Hazardous material behaviour and compatibility

Approx. 85–120 minutes

Independent SHAREhub process-safety awareness using fictional cases and a Great Britain baseline; check the applicable Northern Ireland duties and actual site arrangements. This course does not award a NEBOSH qualification, establish specialist competence or authorise hazardous work.

This reader supplies the complete teaching. Use the interactive LMS course for assessed activities, saved progress and completion.

LESSON 1

Distinguish a hazardous property from the task risk

Distinguish a hazardous property from the task risk.

Closed pipework and vessels in a UK chemical processing plant
Existing SHAREhub photographic illustration. The written fictional case supplies the condition and decision evidence.

Understand the mechanism and the decision

A hazardous property describes what a substance can do; risk depends on the material, amount, form, activity and people exposed. A familiar trade name does not establish the full range of fire, reaction or health hazards in a changed task.

Assess the credible scenario rather than collecting labels alone. A closed container on a shelf and the same material sprayed, heated or transferred can present different pathways. Control choices must address the actual operation and foreseeable failures.

Verify the control in the actual task

Use current identity and supplier information with the responsible assessment; do not extend an old task approval by assumption.

What are dangerous substances and hazardous properties?

A hazardous property describes what a material can do; risk depends on whether that property can cause harm in the actual work. A sealed solvent container and the same solvent sprayed beside an ignition source have different risks.

This page uses a broad chemical-hazard scope. The legal term dangerous substance under DSEAR has a specific physical-safety meaning. Toxicity or environmental harm alone is not a reason to describe a material as falling within DSEAR. GB DSEAR also covers gases under pressure and substances corrosive to metals; health exposure is assessed separately under COSHH. See DSEAR in detail and the NI routes below.

A fire needs fuel, an oxidising agent and ignition. Dispersing combustible material as vapour, mist or dust can make rapid burning possible; confinement and congestion can increase damaging pressure. A reactive material can also release heat or gas without an external flame. If heat generation overtakes heat removal, the reaction can accelerate, raising temperature and pressure. Whether this can happen requires material and process evidence, not a guess from the product name.

Health effects may be immediate, such as chemical burns or poisoning, or develop after repeated exposure or long delay, such as dermatitis, occupational asthma or cancer. Exposure may occur by breathing, skin or eye contact, swallowing contamination or skin puncture. Absence of a strong smell, visible cloud or immediate symptoms does not demonstrate control.

Useful terms: The inventory is the amount present, including material connected to a possible release. Loss of containment means an unintended escape. Compatibility means suitability for contact with other substances and equipment under the expected conditions. A credible scenario describes a plausible chain from failure to harm.

Applied case

A familiar cleaner is introduced into a heated process rather than its usual wipe-cleaning task.

Test the assumption

Only whether the product name is familiar. This does not establish acceptance. The same product can present different risks when the activity changes.

Evidence before acceptance

Use current identity and supplier information with the responsible assessment; do not extend an old task approval by assumption.

Test your decision

What must be reviewed for this new use?

  1. The actual material properties, process conditions and credible exposure or reaction scenarios.
  2. Only whether the product name is familiar.
  3. Only whether the old task had an accident.
Compare the explanation

The actual material properties, process conditions and credible exposure or reaction scenarios.

The same product can present different risks when the activity changes.

Open this interactive lesson →

LESSON 2

Resolve the exact identity before accepting a delivery

Resolve the exact identity before accepting a delivery.

Closed pipework and vessels in a UK chemical processing plant. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Avoid / redesign: Remove an unnecessary solvent use or open decanting step through process redesign. Control the task: Use an assessed dedicated dispensing area separated from ignition sources, occupied routes and incompatible materials. Verify before release: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.

Understand the mechanism and the decision

Identity includes the actual substance or mixture and relevant grade or composition. Similar names, compatible-looking containers and a regular supplier do not resolve a discrepancy between an order, label and delivery information.

A review must reconcile the material with the intended receiving system. Where identity remains uncertain, containment and controlled hold arrangements are needed through the site system. Sampling or relabelling by guesswork can add exposure and conceal the uncertainty.

Verify the control in the actual task

Keep the container identified as unconfirmed under the actual site arrangements and communicate the hold to the receiving team.

Check the changed delivery before transfer

What must be checked before a zoned workplace first operates?Open the existing guidance for this part of the decision.How do DSEAR and COSHH fit together?Open the existing guidance for this part of the decision.What should happen when identity or compatibility is uncertain?Open the existing guidance for this part of the decision.

A familiar product name is insufficient when concentration or composition changes. Check the receiving system, residues, capacity and safeguards together; use the health and physical-risk assessments for their different purposes.

Best-practice guide · six simple steps

Best-practice guide: Dangerous substances and hazardous properties

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · Start
Download imagesThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. Check the changed delivery before transfer

    A familiar product name is insufficient when concentration or composition changes.

    • Avoid / redesign: Remove an unnecessary solvent use or open decanting step through process redesign.
    • Control the task: Use an assessed dedicated dispensing area separated from ignition sources, occupied routes and incompatible materials.
    • Verify before release: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.

    A familiar product name is insufficient when concentration or composition changes. Check the receiving system, residues, capacity and safeguards together; use the health and physical-risk assessments for their different purposes. Dangerous substances can cause fire, explosion, harmful reactions or other physical harm; hazardous properties also include effects on health and the environment.

