Slurry, silage and dangerous-atmosphere decisions

Free online training · Approximate learning time: 90–140 minutes · Self-paced

Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.

Lesson 1

Agitation changes the atmosphere risk

Explain why a familiar slurry area cannot be judged safe by smell.

How should confined spaces risk management be organised? — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Agitation changes the atmosphere risk

Slurry can release gases produced during decomposition. Mixing can release them rapidly, affecting people near openings and in connected or poorly ventilated spaces. Some gases can be toxic or displace oxygen; some can burn. A person does not have to climb into a tank to be exposed. The relevant area can include a building over storage or a low space beside the mixing point.

At the fictional mixing station, the operator is asked to judge readiness by whether the usual smell has disappeared. Smell is not a reliable safety test, and a changing odour does not establish a breathable atmosphere. A clear model picture supplies no concentration reading. Equally, a portable detector is not permission to stand in the release area: rapid gas release may not give adequate warning. Monitoring, where specified, belongs within competent arrangements rather than replacing exclusion and safe planning.

The responsible person should use a suitable procedure for the actual storage, machinery, buildings, people and livestock. Aim to avoid entry and keep people outside areas that may be affected, with appropriate planned ventilation and access control. Equipment condition and the means of operating it without exposure need review before work. Changes in layout or adjacent activity can invalidate a familiar routine, so contractors and other workers need coordinated information.

If conditions or controls are uncertain, hold the operation and obtain competent advice rather than conducting a brief trial beside the opening. Report facts such as the proposed mixing point, open access and nearby occupied building. Later access must follow the responsible competent person's procedure, not an invented elapsed time in this course. Verification concerns the actual planned controls and affected area. Do not experiment with gas release, lean over an opening to inspect or use a person's symptoms as a test of the atmosphere.

How should risk assessment and planning be governed?

Risk assessment should be task-specific and governed by a standard that requires no-entry review, specified-risk analysis, control selection and rescue planning.

Generic confined-space assessments are weak because the hazard changes with the space, contents, previous contents, task, tools, connected systems, weather, ventilation and people involved. The governance standard should require a fresh or reviewed assessment for each entry or class of repeated entry where conditions are genuinely controlled and equivalent.

Planning should integrate maintenance work orders, process isolation, contractor method statements, permits, gas testing, equipment readiness, emergency response and hand-back. If these elements are managed separately, gaps appear at the interfaces.

Planning and assessment controls
Planning pointWhat to requireEvidence
ScopeExact space, work and duration.Work order and task risk assessment.
No-entry decisionReasonably practicable alternatives considered.No-entry review record.
Specified risksAtmosphere, engulfment, drowning, fire, explosion and entrapment considered.Assessment with hazard basis.
InterfaceOperations, maintenance, contractors and emergency teams coordinated.Planning meeting or permit interface.
ChangeTriggers for reassessment defined.Stop-work and reassessment criteria.
ReviewLessons and weak signals captured after the job.Post-entry review for higher-risk work.

Applied case

A worker says the mixer can start because the strong smell has faded and a detector is available.

Decision and explanation

Neither smell nor carrying a detector replaces the competent exclusion and operating plan.

Rapid releases and unreliable sensory judgement require preventive arrangements, not a smell test.

Lesson 2

The affected area extends beyond the tank

Coordinate buildings, livestock and people before mixing.

How should confined spaces risk management be organised? — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

The affected area extends beyond the tank

A gas release can reach someone who believes they are working on a separate task. The fictional slurry store lies beside a cattle building and a route used for feed delivery. A door left open for convenience can connect activity to an area with restricted air movement. A barrier around the liquid opening addresses falling but does not automatically protect the person in the adjacent building.

Before the task, identify storage and connected spaces, possible gas movement and every person or animal that could be affected. Use competent knowledge of the actual system and conditions, including the means of ventilation and how buildings are occupied. Weather is one factor in a suitable plan, not a universal permission rule. This course does not specify a wind speed, clearance distance or waiting period that makes any slurry site safe.

Coordinate simultaneous work. A contractor collecting equipment, a stock worker entering a shed or a driver using the route must know the relevant restriction and safe alternative. Put access controls where people decide to enter, and make the responsibility for maintaining them clear. A sign cannot close an open route by itself. Do not ask an unprotected observer to stand in a potentially affected area as the way of keeping others out.

If the required ventilation, exclusion, livestock arrangements or communication cannot be established, mixing remains held. Changes during work require the planned stop and reassessment. Before access later resumes, the responsible competent person must establish the required conditions through the actual procedure. A clock or absence of visible fumes is insufficient. For the exercise, mark the occupied areas and access paths on a fictional plan and state the uncertainty that prevents release. Protecting the whole affected area is more reliable than assuming people will recognise an invisible hazard after they enter it.

