Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.
Lesson 1
Avoid the overhead-line interface
Plan for the highest and widest equipment configuration.
Teaching graphic from the linked SHAREhub source section.
Avoid the overhead-line interface
Electricity can arc across a gap when machinery approaches an overhead line; direct contact is not necessary for injury. Equipment height changes when a trailer tips, a boom folds or an attachment is raised. A route that works with the machine lowered is not automatically suitable for every operation. Treat the work envelope, not only the cab roof, as relevant.
Before the fictional field task, identify overhead lines and obtain reliable information for the actual route and operation. Prefer avoiding the line area. Where work near it cannot be avoided, involve the distribution network operator and competent planning for the required arrangements. This course does not supply a universal clearance, voltage estimate or rule based on the line's appearance. The model's dimensions cannot establish an electrical safety distance.
Share the plan with contractors and visiting operators, including designated routes, restrictions on raised equipment and stopping points. Do not place a tipping location or temporary store under a line because it is convenient. A sign or remembered route is not sufficient if the actual equipment or operation has changed. Visibility, lighting and how the operator maintains awareness of the line all need consideration within the actual method.
If an unidentified line or changed equipment creates uncertainty, hold the affected movement and obtain advice before approaching. Do not raise equipment to see how close it gets or send a helper to measure with a pole. Contact or suspected contact requires the established emergency response and urgent network/emergency assistance, keeping others away; this course is not a detailed vehicle-escape drill. Verification should confirm the agreed route and operation match the actual configuration and competent advice before work resumes. A previous incident-free pass cannot authorise a different raised task.
How can the ISO 45001 hierarchy of controls prevent electrical contact during equipment fault diagnosis?
Use HSE’s hierarchy to eliminate or substitute a hazard where practicable, then apply engineering and administrative controls before relying on PPE. Check each chosen control against the actual task and stop when it fails.
Use HSE’s hierarchy of controls: eliminate or substitute the hazard where possible, then use engineering and administrative controls; PPE is the last resort. Apply the sequence to the task and verify that each chosen barrier works. HSE hierarchy of controls (official source).
Electrical safety is a strong example of why the hierarchy matters. The best control is often to remove the need for live work, design equipment so live parts cannot be touched, use reduced voltage in high-risk conditions and isolate securely before maintenance. PPE can be important for some tasks, but it should not be the first or only control.
The hierarchy should be applied at design, procurement, installation, use, maintenance and decommissioning. If the workplace keeps relying on signs, briefings and PPE while equipment is unsuitable or poorly protected, the risk is not being controlled well.
An electrical fault is assessed before access; use competent personnel, suitable information and a method that avoids exposed live work.
How can the ERICPD hierarchy of controls prevent electrical contact during equipment fault diagnosis?
ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
Control level
Control for this activity
Owner and verification
Stop / restart decision
Eliminate
Use external diagnostics or remove the faulty equipment from use where that avoids exposed electrical work.
Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere.
If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Reduce, including substitution
Use a suitable off-line test or replaceable module where it safely proves the fault without exposed live conductors.
Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted.
Reject an alternative if its performance is unproved or its new hazards are unresolved.
Isolate
Securely isolate relevant supplies, prevent reconnection and prove dead using the approved safe-isolation method.
Release only after competent electrical owner accepts completed tests and safe reinstatement. Retain verification and unresolved restrictions at handover.
Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.
How can the ISO 45001 hierarchy of controls prevent electrical contact during equipment fault diagnosis?
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").
Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere.
If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Engineering controls
Use a suitable off-line test or replaceable module where it safely proves the fault without exposed live conductors.
Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted.
Reject an alternative if its performance is unproved or its new hazards are unresolved.
Engineering controls
Securely isolate relevant supplies, prevent reconnection and prove dead using the approved safe-isolation method.
Release only after competent electrical owner accepts completed tests and safe reinstatement. Retain verification and unresolved restrictions at handover.
Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.
Applied case
A trailer can pass beneath a line when lowered, but the proposed tipping point is under the span.
Decision and explanation
Avoid that tipping interface and obtain the competent/network-informed plan for the actual operation.
Raised configuration changes the envelope, and arcing can occur without contact.
Lesson 2
Ground condition is a changing control
Recognise when a route no longer supports the planned work.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Receive and unload identified palletised packaged goods from a rigid lorry using a suitable counterbalance forklift. Act: The supervisor checks the bay surface, lighting, pedestrian barriers, clear route and local unloading plan. Hold / review: Hold an unbooked vehicle, changed vehicle type, unknown load mass, damaged pallet or shifted load for the supervisor and, when needed, supplier or competent specialist.
Ground condition is a changing control
Soft ground, ruts, slopes and deteriorating edges can change a vehicle's stability and control. A field route suitable earlier can become unsafe after rain, repeated passes or erosion. The person driving may focus on the task rather than a wheel dropping towards an edge. Treat the current route and load as evidence, not the fact that the track is normally used.
At the fictional gateway, repeated traffic has deepened ruts beside a ditch. Review the route with competent knowledge of the actual machine, implement, load and ground. Avoid or improve unsuitable sections where practicable. The machine's manufacturer information and local assessment guide operation; this lesson does not prescribe a universal safe slope, speed or edge distance. A lower speed alone cannot make ground of unknown support suitable.
Plan a safe inspection method from appropriate positions and consider visibility, surface changes, turning and reversing. Do not send a person into a live vehicle path or near an unstable bank to obtain a measurement. Check whether an alternative route creates overhead-line, pedestrian or public-road concerns. A diversion must be assessed as a complete journey rather than accepted because it bypasses one rut.