    Apply it: Which part of this plan would you check at the workface before authorising the task?

    Read this part of the full topicOpen the full topicDSEAR in detail (Great Britain)COSHH assessment (Great Britain)Control of Substances Hazardous to Health (Northern Ireland)
  2. 2. Turn dangerous substances and hazardous properties knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: Remove an unnecessary solvent use or open decanting step through process redesign.
    • Make it observable: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
    • Keep useful evidence: Record the discovery, isolation of the affected task, identity evidence or specialist disposal decision, contractor instructions and supervisor hand-back.

    Dangerous substances can cause fire, explosion, harmful reactions or other physical harm; hazardous properties also include effects on health and the environment. Understand the exact material and task, control release and exposure, and stop when identity, compatibility or safeguards are uncertain. Record the discovery, isolation of the affected task, identity evidence or specialist disposal decision, contractor instructions and supervisor hand-back.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicOfficial task guidance: www.hse.gov.uk (Great Britain)Chemical safety data sheets (Great Britain)COSHH assessment (Great Britain)
  3. 3. Worked example an unlabelled container during maintenance

    Fictional example: a practical application of the existing topic lesson.

    • Setting: A maintenance team finds an unlabelled closed container in the process operator’s covered chemical store while preparing to clean a dosing system.
    • Act: Stop the dependent cleaning step, leave the container closed and restrict access as the local procedure requires.
    • Hold / review: No mixing, decanting, drain disposal or restart while identity is unresolved.

    The responsible specialist checks container condition, identity evidence, residue and waste compatibility, and specifies any handling needed. Brief the contractor on the verified hazards and route. After approved handling or removal, confirm the system, store and waste arrangements match the assessment.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicChemical safety data sheets (Great Britain)COSHH assessment (Great Britain)Control of Substances Hazardous to Health (Northern Ireland)
  4. 4. A hazardous property needs a credible event route

    Connect the task, the route to the person and the control that can fail.

    • Release: A leak, spill or dust release brings dangerous material into the work area.
    • Event: Ignition, reaction or loss of pressure control can produce fire, explosion or another harmful event.
    • People: Workers and neighbours may be exposed along the actual release or escalation path.

    A leak, spill or dust release brings dangerous material into the work area. Ignition, reaction or loss of pressure control can produce fire, explosion or another harmful event. Workers and neighbours may be exposed along the actual release or escalation path. Use the full topic for the detailed mechanism, task limits and source scope.

    Apply it: Where is this harm route present in the actual work, and which control breaks it before anyone is exposed?

    Read this part of the full topicOpen the full topicDSEAR in detail (Great Britain)COSHH assessment (Great Britain)Control of Substances Hazardous to Health (Northern Ireland)
  5. 5. Choose controls for dangerous substances and hazardous properties

    Start with the stronger practicable options and verify their effect.

    • Elimination: Remove an unnecessary solvent use or open decanting step through process redesign.
    • Substitution: Validate a suitable less flammable product or solvent-free method against operating temperature, quality and new hazards.
    • Engineering controls: Use an assessed dedicated dispensing area separated from ignition sources, occupied routes and incompatible materials.
    • Engineering controls: Provide compatible closed transfer, containment and ventilation, with assessed electrical, bonding and earthing measures where required.
    • Administrative controls: Verify product identity, receiving capacity, connections and spill response; prevent unapproved containers and hot work in the affected area.

    Elimination: Remove an unnecessary solvent use or open decanting step through process redesign. Substitution: Validate a suitable less flammable product or solvent-free method against operating temperature, quality and new hazards. Engineering controls: Use an assessed dedicated dispensing area separated from ignition sources, occupied routes and incompatible materials. Engineering controls: Provide compatible closed transfer, containment and ventilation, with assessed electrical, bonding and earthing measures where required. Administrative controls: Verify product identity, receiving capacity, connections and spill response; prevent unapproved containers and hot work in the affected area. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

    Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

    Read this part of the full topicOpen the full topicOfficial task guidance: www.hse.gov.uk (Great Britain)
  6. 6. Use the full dangerous substances and hazardous properties lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: DSEAR in detail
    • Official guidance: COSHH assessment
    • Task decision: Record the discovery, isolation of the affected task, identity evidence or specialist disposal decision, contractor instructions and supervisor hand-back.

    Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicDSEAR in detail (Great Britain)COSHH assessment (Great Britain)Control of Substances Hazardous to Health (Northern Ireland)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

Changed chemical delivery

Illustrative example. A replacement delivery has the same connector but a different concentration.

Decision. The receiving owner checks identity, compatibility and the actual transfer conditions before accepting it.

Evidence to check. Current product information, destination identity, compatible residues and verified transfer controls.

Hold or escalation point. Hold transfer while composition, destination or compatibility is unresolved.

Follow-up. Record the decision and revise procurement and receiving instructions if the change will recur.

Sources and references

Read with: DSEAR in detail · COSHH assessment · HSENI guidance · GB CLP or EU CLP in NI.

Applied case

A delivery note names a different grade from the receiving plan, although the containers look identical.

Test the assumption

Connect it because the container colour matches. This does not establish acceptance. A visual match cannot establish material identity or compatibility.

Evidence before acceptance

Keep the container identified as unconfirmed under the actual site arrangements and communicate the hold to the receiving team.

Test your decision

What is the appropriate acceptance decision?