How should management of change protect confined-space controls?

Management of change should review whether modifications, process changes, contractor changes or maintenance methods create new confined-space risks.

Confined-space risk often changes quietly. A new chemical, inerting method, cleaning product, access hatch, drain connection, ventilation arrangement, work method, contractor or production schedule can invalidate old assumptions. Management of change should ask whether the space classification, register, isolation plan, gas-testing method, rescue plan or training need has changed.

Temporary changes are just as important. A breakdown, blockage, abnormal residue, flooding, heatwave, shutdown or rushed maintenance window can turn a familiar entry into a different risk profile.

Change triggers
ChangeConfined-space concernAction
Plant modificationNew access, connections or residues.Update register, drawings and controls.
Process or substance changeDifferent gases, vapours or oxygen effects.Review assessment and gas detection.
Maintenance method changeNew tools, hot work, solvents or duration.Reassess entry and permit conditions.
Contractor changeDifferent competence or rescue capability.Review selection and induction.
Emergency or abnormal conditionUnplanned atmosphere, flooding or blockage.Stop, reassess and escalate.
Learning from eventExisting controls may be unreliable.Revise standard and verify implementation.

Applied case

A slurry opening is fenced but a maintenance worker plans to enter the connected barn during agitation.

Decision and explanation

The whole affected-area restriction and competent access plan, including the barn.

Atmosphere exposure can extend beyond the liquid opening and interact with adjacent work.

Lesson 3

Opening protection must survive the work

Distinguish fall prevention from atmosphere control.

Guarded mobile platform beside a UK industrial building. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Inspect ageing rooflights without stepping on a suspect roof. Act: Review fragility and whether an internal or MEWP method can reach the task; exclude people below. Hold / review: Hold if roof strength, route or protection is uncertain or wind exceeds the equipment limit.

Opening protection must survive the work

An uncovered slurry opening can expose a person to a fall and drowning as well as a dangerous atmosphere. Removing a cover for mixing or collection changes the physical protection. A chain, temporary plank or remembered instruction may not stop someone stepping or falling into the opening. The person operating equipment can also be distracted by hoses or a passing vehicle.

The fictional collection task needs suitable secure covers, guarding or barriers that remain effective throughout the planned operation. Assess the opening, access, equipment movement and who could approach, including children and visitors. Avoid creating an unprotected gap while positioning a mixer or connecting a tanker. A fall-protection arrangement must be designed for the actual forces and task; this course does not specify a universal barrier dimension or teach improvised edge construction.

Compare two different controls. Physical opening protection prevents entry or falling; atmosphere exclusion and competent operating arrangements prevent exposure to gas. Having one does not prove the other. A securely fenced pit may still expose someone standing in an affected building, while good ventilation does not close a hole. Both pathways need explicit ownership and verification in the same plan.

If protection is missing or disturbed, stop or restrict the affected activity through the agreed safe method, keep people clear and obtain the responsible person's correction. Do not reach across the opening to place a loose board or test a questionable cover with body weight. Verification should confirm the installed protection is suitable, secure and compatible with the work before access resumes. The exercise report states the opening, stage of operation, exposed route and current restriction. A completed checklist cannot replace a missing physical safeguard, and a photograph cannot establish that a cover is structurally adequate.

How does the work lead to harm?

A person may step through a rooflight, fall from an unprotected edge or opening, slip from unsuitable access equipment, or be struck by an object dropped from above. Distance, landing surface and obstruction affect injury, but a short fall can still be severe. Deterioration, weather and changed routes can defeat yesterday’s plan; identify the fall path and everyone below before selecting equipment.

Identify the source, route to the person, early signal, strongest practicable control and stop decision. Test that decision in real work and after change.

How does the work lead to harm? decision table
ExposureHarm routeControl and hold point
Fragile rooflight or sheetThe surface gives way and a person falls through into the space below.Treat as fragile until a competent check proves otherwise; use protected access and exclusion.
Edge, opening or ladderA slip or overreach leads to a fall onto a hard or obstructed landing.Work from ground where possible; otherwise use a suitable guarded platform and stop if edge or access control fails.
Dropped tool or materialA person below is struck even though the worker above remains protected.Prevent falling objects, segregate the drop zone and stop when exclusion cannot be maintained.

Sources: HSE introduction to working at height safely; HSE roof work; HSENI working at height

Applied case

A cover is removed for the tanker hose and only a loose plank marks the gap.

Decision and explanation

Keep access restricted until suitable opening protection for the operation is established.

Atmosphere control does not prevent falling into an unprotected opening.

