Independent SHAREhub process-safety awareness using fictional cases and a Great Britain baseline; check the applicable Northern Ireland duties and actual site arrangements. This course does not award a NEBOSH qualification, establish specialist competence or authorise hazardous work.
This reader supplies the complete teaching. Use the interactive LMS course for assessed activities, saved progress and completion.
LESSON 1
Plan for the scenario rather than a generic evacuation
Plan for the scenario rather than a generic evacuation.
Existing SHAREhub photographic illustration. The written fictional case supplies the condition and decision evidence.
Understand the mechanism and the decision
Emergency preparedness begins with credible events and their consequences for people, the environment and neighbouring activities. A process release, fire, utility loss or other emergency may need different protective actions. A normal building-fire exercise cannot establish readiness for every major-hazard scenario.
Use the actual risk and plant information to define the response basis. Specific COMAH emergency duties depend on applicability, tier and jurisdiction; an ordinary workplace still needs suitable emergency arrangements. Do not infer that a site is in or out of a legal regime from an awareness-course title.
Verify the control in the actual task
Check the actual emergency-planning basis and responsible roles; do not invent a universal evacuation rule or assume every site has identical statutory duties.
Which scenarios should emergency preparedness cover?
Emergency preparedness should cover the major accident scenarios that could challenge people, equipment, emergency services and public protection.
A credible major accident scenario is not a vague hazard label. 'Fire' is too broad; 'bunded tank fire after overfill and vapour ignition with potential off-site smoke impact' is a scenario. 'Gas release' is too broad; 'toxic gas release during unloading with wind towards public receptor' starts to guide decisions.
Scenario selection should include initiating event, escalation route, consequences, early warning, emergency actions, resources, muster/shelter choice, isolation, responder safety, environmental pathways and recovery. The plan should also cover reasonably foreseeable low-probability, high-consequence events.
Major accident scenario prompts - Major accident scenario prompts
Scenario
Planning questions
Evidence
Loss of containment
What leaks, how quickly, where does it go?
Hazard register and isolation plan.
Toxic release
Who shelters, who warns the public, what monitoring is needed?
Toxic plume plan and communications.
Tank fire
What foam/water is needed and what runoff containment exists?
Firewater and containment checks.
Vapour cloud explosion
How are ignition, escalation and casualty zones managed?
DSEAR and emergency plan.
BLEVE or vessel heating
When is withdrawal safer than firefighting?
Pressure vessel fire scenario.
Domino escalation
Which neighbouring plant or businesses may be affected?
Layout and external interface review.
Start with the safety report and hazard studies: a tank overfill, toxic release, multiple tank fire or explosion can damage normal routes, utilities and communications. Decide which scenarios require shelter, evacuation, rescue or source control, including low-probability severe events; record assumptions that exercises must challenge. See HSE COMAH 2015 duties and emergency planning.
Applied case
A site proposes using last year building-fire drill as the only evidence of readiness for a toxic-release scenario.
Test the assumption
Only that the old drill was quick. This does not establish acceptance. Different hazards can require different protection and coordination.
Evidence before acceptance
Check the actual emergency-planning basis and responsible roles; do not invent a universal evacuation rule or assume every site has identical statutory duties.
Test your decision
What must be established?
The scenario-specific protective response, roles and interfaces for the actual release.
Only that the old drill was quick.
That every emergency requires identical movement.
Compare the explanation
The scenario-specific protective response, roles and interfaces for the actual release.
Different hazards can require different protection and coordination.
Know the alarm, role and immediate protective boundary
Fire classes and fire extinguishersFire classes · agent types · dangerous mismatches
Recognise the fuel. Read the extinguisher. Protect your escape.
People and escape first. Raise the alarm, follow the site’s evacuation plan and arrange the emergency call to 999. Only consider a small fire in its earliest stage if you are trained, authorised, have the correct equipment and a clear escape behind you. Smoke, spreading fire, uncertainty or an unsafe approach mean withdraw. Never delay escape to fetch an extinguisher.
UK awareness reference for common and specialist portable extinguisher families. Actual ratings, exclusions and manufacturer instructions govern each unit. Reading this guide is not practical training or permission to fight a fire. Fixed systems, hose reels and specialist industrial firefighting require their own assessed arrangements.
Emergency coordination: the alarm, protective action and assigned role come before equipment selection.
Fire classes: fuel, examples and the important distinction
Class
Fuel and examples
What matters
AClass A
Solid materials
Wood, paper, textiles and many solid plastics.
Usually forms an ember or char bed. Cooling matters; check the marked A rating.
BClass B
Flammable liquids
Petrol, solvents, diesel when burning, and liquefiable solids such as wax.
Fuel can spread across a surface. An unsuitable jet can spread burning liquid; solvent compatibility matters.
CClass C
Flammable gases
Propane, butane or methane.
Not a routine employee firefighting task. Knocking down flame while gas continues to escape can create an explosive cloud. Fuel isolation requires safe, competent action under the emergency plan.
DClass D
Combustible metals
Magnesium, sodium or metallic lithium.
Needs a metal-specific specialist agent. Ordinary ABC powder is not Class D powder.
FClass F
Cooking oils and fats
Hot oil in a fryer or pan.
Very hot oil can reignite. Water can produce violent steam expansion and eject burning oil.
LClass L
Lithium-ion batteries
A lithium-ion tool, e-bike or vehicle battery in thermal runaway.
