the assessed method.
Apply this at work
Include portable generators, vehicle refuelling and waste-fuel handling in the farm dangerous-substances assessment.
How should dust extraction and powder handling systems be protected?
Dust systems should be protected by preventing dust escape, controlling ignition, maintaining extraction and using relief, isolation or suppression where needed.
Dust extraction and powder systems can create both process risk and building risk. A leak, blocked filter, failed housekeeping regime or modified duct can allow dust to accumulate. The primary explosion may start inside equipment, but the worst harm may occur when settled dust becomes airborne in a secondary explosion.
Protection should be chosen from the actual system: collectors, silos, mills, dryers, conveyors, filters, elevators, hoppers and ducts may each need different controls. A competent assessment should identify where ignition could occur and how an event could propagate.
A worker is decanting petrol while grinding starts at the neighbouring workshop door.
Decision and explanation
Stop the conflicting work and restore the assessed transfer and ignition controls.
Rushing does not control vapour travel and can increase the chance of a spill. A rag is not a suitable vapour or ignition barrier and may become contaminated fuel for a fire. The simultaneous activities defeat separation. Coordinate them before any authorised restart of the transfer.
Lesson 11
The borrowed bottle and rushed filling task
Resolve identity, exposure, compatibility and ignition together.
Photorealistic illustrative UK workplace scene. Review checks: Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Storage segregation: Acids, alkalis, oxidisers, flammables and wastes separated.
The borrowed bottle and rushed filling task
The fictional spray team is preparing a task before rain arrives. A clear liquid in a drinks bottle is described as the usual additive, but reliable identity is missing. The current label for the selected pesticide is unavailable. A filling connection leaks, two residues share a tray without a compatibility decision and petrol is being handled beside a contractor's grinder. A worker reports a splash onto their clothing and skin.
Begin with protection and appropriate assistance for the exposure. Stop the affected activity safely, follow the actual product and emergency arrangements and obtain urgent help where needed. Give responders available reliable identity and circumstances without guessing the contents of the bottle. Prevent secondary contact. Do not improvise treatment, neutralisation or an unassessed washdown to a drain. This course supplies awareness decisions rather than clinical or spill-response operating instructions.
The identity and authorisation gaps prevent use. Keep the drinks bottle out of use and restrict access through the suitable safe procedure while the competent person establishes identity and disposition. No smelling, tasting or mixing test is acceptable. Confirm the current product's authorised intended use, label conditions, required competence and national route before resuming. A safety data sheet does not by itself authorise every crop or application, and last season's remembered rate is not a substitute for current instructions.
The filling defect needs competent correction and verification of the actual transfer method. Holding a leaking joint by hand or adding generic PPE leaves the release mechanism active. Review equipment compatibility, sound connections, handling positions, washing and emergency arrangements for every stage, including disconnection and cleaning. Keep the lesson separate from pesticide-application certification; the learner cannot approve a mixture or teach professional use merely by completing this course.
The shared-tray residues require a competent compatibility and response decision. Do not combine them further or relocate unknown products for tidiness. Storage, contaminated PPE, washings and wastes must follow the assessed authorised route. The petrol and grinder conflict also remains held until suitable handling and ignition-prevention arrangements are established. An extinguisher and a promise to watch vapour do not remove the release/ignition pathway.
Before release, identify each correction, responsible role and evidence: reliable product identity, current intended-use conditions, competence, sound transfer equipment, compatible storage, controlled waste and ignition coordination. Verify the real arrangement rather than collecting signatures alone. Weather pressure is a reason to reschedule when necessary, not to reduce the standard. Use a fictional audit and briefing to test understanding of the stop conditions. A practice pass cannot authorise a pesticide operation, certify chemical compatibility or declare a worker medically fit.
How should chemical compatibility be assessed?
Compatibility should be assessed by reviewing the chemical inventory, SDS information, reaction hazards, storage locations, transfer routes, drains, waste streams and credible mixing scenarios.