Lesson 4

Keep ignition and slurry work coordinated

Recognise flammable-gas concerns without inventing a hazardous zone.

Workers reviewing a permit beside safely isolated industrial equipment. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Small paint store: Keep minimum stock, use a suitable flammable cabinet, segregate incompatible materials, close containers, remove contaminated waste and inspect the store. Paint spraying booth: LEV/ventilation, Ex equipment, booth maintenance, storage limits, ignition control and cleaning. LPG cylinder cage: Store upright in a ventilated cage, segregate full/empty/damaged cylinders, protect from impact, control smoking/hot work and check valves/hoses.

Keep ignition and slurry work coordinated

Slurry gas can present a fire or explosion pathway as well as a toxic atmosphere. An ignition source near a release may affect people who are concentrating on the mixing task. In the fictional farm, a workshop repair with a grinder is proposed beside the access route while slurry is agitated. Treat the conflicting activities as a planning question before either task begins.

The competent assessment must identify dangerous substances, possible releases, ventilation and relevant ignition sources. It determines the necessary separation, equipment and controls for the actual conditions. This lesson does not assign a hazardous-area zone or a numerical safe distance from a model. Nor does removing one obvious flame prove every source of ignition is controlled. Electrical equipment, hot surfaces and other work may be relevant according to the assessment.

Compare preventing the conflict with relying on emergency response. Rescheduling or relocating incompatible work can remove exposure more reliably than placing an extinguisher nearby. Any relocation must itself be checked; moving a grinder to the other side of an opening is not a demonstrated solution. Explain restrictions to contractors and those responsible for workshop work so they cannot unknowingly reintroduce the ignition source.

If conflicting work begins unexpectedly, use the agreed safe stop and reporting arrangements while remaining outside affected areas. Do not enter to disconnect equipment or retrieve tools from a dangerous atmosphere. The responsible person should verify that the corrected work plan and controls remain effective throughout the operation and before later access. For the exercise, identify the release pathway, potential ignition and people affected, then choose a no-conflict plan with a clear owner. The absence of a previous fire is not evidence that simultaneous work is acceptable, and an extinguisher does not substitute for preventing the release and ignition combination.

How should ignition sources be controlled?

Ignition control should cover electrical, static, hot surfaces, hot work, vehicles, mechanical friction, sparks and human behaviours.

Ignition control is often reduced to a no-smoking sign, but DSEAR requires a much broader view. A vapour cloud or dust cloud may be ignited by static discharge, non-rated electrical equipment, portable tools, hot bearings, welding, grinding, vehicles, heaters, lightning or mechanical impact.

Controls should be built into design and work planning. Hot work, temporary electrical equipment, contractor activities, maintenance and abnormal operations are especially important because they introduce ignition sources into areas where normal controls may be disrupted.

Ignition source controls
Ignition source Control Evidence
Ignition sourceHot work ControlPermit-to-work, gas testing, isolation, cleaning, fire watch and handback. EvidencePermit records and supervisor checks.
Ignition sourceStatic electricity ControlBonding, earthing, suitable hoses, controlled transfer rates and antistatic materials. EvidenceInspection records and resistance checks.
Ignition sourceElectrical equipment ControlSuitable Ex equipment in hazardous areas and inspection/maintenance. EvidenceEx register and inspection reports.
Ignition sourceHot surfaces ControlTemperature control, insulation, maintenance and surface temperature review. EvidenceInspection records and design data.
Ignition sourceMechanical sparks/friction ControlTool selection, bearing maintenance, guarding and housekeeping. EvidenceMaintenance records and defect reports.
Ignition sourceVehicles ControlTraffic controls, diesel engine rules, battery charging controls and exclusion zones. EvidenceSite rules, charging assessment and inspection.
Ignition sourceSmoking/naked flames ControlNo-smoking rules, controlled designated areas and supervision. EvidenceSignage, induction and inspection records.

HSE DSEAR guidance supports ignition-source control: HSE DSEAR background.

Applied case

A contractor proposes grinding beside the slurry area because there is no open flame.

Decision and explanation

Hold the conflict and obtain the assessed ignition-control and simultaneous-work arrangement.

Potential ignition needs competent review; prevention is stronger than relying on response.

Lesson 5

Do not go beneath silage sheeting

Keep retrieval and maintenance outside the atmospheric pocket.

How should confined spaces risk management be organised? — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Do not go beneath silage sheeting

Silage can generate gases, and a sheet can trap an atmosphere that cannot support safe breathing. Restricted space can also make escape difficult. A small object beneath the sheet does not make the exposure small. The fictional worker who leans or crawls underneath to retrieve a tool may place their breathing zone in danger before they can recognise what is wrong.