Stop the affected work when deterioration exceeds the planned conditions or uncertainty prevents confirming suitability. The responsible person should arrange correction, a suitable alternative or rescheduling and verify the result before release. Encourage drivers to report shocks, loss of traction and near misses promptly, without treating them as proof of poor personal skill. For the exercise, describe the changed surface and credible overturn or loss-of-control path. Avoid calculating a safe angle from a model picture. A practical plan defines what change triggers a stop and who can decide whether the revised route is usable.
How do you check vehicle and route compatibility?
Check the whole vehicle–load–route combination. A vehicle fitting through a gate, holding a conformity mark or having an adequate nominal capacity does not prove that it can manoeuvre or handle this load safely.
A new delivery vehicle may pass the entrance but need a larger turning area, sweep its trailer over the footway or exceed the unloading equipment’s reach. Ask the supplier or carrier for actual dimensions, load information and operating instructions before accepting the task. HSE vehicle handling explains why size, manoeuvrability and visibility must be considered together. See HSE HSG136 third edition for the relevant source and scope.
Check
Decision to make
Dimensions and swept path
Confirm vehicle and load height, width, length and turning envelope against the entire route, overhead hazards and protected pedestrian space. (HSE)
Surface and stability
Verify bearing capacity, drainage, slopes and edges for the loaded vehicle and any stabilisers. An unknown cover, void or ground capacity requires a competent assessment. (HSE)
Load and handling equipment
Confirm load identity, mass, centre of gravity, packaging, capacity at the required reach or height, attachments and unloading sequence against the actual instructions. (HSE)
Visibility and protective systems
Check mirrors, cameras and other controls assumed by the plan. Their coverage and condition must suit the movement; alarms alone do not establish a clear route. (HSE)
Driver and maintenance
Check relevant competence, site familiarisation, vehicle checks and defect clearance. A road licence or supplier certificate alone does not settle these questions. (HSE)
Worked decision: a carrier substitutes an articulated lorry for the rigid lorry normally used. Its stated width is similar, so reception initially expects it to fit. The supervisor holds it at an agreed safe waiting point. The carrier’s turning information shows the trailer would cross the protected footway on the existing turn. The delivery is reassigned to a suitable vehicle or another assessed unloading arrangement; the pedestrian barrier is not removed to squeeze it through. Record the vehicle identity, route decision, agreed alternative and driver briefing.
For vehicles in use, HSG136 recommends daily driver checks before use and planned maintenance following manufacturer guidance. Check brakes, steering, tyres, lights, visibility aids, restraints, access steps and task-specific safety systems. A safety defect means taking the affected operation out of use until a competent person establishes and verifies a safe solution. A universal weekly route inspection rule is not justified; set route-check frequency from risk, deterioration, use and changes.
Applied case
Rain has softened the field edge and the usual wheel track now drops towards a ditch.
Decision and explanation
Stop and obtain a competent review or suitable alternative for the actual ground and machine.
Current ground and configuration govern suitability.
Lesson 3
Vehicle protection supports a suitable route
Keep overturn prevention and occupant protection distinct.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Receive and unload identified palletised packaged goods from a rigid lorry using a suitable counterbalance forklift. Act: The supervisor checks the bay surface, lighting, pedestrian barriers, clear route and local unloading plan. Hold / review: Hold an unbooked vehicle, changed vehicle type, unknown load mass, damaged pallet or shifted load for the supervisor and, when needed, supplier or competent specialist.
Vehicle protection supports a suitable route
Preventing overturn starts with suitable equipment, load, route and operation. Occupant protection limits consequences if an overturn occurs; it does not make unsuitable ground acceptable. A driver who feels secure in a cab can still be exposed by missing or defective protection or by a task beyond the vehicle's capability. Consider both prevention and the intended protective system.
For the fictional tractor, the responsible person should confirm suitability and condition for the actual field task, including required rollover protection and seat-restraint arrangements where relevant. Use the manufacturer's instructions and competent assessment, and repair defects before use. This course does not certify a cab, select retrofit structures or teach vehicle recovery. A seat belt must be considered with the actual protective system rather than as an isolated generic accessory.
The driver needs appropriate training, authorisation and information about the route and implement. Loads, raised attachments, turning and travel conditions can alter stability. Do not allow an unauthorised helper or passenger to ride in an unsuitable position. A course completion badge does not qualify a worker to drive a tractor or select an implement. Seasonal experience on another vehicle is useful context but does not prove competence for this configuration.
Before release, verify relevant pre-use checks, safe route conditions and the planned operating method. Stop if a critical defect, uncertain equipment suitability or changing ground undermines the arrangement. The supervisor should resolve pressures that encourage workers to bypass seat restraints or use the wrong machine. For the exercise, compare a suitable inspected configuration on an assessed route with a protected cab being used to justify deteriorated ground. The stronger answer keeps the route, machine and person controls working together and does not trade one safeguard for another.
How do you check vehicle and route compatibility?
Check the whole vehicle–load–route combination. A vehicle fitting through a gate, holding a conformity mark or having an adequate nominal capacity does not prove that it can manoeuvre or handle this load safely.
A new delivery vehicle may pass the entrance but need a larger turning area, sweep its trailer over the footway or exceed the unloading equipment’s reach. Ask the supplier or carrier for actual dimensions, load information and operating instructions before accepting the task. HSE vehicle handling explains why size, manoeuvrability and visibility must be considered together. See HSE HSG136 third edition for the relevant source and scope.
