Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Full course outline and access routes.
Lesson 1
Start with the setting and the shared responsibilities
Compare the receiver, hazards and procedures in two delivery environments.
A delivery crosses an organisational boundary
The tanker operator controls the vehicle and driver arrangements, while the receiver controls important parts of the delivery location and storage system. A safe transfer requires cooperation before arrival and at the point of delivery. Agree the access, receiving arrangements, contact, public protection and emergency response. Neither party can assume that the other has dealt with every hazard simply because the delivery is routine or has happened before.
At a petrol filling station, unloading involves a volatile product, a public forecourt and a designed tank/fill and vapour-control arrangement. HSE L133 specifically addresses those petrol deliveries and the responsibilities of the site operator, road-tanker operator and driver. It is not a manual for loading at the distribution terminal. The driver and receiving staff must use their actual approved method, including any arrangements for assisted or unassisted deliveries.
A private heating-oil delivery has different receiver equipment, access and product conditions. The tank may be above ground, the fill point remote from the vehicle and the hose route close to a house, garden or public path. Heating oil still creates fire, exposure and substantial pollution risk. Its properties and transfer method must be checked from the actual product and instructions; lower volatility than petrol does not make uncontrolled delivery safe.
Planning should allow a real refusal or delay when conditions are unsafe. Give drivers usable pre-delivery information and a route to resolve discrepancies without pressure to improvise. A customer instruction, familiar address or valid order does not prove tank condition, capacity or correct connection. Where evidence is missing, record the reason for the hold and obtain a suitable decision before transfer rather than treating completion of the delivery as the default outcome.
What evidence should be available for transfer operations?
Evidence should prove the transfer system is safe today, not just that a procedure exists.
Assurance follows one actual transfer: product and tank identity, vehicle immobilisation, hose test, barrier functional check, start authorisation, level trend, stop event and hand-back. Sample records and observe the bay; a signed form alone does not prove the connection was right.
Evidence
What it should show
Failure to challenge
Transfer procedure
Correct sequence for line-up, transfer, monitoring, abnormal response and handback.
Procedure differs from field equipment.
Barrier register
Critical safeguards, owners, tests, impairments and performance standards.
No owner for overfill or ESD protection.
Hose/coupling register
Compatibility, inspection, testing, service life and defect control.
Hoses stored badly or used beyond inspection date.
dangerous-substances fire/explosion assessment
Explosive atmosphere formation, ignition control and emergency mitigation.
Area classification not matched to actual transfer conditions.
Training and authorisation
Operators, drivers, supervisors and contractors know critical steps.
Generic induction with no transfer-specific assessment.
Incident and weak-signal review
Leaks, drips, alarms, near misses and aborted transfers are trended.
Small leaks normalised as housekeeping problems.
Applied case
A dispatcher gives a heating-oil driver a petrol-forecourt unloading checklist because both jobs involve a tanker. The driver recognises that the receiving tank, pump method, access and emergency arrangements differ and requests the correct delivery procedure and customer information.
Decision and explanation
The receiving equipment, product behaviour and transfer arrangements need their own assessed method.
Some principles transfer, but the actual procedure must fit the product and equipment. Customer status does not remove driver or operator responsibilities.
Look closer
Explore the numbered equipment and control points. Existing SHAREhub teaching schematic; illustrative and not to scale.Coordinate delivery
Agree the product, tank, capacity, responsibilities and protected access before release.
Petrol forecourt
Verify the receiver and the applicable vapour-return and shutdown arrangements for the actual petrol delivery.
Private heating-oil customer
Check tank condition, containment, the hose route, drains and safe access. The two receiving settings need their own checks.
01 · Read the situation
A dispatcher gives a heating-oil driver a petrol-forecourt unloading checklist because both jobs involve a tanker. The driver recognises that the receiving tank, pump method, access and emergency arrangements differ and requests the correct delivery procedure and customer information.
02 · Explain the principle
The tanker operator controls the vehicle and driver arrangements, while the receiver controls important parts of the delivery location and storage system. A safe transfer requires cooperation before arrival and at the point of delivery. Agree the access, receiving arrangements, contact, public protection and emergency response. Neither party can assume that the other has dealt with every hazard simply because the delivery is routine or has happened before.
03 · Carry it into work
Some principles transfer, but the actual procedure must fit the product and equipment. Customer status does not remove driver or operator responsibilities.
Lesson 2
Prove the product, connection and available capacity
Explain why independent agreement of delivery evidence is required.
Three agreements before the valve opens
Correct delivery begins with agreement between the ordered product, the vehicle compartment and the identified receiving tank. Use the required documents, compartment identification and site markings, checking that they describe the same transfer. A single readable label is helpful but does not resolve a conflicting record. Wrong-grade delivery can contaminate stock, create unsuitable use and lead to costly or hazardous recovery, even if no liquid escapes.
Then verify the receiving connection and route using the authorised procedure. Closely spaced fill points, damaged labels, altered pipework and poor lighting can defeat assumptions based on memory. Do not rely on the position of yesterday’s hose or a customer pointing toward a cap. If the identity cannot be established, hold the delivery and escalate. A diagram may help, but it must match the actual installation and current identification.
Safe capacity means the amount that may be received under the approved operating arrangement, not the tank’s nominal total volume. Existing stock, the intended delivery quantity and required working limits must agree using reliable information. Gauge or stock records that disagree need resolution. Overfill protection is an additional barrier, not permission to deliver an uncertain quantity. Never assume a device will correct a wrong tank selection or stop every possible release.
At the private heating-oil tank, condition and venting also matter before transfer. Signs of damage, leakage, unstable support or an obstructed vent need the specified assessment, rather than a hopeful reduction in delivery rate. The model does not provide tank design limits or inspect hidden defects. Use the operator’s criteria and authorised technical support, document the hold accurately, and resume only after a verified safe receiving arrangement is established.
How should loading, unloading and transfer operations be controlled?