Never crawl beneath silage clamp sheeting. Plan the task so it can be carried out without entering the pocket, using a competent assessment of an external method where appropriate. The method must also address the clamp edge, unstable material and the forces involved in moving a sheet. A long tool is not automatically safe if its use requires leaning over an exposed edge or dragging the person towards the opening.

Do not use appearance, smell or a short exposure time as clearance. Gases around clamps can also affect nearby low or poorly ventilated areas, so the responsible person must consider the actual arrangement. This course does not teach a waiting period, atmosphere-test sequence or permission to enter after ventilation. Where a task would require entry into a dangerous space, stop and refer it to the competent specialist planning route rather than adapting this awareness lesson into an operating method.

If a tool or sheet cannot be dealt with by a suitable external arrangement, leave it and maintain the restriction while advice is obtained. Property recovery is not a reason to expose a worker. Verify that the selected method keeps people outside the atmospheric and fall hazards for its entire use, including collection and return. The fictional exercise asks learners to compare an external planned method with a quick crawl, explaining why speed and familiarity do not provide protection. No person should enter beneath a sheet to demonstrate the risk or to obtain an illustrative photograph.

How can the organisation avoid entry?

Make no-entry a design and work-planning decision, with a recorded reason before any permit is considered.

For drain inspection, use a remote camera and external cleaning point if a competent assessment confirms that method is safe. For tanks, provide fixed gauges, sampling points or clean-in-place systems where practicable. Check that pressure, chemical use or jetting does not create a new uncontrolled exposure. The manager signs the selected method; if entry remains necessary, the confined-space lead records why alternatives cannot safely achieve the task. This is the elimination level of the five-level hierarchy and ERICPD, ahead of isolation, engineering, procedures and PPE.

Applied case

A mobile phone lies just inside the silage sheet and a worker offers to crawl in briefly.

Decision and explanation

Do not crawl beneath the sheet; arrange a suitable assessed external solution or leave the item restricted.

The sheet can conceal a dangerous atmosphere and restricted escape; item value does not justify entry.

Lesson 6

Rescue must not create another casualty

Choose non-entry alarm and access protection within the learner’s role.

How should confined spaces risk management be organised? — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Rescue must not create another casualty

Someone collapsing near slurry or silage may trigger an immediate urge to follow them. The same invisible atmosphere can overcome the person attempting rescue. A companion, rope or general first-aid qualification does not by itself establish a safe rescue capability. Emergency arrangements must be planned for the actual hazards before the work, with competent resources rather than a promise that someone will improvise.

The awareness response is to raise the alarm, summon emergency assistance and prevent others entering the danger area while staying safe. Give the location, access route, suspected slurry or silage atmosphere and number of people involved. Follow the emergency operator's instructions and the site's competent plan. This course does not teach entry rescue, breathing-apparatus use or an improvised retrieval technique. Do not enter simply to check breathing or attach a line.

An effective plan considers communications, access for responders, who meets them and how other workers and livestock are kept clear. Remote areas may need reliable location information beyond a farm name. Test the communication and response arrangement by safe exercises, not by placing a volunteer in a hazardous space. No one should assume emergency-service attendance removes the need for planned suitable rescue arrangements where specialist entry work is actually necessary.

After an incident, keep the affected activity restricted. Restart requires investigation, competent assessment and authorised verification of the necessary controls, not recovery of the person or disappearance of a smell. Support workers and preserve factual information without exposing anyone for evidence collection. For the fictional drill, distinguish what an ordinary observer can safely do from what requires trained equipped responders. A good answer describes a prompt alarm and protective boundary, and explicitly refuses a dangerous entry that could turn one casualty into several.

How should rescue capability be governed?

Rescue capability should be treated as a controlled emergency function with defined people, equipment, maintenance, drills and review.

Rescue arrangements need the same discipline as entry controls. The organisation should know which types of entry require non-entry retrieval, internal rescue, breathing apparatus, specialist contractors, external emergency-service liaison or a combination. The plan should match the geometry of the space and the likely condition of the casualty.

Drills should test credible scenarios, not comfortable ones. A good drill asks whether communications work, whether equipment reaches the casualty, whether the casualty can be extracted through the access point, whether rescuers are protected and whether the response time is realistic.

Rescue capability governance
CapabilityManagement requirementEvidence
Rescue plan libraryPlans matched to space classes and tasks.Task-specific rescue sheets.
PeopleCompetent rescue personnel available during entry.Training, authorisation and rota.
EquipmentSuitable and maintained retrieval, BA/RPE, communication and first-response kit.Inspection and maintenance records.
DrillsScenario-based practice and debrief.Drill report and action close-out.
External liaisonEmergency services know site access and hazards where relevant.Emergency plan and liaison notes.
ReviewWeaknesses escalated and resourced.Management review and improvement plan.