Check
Decision to make
Dimensions and swept path
Confirm vehicle and load height, width, length and turning envelope against the entire route, overhead hazards and protected pedestrian space. (HSE)
Surface and stability
Verify bearing capacity, drainage, slopes and edges for the loaded vehicle and any stabilisers. An unknown cover, void or ground capacity requires a competent assessment. (HSE)
Load and handling equipment
Confirm load identity, mass, centre of gravity, packaging, capacity at the required reach or height, attachments and unloading sequence against the actual instructions. (HSE)
Visibility and protective systems
Check mirrors, cameras and other controls assumed by the plan. Their coverage and condition must suit the movement; alarms alone do not establish a clear route. (HSE)
Driver and maintenance
Check relevant competence, site familiarisation, vehicle checks and defect clearance. A road licence or supplier certificate alone does not settle these questions. (HSE)
Worked decision: a carrier substitutes an articulated lorry for the rigid lorry normally used. Its stated width is similar, so reception initially expects it to fit. The supervisor holds it at an agreed safe waiting point. The carrier’s turning information shows the trailer would cross the protected footway on the existing turn. The delivery is reassigned to a suitable vehicle or another assessed unloading arrangement; the pedestrian barrier is not removed to squeeze it through. Record the vehicle identity, route decision, agreed alternative and driver briefing.
For vehicles in use, HSG136 recommends daily driver checks before use and planned maintenance following manufacturer guidance. Check brakes, steering, tyres, lights, visibility aids, restraints, access steps and task-specific safety systems. A safety defect means taking the affected operation out of use until a competent person establishes and verifies a safe solution. A universal weekly route inspection rule is not justified; set route-check frequency from risk, deterioration, use and changes.
Applied case
A driver says rollover protection means the tractor may continue over a newly unstable bank.
Decision and explanation
Occupant protection does not remove the need to avoid unsuitable ground and operate a suitable machine.
Prevent the overturn as well as providing the appropriate protective system.
Lesson 4
Whole-body vibration follows the entire driving day
Reduce repeated shocks before relying on exposure time alone.
The worker locates the lower back; the separate side view enlarges its bones, discs, nerve roots and nearby muscle.
Locate the lower back. How could the load, reach, route, equipment or work pattern be changed for the task in this lesson?
educational illustration · healthy anatomy; enlarged details and teaching colours.
Original SHAREhub schematic for the associated activity. The written lesson case supplies the decision evidence.
Whole-body vibration follows the entire driving day
Whole-body vibration and shocks can reach the driver through a vehicle travelling over rough ground. Repeated jolts, prolonged driving and awkward posture can contribute to back problems, while other factors such as manual handling also matter. A worker's report of discomfort deserves assessment and appropriate support, not an automatic diagnosis that vibration is the only cause.
The fictional route combines a rutted gateway, field passes and yard travel. Review the actual tasks, durations, machine condition, speed appropriate to conditions and seat adjustment. A model animation or manufacturer's generic emission value is not a measurement of this worker's real exposure. Competent assessment should address representative conditions and uncertainty, including unusual routes or tasks during the busiest period.
Stronger controls include improving suitable routes, reducing unnecessary travel, choosing appropriate equipment and maintaining vehicle and seat systems. Correctly adjusted suspension and a workable seating position support control but cannot erase severe ground shocks. Simply rotating a worker onto another high-vibration vehicle may not reduce their total exposure. Work scheduling and recovery should be based on the real assessment, not an invented universal safe driving time.
If the seat is defective or shocks exceed the planned conditions, report and restrict the affected task while the responsible person arranges correction. Verify the revised route and equipment under representative work without deliberately exposing a person to severe jolts for demonstration. Encourage early reports and confidential occupational or clinical advice where appropriate. For the exercise, map the main shock sources and compare route improvement with a reminder to sit straighter. Source reduction and maintenance change the exposure itself; posture advice alone leaves the rough journey and failed equipment in place.
How is a WBV assessment different?
Assess daily vibration in the dominant axis and consider shocks, route, vehicle and other back-pain factors; do not use HAV points or a hand-tool timer.
A non-specialist can often identify and reduce WBV risk by observing badly prepared surfaces, off-road work, repeated jolts, long static posture, awkward controls and manual handling. Use representative vehicle/task information and the longest credible daily duration where work varies. Measurement may be needed when the exposure category or control benefit remains uncertain, but a low A(8) estimate does not excuse severe avoidable shocks. See HSE.
Ask for separate daily x-, y- and z-axis assessments using the relevant frequency weightings and multiplying factors: 1.4 for each horizontal axis and 1.0 vertically, as specified in L141 Schedule 2. Combine all daily operating periods within each axis, then select the greatest daily result. The largest raw seat reading alone is not the daily exposure. The report should state axes, weightings, factors, durations, combined daily results, uncertainty and treatment of shocks. A competent assessor owns the method; a low A(8) does not excuse avoidable severe jolts.
Applied case
A worn seat and rutted gateway cause repeated jolts; the proposal is only to remind the driver about posture.
Decision and explanation
Improve the route and suitable vehicle/seat condition and assess the actual driving exposure.
Control the sources and actual exposure, not only the driver’s behaviour.
Lesson 5
Heat strain needs a workable task redesign
Connect workload, weather, clothing and usable recovery.
A worker and a separate enlarged skin section introduce sweating and the skin’s blood supply. Connect these structures to the work and environment described in the lesson.
Locate the sweat gland and skin vessels in the enlarged view. How should conditions, workload, clothing and recovery be managed together?
educational illustration · healthy anatomy; enlarged details and teaching colours.
Photorealistic illustrative UK workplace scene. Review checks: Hot task: Assess radiant load, humidity, work rate and the cooling limits of required PPE. Cold task: Move work to temperate space where feasible, or isolate refrigeration and verify the environment. Stock removal alone is not enough. Recovery and change: Provide suitable recovery and escape; stop and reassess when conditions or essential controls change.
