Construction fire safety and hot work · learning reader
Free training · Approx. 1h 50m–2h 40m · estimated self-paced learning, including activities and assessment.
Public teaching is free without an account. A free learner account is required for confirmed LMS assessment, completion and certificate records. See the full course outline and access routes.
Teaching and applied cases for accessible study. The interactive course records assessed completion.
Lesson 1
Map the construction fire scenario
Assess the actual construction stage, temporary escape, fire loading and people exposed.
Read the workface decision
A construction site changes faster than a finished workplace. Missing doors, open shafts, temporary materials and changing access can alter fire growth and escape at the same time. The assessment needs to follow the phase and work sequence. Consider the people already occupying adjacent areas as well as those carrying out the construction work.
Visual practice · Map the construction fire scenario
SHAREhub photographic illustration · Fire extinguisher and clear emergency route in a UK workplace. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
A construction site changes faster than a finished workplace. Missing doors, open shafts, temporary materials and changing access can alter fire growth and escape at the same time. The assessment needs to follow the phase and work sequence. Consider the people already occupying adjacent areas as well as those carrying out the construction work.
Which construction fire examples need close control?
Construction fire risk changes quickly because the building, services, materials and escape routes can change every day. Construction and refurbishment projects deserve their own fire-prevention lens. Temporary electrical systems may be extended, moved or damaged.
See the actual construction-model example
An alarm that is clearly audible in a quiet cabin may not reach someone beside a saw or inside a partly enclosed floor. The scene combines that warning gap with a changed temporary stair route. These are linked weaknesses: earlier detection is of limited value if people cannot receive the warning, and a mapped escape route is of limited value if it has moved or become obstructed. An unfinished building may have open shafts, missing doors and incomplete fire stopping, so the completed building’s protection cannot be assumed to exist during construction.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Which construction fire examples need close control?
Construction fire risk changes quickly because the building, services, materials and escape routes can change every day.
Construction and refurbishment projects deserve their own fire-prevention lens. Temporary electrical systems may be extended, moved or damaged. Hot works may happen near hidden voids. Waste can build up faster than it is removed. Fire stopping may be incomplete during service installation. Risers may be open. Temporary coverings, scaffold sheeting, timber, insulation, adhesives and gas cylinders can change the fire load and spread route.
A good construction fire plan is therefore live. It should be reviewed as the project moves through strip-out, structural works, fit-out, commissioning and occupation. Supervisors should know which temporary conditions are acceptable, which require a permit or compensating control, and which should stop work.
Example
How fire risk increases
Control and evidence
Temporary electrics
Damaged cables, overloaded supplies or poor charger locations can ignite materials.
Temporary electrical inspection, route protection and defect removal.
Hot works
Sparks or heat reach hidden voids, insulation, dust or waste.
Hot work permit, isolation, fire watch and post-work inspection.
Waste build-up
Packaging, offcuts and pallets create fuel and obstruct routes.
Waste schedule, skip separation and daily supervisor checks.
Incomplete fire stopping
Open penetrations allow smoke/fire through compartments.
Fire-stopping permit, photo evidence and competent sign-off.
Open risers or voids
Smoke and flame can spread vertically or unseen.
Temporary covers, barriers, inspection and sequencing control.
Temporary coverings or sheeting
Combustible coverings increase external or scaffold fire spread.
Material standard, separation, ignition control and fire plan review.
See the actual construction-model example
An alarm that is clearly audible in a quiet cabin may not reach someone beside a saw or inside a partly enclosed floor. The scene combines that warning gap with a changed temporary stair route. These are linked weaknesses: earlier detection is of limited value if people cannot receive the warning, and a mapped escape route is of limited value if it has moved or become obstructed. An unfinished building may have open shafts, missing doors and incomplete fire stopping, so the completed building’s protection cannot be assumed to exist during construction.
The fire plan needs to follow the actual phase, occupied areas, combustible storage, simultaneous work and people who may need assistance. Suitable warning can involve more than sound, particularly where hearing protection, noise, language or individual access needs affect understanding. Escape must lead to a place of safety and allow accountability without directing people into delivery traffic. Testing should expose these practical weaknesses before a fire. Workers should raise the alarm and leave safely; any limited firefighting role depends on appropriate equipment, training and a safe escape, and must never delay evacuation or require entry into smoke.
Evidence to establish at the workface
Review the fire-risk assessment and construction phase arrangements when the layout, occupancy, fuel load or temporary stairs change; assign an owner before the affected phase opens.
Apply the learning
A fire plan assumes the building's final stairs and compartment walls exist, although the project is at an open-frame stage.
Decision and explanation
Assess the actual construction stage, temporary escape, fire loading and people exposed.
A construction site changes faster than a finished workplace. Missing doors, open shafts, temporary materials and changing access can alter fire growth and escape at the same time. The assessment needs to follow the phase and work sequence. Consider the people already occupying adjacent areas as well as those carrying out the construction work.
Lesson 2
Fuel, ignition and oxygen
Separate the hazards through a suitable storage and work plan that also protects escape.
Read the workface decision
The fire triangle helps identify different control opportunities, but real fires also depend on material arrangement, ventilation and spread pathways. Oxygen is not fuel, yet enrichment can make burning more severe. Removing waste, controlling ignition and managing gases prevent the combination forming. A no-smoking sign cannot control heaters, electrical faults or hot work.
Visual practice · Fuel, ignition and oxygen
Actual SHAREsimulate model capture · Gas and fuel are proposed outside controlled storage. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Investigate 1: Secured cylinder area
The cylinder storage cage is visible. The unsafe move beside a heater and escape route is a proposal in the written case, not a visible defect in this capture. Challenge that proposal and verify equivalent controls before any move.
Investigate 2: Separate storage structure
A separate store is shown. Verify the actual products, storage arrangements and access controls from the task information; the model’s enclosure cannot establish the contents or compliance.
Investigate 3: Approach around the store
The surrounding approach is visible. Use the proposed heater and escape-route conflict in the case to test the location decision. Do not treat spare floor space as authorisation to relocate fuel or cylinders.
Read the workface decision
The fire triangle helps identify different control opportunities, but real fires also depend on material arrangement, ventilation and spread pathways. Oxygen is not fuel, yet enrichment can make burning more severe. Removing waste, controlling ignition and managing gases prevent the combination forming. A no-smoking sign cannot control heaters, electrical faults or hot work.
What does the fire triangle explain—and what does it miss?
Fuel, oxidiser and ignition energy must coincide for a fire to start; prevent their contact before ignition. The HSE fire-safety introduction explains the three conditions for a fire to start. Once burning, heat feedback can sustain combustion after the original spark has gone; switching off that spark alone will not extinguish an established fire.
See the actual construction-model example
The site’s secured gas cage and flammable store provide an organised storage arrangement; they do not make a proposed move beside a heater acceptable. Gas, petrol and other flammable products can create ignitable mixtures if they leak or evaporate. Oxygen is different: it is not a fuel but can make materials burn more fiercely. Heat and impact can also damage containers or cylinders. Keeping an escape route clear matters because the same release that starts a fire may block the easiest way out or expose people trying to reach the assembly point.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What does the fire triangle explain—and what does it miss?
Fuel, oxidiser and ignition energy must coincide for a fire to start; prevent their contact before ignition.
The HSE fire-safety introduction explains the three conditions for a fire to start. Once burning, heat feedback can sustain combustion after the original spark has gone; switching off that spark alone will not extinguish an established fire. Keep people clear and follow the evacuation plan. In a solvent-transfer room, fuel is vapour, ordinary air supplies oxygen and a non-rated electrical switch may ignite the cloud. At a waste store, cardboard provides fuel and a hot work spark can start a fire. The triangle helps choose a prevention control, but cannot establish whether a confined dust collector will explode. The HSE combustible-dust guide also considers fine dust, dispersion into a cloud and confinement. A competent process-safety assessment is required for a mill, filter or silo; never rely on a generic premises fire assessment alone.
See the actual construction-model example
The site’s secured gas cage and flammable store provide an organised storage arrangement; they do not make a proposed move beside a heater acceptable. Gas, petrol and other flammable products can create ignitable mixtures if they leak or evaporate. Oxygen is different: it is not a fuel but can make materials burn more fiercely. Heat and impact can also damage containers or cylinders. Keeping an escape route clear matters because the same release that starts a fire may block the easiest way out or expose people trying to reach the assembly point.
Read the actual labels and safety information rather than assume that every cylinder has the same contents or storage needs. The assessment should connect the substance, quantity, pressure, release mechanism, ventilation, incompatibilities and ignition sources. Reduce what is kept on site and control transfers as well as storage. A padlock or warning sign is only one part of the arrangement: it cannot compensate for an open container, a nearby heater or a blocked route. If a leak is suspected, keep people away and use the site’s emergency process; only authorised competent people should attempt the relevant isolation or defect work when safe.
Evidence to establish at the workface
Provide compatible, labelled and secure storage with ventilation, segregation and cylinder restraint matched to the substance, assessment and supplier instructions; protect it from vehicles and impact.
Apply the learning
Packaging, a heater and oxygen equipment are moved into the same corner beside an exit.
Decision and explanation
Separate the hazards through a suitable storage and work plan that also protects escape.
The fire triangle helps identify different control opportunities, but real fires also depend on material arrangement, ventilation and spread pathways. Oxygen is not fuel, yet enrichment can make burning more severe. Removing waste, controlling ignition and managing gases prevent the combination forming. A no-smoking sign cannot control heaters, electrical faults or hot work.
Lesson 3
Prevent fire through layout and housekeeping
Remove the fire load through a planned waste and work-area arrangement before the tasks start.
Read the workface decision
Housekeeping is a designed workflow rather than an end-of-day cosmetic task. Storage locations, collection frequency and contractor interfaces affect how quickly combustible material returns. Keep escape routes and firefighting access usable. Check concealed and adjacent spaces, because sparks and heat may reach fuel beyond the operator's immediate view.
Visual practice · Prevent fire through layout and housekeeping
SHAREhub photographic illustration · Fire extinguisher and clear emergency route in a UK workplace. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Housekeeping is a designed workflow rather than an end-of-day cosmetic task. Storage locations, collection frequency and contractor interfaces affect how quickly combustible material returns. Keep escape routes and firefighting access usable. Check concealed and adjacent spaces, because sparks and heat may reach fuel beyond the operator's immediate view.