Applied case

A colleague collapses near a slurry opening and another worker wants to enter with a rope.

Decision and explanation

Raise the alarm, summon emergency help and keep people out while remaining safe.

An unplanned entry can expose the rescuer to the same atmosphere. Use the emergency plan and competent responders.

Lesson 7

Treat slurry mixing as a gas-release operation

Do not turn one atmospheric casualty into several through an improvised rescue.

How should confined spaces risk management be organised? — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Understand the activity and how harm develops

Agitation can release dangerous gases from slurry into the working space and connected buildings. A worker on the surface may be affected without entering the store. In this scene the mixer is beside livestock accommodation, so the assessment must include animals, adjacent rooms and anyone who may arrive after mixing starts. Smell is not a reliable basis for declaring access safe.

The teaching decision is about exclusion and controlled access, not finding a quick way to inspect the tank. A person who collapses can draw colleagues into the same atmosphere. Emergency arrangements must be planned in advance and must prevent an improvised entry rescue. A quiet mixer or apparently clear air does not prove a safe atmosphere.

Recognise the evidence boundary

QuestionCase evidence
What is observed?Slurry agitation starts below a livestock building with people nearby.
How can harm occur?Released gases could rapidly cause unconsciousness or death.
What information is needed?Request the mixing plan and identify every connected occupied space.

Protect, manage and verify

PurposePractical application
Immediate protectionExclude people and animals under the assessed slurry procedure.
Accountable work arrangementAvoid entry into slurry stores and use a planned external method for the work. Apply the assessed mixing procedure, clearing people and animals from affected spaces and controlling all access. Manage ventilation, equipment position and access restrictions through the competent farm-specific plan. If someone collapses, keep clear, call emergency services and prevent unplanned entry; use the prearranged rescue arrangements.
Release verificationA responsible competent person controls any later access under that procedure.

Apply this at work

Apply the same entry-avoidance and rescue planning principles to tanks, pits, silos and enclosed drains.

How can the organisation avoid entry?

Make no-entry a design and work-planning decision, with a recorded reason before any permit is considered.

For drain inspection, use a remote camera and external cleaning point if a competent assessment confirms that method is safe. For tanks, provide fixed gauges, sampling points or clean-in-place systems where practicable. Check that pressure, chemical use or jetting does not create a new uncontrolled exposure. The manager signs the selected method; if entry remains necessary, the confined-space lead records why alternatives cannot safely achieve the task. This is the elimination level of the five-level hierarchy and ERICPD, ahead of isolation, engineering, procedures and PPE.

Applied case

A colleague collapses beside an opening during mixing. Another worker starts climbing down to help.

Decision and explanation

Keep people out, call 999 from safety and activate the planned response.

A rope does not provide a breathable atmosphere or a planned rescue system and may create another casualty. Preventing further exposure is essential. Specialist rescue arrangements must deal with the atmospheric hazard before entry. Odour cannot establish that the atmosphere is safe, and it cannot authorise rescue entry.

Lesson 8

Maintain protection at slurry openings

Protection must continue through setup, operation and reinstatement.

Select the work method before equipment
Teaching graphic from the linked SHAREhub source section.

Understand the activity and how harm develops

The mixer access opening is uncovered beside the working route. A person can fall while handling a hose, stepping backwards or walking in poor light. Slurry conceals depth and offers no firm footing; rescue is complicated further by gas and machinery hazards. Being a strong swimmer is not an effective control.

Consider the whole operation, including moving the mixer into place, removing temporary protection and tanker collection afterwards. The scene asks whether suitable covers or barriers protect the opening throughout those changes. A warning sign cannot prevent someone stepping into a gap while concentrating on another task, and a loose sheet may create the appearance of a cover without its strength.

Recognise the evidence boundary

QuestionCase evidence
What is observed?An access opening beside the mixer is left unprotected.
How can harm occur?A person could fall into slurry and drown.
What information is needed?Check all openings and the arrangements for work around the mixer.

Protect, manage and verify

PurposePractical application
Immediate protectionSecure suitable covers or barriers and exclude unauthorised access.
Accountable work arrangementKeep openings securely covered when access is not needed, using suitable load-bearing covers. Provide effective edge protection and controlled access during authorised opening work. Plan hose and equipment positions so workers do not need to step across the opening. Provide lighting, housekeeping and emergency arrangements that account for slurry gas and drowning hazards.
Release verificationConfirm protection remains effective throughout mixing and collection.

Apply this at work

Use this lifecycle check for grain pits, service chambers and other temporarily opened floor voids.

How do you apply avoid, prevent, minimise?