Heat strain needs a workable task redesign
Heat strain depends on more than air temperature. Heavy effort, sunshine, humidity, clothing and limited cooling can affect how a worker manages body heat. A person who becomes dizzy or confused may also make an unsafe driving decision. Experienced workers are not immune, and an individual should not be expected to continue simply because others feel comfortable.
The fictional seasonal task has moved into the hottest part of the day, with water and shade far from the field. Review timing, workload, mechanical assistance, clothing requirements and practical recovery. Provide accessible drinking water, suitable breaks and a cooler or shaded recovery place as part of the assessed system. A bottle left at the farm office is not usable support for a worker whose task prevents returning there.
Plan supervision and communication so early concerns lead to action. Workers should stop the affected activity safely, tell the responsible person and obtain appropriate assistance when unwell. Suspected serious heat illness requires urgent emergency help through the actual first-aid procedure. This awareness course does not diagnose heatstroke, prescribe fluid quantities or provide a medical fitness decision. Individual health factors need confidential appropriate professional advice.
Verification checks that the revised work pattern and recovery facilities are genuinely usable during the busy period and that people understand the response. A forecast or thermometer alone cannot establish suitability for every person and task. Review changes in weather, workload or protective clothing and stop when the planned conditions are no longer met. For the exercise, compare moving heavy work to a suitable cooler period with telling workers to drink more while keeping every other demand unchanged. Protecting health is a management and task-design responsibility, supported by worker feedback rather than a test of personal endurance.
How should thermal risk be assessed?
Assessment should consider environment, task, clothing/PPE, work rate, duration, worker feedback, symptoms, vulnerable groups and evidence.
The assessment starts with the work, not the weather. Ask what the person is doing, how hard they are working, what clothing or PPE they must wear, how long exposure lasts, what recovery is available and what happens if they become impaired.
For complex heat stress, HSE notes that measurement may need occupational health or competent support and may involve techniques such as wet-bulb globe temperature (WBGT), metabolic-rate estimation, clothing insulation values, heart-rate measurement or physiological monitoring where other controls cannot be implemented.
Step
Practical question
Evidence
Define environment
Indoor, outdoor, process heat, cold store, vehicle cab or mixed?
Location/task map.
Identify thermal drivers
Temperature, radiant heat, air movement, humidity, PPE and work rate?
Observation and measurement.
Map people exposed
Who works there, for how long, and who may be more susceptible?
Roster and consultation.
Review task demand
Manual handling, pace, static work, shift length and recovery?
Task assessment.
Select controls
Engineering, scheduling, breaks, hydration, clothing/PPE and supervision.
Control plan.
Set stop triggers
Symptoms, failed ventilation, PPE intolerance, cold injury signs or weather change.
Briefing and supervisor card.
Verify
Worker feedback, observations, incidents, absence and monitoring reviewed.
Dashboard/action log.
Neither the GB indoor guidance of normally 16°C, or 13°C for rigorous work, nor the similar Northern Ireland guidance is an outdoor work limit or a universal stop-work threshold. There is no legal maximum temperature. Any local work/rest or entry criteria must come from the actual task assessment, PPE and competent advice, then be checked against worker response. HSE law summary; HSENI temperature guidance.
Applied case
A worker becomes dizzy during heavy outdoor work and is told to finish the last field pass.
Decision and explanation
Stop the affected activity safely, obtain appropriate assistance and review the heat-control arrangement.
Illness requires protective action and appropriate help, not endurance.
Lesson 6
A changed day needs a changed plan
Join route, equipment and health information before restart.
Related SHAREhub topic guide. Apply its prompts to the specific case below.
A changed day needs a changed plan
The field-work plan can become outdated within a shift. Rain changes ground, an implement changes height, a seat defect changes vibration and rising heat changes physical demand. Treat these reports as connected work information. A supervisor who looks only at completed pre-use forms may miss that the task now differs from the conditions those forms described.
The fictional coordinator should ask what has changed, who is affected and which controls no longer match. Check the actual machine and implement configuration, route, ground and line interfaces. Review the whole driving day and the practical availability of water, shade and recovery. Workers and contractors should know where they can wait safely and whom to contact if a restriction prevents the intended task.
Make specific holds rather than one vague instruction to be careful. The raised-equipment operation awaits a competent line-avoidance plan; the deteriorated track awaits route review; the defective seat awaits repair and exposure reassessment; an unwell worker needs appropriate assistance. Do not average these gaps into an acceptable overall score. A favourable condition in one area does not compensate for a critical failure in another.
Restart follows the required correction and authorised verification, with the revised method communicated to those doing the work. A safe observation and worker feedback can test whether the arrangement remains usable under representative conditions. For the transfer exercise, write a fictional change log that distinguishes observation, protective response, owner and evidence needed before release. Do not submit a real vehicle inspection or claim competence for network advice or medical assessment. The useful outcome is a plan that adapts when reality changes, without asking the driver to improvise around physical or health hazards alone.
How should uncertainty be handled?
Uncertainty should be recorded, challenged and reduced before decisions rely on weak assumptions.
Risk assessment is not a guessing competition. If exposure levels are unknown, plant condition is uncertain, worker competence is unproven or the credible worst case is disputed, the assessment should say so and assign action. Sometimes the right decision is to stop the task until information improves.
Uncertainty can also come from change: new contractors, unusual weather, temporary equipment, production pressure, out-of-hours work, altered layout or maintenance backlogs.
Uncertainty
Why it matters
Action
Unknown exposure
Health risk cannot be judged reliably.
Commission monitoring or use a more protective control.
Unknown plant condition
Safeguards may not work when needed.
Inspect, test and verify before operation.
Unknown competence
People may not recognise loss of control.
Check training, authorisation and supervision.