How should ignition and fuel be controlled?
Fire prevention is strongest when fuel and ignition are controlled together. Removing ignition sources while leaving poor fuel control is weak. Removing waste while allowing uncontrolled hot work is also weak.
Evidence to establish at the workface
Keep ignition and heat sources away from foreseeable releases and maintain usable escape and responder access. Plan transfers and temporary storage so they preserve equivalent controls.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should ignition and fuel be controlled?
Fire prevention is strongest when fuel and ignition are controlled together.
Removing ignition sources while leaving poor fuel control is weak. Removing waste while allowing uncontrolled hot work is also weak. Good fire prevention links housekeeping, storage, maintenance, electrical condition, contractor control, smoking, hot work, chargers, process equipment and supervision.
Ignition control must be specific. A generic 'no naked flames' rule does not manage damaged cables, overloaded sockets, lithium battery charging, static electricity, grinding sparks, hot bearings, friction, portable heaters or hot surfaces near flammable vapour.
Hazard
Typical failure
Stronger control
Combustible waste
Waste builds up near exits or plant rooms.
Daily removal, skip location rules and inspection.
Hot work
Sparks reach hidden void or combustible material.
Permit, fire watch, isolation, gas test and post-work checks.
Electrical equipment
Damaged leads, overloaded sockets or poor chargers.
Inspection, maintenance, RCDs and removal of defects.
Flammable liquids
Open containers, poor cabinets or incompatible storage.
Small quantities, closed containers, DSEAR assessment and segregation.
Battery charging
Chargers on combustible surfaces or damaged batteries.
Charging area, supervision, defect control and emergency plan.
Smoking/vaping
Poorly controlled smoking areas near waste or gas stores.
Designated areas, bins and inspection.
Evidence to establish at the workface
Keep ignition and heat sources away from foreseeable releases and maintain usable escape and responder access. Plan transfers and temporary storage so they preserve equivalent controls.
Apply the learning
Waste accumulates beneath a temporary stair and beside the area where cutting and grinding begin tomorrow.
Decision and explanation
Remove the fire load through a planned waste and work-area arrangement before the tasks start.
Housekeeping is a designed workflow rather than an end-of-day cosmetic task. Storage locations, collection frequency and contractor interfaces affect how quickly combustible material returns. Keep escape routes and firefighting access usable. Check concealed and adjacent spaces, because sparks and heat may reach fuel beyond the operator's immediate view.
Lesson 4
Assess the changing workface
Reassess who may be affected, warning, routes and response for the changed conditions.
Read the workface decision
A useful assessment identifies a credible fire, the people who could be harmed and the controls needed in the present layout. It should lead to practical priorities, owners and checks rather than a score with no follow-through. Changes in occupancy, enclosure, weather protection and temporary power can alter several parts of the fire scenario together.
Visual practice · Assess the changing workface
Actual SHAREsimulate model capture · A phase change reveals an alarm and escape gap. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
A useful assessment identifies a credible fire, the people who could be harmed and the controls needed in the present layout. It should lead to practical priorities, owners and checks rather than a score with no follow-through. Changes in occupancy, enclosure, weather protection and temporary power can alter several parts of the fire scenario together.
Test the assumptions in the phase plan
For the fictional refurbishment, write down where a person starts, how they discover or receive warning of a fire, and the route they can actually use. Now add a contractor working alone after the main team leaves. A plan that depends on nearby workers shouting may no longer provide a reliable warning. Add the occupied rooms beyond the construction boundary and identify who coordinates their protection. This exercise reveals missing interfaces before any numerical fire-risk rating is assigned.
How can managers test whether a fire risk assessment is good enough?
A good assessment should help managers make decisions, not just prove that a document exists. Managers can test quality by asking whether the assessment reflects the real premises, names specific hazards, identifies vulnerable people, explains control assumptions, prioritises actions and says when review is needed. Weak assessments often contain generic wording, missing drawings, copied photos, no action ownership, no evidence that defects closed and no clear link to drills, maintenance or training.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Test the assumptions in the phase plan
For the fictional refurbishment, write down where a person starts, how they discover or receive warning of a fire, and the route they can actually use. Now add a contractor working alone after the main team leaves. A plan that depends on nearby workers shouting may no longer provide a reliable warning. Add the occupied rooms beyond the construction boundary and identify who coordinates their protection. This exercise reveals missing interfaces before any numerical fire-risk rating is assigned.
How can managers test whether a fire risk assessment is good enough?
A good assessment should help managers make decisions, not just prove that a document exists.
Managers can test quality by asking whether the assessment reflects the real premises, names specific hazards, identifies vulnerable people, explains control assumptions, prioritises actions and says when review is needed.
Weak assessments often contain generic wording, missing drawings, copied photos, no action ownership, no evidence that defects closed and no clear link to drills, maintenance or training.
Review the fire-risk assessment and construction phase arrangements when the layout, occupancy, fuel load or temporary stairs change; assign an owner before the affected phase opens.
Apply the learning
The site adds a night shift and temporary enclosure without changing the warning or escape arrangements.
Decision and explanation
Reassess who may be affected, warning, routes and response for the changed conditions.
A useful assessment identifies a credible fire, the people who could be harmed and the controls needed in the present layout. It should lead to practical priorities, owners and checks rather than a score with no follow-through. Changes in occupancy, enclosure, weather protection and temporary power can alter several parts of the fire scenario together.
Lesson 5
Avoid hot work where practicable
Compare methods and avoid on-site hot work where a suitable safer option can achieve the job.
Read the workface decision
The first useful question is whether heat, sparks or flame need to be introduced at this location. Preparation, cold methods or relocation can remove important ignition pathways. Alternatives still need their own assessment, including sharp edges, adhesives or other equipment hazards. A permit is a control for defined work, not evidence that the chosen process is inherently necessary.
Visual practice · Avoid hot work where practicable
SHAREhub photographic illustration · Welding booth with local extraction and protective screening. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
The first useful question is whether heat, sparks or flame need to be introduced at this location. Preparation, cold methods or relocation can remove important ignition pathways. Alternatives still need their own assessment, including sharp edges, adhesives or other equipment hazards. A permit is a control for defined work, not evidence that the chosen process is inherently necessary.
How should hot work be assessed before it starts?
First test whether the job can be done cold or off-site; a permit follows the risk assessment and verified controls, not the other way round. A flange on a solvent line needs repair. Prefer a bolted replacement or cold cutting after engineering review.
See the actual construction-model example
The welding bay illustrates several controls working together: a defined working area, extraction close to the source and screens protecting people nearby. Moving the job beside the packaging and wall void changes the exposure and the fire pathways. Sparks can enter gaps and ignite concealed combustible material; the operator may finish before smoke becomes visible. Meanwhile the extraction hood remains in the old position, so a running fan provides no reliable protection at the new workface. The person welding, nearby trades and someone on the other side of the wall can all be affected.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should hot work be assessed before it starts?
First test whether the job can be done cold or off-site; a permit follows the risk assessment and verified controls, not the other way round.
A flange on a solvent line needs repair. Prefer a bolted replacement or cold cutting after engineering review. If welding remains, isolate and drain the line, clean residue, test for flammable atmosphere, remove nearby combustibles, control sparks through openings and arrange fire watch and emergency response. The HSE DSEAR guidance explicitly includes hot work on containers that held flammables; HSG250 sets out the permit interface. Stop if gas readings, isolation, boundary or fire-watch cover changes; a new competent check is needed before restart.
See the actual construction-model example
The welding bay illustrates several controls working together: a defined working area, extraction close to the source and screens protecting people nearby. Moving the job beside the packaging and wall void changes the exposure and the fire pathways. Sparks can enter gaps and ignite concealed combustible material; the operator may finish before smoke becomes visible. Meanwhile the extraction hood remains in the old position, so a running fan provides no reliable protection at the new workface. The person welding, nearby trades and someone on the other side of the wall can all be affected.
Start by asking whether the connection can be made using an appropriate cold method or fabricated in a controlled workshop. If hot work remains necessary, assess the actual material, coating, location, adjacent work and hidden spaces. A permit coordinates a particular job and its conditions; the signature does not remove fuel, isolate services or capture fume. Welding fume needs effective source control and suitable respiratory protection where the assessment requires it, while optical screens and appropriate eye and skin protection address the arc. Fire precautions and exposure controls must both survive the change of location.
Evidence to establish at the workface
For the selected location, remove or protect combustibles, investigate both sides and concealed spread paths, and establish required isolation, exclusion and fire precautions before authorisation.
Apply the learning
A bracket could be prepared off site or welded beside combustible wall insulation.
Decision and explanation
Compare methods and avoid on-site hot work where a suitable safer option can achieve the job.
The first useful question is whether heat, sparks or flame need to be introduced at this location. Preparation, cold methods or relocation can remove important ignition pathways. Alternatives still need their own assessment, including sharp edges, adhesives or other equipment hazards. A permit is a control for defined work, not evidence that the chosen process is inherently necessary.
Lesson 6
A permit must match the real job
Stop the changed job and reassess the location, exposures and permit conditions before further work.
Read the workface decision
A permit coordinates a specific scope, place, time and set of precautions. Its value depends on workface verification and the ability to stop when conditions differ. Identify the issuer, receiver, area responsibility and close-out arrangement. Moving a task can change hidden combustibles, other trades, ventilation, access and the reliability of an existing fire watch.
Visual practice · A permit must match the real job
Actual SHAREsimulate model capture · Hot work is proposed outside the controlled bay. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
A permit coordinates a specific scope, place, time and set of precautions. Its value depends on workface verification and the ability to stop when conditions differ. Identify the issuer, receiver, area responsibility and close-out arrangement. Moving a task can change hidden combustibles, other trades, ventilation, access and the reliability of an existing fire watch.
How should a hot-work permit control the job?
A hot-work permit should define the exact scope, place, time, hazards, precautions, authorisations, monitoring and close-out requirements. The permit is not permission to improvise. It authorises a defined job under defined conditions.
Evidence to establish at the workface
At the new workface, compare the permit boundaries with where the welder and sparks can actually reach; challenge any uninspected opening or combustible material behind the work. Observe representative capture from a safe position and check maintenance and performance evidence. A motor noise, test sticker or roof exhaust alone does not prove effective fume capture.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should a hot-work permit control the job?