First avoid work at height where reasonably practicable. If it remains, prevent falls using a safe existing place or suitable equipment. Only then minimise the distance and consequences of a remaining fall.

At each level, consider collective protection before personal protection. A short lanyard configured as restraint prevents reaching an edge; fall arrest permits a fall and needs verified clearance and rescue. Neither makes an unsafe roof sound.

OrderExampleDecision test
AvoidInspect a roof from below or use extendable tools.Can the task be done safely without going up?
Prevent, collectiveGuarded scaffold, tower or suitable MEWP.Can everyone at risk be protected without an individual action?
Prevent, personalVerified work-restraint system.Is the person unable to reach a fall position?
Minimise, collectiveSafety net close below the work.Is competent installation and inspection possible?
Minimise, personalDesigned fall-arrest system.Are anchor, compatibility, clearance and timely rescue verified?

Sources: Work at Height Regulations 2005; Work at Height Regulations (Northern Ireland) 2005; HSE introduction to working at height safely; HSE assessing all work at height

Applied case

The tanker driver needs the opening uncovered for a hose and proposes leaving it open until the next collection.

Decision and explanation

Protect the opening during use and secure its suitable cover when access ends.

An unverified board may fail or shift while suggesting the opening is protected. The plan maintains physical protection through the changing task and reinstates the secured cover before the area is released. A cone and word-of-mouth warning do not maintain effective fall protection for everyone approaching the area.

Lesson 9

Exclude ignition from slurry gas release

Coordinate simultaneous work before it defeats the mixing controls.

Air receiver, relief fittings and protected compressed-gas storage. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Flour silo, connected dust filter and transfer duct at a food-processing site. Act: Reduce dust release and ignition; confirm material test data, filter and silo volumes, vent discharge path, duct connections and protection design basis. Hold / review: Stop transfer if a critical collector fails, a vent is obstructed, isolation is impaired or changed ducting has not been reassessed.

Understand the activity and how harm develops

The portable heater stands close to the mixing point. Slurry gas can create an ignition hazard as well as a toxic atmosphere. Equipment that seems harmless in open air may be unsuitable at the release point or in a connected enclosed space. The scenario links the gas assessment to the choice and position of temporary equipment.

Before mixing, identify possible ignition sources introduced by workers and contractors, including hot work and electrical equipment. Do not infer a safe zone from the drawing or a fixed arbitrary distance. A competent assessment must account for the actual system and conditions, with controls communicated to everyone who might bring equipment into the area.

Recognise the evidence boundary

QuestionCase evidence
What is observed?A portable ignition source is placed beside the slurry mixing point.
How can harm occur?Flammable gas could ignite and injure nearby people.
What information is needed?Check the mixing assessment for ignition and equipment controls.

Protect, manage and verify

PurposePractical application
Immediate protectionExclude ignition sources and use the assessed equipment and work method.
Accountable work arrangementRemove unnecessary ignition sources and defer incompatible nearby work. Use the assessed equipment and layout for the mixing operation. Control contractor access and temporary heaters, lights and electrical equipment. Include gas release, ventilation and emergency arrangements in the competent operation plan.
Release verificationConfirm ignition controls before and during the operation.

Apply this at work

Apply the same ignition-source review around fuel transfer, grain dust and chemical stores.

How should dust extraction and powder handling systems be protected?

Dust systems should be protected by preventing dust escape, controlling ignition, maintaining extraction and using relief, isolation or suppression where needed.

Dust extraction and powder systems can create both process risk and building risk. A leak, blocked filter, failed housekeeping regime or modified duct can allow dust to accumulate. The primary explosion may start inside equipment, but the worst harm may occur when settled dust becomes airborne in a secondary explosion.

Protection should be chosen from the actual system: collectors, silos, mills, dryers, conveyors, filters, elevators, hoppers and ducts may each need different controls. A competent assessment should identify where ignition could occur and how an event could propagate.

Dust system controls - Dust system controls
System part Risk Control
Dust collector Explosion inside filter housing. Relief, isolation and maintenance.
Ductwork Explosion propagation. Isolation and cleaning access.
Silo or bin Dust cloud ignition during filling or discharge. Venting, grounding and ignition control.
Conveyor Flame propagation and hot bearing ignition. Bearing monitoring and isolation.
Milling or grinding Heat, sparks and fine dust generation. Temperature, tramp metal and process controls.
Workroom surfaces Secondary explosion fuel. Housekeeping and dust-layer inspections.

Applied case

A contractor wants to grind a bracket beside the slurry mixing point while agitation continues.

Decision and explanation

Stop the conflicting work and obtain competent coordination of the gas and ignition risks.