Class L is included in BS ISO 3941:2026. Toxic or flammable gas, heat propagation and reignition need specialist planning. This is different from a metallic-lithium Class D fire.
Electrical equipment: Energised electrical equipment is an additional hazard, not a UK fire class called E. Do not import US Class C electrical or Class K cooking labels into this UK guide. Isolation, only where safe and authorised, does not remove the burning fuel or stored battery energy. Use the unit’s explicit electrical suitability and limitations.
Class L is the 2026 addition to the classification standard. Existing extinguisher labels and product test claims vary; a new class name does not certify every battery product.
Compare the classes · including lithium-ion batteries
Typical = usual application for the labelled family. If rated / unit limits = confirm the actual label and manufacturer conditions. No = not a normal selection for that hazard; specialist engineered arrangements are separate. This table cannot authorise firefighting.
* Electrical is an additional hazard, not a fire class. Gas-fire and battery-fire response require the assessed specialist plan. Scroll the table sideways on a narrow screen.
Typical portable-agent applications: always confirm the actual unit
Agent family
A · solids
B · liquids
C · gases
D · metals
Electrical*
F · cooking oil
L · Li-ion
Water
Typical
No
No
No
Unit limits
No
No
Water spray / water with additives
Typical
If rated
No
No
Unit limits
No
No
Foam
Typical
Typical
No
No
Unit limits
No
No
Water mist
Typical
If rated
No
No
Unit limits
If rated
Specialist plan
ABC dry powder
Typical
Typical
Specialist plan
No
Unit limits
No
No
BC dry powder
No
Typical
Specialist plan
No
Unit limits
No
No
Class D specialist powder
No
No
No
Exact metal
No
No
No
Carbon dioxide (CO₂)
No
Typical
No
No
Unit limits
No
No
Wet chemical
If rated
If rated
No
No
Unit limits
Typical
No
Clean agent / vaporising liquid
Unit rating
Unit rating
No
No
Unit limits
No
No
Battery-specific suppression products
If rated
No
No
No
Unit limits
No
Specified battery
Extinguisher types: uses and dangers
These are typical applications, not universal permissions. Check the label on the actual unit. Images are photorealistic teaching illustrations inspired by the referenced equipment; they are not photographs or certified product labels. Use Inspect the parts to explore the hardware. Band, nozzle and label details vary.
Common and specialist portable extinguisher families
Type and recognition
Typical rating and use
Wrong use: what can go wrong?
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
WaterRed / WATER marking
Normally A
Cools burning solid material such as paper, wood or fabric.
Check the limitation
Ordinary water is unsuitable for live electrical equipment, flammable-liquid pools, cooking oil and reactive metals: shock, spreading fuel or violent reaction can result.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Water spray / water with additivesUsually red; read the agent name
A; B only if explicitly rated
Improved wetting or spray performance can help on the hazards stated on that model’s label.
Check the limitation
An additive does not make every water extinguisher safe for electricity, oils or reactive chemicals. Check the specific exclusions.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Direct spray nozzle
This compact foam example has a nozzle attached directly to the valve. Larger units may have a hose. Recognise the actual discharge arrangement and use only the approved agent and instructions.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
FoamCream panel / FOAM
Commonly A and B
Cools and forms a surface blanket on suitable liquid fires. The agent must suit the actual fuel; some alcohols need alcohol-resistant foam.
Check the limitation
Ordinary foam is not a general answer for live electricity, cooking oil or metal fires. Unsuitable foam may break down on a solvent; a jet can spread fuel. Free-flowing fuel needs specialist response.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Fine-mist nozzle
The specially designed nozzle creates the intended fine spray. It is not an ordinary water jet. Nozzle appearance alone does not establish any tested electrical suitability.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Water mistManufacturer marking varies
Model-specific; commonly A, some F
Fine droplets absorb heat. Some products have additional ratings or tested electrical suitability, with stated voltage and distance conditions.
Check the limitation
‘Mist’ is not universal approval. Use only the classes and electrical conditions actually declared for that model; do not assume it covers metals, liquids or batteries.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
ABC dry powderBlue panel / ABC POWDER
A, B and C if marked
Interrupts flame chemistry; multipurpose powder also acts on Class A material. A C marking does not authorise tackling a gas leak.
Check the limitation
Powder can obscure escape and impair breathing; it is not generally recommended indoors. Limited cooling allows reignition. It is not metal-specific D powder or a substitute for F-rated cooking-oil equipment.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
BC dry powderBlue panel / BC POWDER
B and C if marked; not A
Selected for particular liquid or gas hazards under the assessed plan. Electrical use must follow the actual unit’s instructions.
Check the limitation
Do not assume all blue powder extinguishers protect wood or paper. It has the visibility, breathing and reignition limitations of powder; it does not provide Class D or F protection.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Specialist low-velocity applicator
The specialist applicator places the compatible metal-fire agent without unnecessarily disturbing burning material. Both agent and application method must suit the specific metal; this is not an ABC powder nozzle.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Class D specialist powderSpecific metal and agent named on label
D, for the specified metal
A specialist powder can isolate or absorb heat from a compatible burning metal. Selection requires knowledge of the metal and its form.
Check the limitation
The wrong powder can fail or react. Water, foam and CO₂ can be dangerous on certain burning metals. A powder suitable for magnesium is not automatically suitable for metallic lithium.