A hot-work permit should define the exact scope, place, time, hazards, precautions, authorisations, monitoring and close-out requirements.
The permit is not permission to improvise. It authorises a defined job under defined conditions. If the work changes, the location changes, the team changes, weather changes, ventilation fails, gas readings change or another job creates a new risk, the permit should be stopped and reassessed.
A strong permit system includes the permit issuer, permit receiver, area authority, contractor supervisor where relevant, fire watch and operations handover. It should require field verification, not just desk review.
Hot-work permit elements
Permit element
What it should confirm
Common failure
Scope
Exact work, tools, location and boundaries.
Work expands informally.
Fuel removal
Combustibles, vapours, dusts and residues removed or controlled.
Hidden fuel remains.
Isolation
Hazardous energy and substances are isolated and verified.
Valve isolation assumed.
Gas testing
Atmosphere is tested at the right points and time.
Test not representative.
Fire watch
Competent watch provided during and after work.
Watch ends too early.
Close-out
Area and adjacent spaces checked before handback.
Delayed ignition missed.
Evidence to establish at the workface
At the new workface, compare the permit boundaries with where the welder and sparks can actually reach; challenge any uninspected opening or combustible material behind the work. Observe representative capture from a safe position and check maintenance and performance evidence. A motor noise, test sticker or roof exhaust alone does not prove effective fume capture.
Apply the learning
A permit names a workshop bay, but the welder moves beside a wall void to avoid blocking deliveries.
Decision and explanation
Stop the changed job and reassess the location, exposures and permit conditions before further work.
A permit coordinates a specific scope, place, time and set of precautions. Its value depends on workface verification and the ability to stop when conditions differ. Identify the issuer, receiver, area responsibility and close-out arrangement. Moving a task can change hidden combustibles, other trades, ventilation, access and the reliability of an existing fire watch.
Lesson 7
Control heat and concealed spread
Keep hot work on hold until the spread pathway and affected spaces are controlled under the task-specific plan.
Read the workface decision
Heat may travel through metal or ignite material beyond a partition, while embers can produce delayed fire. Planning must cover the other side, lower levels, voids and nearby occupants where relevant. Fire-watch arrangements, including post-work checks, need to follow the assessed job and site requirements. Do not invent one universal watch duration for every construction task.
Visual practice · Control heat and concealed spread
SHAREhub photographic illustration · Welding booth with local extraction and protective screening. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Heat may travel through metal or ignite material beyond a partition, while embers can produce delayed fire. Planning must cover the other side, lower levels, voids and nearby occupants where relevant. Fire-watch arrangements, including post-work checks, need to follow the assessed job and site requirements. Do not invent one universal watch duration for every construction task.
What should fire watch and post-work monitoring include?
Fire watch should monitor for ignition during and after hot work, including hidden spaces where sparks or heat may have travelled. Many fires start after the hot-work team leaves. Sparks can lodge in gaps, insulation, dust, cable trays, roof voids or lower levels.
Evidence to establish at the workface
Eliminate the hot stage where a technically suitable cold connection or off-site fabrication can achieve the job; check that the alternative does not introduce another uncontrolled hazard.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What should fire watch and post-work monitoring include?
Fire watch should monitor for ignition during and after hot work, including hidden spaces where sparks or heat may have travelled.
Many fires start after the hot-work team leaves. Sparks can lodge in gaps, insulation, dust, cable trays, roof voids or lower levels. Heat can transfer through metal to the other side of a wall, tank or deck. A fire watch should therefore understand the work, the fuel, the building, the escape route, alarm method and escalation route.
Set fire watch and post-work checks from the task risk and applicable industry guidance, including any specified minimum watch and later inspection. Hidden voids, combustible construction, tanks, ducts and process plant can require longer or repeated checks; a brief routine look is not a substitute for the agreed watch.
Fire watch and post-work controls
Control
What to check
Evidence
During work watch
Sparks, slag, smoke, heat transfer and exposed combustibles.
Fire watch name and time.
Adjacent area check
Other side of walls, lower floors, roof spaces and voids.
Permit checklist and photographs where useful.
Firefighting readiness
Suitable extinguishers, hose, alarm and escape route.
Pre-work check.
Post-work inspection
Smouldering, odour, heat and hidden ignition.
Post-work sign-off times.
Handover
Shift or contractor handover covers hot-work status.
Handover log.
Escalation
Fire watch knows when to raise alarm and stop work.
Briefing and competence record.
HSE welding fire-watch guidance calls for a watch during and after work where a safe area or removal of combustibles is not achievable, with at least 30 minutes after completion and possible extension to 60 where ignition is hard to detect or slow. Construction guidance HSG168 third edition 2022, paragraphs 122–125 normally specifies continuous watch for at least an hour afterwards and a further check two hours after completion, including hidden and adjacent areas; a different procedure needs a suitable assessment demonstrating minimal fire risk. These are guidance for different settings, not interchangeable universal durations. Agree the applicable plan, named watcher, breaks/handover, alarms and final checks before work.
Evidence to establish at the workface
Eliminate the hot stage where a technically suitable cold connection or off-site fabrication can achieve the job; check that the alternative does not introduce another uncontrolled hazard.
Apply the learning
Sparks can pass through a floor gap into a storage space below the welding bay.
Decision and explanation
Keep hot work on hold until the spread pathway and affected spaces are controlled under the task-specific plan.
Heat may travel through metal or ignite material beyond a partition, while embers can produce delayed fire. Planning must cover the other side, lower levels, voids and nearby occupants where relevant. Fire-watch arrangements, including post-work checks, need to follow the assessed job and site requirements. Do not invent one universal watch duration for every construction task.
Lesson 8
Treat fume and optical radiation as separate hazards
Stop and establish suitable fume capture, protection of nearby people and the other task controls.
Read the workface decision
A fire-safe location does not automatically make welding exposure safe. Fume capture must work at the source and follow the actual task, while screens and suitable protection address optical radiation and other hazards. Nearby trades may be affected without doing the welding. Keep fire, respiratory, electrical and equipment controls connected in the method rather than using one permit to stand in for all of them.
Locate the lungs, branching airways and diaphragm below them. The cutaway reveals structures normally hidden by the chest wall.
Trace the source-to-breathing-zone route in this lesson. Which change would prevent the contaminant reaching the person?
educational illustration · healthy anatomy; enlarged details and teaching colours.View full detail ↗The eye: surface and cutaway
Compare the visible eye with its enlarged side cutaway. Locate the clear front, lens and inner rear lining before following light and visual signals.
Distinguish the protective eye surface from the internal visual pathway. What task-specific protection or workstation change does this lesson require?
educational illustration · healthy anatomy; enlarged details and teaching colours.
Visual practice · Treat fume and optical radiation as separate hazards
Actual SHAREsimulate model capture · Hot work is proposed outside the controlled bay. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
A fire-safe location does not automatically make welding exposure safe. Fume capture must work at the source and follow the actual task, while screens and suitable protection address optical radiation and other hazards. Nearby trades may be affected without doing the welding. Keep fire, respiratory, electrical and equipment controls connected in the method rather than using one permit to stand in for all of them.
Read the hood position as a control question
The actual model shows a controlled bay, while the proposed move is a fictional change to that arrangement. A hood visible in the original position does not prove effective capture at the new weld. Ask what equipment, positioning, work method and performance evidence the competent arrangement requires. Screens must protect others without creating a ventilation or access problem. When the work changes, the team needs a usable stop trigger and a named route to resolve uncertainty rather than a rule that a fan must simply be switched on.
How should contractors be controlled during hot work?
Contractors should be controlled through pre-qualification, induction, permit receiver competence, supervision and workface assurance. Contractors often bring specialist hot-work skills but may not know the host site's hidden hazards, flammable storage, roof construction, pipe contents, drains, voids, emergency actions or DSEAR zones. The host must provide this information and verify that the contractor's method fits the site.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Read the hood position as a control question
The actual model shows a controlled bay, while the proposed move is a fictional change to that arrangement. A hood visible in the original position does not prove effective capture at the new weld. Ask what equipment, positioning, work method and performance evidence the competent arrangement requires. Screens must protect others without creating a ventilation or access problem. When the work changes, the team needs a usable stop trigger and a named route to resolve uncertainty rather than a rule that a fan must simply be switched on.
How should contractors be controlled during hot work?
Contractors should be controlled through pre-qualification, induction, permit receiver competence, supervision and workface assurance.
Contractors often bring specialist hot-work skills but may not know the host site's hidden hazards, flammable storage, roof construction, pipe contents, drains, voids, emergency actions or DSEAR zones. The host must provide this information and verify that the contractor's method fits the site.
A contractor should not self-authorise hot work in a high-risk environment. The permit issuer, area authority and contractor supervisor should agree the task, controls and stop-work triggers. If subcontractors are used, the same standard must flow down.
Contractor hot-work controls
Control
What good looks like
Evidence
Pre-qualification
Contractor approved for hot work and hazardous-site work.
Approved contractor scope.
Induction
Contractor understands alarms, permits, DSEAR zones and emergency actions.
Induction and briefing record.
Permit receiver competence
Person receiving permit understands controls and limits.
Authorisation record.
Supervision
Supervisor checks workface conditions and stops drift.
Workface check record.
Tools and equipment
Equipment is suitable, inspected and controlled.
Inspection and test evidence.
Close-out
Contractor remains for fire watch and handback.
Permit close-out and post-work log.
Evidence to establish at the workface
For the selected location, remove or protect combustibles, investigate both sides and concealed spread paths, and establish required isolation, exclusion and fire precautions before authorisation.
Apply the learning
The fire precautions are satisfactory, but the extraction hood remains in the old bay after welding moves.
Decision and explanation
Stop and establish suitable fume capture, protection of nearby people and the other task controls.
A fire-safe location does not automatically make welding exposure safe. Fume capture must work at the source and follow the actual task, while screens and suitable protection address optical radiation and other hazards. Nearby trades may be affected without doing the welding. Keep fire, respiratory, electrical and equipment controls connected in the method rather than using one permit to stand in for all of them.
Lesson 9
Store cylinders and flammable materials safely
Stop the move and establish suitable segregation, security, handling and protected escape.