  1. Connect it because the container colour matches.
  2. Relabel it with the familiar product name.
  3. Hold acceptance into the process until the discrepancy is resolved through the responsible review.
Compare the explanation

Hold acceptance into the process until the discrepancy is resolved through the responsible review.

A visual match cannot establish material identity or compatibility.

Open this interactive lesson →

LESSON 3

Connect physical form with the exposure pathway

Connect physical form with the exposure pathway.

Closed pipework and vessels in a UK chemical processing plant. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Change at source: Remove an unnecessary solvent use or open decanting step through process redesign. Make it observable: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls. Keep useful evidence: Record the discovery, isolation of the affected task, identity evidence or specialist disposal decision, contractor instructions and supervisor hand-back.

Understand the mechanism and the decision

Liquids, vapours, aerosols and dusts can move and expose people differently. A task may create a hazardous form that is not obvious from the original packaged product. Release, spread, contact and ignition must be considered in the relevant conditions.

A glove or a ventilation claim addresses only a defined part of a control system. Prefer arrangements that avoid or contain release where practicable, and verify their suitability for the substance and task. Appearance and odour cannot reliably determine exposure or atmosphere safety.

Verify the control in the actual task

Ask which route the selected controls address and what evidence supports their effectiveness; do not invent a safe concentration from a sensory observation.

Connect material form to the route of harm

A hazard classification describes properties; the task and physical form determine how people, plant and the environment may be exposed.

Fictional learning example

Separate the evidence from the decision
Part of the pictureWhat the example establishes
LiquidA release can spread, form a pool or generate hazardous vapour.
Gas or vapourA release can disperse beyond the immediate work area and may be invisible.
Powder or mistDispersion changes exposure and may create ignition or explosion hazards where the material and conditions permit.

Pause and decide: Is reading one hazard pictogram enough to approve a new transfer?

Compare the reasoning

No. Confirm identity, properties, task conditions, compatibility, destination and credible release path. Use the relevant safety data and process information together. Review wrong connections, shared drains, waste and cleaning returns as possible mixing routes.

How do physical forms and exposure routes change the risk?

Physical form and route of exposure change how a substance escapes, travels, contacts people and causes harm.

A liquid may splash skin, evaporate into vapour, form a mist during spraying, contaminate surfaces or enter drains. A powder may become airborne during tipping, settle on surfaces, form an explosible dust cloud, be ingested through poor hygiene or contaminate clothing. A gas may travel quickly, displace oxygen, form a flammable cloud or create a toxic atmosphere in a low area.

COSHH good practice requires consideration of relevant exposure routes including inhalation, skin and ingestion. For dangerous substances, DSEAR adds the safety question: could the substance create fire, explosion, energetic reaction or corrosion-related structural failure?

Forms and routes
Form or route Why it matters Control focus
Gas Can disperse, collect in low/high areas depending on density, displace oxygen or form explosive mixtures. Detection, ventilation, isolation, emergency response and confined-space controls.
Vapour Can travel from liquid sources and ignite away from the release point. Containment, temperature control, ventilation and ignition control.
Mist or aerosol Can increase inhalation exposure and flammable surface area. Enclosure, LEV, spray control, respiratory protection and ignition control.
Dust or powder Can be inhaled, contaminate surfaces or form explosible clouds. Dust suppression, extraction, housekeeping, segregation and explosion controls.
Skin and eye contact Can cause burns, sensitisation, absorption or eye injury. Substitution, closed handling, gloves, face protection, eyewash and hygiene.
Ingestion Can occur through contaminated hands, food, cigarettes or surfaces. Welfare, hygiene, cleaning and no eating/drinking in contaminated areas.

Applied case

A low-volatility liquid is proposed for an aerosol-producing task without a revised assessment.

Test the assumption

Only the original liquid appearance. This does not establish acceptance. The task can create an exposure form that the previous assessment did not address.

Evidence before acceptance

Ask which route the selected controls address and what evidence supports their effectiveness; do not invent a safe concentration from a sensory observation.

Test your decision

Which change matters to the review?

  1. Only whether a strong smell is noticed.
  2. The aerosol and its release/exposure pathway under the actual operating conditions.
  3. Only the original liquid appearance.
Compare the explanation

The aerosol and its release/exposure pathway under the actual operating conditions.

The task can create an exposure form that the previous assessment did not address.

Open this interactive lesson →

LESSON 4

Explain the consequences of incompatible mixing

Explain the consequences of incompatible mixing.

Technician working at a fume cupboard in a chemical laboratory
Existing SHAREhub photographic illustration. The written fictional case supplies the condition and decision evidence.

Understand the mechanism and the decision

Incompatible substances can release heat, gas or hazardous products, and some combinations can create pressure or fire. The outcome depends on the actual materials and conditions. Harmless separate storage does not establish that mixing is acceptable.

Do not choose a neutraliser, dilution or mixing order from a general awareness example. Compatibility decisions need competent information for the defined mixture, concentration, temperature and receiving system. Preventing substances from meeting is stronger than relying on a response after an unplanned reaction begins.

Verify the control in the actual task

Use the actual segregation and waste arrangements, retain uncertainty and obtain the responsible specialist review.

What reactions can incompatible chemicals cause?

Incompatible chemicals can generate toxic gas, heat, pressure, fire, explosion, corrosive release, unstable products or environmental contamination.