Parts in text
Cylinder
The narrow steel cylinder contains carbon dioxide under pressure. There is normally no pressure gauge on this portable type; service assessment includes the appropriate mass and integrity checks by competent personnel.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Horn and designated insulated grip
The flared horn directs the CO₂ discharge. Discharge parts can become extremely cold. Only the parts identified by the manufacturer as safe to hold should be gripped; not every horn is frost-free.
Displaces the atmosphere around a small flame and leaves no powder residue. Often selected around electrical equipment.
Check the limitation
Poor cooling means reignition is possible. CO₂ can create a dangerous atmosphere in enclosed spaces; discharge can cause frostbite. Hold only the designated insulated parts. Not a cooking-oil or metal-fire substitute.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, lance and spray applicator
The hose feeds the long lance and purpose-designed applicator. It helps distinguish this kitchen-fire unit from an ordinary short-nozzle extinguisher. Use requires model-specific practical training.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Wet chemicalYellow panel / WET CHEMICAL
F; often A if marked
Cools cooking oil and creates a protective surface layer through reaction with the fat. Use only within the actual unit’s rating and instructions.
Check the limitation
Do not mistake it for a general liquid-fire or electrical extinguisher. Incorrect application or moving the fryer can splash hot oil; apparent flame-out does not establish safe temperature.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Clean agent / vaporising liquidRead the agent; no universal colour shortcut
Product- and jurisdiction-specific
Specialist low-residue agents may protect sensitive equipment. Confirm the UK-approved application and the manufacturer’s limits.
Check the limitation
Low residue does not mean safe to breathe. Do not copy a US A:B:C rating as UK gas-fire approval. Legacy halon is restricted to permitted critical uses and applicable deadlines.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
This generic illustration has a green agent area and boot inspired by the supplied product. Green is not a universal Class L identification code. Read the real product name, chemistry, battery limits and instructions.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, grip and applicator
The illustrated hose has a coloured ribbed grip and a small application tip. This shows the hardware family, not a tested battery capability. Follow the instructions for the actual agent and generation.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Battery-specific suppression productsNamed formulation and tested application
Check independent scope and instructions
Some products use water-based cooling or specialist media such as aqueous vermiculite for specified battery scenarios. Selection depends on chemistry, capacity and location.
Check the limitation
A ‘lithium’ label is not proof it will stop thermal runaway in a large pack. Flame suppression may not prevent reignition or gas release. Do not approach, carry or submerge a failing battery as a learner exercise.
Lithium-ion product example · Firechief 6 L Lith-Ex
A named product example helps connect the generic table to an actual unit. Confirm the exact product before using its claims.
Agent and intended application
The linked Seton example uses aqueous vermiculite dispersion (AVD) for specified lithium-ion battery fire applications. Water content cools; the dispersed mineral helps form a barrier. This is not generic Class D metal-fire powder.
Read the actual rating
Seton lists a 6 L product with a 13A rating. That A rating describes its solid-material test performance; it does not, by itself, certify a universal Class L battery capability.
Match the exact model and generation
The manufacturer’s current 6 L G2 page identifies FLE6X and different discharge details from the retailer’s older listing. Do not mix their time, range or pressure values. Match the delivered label, product sheet and manual.
Check the battery scope
Confirm the allowed battery chemistry, energy capacity, state and scenario with the current manufacturer information and competent fire assessment. A large EV or energy-storage pack cannot be treated as a small-device fire.
Electrical conditions are product-specific
The supplied product label includes a voltage and minimum-distance condition. Do not transfer that condition to another battery extinguisher or infer that it makes an unsafe electrical approach acceptable.
After the flame disappears
Heat, off-gas and reignition can remain. Follow the planned withdrawal, exclusion and fire-service response; do not pick up, submerge or return a failed battery to charging.
Read the agent, fire-class letters, performance rating, electrical warnings, operating instructions and service condition. Numbers such as 13A or 55B describe standardised test performance, not a safe room size or permission to tackle that amount of fire. Colour is a clue; the actual label and assessed plan decide suitability.
What about a fire blanket?
A fire blanket is separate equipment, not an extinguisher type. It may be specified for a small contained cooking fire, but safe approach and the manufacturer’s limits still matter. Never carry a burning pan, improvise a cover or put yourself between fire and your exit.
Spot the dangerous assumption
Pause at each question, then open the explanation. These are unscored learning prompts alongside the course assessment.
A pan of cooking oil is burning. Would ordinary water help?
No. Rapid steam production can throw burning oil across the room. Raise the alarm and follow the kitchen emergency plan; never move the pan. Only a trained, authorised person should consider the specified F-rated equipment with a safe escape.
There is a C on the powder extinguisher. Should I put out the leaking gas flame?
Not as a routine response. Unburnt gas may continue escaping and form an explosive cloud. Withdraw, alarm and report the supply involved. Any safe isolation and specialist firefighting must follow the assessed emergency arrangements.
The flame around a battery has disappeared. Is the incident over?
No. Internal heat, flammable or toxic off-gas and reignition can remain. Keep clear, prevent access and tell the fire and rescue service what battery is involved. Flame-out is not permission to handle it or restart charging.
Both extinguishers have blue panels. Are the powders interchangeable?
No. Read ABC, BC or the exact Class D metal specification. Colour identifies a family; it does not establish the correct agent, rating or safe application.
A CO₂ extinguisher leaves no mess. Is it ideal in a small unventilated room?