Start with the inventory. List all chemicals, wastes, residues, cleaning chemicals, intermediates, off-spec materials and process fluids. Then identify what could meet what: shelves, bunds, drains, hoses, fill points, waste containers, shared equipment, cleaning routines and emergency response materials.
The SDS is important, especially sections on handling, storage, stability and reactivity, but it does not know your pipework, drain route, container choices or work sequence. A site-specific compatibility review should connect the SDS with the physical workplace.
For higher-risk operations, create credible scenarios: acid into hypochlorite tank, oxidiser into solvent waste, wrong road tanker connection, incompatible drain discharge, cleaning chemical into process residue, rainwater into water-reactive store, or waste drum bulking error.
Compatibility assessment steps
Step
What to assess
Evidence
Inventory
Products, raw materials, intermediates, wastes, residues and cleaners.
Chemical register and waste register.
SDS review
Sections 7, 8, 10, 11 and 13.
SDS review record.
Compatibility matrix
Which substances or classes must be separated.
Matrix or segregation chart.
Physical layout
Stores, bunds, shelves, tanks, drains, transfer points and routes.
Labels, locks, couplings, interlocks, permits, procedures and supervision.
Barrier register and test records.
Applied case
The team asks to use the remembered recipe so the job can finish before rain.
Decision and explanation
Keep the affected work held until person support and verified identity, authorisation, transfer, storage and ignition controls are established.
Multiple critical gaps remain; weather pressure does not resolve them.
Lesson 12
Take a verified action into the workplace
Connect one actual task to an owner, evidence and a clear release or escalation decision.
Photorealistic illustrative UK workplace scene. Review checks: Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Storage segregation: Acids, alkalis, oxidisers, flammables and wastes separated.
Turn awareness into a practical question
Great Britain farm-work awareness. Confirm the relevant national fire, environmental and pesticide route. Specialist livestock, machinery, electrical, work-at-height, pesticide, confined-space and rescue tasks require their actual competent assessment and authorisation; this course confers none.
Choose one relevant operation from the course. Describe the person or environment at risk, the mechanism of harm and the exact condition that needs controlling. Separate an observation from a conclusion. A display, signature, badge or clean appearance answers only a limited question.
Use the included practice resources to prepare a fictional task brief, risk review or verification question. Decide which competent role owns the decision and which evidence must be available before work restarts or work is released. Keep worker protection, public exclusion, task acceptance and environmental decisions distinct where required.
At work, use your actual approved arrangements. Report uncertainty and preserve the relevant hold, restriction or safe state while it is resolved. Confirm that the action addressed the original harm route and check whether another shift, load, cleaning task or maintenance change could reintroduce it.
Course completion records awareness learning. It does not establish practical competence, certify an organisation or authorise specialist, clinical, maintenance, chemical or emergency work.
How should chemical compatibility be assessed?
Compatibility should be assessed by reviewing the chemical inventory, SDS information, reaction hazards, storage locations, transfer routes, drains, waste streams and credible mixing scenarios.
Start with the inventory. List all chemicals, wastes, residues, cleaning chemicals, intermediates, off-spec materials and process fluids. Then identify what could meet what: shelves, bunds, drains, hoses, fill points, waste containers, shared equipment, cleaning routines and emergency response materials.
The SDS is important, especially sections on handling, storage, stability and reactivity, but it does not know your pipework, drain route, container choices or work sequence. A site-specific compatibility review should connect the SDS with the physical workplace.
For higher-risk operations, create credible scenarios: acid into hypochlorite tank, oxidiser into solvent waste, wrong road tanker connection, incompatible drain discharge, cleaning chemical into process residue, rainwater into water-reactive store, or waste drum bulking error.
Compatibility assessment steps
Step
What to assess
Evidence
Inventory
Products, raw materials, intermediates, wastes, residues and cleaners.
Chemical register and waste register.
SDS review
Sections 7, 8, 10, 11 and 13.
SDS review record.
Compatibility matrix
Which substances or classes must be separated.
Matrix or segregation chart.
Physical layout
Stores, bunds, shelves, tanks, drains, transfer points and routes.
Labels, locks, couplings, interlocks, permits, procedures and supervision.
Barrier register and test records.