Unknown interface
Two teams may create risk for each other.
Hold coordination meeting and agree control ownership.
Unknown emergency route
Response may fail under pressure.
Drill, test and update emergency plan.
Applied case
The route, attachment and weather have all changed since the morning briefing.
Decision and explanation
Reassess the affected conditions and verify suitable revised arrangements before release.
Readiness depends on the actual current task, not only its earlier description.
Lesson 7
Plan field work around overhead electricity
Assess the highest operating configuration, not just travel height.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Receive and unload identified palletised packaged goods from a rigid lorry using a suitable counterbalance forklift. Act: The supervisor checks the bay surface, lighting, pedestrian barriers, clear route and local unloading plan. Hold / review: Hold an unbooked vehicle, changed vehicle type, unknown load mass, damaged pallet or shifted load for the supervisor and, when needed, supplier or competent specialist.
Understand the activity and how harm develops
The raised equipment approaches overhead lines along the field edge. Electricity can be dangerous before direct contact, and equipment height changes with tipping, folding or raised attachments. Ground levels, rutting and line conditions affect the available clearance. This illustration cannot establish a safe clearance for a real site.
Map lines before work and involve the electricity network operator where necessary to define the safe arrangement. Routes, storage and loading positions should prevent raised equipment entering the restricted area. The emergency brief matters too: touching a vehicle involved with an electrical line can expose a helper, so people must keep away and call emergency services and the network operator.
A worker stands beside a separate anatomical overview of the heart, lungs, muscles and nerves. These normal tissues introduce the injury lesson; no electrical current path is shown.
Locate the heart, muscles and nerves as different living tissues. Follow the lesson’s isolation and competence boundaries before any intervention.
educational illustration · healthy anatomy; enlarged details and teaching colours.
Recognise the evidence boundary
Question
Case evidence
What is observed?
A contractor plans to tip a trailer beneath a line crossing the yard.
How can harm occur?
Electricity could arc to raised equipment and kill people nearby.
What information is needed?
Check the line location and full equipment operating envelope.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Relocate the operation or obtain DNO-agreed safe arrangements.
Accountable work arrangement
Avoid work and vehicle routes near overhead lines where possible. Identify lines and obtain competent network-operator advice for required work near them. Control routes, equipment configurations and any assessed barriers or goalposts. Brief operators and contractors on restrictions and the planned response to line contact or damage.
Release verification
Confirm the actual route and tipping area meet the agreed plan.
Apply this at work
Review lines for combines, telehandlers, irrigation pipes, bale stacks and every visiting high vehicle.
How do you design safer routes and choose controls?
Map actual movements, remove unnecessary vehicle–pedestrian contact, then protect unavoidable interfaces. Physical separation and suitable layout come before signs, high-visibility clothing and expectations that people will always react correctly.
Observe the site at busy and quiet times. Draw staff routes to toilets, welfare and exits alongside forklifts, lorries, customer cars, waste collections and emergency access. Include a pedestrian’s natural walking route, not just the route drawn on the plan. A long detour that encourages shortcuts needs redesign, not repeated reminders. See HSE workplace transport risk assessment for the relevant source and scope.
Remove or reduce the movement: relocate a collection point, use drive-through arrangements or keep deliveries outside public access periods where practicable.
Separate by design: provide suitable pedestrian routes, barriers, separate doors and protected waiting areas. Select barriers for the foreseeable impact; a painted line is not a crash barrier.
Control remaining crossings: use visible, accessible crossing points away from reversing areas, suitable lighting, clear priority and enough visibility and stopping distance.
Support the design: brief routes, control access and delivery timing, supervise and enforce locally assessed speed limits. Select task-appropriate protective equipment for residual risks.
Routes must suit the largest vehicle and load that will actually use them, including turns, slopes, headroom and ground-bearing capacity. Keep surfaces drained and clear; protect vulnerable racking, fuel equipment and edges. Temporary routes need the same risk-based scrutiny. HSE HSG136 third edition (pages 9–13) provides the design principles.
There is no single safe speed, lane width or pedestrian clearance for every yard. The vehicle, load, bends, visibility, surface and users determine the decision. A posted limit is a maximum within the local system, not permission to drive at that speed when conditions are worse. HSE site speed limits describes choosing and enforcing site limits.
Applied case
A contractor proposes tipping beneath the lines because the empty trailer passed underneath safely.
Decision and explanation
Use an agreed safe tipping location outside the line risk area.
An observer cannot establish electrical clearance by eye or prevent arcing as the trailer rises. Passing in travel configuration does not validate tipping. The raised configuration needs the planned location and network advice where relevant. Dry weather does not remove the overhead electrical hazard or establish a suitable clearance.
Lesson 8
Match the machine to ground and slope
Familiar routes need reassessment when ground or loads change.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Receive and unload identified palletised packaged goods from a rigid lorry using a suitable counterbalance forklift. Act: The supervisor checks the bay surface, lighting, pedestrian barriers, clear route and local unloading plan. Hold / review: Hold an unbooked vehicle, changed vehicle type, unknown load mass, damaged pallet or shifted load for the supervisor and, when needed, supplier or competent specialist.
Understand the activity and how harm develops
The tractor route has deteriorated near a slope. Ruts, soft edges and changes in load or attachment height affect stability. A route that worked earlier in the season may no longer be suitable after rain. The model is an illustration, so its slopes cannot set safe operating limits for real equipment.
Consider the whole combination, ground condition and planned manoeuvres, using manufacturer limits and competent assessment. The safest decision may be a different route or postponed task. Roll-over protection and the restraint arrangement support protection if an overturn occurs, but they do not make unsuitable ground acceptable or justify crossing a collapsing edge.
