Safe access, gardens and deliveries

Free online training · Approximate learning time: 110–180 minutes · Self-paced

Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.

Lesson 1

A safe route must still be a usable route

Apply a safe route must still be a usable route to the current person and task.

Separated pedestrian walkway and parked forklift in a UK yard. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Receive and unload identified palletised packaged goods from a rigid lorry using a suitable counterbalance forklift. Act: The supervisor checks the bay surface, lighting, pedestrian barriers, clear route and local unloading plan. Hold / review: Hold an unbooked vehicle, changed vehicle type, unknown load mass, damaged pallet or shifted load for the supervisor and, when needed, supplier or competent specialist.

A safe route must still be a usable route

A garden, entrance or driveway is part of a resident’s daily life. Assess the journey from the person’s starting point to the place they want to reach, including the return journey. A route that technically exists but is too narrow for a wheelchair, too steep for the agreed assistance or unavailable at the time of use is not an effective alternative. Ask what the person wants to do and what support works for them; do not infer this from their age or diagnosis.

Vehicles, paving, lighting and weather interact. A delivery parked beside a repaired path can remove its usable width. Glare may hide an entrance edge that was clear at midday. Meltwater may refreeze after the winter-treatment record has been signed. Inspect when the activity actually happens and use observations alongside the transport plan and individual support arrangements. A warning cone or reversing alarm can communicate a problem, but it does not remove the conflict.

In the fictional exercise, ask the person whether the proposed alternative supports the visit they want, including rest points, mobility equipment and the assistance actually available. Do not choose a route solely because a staff member can walk it. The support team and premises team may need different information: one understands the person's needs and consent, while the other assesses the route and physical correction. Neither should assume the other's check has been completed.

When access is temporarily unavailable, describe the specific affected journey and provide suitable support through the actual plan. Avoid turning a temporary defect into a blanket prohibition on the garden. A resident's preferences are relevant evidence, while their diagnosis alone does not settle a decision. Record the agreed interim arrangement, who will review it and what restores normal access. Keep all course cases fictional and omit identifying resident information from public exercises.

How do you design safer routes and choose controls?

Map actual movements, remove unnecessary vehicle–pedestrian contact, then protect unavoidable interfaces. Physical separation and suitable layout come before signs, high-visibility clothing and expectations that people will always react correctly.

Observe the site at busy and quiet times. Draw staff routes to toilets, welfare and exits alongside forklifts, lorries, customer cars, waste collections and emergency access. Include a pedestrian’s natural walking route, not just the route drawn on the plan. A long detour that encourages shortcuts needs redesign, not repeated reminders. See HSE workplace transport risk assessment for the relevant source and scope.

  1. Remove or reduce the movement: relocate a collection point, use drive-through arrangements or keep deliveries outside public access periods where practicable.
  2. Separate by design: provide suitable pedestrian routes, barriers, separate doors and protected waiting areas. Select barriers for the foreseeable impact; a painted line is not a crash barrier.
  3. Control remaining crossings: use visible, accessible crossing points away from reversing areas, suitable lighting, clear priority and enough visibility and stopping distance.
  4. Support the design: brief routes, control access and delivery timing, supervise and enforce locally assessed speed limits. Select task-appropriate protective equipment for residual risks.

Routes must suit the largest vehicle and load that will actually use them, including turns, slopes, headroom and ground-bearing capacity. Keep surfaces drained and clear; protect vulnerable racking, fuel equipment and edges. Temporary routes need the same risk-based scrutiny. HSE HSG136 third edition (pages 9–13) provides the design principles.

There is no single safe speed, lane width or pedestrian clearance for every yard. The vehicle, load, bends, visibility, surface and users determine the decision. A posted limit is a maximum within the local system, not permission to drive at that speed when conditions are worse. HSE site speed limits describes choosing and enforcing site limits.

Applied case

At dusk, a resident’s usual level route is icy. The only suggested alternative includes steps and a parked van.

Decision and explanation

A genuinely usable protected route and the assessed assistance for this person.

An alternative needs to work for the person, equipment, assistance and current conditions, not merely exist on paper.

Lesson 2

Turn a defect report into a verified improvement

Apply turn a defect report into a verified improvement to the current person and task.

Maintaining temporary roof-edge protection — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Turn a defect report into a verified improvement

Describe the exact place, time and conditions rather than writing “garden unsafe”. Record who may be affected and how: a front wheel catching a raised slab, a person remaining in a driver’s blind spot or a level approach becoming icy. Protect the affected movement first through the agreed arrangements; never put yourself in a vehicle’s path to make it stop. Give the duty manager a clear account of the immediate restriction and the access residents still need.

The premises and care teams must coordinate the remedy. A completed repair needs a practical check with the relevant mobility aids, sightlines and weather conditions. If a temporary gate restriction is proposed, refer it through the person-specific consent and lawful decision process. A maintenance instruction cannot itself authorise a restriction of liberty. Handover should identify the owner, what remains unavailable, how assistance is provided and what triggers a fresh review.

A practical check should be planned so it does not expose the resident or worker to the defect it is meant to investigate. Inspect the corrected route from safe positions and use the appropriate competent method before asking someone to use it. A wheelchair journey should not be used as a hazardous trial across uncertain paving. Confirm the route's width and support needs through suitable assessment rather than guessing from the model.

Close-out also includes communication. Reception, delivery staff and the next shift need to know the waiting point, available entrance and any remaining restriction. A contractor's completed job may leave equipment or barriers that affect access. Ask the responsible person to verify the whole arrangement and a safe return journey. If weather or use changes, the report should reopen through the actual process instead of remaining closed because its original deadline was met.

How should the selected controls be checked in practice?

ERICPD is used here as a planning mnemonic. The linked HSE five-level hierarchy is the official source for the order and relative reliability of controls; the two labels are not identical.