No. A dangerous CO₂ concentration can incapacitate a person, while the fire and smoke already threaten escape. Do not enter an unsafe room. The fire plan and competent equipment selection must account for the space.
A water-mist product claims electrical suitability. Can I use any water extinguisher on a live cabinet?
No. Any tested electrical claim belongs to that particular model, with its own voltage and distance limits. It does not apply to ordinary water or another mist product, and it does not make an unsafe approach acceptable.
Source guidance and scope
UK learning context. Consult the applicable national fire guidance and your premises’ assessed plan. Manufacturer examples explain product variation; they are not product recommendations. Guidance checked 24 October 2026.
Know the alarm, role and immediate protective boundary.
Existing SHAREhub photographic illustration. The written fictional case supplies the condition and decision evidence.
Understand the mechanism and the decision
People respond more reliably when they know how to raise the alarm, what the relevant signal means and where their responsibility ends. A written plan that is unknown or inaccessible during a fault is incomplete as a working arrangement.
Workers need instructions appropriate to their tasks, location, language and access needs. The person raising a concern does not need to become a specialist responder. Use the specified route, give factual location and hazard information and follow the protective instructions that apply to the situation.
Verify the control in the actual task
Check understanding through a meaningful question or exercise and confirm how assistance is obtained if the ordinary communication route fails.
Which emergency roles should be defined?
Emergency roles should be defined before the event so people do not improvise command and communication under pressure.
Roles depend on the size and risk of the organisation. A small office may need an appointed person, fire wardens and a first-aid arrangement. A high-risk site may need incident controller, technical adviser, emergency response team, media lead, security lead, environmental adviser, process shutdown lead and liaison officer.
Roles should include deputies. Emergencies do not wait for the trained person to be on site. Shift, night and weekend cover needs specific attention.
Emergency roles and responsibilities - Emergency roles and responsibilities
Role
Typical responsibility
Evidence
Incident controller
Coordinates internal response and emergency services handover.
Training record and role card.
Fire warden or marshal
Supports evacuation and reports area status.
Warden register and drill feedback.
First aider
Provides first-aid response within competence.
Certificate and first-aid rota.
Technical adviser
Provides site-specific hazard and shutdown information.
Emergency information pack.
Communications lead
Controls messages to staff, visitors, families, media or stakeholders.
Communication plan.
Assembly point coordinator
Accounts for people and reports missing persons.
Roll-call system and drill records.
Security or lockdown lead
Supports public, visitor or threat-related response.
Security procedure and training.
Applied case
A contractor can name the assembly point but does not know how to raise the site alarm from the work area.
Test the assumption
Only the contractor attendance signature. This does not establish acceptance. A location name alone does not establish a workable first response.
Evidence before acceptance
Check understanding through a meaningful question or exercise and confirm how assistance is obtained if the ordinary communication route fails.
Test your decision
What should be resolved before work begins?
Only the contractor attendance signature.
Only the fastest route back to the vehicle.
The usable alarm route and task-relevant protective instructions.
Compare the explanation
The usable alarm route and task-relevant protective instructions.
A location name alone does not establish a workable first response.
Distinguish evacuation, shelter and other protective actions
Distinguish evacuation, shelter and other protective actions.
Photorealistic illustrative UK workplace scene. Review checks: Avoid / redesign: Remove unnecessary hazardous gas inventory or the releasing process through a validated process redesign. Control the task: Provide suitable remote process isolation and separation from occupied areas so the response does not require people to approach a release. Verify before release: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Understand the mechanism and the decision
The appropriate protective action depends on the hazard, its location and development, and the site emergency basis. Moving people can reduce exposure, but an unsuitable route can move them into it. Sheltering also needs a justified arrangement and clear communication rather than an improvised decision.
Follow the authorised instructions for the actual event and location. Do not use a generic wind rule, a zone drawing or a remembered drill route as permission to cross a suspected release. The emergency command arrangements must be able to change instructions as reliable information changes.
Verify the control in the actual task
Know how revised instructions reach people and how those needing assistance receive appropriate planned support.
The protective action must fit the actual scenario
Evacuation, shelter and other protective actions need the planned scenario, current information and authorised instructions. One remembered drill route is not suitable for every release.
Fictional learning example
Separate the evidence from the decision
Part of the picture
What the example establishes
Event
A suspected hazardous release has been reported.
Uncertainty
The release location, extent and safe route are not confirmed.
Accountability
One person is not yet accounted for.
Pause and decide: Should a colleague enter the suspected area to search?
Compare the reasoning
No. Raise the missing-person information through the emergency command arrangements and follow the protective instructions. Give responders factual last-known information. Planned competent rescue, accounting and coordinated decisions are needed; an unplanned entry can create another casualty.
How should muster, shelter and evacuation decisions be made?
Muster, shelter and evacuation decisions should be scenario-based, wind-aware, receptor-aware and clearly communicated.
Evacuation is not always the safest response. A toxic release may require shelter-in-place. A fire may require evacuation away from smoke and escalation zones. A BLEVE risk may require withdrawal to greater distance. A vapour cloud may require ignition-source control and access restriction. The plan should define triggers and fallback decisions.
People accounting must include employees, contractors, visitors, drivers, lone workers and people in remote plant areas. Welfare matters too: prolonged evacuation or sheltering needs information, medical support, drinking water, toilets, weather protection and family communication.