An extinguisher is a response measure; it does not prevent an explosive atmosphere being ignited. The proposed simultaneous activity introduces ignition into a release operation and needs the assessed controls before it can proceed. Odour does not establish safe atmospheric conditions or a suitable hot-work location.

Lesson 10

Do not enter beneath silage sheeting

A visible route is not proof of a safe atmosphere.

How should confined spaces risk management be organised? — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Understand the activity and how harm develops

The lost tool is beneath the sheet. A worker might see only a short crawl, but the space can contain a hazardous atmosphere and offer limited movement or escape. Disturbing the sheet or material can change the conditions. Someone watching outside cannot establish breathable air inside.

This is a retrieval-planning problem: keep people outside and obtain a competent external method. A casual decision to enter can bypass the farm arrangements for confined or otherwise dangerous atmospheres. If a person becomes unresponsive, the response must prevent others entering the same space. The value of the tool is not a reason to improvise entry or rescue.

Recognise the evidence boundary

QuestionCase evidence
What is observed?A worker suggests crawling under the sheet to recover a tool.
How can harm occur?Trapped gases or oxygen depletion could cause collapse.
What information is needed?Ask for a retrieval method that keeps people outside the sheeted space.

Protect, manage and verify

PurposePractical application
Immediate protectionPrevent entry beneath sheeting and arrange a safe external method.
Accountable work arrangementPrevent access beneath the sheet and use a suitable external retrieval method. Keep the area controlled while a competent person assesses the retrieval task. Include atmosphere, unstable material and restricted escape in any specialist assessment. Maintain emergency communications and prohibit improvised entry rescue.
Release verificationConfirm the item is recovered without exposing anyone to the atmosphere.

Apply this at work

Use this challenge whenever an object is lost in a pit, tank, silo or enclosed void.

How can the organisation avoid entry?

Make no-entry a design and work-planning decision, with a recorded reason before any permit is considered.

For drain inspection, use a remote camera and external cleaning point if a competent assessment confirms that method is safe. For tanks, provide fixed gauges, sampling points or clean-in-place systems where practicable. Check that pressure, chemical use or jetting does not create a new uncontrolled exposure. The manager signs the selected method; if entry remains necessary, the confined-space lead records why alternatives cannot safely achieve the task. This is the elimination level of the five-level hierarchy and ERICPD, ahead of isolation, engineering, procedures and PPE.

Applied case

A worker suggests a quick crawl under the sheet while a colleague holds their boots.

Decision and explanation

Stop the entry and seek a safe external retrieval arrangement.

Holding someone boots does not control the atmosphere, material movement or restricted access. Keeping people outside avoids that exposure. Breath-holding is not an atmospheric protection method and cannot establish a safe entry or rescue system. Light can show objects but cannot show oxygen levels or establish the absence of harmful gases.

Lesson 11

Mixing day: a connected-space decision

Keep slurry, silage retrieval and emergency planning within safe boundaries.

How should confined spaces risk management be organised? — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Mixing day: a connected-space decision

The fictional farm plans slurry agitation while a contractor repairs equipment nearby. The mixer opening is uncovered for positioning, a barn side door is open and cattle work is scheduled inside the connected building. A grinder is plugged in at the workshop entrance. Meanwhile a worker wants to recover a phone from beneath the silage sheet. A colleague says that the smell is normal and the gas detector has not alarmed. These exercise facts require separate decisions within one coordinated plan.

Describe the harm routes rather than treating the detector as a general green light. Agitation may release dangerous gas rapidly; restricted ventilation and connections can expose someone outside the tank. The opening creates a fall and drowning route. Some slurry gases may ignite when an appropriate source is present. The silage sheet can trap a dangerous atmosphere and restrict escape. The actual concentrations and safety of access cannot be established from the model, smell or an uneventful previous mixing session.

Hold the affected operations until the responsible competent person has established the appropriate plan. Protect the opening with suitable arrangements for the equipment and keep people and livestock outside the affected areas. Coordinate barn work, access routes and contractor activity so they cannot defeat the restrictions. Resolve the ignition conflict through the assessed work plan, including rescheduling or suitable relocation where appropriate. Do not send a worker into the area to unplug the grinder if that itself creates exposure.

The phone retrieval is a separate no-entry decision. Nobody crawls beneath the silage sheet. A competent review may identify an external method that also controls edge and handling risks; otherwise leave the item and retain the restriction. Do not invent a waiting period or a detector reading that grants permission. This lesson is awareness and coordination, not an entry or gas-monitoring procedure.

Before any work, check the emergency arrangements. The caller needs an exact location and safe access information; someone must know how to warn others and meet responders without entering the danger area. If a person collapses, raise the alarm and call emergency assistance promptly while remaining safe. A rope, willing helper or ordinary first-aid role cannot substitute for competent equipped rescue planning. Prevent a spontaneous second entry rather than asking a learner to practise one.