Read the workface decision
Storage needs to reflect the materials, cylinder types, compatibility, ventilation, heat, impact and emergency access. A cage controls some access and impact issues but cannot neutralise every release or ignition source. Keep the inventory and responsible people clear. Changes in delivery quantities and temporary accommodation can turn a previously suitable storage point into a poor arrangement.
Visual practice · Store cylinders and flammable materials safely
SHAREhub photographic illustration · Closed flammable-liquid cabinet and controlled process area. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Storage needs to reflect the materials, cylinder types, compatibility, ventilation, heat, impact and emergency access. A cage controls some access and impact issues but cannot neutralise every release or ignition source. Keep the inventory and responsible people clear. Changes in delivery quantities and temporary accommodation can turn a previously suitable storage point into a poor arrangement.
What does good storage and housekeeping look like?
Good storage keeps fire load controlled, escape routes clear, flammable materials secure and combustible waste away from buildings and ignition sources. Housekeeping is not cosmetic. It is a fire-control barrier.
Evidence to establish at the workface
Walk the complete store and workface arrangement: examine contents labels, closures, restraint, ventilation and signs of damage without manipulating suspect equipment. Compare the proposed heater, charging station and vehicle movements with the dangerous-substance assessment, and verify that evacuation routes remain usable in the credible release scenario.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What does good storage and housekeeping look like?
Good storage keeps fire load controlled, escape routes clear, flammable materials secure and combustible waste away from buildings and ignition sources.
Housekeeping is not cosmetic. It is a fire-control barrier. Packaging, cardboard, pallets, textiles, foam, waste, stock and displays can all increase fire load. Poor storage can block sprinklers, stop smoke control working as assumed, hide ignition sources, obstruct extinguishers, wedge fire doors and compromise escape routes.
Flammable liquids and gases need more discipline than general storage. They should be identified, labelled, kept closed, stored in suitable containers or cabinets, separated from ignition sources and incompatible materials, ventilated where required and kept to the minimum quantity needed. Damaged containers, decanting, unlabelled bottles and flammable waste should be treated as control failures.
Storage and housekeeping controls
Area
What good looks like
Common failure
Inspection question
External bins and skips
Stored securely away from walls, doors, windows, canopies and escape routes.
Bins left against buildings overnight or moved by members of the public.
Could a bin fire spread into the premises or affect escape?
Combustible storage
Limited quantities, tidy layout, dedicated storage areas and no storage in escape routes.
Stock, decorations or furniture stored in corridors, stairs or plant rooms.
Would this material accelerate fire or block evacuation?
Flammable liquid containers
Closed, labelled, compatible, secure and stored in suitable cabinets or stores.
Open tins, unlabelled bottles, excessive stock or poor spill control.
Is the quantity justified and are containers suitable?
LPG and gas cylinders
Secured upright, protected from heat, segregated and kept to minimum required stock.
Spare cylinders indoors, damaged hoses or cylinders near exits.
Could cylinders become involved in fire or block emergency access?
Waste and contaminated rags
Removed frequently and kept in suitable closed containers.
Oily rags, wipes or cardboard left at end of shift.
Is there a close-down check and safe disposal route?
Charging areas
Designated, ventilated where needed, away from combustibles and supervised according to risk.
Ad hoc charging on desks, in stores, corridors or near packaging.
Could a battery or charger fire spread before detection?
Walk the complete store and workface arrangement: examine contents labels, closures, restraint, ventilation and signs of damage without manipulating suspect equipment. Compare the proposed heater, charging station and vehicle movements with the dangerous-substance assessment, and verify that evacuation routes remain usable in the credible release scenario.
Apply the learning
The secured gas cage is moved beside a heater and its door opens into an escape route.
Decision and explanation
Stop the move and establish suitable segregation, security, handling and protected escape.
Storage needs to reflect the materials, cylinder types, compatibility, ventilation, heat, impact and emergency access. A cage controls some access and impact issues but cannot neutralise every release or ignition source. Keep the inventory and responsible people clear. Changes in delivery quantities and temporary accommodation can turn a previously suitable storage point into a poor arrangement.
Lesson 10
Respond to a suspected gas leak
Keep people away, raise the alarm and follow trained safe isolation and emergency arrangements without introducing ignition.
Read the workface decision
A suspected release creates uncertainty about the atmosphere and potential ignition. Prevent people entering to investigate without the right competence, information and controls. Site emergency arrangements should identify the materials, contact route and safe actions. Do not operate equipment or improvise a leak test in a way that could ignite a flammable mixture.
Visual practice · Respond to a suspected gas leak
Actual SHAREsimulate model capture · Gas and fuel are proposed outside controlled storage. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
A suspected release creates uncertainty about the atmosphere and potential ignition. Prevent people entering to investigate without the right competence, information and controls. Site emergency arrangements should identify the materials, contact route and safe actions. Do not operate equipment or improvise a leak test in a way that could ignite a flammable mixture.
How should isolation and gas testing support hot work?
Isolation and gas testing should prove that hazardous substances and flammable atmospheres are controlled before heat is introduced. Isolation should be designed around the hazard. For flammable liquids, gases, vapours or residues, simply closing a valve may not be enough.
Evidence to establish at the workface
Review the substances required and minimise inventory, choosing a suitable less hazardous product or method where practicable; keep only controlled working quantities at the point of use.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should isolation and gas testing support hot work?
Isolation and gas testing should prove that hazardous substances and flammable atmospheres are controlled before heat is introduced.
Isolation should be designed around the hazard. For flammable liquids, gases, vapours or residues, simply closing a valve may not be enough. Draining, venting, flushing, purging, blinding, disconnection, lock-off and verification may be required. HSE HSG253 is relevant because poor isolation can expose workers to unexpected release during maintenance and hot work.
Gas testing is valuable but limited. It tests the atmosphere at a location and time; it may not detect residues in seams, sludge, dead legs, porous materials or hidden spaces. Where conditions can change, continuous monitoring or repeat testing may be required.
Physical isolation suitable for the substance and energy.
Unexpected release into hot-work area.
Cleaning and gas-freeing
Residues are removed, not merely assumed absent.
Heating creates vapour from remaining residues.
Representative gas test
Tests likely accumulation points, not only open air.
Flammable pockets missed.
Continuous monitoring
Used where atmosphere may change.
Release occurs after initial test.
Competent tester
Tester understands instrument limits and calibration.
False confidence from poor testing.
Recorded results
Readings, time, location and tester are recorded.
No evidence for permit decision.
Evidence to establish at the workface
Review the substances required and minimise inventory, choosing a suitable less hazardous product or method where practicable; keep only controlled working quantities at the point of use.
Apply the learning
Workers report a gas smell beside stored cylinders and propose finding the leak with a flame.
Decision and explanation
Keep people away, raise the alarm and follow trained safe isolation and emergency arrangements without introducing ignition.
A suspected release creates uncertainty about the atmosphere and potential ignition. Prevent people entering to investigate without the right competence, information and controls. Site emergency arrangements should identify the materials, contact route and safe actions. Do not operate equipment or improvise a leak test in a way that could ignite a flammable mixture.
Lesson 11
Battery charging and damaged packs
Keep people safe, stop use through the trained defect process and manage the battery under manufacturer and site emergency arrangements.
Read the workface decision
Lithium-ion failure can escalate rapidly and release hazardous smoke. A normal charging location needs suitable equipment compatibility, inspection and clear routes; a damaged pack requires a defect response beyond routine charging. Do not puncture, dismantle or attempt an untrained repair. An awareness learner should recognise the condition and activate the planned response rather than handle a deteriorating battery experimentally.
Visual practice · Battery charging and damaged packs
SHAREhub photographic illustration · Guarded bench grinder and powered tools in a UK workshop. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Lithium-ion failure can escalate rapidly and release hazardous smoke. A normal charging location needs suitable equipment compatibility, inspection and clear routes; a damaged pack requires a defect response beyond routine charging. Do not puncture, dismantle or attempt an untrained repair. An awareness learner should recognise the condition and activate the planned response rather than handle a deteriorating battery experimentally.
How should batteries and chargers be controlled?
Battery-powered equipment can reduce cable and shock risks, but damaged chargers, lithium batteries and poor charging arrangements can create fire, burn and electrical risks. Moving to cordless tools does not remove the need for electrical control. Chargers, batteries, extension leads, storage bags and charging locations become part of the risk assessment.
See the actual construction-model example
The charging point supports routine inspection and controlled charging, but a swollen or damaged battery is outside normal service conditions. Continuing to charge it using an unverified replacement lead introduces both a battery defect and an equipment-compatibility question. Lithium-ion failure can escalate rapidly and release toxic smoke. Nearby packaging provides additional fuel, while a charging position on an exit route can compromise escape before anyone has time to organise a response. The reported swelling triggers the defect procedure; neither the model nor external appearance establishes the battery’s internal condition.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
How should batteries and chargers be controlled?
Battery-powered equipment can reduce cable and shock risks, but damaged chargers, lithium batteries and poor charging arrangements can create fire, burn and electrical risks.
Moving to cordless tools does not remove the need for electrical control. Chargers, batteries, extension leads, storage bags and charging locations become part of the risk assessment. Lithium batteries in particular should be protected from impact, heat, water, incompatible chargers and charging in escape routes or combustible storage areas.
HSE construction fire guidance identifies short circuits, damage, extreme temperature and over-charging of batteries in plant and tools as ignition risks. Apply the actual battery and charger instructions, and assess other workplaces for their own charging and fire conditions. See HSE HSG168 fire safety in construction.
A practical system sets rules for approved chargers, damaged battery quarantine, charging locations, overnight charging, fire detection or supervision where needed, separation from combustibles, and emergency action if a battery becomes hot, swollen, leaking, smoking or physically damaged.
Issue
What can go wrong
Control standard
Incompatible charger
Wrong charger can overheat or damage battery.
Use manufacturer-approved chargers and procurement control.
Damaged battery
Dropped, crushed, swollen or leaking batteries can fail or ignite.
Quarantine and dispose through competent route; do not recharge.
Poor charging location
Fire can spread to combustibles or block escape routes.
Designated charging area away from exits, waste and flammable storage.
Overnight/unattended charging
Failure may go unnoticed.
Risk-assess need, supervision, detection, isolation and manufacturer instructions.
Wet or dusty charging
Electrical and fire risk increases.
Keep chargers dry, ventilated and protected.
Mixed ownership
Personal or contractor chargers introduced uncontrolled.
Approved equipment rules and site-entry checks.