Start with task redesign and substitution, then engineered separation before procedures and personal protection; verify each control under real conditions.

At a fuel depot, tanker overfill can release petrol, form vapour and ignite. The assessment must identify the initiating event, people exposed and each independent prevention or mitigation barrier. Petrol cannot be substituted if the site must supply it, so the record should say why that higher-order option is unavailable for this operation and then demand strong engineered controls. HSE hierarchy of control; HSE hierarchy of control.

ERICPD is a six-stage planning aid; the HSE five-level order separates substitution, engineering and administration. Isolate is usually engineered separation, while ERICPD Control may contain both physical and administrative measures. Discipline sustains the chosen controls and is not an additional permission to expose people.

Choose an activity to compare its ERICPD and ISO 45001 controls.

Applied case

The contractor reports the slab repaired, but the replacement route has not been tried with the wheelchair used there.

Decision and explanation

A practical check of the completed route with the relevant access and assistance needs.

The record of work is useful, but the outcome must be checked against the access problem that prompted it.

Lesson 3

Separate a late delivery from a resident journey

Choose a protected waiting and movement arrangement.

Separated pedestrian walkway and parked forklift in a UK yard. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Receive and unload identified palletised packaged goods from a rigid lorry using a suitable counterbalance forklift. Act: The supervisor checks the bay surface, lighting, pedestrian barriers, clear route and local unloading plan. Hold / review: Hold an unbooked vehicle, changed vehicle type, unknown load mass, damaged pallet or shifted load for the supervisor and, when needed, supplier or competent specialist.

Separate a late delivery from a resident journey

A late arrival can coincide with a resident's ordinary use of the entrance. The driver may concentrate on unloading while a person using a mobility aid needs more time and space to cross the same area. A reversing alarm informs people but does not stop someone entering the path. Treat the full vehicle, load and pedestrian envelope as relevant rather than checking only the cab's position.

Prefer arrangements that separate the activities, such as an appropriate delivery schedule, suitable waiting point and continuous protected walking route. The actual design must suit the vehicle and the people using the home. Do not move a resident's journey into steps or an unsuitable narrow gap merely to keep a delivery moving. Reception and care staff should coordinate the person's wishes and support with the premises movement plan.

If the delivery conflicts with the protected route, hold the movement safely through the agreed system and obtain the responsible coordinator's decision. A worker must not stand behind a reversing vehicle to block it or improvise as a signaller without the required training and method. Ask the driver to explain where they wait and what stops the movement; familiar visits do not establish understanding of a changed arrangement.

Verify the route through arrival, unloading and departure and include residents returning from an outing. Check temporary storage, darkness and other deliveries. A plan should remain usable during ordinary pressures and allow people to ask for assistance without losing their intended activity. For the fictional exercise, state the current conflict, protective hold and evidence needed for release. No course response authorises a real traffic movement or overrides a resident's lawful care and support arrangements.

When must the movement stop and how can it restart?

Stop the affected operation whenever its safe conditions are lost or cannot be confirmed. Keep people clear, inform the responsible supervisor and restart only after the defect or changed conditions have been assessed, controlled and communicated.

Avoid reversing wherever practicable. Where it remains necessary, provide a designated area, exclusion and suitable visibility controls. A banksman or signaller is a person guiding the driver, not a protective barrier. HSG136 treats this as a last-resort measure after other ways to control reversing risk; some vehicle and industry settings make it unsuitable. If used, the trained signaller needs an agreed signal system, a safe position and continuous visibility to the driver. If the driver loses sight of the signaller, stop immediately. HSE safe reversing. See HSE workplace transport risk assessment for the relevant source and scope.

TriggerImmediate actionRestart evidence
Person in an operating or reversing zoneStop vehicle and load movement safely. Keep other traffic out.Supervisor confirms the person is clear and effective segregation and access control are restored. (HSE)
Lost signaller, obscured route or failed visibility aidStop the affected manoeuvre; do not continue by guesswork.Visibility, agreed communication and all controls required by the assessed method are re-established. (HSE)
Brake, steering, restraint or other safety defectTake the affected operation out of use and report the defect.Competent repair and verification, or a separately assessed recovery method; no informal bypass. (HSE)
Unknown load, incompatible vehicle or changed routeHold in a safe place and contact the host, carrier or supplier.Identity and suitability confirmed; revised plan approved by the responsible competent people and briefed. (HSE)
Ice, spill, failed light, damaged barrier or unsafe surfaceClose the affected route or bay and protect people.Defect corrected and inspected, or an assessed and protected alternative route put into use. (HSE)

Collision, trapped person, fire or leak: stop surrounding traffic without entering its path, raise the alarm and call the local emergency response and 999 where needed. Keep clear of unstable vehicles, loads, fuel and electrical hazards. Do not attempt improvised lifting or vehicle movement to free a person; emergency responders and the site rescue arrangements must control that decision. Provide first aid only when it is safe and within competence. Preserve relevant evidence after immediate protection and emergency needs are met.

Report damage and near misses internally so the underlying route or system failure can be corrected. The responsible person must separately check whether statutory reporting applies: use HSE incident reporting for GB and HSENI report an incident for Northern Ireland. Their criteria differ; not every near miss is a reportable dangerous occurrence.

Applied case

A delivery reverses across the level garden route just as a resident wants to go outside.

Decision and explanation

A safe hold and genuinely usable separated route with the person’s assessed support.

An alarm does not separate the activities or provide suitable access.

Lesson 4

Weather and lighting change the same route

Use current conditions rather than the last signed inspection.

Inspection of a dry clear walkway and entrance mat in a UK workplace. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Heavy rain carries water and leaves through a public leisure-centre entrance. Act: Close or physically separate the wet route, provide a safe accessible alternative, remove contamination and correct matting/drainage defects. Hold / review: Do not reopen while the hazardous condition remains or the alternative creates another hazard.