Transfer operations should verify substance, route, receiving capacity, connection, supervision and emergency isolation before flow starts. See HSE HSG176 storage of flammable liquids in tanks
Tank transfer is where many tank farm incidents begin. The task can involve road tankers, rail tankers, ships, pipelines, pumps, flexible hoses, couplings, manifolds, shared routes and changing shift ownership. The risk is not only a leak; it is wrong tank, wrong product, overfill, static ignition, hose failure, incompatible mixing or delayed isolation.
A good transfer procedure is usable at the point of work. It defines who authorises transfer, who checks line-up, how ullage is confirmed, what communication is required, what happens if an alarm sounds, how flow is stopped, and what handover is needed if transfer spans shifts.
Where drivers or contractors are involved, site rules must be clear. A contractor should not be expected to infer a site's tank farm hazards from a generic induction.
Substance verification. Confirm identity, compatibility and receiving tank. Delivery note, SDS and tank label.
Line-up. Verify valves, hoses, pumps and route before transfer. Line-up checklist and independent check.
Capacity. Confirm safe ullage against planned volume. Tank level record and safe fill limit.
Connection. Use compatible, inspected hoses and couplings. Hose register and pre-use checks.
Supervision. Monitor level, flow, alarms and abnormal conditions. Transfer log and operator rounds.
Handover. Communicate live transfers across shift changes. Shift log and permit/transfer status.
What if the transfer indications do not agree?
A discrepancy between expected transfer, tank level and observed flow is a reason to investigate the receiving route and instrumentation through the assessed procedure. Do not average inconsistent indications, assume that the more convenient one is correct or extend the planned transfer because the normal gauge appears unchanged. Identify who can stop the incoming flow safely and who has authority to resolve the uncertainty.
For an illustrative tanker receipt, the operator notices that the receiving-tank indication does not match the expected transfer trend. Follow the site’s validated stopping and isolation arrangement, communicate with the driver and keep the affected transfer held while competent personnel establish the actual tank, route, receiving capacity and instrument condition. Check whether other connected operations share the uncertainty or protection. Restart requires an authorised decision based on restored, verified conditions and a revised transfer plan where necessary; the next shift must receive the held status and unresolved facts, not simply an unfinished delivery quantity.
Guidance and scope: Original SHARE transfer-discrepancy example applying HSE GB flammable-liquid storage and overfill guidance. Actual stopping sequence, response margin and restart evidence are plant-specific; no universal discrepancy tolerance or trip set point is supplied. HSE HSG176 storage of flammable liquids in tanksHSE large-tank safety alert
Applied case
The forecourt order specifies one grade, but the fill-point label and the site stock record disagree. A staff member says the label was probably swapped during recent works. The driver keeps the transfer on hold until the correct tank, route and safe capacity are independently resolved through the approved arrangement.
Decision and explanation
Hold transfer and resolve the actual product, tank, route and capacity before starting.
A small wrong delivery is still a wrong delivery. Independent agreement and a correct receiving route are prerequisites, not matters to investigate after opening the transfer.
Look closer
Photorealistic illustrative UK workplace scene. Review checks: Threat: Wrong destination, uncertain capacity or failed receipt controls can create an overfill demand. Preventive function: Verify sensing, logic/power and final stop, including configuration, proof-test scope and common dependencies. Normal indication is separate. Consequences and mitigation: A release may spread, ignite or affect the environment. Bunds, drainage, ignition control and response have distinct functions and limits.01 · Read the situation
The forecourt order specifies one grade, but the fill-point label and the site stock record disagree. A staff member says the label was probably swapped during recent works. The driver keeps the transfer on hold until the correct tank, route and safe capacity are independently resolved through the approved arrangement.
02 · Explain the principle
Correct delivery begins with agreement between the ordered product, the vehicle compartment and the identified receiving tank. Use the required documents, compartment identification and site markings, checking that they describe the same transfer. A single readable label is helpful but does not resolve a conflicting record. Wrong-grade delivery can contaminate stock, create unsuitable use and lead to costly or hazardous recovery, even if no liquid escapes.
03 · Carry it into work
A small wrong delivery is still a wrong delivery. Independent agreement and a correct receiving route are prerequisites, not matters to investigate after opening the transfer.
Lesson 3
Protect the public and the entire hose route
Identify changing access, hose and communication risks during delivery.
Control the space around the transfer
Delivery protection must cover more than the tanker parking position. At a forecourt, vehicles and pedestrians may enter from several directions, and customers may not understand a barrier or unusual vehicle movement. The site and driver arrangements should control the actual delivery area, emergency access and interaction with normal trading. A customer stepping into the transfer zone is a changed condition that needs the defined protective response.
A hose is a temporary product pathway exposed to movement, loading and damage. Inspect and use the correct equipment under the approved method, with suitable connections and support. Plan its route to avoid vehicle contact, sharp edges, crushing, excessive strain and trip hazards. Do not extend reach through an improvised coupling, drag across an uncontrolled public route or accept a damaged hose because the remaining delivery is short.
Private properties can make the route less visible and more variable. A hose may pass behind a wall, cross a footpath or lie where a gate or vehicle can trap it. Consider whether the transfer can be observed and controlled as required, and how the driver can communicate and stop safely. A resident offering to watch the hose is not a substitute for the operator’s assessed arrangement or the driver’s required competence.
Keep the route under control throughout transfer and disconnection. Weather, lighting, new vehicle movements and customer actions can alter the initial assessment. If conditions become unsafe, follow the stop procedure before trying to correct them. Maintain the agreed exclusion and emergency access until the transfer equipment has been made safe and removed. A completed meter quantity does not mean that residual liquid, pressure and hose hazards have ended.
How should transport risk be assessed?
Assessment should map people, vehicles, routes, movements, loading, reversing, visibility and work pressure.
A transport assessment should start with a movement map. Where do vehicles enter, reverse, park, load, tip, refuel, charge, turn, couple, uncouple and exit? Where do pedestrians walk, wait, cross, work, queue or visit welfare? Where do temporary works, waste skips, deliveries or contractors change the route?
The assessment should then challenge each interface. Can pedestrians and vehicles be separated? Can reversing be eliminated? Can route direction be simplified? Are visiting drivers briefed? Are banksmen competent and protected? Are schedules realistic enough to prevent rushing?