Emergency response
Workers may handle a failing battery incorrectly.
Brief stop-use, isolation, evacuation and fire-response arrangements.
A cool damaged battery awaiting a planned safe disposal route differs from a hot, smoking or failing battery. For the latter, use the site’s emergency/evacuation response and keep people away; an ordinary user should not carry it to a quarantine box.
See the actual construction-model example
The charging point supports routine inspection and controlled charging, but a swollen or damaged battery is outside normal service conditions. Continuing to charge it using an unverified replacement lead introduces both a battery defect and an equipment-compatibility question. Lithium-ion failure can escalate rapidly and release toxic smoke. Nearby packaging provides additional fuel, while a charging position on an exit route can compromise escape before anyone has time to organise a response. The reported swelling triggers the defect procedure; neither the model nor external appearance establishes the battery’s internal condition.
The immediate decision is to prevent charging and use the site’s defect procedure. Distinguish a suspect item that can be dealt with through a competent planned arrangement from one that is already hot, smoking or failing: that is an emergency and should not be carried through occupied cabins. The manufacturer’s instructions, condition checks, compatible charging equipment and a suitable location form the prevention system. The wider fire assessment must cover warning, occupancy, nearby combustibles, response and disposal. This learning scene does not specify a homemade battery container or a universal firefighting method; those decisions require appropriate competent and emergency-service advice.
Evidence to establish at the workface
Check the battery identification, condition and charger compatibility against the actual manufacturer information; a connector fitting the socket is not evidence of compatibility. Inspect the charging location when it is in use: packaging has not accumulated, exits are available and the agreed monitoring or detection arrangement is effective.
Apply the learning
A swollen battery is still charging beside packaging on the only exit route.
Decision and explanation
Keep people safe, stop use through the trained defect process and manage the battery under manufacturer and site emergency arrangements.
Lithium-ion failure can escalate rapidly and release hazardous smoke. A normal charging location needs suitable equipment compatibility, inspection and clear routes; a damaged pack requires a defect response beyond routine charging. Do not puncture, dismantle or attempt an untrained repair. An awareness learner should recognise the condition and activate the planned response rather than handle a deteriorating battery experimentally.
Lesson 12
Preserve compartmentation during work
Restore the planned protection or establish authorised temporary measures that maintain safe occupation and escape.
Read the workface decision
Construction and refurbishment can remove the very barriers people rely on to escape. Openings, doors and temporary enclosures need coordination with those responsible for the building and site fire arrangements. The finished design is not evidence that protection exists today. Record impairments, control the affected work and verify reinstatement rather than allowing hidden defects to disappear behind finishes.
Visual practice · Preserve compartmentation during work
Actual SHAREsimulate model capture · A phase change reveals an alarm and escape gap. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Construction and refurbishment can remove the very barriers people rely on to escape. Openings, doors and temporary enclosures need coordination with those responsible for the building and site fire arrangements. The finished design is not evidence that protection exists today. Record impairments, control the affected work and verify reinstatement rather than allowing hidden defects to disappear behind finishes.
Keep impairment visible until restored
Imagine that fire-stopping work is assigned to a contractor who cannot attend for several days. The temporary state needs its own decision: which people or work are affected, what restrictions or compensating measures are appropriate, who owns them and when they will be checked. A future work order is not evidence that the barrier is present. At reinstatement, the receiving responsible person needs evidence suitable for the particular construction and location; concealed work should not become impossible to verify after it is covered.
How does fire and smoke spread through workplaces?
Fire and smoke spread through open doors, voids, penetrations, ducts, combustible linings, external routes and poor storage. Fire spread is not only a flame front moving across a room. Smoke can move through ceiling voids, service risers, poorly sealed penetrations, ductwork and open doors long before people see flames.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Keep impairment visible until restored
Imagine that fire-stopping work is assigned to a contractor who cannot attend for several days. The temporary state needs its own decision: which people or work are affected, what restrictions or compensating measures are appropriate, who owns them and when they will be checked. A future work order is not evidence that the barrier is present. At reinstatement, the receiving responsible person needs evidence suitable for the particular construction and location; concealed work should not become impossible to verify after it is covered.
How does fire and smoke spread through workplaces?
Fire and smoke spread through open doors, voids, penetrations, ducts, combustible linings, external routes and poor storage.
Fire spread is not only a flame front moving across a room. Smoke can move through ceiling voids, service risers, poorly sealed penetrations, ductwork and open doors long before people see flames. Heat can attack adjacent compartments, external cladding, stored materials, plant, cylinders or process equipment. That is why everyday actions such as wedging a fire door, drilling unsealed cable holes or storing pallets against an external wall can weaken the fire strategy.
The practical test is simple: if a fire starts here, what stops smoke, heat and flame moving to people, escape routes, neighbours, critical equipment or higher-hazard areas?
Pathway
What can go wrong
Evidence/control
Open or damaged fire door
Smoke and heat pass into escape route.
Fire door inspection and repair log.
Unsealed service penetration
Fire moves through wall, floor or riser.
Fire-stopping register and contractor control.
Ceiling or roof void
Hidden spread beyond the room of origin.
Compartmentation survey and inspection.
Duct or extraction route
Smoke/flame moves through ventilation or grease deposits.
Cleaning, dampers and maintenance records.
External storage
Fire spreads to building facade or openings.
Storage separation and waste controls.
Process escalation
Fire impinges on vessel, pipework or cylinders.
Separation, cooling, isolation and emergency response.
Evidence to establish at the workface
Maintain suitable escape, lighting, signs and phased fire protection appropriate to the actual risk. Keep assembly and responder access separate from uncontrolled vehicle movements.
Apply the learning
New service holes pass through a separating wall and temporary storage props open a fire door.
Decision and explanation
Restore the planned protection or establish authorised temporary measures that maintain safe occupation and escape.
Construction and refurbishment can remove the very barriers people rely on to escape. Openings, doors and temporary enclosures need coordination with those responsible for the building and site fire arrangements. The finished design is not evidence that protection exists today. Record impairments, control the affected work and verify reinstatement rather than allowing hidden defects to disappear behind finishes.
Lesson 13
Make warnings effective for everyone
Verify effective warning and response for all affected people and work conditions before the area is occupied.
Read the workface decision
A warning system is a chain: detection or discovery, raising the alarm, receiving the message, understanding it and acting in time. Noise, hearing protection, language and individual support needs can interrupt that chain. Test representative conditions and provide an appropriate solution. A device's presence or a test in a quiet office cannot prove the construction workface receives a usable warning.
Visual practice · Make warnings effective for everyone
SHAREhub photographic illustration · Fire-safety engineer inspecting a workplace fire alarm control panel. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
A warning system is a chain: detection or discovery, raising the alarm, receiving the message, understanding it and acting in time. Noise, hearing protection, language and individual support needs can interrupt that chain. Test representative conditions and provide an appropriate solution. A device's presence or a test in a quiet office cannot prove the construction workface receives a usable warning.
Who may need different emergency communication?
Warning arrangements must work for all relevant persons, not only regular staff. The fire risk assessment should consider disabled people, visitors, contractors, lone workers, night workers, people in noisy areas, people wearing hearing protection, people in plant rooms, people who do not speak English confidently and members of the public. Communication arrangements may include visual alarms, vibrating devices, buddy systems, PEEPs, refuge communication, public-address messages, radios, marshals or pre-briefed contractor arrangements.
Evidence to establish at the workface
Review the fire-risk assessment and construction phase arrangements when the layout, occupancy, fuel load or temporary stairs change; assign an owner before the affected phase opens.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Who may need different emergency communication?
Warning arrangements must work for all relevant persons, not only regular staff.
The fire risk assessment should consider disabled people, visitors, contractors, lone workers, night workers, people in noisy areas, people wearing hearing protection, people in plant rooms, people who do not speak English confidently and members of the public.
Communication arrangements may include visual alarms, vibrating devices, buddy systems, PEEPs, refuge communication, public-address messages, radios, marshals or pre-briefed contractor arrangements.
Review the fire-risk assessment and construction phase arrangements when the layout, occupancy, fuel load or temporary stairs change; assign an owner before the affected phase opens.
Apply the learning
The alarm is audible in the cabin but cannot be heard beside noisy cutting and inside an enclosure.
Decision and explanation
Verify effective warning and response for all affected people and work conditions before the area is occupied.
A warning system is a chain: detection or discovery, raising the alarm, receiving the message, understanding it and acting in time. Noise, hearing protection, language and individual support needs can interrupt that chain. Test representative conditions and provide an appropriate solution. A device's presence or a test in a quiet office cannot prove the construction workface receives a usable warning.
Lesson 14
Keep escape routes usable as the site changes
Hold occupation or work as necessary until the real route, signs, access and briefing are reconciled.
Read the workface decision
Escape depends on a continuous usable path from where people work to a place of safety. Changes in stairs, hoarding, storage and security can break that path without changing the fire itself. Include visitors, isolated workers and people needing assistance. Route checks and drills should reflect the actual construction phase and result in correction when an assumption fails.
Visual practice · Keep escape routes usable as the site changes
Actual SHAREsimulate model capture · A phase change reveals an alarm and escape gap. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Escape depends on a continuous usable path from where people work to a place of safety. Changes in stairs, hoarding, storage and security can break that path without changing the fire itself. Include visitors, isolated workers and people needing assistance. Route checks and drills should reflect the actual construction phase and result in correction when an assumption fails.
What does a complete fire evacuation pathway look like?
A complete pathway follows the event from alarm activation through recognition, movement, assistance, accountability, fire service information and re-entry control. Evacuation should be tested as a sequence rather than a single drill time. A fast drill is not enough if some people did not hear the alarm, visitors were not directed, a refuge call was unanswered, the assembly point was unsafe or nobody controlled re-entry.
Evidence to establish at the workface
Test the warning under representative operating conditions and ask people at the least favourable positions what they heard, saw and understood; resolve failed coverage before relying on it. Walk each affected route from workface to safety after the phase change. Check it exists, is usable, has appropriate illumination and does not terminate behind a locked gate.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What does a complete fire evacuation pathway look like?
A complete pathway follows the event from alarm activation through recognition, movement, assistance, accountability, fire service information and re-entry control.
Evacuation should be tested as a sequence rather than a single drill time. A fast drill is not enough if some people did not hear the alarm, visitors were not directed, a refuge call was unanswered, the assembly point was unsafe or nobody controlled re-entry.
