Lifting operations on construction sites · learning reader

Free training · Approx. 2h–3h · estimated self-paced learning, including activities and assessment.

Public teaching is free without an account. A free learner account is required for confirmed LMS assessment, completion and certificate records. See the full course outline and access routes.

Teaching and applied cases for accessible study. The interactive course records assessed completion.

Lesson 1

Start with the handling need

Assess the whole load journey and remove avoidable exposure before refining the individual lift.

A lift begins before the hook is attached

A lifting operation includes lowering as well as raising. At Foundry Court, delivery, temporary storage, installation and removal can each create a separate movement of a load. Mapping that journey often reveals an avoidable lift, an unnecessary change of lifting equipment or a receiving area that will not support the item. Start with what must be achieved, who can be affected and the safest practicable way to achieve it.

Compare alternatives while the design and programme can still change. Prefabrication, an adjusted delivery position, smaller units or installing from a different level may remove exposure, but each alternative needs its own assessment. Breaking a load into smaller pieces is useful only if the new connections, manual handling, stability and work at height are acceptable. Do not assume that a smaller visible load is automatically the safer operation.

Write the boundary of the exercise: which load, start and landing position, equipment, route and work period are being considered? A course exercise can teach the questions and hold points. It cannot establish the actual mass, ground strength or competence of a live team. Those facts come from the task and the responsible competent people.

Visual practice · Start with the handling need

Lifting accessories being inspected beside a stationary UK overhead crane
SHAREhub photographic illustration · Lifting accessories being inspected beside a stationary UK overhead crane. Use the written case for the exercise; this image does not prove a defect or safe system.
A lift begins before the hook is attached

A lifting operation includes lowering as well as raising. At Foundry Court, delivery, temporary storage, installation and removal can each create a separate movement of a load. Mapping that journey often reveals an avoidable lift, an unnecessary change of lifting equipment or a receiving area that will not support the item. Start with what must be achieved, who can be affected and the safest practicable way to achieve it.

What does load-handling equipment and lifting operations mean?

It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system. This topic sits between manual handling, work equipment, workplace transport and lifting operations. A sack truck, trolley or pallet truck may reduce manual handling effort, but it can introduce new risks such as runaway loads, poor steering, trapping, slopes, unsuitable wheels or overloading.

How can the hierarchy of controls prevent dropped loads and unsafe lifting operations?

Remove the need for hazardous handling where feasible, then select equipment and controls for the residual lift. Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What does load-handling equipment and lifting operations mean?

It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

Best-practice guide · six simple steps

Best-practice guide: Load-Handling Equipment and Lifting Operations

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. What does load-handling equipment and lifting operations mean?

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system.

    • Avoid / redesign: Avoid moving the motor by redesigning work at its current position where feasible.
    • Control the task: Use rated lifting gear, secure attachments and a segregated travel route.
    • Verify before release: Planner records feasibility; unclear task holds lift.

    It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system. Choose a safer way to move the load before designing a lift.

    Apply it: Which part of this plan would you check at the workface before authorising the task?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  2. 2. Turn load-handling equipment and lifting operations knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: Avoid moving the motor by redesigning work at its current position where feasible.
    • Make it observable: Planner records feasibility; unclear task holds lift.
    • Keep useful evidence: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Choose a safer way to move the load before designing a lift. Where lifting equipment is needed, a competent person plans the operation, selects equipment and accessories for the load and environment, keeps people away from a suspended load and verifies pre-use checks, maintenance and statutory examination. Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  3. 3. Worked lifting assessment example

    Fictional example: a practical application of the existing topic lesson.

    • Load: What is being lifted and where is the centre of gravity?
    • Equipment: Is the lift truck and attachment suitable?
    • Route: Can the load travel safely?

    Load: What is being lifted and where is the centre of gravity? Evidence / response: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet. Equipment: Is the lift truck and attachment suitable? Evidence / response: Correct rated capacity, fork length suitable, daily check complete.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  4. 4. Follow the load and the people in its path

    Connect the task, the route to the person and the control that can fail.

    • Load failure: An unsuitable attachment or insecure load can fall or shift.
    • Movement: A swinging load or moving lifting equipment can trap or strike people.
    • Stability: Ground, capacity or setup failures can overturn equipment or destabilise the lift.

    An unsuitable attachment or insecure load can fall or shift. A swinging load or moving lifting equipment can trap or strike people. Ground, capacity or setup failures can overturn equipment or destabilise the lift. Use the full topic for the detailed mechanism, task limits and source scope.

    Apply it: Where is this harm route present in the actual work, and which control breaks it before anyone is exposed?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)
  5. 5. Choose controls for load-handling equipment and lifting operations

    Start with the stronger practicable options and verify their effect.

    • Eliminate: Avoid moving the motor by redesigning work at its current position where feasible.
    • Reduce: Use a lighter modular component or a lower-risk delivery/move method.
    • Isolate: Use rated lifting gear, secure attachments and a segregated travel route.
    • Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication.
    • PPE: Head, foot, hand protection for residual contact hazard.