Weather and lighting change the same route

An entrance may be usable at midday but difficult at dusk or after a temperature change. Ice, water, glare and shadows can hide an edge or alter traction. A resident may use a walking aid or have sensory needs that change the effect of those conditions. Do not infer every person's ability from one worker walking across the route in daylight.

Plan inspection and maintenance around actual use and foreseeable changes. Winter treatment needs a suitable method, supplies, timing and review when conditions change; a signature earlier in the day is not continuing evidence that ice has gone. Lighting should support the relevant journey without glare or hidden steps, and defects need a usable response. This lesson does not prescribe a universal illuminance, treatment interval or safe surface temperature.

Protect the affected route and arrange an appropriate alternative or assistance through the actual plan. A cone communicates a problem but cannot provide traction or make an inaccessible detour suitable. Do not close every outdoor activity simply because one route needs correction. Coordinate the person's preference, immediate support and premises action, with a specific review condition rather than an indefinite restriction.

Verify the remedy under the relevant conditions by a safe appropriate check. Confirm drainage, lighting and the whole return journey, and communicate any continuing restriction to the next shift. For the exercise, compare the current icy surface with the historical treatment record and explain which governs the immediate decision. A model picture can locate a hazard but cannot measure friction, light level or the person's individual ability. Factual observations and suitable competent checks must support the real reopening decision.

When should a slip or trip hazard trigger immediate action?

Immediate action is needed when a route is contaminated, obstructed, damaged, poorly lit or exposing people who cannot reasonably avoid the hazard.

Point-of-use source supports the section’s main boundary; check the actual task and location.

Slips and trips are often time-critical. A spill, wet cleaned floor, damaged stair nosing, icy entrance or trailing cable can harm the next person using the route. The first decision is whether to remove, isolate or divert before normal work continues.

Supervisors should be clear that 'reported' is not the same as 'controlled'. If the hazard remains, interim control is needed.

TriggerImmediate actionFollow-up
Spill or wet floorStop access if needed, clean with correct method and leave dry.Find source and prevent recurrence. HSE barriers and cleaning
Trailing cable or hoseRemove, reroute, cover properly or restrict route.Review power/water access and work method. HSE floor suitability
Damaged floor or stairPrevent access to the dangerous area and provide a safe alternative route; marking alone does not control exposure.Repair and record defect close-out. HSE floor suitability
Ice, leaves or mudTreat, clear, reroute or restrict affected path.Review weather plan, drainage and inspection frequency. HSE floor suitability
Poor lightingStop or divert work where hazards cannot be seen.Repair lighting and verify levels. HSE workplace-transport lighting
Repeated incident locationEscalate beyond local housekeeping.Map causes and review design, cleaning and maintenance. Point-of-use source

Warnings and cones communicate a hazard; they do not by themselves prevent access. Use the assessed physical separation and usable alternative route, then verify the surface and access conditions before reopening.

Applied case

The winter sheet is signed but meltwater has refrozen beside an entrance step at dusk.

Decision and explanation

The current condition and a suitable protective response, followed by verification.

Controls need to work when the route is used.

Lesson 5

A gate restriction needs an individual lawful decision

Keep premises safety separate from authority to restrict a person.

Safety professional reviewing guidance and documents in a UK workplace office. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Customers and visitors: Controls slips, access, supervision, emergencies and information. Workers: Manages training, workload, stress, lone work and task risks. Contractors: Checks competence, provides information and monitors work.

A gate restriction needs an individual lawful decision

A gate can help manage a physical interface, but locking it can also prevent a resident doing something they value. A maintenance worker's instruction does not decide consent, capacity or lawful restriction. Nor does one person's incident justify applying the same restriction to everyone. The fictional case asks staff to protect access while referring person-specific decisions through the proper care process.

Ask what the person wants and what support, information or environmental change could enable it. Communicate in a way they can understand and involve the appropriate people under the actual consent and decision-making arrangements. Do not infer inability to decide from age, disability or diagnosis. This awareness course does not teach staff to assess legal capacity or authorise deprivation of liberty; the applicable national law and competent roles must guide those decisions.

Where an immediate hazard exists, use the agreed protective response and escalate promptly. Keep the physical defect, temporary support and proposed restriction as distinct actions. For example, treating ice may restore a route while a locked gate still needs individual review. Consider less restrictive suitable alternatives and a clear timescale or trigger for review through the actual lawful process. Safety cannot be reduced to choosing between an uncontrolled hazard and a permanent ban.

Verification asks whether the route and support work for this person and whether any restriction has the necessary authority and continuing justification. Document factual information respectfully and share only what the relevant roles need. The fictional exercise should identify questions for the care lead rather than invent a resident's capacity finding. A course pass cannot approve a real restriction, and a premises checklist cannot supply consent on somebody else's behalf.

Who may be owed a duty of care?

A duty of care may be owed to workers, contractors, visitors, customers, tenants, service users and members of the public.

Health and safety duties extend beyond direct employees. Section 3 of HSWA covers people not in employment who may be affected by the undertaking. Civil duties may arise through occupiers' liability, negligence, product safety or contractual relationships. The precise route depends on the facts, but the management question is similar: who could be harmed by what we do or fail to do?

Organisations should map groups of people because different groups need different controls. Employees can be trained and supervised; visitors may need signage, barriers, escorting or information; contractors need coordination; customers need safe premises; members of the public need protection from site activities.