Applied case
The shift action log says “training completed, issue closed”. It records no condition check, work status or task owner.
Decision and explanation
The accountable person verifies the task-specific control and records the justified decision.
Learning supports the decision; evidence that the relevant control works is needed before the responsible person closes the action.
Match the nine hazard symbols
End-of-course revision · Drag each symbol to its hazard name, or use the menu on each card with touch or keyboard. This is practice alongside the separate final assessment.
Acute toxicity
Corrosive
Explosive
Flammable
Gas under pressure
Harmful / irritant
Hazardous to the environment
Oxidising
Serious health hazard
Match all nine symbols, then check your choices.
Need the reference table?Chemical hazard pictograms · examples and checksOptional reference · all nine symbols · does not change assessment requirements
READ THE LABEL · UNDERSTAND THE TASK
Recognise the symbol. Read the full label. Assess the actual task.
Examples illustrate possible uses of a symbol, not the classification of every formulation. A product can carry several pictograms. Check its current label, hazard statements and matching safety data sheet (SDS).
CLP/GHS hazard pictograms: meanings and illustrative examples
Pictogram and hazard
What it can mean
Example and question before work
ExplosiveGHS01
Explosion, blast or projection hazards; also certain self-reactive substances and organic peroxides.
Example: Certain fireworks or reactive chemical products.Ask: Does the authorised task account for impact, heat and the product’s stability limits?
FlammableGHS02
Can ignite; also used for certain self-heating, pyrophoric or water-reactive hazards.
Example: Petrol or some solvent-based products.Ask: What could release vapour or ignite it during this task, including nearby work?
OxidisingGHS03
Can cause or intensify fire; some strong oxidisers present an explosion hazard.
Example: Oxygen or certain oxidising chemicals.Ask: What incompatible materials and contamination must the assessed storage and connection keep apart?
Gas under pressureGHS04
Pressurised gas may burst if heated; refrigerated gas can cause cold burns.
Example: Compressed-gas cylinders.Ask: Have the gas identity, cylinder, connection and pressure or temperature hazards been checked?
CorrosiveGHS05
May damage metals, cause severe skin burns or cause serious eye damage; read the stated hazard.
Example: Certain drain cleaners, acids or alkalis.Ask: Which contact and splash routes must be prevented in this actual handling or dilution task?
Acute toxicityGHS06
Can be toxic or fatal after short exposure through the stated route.
Example: Methanol or certain pesticide products.Ask: Which exposure routes and emergency arrangements does this product’s information identify?
Harmful / irritantGHS07
May indicate harmful acute toxicity, irritation, skin sensitisation, drowsiness or dizziness; also ozone-layer hazards.
Example: Some detergents or cleaning products.Ask: What do the hazard statements say? Do not dismiss this as a harmless or mild product.
Serious health hazardGHS08
Can indicate cancer, genetic or reproductive harm, organ damage, respiratory sensitisation or aspiration hazard.
Example: Petrol or some sensitising chemical products.Ask: Which particular health effect is stated, and how does the task prevent the relevant exposure?
Hazardous to the environmentGHS09
Hazardous to aquatic life, potentially with long-lasting effects.
Example: Certain pesticides, biocides or fuels.Ask: How will the assessed arrangements prevent release to drains, water or soil?
Read beyond the picture · Open a prompt to compare the explanation.
Is the exclamation mark the same as the chest-starburst symbol?
No. The two symbols communicate different groups of hazards. Read the actual hazard statements: skin sensitisation and respiratory sensitisation are not interchangeable, and neither symbol specifies the complete task controls.
Does a bottle with no pictogram prove the task is safe?
No. Work may generate hazardous dust, fume or mist, and exposure depends on the task. Resolve missing or conflicting identification before use. A pictogram is not a compatibility chart or a complete workplace risk assessment.
Which information turns recognition into a useful work decision?
Match the product and SDS revision. Read the hazard statements and relevant SDS sections for handling, storage, exposure control, emergencies and reactivity together. Then check the actual task assessment and controls. A safety data sheet is not itself a COSHH assessment.