Recognise the evidence boundary
Question
Case evidence
What is observed?
Recent rain has deepened ruts along a sloping field shortcut.
How can harm occur?
Loss of stability could overturn the tractor and injure its operator.
What information is needed?
Assess changed ground conditions against equipment capability and the route plan.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Choose a suitable route and vehicle with required rollover protection and restraint.
Accountable work arrangement
Choose a suitable machine, attachment and route for the actual ground and task. Avoid steep, soft, rutted or unstable edges and postpone work when conditions exceed the safe plan. Maintain suitable roll-over protection and use the appropriate restraint as required for the equipment. Control speed, loading and attachment position under the manufacturer and site-specific arrangements.
Release verification
Recheck the route before use and stop when conditions deteriorate.
Apply this at work
Apply this to silage clamps, field gateways, ditch edges and trailer unloading points.
How do you design safer routes and choose controls?
Map actual movements, remove unnecessary vehicle–pedestrian contact, then protect unavoidable interfaces. Physical separation and suitable layout come before signs, high-visibility clothing and expectations that people will always react correctly.
Observe the site at busy and quiet times. Draw staff routes to toilets, welfare and exits alongside forklifts, lorries, customer cars, waste collections and emergency access. Include a pedestrian’s natural walking route, not just the route drawn on the plan. A long detour that encourages shortcuts needs redesign, not repeated reminders. See HSE workplace transport risk assessment for the relevant source and scope.
Remove or reduce the movement: relocate a collection point, use drive-through arrangements or keep deliveries outside public access periods where practicable.
Separate by design: provide suitable pedestrian routes, barriers, separate doors and protected waiting areas. Select barriers for the foreseeable impact; a painted line is not a crash barrier.
Control remaining crossings: use visible, accessible crossing points away from reversing areas, suitable lighting, clear priority and enough visibility and stopping distance.
Support the design: brief routes, control access and delivery timing, supervise and enforce locally assessed speed limits. Select task-appropriate protective equipment for residual risks.
Routes must suit the largest vehicle and load that will actually use them, including turns, slopes, headroom and ground-bearing capacity. Keep surfaces drained and clear; protect vulnerable racking, fuel equipment and edges. Temporary routes need the same risk-based scrutiny. HSE HSG136 third edition (pages 9–13) provides the design principles.
There is no single safe speed, lane width or pedestrian clearance for every yard. The vehicle, load, bends, visibility, surface and users determine the decision. A posted limit is a maximum within the local system, not permission to drive at that speed when conditions are worse. HSE site speed limits describes choosing and enforcing site limits.
Applied case
Rain has undermined the edge of the usual field track. A loaded tractor is waiting.
Decision and explanation
Stop and reassess the route, load and ground before selecting an alternative.
Changing attachment height can affect stability and does not establish that the ground will support the combination. The changed conditions require a new decision before the machine enters the unstable section. The marks record earlier use, not the present strength of the edge after deterioration.
Lesson 9
Reduce vibration and shocks at source
Verify reduced exposure at the task, not only the purchase of equipment.
Original SHAREhub schematic for the associated activity. The written lesson case supplies the decision evidence.
Understand the activity and how harm develops
Repeated field runs take the driver over rough ground. Whole-body vibration reaches the seated operator through the vehicle, while sudden shocks can occur at ruts and gateways. The exposure depends on the route, vehicle, seat adjustment, speed and duration together. A newer seat alone does not establish an adequately controlled day.
Compare the actual harvesting schedule with the route condition and driver work pattern. The task can be changed through ground maintenance, suitable vehicles, seat setup and less continuous rough-ground driving. Reporting discomfort and obtaining appropriate occupational health advice support the plan; workers should not be expected to accept pain as an unavoidable part of farm work.
Recognise the evidence boundary
Question
Case evidence
What is observed?
A driver repeatedly crosses deep ruts in a worn-seat tractor.
How can harm occur?
Sustained shocks and vibration could worsen back injury.
What information is needed?
Check route condition, vehicle setup and the exposure assessment.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Improve the surface and vehicle setup and plan lower-exposure work.
Accountable work arrangement
Reduce rough-ground journeys and maintain travel routes where practicable. Select and maintain suitable vehicles, suspension and seats for the task. Set up the seat correctly and use suitable speed and driving techniques for conditions. Assess exposure across the shift and organise work, breaks and symptom reporting accordingly.
Release verification
Check seat condition and whether the revised route reduces shocks.
Apply this at work
Combine field, road and yard driving when reviewing an operator working day.
How is a WBV assessment different?
Assess daily vibration in the dominant axis and consider shocks, route, vehicle and other back-pain factors; do not use HAV points or a hand-tool timer.
A non-specialist can often identify and reduce WBV risk by observing badly prepared surfaces, off-road work, repeated jolts, long static posture, awkward controls and manual handling. Use representative vehicle/task information and the longest credible daily duration where work varies. Measurement may be needed when the exposure category or control benefit remains uncertain, but a low A(8) estimate does not excuse severe avoidable shocks. See HSE.
Ask for separate daily x-, y- and z-axis assessments using the relevant frequency weightings and multiplying factors: 1.4 for each horizontal axis and 1.0 vertically, as specified in L141 Schedule 2. Combine all daily operating periods within each axis, then select the greatest daily result. The largest raw seat reading alone is not the daily exposure. The report should state axes, weightings, factors, durations, combined daily results, uncertainty and treatment of shocks. A competent assessor owns the method; a low A(8) does not excuse avoidable severe jolts.
Applied case
A driver has a replacement seat but still reports repeated severe jolts at the same gateway.
Decision and explanation
The gateway, speed, vehicle setup and task exposure together.
