Focused awareness learning based on SHAREhub pages. Apply the actual workplace arrangements and your role; completion is not practical competence or permission for specialist work.
This reader supplies the complete teaching. Use the interactive LMS course for assessed activities, saved progress and completion.
LESSON 1
Examine the task system
Understand job, individual and organisational influences.
Existing SHAREhub photographic illustration. The written fictional case supplies the condition and decision evidence.
Examine the task system
Human factors means designing work around how people actually think, see, move, remember, communicate and make decisions. HSE describes performance through job, individual and organisation factors. Human factors are a design and management question; they are not simply an assessment of whether the worker was careful. HSE HSG48 reducing error and influencing behaviour HSE human failure types HSE HSG48 full guide A traditional response to an incident might say 'the operator made a mistake'. A human factors response asks better questions: Was the display confusing? Was the alarm flood overwhelming? Was the procedure usable? Was the person fatigued? Was supervision available? Were priorities clear? Had the task changed? Did the organisation reward speed over control?
Applied case
Fictional case: A wrong selection is described as carelessness. The task also involves similar labels, interruptions and unclear supervision, but none of those conditions has been examined.
Action and conditions
What someone did belongs in the sequence. Understanding why requires examination of information, demands and arrangements, rather than assuming either blame or complete innocence.
Test your decision
What should review consider?
A certainty that every error is unavoidable.
The action and relevant task, person and organisational conditions.
The person’s last action treated as a complete causal explanation.
Compare the explanation
The action and relevant task, person and organisational conditions.
Human factors asks how performance is shaped, using evidence.
Photorealistic illustrative UK workplace scene. Review checks: Repeated same error: The system may contain a predictable error trap. Workarounds are normal: People may be adapting to impractical work. Procedures ignored: Procedure may be wrong, unusable or unsupported.
Distinguish different performance problems
Human failure should be analysed by type because different failures need different controls. A slip is an action error, such as pressing the wrong button. A lapse is a memory error, such as forgetting a step. A mistake is a planning or judgement error, such as choosing the wrong isolation method. A violation is a deliberate rule deviation, but even violations often have system causes such as time pressure, poor rules, weak supervision or normalised shortcuts. HSE HSG48 full guide Good investigations use the type of failure to choose controls. A memory lapse may need a checklist or prompt. A mistake may need better training, procedure or decision aid. A violation may need leadership, supervision, rule quality and workload review.
Applied case
Fictional case: A worker intends to follow the method but selects the wrong similar-looking control. An initial report calls this a deliberate rule breach without further evidence.
Different causes need different responses
An unintended selection and a deliberate deviation are not automatically the same problem. Investigate the evidence before choosing an action intended to prevent recurrence.
Test your decision
What is sound?
Examine the action and context before assigning an error or violation explanation.
Assume intent from the outcome alone.
Declare that rule deviations never occur.
Compare the explanation
Examine the action and context before assigning an error or violation explanation.
The type and context matter to an effective response.
Consider design and physical safeguards before reminders.
Existing SHAREhub 2D teaching schematic. Use alongside the explanation and fictional case in this lesson.
Reduce the opportunity for error
Good job design makes the safe way practical, obvious and achievable. A job that requires high force, awkward posture, fine judgement, memory of many steps, poor access, conflicting instructions and rushed timing is an error trap. People will work around it because they still have to get the job done. Human factors turns those traps into design questions. HSE HSG48 full guide Design improvements can be small: better lighting, clearer labels, valve numbering, task sequencing, lifting aids, interlock design, less cluttered screens, better access to isolation points, clearer procedures or fewer interruptions during safety-critical steps. ERICPD is used here as a planning mnemonic. The linked HSE five-level hierarchy is the official source for the order and relative reliability of controls; the two labels are not identical.
Applied case
Fictional case: Repeated selection mistakes occur at controls with confusing identification. The proposed action asks people to remember harder while leaving the same decision arrangement unchanged.
Make success achievable
Training can support a usable task. It cannot automatically overcome a confusing interface or replace a protective function that should prevent a credible error reaching harm.
Test your decision
What should be reviewed?
Repeat the existing reminder without reviewing the confusing selection arrangement.
A claim that experienced people cannot err.
Whether identification, task design and suitable safeguards can reduce the error pathway.
Compare the explanation
Whether identification, task design and suitable safeguards can reduce the error pathway.
Design can change the conditions that make mistakes likely.
Photorealistic illustrative UK workplace scene. Review checks: Eliminate: Remove the wrong-valve path or unnecessary manual transfer decision by process redesign. Reduce: Use a simpler connection or sequence with fewer similar valve choices. Isolate: Physically segregate wrong lines or lock out the incompatible valve during transfer. Control: Use distinct labels, position feedback, high-level trip and independent stop where justified. Control: Use concise procedure, point-of-use verification and realistic workload/staffing.