Photorealistic illustrative UK workplace scene. Review checks: Avoid / redesign: Remove unnecessary hazardous gas inventory or the releasing process through a validated process redesign. Control the task: Provide suitable remote process isolation and separation from occupied areas so the response does not require people to approach a release. Verify before release: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Understand the mechanism and the decision
A person in danger may need urgent help, but entering an uncontrolled atmosphere, electrical area or fire can expose an unprotected rescuer too. The first response must consider the continuing hazard and the planned means of obtaining competent assistance.
First aid and specialist rescue are different capabilities. Awareness training does not make a worker a chemical, confined-space or electrical rescuer. Raise the alarm and provide useful information from safety, following the established protective arrangements rather than improvising entry or using unsuitable equipment.
Verify the control in the actual task
Know the assistance and responder access route in advance. Do not infer a safe atmosphere or rescue capability from the urgency of the situation.
How should first aid fit into emergency response?
First aid should be planned from the first-aid needs assessment and integrated with emergency roles, access and handover.
First aid arrangements must suit the work. Low-hazard offices, construction projects, chemical sites, remote work, lone working, public venues and shift work may need different equipment, people and response times.
First aiders should know how to summon help, where equipment is, how to protect themselves and how to hand over to ambulance services. The plan should include AEDs, eyewash, burns kits, rescue equipment or specialist arrangements where risk assessment identifies the need.
Assure the resources and their failure contingencies
Assure the resources and their failure contingencies.
Photorealistic illustrative UK workplace scene. Review checks: Change at source: Remove unnecessary hazardous gas inventory or the releasing process through a validated process redesign. Make it observable: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. Keep useful evidence: Scenario study, internal plan, agency contact, exercise log, equipment check and corrective-action closure.
Understand the mechanism and the decision
Emergency arrangements may depend on alarms, communications, lighting, access, equipment, utility supplies and trained people. A resource list is not proof that each item is available or usable during the scenario. Shared dependencies can remove several capabilities together.
Plan for relevant failures and verify the accepted alternatives through responsible roles. A backup radio or generator needs a defined purpose and assurance; its presence does not establish coverage, operation or competence. Keep unavailable resources visible in the current response information.
Verify the control in the actual task
Compare resource assurance with the credible scenario and record which limitations need a responsible readiness decision before affected work.
What emergency resources and equipment need assurance?
Emergency resources need assurance because a plan is only credible if the people, equipment and supplies are available when needed.
Major accident response may depend on firewater, foam, emergency shutdown systems, gas detection, alarms, public address, radios, breathing apparatus, spill containment, portable monitors, pumps, emergency lighting, first aid, decontamination, welfare facilities and specialist contractors.
Each resource should have an owner, inspection frequency, test method, performance expectation and defect escalation route. If a drill relies on equipment that was not actually deployed, the drill may not prove readiness.
An exercise assumes the main radio channel works, although the scenario includes a power and communication failure.
Test the assumption
Only the normal channel in ideal conditions. This does not establish acceptance. The resource must support the required function under the relevant conditions.
Evidence before acceptance
Compare resource assurance with the credible scenario and record which limitations need a responsible readiness decision before affected work.
Test your decision
What must be tested?
Only the normal channel in ideal conditions.
Only the number of spare radios in the store.
The accepted contingency communication and coordination arrangements under the stated failure.
Compare the explanation
The accepted contingency communication and coordination arrangements under the stated failure.
The resource must support the required function under the relevant conditions.
Existing SHAREhub photographic illustration. The written fictional case supplies the condition and decision evidence.
Understand the mechanism and the decision
An emergency needs clear authority for protective decisions, coordination and information. Roles and escalation must be understood across operations, contractors and responders. Several people giving inconsistent instructions can undermine otherwise useful equipment and plans.
The actual command system should define how reliable information is received, decisions are communicated and authority transfers when appropriate. A job title alone does not establish competence or availability. Workers need to know whose instructions apply and how to report a conflict from safety.
Verify the control in the actual task
Check the defined roles, deputies and handover arrangements and test that the intended recipients can understand the accepted instruction.
How should incident command be structured?
Incident command should define who is in control, how information is logged and how decisions are escalated.
The command structure should be simple enough to work under pressure. For a small site, this may be a duty manager with deputies. For a process site, it may include site incident controller, technical adviser, emergency response leader, communications lead, security/access lead, muster coordinator and senior strategic command.
The command role should not be given to someone only because they are senior. Command requires site knowledge, calm decision-making, authority, communication discipline and training in the emergency plan.
Incident command roles - Incident command roles
Role
Command responsibility
Evidence of readiness
Site incident controller
Sets priorities, directs response and coordinates handover.
Training, rota, exercises and command log.
Technical adviser
Explains plant, substances, isolation, escalation and safe shutdown.
Competence record and emergency information pack.
Emergency response team leader
Controls trained responders and equipment.
Team training and equipment checks.
Muster coordinator
Accounts for people and escalates missing-person information.
Muster drill and roll-call record.
Communications lead
Manages internal updates, emergency contacts and external messages.
Contact list tests and message templates.
Strategic manager
Supports business, regulatory, recovery and resource decisions.
Crisis exercise and leadership review.
The site incident controller manages the operator response and handover. Emergency services command their own response on arrival; the site must keep an accurate shared picture rather than issuing conflicting instructions. See HSE COMAH emergency arrangements inspector guidance.
Applied case
Two separate supervisors give contradictory movement instructions during an exercise.