The most recognised example is acid mixed with sodium hypochlorite bleach, which can release chlorine gas. Other examples include acids with cyanides or sulphides producing toxic gases, oxidisers with organic or flammable materials increasing fire risk, and water-reactive substances producing heat or flammable gas.

Some reactions are immediate and obvious; others develop in a waste container, drain, bund or tank after people leave. Heat, bulging drums, hissing, discolouration, unexpected odour, gas, foaming, pressure rise or unusual crystallisation should be treated as warning signs.

A compatibility assessment should consider chemical family, concentration, quantity, temperature, impurities, water, pH, contaminants, container material and the consequences if the mixture occurs in a confined or enclosed space.

Common incompatibility outcomes
Incompatibility Possible reaction Typical control
Acid plus hypochlorite bleach Chlorine gas release. Segregate, label, train and never mix cleaning chemicals.
Acid plus alkali Heat generation, boiling, splashing and pressure. Segregate and control neutralisation by competent people only.
Oxidiser plus organic or flammable material Fire, rapid reaction or explosion. Separate oxidisers from fuels, solvents, oils and combustibles.
Water-reactive substance plus water Heat, gas, fire or violent reaction. Keep dry and use suitable emergency response.
Cyanide or sulphide plus acid Highly toxic gas release. Segregate and prevent acid contamination.
Incompatible waste streams Gas, heat, pressure, fire or drum rupture. Approve waste streams and test compatibility before bulking.

A hazard-class storage chart is only a starting point. HSE HSG71, paragraph120 warns that substances grouped as compatible can still react; its examples include acid with hypochlorite, cyanide, sulphide or alkali. Check the actual products, residues and leak/drain paths using SDS and competent chemistry advice. This 2009 guidance supports the reaction/segregation principles; its historical legislative references are not the current supply-law route.

Applied case

Two unknown residual liquids are proposed for a common collection drum.

Test the assumption

Combine a small amount to see whether it reacts. This does not establish acceptance. An improvised trial or dilution is not a justified compatibility assessment.

Evidence before acceptance

Use the actual segregation and waste arrangements, retain uncertainty and obtain the responsible specialist review.

Test your decision

What is the defensible decision?

  1. Keep them from being combined until identity and compatibility have been competently established.
  2. Combine a small amount to see whether it reacts.
  3. Add water to make every possible mixture safe.
Compare the explanation

Keep them from being combined until identity and compatibility have been competently established.

An improvised trial or dilution is not a justified compatibility assessment.

Open this interactive lesson →

LESSON 5

Use safety data as evidence rather than a complete approval

Use safety data as evidence rather than a complete approval.

Technician working at a fume cupboard in a chemical laboratory. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Avoid / redesign: Remove an unnecessary product or cleaning step so bleach and acid do not need to be used together in the task. Control the task: Store incompatible products separately in suitable containment and keep dedicated, clearly identified dispensing equipment. Verify before release: If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls.

Understand the mechanism and the decision

Safety data sheets can support identification, hazards, handling, storage and incompatibility review. They do not automatically answer every question about a particular process mixture, waste stream or modified operating condition. Gaps need resolving rather than being read as permission.

Compare the information with the actual concentration, material state and process conditions. A general compatibility chart is a screening aid with a defined scope; it cannot establish the behaviour of every product grade or contaminated residue. Technical acceptance remains a task-specific decision.

Verify the control in the actual task

Record what the source covers and what remains unknown. Obtain the supplier or technical information needed for the responsible acceptance decision.

How should chemical compatibility be assessed?

Compatibility should be assessed by reviewing the chemical inventory, SDS information, reaction hazards, storage locations, transfer routes, drains, waste streams and credible mixing scenarios.

Start with the inventory. List all chemicals, wastes, residues, cleaning chemicals, intermediates, off-spec materials and process fluids. Then identify what could meet what: shelves, bunds, drains, hoses, fill points, waste containers, shared equipment, cleaning routines and emergency response materials.

The SDS is important, especially sections on handling, storage, stability and reactivity, but it does not know your pipework, drain route, container choices or work sequence. A site-specific compatibility review should connect the SDS with the physical workplace.

For higher-risk operations, create credible scenarios: acid into hypochlorite tank, oxidiser into solvent waste, wrong road tanker connection, incompatible drain discharge, cleaning chemical into process residue, rainwater into water-reactive store, or waste drum bulking error.

Compatibility assessment steps
Step What to assess Evidence
Inventory Products, raw materials, intermediates, wastes, residues and cleaners. Chemical register and waste register.
SDS review Sections 7, 8, 10, 11 and 13. SDS review record.
Compatibility matrix Which substances or classes must be separated. Matrix or segregation chart.
Physical layout Stores, bunds, shelves, tanks, drains, transfer points and routes. Marked plan and inspection.
Credible scenarios Wrong transfer, leak mixing, drain mixing, waste bulking and cleaning residues. Risk assessment or HAZOP/what-if review.
Barrier review Labels, locks, couplings, interlocks, permits, procedures and supervision. Barrier register and test records.

Applied case

A chart groups two products broadly but contains no information about the contaminated mixture in the return line.

Test the assumption

Treat the blank detail as confirmation of compatibility. This does not establish acceptance. Missing detail is an evidence gap, not a safe result.

Evidence before acceptance

Record what the source covers and what remains unknown. Obtain the supplier or technical information needed for the responsible acceptance decision.

Test your decision

What should happen before accepting the return route?