People who may be affected - People who may be affected
Group Duty of care issue Example control
Employees and workers Work activities, environment, equipment and health risks. Risk assessment, training and supervision. Sources: Health and Safety at Work etc. Act 1974; Health and Safety at Work (Northern Ireland) Order 1978.
Contractors Site hazards and task hazards interact. Induction, permits and coordination. Sources: Health and Safety at Work etc. Act 1974; Health and Safety at Work (Northern Ireland) Order 1978.
Visitors and customers They may not understand workplace risks. Safe routes, signage and restricted access. Sources: Health and Safety at Work etc. Act 1974; Health and Safety at Work (Northern Ireland) Order 1978.
Remote workers Workstation, workload, communication and isolation risks. DSE assessment and manager contact. Sources: Health and Safety at Work etc. Act 1974; Health and Safety at Work (Northern Ireland) Order 1978.
Vulnerable people Greater susceptibility to harm or different needs. Individual assessment and adjustments. Sources: Health and Safety at Work etc. Act 1974; Health and Safety at Work (Northern Ireland) Order 1978.
Public and neighbours Work activities can affect people outside the site. Traffic, dust, noise, barriers and emergency planning. Sources: Health and Safety at Work etc. Act 1974; Health and Safety at Work (Northern Ireland) Order 1978.

Applied case

A gate is locked for all residents because one resident previously needed support outdoors.

Decision and explanation

An individual proportionate review through the applicable consent and lawful decision process.

Do not substitute a blanket premises rule for person-specific lawful care decisions.

Lesson 6

Handover must preserve the usable alternative

Verify that temporary protection survives the next shift.

Maintaining temporary roof-edge protection — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Handover must preserve the usable alternative

A good temporary route can fail when a van parks in it or a replacement worker does not know which assistance is needed. The handover should therefore describe the actual usable arrangement rather than only the defect. “Garden closed” tells the next shift little about the person's wishes, the immediate support or the condition that will restore access.

In the fictional handover, identify the affected entrance, delivery waiting point, protected alternative and required support. Keep person-specific details within the authorised care record and give premises or drivers only the information relevant to their role. Do not display private resident information on a public traffic notice. The course worksheet uses invented information so learners can practise the distinction without creating a real care record.

Assign responsible roles for the physical repair, access support, lawful restriction review and verification. They may be different people. A contractor finishing a paving job does not automatically close the consent issue, and a care lead agreeing support does not certify the surface. Unconfirmed conditions should remain visible with a protective hold and escalation route. Avoid averaging checklist scores to offset an unresolved critical access problem.

Before closing the issue, check the full corrected journey and communicate it to those affected. Observe ordinary use safely and invite feedback about barriers or shortcuts. Reassess when weather, equipment or the person's needs change. The exercise ends with an evidence-based handover: what is confirmed, what remains held, who acts and what closes it. It should support daily life and safe movement together, rather than forcing residents or staff to improvise around an unresolved delivery or route conflict.

What should a good risk register capture?

A good risk register connects credible scenarios to controls, owners, evidence, actions and review triggers.

Risk registers should not become lists of generic hazards. The best registers are specific enough to support decisions. They show what could happen, what controls are relied on, who owns them, what evidence proves they work and what still needs improvement.

For major accident hazards, the register should connect to barrier registers, safety critical elements, maintenance, inspection, operating limits and emergency planning.

FieldWhy it mattersExample
ScenarioShows the chain of harm.Flammable vapour release during tanker unloading ignites at nearby vehicle.
People/assets affectedClarifies consequence and dutyholder scope.Drivers, operators, neighbours, environment and site assets.
Existing controlsShows what is relied on now.Earthing, overfill prevention, exclusion zone, permit and supervision.
Control evidenceSeparates paper controls from live controls.Inspection, calibration, drill, observation and training records.
Further actionCaptures what still needs improvement.Install barrier, update procedure, train team and verify.
Review triggerKeeps assessment alive.Incident, change, audit finding, new substance or new equipment.

Applied case

A night shift receives only “path repaired”, but temporary barriers still block wheelchair access.

Decision and explanation

The complete usable route, support, remaining restrictions and verification owner.

A completed repair may leave the journey unavailable.

Lesson 7

Keep deliveries separate from everyday resident movement

Use the same separation test for refuse collection, ambulance arrivals and maintenance vehicles; involve the people who use the route.

Separated pedestrian walkway and parked forklift in a UK yard. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Setting: Receive and unload identified palletised packaged goods from a rigid lorry using a suitable counterbalance forklift. Act: The supervisor checks the bay surface, lighting, pedestrian barriers, clear route and local unloading plan. Hold / review: Hold an unbooked vehicle, changed vehicle type, unknown load mass, damaged pallet or shifted load for the supervisor and, when needed, supplier or competent specialist.

Understand the activity and how harm develops

The garden route is part of someone’s home, so a delivery timetable cannot assume that everyone will see a reversing van, hear a warning or step aside quickly. A person using a wheelchair or walking aid may need more space and time, while a driver’s mirrors still leave blind areas.

Trace the whole journey from the vehicle gate to the unloading point. Prefer arrangements that remove reversing and keep the resident route physically separate. If a crossing remains, the home and delivery company need an agreed way to hold vehicle movement until people are clear; a reversing alarm alone cannot provide that separation.

Recognise the evidence boundary

QuestionCase evidence
What is observed?A delivery van reverses across the route from the entrance to the garden.
How can harm occur?Residents, visitors or staff can be struck or crushed by the vehicle.
What information is needed?Check pedestrian movements, delivery timing, sightlines and the transport plan.

Protect, manage and verify

PurposePractical application
Immediate protectionSeparate deliveries from resident access using a workable protected route and supervised arrangements.
Accountable work arrangementDuty manager and transport coordinator, working with the delivery company. The vehicle and resident route cannot be kept apart, or the driver cannot confirm the route is clear.
Release verificationObserve the revised movement plan with actual access and assistance needs.

Apply this at work

Use the same separation test for refuse collection, ambulance arrivals and maintenance vehicles; involve the people who use the route.

How do you design safer routes and choose controls?