Test the assumption
Only which supervisor spoke louder. This does not establish acceptance. Conflicting instructions are a system issue to resolve before relying on the response.
Evidence before acceptance
Check the defined roles, deputies and handover arrangements and test that the intended recipients can understand the accepted instruction.
Test your decision
What should the debrief resolve?
Only the order in which messages were sent.
The command, escalation and communication arrangements for a single coordinated protective decision.
Only which supervisor spoke louder.
Compare the explanation
The command, escalation and communication arrangements for a single coordinated protective decision.
Conflicting instructions are a system issue to resolve before relying on the response.
Photorealistic illustrative UK workplace scene. Review checks: Avoid / redesign: Plan the test during a safe shutdown wherever practicable so testing does not leave operating plant dependent on the function being withdrawn. Control the task: Place affected equipment in the required safe state and control energy, inventory and access around moving shutdown equipment. Verify before release: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Understand the mechanism and the decision
Responders need clear location and access information, known materials and hazards, people affected and the current protective or plant state. Facts and uncertainty should be distinguished. Guessing a safe condition or an invented inventory can mislead the response.
The handover must use the established interface and retain updates as the situation changes. Do not enter the affected area to collect extra information unless that is an authorised competent role. Existing plans and current records should support information that can be supplied from safety.
Verify the control in the actual task
Confirm the practical access and contact arrangements through the plan, and ensure relevant updates reach the responsible command interface.
How should handover to emergency services work?
Handover should give emergency services a concise, accurate picture of the hazard, people, access and actions already taken.
Emergency services should not have to discover the site while the incident is escalating. A good handover includes site layout, access route, isolation points, hazardous substances, quantity, location, missing people, casualties, firefighting water, drainage risks, wind direction, utility controls and what the site has already done.
For COMAH and major hazard sites, the interface should be built before the incident through emergency planning, exercises and shared understanding of credible scenarios. See HSE COMAH emergency arrangements inspector guidance.
Account for contractors, visitors and assistance needs
Account for contractors, visitors and assistance needs.
Photorealistic illustrative UK workplace scene. Review checks: Change at source: Remove unnecessary hazardous gas inventory or the releasing process through a validated process redesign. Make it observable: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. Keep useful evidence: Scenario plan, role drill, alarm check, incident log and corrective-action retest.
Understand the mechanism and the decision
A protective response must consider everyone who may be present, including delivery crews, contractors, visitors and people needing assistance. A payroll list alone may not describe the occupied site. Accountability also needs a clear way to report a missing or uncertain person.
Do not send untrained staff back into a hazard to search for someone. Pass the information through the planned command and responder system. Assistance arrangements should be proportionate, respectful and known to those who must use them; do not assume a disability or an individual capability from appearance.
Verify the control in the actual task
Test how records, reports and uncertainty reach the responsible role, including shift changes and people working away from the usual work area.
How should evacuation and places of safety be managed?
Evacuation should move people to a place of safety using routes, exits and assembly arrangements that are suitable for the emergency.
Evacuation is not simply leaving the building. The plan should consider route capacity, blocked routes, smoke, external hazards, traffic, weather, vulnerable people, visitors, contractors, refuge points and roll-call accuracy.
Emergency exits should remain unobstructed and clearly marked. Assembly points should not place people in another hazard, such as near gas cylinders, traffic, blast zones, fire service access or smoke travel. See HSE workplace emergency procedures.
Evacuation controls - Evacuation controls
Control
What good looks like
Evidence
Routes and exits
Enough exits, kept clear and clearly marked.
Inspections and fire risk assessment.
Emergency lighting
Supports safe movement if normal lighting fails.
Test and maintenance records.
Assembly points
Located away from foreseeable hazards.
Site plan and drill feedback.
People accounting
System to identify missing persons quickly.
Roll-call record and visitor system.
PEEPs
Support for people needing assistance.
Confidential plans and drill review.
Re-entry control
No re-entry until authorised.
Incident controller instruction.
Applied case
A delivery crew is absent from the usual staff register during a muster exercise.
Test the assumption
Only the employee attendance list. This does not establish acceptance. The plan must reflect actual occupancy without creating unplanned rescue exposure.
Evidence before acceptance
Test how records, reports and uncertainty reach the responsible role, including shift changes and people working away from the usual work area.
Test your decision
What should be improved?
Only the employee attendance list.
A rule that anyone may re-enter to search.
The site accountability and assistance arrangements for all relevant people.
Compare the explanation
The site accountability and assistance arrangements for all relevant people.
The plan must reflect actual occupancy without creating unplanned rescue exposure.
Design an exercise around a decision that matters.
Photorealistic illustrative UK workplace scene. Review checks: Change at source: Plan the test during a safe shutdown wherever practicable so testing does not leave operating plant dependent on the function being withdrawn. Make it observable: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. Keep useful evidence: Scenario, controller log, exercise observation, agency handover and verified action closure.
Understand the mechanism and the decision
An exercise should test a defined protective objective and the information or resources needed to achieve it. Success is not simply a short evacuation time or a smooth performance under known conditions. Relevant failures and uncertainty can reveal weaknesses that a rehearsed demonstration hides.
Choose a safe fictional scenario and appropriate exercise controls. Participants must know how to distinguish the exercise from a real event and how to stop it if an actual emergency arises. Do not create hazardous releases, interfere with live protection or send real action messages merely for a learning demonstration.