Look at competing demands
Both overload and underload can degrade performance. High workload can reduce attention, memory and decision quality. People may miss alarms, skip checks, forget handback steps or rely on shortcuts. Underload can also be dangerous, especially in monitoring roles where boredom and low stimulation reduce situation awareness. HSE HSG48 full guide Workload should be assessed during normal work, peaks, abnormal operations, emergencies, turnarounds, maintenance shutdowns, lone working and organisational change. Staffing is not just headcount; it is whether the right people with the right competence are available at the right time. Organisational factors create the climate in which people decide what really matters. Leadership messages are not only speeches. They are budgets, staffing levels, maintenance deferrals, contractor choices, action close-out, overtime expectations, response to bad news and whether supervisors are supported when they stop work.
Applied case
Fictional case: Two time-critical tasks regularly coincide. The supervisor assumes the unchanged headcount proves the work is manageable, but actual timing and support have not been reviewed.
One task and two tasks
A task may be manageable alone yet conflict with another demand. Examine timing, complexity and support before relying on greater effort as the solution.
Test your decision
What information is needed?
A diagnosis based on the brief case.
The concurrent demands, task requirements and available support.
The unchanged staffing total without examining concurrent critical demands.
Compare the explanation
The concurrent demands, task requirements and available support.
Workload needs task evidence rather than assumption.
Existing SHAREhub photographic illustration. The written fictional case supplies the condition and decision evidence.
Use information that supports decisions
Procedures should help competent people do the right thing under real conditions. A good procedure is accurate, current, short enough for the task, written for the user, tested with workers and linked to competence. It highlights safety-critical steps, decision points, hold points, warnings and stop-work triggers. It should not be a legal shield written in language nobody uses. HSE HSG48 full guide Procedures are weaker where the task is fast-moving, highly physical, abnormal, time pressured or dependent on equipment condition. In those cases, the procedure needs support from engineering controls, supervision, checklists, labelling, prompts and competent planning. Communication is a control when people need shared understanding at the right time. Safety-critical communication includes briefings, handovers, permits, radio calls, alarms, warning signs, procedures, shift logs, contractor instructions and emergency messages.
Applied case
Fictional case: The current instruction describes equipment clearly on paper, but users cannot read the relevant identifier from the stated working position and have begun relying on memory.
Written and usable
A document may be current yet difficult to apply. User experience and task observation can reveal where the information fails to support the required decision.
Test your decision
What should happen?
Review the actual usability and control the mismatch through the responsible route.
Tell users to guess the familiar item.
Treat the document revision as proof of usability.
Compare the explanation
Review the actual usability and control the mismatch through the responsible route.
Current information must work at its point of use.
Choose assurance related to the identified weakness.
Photorealistic illustrative UK workplace scene. Review checks: Task analysis: The process safety team identifies safety-critical tasks such as tanker overfill prevention, valve lineup, hot work permit issue, drain isolation and alarm response. Work design: Tasks are reviewed for access, visibility, labelling, workload, time pressure, handover and procedure usability. Competence: Operators, permit issuers, supervisors and contractors have role-specific competence standards and reassessment intervals.
Test whether the improvement worked
Evidence should show that tasks, people and organisational conditions are understood and improved. Human factors evidence is not just a culture survey. Strong evidence comes from task observations, procedure reviews, workload assessments, staffing reviews, competence records, communications checks, incident investigations, audit findings, worker feedback and management review decisions. HSE HSG48 full guide The best evidence compares work as imagined with work as done. If a procedure says two people verify an isolation but field observation shows one person is always pulled away, the human factors issue is resource and work design, not just non-compliance. For wrong-valve opening during tank transfer under workload and label ambiguity, the management check should start with a real control decision: Remove the wrong-valve path or unnecessary manual transfer decision by process redesign.
Applied case
Fictional case: A reviewed control change is installed after repeated selection errors. The action closes on delivery records, while its practical effect on the actual selection task is unexamined.
A fair and useful review
Recognise demonstrated improvement within its scope. Retain unresolved questions and examine context, while leaving actual role authorisation and specialist decisions to the appropriate arrangements.
Test your decision
What is missing?
The change’s installation date without checking the selection task afterwards.
Proof that all future human error is impossible.
Evidence that the changed arrangement reduces the identified task weakness.
Compare the explanation
Evidence that the changed arrangement reduces the identified task weakness.
Effectiveness should relate to the original mechanism.