  1. Treat the blank detail as confirmation of compatibility.
  2. Rely on the chart colour without reading its scope.
  3. Resolve the actual mixture and conditions through a competent compatibility assessment.
Compare the explanation

Resolve the actual mixture and conditions through a competent compatibility assessment.

Missing detail is an evidence gap, not a safe result.

Open this interactive lesson →

LESSON 6

Prevent a wrong connection before transfer begins

Prevent a wrong connection before transfer begins.

Technician working at a fume cupboard in a chemical laboratory. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Change at source: Remove an unnecessary product or cleaning step so bleach and acid do not need to be used together in the task. Make it observable: If the hazardous step remains, retain a task assessment and select the stronger feasible remaining controls. Keep useful evidence: Monthly review and change trigger.

Understand the mechanism and the decision

Wrong-material events can begin with a familiar hose, a similar coupling or an assumption about where a line ends. Clear identification and a controlled connection system reduce dependence on memory. The receiving system must be checked as part of the whole route.

Verification should establish the material, source, destination and suitability of the route using the approved arrangement. A second person is useful only when they carry out an effective independent check with the relevant information; two signatures on the same assumption do not provide it.

Verify the control in the actual task

Check how the specified controls prevent or detect an incorrect route and who can stop the transfer if the evidence does not agree.

How should deliveries and transfers be verified?

Identify the substance, tank and connection independently before opening a transfer path; stop if any identity or barrier is uncertain.

Compare the order, delivery note, container/tank label, SDS and authorised route. A receiving operator should verify the fixed tank and line against a current line map, while the driver checks the vehicle and hose. Dedicated or non-interchangeable couplings, locked and labelled fill points and suitable interlocks protect against a plausible wrong connection. Treat a missing label, unlocked alternative fill line, bypassed interlock or disagreement as a stop condition. The US CSB MGPI case illustrates why a verbal confirmation alone cannot compensate for confusing fill-point design.

On a small screen, scroll this table sideways to read all columns.

Transfer barriers and failure response
Barrier and ownerCheck and evidenceStop/repair
Chemical identity — buyer/receiving leadMatch product, SDS, order and tank inventory; record independent check.Hold delivery if any identity conflicts.
Connection — engineer/operatorInspect dedicated fitting, unique label, locked unused lines and line map.Do not connect if fitting or line is ambiguous.
Transfer — operator and driverAgree sequence, monitoring, shutoff and emergency signal before flow.Stop flow and isolate safely after alarm, leak or unexpected change.
Change — process safety leadReview temporary hose, tank or supplier changes before use.Do not restart after bypass until authorised correction is verified.

Applied case

A cleaner line and product line have similar connections and the receiving identity is obscured.

Test the assumption

Choose the connection nearest the delivery vehicle. This does not establish acceptance. A trial transfer can introduce the wrong material before the uncertainty is resolved.

Evidence before acceptance

Check how the specified controls prevent or detect an incorrect route and who can stop the transfer if the evidence does not agree.

Test your decision

What is the safe planning response?

  1. Start gently to see which tank level changes.
  2. Resolve the identities and approved connection verification before the proposed transfer.
  3. Choose the connection nearest the delivery vehicle.
Compare the explanation

Resolve the identities and approved connection verification before the proposed transfer.

A trial transfer can introduce the wrong material before the uncertainty is resolved.

Open this interactive lesson →

LESSON 7

Treat segregation as a physical pathway question

Treat segregation as a physical pathway question.

Technician working at a fume cupboard in a chemical laboratory. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Chemical register: Compatibility class, SDS section 10, storage, owner and approved use. Transfer verification: Right product, tank, hose, valve lineup and ullage confirmed. Storage segregation: Acids, alkalis, oxidisers, flammables and wastes separated.

Understand the mechanism and the decision

Segregation needs to prevent incompatible materials meeting through credible routes. Shelving labels alone may not address leaks, shared containment, damaged packages, handling errors or firefighting water. The arrangement must fit the materials and the actual store.

Consider the complete escape route of a release, including low points and drains. A single bund or sump can defeat apparent separation if incompatible materials collect there together. Selection of segregation, containment and drainage arrangements needs the responsible technical assessment rather than a universal distance from a training example.

Verify the control in the actual task

Compare the physical arrangement with the intended segregation basis and keep limitations visible until the required controls are verified.

How should incompatible chemicals be stored and segregated?

Chemicals should be stored so leaks, breakages, fire water, rainwater, vapours or container failure cannot bring incompatible substances together.

Segregation should be based on real compatibility, not only alphabetic order or convenience. Acids and alkalis should normally be separated; oxidisers should be separated from flammables and combustibles; toxic, cyanide, sulphide, water-reactive and peroxide-forming materials may need specialist controls.

Secondary containment matters. If two incompatible liquids share the same bund, they may mix when containers leak. If chemicals are stacked with incompatible materials above or below each other, a leak can drip into the wrong class.

Storage must be maintained: labels legible, containers closed, shelves compatible, spill kits suitable, expired or unstable chemicals removed, and stock levels controlled.

Segregation controls
Storage issue Why it matters Good practice
Acids and alkalis Can react with heat and splashing. Separate cabinets, trays or bays.
Oxidisers and flammables Can intensify fire or cause violent reaction. Dedicated segregated storage.
Hypochlorite and acids Can release chlorine gas. Never store or use together without controlled process design.
Waste chemicals Composition may be uncertain. Label, characterise and segregate waste streams.
Shared bunds Leaks can mix in containment. Use compatible bunding and separate containment.
Decanted containers Missing identity creates wrong use and wrong disposal. Approved labelled containers only.