Risk area
Assessment question
Control focus
Pedestrian routes
Can people walk without entering vehicle routes?
Segregation, barriers and crossings.
Reversing
Can reversing be eliminated or controlled?
One-way routes, turning areas, aids and banksman rules.
Loading/unloading
Who controls the vehicle, load, people and exclusion zone?
Loading plan and communication.
Blind spots
What can the driver not see?
Vehicle selection, aids, exclusion and pedestrian control.
Temporary change
How do works, skips or congestion alter routes?
Change briefing and temporary traffic plan.
Road journeys
Are time, weather, rest and welfare realistic?
Safe journey planning.
How should a busy warehouse yard be controlled?
A strong yard plan separates people and vehicles, controls reversing and manages visiting drivers before they enter the risk area.
A warehouse has vans, articulated lorries, pedestrian staff, agency workers, forklift trucks, visitors and waste collections. Near misses occur when visiting drivers walk across the yard to reception and forklifts reverse near a loading bay. A weak response is to add more warning signs. A stronger response redesigns pedestrian access, creates a driver waiting point, sets a one-way vehicle system, marks loading exclusion zones, controls reversing, briefs visiting drivers, improves lighting, reviews delivery scheduling and checks compliance during peak periods.
The lesson is that transport safety is mainly design and management. Behaviour matters, but only after the site has made the safe route obvious and practical.
Drivers walking through yard. Weak control: Tell them to watch for vehicles; Better control: Create protected pedestrian route and waiting point.
Forklift reversing. Weak control: Rely on reversing alarm; Better control: Redesign route and use exclusion controls.
Loading bay interface. Weak control: Paint lines only; Better control: Physical controls, bay rules and communication.
Fictional loading sequence: prevent early departure
A visiting driver parks as directed and uses the segregated waiting area. The agreed loading controller verifies suitable vehicle/trailer parking brakes and stability, the loading exclusion and the assessed site method that prevents premature departure. Driver and loader confirm the hold is active before work. If that hold, stability or separation is uncertain, loading stops. Only the agreed controller gives positive departure release after people and equipment are clear, the load is safe and all checks are complete. A briefing or painted bay line alone cannot prevent a runaway or drive-away; select the method for the actual vehicles and site.
Applied case
During a heating-oil delivery, a resident opens a vehicle gate that would pinch the hose. The driver stops using the prescribed control, maintains a safe area and resolves the hose route. They do not pull the live hose clear or ask a child to hold the gate.
Decision and explanation
Use the prescribed safe stop and restore an assessed protected route before authorised resumption.
The changing condition threatens containment. Stop within the approved method, then correct and verify the route; moving or straining a live hose can worsen the hazard.
Look closer
Teaching graphic from the linked SHAREhub source section.01 · Read the situation
During a heating-oil delivery, a resident opens a vehicle gate that would pinch the hose. The driver stops using the prescribed control, maintains a safe area and resolves the hose route. They do not pull the live hose clear or ask a child to hold the gate.
02 · Explain the principle
Delivery protection must cover more than the tanker parking position. At a forecourt, vehicles and pedestrians may enter from several directions, and customers may not understand a barrier or unusual vehicle movement. The site and driver arrangements should control the actual delivery area, emergency access and interaction with normal trading. A customer stepping into the transfer zone is a changed condition that needs the defined protective response.
03 · Carry it into work
The changing condition threatens containment. Stop within the approved method, then correct and verify the route; moving or straining a live hose can worsen the hazard.
Lesson 4
Make stopping and escalation part of a successful delivery
Distinguish a justified hold from an improvised workaround.
Completion includes the safe handover
A successful delivery includes the decision not to proceed when the prerequisites fail. Typical hold points include uncertain tank identity, unreliable capacity information, unsuitable access, damaged connections, a suspected tank defect or unavailable emergency arrangements. Use the actual operator’s stop criteria. Explain the specific evidence gap to the customer and control point so that the next action resolves the problem rather than simply applying pressure to the same unsafe task.
If a leak or abnormal condition appears during transfer, follow the authorised stop and emergency procedure. Act from a safe position, alert affected people and provide a clear report. Do not tighten a live leaking coupling, open an unknown valve or use water to wash fuel away. Intervention must remain within training, equipment and the assessed response. Protecting a delivery schedule or customer relationship cannot justify exposure to an uncontrolled release.
After a safe stop, establish what must be checked before resumption. This may require competent assessment of the receiving tank, corrected identification, verified capacity, replacement equipment or a different access plan. Record the actual condition and any residual risks accurately. A verbal assurance that a problem is probably harmless is not equivalent to evidence that the relevant prerequisite is restored.
Normal completion also needs controlled disconnection, checks and handover under the procedure. Confirm what was delivered, report defects or discrepancies, leave the location safe and provide the required records. Those records support stock control, investigation and future delivery planning; they should not hide a spill as a customer-service issue. Environmental notification and specialist recovery remain necessary where the event or threatened pathway requires them.
What should happen when the delivery note and receiver identity disagree?
A discrepancy in product, receiver or available capacity is a hold point before flow. A familiar bay, compatible-looking coupling or verbal assurance cannot settle a conflicting identity. Establish the intended material, destination and route with the people authorised to verify them. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
In an illustrative flammable-liquid delivery, the driver’s paperwork names Tank A while the current site schedule says Tank B. A connection nearby carries an old label. The operator holds connection/start and the supervisor secures the affected bay. They reconcile the delivery, tank identity, pipe route and operating state with competent site information; no small test quantity is transferred to discover the destination. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
The competent operating team verifies capacity using reliable current stock/level information and the planned delivered quantity, with the system’s required allowance. It checks that the intended overfill and shutdown barriers are available, suitable and supported by the specified functional evidence. This page supplies no universal percentage fill limit or permission to bypass an unreliable gauge or protection device. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
Before restart, the site and driver confirm the resolved receiver/product, compatible hose/coupling, applicable bonding/earthing and ignition controls, prevention of vehicle movement, monitoring and the emergency stop route. The technical details must follow the actual system and assessed procedure. HSG176 concerns flammable-liquid tank storage; it is not a universal procedure for every chemical, gas or marine/rail transfer. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
If the discrepancy cannot be resolved, keep the delivery held and communicate the safe waiting or rescheduling decision. Hand-back records the actual transfer state, disconnected/secured interfaces within the site method, remaining restrictions and corrected identification. The manager investigates why obsolete information reached the bay and verifies that the next shift and haulier receive the corrected instruction. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
A private tank has a fresh stain and its condition cannot be confirmed. The customer offers to sign a disclaimer and asks for only half the load. The driver holds delivery, explains the observed defect and seeks the operator’s authorised assessment. The request and reason are recorded without implying that a signature has made the tank safe.