Map actual movements, remove unnecessary vehicle–pedestrian contact, then protect unavoidable interfaces. Physical separation and suitable layout come before signs, high-visibility clothing and expectations that people will always react correctly.

Observe the site at busy and quiet times. Draw staff routes to toilets, welfare and exits alongside forklifts, lorries, customer cars, waste collections and emergency access. Include a pedestrian’s natural walking route, not just the route drawn on the plan. A long detour that encourages shortcuts needs redesign, not repeated reminders. See HSE workplace transport risk assessment for the relevant source and scope.

  1. Remove or reduce the movement: relocate a collection point, use drive-through arrangements or keep deliveries outside public access periods where practicable.
  2. Separate by design: provide suitable pedestrian routes, barriers, separate doors and protected waiting areas. Select barriers for the foreseeable impact; a painted line is not a crash barrier.
  3. Control remaining crossings: use visible, accessible crossing points away from reversing areas, suitable lighting, clear priority and enough visibility and stopping distance.
  4. Support the design: brief routes, control access and delivery timing, supervise and enforce locally assessed speed limits. Select task-appropriate protective equipment for residual risks.

Routes must suit the largest vehicle and load that will actually use them, including turns, slopes, headroom and ground-bearing capacity. Keep surfaces drained and clear; protect vulnerable racking, fuel equipment and edges. Temporary routes need the same risk-based scrutiny. HSE HSG136 third edition (pages 9–13) provides the design principles.

There is no single safe speed, lane width or pedestrian clearance for every yard. The vehicle, load, bends, visibility, surface and users determine the decision. A posted limit is a maximum within the local system, not permission to drive at that speed when conditions are worse. HSE site speed limits describes choosing and enforcing site limits.

Applied case

A late van arrives while a resident and carer are halfway to the garden. The driver gestures that they can squeeze behind it.

Decision and explanation

Hold the van and keep the resident on a protected route.

Mobility and reaction time cannot be assumed; the person remains in the reversing path. An alarm warns but does not prevent contact in a blind area. Stopping vehicle movement creates separation while staff arrange a suitable crossing.

Lesson 8

Repair the route while preserving garden access

Assess external routes as part of daily living. A completed maintenance ticket should lead to a practical access check.

Slips and Trips — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Teaching graphic from the linked SHAREhub source section.

Understand the activity and how harm develops

A small raised paving edge can catch the foot of someone who shuffles, the front wheel of a wheelchair or the tip of a walking frame. The consequence may be much greater than the size of the defect suggests, particularly for a person with fragile bones or difficulty recovering balance.

Look beyond the single slab to drainage, roots, settlement, lighting and the route to seating. A cone is a warning, and may itself narrow the path. The temporary arrangement should give residents a usable way into the garden while a competent repair removes the change in level.

Recognise the evidence boundary

QuestionCase evidence
What is observed?A lifted paving edge lies beside a garden chair and walking route.
How can harm occur?A trip can cause a fall, particularly where balance or mobility is reduced.
What information is needed?Inspect the route and ask residents about their usual access and support needs.

Protect, manage and verify

PurposePractical application
Immediate protectionProvide an accessible alternative and arrange repair without excluding garden use unnecessarily.
Accountable work arrangementPremises lead with care staff who understand residents’ access needs. The defective surface cannot be avoided by a route the person can actually use.
Release verificationCheck the repaired route is stable and usable with relevant mobility aids.

Apply this at work

Assess external routes as part of daily living. A completed maintenance ticket should lead to a practical access check.

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

Control classification: Classify the mechanism separately from its upkeep: physical floor repair, drainage, barriers, protected routes, compartmentation, fire doors and suitable disposal facilities are physical measures where specified. Cleaning schedules, inspections, policies, funding, supervision and verification are administrative arrangements maintaining them. A verbal instruction is not a physical barrier. Read this correction with the source table. Retained overview and stage artwork requires the matching classification update.

Remove or reduce the hazard before relying on procedures or personal protection.

For slips and trips, assess the actual task and first look for a way to remove the hazard. Where that is not possible, consider a safer substitute, engineered separation and then clear work procedures. PPE protects against remaining exposure; it does not make an uncontrolled task safe. HSE hierarchy of controls

The selected measures need a named owner, a usable stop point and a check that they still work when the task or conditions change. In Northern Ireland, verify the separate legal route and site instructions.

For the wet entrance, eliminate recurring water entry at source where practicable. Reduce contamination with suitable matting, drainage and a cleaning method that leaves the route safe; physically prevent access while unsafe and provide an alternative. Repair floor and route defects, then select footwear for residual risk and sustain checks. ERICPD (Eliminate, Reduce, Isolate, Control, PPE, Discipline) is a teaching prompt; Discipline means competent cleaning, supervision and defect closure. HSE slip and trip factors; HSE barriers and cleaning.

How can the ERICPD hierarchy of controls remove slip and trip hazards from workplace routes?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ERICPD control levelTopic-specific exampleSource and full task context
Eliminate

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Reduce

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Isolate

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Control

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Discipline

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ESEAP mapping crosswalk: these are retained ERICPD source rows, mapped to the five ESEAP levels. Read the control-classification correction for mixed physical and administrative measures; six source rows do not mean six ESEAP levels.
Five-level control stage(s)Topic-specific exampleSource and full task context
Elimination

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Administrative controls

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

Applied case

A cone has been left beside the raised slab, but the only gap is too narrow for a resident’s wheelchair.

Decision and explanation

Provide a usable alternative and verify the completed repair.

Access remains meaningful only if the person and their equipment can actually use it. That introduces unsafe handling and leaves the defect uncontrolled. An avoidable blanket restriction overlooks proportionate repair and accessible alternatives.

Lesson 9

Make entrance level changes visible in real conditions

Check places when they are hardest to use: dusk, wet weather and transitions between bright and dark areas.