The pathway should be realistic for the building as used: public visitors, contractors, lone workers, night staff, disabled people, security-controlled doors, bad weather, shift handover and blocked routes should all be considered where relevant.
Fire evacuation pathway
Pathway step
What must happen
Evidence or quality test
Pathway stepAlarm
What must happenFire is detected or reported and the alarm is raised without delay.
Evidence or quality testAlarm test, call point availability and detection maintenance.
Pathway stepRecognition
What must happenPeople understand that they must act now.
Evidence or quality testClear sounders, visual alarms, voice messages or staff instruction.
Pathway stepMovement
What must happenPeople move by safe, direct and available routes.
Evidence or quality testRoute inspections, emergency lighting and drill observations.
Pathway stepAssistance and PEEP
What must happenPeople who need help receive planned support with dignity.
Evidence or quality testCurrent plans, trained helpers and refuge communication checks.
Pathway stepRefuge if used
What must happenRefuges are protected, communicated with and managed.
Evidence or quality testCommunication test and procedure for escalation.
Pathway stepAssembly
What must happenPeople reach a safe meeting point away from emergency access and smoke.
Evidence or quality testAssembly point review and warden observations.
Pathway stepRoll call or accountability
What must happenThe organisation has a realistic way to identify missing persons without delaying evacuation.
Evidence or quality testVisitor, contractor and staff accountability arrangements.
Pathway stepFire service information
What must happenInformation on hazards, missing persons, isolations and layout is available.
Evidence or quality testPremises information box, site plan or incident controller briefing.
Pathway stepRe-entry control
What must happenNobody returns until authorised by the appropriate person or emergency services.
Evidence or quality testWarden instruction, security control and incident log.
Test the warning under representative operating conditions and ask people at the least favourable positions what they heard, saw and understood; resolve failed coverage before relying on it. Walk each affected route from workface to safety after the phase change. Check it exists, is usable, has appropriate illumination and does not terminate behind a locked gate.
Apply the learning
The signed escape stair has moved and the old route now ends at a locked temporary gate.
Decision and explanation
Hold occupation or work as necessary until the real route, signs, access and briefing are reconciled.
Escape depends on a continuous usable path from where people work to a place of safety. Changes in stairs, hoarding, storage and security can break that path without changing the fire itself. Include visitors, isolated workers and people needing assistance. Route checks and drills should reflect the actual construction phase and result in correction when an assumption fails.
Lesson 15
Know the limits of first response
Fire classes and fire extinguishersFire classes · agent types · dangerous mismatches
Recognise the fuel. Read the extinguisher. Protect your escape.
People and escape first. Raise the alarm, follow the site’s evacuation plan and arrange the emergency call to 999. Only consider a small fire in its earliest stage if you are trained, authorised, have the correct equipment and a clear escape behind you. Smoke, spreading fire, uncertainty or an unsafe approach mean withdraw. Never delay escape to fetch an extinguisher.
UK awareness reference for common and specialist portable extinguisher families. Actual ratings, exclusions and manufacturer instructions govern each unit. Reading this guide is not practical training or permission to fight a fire. Fixed systems, hose reels and specialist industrial firefighting require their own assessed arrangements.
Construction and hot work: an extinguisher at the permit point does not make unsafe hot work or a blocked escape acceptable.
Fire classes: fuel, examples and the important distinction
Class
Fuel and examples
What matters
AClass A
Solid materials
Wood, paper, textiles and many solid plastics.
Usually forms an ember or char bed. Cooling matters; check the marked A rating.
BClass B
Flammable liquids
Petrol, solvents, diesel when burning, and liquefiable solids such as wax.
Fuel can spread across a surface. An unsuitable jet can spread burning liquid; solvent compatibility matters.
CClass C
Flammable gases
Propane, butane or methane.
Not a routine employee firefighting task. Knocking down flame while gas continues to escape can create an explosive cloud. Fuel isolation requires safe, competent action under the emergency plan.
DClass D
Combustible metals
Magnesium, sodium or metallic lithium.
Needs a metal-specific specialist agent. Ordinary ABC powder is not Class D powder.
FClass F
Cooking oils and fats
Hot oil in a fryer or pan.
Very hot oil can reignite. Water can produce violent steam expansion and eject burning oil.
LClass L
Lithium-ion batteries
A lithium-ion tool, e-bike or vehicle battery in thermal runaway.
Class L is included in BS ISO 3941:2026. Toxic or flammable gas, heat propagation and reignition need specialist planning. This is different from a metallic-lithium Class D fire.
Electrical equipment: Energised electrical equipment is an additional hazard, not a UK fire class called E. Do not import US Class C electrical or Class K cooking labels into this UK guide. Isolation, only where safe and authorised, does not remove the burning fuel or stored battery energy. Use the unit’s explicit electrical suitability and limitations.
Class L is the 2026 addition to the classification standard. Existing extinguisher labels and product test claims vary; a new class name does not certify every battery product.
Compare the classes · including lithium-ion batteries
Typical = usual application for the labelled family. If rated / unit limits = confirm the actual label and manufacturer conditions. No = not a normal selection for that hazard; specialist engineered arrangements are separate. This table cannot authorise firefighting.
* Electrical is an additional hazard, not a fire class. Gas-fire and battery-fire response require the assessed specialist plan. Scroll the table sideways on a narrow screen.
Typical portable-agent applications: always confirm the actual unit
Agent family
A · solids
B · liquids
C · gases
D · metals
Electrical*
F · cooking oil
L · Li-ion
Water
Typical
No
No
No
Unit limits
No
No
Water spray / water with additives
Typical
If rated
No
No
Unit limits
No
No
Foam
Typical
Typical
No
No
Unit limits
No
No
Water mist
Typical
If rated
No
No
Unit limits
If rated
Specialist plan
ABC dry powder
Typical
Typical
Specialist plan
No
Unit limits
No
No
BC dry powder
No
Typical
Specialist plan
No
Unit limits
No
No
Class D specialist powder
No
No
No
Exact metal
No
No
No
Carbon dioxide (CO₂)
No
Typical
No
No
Unit limits
No
No
Wet chemical
If rated
If rated
No
No
Unit limits
Typical
No
Clean agent / vaporising liquid
Unit rating
Unit rating
No
No
Unit limits
No
No
Battery-specific suppression products
If rated
No
No
No
Unit limits
No
Specified battery
Extinguisher types: uses and dangers
These are typical applications, not universal permissions. Check the label on the actual unit. Images are photorealistic teaching illustrations inspired by the referenced equipment; they are not photographs or certified product labels. Use Inspect the parts to explore the hardware. Band, nozzle and label details vary.
Common and specialist portable extinguisher families
Type and recognition
Typical rating and use
Wrong use: what can go wrong?
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
WaterRed / WATER marking
Normally A
Cools burning solid material such as paper, wood or fabric.
Check the limitation
Ordinary water is unsuitable for live electrical equipment, flammable-liquid pools, cooking oil and reactive metals: shock, spreading fuel or violent reaction can result.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Water spray / water with additivesUsually red; read the agent name
A; B only if explicitly rated
Improved wetting or spray performance can help on the hazards stated on that model’s label.
Check the limitation
An additive does not make every water extinguisher safe for electricity, oils or reactive chemicals. Check the specific exclusions.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Direct spray nozzle
This compact foam example has a nozzle attached directly to the valve. Larger units may have a hose. Recognise the actual discharge arrangement and use only the approved agent and instructions.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
FoamCream panel / FOAM
Commonly A and B
Cools and forms a surface blanket on suitable liquid fires. The agent must suit the actual fuel; some alcohols need alcohol-resistant foam.
Check the limitation
Ordinary foam is not a general answer for live electricity, cooking oil or metal fires. Unsuitable foam may break down on a solvent; a jet can spread fuel. Free-flowing fuel needs specialist response.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Fine-mist nozzle
The specially designed nozzle creates the intended fine spray. It is not an ordinary water jet. Nozzle appearance alone does not establish any tested electrical suitability.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Water mistManufacturer marking varies
Model-specific; commonly A, some F
Fine droplets absorb heat. Some products have additional ratings or tested electrical suitability, with stated voltage and distance conditions.
Check the limitation
‘Mist’ is not universal approval. Use only the classes and electrical conditions actually declared for that model; do not assume it covers metals, liquids or batteries.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
ABC dry powderBlue panel / ABC POWDER
A, B and C if marked
Interrupts flame chemistry; multipurpose powder also acts on Class A material. A C marking does not authorise tackling a gas leak.
Check the limitation
Powder can obscure escape and impair breathing; it is not generally recommended indoors. Limited cooling allows reignition. It is not metal-specific D powder or a substitute for F-rated cooking-oil equipment.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
BC dry powderBlue panel / BC POWDER
B and C if marked; not A
Selected for particular liquid or gas hazards under the assessed plan. Electrical use must follow the actual unit’s instructions.
Check the limitation
Do not assume all blue powder extinguishers protect wood or paper. It has the visibility, breathing and reignition limitations of powder; it does not provide Class D or F protection.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Specialist low-velocity applicator
The specialist applicator places the compatible metal-fire agent without unnecessarily disturbing burning material. Both agent and application method must suit the specific metal; this is not an ABC powder nozzle.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Class D specialist powderSpecific metal and agent named on label
D, for the specified metal
A specialist powder can isolate or absorb heat from a compatible burning metal. Selection requires knowledge of the metal and its form.
Check the limitation
The wrong powder can fail or react. Water, foam and CO₂ can be dangerous on certain burning metals. A powder suitable for magnesium is not automatically suitable for metallic lithium.
Parts in text
Cylinder
The narrow steel cylinder contains carbon dioxide under pressure. There is normally no pressure gauge on this portable type; service assessment includes the appropriate mass and integrity checks by competent personnel.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Horn and designated insulated grip
The flared horn directs the CO₂ discharge. Discharge parts can become extremely cold. Only the parts identified by the manufacturer as safe to hold should be gripped; not every horn is frost-free.
Displaces the atmosphere around a small flame and leaves no powder residue. Often selected around electrical equipment.