Decision and explanation
No; the receiving arrangement must satisfy the operator’s verified safety criteria.
A signature or reduced quantity does not repair a tank, establish safe capacity or remove the operator’s duties. The evidence gap must be resolved.
Look closer
Photorealistic illustrative UK workplace scene. Review checks: Find: Pedestrians and vehicles would share the proposed unloading area. Hold: Keep the load secured while host and driver agree a protected arrangement. Release: Use the planned unloading method and restore access after hand-back.01 · Read the situation
A private tank has a fresh stain and its condition cannot be confirmed. The customer offers to sign a disclaimer and asks for only half the load. The driver holds delivery, explains the observed defect and seeks the operator’s authorised assessment. The request and reason are recorded without implying that a signature has made the tank safe.
02 · Explain the principle
A successful delivery includes the decision not to proceed when the prerequisites fail. Typical hold points include uncertain tank identity, unreliable capacity information, unsuitable access, damaged connections, a suspected tank defect or unavailable emergency arrangements. Use the actual operator’s stop criteria. Explain the specific evidence gap to the customer and control point so that the next action resolves the problem rather than simply applying pressure to the same unsafe task.
03 · Carry it into work
A signature or reduced quantity does not repair a tank, establish safe capacity or remove the operator’s duties. The evidence gap must be resolved.
Lesson 5
Forecourt receipt: reconcile the whole product-to-tank path
At every transfer boundary, positively establish product, route and receiving capacity before introducing flow.
Understand this fuel-industry task
The separate forecourt illustrates fuel after it has left the terminal. A delivery note, tanker compartment, receiving connection and underground tank all need a consistent identity. A familiar fill-point position or matching hose coupling is not a product check. Wrong-grade delivery can contaminate stock and affect customers; the connection error may also send liquid towards a tank without adequate available capacity. An estimate based only on the usual order size cannot establish safe receiving space.
Use an agreed delivery system that brings the supplier, driver and site receiving information together before unloading. Verify actual product and destination, usable capacity, equipment condition, the assessed transfer route and relevant protective arrangements. Petrol introduces significant vapour and ignition considerations, with site-specific vapour-return arrangements where applicable; do not copy controls blindly between petrol, diesel, heating oil and other products. The competent person must resolve disagreement in records or identification before release. The walkthrough does not authorise learners to connect a hose or manipulate fill points. Its purpose is to practise holding the decision at the correct point and asking for positive evidence, including controlled completion and confirmation that the destination received the intended product.
Trace the initiating event and loss of control
Step
Case pathway
initiatingEvent
Delivery documents, compartment identity or forecourt fill-point information disagree before unloading.
lossOfControl
Transfer begins into an unverified destination or a tank without established safe available capacity.
consequences
Wrong product, overfill, vapour release or spill can affect workers, customers, vehicles and the receiving environment.
Choose effective safeguards
Control priority
Practical application
Eliminate
Avoid a delivery that cannot be completed safely.
Substitute
Use an alternative delivery arrangement or safer access where suitable.
Engineer
Provide suitable fill equipment, containment, impact protection and assessed overfill safeguards.
Manage
Coordinate responsibilities and verify product, tank, capacity and site conditions.
Protect
Use delivery-task PPE for remaining exposure and spill work within competence.
Hold unloading whenever product, compartment, fill point, tank identity or available receiving capacity is uncertain or inconsistent.
Use the agreed competent verification process to reconcile documents with actual equipment and current receiving information.
Confirm the product-specific transfer, vapour, ignition, movement and emergency controls required for this forecourt and delivery.
Supervise transfer through the approved method, stop for abnormal indications and complete controlled isolation, disconnection and receipt records.
Verify effectiveness before release
Ask the driver and receiving representative to trace the same intended product-to-tank path using current information, not memory alone.
Check the basis for available capacity and required protective status and how an unexplained discrepancy is escalated before flow.
Review a safe wrong-identity exercise and subsequent completion evidence: can the team hold the job, resolve it and confirm the correct receipt?
Transfer the decision to the workplace
The same reasoning applies at pipeline receipt and the terminal manifold, but each location has different equipment, protective systems and accountable interfaces.
What should happen when the delivery note and receiver identity disagree?
A discrepancy in product, receiver or available capacity is a hold point before flow. A familiar bay, compatible-looking coupling or verbal assurance cannot settle a conflicting identity. Establish the intended material, destination and route with the people authorised to verify them. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
In an illustrative flammable-liquid delivery, the driver’s paperwork names Tank A while the current site schedule says Tank B. A connection nearby carries an old label. The operator holds connection/start and the supervisor secures the affected bay. They reconcile the delivery, tank identity, pipe route and operating state with competent site information; no small test quantity is transferred to discover the destination. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
The competent operating team verifies capacity using reliable current stock/level information and the planned delivered quantity, with the system’s required allowance. It checks that the intended overfill and shutdown barriers are available, suitable and supported by the specified functional evidence. This page supplies no universal percentage fill limit or permission to bypass an unreliable gauge or protection device. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
Before restart, the site and driver confirm the resolved receiver/product, compatible hose/coupling, applicable bonding/earthing and ignition controls, prevention of vehicle movement, monitoring and the emergency stop route. The technical details must follow the actual system and assessed procedure. HSG176 concerns flammable-liquid tank storage; it is not a universal procedure for every chemical, gas or marine/rail transfer. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
If the discrepancy cannot be resolved, keep the delivery held and communicate the safe waiting or rescheduling decision. Hand-back records the actual transfer state, disconnected/secured interfaces within the site method, remaining restrictions and corrected identification. The manager investigates why obsolete information reached the bay and verifies that the next shift and haulier receive the corrected instruction. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
The note specifies petrol, but the nominated fill-point identity disagrees with the driver’s compartment record. A colleague says the same vehicle delivers here every week.