Slips and Trips — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Teaching graphic from the linked SHAREhub source section.

Understand the activity and how harm develops

The entrance step can disappear visually when light is poor, its edge has little contrast or a bright lobby makes the outside look dark. A resident with reduced vision may need time to adapt between spaces. Glare and shadows can conceal a level change even when a light fitting is switched on.

Inspect the approach at dusk and from the direction people actually travel. Assess the level access option, edge definition and lighting together. Assistance may be needed for an individual, but repeated dependence on staff to point out an invisible step signals a premises problem that should be corrected.

Recognise the evidence boundary

QuestionCase evidence
What is observed?A dark step blends into the entrance surface at dusk.
How can harm occur?A person may misjudge the change in level and fall.
What information is needed?Review lighting and contrast in the conditions when people actually use the entrance.

Protect, manage and verify

PurposePractical application
Immediate protectionRestore suitable illumination and an assessed accessible approach.
Accountable work arrangementPremises lead and care team; seek suitable access or visual-needs advice when required. The approach is too dark or visually confusing for the intended person to use safely.
Release verificationCheck visibility and route usability at the relevant time of day.

Apply this at work

Check places when they are hardest to use: dusk, wet weather and transitions between bright and dark areas.

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

Control classification: Classify the mechanism separately from its upkeep: physical floor repair, drainage, barriers, protected routes, compartmentation, fire doors and suitable disposal facilities are physical measures where specified. Cleaning schedules, inspections, policies, funding, supervision and verification are administrative arrangements maintaining them. A verbal instruction is not a physical barrier. Read this correction with the source table. Retained overview and stage artwork requires the matching classification update.

Remove or reduce the hazard before relying on procedures or personal protection.

For slips and trips, assess the actual task and first look for a way to remove the hazard. Where that is not possible, consider a safer substitute, engineered separation and then clear work procedures. PPE protects against remaining exposure; it does not make an uncontrolled task safe. HSE hierarchy of controls

The selected measures need a named owner, a usable stop point and a check that they still work when the task or conditions change. In Northern Ireland, verify the separate legal route and site instructions.

For the wet entrance, eliminate recurring water entry at source where practicable. Reduce contamination with suitable matting, drainage and a cleaning method that leaves the route safe; physically prevent access while unsafe and provide an alternative. Repair floor and route defects, then select footwear for residual risk and sustain checks. ERICPD (Eliminate, Reduce, Isolate, Control, PPE, Discipline) is a teaching prompt; Discipline means competent cleaning, supervision and defect closure. HSE slip and trip factors; HSE barriers and cleaning.

How can the ERICPD hierarchy of controls remove slip and trip hazards from workplace routes?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ERICPD control levelTopic-specific exampleSource and full task context
Eliminate

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Reduce

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Isolate

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Control

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Discipline

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ESEAP mapping crosswalk: these are retained ERICPD source rows, mapped to the five ESEAP levels. Read the control-classification correction for mixed physical and administrative measures; six source rows do not mean six ESEAP levels.
Five-level control stage(s)Topic-specific exampleSource and full task context
Elimination

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Administrative controls

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

Applied case

The entrance passes a midday inspection, but a resident reports being unable to see the step on their evening return.

Decision and explanation

Inspect at dusk and verify lighting, contrast and accessible access.

Attention cannot compensate for an inadequately visible change in level. The report concerns a particular condition; the verification must reproduce it safely. A functioning bulb does not establish that the step is visible.

Lesson 10

Winter access needs an effective treatment and a usable route

Make winter plans a cycle of forecast, action, inspection and reassessment, with access needs included at every stage.

Slips and Trips — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Teaching graphic from the linked SHAREhub source section.

Understand the activity and how harm develops

The level entrance is especially important to people who cannot use steps. If ice covers it, directing everyone to a stepped entrance may remove their access rather than control the risk. Weather can change quickly, and meltwater may refreeze after an earlier treatment.

Plan who monitors forecasts, inspects the actual route and arranges treatment before busy periods. Prioritise the entrance, vehicle drop-off and necessary outside journeys. A record that grit was spread is an action record; it does not establish that the surface now provides safe footing or remains usable later in the shift.

Recognise the evidence boundary

QuestionCase evidence
What is observed?Ice covers the level route while the alternative includes difficult steps.
How can harm occur?People may slip or be forced onto an unsuitable route.
What information is needed?Check weather response, treatment effectiveness and residents' access needs.

Protect, manage and verify

PurposePractical application
Immediate protectionProtect the affected approach and provide a genuinely usable alternative while treating it.
Accountable work arrangementDuty manager and premises team, including evening and weekend cover. Ice remains or returns, and the alternative does not meet the person’s access needs.
Release verificationVerify the route is safe to use and continue monitoring changing conditions.

Apply this at work

Make winter plans a cycle of forecast, action, inspection and reassessment, with access needs included at every stage.

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

Control classification: Classify the mechanism separately from its upkeep: physical floor repair, drainage, barriers, protected routes, compartmentation, fire doors and suitable disposal facilities are physical measures where specified. Cleaning schedules, inspections, policies, funding, supervision and verification are administrative arrangements maintaining them. A verbal instruction is not a physical barrier. Read this correction with the source table. Retained overview and stage artwork requires the matching classification update.

Remove or reduce the hazard before relying on procedures or personal protection.

For slips and trips, assess the actual task and first look for a way to remove the hazard. Where that is not possible, consider a safer substitute, engineered separation and then clear work procedures. PPE protects against remaining exposure; it does not make an uncontrolled task safe. HSE hierarchy of controls

The selected measures need a named owner, a usable stop point and a check that they still work when the task or conditions change. In Northern Ireland, verify the separate legal route and site instructions.