Verify the control in the actual task
Record the objective, observations and limitations honestly; a simulated success is evidence within that test scope, not proof of every emergency capability.
How should an emergency exercise be designed?
An emergency exercise should have clear objectives, credible injects, observers, safety controls and learning outputs.
Exercise design should begin with one or two clear questions: what are we testing and what evidence would prove it works? The answer may be muster accuracy, command handover, responder safety, emergency shutdown, shelter decision, communication to neighbours, emergency services access or action closure.
Good exercises use injects to create uncertainty. Examples include a blocked access road, failed radio channel, missing contractor, injured responder, changing wind direction, unavailable firewater, conflicting alarm information or media enquiry. Injects should stretch the system without creating real danger. See HSE COMAH emergency arrangements inspector guidance.
Hazard, initiating event, consequence and barriers.
Keeps the exercise realistic.
Injects
Complications introduced during the exercise.
Tests decisions under uncertainty.
Observers
People who record facts without interfering.
Provides evidence for debrief.
Exercise safety
Controls to avoid creating real risk.
Protects people during live exercises.
Success criteria
What good performance looks like.
Makes findings fair and useful.
Applied case
A drill is scored only on speed and avoids testing communication failure or changing instructions.
Test the assumption
A faster stopwatch target without a defined safety objective. This does not establish acceptance. Meaningful exercise evidence comes from the required response, not speed or spectacle.
Evidence before acceptance
Record the objective, observations and limitations honestly; a simulated success is evidence within that test scope, not proof of every emergency capability.
Test your decision
What would make the test more useful?
An uncontrolled surprise using live hazardous material.
A safe scenario-led objective testing the relevant protective decisions and contingencies.
A faster stopwatch target without a defined safety objective.
Compare the explanation
A safe scenario-led objective testing the relevant protective decisions and contingencies.
Meaningful exercise evidence comes from the required response, not speed or spectacle.
Photorealistic illustrative UK workplace scene. Review checks: Setting: the process operator drills a tank release with a failed radio and downwind muster point. Act: Declare exercise boundaries and safety controller; confirm that simulation cannot trigger live plant action. Hold / review: Stop an unsafe drill immediately; during a real event stop unprotected entry and escalate missing facts.
Understand the mechanism and the decision
A useful debrief distinguishes what was observed, why it matters and which response function needs improvement. Blaming the last person to speak can miss unclear authority, missing information or inaccessible equipment. Good performance and limitations should both be retained.
Actions need a responsible fictional owner in the exercise and an appropriate verification method. In real operation, the organisation follows its own action system. A revised document or a sent email is not enough if the problem was that an instruction did not reach people under fault conditions.
Verify the control in the actual task
Retest proportionately and retain the result, remaining limitations and review trigger; this course exercise assigns no real workplace action.
How should drill learning be captured and closed?
Drill learning should be captured quickly, analysed properly and tracked until improvements are verified.
A hot debrief immediately after the exercise captures obvious issues while memories are fresh. A cold debrief can then examine logs, timings, observer notes, communications, photographs and feedback. The result should be ranked findings, owners, due dates and evidence of completion.
Learning should be connected to HSG245-style thinking: gather information, analyse what happened, identify better controls and implement the action plan. The most important question is whether the action will make the next response safer and more effective.
Debrief and action closure - Debrief and action closure
Step
What to do
Evidence
Hot debrief
Capture immediate observations and safety issues.
Notes and attendance.
Evidence review
Check logs, timings, radio records and observer notes.
Exercise evidence pack.
Analysis
Identify underlying causes, not only visible symptoms.
Findings and cause analysis.
Action planning
Assign owner, due date, priority and verification method.
Action tracker.
Close-out
Verify the improvement has been made and communicated.
Completion evidence.
Retest
Repeat part of the exercise if the weakness was significant.
Retest record.
Applied case
A failed communication finding is marked closed after an updated plan is circulated, with no test of the fallback route.
Test the assumption
Only the email distribution list. This does not establish acceptance. Improvement must address the observed functional weakness.
Evidence before acceptance
Retest proportionately and retain the result, remaining limitations and review trigger; this course exercise assigns no real workplace action.
Test your decision
What evidence should support closure?
Verification that the revised communication arrangement performs the intended function.
Only the email distribution list.
Only the number of pages changed.
Compare the explanation
Verification that the revised communication arrangement performs the intended function.
Improvement must address the observed functional weakness.
Treat recovery and restart as separate controlled decisions
Treat recovery and restart as separate controlled decisions.
Photorealistic illustrative UK workplace scene. Review checks: Setting: the leisure operator has an evening chemical spill in a plant room. Act: Check alarms, isolation, first-aid cover and access information on the late shift. Hold / review: Unknown substance, blocked route or unprotected entry stops local intervention.
Understand the mechanism and the decision
The end of an obvious event does not establish that equipment, atmosphere, structures or protective systems are fit for re-entry or restart. Damage, residual material, impaired utilities and changed operating conditions can remain after visible smoke or liquid has gone.
Recovery needs the responsible assessment and authorisation, with relevant specialist input and verification. Keep investigation, emergency response and operating acceptance interfaces clear. A production target or an all-clear message outside its defined scope cannot substitute for the required readiness decision.
Verify the control in the actual task
Communicate the accepted plant state and remaining holds explicitly; a course certificate does not authorise post-incident restart.
How should recovery and return to work be managed after an emergency?