Decision and explanation
A competent positive reconciliation of the product, compartment, actual fill point, receiving tank and safe capacity.
Correct. Familiarity is not evidence that this delivery, connection and destination agree; resolve the complete route before authorising unloading. That uses an unverified transfer as a test and can contaminate or overfill the wrong tank before the mistake is recognised. Order history does not establish current capacity or correct product identity. The receiving system and current evidence must agree.
Look closer
Photorealistic illustrative UK workplace scene. Review checks: Vehicle: Unplanned movement can trap or strike people at the loading area. Load: An unstable or unsecured load can shift, fall or overturn equipment. Transfer: A failed connection or incompatible product can create a separate substance exposure.01 · What to notice
The separate petrol-station scene has controlled fill points. The exercise delivery note, connection identity and available receiving capacity have not been positively reconciled.
02 · Trace the harm
Wrong-grade or wrong-tank delivery can contaminate customer fuel, overfill storage and create a flammable release where the public may be present.
03 · Test the safeguard
Trace the actual connection against reliable tank and product identification and capacity evidence; verify protection, exclusion and communication before authorising unloading.
Lesson 6
Forecourt unloading: protect the public around a temporary process
A delivery creates a temporary process boundary; public protection must work for people unfamiliar with the task.
Understand this fuel-industry task
The delivery tanker temporarily extends the forecourt's fuel system into an area also used by customers, vehicles and pedestrians. Hoses, couplings and unloading activities introduce trip, impact, drive-away and release risks at the same time that people are arriving to buy fuel or visit the shop. A customer following a familiar walkway may not recognise the temporary work zone. Reflective clothing and a traffic cone are useful only within an arrangement that actually controls access and movement.
Plan the vehicle position and protected working area with the receiving site so public routes and emergency access remain suitable. Where a route cannot be kept safe during unloading, change the arrangement or suspend the conflicting activity before transfer begins. The need is reliable separation and communication, not a universal claim that every forecourt must operate identically. Consider sight lines, reversing, mobility needs, children and people approaching from the shop as well as arriving cars. Keep the driver able to monitor the transfer and stop through the approved method. Asking the driver to direct customers while attending critical controls can divide attention and weaken both tasks. Reassess if barriers move, a queue changes or an emergency route becomes obstructed.
Trace the initiating event and loss of control
Step
Case pathway
initiatingEvent
Customers and vehicles are allowed through the tanker work zone during a petrol delivery.
lossOfControl
A person or vehicle enters the temporary transfer boundary, damages equipment or distracts the person controlling unloading.
consequences
Striking, crushing, trips, fuel release and ignition can affect people who have no delivery training or protective role.
Choose effective safeguards
Control priority
Practical application
Eliminate
Avoid a delivery that cannot be completed safely.
Substitute
Use an alternative delivery arrangement or safer access where suitable.
Engineer
Provide suitable fill equipment, containment, impact protection and assessed overfill safeguards.
Manage
Coordinate responsibilities and verify product, tank, capacity and site conditions.
Protect
Use delivery-task PPE for remaining exposure and spill work within competence.
Agree a suitable tanker position and unloading arrangement with the receiving site, protecting public routes and responder access.
Physically control the assessed temporary work zone and conflicting traffic or customer activities before release of the delivery.
Provide clear understandable directions and suitable assistance or alternative access without dividing the transfer operator’s critical attention.
Maintain movement prevention, monitoring and emergency stop arrangements; pause unloading when the protected setup is defeated or conditions change.
Verify effectiveness before release
Walk the approach from the road, pumps and shop: can a customer inadvertently enter the work zone or be directed into moving traffic?
Observe a safe setup exercise and check barrier stability, access for people needing assistance and the separation of traffic-management and transfer roles.
Inject a displaced barrier or blocked exit in a tabletop drill; verify who stops unloading and how a safe arrangement is restored.
Transfer the decision to the workplace
Use this approach at busy terminal gates, workshops and customer drives: plan movement and transfer together and stop when the separation cannot be maintained.
What barriers should be healthy before transfer starts?
A transfer starts only when the product, route, connection, receiver and stop system are independently confirmed.
HSE HSG176 gives specific guidance for flammable liquid tank transfer, including earthing, overfill protection and preventing movement while connected. HSE loading guidance applies to vehicle stability, exclusion and safe load movement. Select the barriers for the product and facility; marine, gas and general pallet handling may require different controls.
At a road-tanker bay, one person verifies the delivery note against tank identity and capacity, another confirms line-up as the method requires, and the operator tests the emergency stop path. Any leak, unexpected level trend, lost earth connection or driver movement attempt stops transfer and triggers the site response.
During setup, a public route to the shop passes between the tanker and its unloading connections. The driver proposes watching pedestrians while also controlling the delivery.
Decision and explanation
An agreed protected work zone and suitable public route or activity restriction that lets unloading be monitored properly.
A sign does not remove the conflict or divided attention. Public movement and critical transfer monitoring need an arrangement that works together. Speeding the task cannot establish segregation and may add operating risk. Resolve the work-zone conflict before transfer. Correct. Prevent the interaction through the actual layout and roles, then maintain the arrangement throughout the delivery.
Look closer
Photorealistic illustrative UK workplace scene. Review checks: Eliminate: Avoid unnecessary transfer or redesign to a closed fixed connection. Reduce: Use a less hazardous compatible product or smaller batch where possible. Isolate: Closed hose, correct coupling, earthing/overfill and emergency stop. Control: Product/route cross-check, driver coordination, exclusion and supervised line-up. PPE: Product-compatible gloves, eye and other residual splash protection.01 · What to notice
The forecourt case proposes keeping a public walkway and vehicle route through the tanker work zone during unloading.
02 · Trace the harm
Customers can strike transfer equipment, enter a release area or bring ignition into the operation; the public will not share the driver’s task knowledge.