For the wet entrance, eliminate recurring water entry at source where practicable. Reduce contamination with suitable matting, drainage and a cleaning method that leaves the route safe; physically prevent access while unsafe and provide an alternative. Repair floor and route defects, then select footwear for residual risk and sustain checks. ERICPD (Eliminate, Reduce, Isolate, Control, PPE, Discipline) is a teaching prompt; Discipline means competent cleaning, supervision and defect closure. HSE slip and trip factors; HSE barriers and cleaning.

How can the ERICPD hierarchy of controls remove slip and trip hazards from workplace routes?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ERICPD control levelTopic-specific exampleSource and full task context
Eliminate

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Reduce

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Isolate

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Control

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Discipline

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ESEAP mapping crosswalk: these are retained ERICPD source rows, mapped to the five ESEAP levels. Read the control-classification correction for mixed physical and administrative measures; six source rows do not mean six ESEAP levels.
Five-level control stage(s)Topic-specific exampleSource and full task context
Elimination

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Administrative controls

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

Applied case

The morning sheet says “gritted”, but the accessible path is visibly icy again after sunset.

Decision and explanation

Protect the route, reassess treatment and provide accessible assistance.

The signature cannot establish present traction or prevent refreezing. An unassessed transfer of people and equipment creates additional risk. Conditions have changed; the earlier record does not override the current surface.

Lesson 11

Garden security, consent and freedom must be assessed together

Every restriction should have a specific purpose, an appropriate lawful basis, proportionate alternatives and a planned review.

Safety professional reviewing guidance and documents in a UK workplace office. Photorealistic illustration.
Photorealistic illustrative UK workplace scene. Review checks: Customers and visitors: Controls slips, access, supervision, emergencies and information. Workers: Manages training, workload, stress, lone work and task risks. Contractors: Checks competence, provides information and monitors work.

Understand the activity and how harm develops

A locked garden gate may reduce one risk while creating distress, preventing a familiar activity or interfering with escape. A diagnosis or age alone does not determine what a person can decide. Establish what the resident wants, the particular risk and which less restrictive support could meet their needs.

In England, care and consent arrangements should follow the applicable person-centred and mental-capacity framework. Where a person lacks capacity for the specific decision, the appropriate lawful process and authorised safeguards are needed. A generic “for safety” notice does not supply that authority, and fire-release arrangements still need to work.

Recognise the evidence boundary

QuestionCase evidence
What is observed?A new locked garden gate prevents a resident using their usual route.
How can harm occur?An unassessed restriction can compromise autonomy, distress the person or obstruct emergency arrangements.
What information is needed?Ask about the person's wishes and the individual and emergency assessments supporting the change.

Protect, manage and verify

PurposePractical application
Immediate protectionReview the restriction through the appropriate person-centred and lawful decision process.
Accountable work arrangementRegistered manager with the person, appropriate representatives and relevant professionals. The restriction has no clear individual assessment, lawful basis or workable emergency arrangement.
Release verificationConfirm agreed access, assistance and compatible emergency arrangements in practice.

Apply this at work

Every restriction should have a specific purpose, an appropriate lawful basis, proportionate alternatives and a planned review.

What does reasonable care look like in practice?

Reasonable care is proportionate, risk-based action that a competent organisation can explain and evidence.

Reasonable care normally starts with a suitable risk assessment, but it does not end there. The control must be implemented, communicated, maintained and checked. The level of care expected increases where the harm is severe, the hazard is well known, the control is straightforward or the people affected are vulnerable.

For example, it is reasonable to expect a shop or leisure centre to inspect public walkways, respond to spillages, provide clear warning, repair defects and record significant issues. It is reasonable to expect an employer to assess DSE and work-related stress, not just physical injury hazards. It is reasonable to expect a contractor to protect others from the hazards created by its work.

Reasonable care examples - Reasonable care examples
Situation Reasonable care includes Weak practice
Slip risk Cleaning regime, inspections, matting, repairs and prompt response. Only putting a sign out after someone falls. Sources: HSE - Managing for health and safety HSG65.
Remote work DSE guidance, communication, workload review and reporting route. Assuming home work is outside employer concern. Sources: HSE - Managing for health and safety HSG65.
Visitor access Clear routes, restricted areas, induction or escort where needed. Visitors wandering through operational areas. Sources: HSE - Managing for health and safety HSG65.
Contractor work Competence check, information exchange, induction and monitoring. Contractors left to self-authorise on unfamiliar site. Sources: HSE - Managing for health and safety HSG65.
Work-related stress Stress risk assessment, workload review, support and manager training. Treating repeated stress reports as personal weakness. Sources: HSE - Managing for health and safety HSG65.

Applied case

A new padlock stops one resident reaching their usual garden seat. Staff say it is now the rule for everybody.

Decision and explanation

Review the individual need, less restrictive options and lawful decision process.

A proportionate supported arrangement needs to address the person and the actual risk. Diagnosis does not establish capacity for this decision or authorise blanket restrictions. Removing a restriction without reviewing the individual and emergency risks is also inadequate.

Lesson 12

Winter evening at the entrance

Defend a practical access plan without unnecessary restriction.

Maintaining temporary roof-edge protection — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Winter evening at the entrance

In this fictional care home, an evening delivery arrives later than planned. A resident wants to visit the garden using their usual mobility aid and support. The level path has refrozen after the morning treatment, a van occupies the suggested diversion and the temporary gate is padlocked without an individual review. The premises team reports that a raised slab was repaired, but the barriers remain and the route has not been checked in current light.

Describe each problem and who it affects. Reversing traffic can strike or trap a person in the delivery envelope. Ice and the repaired step affect footing or the mobility aid's passage. The diversion may be unusable with the support the person needs. The padlock introduces a separate restriction decision. A signed maintenance record, driver's familiarity or earlier treatment sheet cannot settle all these questions.