A hazard-class storage chart is only a starting point. HSE HSG71, paragraph120 warns that substances grouped as compatible can still react; its examples include acid with hypochlorite, cyanide, sulphide or alkali. Check the actual products, residues and leak/drain paths using SDS and competent chemistry advice. This 2009 guidance supports the reaction/segregation principles; its historical legislative references are not the current supply-law route.

Applied case

Separate labelled shelves drain into one collection point for incompatible products.

Test the assumption

Only whether the shelf labels are readable. This does not establish acceptance. Surface separation does not establish segregation through a shared containment route.

Evidence before acceptance

Compare the physical arrangement with the intended segregation basis and keep limitations visible until the required controls are verified.

Test your decision

Which issue needs resolving?

  1. The common leak and drainage pathway that can bring the materials together.
  2. Only whether the shelf labels are readable.
  3. Only the order of products in the stock list.
Compare the explanation

The common leak and drainage pathway that can bring the materials together.

Surface separation does not establish segregation through a shared containment route.

Open this interactive lesson →

LESSON 8

Control waste and cleaning-return uncertainty

Control waste and cleaning-return uncertainty.

2D teaching diagram: Route the product. Prove the work boundary.
Existing SHAREhub 2D teaching schematic. Use alongside the explanation and fictional case in this lesson.

Understand the mechanism and the decision

Waste can differ from the original product because it contains residues, contaminants or mixtures from several tasks. An unlabelled drum cannot be classified safely by colour or a remembered description. Common drains can also connect materials that were separate during normal use.

Identify the source and contents through the actual waste and cleaning systems. Keep uncertain streams separate under controlled arrangements and obtain competent assessment. A disposal label or collection booking does not demonstrate that the contents are compatible with another stream.

Verify the control in the actual task

Check the receiving facility requirements and authorised waste arrangements through the responsible roles; no learner exercise submits a real waste record.

Why are waste streams and drains high-risk mixing routes?

Waste streams and drains are high-risk because chemicals can meet out of sight after leaving the original task area.

A drain, sump, interceptor, IBC, drum or waste tank can become the mixing vessel. Workers may think each individual disposal was small, but incompatible discharges can accumulate or react in a confined space, generating heat, pressure, gas or pollution.

Waste compatibility needs a positive approval process. Unknown waste should not be bulked because it looks similar or because the container is available. Waste labels should include contents, hazards, source, date, incompatible materials and owner.

Drain maps and isolation points are important for process sites, laboratories, workshops and construction sites. If responders do not know where a drain goes, they cannot confidently control a spill or incompatible discharge.

Waste and drain controls
Control Purpose Evidence
Waste-stream approval Prevents incompatible waste from being bulked. Waste acceptance or approval record.
No unknown bulking rule Prevents reaction from unidentified material. Quarantine and characterisation procedure.
Drain map Shows where spills and discharges may travel. Current site drainage plan.
Drain protection Stops incompatible or polluting material entering drainage. Drain covers, valves and spill drills.
Waste labels Communicate contents and hazards. Label inspection and waste register.
Compatibility testing Confirms bulking is safe where required. Test record and acceptance criteria.

Applied case

An unlabelled cleaning-return container is offered for bulking with known waste to save space.

Test the assumption

Bulk it because both containers came from cleaning. This does not establish acceptance. Task origin and smell do not establish composition or compatibility.

Evidence before acceptance

Check the receiving facility requirements and authorised waste arrangements through the responsible roles; no learner exercise submits a real waste record.

Test your decision

What should the team decide?

  1. Bulk it because both containers came from cleaning.
  2. Use smell to assign it to the nearest waste category.
  3. Retain a controlled separate hold until identity and the approved waste route are resolved.
Compare the explanation

Retain a controlled separate hold until identity and the approved waste route are resolved.

Task origin and smell do not establish composition or compatibility.

Open this interactive lesson →

LESSON 9

Review a substitution across the whole process

Review a substitution across the whole process.

Closed pipework and vessels in a UK chemical processing plant. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: A maintenance team finds an unlabelled closed container in the process operator’s covered chemical store while preparing to clean a dosing system. Act: Stop the dependent cleaning step, leave the container closed and restrict access as the local procedure requires. Hold / review: No mixing, decanting, drain disposal or restart while identity is unresolved.

Understand the mechanism and the decision

A replacement product can change composition, hazardous properties, material compatibility or waste behaviour. A supplier describing it as equivalent does not demonstrate equivalence in every process condition. The change review must connect the substitution with the actual use.

Consider receiving, storage, transfer, reaction, cleaning and disposal rather than the main production step alone. New packaging or couplings can also alter error routes. Approval should identify the accepted scope, required controls and updated information before the changed arrangement becomes normal practice.

Verify the control in the actual task

Follow the substance through its lifecycle and verify that relevant procedures, identification and role briefings reflect the accepted change.

What should happen when identity or compatibility is uncertain?

Keep the material out of use and obtain competent confirmation before storage, transfer, mixing or disposal. Similar appearance, colour, smell or a container that fits is not evidence of compatibility.