The release statement should identify what remains held, who owns each correction and what competent verification is required before operation or later access. Weather, ventilation, equipment and simultaneous work changes belong in that review. A completed permit or checklist records decisions but does not create a safe atmosphere. Safe observation and communication exercises can test the arrangement without producing gas or placing a person at an opening. The case is resolved by a workable no-entry system and a credible emergency response, never by guessing that the task will be short enough to avoid harm.

How should risk assessment and planning be governed?

Risk assessment should be task-specific and governed by a standard that requires no-entry review, specified-risk analysis, control selection and rescue planning.

Generic confined-space assessments are weak because the hazard changes with the space, contents, previous contents, task, tools, connected systems, weather, ventilation and people involved. The governance standard should require a fresh or reviewed assessment for each entry or class of repeated entry where conditions are genuinely controlled and equivalent.

Planning should integrate maintenance work orders, process isolation, contractor method statements, permits, gas testing, equipment readiness, emergency response and hand-back. If these elements are managed separately, gaps appear at the interfaces.

Planning and assessment controls
Planning pointWhat to requireEvidence
ScopeExact space, work and duration.Work order and task risk assessment.
No-entry decisionReasonably practicable alternatives considered.No-entry review record.
Specified risksAtmosphere, engulfment, drowning, fire, explosion and entrapment considered.Assessment with hazard basis.
InterfaceOperations, maintenance, contractors and emergency teams coordinated.Planning meeting or permit interface.
ChangeTriggers for reassessment defined.Stop-work and reassessment criteria.
ReviewLessons and weak signals captured after the job.Post-entry review for higher-risk work.

Applied case

The detector is quiet, and the contractor asks to finish grinding while the mixer starts.

Decision and explanation

Maintain the hold until competent atmosphere, opening, exclusion, ignition and emergency arrangements are established.

A detector and human lookout cannot replace prevention and competent coordination of the whole affected area.

Lesson 12

Take a verified action into the workplace

Connect one actual task to an owner, evidence and a clear release or escalation decision.

How should confined spaces risk management be organised? — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Turn awareness into a practical question

Great Britain farm-work awareness. Confirm the relevant national fire, environmental and pesticide route. Specialist livestock, machinery, electrical, work-at-height, pesticide, confined-space and rescue tasks require their actual competent assessment and authorisation; this course confers none.

Choose one relevant operation from the course. Describe the person or environment at risk, the mechanism of harm and the exact condition that needs controlling. Separate an observation from a conclusion. A display, signature, badge or clean appearance answers only a limited question.

Use the included practice resources to prepare a fictional task brief, risk review or verification question. Decide which competent role owns the decision and which evidence must be available before work restarts or work is released. Keep worker protection, public exclusion, task acceptance and environmental decisions distinct where required.

At work, use your actual approved arrangements. Report uncertainty and preserve the relevant hold, restriction or safe state while it is resolved. Confirm that the action addressed the original harm route and check whether another shift, load, cleaning task or maintenance change could reintroduce it.

Course completion records awareness learning. It does not establish practical competence, certify an organisation or authorise specialist, clinical, maintenance, chemical or emergency work.

How should risk assessment and planning be governed?

Risk assessment should be task-specific and governed by a standard that requires no-entry review, specified-risk analysis, control selection and rescue planning.

Generic confined-space assessments are weak because the hazard changes with the space, contents, previous contents, task, tools, connected systems, weather, ventilation and people involved. The governance standard should require a fresh or reviewed assessment for each entry or class of repeated entry where conditions are genuinely controlled and equivalent.

Planning should integrate maintenance work orders, process isolation, contractor method statements, permits, gas testing, equipment readiness, emergency response and hand-back. If these elements are managed separately, gaps appear at the interfaces.

Planning and assessment controls
Planning pointWhat to requireEvidence
ScopeExact space, work and duration.Work order and task risk assessment.
No-entry decisionReasonably practicable alternatives considered.No-entry review record.
Specified risksAtmosphere, engulfment, drowning, fire, explosion and entrapment considered.Assessment with hazard basis.
InterfaceOperations, maintenance, contractors and emergency teams coordinated.Planning meeting or permit interface.
ChangeTriggers for reassessment defined.Stop-work and reassessment criteria.
ReviewLessons and weak signals captured after the job.Post-entry review for higher-risk work.

Applied case

The shift action log says “training completed, issue closed”. It records no condition check, work status or task owner.

Decision and explanation

The accountable person verifies the task-specific control and records the justified decision.

Learning supports the decision; evidence that the relevant control works is needed before the responsible person closes the action.