03 · Test the safeguard
Inspect the actual forecourt during a safe delivery walk-through: people and vehicles remain separated from the task and emergency controls and exits stay available.
Lesson 7
Heating-oil receipt: a small customer site still needs a sound system
Product and scale change the arrangements, not the need for verified identity, capacity and a suitable receiving system.
Understand this fuel-industry task
The private-customer scene represents heating oil, not petrol unloading at a forecourt. Product properties and receiving arrangements differ, so a petrol delivery checklist cannot simply be copied across. Nevertheless, identity, condition, capacity and safe access remain essential questions. A damaged tank, poor support, unclear remote fill connection or unreliable capacity information can turn a routine top-up into a substantial spill beside buildings, soil or drains. Long service history does not show that the receiving system is sound today.
Before release, use the supplier's competent delivery procedure to establish the intended tank and product, acceptable receiving condition and safe available capacity. A customer's usual order or statement that the tank is empty is information to examine, not proof of the full system. Resolve uncertainty through the agreed assessment and escalation route, including a refusal or delay where the delivery cannot be made safely. Oil-storage requirements depend on use, location and jurisdiction; domestic and business cases can have different rules and assessment needs. Inspection history, tank labelling and maintenance support the decision but do not authorise filling over a current defect. Include the hose route, delivery visibility, communication and safe stop so an otherwise sound tank is not undermined by the temporary setup.
Trace the initiating event and loss of control
Step
Case pathway
initiatingEvent
A heating-oil delivery is accepted without confirmed tank identity, safe capacity or satisfactory current receiving condition.
lossOfControl
Oil enters the wrong system, exceeds available space or escapes from a defective tank, pipe or connection.
consequences
Soil, drains and nearby property can be contaminated, with exposure, fire and expensive recovery consequences.
Choose effective safeguards
Control priority
Practical application
Eliminate
Avoid a delivery that cannot be completed safely.
Substitute
Use an alternative delivery arrangement or safer access where suitable.
Engineer
Provide suitable fill equipment, containment, impact protection and assessed overfill safeguards.
Manage
Coordinate responsibilities and verify product, tank, capacity and site conditions.
Protect
Use delivery-task PPE for remaining exposure and spill work within competence.
Hold delivery when tank or product identity, available capacity, condition or safe access is uncertain; use the supplier’s competent escalation route.
Assess the actual receiving tank, support, connection and relevant pipework through the appropriate delivery and inspection arrangements.
Apply the relevant domestic or business oil-storage requirements for the actual nation and site rather than assuming a universal exemption or design rule.
Confirm a controlled temporary delivery setup, monitoring, communication and safe-stop method and record defects for customer resolution.
Verify effectiveness before release
Trace the intended fill point to the actual tank and verify the reliable basis for available receiving space for this order.
Compare current condition and relevant inspection or defect information with the supplier’s acceptance criteria; investigate unexplained stains or damage.
Check how the driver records and escalates a refused delivery and how the customer demonstrates defects are resolved before a later visit.
Transfer the decision to the workplace
Carry this evidence-based refusal principle into all customer deliveries: explain the unresolved condition and the route to a safe future delivery rather than improvising a smaller fill.
What evidence should be available for transfer operations?
Evidence should prove the transfer system is safe today, not just that a procedure exists.
Assurance follows one actual transfer: product and tank identity, vehicle immobilisation, hose test, barrier functional check, start authorisation, level trend, stop event and hand-back. Sample records and observe the bay; a signed form alone does not prove the connection was right.
Evidence
What it should show
Failure to challenge
Transfer procedure
Correct sequence for line-up, transfer, monitoring, abnormal response and handback.
Procedure differs from field equipment.
Barrier register
Critical safeguards, owners, tests, impairments and performance standards.
No owner for overfill or ESD protection.
Hose/coupling register
Compatibility, inspection, testing, service life and defect control.
Hoses stored badly or used beyond inspection date.
dangerous-substances fire/explosion assessment
Explosive atmosphere formation, ignition control and emergency mitigation.
Area classification not matched to actual transfer conditions.
Training and authorisation
Operators, drivers, supervisors and contractors know critical steps.
Generic induction with no transfer-specific assessment.
Incident and weak-signal review
Leaks, drips, alarms, near misses and aborted transfers are trended.
Small leaks normalised as housekeeping problems.
Applied case
The customer requests the usual quantity. The tank gauge is unreliable and a new stain is visible beneath a support, but the customer says previous deliveries were fine.
Decision and explanation
Hold the delivery and obtain the competent tank-condition and capacity assessment through the supplier’s process.
An arbitrary reduction does not establish capacity or integrity. A defective tank can release even a small delivery. Correct. Resolve the current uncertainties before authorising receipt, with clear information for the customer and a controlled follow-up. Past success does not establish current condition. Heating oil can pollute through a damaged system even at a domestic property.
Look closer
Photorealistic illustrative UK workplace scene. Review checks: Find: Pedestrians and vehicles would share the proposed unloading area. Hold: Keep the load secured while host and driver agree a protected arrangement. Release: Use the planned unloading method and restore access after hand-back.01 · What to notice
The private-customer scene is heating oil, not a petrol forecourt. The exercise request lacks confirmed tank identity, available capacity and an acceptable receiving condition.
02 · Trace the harm
Overfill, a failed tank or unsuitable connection can release oil onto land, into drains or towards nearby buildings, even at a domestic property.
03 · Test the safeguard
Confirm the actual receiving system and assessed capacity, safe route and connection, and required documentation; resolve defects before an authorised delivery proceeds.
Lesson 8
Customer hose routes: control the whole temporary connection
Follow the whole hose and the people around it; safe tank capacity alone cannot make an uncontrolled delivery route acceptable.
Understand this fuel-industry task
The long hose links a road tanker with a private heating-oil tank beyond a pavement and garden entrance. The hazard is distributed along the whole route, not only at the fill point. Pedestrians may trip, a car can crush the hose and a moving vehicle can strain a connection. Damage or a poorly monitored leak can release oil into drains or neighbouring ground while the driver is focused elsewhere. Children, deliveries and other visitors can change the setup after it initially looks quiet.