Check the current supplier information against the exact formulation, concentration, process temperature, pressure and intended contact. Include seals, hoses, tank linings, residues, shared bunds, drains and waste containers. An SDS is an input; unusual reactions or process conditions may need supplier advice, a chemist or a reaction-hazard study.

Worked example an unlabelled container during maintenance

Task material and setting: A maintenance team finds an unlabelled closed container in Crownway’s covered chemical store while preparing to clean a dosing system. The planned outcome is a clean, handed-back system without mixing an unknown material into the process or waste.

People and prerequisites: Maintainers, stores staff, cleaners and the waste contractor may be affected. The supervisor controls access; a competent chemical adviser and authorised waste route must be available. The cleaning task requires known residues and an approved isolation and cleaning method.

Before: Stop the dependent cleaning step, leave the container closed and restrict access as the local procedure requires. Establish identity using traceable stock, batch and supplier records. Do not open, sniff, sample or move it unless a competent plan makes that action safe.

During: The responsible specialist checks container condition, identity evidence, residue and waste compatibility, and specifies any handling needed. Brief the contractor on the verified hazards and route. If identity cannot be established, manage it through a specialist unknown-material route.

Hold or stop: No mixing, decanting, drain disposal or restart while identity is unresolved. Bulging, heat, leakage, fumes or anyone becoming unwell triggers withdrawal and the local emergency response; do not approach to investigate. The supervisor releases work only after competent confirmation of the revised method.

Completion and hand back: After approved handling or removal, confirm the system, store and waste arrangements match the assessment. Update identification and stock information, check for contamination and hand the area back explicitly.

Evidence: Record the discovery, isolation of the affected task, identity evidence or specialist disposal decision, contractor instructions and supervisor hand-back. Investigate why labelling or inventory control failed.

Applied case

A substitute cleaning product is accepted for use but no one reviews its return to the shared collection system.

Test the assumption

Only whether purchasing obtained a discount. This does not establish acceptance. A change can affect downstream routes even when the primary cleaning result appears acceptable.

Evidence before acceptance

Follow the substance through its lifecycle and verify that relevant procedures, identification and role briefings reflect the accepted change.

Test your decision

What is the missing review?

  1. Only whether the label uses similar wording.
  2. Its compatibility and consequences across the cleaning, return and waste pathways.
  3. Only whether purchasing obtained a discount.
Compare the explanation

Its compatibility and consequences across the cleaning, return and waste pathways.

A change can affect downstream routes even when the primary cleaning result appears acceptable.

Open this interactive lesson →

LESSON 10

Verify the barrier and the receiving role

Verify the barrier and the receiving role.

2D teaching diagram: Pipeline receipt is a two-ended operation
Existing SHAREhub 2D teaching schematic. Use alongside the explanation and fictional case in this lesson.

Understand the mechanism and the decision

A control can involve equipment, information and a human decision, but its purpose should be clear. Identity checks prevent wrong-material acceptance; segregation prevents contact; containment limits release. One record does not establish that all these functions are healthy.

Ask what each barrier must achieve, who maintains it and how a failure becomes visible. A checklist should retain an unconfirmed result when the evidence is missing. Turning an unknown into a tick to avoid delaying a delivery weakens the decision system.

Verify the control in the actual task

Require a factual account of the discrepancy, the responsible review and the verification needed before release; keep the learner exercise separate from an actual approval.

What barriers should control dangerous substance scenarios?

Barriers should prevent release, detect abnormal conditions, control escalation, mitigate consequences and support emergency response.

Barrier thinking is useful because it stops the assessment ending at a label or risk rating. For each credible scenario, the organisation should know which barriers are relied on, who owns them, what performance is required, how they degrade, how they are tested and what happens if they are unavailable.

A barrier may be physical, instrumented, procedural, organisational or emergency-response based. Engineered and independent barriers are usually stronger than controls that require perfect human action under pressure.

Barrier examples
Barrier type Examples Assurance evidence
Prevention Substitution, closed systems, compatible materials, inventory limits and segregation. Design review, SDS review, inspections and procurement controls.
Detection Gas detection, level alarms, pressure alarms, leak detection and operator rounds. Calibration, proof testing, alarm response checks and defect records.
Control Ventilation, inerting, earthing, bonding, temperature control and emergency isolation. Inspection, maintenance, function tests and operating limits.
Mitigation Bunds, relief systems, explosion venting, fire protection and drainage isolation. Design basis, inspection, test records and emergency drill findings.
Emergency response Spill response, evacuation, decontamination, firefighting and liaison with responders. Plans, training, exercises, equipment checks and post-exercise learning.

Applied case

The delivery checklist is signed, but the receiver confirms that the identity discrepancy was never resolved.

Test the assumption

The signature makes all earlier discrepancies irrelevant. This does not establish acceptance. Completion of a record cannot supply missing evidence.

Evidence before acceptance

Require a factual account of the discrepancy, the responsible review and the verification needed before release; keep the learner exercise separate from an actual approval.

Test your decision

Which conclusion is justified?

  1. The relevant material-acceptance hold remains unresolved despite the signature.
  2. The signature makes all earlier discrepancies irrelevant.
  3. The delivery can be released because the form is complete.
Compare the explanation

The relevant material-acceptance hold remains unresolved despite the signature.

Completion of a record cannot supply missing evidence.

Open this interactive lesson →

LESSON 11

Use the planned response to an unexpected mixture

Use the planned response to an unexpected mixture.