Tolerance and production demand do not determine whether the exposure is adequately controlled. The persistent jolts identify a route and operating problem that a seat replacement alone has not resolved. Price does not establish suitability or control of the actual shocks transmitted on the route.
Lesson 10
Plan seasonal work for heat strain
Heat controls need a responsive work plan and a clear escalation route.
Photorealistic illustrative UK workplace scene. Review checks: Hot task: Assess radiant load, humidity, work rate and the cooling limits of required PPE. Cold task: Move work to temperate space where feasible, or isolate refrigeration and verify the environment. Stock removal alone is not enough. Recovery and change: Provide suitable recovery and escape; stop and reassess when conditions or essential controls change.
Understand the activity and how harm develops
The outdoor worker has a long physical task in warm weather. Heat load depends on exertion, humidity, sunlight, clothing and personal factors as well as air temperature. A worker arriving for the season may be unfamiliar with the routine or reluctant to ask for a break. The scene asks whether the schedule and welfare arrangements make heat controls practical.
Plan work before symptoms occur: change timing, reduce effort, provide shade and accessible drinking water, and ensure a way to report illness. Supervisors need a response for someone becoming unwell, including emergency help for severe symptoms. A bottle in a distant vehicle is not effective access if workers cannot leave their task safely.
Recognise the evidence boundary
Question
Case evidence
What is observed?
A seasonal worker looks unwell after extended work without accessible shade.
How can harm occur?
Heat and exertion could lead to serious heat illness.
What information is needed?
Ask about symptoms, workload, weather and access to water and rest.
Protect, manage and verify
Purpose
Practical application
Immediate protection
Stop affected work, provide appropriate aid and implement the heat plan.
Accountable work arrangement
Reschedule strenuous tasks to more suitable conditions and reduce unnecessary physical effort. Provide accessible drinking water, shaded rest and suitable welfare. Adapt work-rest arrangements and supervision to the task, weather and individual needs. Brief workers on symptoms, early reporting and how to obtain prompt first aid or emergency help.
Release verification
Confirm recovery support and revised conditions before authorising work.
Apply this at work
Apply the plan to grain stores, workshops and enclosed cabs as well as outdoor harvesting.
What should happen before, during and after heat or cold work?
Plan the specific task and conditions, verify controls at the workface, pause when symptoms or safeguards change, and hand back only after people and controls are checked.
These are SHARE example decision routes, not legal temperature or exposure-time limits. The supervisor sets task-specific arrangements with affected workers and contractors; specialist input is needed where heat load, cold exposure, PPE or health factors make ordinary judgement unreliable. Required protective equipment for another hazard must not be removed just to feel cooler.
Outdoor roof repair; roofers, scaffolders and people below, in sun and changing weather.
Check forecast and workface conditions, physical effort, fall protection, shade, drinking water, cool recovery, communication and rescue access. Brief the crew and contractor.
Supervisor checks effort, breaks and worker feedback; reschedule or reduce strenuous work if heat load rises. Hold for approval if weather or programme changes.
Stop and give first aid for dizziness; move cool, stay with the person and offer water only if fully alert and able to swallow. Confusion, collapse or other heatstroke signs: call 999 immediately, without waiting 30 minutes. Account for the crew and review controls only after care is underway; verify before restart.
Cold-store picking; pickers and maintenance staff exposed to cold air, draughts and cold products.
Check door control, warming area, dry suitable clothing and gloves, task duration, dexterity needs and lone-worker communication.
Check fingers, coordination and shivering; use assessed warm-up and rotation. Hold if a refrigeration or door fault changes exposure.
Stop and move to shelter for numbness or soaked clothing; seek first-aid and medical help if frostbite is suspected. Confusion, slurred speech or slow breathing after cold exposure suggests hypothermia: call 999 immediately, without waiting for a thermometer. Record defects and verify controls only after care is underway.
Non-routine chemical cleaning in a warm plant room; maintenance crew and process operator in impermeable PPE/RPE.
Confirm chemical controls and PPE compatibility, ventilation, entry/exit method, cool recovery, drinking opportunity, buddy contact and a task-specific work/rest plan.
Buddy and supervisor check symptoms and overrun; hold at the agreed reassessment point if temperature, humidity, workload or PPE changes.
Stop for nausea or unsafe PPE use; exit the controlled area safely, give first aid and cool the person. Poor coordination, confusion, collapse or other heatstroke signs: call 999 now. Account for everyone, then record decontamination and review the method before hand-back.
Changed condition: heat source, cold wind, wet clothing or failed HVAC on a shared site.
Identify who owns the area and the affected contractors; confirm a working escalation contact and available alternative work or location.
Pause and reassess the six factors and exposed people. Manager or competent assessor approves a revised method before restart.
Do not restart on an unchanged assessment. If anyone has symptoms, provide first aid first; call 999 immediately for suspected heatstroke or hypothermia. Then record the fault, worker consultation, repair and recheck.
Applied case
A worker becomes confused and very unwell during strenuous work in the heat.
Decision and explanation
Stop work, call 999 immediately, help the person cool and follow emergency instructions.
Continuing exertion delays help when the symptoms may indicate a serious heat illness. Confusion and severe illness require prompt emergency response. Protect the person from further heat exposure while following professional guidance. Leaving an unwell person without observation or prompt care can delay recognition of deterioration and needed treatment.
Lesson 11
The afternoon field change
Decide what can proceed after route, equipment and heat conditions change.
Related SHAREhub topic guide. Apply its prompts to the specific case below.
The afternoon field change
The fictional farm switches a tractor to a taller attachment for afternoon work. The usual route passes an overhead line and the planned unloading point requires raised equipment. Rain has softened a gateway beside a ditch. The driver reports repeated jolts from a worn seat, and a seasonal worker is dizzy after heavy work in rising heat. The supervisor has a signed morning briefing for a different machine configuration and asks whether it can cover the change.