The delivery assessment needs a suitable vehicle position, maintained equipment, a controlled route, visibility, communication and a safe way to stop. Public-route protection must follow the approved arrangement and any relevant authority requirements; the driver cannot assume that customer permission controls a public pavement. A hose ramp or cone is only useful if suitable for the actual movement and maintained in position within a complete plan. Do not transfer a safety-critical monitoring role to an unbriefed customer simply because the route is long. Where the route cannot be made suitable, revise or postpone the delivery through the supplier's process. Inspect changing conditions throughout and include controlled draining, disconnection and removal so the route does not become hazardous at the end.
Trace the initiating event and loss of control
Step
Case pathway
initiatingEvent
A delivery hose is laid across a public route and vehicle entrance without a suitable protected setup.
lossOfControl
A pedestrian encounters the obstruction or a vehicle damages or moves the hose while transfer continues.
consequences
Trips, falls, hose or connection failure and an oil release can harm the public and contaminate drains or neighbouring property.
Choose effective safeguards
Control priority
Practical application
Eliminate
Avoid a delivery that cannot be completed safely.
Substitute
Use an alternative delivery arrangement or safer access where suitable.
Engineer
Provide suitable fill equipment, containment, impact protection and assessed overfill safeguards.
Manage
Coordinate responsibilities and verify product, tank, capacity and site conditions.
Protect
Use delivery-task PPE for remaining exposure and spill work within competence.
Assess and walk the complete route before release, including public access, vehicle crossings, changing occupancy and the safe tanker position.
Use suitable maintained hoses, couplings and approved route protection with any required permissions or movement arrangements for the location.
Provide effective transfer monitoring and communication with a usable stop method; do not rely on an untrained customer as the control system.
Pause if the protected route or visibility fails and complete controlled disconnection and removal before returning the route to normal use.
Verify effectiveness before release
Trace every metre between vehicle and tank and view crossings from a pedestrian, mobility-aid user and vehicle-driver perspective.
Check equipment suitability and condition and demonstrate the approved monitoring and stop arrangement safely from the actual working positions.
Test how the team handles a car wanting access or a displaced protective device, including who pauses the task and how safe access is restored.
Transfer the decision to the workplace
Apply this complete-route review to temporary pipework, cables and mobile transfer systems, where unseen sections and changing public movements can defeat the initial setup.
How should a traffic management plan be built?
Build a site-specific plan from observed routes, vehicle envelopes, people, activities, controls, owners and change triggers; check it in the field before movement.
Sketch arrival, parking, unloading, pedestrian desire lines, crossings, welfare, work zones and emergency access. Test the largest intended vehicle and load, including turning, swept path, clearance, visibility and surface. Use a competent designer where geometry or public interface is complex; no universal site speed or barrier specification is supplied here.
Agree who owns gates, bookings, barriers, driver briefings, vehicle checks, temporary changes and inspection. Keep the plan where users can act on it. Stop and revise when the real route differs from the drawing.
Plan element
Questions to answer
Typical evidence
Movement and people
Who arrives, walks, cycles, loads, reverses or may cross?
Observed movement map and consultation.
Layout and plant
Can the intended vehicle, load and people move with separation and clearance?
Competent layout and vehicle check.
Operating controls
Who controls booking, gate, crossing, speed, unloading and emergencies?
Named owners and communicated rules.
Change and assurance
What triggers a hold, revision and authorised restart?
Field check, defect record and hand-back.
Road boundary
Could works affect a public road, footway, cycleway or sightline?
Authority consultation and approved competent scheme where required.
Applied case
The driver cannot see both the fill point and a hose crossing at the customer’s driveway. The customer offers to watch the pavement while answering the door.
Decision and explanation
Establish the approved protected hose route, reliable monitoring and communication; revise or delay if it cannot be kept safe.
Correct. The complete temporary connection must be controlled, including the public interface and a workable safe stop. Availability does not establish competence, attention or clear communication. An unbriefed customer is not a reliable safety-critical control. That leaves an obstruction and exposure to vehicle damage, and may exclude people who cannot safely cross the hose.
Look closer
Photorealistic illustrative UK workplace scene. Review checks: Failed separation: A blocked or displaced barrier puts people into the vehicle or load path. Possible consequence: Collision, crushing, trapping or injury from a moving load can follow. Warning signs and action: Damaged barriers, poor sightlines, soft ground, unbriefed deliveries or an unprotected shortcut require affected movements to be held and reviewed.01 · What to notice
The private delivery case proposes a long hose across a pavement and garden entrance without adequate control of the public, vehicles or hose condition.
02 · Trace the harm
A person can trip, a vehicle can damage the hose and a release can reach drains or neighbouring property; remote delivery visibility and communication also matter.
03 · Test the safeguard
Walk the whole route and confirm equipment condition, protected crossings, safe vehicle position, communication and emergency stop can work for the actual task.
Lesson 9
Two destinations, two delivery decisions
Apply common principles while preserving the different delivery methods.
Bring the evidence together
A tanker leaving Crown Fuels may deliver petrol to a public forecourt or heating oil to a private customer. These settings share the need for correct product, a sound receiving system, sufficient safe capacity and controlled transfer, but their equipment and procedures are not interchangeable. This course uses both model destinations to practise pre-delivery checks, customer/public interfaces, hose protection and safe stop decisions. It supports awareness alongside the operator’s procedures and required driver training; completion is not ADR certification, a tank inspection qualification or authorisation to unload.
Consider the whole sequence of interfaces and degraded conditions. A local repair or completed permit cannot by itself show that every required barrier is available. Separate immediate protection, the competent technical resolution, the operating decision and independent verification.
Use the worked cases and the linked primary guidance to identify the missing information. State who owns the decision and what would keep the operation restricted. The fictional scene illustrates choices; it cannot establish actual process limits, emergency capability or permission to operate.
What should happen when the delivery note and receiver identity disagree?