Check the limitation
Poor cooling means reignition is possible. CO₂ can create a dangerous atmosphere in enclosed spaces; discharge can cause frostbite. Hold only the designated insulated parts. Not a cooking-oil or metal-fire substitute.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, lance and spray applicator
The hose feeds the long lance and purpose-designed applicator. It helps distinguish this kitchen-fire unit from an ordinary short-nozzle extinguisher. Use requires model-specific practical training.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Wet chemicalYellow panel / WET CHEMICAL
F; often A if marked
Cools cooking oil and creates a protective surface layer through reaction with the fat. Use only within the actual unit’s rating and instructions.
Check the limitation
Do not mistake it for a general liquid-fire or electrical extinguisher. Incorrect application or moving the fryer can splash hot oil; apparent flame-out does not establish safe temperature.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
Read the actual agent name, fire ratings, electrical warnings and instructions. Colour is a recognition aid; it does not prove suitability. The illustration is not an operating label.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, nozzle or applicator
The flexible hose ends in the model’s discharge nozzle. The clip is for stowage; a hose being clipped in place is not a service check. Do not block, detach or test-discharge it during a visual inspection.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Clean agent / vaporising liquidRead the agent; no universal colour shortcut
Product- and jurisdiction-specific
Specialist low-residue agents may protect sensitive equipment. Confirm the UK-approved application and the manufacturer’s limits.
Check the limitation
Low residue does not mean safe to breathe. Do not copy a US A:B:C rating as UK gas-fire approval. Legacy halon is restricted to permitted critical uses and applicable deadlines.
Parts in text
Cylinder
The pressure vessel holds the agent and propellant as designed. Report corrosion, dents or other damage. Do not open, refill or repair it as an awareness check.
Agent name and colour marking
This generic illustration has a green agent area and boot inspired by the supplied product. Green is not a universal Class L identification code. Read the real product name, chemistry, battery limits and instructions.
Fixed carrying handle
The lower fixed handle supports the unit. It is different from the upper operating lever. The exact grip and operation belong in practical instruction for the model.
Operating / squeeze lever
The upper lever operates the discharge valve when the safety device is released. Do not squeeze or discharge a unit to test it during a routine visual check.
Safety pin and pull ring
The pin mechanically prevents accidental operation. A pin or ring that is missing, distorted or insecure needs reporting; its presence does not prove the unit is serviceable.
Tamper indicator / snap-lock seal
The breakable indicator or snap-lock seal shows possible disturbance. Designs can use a separate pin-retaining strap or a pin-mounted indicator. It is different from the mechanical safety pin and is not a theft lock. Report it if broken or missing.
Pressure gauge
On this stored-pressure example the gauge indicates pressure, not the mass of agent remaining. A pointer in the marked range does not prove the cylinder is full or the unit has passed its service checks.
Hose, grip and applicator
The illustrated hose has a coloured ribbed grip and a small application tip. This shows the hardware family, not a tested battery capability. Follow the instructions for the actual agent and generation.
Base / protective boot
The boot protects the base on this example. Other models have a different foot arrangement or no separate boot. Check the approved mounting and access rather than guessing from the picture.
Battery-specific suppression productsNamed formulation and tested application
Check independent scope and instructions
Some products use water-based cooling or specialist media such as aqueous vermiculite for specified battery scenarios. Selection depends on chemistry, capacity and location.
Check the limitation
A ‘lithium’ label is not proof it will stop thermal runaway in a large pack. Flame suppression may not prevent reignition or gas release. Do not approach, carry or submerge a failing battery as a learner exercise.
Lithium-ion product example · Firechief 6 L Lith-Ex
A named product example helps connect the generic table to an actual unit. Confirm the exact product before using its claims.
Agent and intended application
The linked Seton example uses aqueous vermiculite dispersion (AVD) for specified lithium-ion battery fire applications. Water content cools; the dispersed mineral helps form a barrier. This is not generic Class D metal-fire powder.
Read the actual rating
Seton lists a 6 L product with a 13A rating. That A rating describes its solid-material test performance; it does not, by itself, certify a universal Class L battery capability.
Match the exact model and generation
The manufacturer’s current 6 L G2 page identifies FLE6X and different discharge details from the retailer’s older listing. Do not mix their time, range or pressure values. Match the delivered label, product sheet and manual.
Check the battery scope
Confirm the allowed battery chemistry, energy capacity, state and scenario with the current manufacturer information and competent fire assessment. A large EV or energy-storage pack cannot be treated as a small-device fire.
Electrical conditions are product-specific
The supplied product label includes a voltage and minimum-distance condition. Do not transfer that condition to another battery extinguisher or infer that it makes an unsafe electrical approach acceptable.
After the flame disappears
Heat, off-gas and reignition can remain. Follow the planned withdrawal, exclusion and fire-service response; do not pick up, submerge or return a failed battery to charging.
Read the agent, fire-class letters, performance rating, electrical warnings, operating instructions and service condition. Numbers such as 13A or 55B describe standardised test performance, not a safe room size or permission to tackle that amount of fire. Colour is a clue; the actual label and assessed plan decide suitability.
What about a fire blanket?
A fire blanket is separate equipment, not an extinguisher type. It may be specified for a small contained cooking fire, but safe approach and the manufacturer’s limits still matter. Never carry a burning pan, improvise a cover or put yourself between fire and your exit.
Spot the dangerous assumption
Pause at each question, then open the explanation. These are unscored learning prompts alongside the course assessment.
A pan of cooking oil is burning. Would ordinary water help?
No. Rapid steam production can throw burning oil across the room. Raise the alarm and follow the kitchen emergency plan; never move the pan. Only a trained, authorised person should consider the specified F-rated equipment with a safe escape.
There is a C on the powder extinguisher. Should I put out the leaking gas flame?
Not as a routine response. Unburnt gas may continue escaping and form an explosive cloud. Withdraw, alarm and report the supply involved. Any safe isolation and specialist firefighting must follow the assessed emergency arrangements.
The flame around a battery has disappeared. Is the incident over?
No. Internal heat, flammable or toxic off-gas and reignition can remain. Keep clear, prevent access and tell the fire and rescue service what battery is involved. Flame-out is not permission to handle it or restart charging.
Both extinguishers have blue panels. Are the powders interchangeable?
No. Read ABC, BC or the exact Class D metal specification. Colour identifies a family; it does not establish the correct agent, rating or safe application.
A CO₂ extinguisher leaves no mess. Is it ideal in a small unventilated room?
No. A dangerous CO₂ concentration can incapacitate a person, while the fire and smoke already threaten escape. Do not enter an unsafe room. The fire plan and competent equipment selection must account for the space.
A water-mist product claims electrical suitability. Can I use any water extinguisher on a live cabinet?
No. Any tested electrical claim belongs to that particular model, with its own voltage and distance limits. It does not apply to ordinary water or another mist product, and it does not make an unsafe approach acceptable.
Source guidance and scope
UK learning context. Consult the applicable national fire guidance and your premises’ assessed plan. Manufacturer examples explain product variation; they are not product recommendations. Guidance checked 24 October 2026.
Raise the alarm, withdraw and follow the site's emergency arrangements; only trained safe first response is appropriate.
Read the workface decision
People must not be pressured to fight a developing fire or approach hazardous smoke. Equipment selection and any trained first response depend on the hazard and the ability to remain safe. The first priorities are warning, escape and professional emergency support. Do not interpret possession of an extinguisher as authority to tackle an unknown, growing or specialised fire.
Visual practice · Know the limits of first response
SHAREhub photographic illustration · Fire-safety engineer inspecting a workplace fire alarm control panel. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
People must not be pressured to fight a developing fire or approach hazardous smoke. Equipment selection and any trained first response depend on the hazard and the ability to remain safe. The first priorities are warning, escape and professional emergency support. Do not interpret possession of an extinguisher as authority to tackle an unknown, growing or specialised fire.
Practise a safe emergency message
For this fictional exercise, give the emergency contact a concise message: exact access location, the observed fire or smoke, known battery or gas involvement, people who may be affected and the safe assembly arrangements. Do not delay warning while trying to identify every product. Keep the route clear for others and the emergency services and report missing people through the established process. Nobody should re-enter because a colleague appears to have left belongings behind or because a small flame has disappeared from view.
When must staff leave a fire rather than attempt first-response firefighting?
Raise the alarm and evacuate. A trained person may consider a very limited early response only when the local plan, correct equipment and a clear retreat make it safe. Leave immediately if smoke builds, visibility falls, the fire grows, a cylinder, battery or unknown chemical is involved, the extinguisher is uncertain, or the way out could be cut off.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
Practise a safe emergency message
For this fictional exercise, give the emergency contact a concise message: exact access location, the observed fire or smoke, known battery or gas involvement, people who may be affected and the safe assembly arrangements. Do not delay warning while trying to identify every product. Keep the route clear for others and the emergency services and report missing people through the established process. Nobody should re-enter because a colleague appears to have left belongings behind or because a small flame has disappeared from view.
When must staff leave a fire rather than attempt first-response firefighting?
Raise the alarm and evacuate. A trained person may consider a very limited early response only when the local plan, correct equipment and a clear retreat make it safe.
Leave immediately if smoke builds, visibility falls, the fire grows, a cylinder, battery or unknown chemical is involved, the extinguisher is uncertain, or the way out could be cut off. No worker should be pressed to protect stock or avoid a callout; report the location and hazards to the incident controller from safety.
Do not fight ifFlames are spreading or smoke is building.
ConditionTraining
Fight only ifPerson is trained and confident.
Do not fight ifPerson is unsure or pressured.
ConditionExtinguisher
Fight only ifCorrect media is available.
Do not fight ifFire class is unknown or media could react badly.
ConditionEscape
Fight only ifClear exit remains behind the person.
Do not fight ifFire is between person and exit.
ConditionAtmosphere
Fight only ifSmoke, heat and fumes are minimal.
Do not fight ifBreathing is affected or visibility is poor.
ConditionHazardous contents
Fight only ifNo cylinders, flammables or dangerous substances involved.
Do not fight ifCylinder, solvent, battery or process hazard is present.
Evidence to establish at the workface
Control surrounding fuel, escape routes and charging occupancy. Include credible battery failure in warning and emergency arrangements rather than relying on someone noticing it late.
Apply the learning
A worker encounters growing smoke from a damaged charging battery and is told to stay and fight it.
Decision and explanation
Raise the alarm, withdraw and follow the site's emergency arrangements; only trained safe first response is appropriate.