2D teaching diagram: Verify the compartment and both transfer paths
Existing SHAREhub 2D teaching schematic. Use alongside the explanation and fictional case in this lesson.

Understand the mechanism and the decision

Unexpected heating, gas, pressure, odour or a release during mixing can indicate a dangerous condition. These observations do not identify a universally safe corrective action. Approaching, opening, moving or adding another substance may increase exposure or reaction.

Raise the alarm and follow the established emergency arrangement from a safe position. Provide factual information about the materials and location to the responsible responders. Do not improvise neutralisation, dilution or rescue on the basis of an awareness lesson.

Verify the control in the actual task

Know the reporting and protective route in advance. Re-entry or recovery requires the authorised assessment of the changed condition, not simply the disappearance of an obvious symptom.

What if incompatible chemicals are mixed?

Stop the task, move people away and activate the site emergency plan; do not approach a reacting container or improvise a neutraliser.

Heat, pressure, hissing, gas, bubbling, bulging, new odour or unexpected colour are stop-and-evacuate cues. Call 999 when there is a suspected toxic release, fire, explosion, serious injury or threat beyond local control. Trained responders need substance identity, SDS, inventory, drainage and site plan. Shut off remotely only where the procedure makes that safe. Untrained staff must not enter a plume, move a bulging container, pour another chemical into it or clean up before the incident is made safe. Reopen only after competent investigation and barrier repair.

On a small screen, scroll this table sideways to read all columns.

Inadvertent-mixing response
SignalImmediate owner/actionRestart gate
Wrong connection before flowOperator holds transfer; supervisor confirms identity and route.Independent route recheck.
Unexpected heat, gas or pressureStop remotely if safe, evacuate and call emergency services.Specialist declares scene safe.
Waste or drain reactionIsolate people and drain route if safe; notify environmental responder.Waste characterization and drain control corrected.

Applied case

A collection vessel begins releasing unexpected vapour after materials were combined; the composition is uncertain.

Test the assumption

Open the vessel to release pressure manually. This does not establish acceptance. The hazard and response need the planned competent emergency arrangements.

Evidence before acceptance

Know the reporting and protective route in advance. Re-entry or recovery requires the authorised assessment of the changed condition, not simply the disappearance of an obvious symptom.

Test your decision

What response is appropriate for an ordinary worker?

  1. Open the vessel to release pressure manually.
  2. Add a familiar chemical to cancel the reaction.
  3. Use the site alarm and protective response without approaching or adding a corrective substance.
Compare the explanation

Use the site alarm and protective response without approaching or adding a corrective substance.

The hazard and response need the planned competent emergency arrangements.

Open this interactive lesson →

LESSON 12

Make the combined material-readiness decision

Make the combined material-readiness decision.

2D teaching diagram: Verify the compartment and both transfer paths
Existing SHAREhub 2D teaching schematic. Use alongside the explanation and fictional case in this lesson.

Understand the mechanism and the decision

The receiving decision combines identity, property information, connection control, segregation and a credible abnormal response. Some parts of a case can be satisfactory while a critical uncertainty remains. A neat store and complete delivery forms do not demonstrate a safe material pathway.

In this case, the product description has changed, the cleaning return is not covered by the acceptance evidence and waste identity is unresolved. Treat each missing fact explicitly and identify the responsible review. The task must not be used as an experiment to find out whether materials can meet safely.

Verify the control in the actual task

Record the actual accepted boundary, remaining restrictions and verification to be handed over; do not turn a course completion into authority to approve the chemical process.

When should work stop and how should an incident be handled?

Stop the affected work if identity, compatibility or a required safeguard is uncertain or if conditions leave the approved method. For a release, fire, abnormal heat, pressure or illness, withdraw, warn others and activate the local emergency arrangements.

Do not investigate an unknown atmosphere, enter a confined area to rescue someone, touch a leaking container or improvise neutralisation. Only trained, equipped and authorised responders should carry out the response defined for that hazard. Operate remote isolation only when the procedure permits it from a safe position; do not approach the release to close a valve.

Call emergency services where the situation requires them and provide the known substance identity, location and hazards from a safe place. Use the product-specific emergency information and trained first-aid arrangements. Keep responders informed about missing identity information. Re-entry, clean-up and restart need competent confirmation that the hazard and damaged controls have been addressed.

Repeated small leaks, missing labels, blocked extraction, dust build-up, disabled alarms or recurring PPE contamination are reasons to investigate the system. Record the event and corrective action; the responsible person must also assess any statutory reporting duty under the applicable GB or NI rules.

Applied case

The shift is ready to receive the changed delivery while the return-route and waste discrepancies remain open.

Test the assumption

Release everything because the delivery driver is waiting. This does not establish acceptance. Time pressure and partial evidence cannot close the unresolved compatibility pathway.

Evidence before acceptance

Record the actual accepted boundary, remaining restrictions and verification to be handed over; do not turn a course completion into authority to approve the chemical process.

Test your decision

What is the defensible task decision?

  1. Accept the known containers and combine the unknown waste later without review.
  2. Hold the affected acceptance and transfers until the connected uncertainties and controls are resolved.
  3. Release everything because the delivery driver is waiting.
Compare the explanation

Hold the affected acceptance and transfers until the connected uncertainties and controls are resolved.

Time pressure and partial evidence cannot close the unresolved compatibility pathway.

Open this interactive lesson →