A discrepancy in product, receiver or available capacity is a hold point before flow. A familiar bay, compatible-looking coupling or verbal assurance cannot settle a conflicting identity. Establish the intended material, destination and route with the people authorised to verify them. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
In an illustrative flammable-liquid delivery, the driver’s paperwork names Tank A while the current site schedule says Tank B. A connection nearby carries an old label. The operator holds connection/start and the supervisor secures the affected bay. They reconcile the delivery, tank identity, pipe route and operating state with competent site information; no small test quantity is transferred to discover the destination. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
The competent operating team verifies capacity using reliable current stock/level information and the planned delivered quantity, with the system’s required allowance. It checks that the intended overfill and shutdown barriers are available, suitable and supported by the specified functional evidence. This page supplies no universal percentage fill limit or permission to bypass an unreliable gauge or protection device. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
Before restart, the site and driver confirm the resolved receiver/product, compatible hose/coupling, applicable bonding/earthing and ignition controls, prevention of vehicle movement, monitoring and the emergency stop route. The technical details must follow the actual system and assessed procedure. HSG176 concerns flammable-liquid tank storage; it is not a universal procedure for every chemical, gas or marine/rail transfer. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
If the discrepancy cannot be resolved, keep the delivery held and communicate the safe waiting or rescheduling decision. Hand-back records the actual transfer state, disconnected/secured interfaces within the site method, remaining restrictions and corrected identification. The manager investigates why obsolete information reached the bay and verifies that the next shift and haulier receive the corrected instruction. Related guidance: Storage of flammable liquids in tanks (HSG176, 2nd edition, 2015).
At the morning petrol forecourt, recent works have left two fill labels inconsistent with the stock record and customers are crossing the unloading area. At the afternoon heating-oil address, the tank has an uncertain support condition and the proposed hose crosses an uncontrolled path. The planner asks the driver to complete both jobs because the vehicle is late. Compare the product and receiver arrangements, identify each stop trigger, state what evidence and people are needed to resolve it, and plan the safe record and handover for any refused or resumed delivery.
Decision and explanation
Hold each unsafe delivery and resolve its specific identification, capacity, condition and route controls through the appropriate procedure.
The two settings share verification principles but require distinct procedures and controls. Neither a small transfer nor a customer signature resolves the stated defects.
Look closer
Photorealistic illustrative UK workplace scene. Review checks: Eliminate: Avoid unnecessary transfer or redesign to a closed fixed connection. Reduce: Use a less hazardous compatible product or smaller batch where possible. Isolate: Closed hose, correct coupling, earthing/overfill and emergency stop. Control: Product/route cross-check, driver coordination, exclusion and supervised line-up. PPE: Product-compatible gloves, eye and other residual splash protection.01 · Read the situation
At the morning petrol forecourt, recent works have left two fill labels inconsistent with the stock record and customers are crossing the unloading area. At the afternoon heating-oil address, the tank has an uncertain support condition and the proposed hose crosses an uncontrolled path. The planner asks the driver to complete both jobs because the vehicle is late. Compare the product and receiver arrangements, identify each stop trigger, state what evidence and people are needed to resolve it, and plan the safe record and handover for any refused or resumed delivery.
02 · Explain the principle
A tanker leaving Crown Fuels may deliver petrol to a public forecourt or heating oil to a private customer. These settings share the need for correct product, a sound receiving system, sufficient safe capacity and controlled transfer, but their equipment and procedures are not interchangeable. This course uses both model destinations to practise pre-delivery checks, customer/public interfaces, hose protection and safe stop decisions. It supports awareness alongside the operator’s procedures and required driver training; completion is not ADR certification, a tank inspection qualification or authorisation to unload.
03 · Carry it into work
The two settings share verification principles but require distinct procedures and controls. Neither a small transfer nor a customer signature resolves the stated defects.
Lesson 10
Turn the learning into a verified workplace action
Choose a bounded action, owner, task-specific evidence and escalation trigger within your role.
Make the course useful at work
Separate retail petrol-forecourt and private heating-oil cases; product, legal duties and receiving arrangements are deliberately compared, never treated as interchangeable.
Choose one relevant task from this course. Describe the material, equipment, people and interfaces, then explain the credible harm pathway before choosing the control. Follow the actual site process for obtaining missing technical evidence and deciding whether work may proceed.
Use the linked resource with a specific question. A briefing should test understanding; a checklist should identify missing facts; an audit should compare claims with observations. Keep this exercise fictional and separate from live operating records.
Record the planned action, responsible role, verification evidence and a trigger for escalation or reassessment. Completion of this course is a learning record, not an operating instruction, engineering design, specialist licence or authority to enter, isolate or fight a fire.
What evidence shows human factors are controlled in process operations?
Evidence should show that human factors are understood, controlled and checked where they affect major accident barriers.
Good assurance uses all three lines of defence. First-line supervisors observe critical tasks and check whether workers can perform them. Second-line HSE or process safety teams audit themes such as permits, alarms, handover and safety-critical procedures. Third-line technical authorities or external specialists review deeper topics such as alarm philosophy, control-room design, safety-critical task analysis or staffing assumptions. HSE COMAH bulk storage systems
The most useful evidence is specific. 'Training completed' is weaker than a record showing an operator successfully completed a simulated trip recovery using the current procedure and alarm screen.
Your handover action says improve fuel safety but names no operation, control owner, evidence or stopping condition.
Decision and explanation
Name the actual task, competent control owner, evidence required and the hold/escalation trigger.
An effective plan connects a real task and control with a responsible role, objective evidence and a clear decision boundary. A course badge or signature does not establish the plant condition.
Look closer
Photorealistic illustrative UK workplace scene. Review checks: Immediate action: Were valves labelled, segregated, accessible and independently verified? Procedure: Was the critical lineup step visible, current and usable during real transfer work? Alarm system: Was it trusted, prioritised and linked to a clear operator action?01 · Read the situation
Your handover action says improve fuel safety but names no operation, control owner, evidence or stopping condition.
02 · Explain the principle
Separate retail petrol-forecourt and private heating-oil cases; product, legal duties and receiving arrangements are deliberately compared, never treated as interchangeable.
03 · Carry it into work
An effective plan connects a real task and control with a responsible role, objective evidence and a clear decision boundary. A course badge or signature does not establish the plant condition.