People must not be pressured to fight a developing fire or approach hazardous smoke. Equipment selection and any trained first response depend on the hazard and the ability to remain safe. The first priorities are warning, escape and professional emergency support. Do not interpret possession of an extinguisher as authority to tackle an unknown, growing or specialised fire.
Lesson 16
Check the fire evidence at handover
Keep the job under the required close-out controls until the relevant checks and handover are confirmed.
Read the workface decision
Close-out needs to address the real fire pathways and the people who receive the area. Evidence should link the job, location, precautions, checks, defects and responsible release. A signed box cannot substitute for an omitted physical check. Good records make the next shift's information better, while a vague completion statement can conceal an unfinished safety task.
Visual practice · Check the fire evidence at handover
Actual SHAREsimulate model capture · Hot work is proposed outside the controlled bay. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Close-out needs to address the real fire pathways and the people who receive the area. Evidence should link the job, location, precautions, checks, defects and responsible release. A signed box cannot substitute for an omitted physical check. Good records make the next shift's information better, while a vague completion statement can conceal an unfinished safety task.
When can an impaired alarm or firefighting measure return to service?
Only after the affected function and its interfaces have been repaired, checked and formally handed back. Name the impaired zone, equipment, affected people and protection function. Before a planned isolation, authorise its boundary and duration, coordinate with occupiers and contractors, control ignition and fuel, and decide whether occupancy or high-hazard work can continue.
Evidence to establish at the workface
Eliminate the hot stage where a technically suitable cold connection or off-site fabrication can achieve the job; check that the alternative does not introduce another uncontrolled hazard.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
When can an impaired alarm or firefighting measure return to service?
Only after the affected function and its interfaces have been repaired, checked and formally handed back.
Name the impaired zone, equipment, affected people and protection function. Before a planned isolation, authorise its boundary and duration, coordinate with occupiers and contractors, control ignition and fuel, and decide whether occupancy or high-hazard work can continue. A patrol is not automatically equivalent to designed detection and warning.
On restoration, a competent person checks the device or system, any monitoring and cause-and-effect interfaces, panel state and remaining overrides. The owner confirms that temporary measures can end and tells the people affected. A normal-looking panel alone is not evidence that every interface works.
Keep the impairment log, decision maker, temporary controls, test evidence, communications and recurrence review. An unexpected defect follows the same immediate risk decision; if warning or escape cannot be made reliable, restrict the area or stop the activity.
Evidence to establish at the workface
Eliminate the hot stage where a technically suitable cold connection or off-site fabrication can achieve the job; check that the alternative does not introduce another uncontrolled hazard.
Apply the learning
The hot-work permit is signed closed but the concealed space check and affected-area handover are missing.
Decision and explanation
Keep the job under the required close-out controls until the relevant checks and handover are confirmed.
Close-out needs to address the real fire pathways and the people who receive the area. Evidence should link the job, location, precautions, checks, defects and responsible release. A signed box cannot substitute for an omitted physical check. Good records make the next shift's information better, while a vague completion statement can conceal an unfinished safety task.
Lesson 17
Capstone: simultaneous work and a moved exit
Hold affected work and coordinate ignition, fuel, warning, escape and emergency arrangements before authorising the new phase.
Read the workface decision
Simultaneous activities can defeat controls that appear adequate when considered alone. The new route may pass the charging point while delivery packaging changes the hot-work fire load. Resolve the interface as a combined workface decision. Assign each correction, verify the layout and brief the people who need to use it before work resumes.
Visual practice · Capstone: simultaneous work and a moved exit
SHAREhub photographic illustration · Office workers assembling safely outside a UK workplace during an evacuation drill. Use the written case for the exercise; this image does not prove a defect or safe system.Read the workface decision
Simultaneous activities can defeat controls that appear adequate when considered alone. The new route may pass the charging point while delivery packaging changes the hot-work fire load. Resolve the interface as a combined workface decision. Assign each correction, verify the layout and brief the people who need to use it before work resumes.
What should a fire emergency plan include?
The plan should describe actions, roles, communications, assistance, shutdowns, information and review. A good plan is specific enough to work on the day. It names roles, deputies, call-out arrangements, assembly points, vulnerable-person support, contractor and visitor arrangements, high-risk areas, fire service information, emergency contacts and post-incident decision routes.
Evidence to establish at the workface
Provide an effective means to discover and communicate fire throughout the occupied site, considering noise, hearing protection, remote work and people who need alternative warning or assistance.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What should a fire emergency plan include?
The plan should describe actions, roles, communications, assistance, shutdowns, information and review.
A good plan is specific enough to work on the day. It names roles, deputies, call-out arrangements, assembly points, vulnerable-person support, contractor and visitor arrangements, high-risk areas, fire service information, emergency contacts and post-incident decision routes.
It should be tested through drills and reviewed after changes, near misses, false alarms, building works, occupancy changes, enforcement findings or lessons from incidents.
Fire emergency plan contents
Plan area
What to define
Evidence
Plan areaAlarm action
What to defineWhat people do when alarm sounds.
EvidenceProcedure and drill record.
Plan areaRoles
What to defineWardens, deputies, incident lead and reception/security roles.
EvidenceRole list and training.
Plan areaVulnerable people
What to definePEEPs or general assistance arrangements.
EvidencePrivate plan and review.
Plan areaShutdowns
What to defineOnly planned safe shutdowns and competent isolation.
EvidenceShutdown instruction.
Plan areaFire service information
What to definePlans, hazards, utilities, access and contacts.
EvidencePremises information pack.
Plan areaRecovery
What to defineWho authorises re-entry and restart.
Provide an effective means to discover and communicate fire throughout the occupied site, considering noise, hearing protection, remote work and people who need alternative warning or assistance.
Apply the learning
Hot work, a charging station and a delivery change coincide with relocation of the temporary stair.
Decision and explanation
Hold affected work and coordinate ignition, fuel, warning, escape and emergency arrangements before authorising the new phase.
Simultaneous activities can defeat controls that appear adequate when considered alone. The new route may pass the charging point while delivery packaging changes the hot-work fire load. Resolve the interface as a combined workface decision. Assign each correction, verify the layout and brief the people who need to use it before work resumes.
Lesson 18
Build a measurable fire improvement
Assign an owner to change storage and delivery arrangements, verify the usable route and define a check when phases change.
Read the workface decision
Learning should produce a usable decision and a better barrier. Select a specific pathway such as obstructed escape, uncontrolled hot work or damaged battery return, and establish what will change. Check implementation in real working conditions. Course completion demonstrates this learning outcome within its scope; specialist fire design, complex assessment and emergency duties require appropriate competence and appointment.
Visual practice · Build a measurable fire improvement
Actual SHAREsimulate model capture · Gas and fuel are proposed outside controlled storage. The exercise description supplies the scenario; a still image cannot establish hidden conditions.Read the workface decision
Learning should produce a usable decision and a better barrier. Select a specific pathway such as obstructed escape, uncontrolled hot work or damaged battery return, and establish what will change. Check implementation in real working conditions. Course completion demonstrates this learning outcome within its scope; specialist fire design, complex assessment and emergency duties require appropriate competence and appointment.
What evidence shows fire risk assessment objectives and competence is controlled?
Evidence should show that fire precautions are suitable, available, maintained, tested, understood and reviewed. Fire evidence should connect the fire risk assessment to real controls. A log book alone is not enough if defects remain open, staff do not know the procedure or equipment cannot be reached during normal work.
Evidence to establish at the workface
Keep ignition and heat sources away from foreseeable releases and maintain usable escape and responder access. Plan transfers and temporary storage so they preserve equivalent controls.
Try the optional visual exercise in the interactive course, then complete the required lesson decision.
What evidence shows fire risk assessment objectives and competence is controlled?
Evidence should show that fire precautions are suitable, available, maintained, tested, understood and reviewed.
Fire evidence should connect the fire risk assessment to real controls. A log book alone is not enough if defects remain open, staff do not know the procedure or equipment cannot be reached during normal work.
Good records show what was checked, what failed, who owned the action, when it was closed and how the responsible person knows the arrangement still protects relevant persons.
Fire Risk Assessment Objectives and Competence evidence pack
Evidence item
What it should show
Assurance question
Evidence itemAssessor competence evidence
What it should showThe assessor's knowledge, experience and limits match the premises.
Assurance questionRecord why the person was suitable and when specialists were used.
Evidence itemSignificant findings
What it should showHazards, people at risk and controls are clear.
Assurance questionFindings are site-specific and actionable.
Evidence itemFRA review record
What it should showReviews are triggered by change, incident, drill learning and defects.
Assurance questionDates, reasons and decisions are recorded.
Evidence itemFire risk assessment
What it should showCurrent hazards, people at risk, existing controls, further actions and review triggers are recorded.
Assurance questionCheck after change, incident, refurbishment, occupancy change or drill learning.
Evidence itemAction tracker
What it should showActions show owner, due date, priority, interim control and close-out evidence.
Assurance questionHigh-risk defects should not drift without escalation.
Evidence itemTesting and inspection records
What it should showAlarms, emergency lighting, extinguishers, doors, escape routes and relevant systems are checked at suitable intervals.
Assurance questionRecords should show defects and corrective action, not just ticks.
Evidence itemTraining and drill records
What it should showWorkers, wardens and relevant contractors know what to do and how to report defects.
Assurance questionDrill observations should lead to improvement.
Keep ignition and heat sources away from foreseeable releases and maintain usable escape and responder access. Plan transfers and temporary storage so they preserve equivalent controls.
Apply the learning
The action list says improve fire awareness but repeated deliveries continue blocking the escape route.
Decision and explanation
Assign an owner to change storage and delivery arrangements, verify the usable route and define a check when phases change.
Learning should produce a usable decision and a better barrier. Select a specific pathway such as obstructed escape, uncontrolled hot work or damaged battery return, and establish what will change. Check implementation in real working conditions. Course completion demonstrates this learning outcome within its scope; specialist fire design, complex assessment and emergency duties require appropriate competence and appointment.
Example emergency response plan
Study a completed fictional industrial construction and commissioning plan. Compare its warning, roles, accountability, responder access, rescue limits and recovery decisions with the learning above. It includes a new fictional site schematic, a worked exercise and separate blank recording annexes.
Use this as a teaching example when developing arrangements for your own premises. The fictional layout and role identifiers are not live emergency instructions.