Coordinate an immediate safe hold of the conflicting vehicle movement through the actual plan. Do not place a worker behind the vehicle to make it stop. Ask the person about the visit and appropriate support, then arrange a genuinely usable alternative where available. Keep the physical repair and temporary access response separate from the lawful person-specific review of the gate restriction. A resident's diagnosis alone does not justify applying a blanket ban.

The premises owner should verify the repaired surface, current ice response, lighting and complete route, including the return journey. A contractor invoice records work but does not establish the outcome under evening conditions. Do not use the resident as a test on an uncertain surface. Appropriate safe checks and competent information should precede reopening. If an alternative route is proposed, confirm the necessary space, surface and assistance rather than judging it only from a plan.

The care lead should use the applicable consent and lawful decision-making arrangements for any restriction, involving the person and relevant others appropriately. This course does not authorise a capacity finding or deprivation of liberty. Record unknown arrangements as questions rather than inventing an approval. Explain interim support respectfully so the person does not experience the unresolved maintenance problem simply as a cancelled choice.

The final handover should state the delivery wait, usable access, support, physical actions, restriction review, responsible roles and evidence needed before release. Check that the next shift understands current conditions and review triggers, including refreezing or another vehicle arrival. Use the fictional risk and audit prompts without submitting a real care record. A practice result demonstrates awareness; it cannot approve a resident's restriction or certify the premises. The case is complete when the arrangement supports the person's intended journey with effective physical and lawful safeguards.

How should the basic risk assessment process work?

The process should identify hazards, decide who may be harmed, evaluate risk, record significant findings and review the controls.

The familiar five-step model is only useful when each step is done honestly. Walking the workplace, checking incident data, speaking to workers, reviewing maintenance, reading safety data sheets and observing non-routine work will usually reveal more than a desk exercise.

The output should be understandable to the people who use it. A supervisor should know what must be in place before work starts. A worker should know the task controls and stop-work triggers. A manager should know what resources and review evidence are required.

StepWhat good looks likeEvidence
Identify hazardsTask observation includes normal, abnormal, maintenance, cleaning and emergency conditions.Walkthrough notes, worker input and hazard register.
Decide who may be harmedEmployees, contractors, visitors, public, vulnerable workers and emergency responders are considered.People-at-risk section and consultation evidence.
Evaluate riskExisting controls are tested, not assumed.Inspection findings, monitoring data, maintenance records and competence checks.
Record findingsSignificant risks, controls, action owners and review triggers are clear.Assessment, action tracker and risk register.
ReviewAssessment changes after incidents, changes, new information or weak control evidence.Review log and closure evidence.

HSENI provides the Northern Ireland five-step route. HSENI five steps to risk assessment.

Applied case

The team proposes keeping the padlock and letting the delivery finish while waiting for daylight.

Decision and explanation

Coordinate immediate vehicle protection, usable individual support, current route verification and lawful restriction review.

Protect the actual journey while resolving the separate physical and person-specific decisions.

Lesson 13

Take a verified action into the workplace

Connect one actual task to an owner, evidence and a clear release or escalation decision.

Maintaining temporary roof-edge protection — ERICPD planning crossmap. ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level
Related SHAREhub topic guide. Apply its prompts to the specific case below.

Turn awareness into a practical question

Care-home safety awareness with a Great Britain workplace baseline. CQC, DHSC and cited residential-care examples apply to England where stated; confirm the relevant national regime. This course does not confer clinical, medicines, lifting, restraint, maintenance or emergency-response competence or authorisation.

Choose one relevant operation from the course. Describe the person or environment at risk, the mechanism of harm and the exact condition that needs controlling. Separate an observation from a conclusion. A display, signature, badge or clean appearance answers only a limited question.

Use the included practice resources to prepare a fictional task brief, risk review or verification question. Decide which competent role owns the decision and which evidence must be available before work restarts or work is released. Keep worker protection, public exclusion, task acceptance and environmental decisions distinct where required.

At work, use your actual approved arrangements. Report uncertainty and preserve the relevant hold, restriction or safe state while it is resolved. Confirm that the action addressed the original harm route and check whether another shift, load, cleaning task or maintenance change could reintroduce it.

Course completion records awareness learning. It does not establish practical competence, certify an organisation or authorise specialist, clinical, maintenance, chemical or emergency work.

How should the basic risk assessment process work?

The process should identify hazards, decide who may be harmed, evaluate risk, record significant findings and review the controls.

The familiar five-step model is only useful when each step is done honestly. Walking the workplace, checking incident data, speaking to workers, reviewing maintenance, reading safety data sheets and observing non-routine work will usually reveal more than a desk exercise.

The output should be understandable to the people who use it. A supervisor should know what must be in place before work starts. A worker should know the task controls and stop-work triggers. A manager should know what resources and review evidence are required.

StepWhat good looks likeEvidence
Identify hazardsTask observation includes normal, abnormal, maintenance, cleaning and emergency conditions.Walkthrough notes, worker input and hazard register.
Decide who may be harmedEmployees, contractors, visitors, public, vulnerable workers and emergency responders are considered.People-at-risk section and consultation evidence.
Evaluate riskExisting controls are tested, not assumed.Inspection findings, monitoring data, maintenance records and competence checks.
Record findingsSignificant risks, controls, action owners and review triggers are clear.Assessment, action tracker and risk register.
ReviewAssessment changes after incidents, changes, new information or weak control evidence.Review log and closure evidence.

HSENI provides the Northern Ireland five-step route. HSENI five steps to risk assessment.

Applied case

The shift action log says “training completed, issue closed”. It records no condition check, work status or task owner.

Decision and explanation

The accountable person verifies the task-specific control and records the justified decision.

Learning supports the decision; evidence that the relevant control works is needed before the responsible person closes the action.