Start by describing the new conditions. Raised equipment changes the line interface and electricity can arc without direct contact. Soft ground and a ditch change stability and control. Repeated shocks concern the actual route, vehicle and working day. Heat illness concerns workload, weather, clothing, recovery and the individual's condition. None of these can be settled by a favourable model view or an incident-free morning.
Hold the affected work and obtain appropriate assistance for the unwell worker, stopping their activity safely. Use the actual first-aid and emergency arrangements if serious illness is suspected. Do not diagnose the person or prescribe a fixed fluid amount. Review work timing, effort and accessible recovery rather than asking for one last task. Make sure a safe location and communication are available while the work is restricted.
For overhead lines, prefer a route and operation that avoid the interface, and obtain distribution-network and competent advice where needed. Do not estimate clearance from the lowered travelling position or raise the equipment as a test. The actual configuration, operation and location need the correct plan. For ground, arrange competent review and a suitable alternative, improvement or rescheduling. Lower speed and a protective cab do not make uncertain support adequate.
Address the seat and vibration exposure through suitable maintenance, equipment and route changes with representative assessment. A generic vehicle rating or posture reminder does not verify the revised driving day. Check appropriate occupant protection, pre-use condition and operator competence for the machine and attachment. Seasonal familiarity is not a substitute for the actual task information and authorisation.
The final release statement identifies each hold, responsible role and required evidence. Update the briefing so contractors and workers understand the changed route, restrictions, recovery arrangements and stop triggers. Verify the correction through suitable safe checks; do not deliberately drive the unstable edge or approach a line to collect evidence. A practice result supports understanding but cannot authorise a vehicle, establish an electrical clearance or determine medical fitness. The case is resolved when the work plan matches the real field conditions and people can use it without improvising around unresolved hazards.
How should the basic risk assessment process work?
The process should identify hazards, decide who may be harmed, evaluate risk, record significant findings and review the controls.
The familiar five-step model is only useful when each step is done honestly. Walking the workplace, checking incident data, speaking to workers, reviewing maintenance, reading safety data sheets and observing non-routine work will usually reveal more than a desk exercise.
The output should be understandable to the people who use it. A supervisor should know what must be in place before work starts. A worker should know the task controls and stop-work triggers. A manager should know what resources and review evidence are required.
Step
What good looks like
Evidence
Identify hazards
Task observation includes normal, abnormal, maintenance, cleaning and emergency conditions.
Walkthrough notes, worker input and hazard register.
Decide who may be harmed
Employees, contractors, visitors, public, vulnerable workers and emergency responders are considered.
People-at-risk section and consultation evidence.
Evaluate risk
Existing controls are tested, not assumed.
Inspection findings, monitoring data, maintenance records and competence checks.
Record findings
Significant risks, controls, action owners and review triggers are clear.
Assessment, action tracker and risk register.
Review
Assessment changes after incidents, changes, new information or weak control evidence.
The supervisor proposes keeping the morning plan because the same driver is available.
Decision and explanation
Hold the affected tasks and verify revised line, ground, equipment, vibration and heat arrangements.
The current configuration and conditions require review; competence does not cancel physical or health hazards.
Lesson 12
Take a verified action into the workplace
Connect one actual task to an owner, evidence and a clear release or escalation decision.
Related SHAREhub topic guide. Apply its prompts to the specific case below.
Turn awareness into a practical question
Great Britain farm-work awareness. Confirm the relevant national fire, environmental and pesticide route. Specialist livestock, machinery, electrical, work-at-height, pesticide, confined-space and rescue tasks require their actual competent assessment and authorisation; this course confers none.
Choose one relevant operation from the course. Describe the person or environment at risk, the mechanism of harm and the exact condition that needs controlling. Separate an observation from a conclusion. A display, signature, badge or clean appearance answers only a limited question.
Use the included practice resources to prepare a fictional task brief, risk review or verification question. Decide which competent role owns the decision and which evidence must be available before work restarts or work is released. Keep worker protection, public exclusion, task acceptance and environmental decisions distinct where required.
At work, use your actual approved arrangements. Report uncertainty and preserve the relevant hold, restriction or safe state while it is resolved. Confirm that the action addressed the original harm route and check whether another shift, load, cleaning task or maintenance change could reintroduce it.
Course completion records awareness learning. It does not establish practical competence, certify an organisation or authorise specialist, clinical, maintenance, chemical or emergency work.
How should the basic risk assessment process work?
The process should identify hazards, decide who may be harmed, evaluate risk, record significant findings and review the controls.
The familiar five-step model is only useful when each step is done honestly. Walking the workplace, checking incident data, speaking to workers, reviewing maintenance, reading safety data sheets and observing non-routine work will usually reveal more than a desk exercise.
The output should be understandable to the people who use it. A supervisor should know what must be in place before work starts. A worker should know the task controls and stop-work triggers. A manager should know what resources and review evidence are required.
Step
What good looks like
Evidence
Identify hazards
Task observation includes normal, abnormal, maintenance, cleaning and emergency conditions.
Walkthrough notes, worker input and hazard register.
Decide who may be harmed
Employees, contractors, visitors, public, vulnerable workers and emergency responders are considered.
People-at-risk section and consultation evidence.
Evaluate risk
Existing controls are tested, not assumed.
Inspection findings, monitoring data, maintenance records and competence checks.
Record findings
Significant risks, controls, action owners and review triggers are clear.
Assessment, action tracker and risk register.
Review
Assessment changes after incidents, changes, new information or weak control evidence.