Recovery should only begin after serious danger is controlled and the site has been made safe by competent people.
After an emergency, there may be hidden hazards: structural instability, contaminated runoff, damaged electrical systems, chemical residues, smoke contamination, psychological impact, plant damage or evidence that needs preservation.
Recovery should include re-entry control, incident investigation, worker welfare, communication, repair authorisation, business continuity, environmental controls, regulatory reporting and learning. Do not let production pressure drive unsafe restart.
Recovery controls - Recovery controls
Recovery step
Purpose
Evidence
Make safe
Confirm danger is controlled.
Re-entry authorisation.
Account for people
Confirm no one is missing or unsupported.
Roll-call and welfare record.
Preserve evidence
Support investigation and learning.
Scene control and photographs.
Report and notify
Meet legal and stakeholder requirements.
RIDDOR or regulator decision log.
Support people
Address trauma, injury and wellbeing.
Occupational health or EAP route.
Review and improve
Fix weaknesses before recurrence.
Debrief and action tracker.
Applied case
Visible smoke has cleared and production wants to restart before equipment and protective functions are assessed.
Test the assumption
Restart because the area looks normal. This does not establish acceptance. A changed condition needs verified acceptance, not appearance or waiting alone.
Evidence before acceptance
Communicate the accepted plant state and remaining holds explicitly; a course certificate does not authorise post-incident restart.
Test your decision
What is the defensible response?
Restart because the area looks normal.
Use elapsed time as the only release criterion.
Retain the relevant restrictions until the authorised re-entry/recovery and readiness requirements are met.
Compare the explanation
Retain the relevant restrictions until the authorised re-entry/recovery and readiness requirements are met.
A changed condition needs verified acceptance, not appearance or waiting alone.
Reconcile the complete response and external interface
Reconcile the complete response and external interface.
Photorealistic illustrative UK workplace scene. Review checks: Setting: the process operator practises a tank overfill leading to a vapour release and possible explosion. Act: Confirm containment, detection, alarm, isolation, command succession and alternative shelter or evacuation routes. Hold / review: Failed detector, blocked route, unknown wind direction or absent command lead triggers a safe hold and escalation.
Understand the mechanism and the decision
A major emergency can require coordination beyond the immediate work group, including neighbours, external responders and other responsible bodies as applicable to the site and jurisdiction. Internal arrangements must connect with those interfaces and use current reliable information.
The combined exercise reveals failed communication, incomplete delivery-crew accountability and premature recovery pressure. Each observation affects a different part of the protective chain. The responsible improvement decision must retain uncertainty, fix the relevant system weaknesses and verify the agreed response before claiming readiness.
Verify the control in the actual task
Keep the exercise record factual and fictional here. Actual emergency plans, external communications and operating releases remain within the organisation authorised system.
What off-site interfaces must be planned?
Off-site interfaces include emergency services, the relevant external-plan lead, neighbours, the public, environmental responders, media and mutual aid partners. For upper-tier COMAH, the external-plan lead differs between Great Britain and Northern Ireland.
Major accidents do not respect the fence line. Smoke, vapour, blast, fragments, contaminated water, road closures, public fear and media attention can all leave the site boundary quickly. Emergency plans should define who contacts whom, what information is given, how updates are issued and who speaks publicly.
For upper-tier COMAH sites in Great Britain, the local authority prepares the external emergency plan, using information from the operator. See GB COMAH regulation 13. In Northern Ireland, the Executive (HSENI) arranges the external emergency plan and consults designated authorities under NI COMAH regulation 13. The operator must supply scenario, consequence, warning and response information to the appropriate lead. Do not assign the GB local-authority lead to an NI site.
External interface map - External interface map
Interface
Why it matters
Evidence
Emergency services
Need early accurate information and site hazards.
Rendezvous point and joint exercises.
External-plan lead: GB local authority; NI Executive (HSENI)
Prepares or arranges the upper-tier external plan under the applicable COMAH rules.
Operator information submission, consultation and plan review.
Regulator
Notification, investigation and enforcement interface.
COMAH and incident communication record.
Neighbouring sites
Domino and shared emergency impacts.
Mutual aid and warning arrangements.
Public
Warning, advice and reassurance.
Public information and message templates.
Environment agency/interface
Runoff, pollution and environmental monitoring.
Containment and notification plan.
Applied case
The exercise ends quickly, but fallback communication, contractor accountability and recovery authorisation all failed their objectives.
Test the assumption
Declare full readiness because the exercise finished quickly. This does not establish acceptance. A completion time cannot override failed protective objectives.
Evidence before acceptance
Keep the exercise record factual and fictional here. Actual emergency plans, external communications and operating releases remain within the organisation authorised system.
Test your decision
What should the readiness conclusion be?
Remove the difficult findings from the final report.
Record the limitations, implement the responsible improvements and verify the affected functions before claiming those objectives are met.
Declare full readiness because the exercise finished quickly.
Compare the explanation
Record the limitations, implement the responsible improvements and verify the affected functions before claiming those objectives are met.
A completion time cannot override failed protective objectives.
Study a completed fictional industrial construction and commissioning plan. Compare its warning, roles, accountability, responder access, rescue limits and recovery decisions with the learning above. It includes a new fictional site schematic, a worked exercise and separate blank recording annexes.
Use this as a teaching example when developing arrangements for your own premises. The fictional layout and role identifiers are not live emergency instructions.