    Eliminate: Avoid moving the motor by redesigning work at its current position where feasible. Reduce: Use a lighter modular component or a lower-risk delivery/move method. Isolate: Use rated lifting gear, secure attachments and a segregated travel route. Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication. PPE: Head, foot, hand protection for residual contact hazard. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

    Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)
  6. 6. Use the full load-handling equipment and lifting operations lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: LOLER overview
    • Official guidance: Safe use of lifting equipment (L113)
    • Task decision: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

    Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicLOLER overview (Great Britain)Safe use of lifting equipment (L113) (Great Britain)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

This topic sits between manual handling, work equipment, workplace transport and lifting operations. A sack truck, trolley or pallet truck may reduce manual handling effort, but it can introduce new risks such as runaway loads, poor steering, trapping, slopes, unsuitable wheels or overloading. A crane, hoist, lift truck or lifting accessory can remove manual effort but creates higher-energy hazards such as suspended loads, overturning, dropped loads, crushing, striking structures or instability.

The first professional judgement is whether the load needs to be handled at all. Can the task be eliminated, delivered closer to the point of use, split into smaller units, palletised, mechanised, redesigned or completed at a better height? If handling remains, the task, individual, load and environment still matter. If lifting equipment is used, the organisation must also consider suitability, strength, stability, marking, pre-use checks, maintenance, inspection, thorough examination, competent planning and supervision.

For learners, the key is not to memorise equipment names. The useful mental model is: what is the load, how will it move, what could fail, who could be struck, trapped, fall or strain, what prevents the event, and what evidence proves the control is live today?

Lifting Operations and Lifting Equipment Regulations (LOLER) scope depends on what the equipment actually does. HSE’s LOLER overview says simple pallet trucks that raise a load only just clear of the ground, and many conveyors, are outside LOLER but remain subject to the Provision and Use of Work Equipment Regulations (PUWER). HSE L113 identifies high-lift pallet trucks able to raise forks above 300 mm as LOLER examples. Do not assign the LOLER six-/12-month examination cycle to every load-handling aid; first check whether it is lifting equipment within scope.

Equipment or activityWhat it is used forMain risk questions
Sack trucks and trolleysMoving smaller loads over short distances.Is the load stable, route suitable, slope controlled and pushing/pulling force reasonable?
Pallet trucksMoving palletised loads on suitable floors.Is the pallet sound, floor level, load within capacity and pedestrian route controlled?
People-handling aidsReducing manual effort in health and social care or assisted movement.Is the aid suitable for the person, maintained and used by trained workers?
Fork-lift trucksLifting and transporting palletised or compatible loads.Is the operator trained, load secure, route segregated and attachment suitable?
Hoists and lifting accessoriesRaising, lowering or positioning loads.Is the safe working load / working load limit marked, accessory compatible and pre-use check complete?
ConveyorsMoving loads continuously through a process.Are trapping points guarded, emergency stops working and maintenance isolated?
Cranes and complex liftsMoving heavier, unusual or high-risk loads.Is there a competent lifting plan, appointed person, exclusion zone and ground/load assessment?

How can the hierarchy of controls prevent dropped loads and unsafe lifting operations?

Remove the need for hazardous handling where feasible, then select equipment and controls for the residual lift.

Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.

The five levels are elimination, substitution, engineering, administrative controls and PPE. “Discipline” is the sustained inspection, feedback and repair that keeps each selected level effective.

How can the ERICPD hierarchy of controls prevent dropped loads and unsafe lifting operations?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for Load-Handling Equipment and Lifting Operations
Activity and release context
Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.
Full example
Read the activity, checks and hand-back in context
ERICPDFive-level hierarchyMotor-move choiceOwner, proof and stop
EliminateEliminationAvoid moving the motor by redesigning work at its current position where feasible.Planner records feasibility; unclear task holds lift.
ReduceSubstitutionUse a lighter modular component or a lower-risk delivery/move method.Engineering verifies compatibility and mass.
Isolate / ControlEngineering controlsUse rated lifting gear, secure attachments and a segregated travel route.Lift supervisor checks setup; failed rating or attachment stops move.
ControlAdministrative controlsApproved lift plan, signaler, exclusion, weather/ground checks and communication.Supervisor briefs crew; change in route or load triggers hold.
PPEPPEHead, foot, hand protection for residual contact hazard.Selector checks suitability; PPE never justifies entry under load.
DisciplineSustaining all levelsRecord checks, defects, examination, repairs and near misses.Manager verifies hand-back and recurring defect review.

How can the ISO 45001 hierarchy of controls prevent dropped loads and unsafe lifting operations?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for Load-Handling Equipment and Lifting Operations
Activity and release context
Eliminate, Reduce, Isolate, Control, Personal protective equipment (PPE) and Discipline (ERICPD) below maps to the five-level hierarchy for a motor lifted from a workshop bay. HSE lifting overview sets the planning and equipment principles. The supervisor holds the move if load identity, attachment, travel clearance or equipment condition is uncertain.
Full example
Read the activity, checks and hand-back in context
ERICPDFive-level hierarchyMotor-move choiceOwner, proof and stop
EliminateEliminationAvoid moving the motor by redesigning work at its current position where feasible.Planner records feasibility; unclear task holds lift.
ReduceSubstitutionUse a lighter modular component or a lower-risk delivery/move method.Engineering verifies compatibility and mass.
Isolate / ControlEngineering controlsUse rated lifting gear, secure attachments and a segregated travel route.Lift supervisor checks setup; failed rating or attachment stops move.
ControlAdministrative controlsApproved lift plan, signaler, exclusion, weather/ground checks and communication.Supervisor briefs crew; change in route or load triggers hold.
PPEPPEHead, foot, hand protection for residual contact hazard.Selector checks suitability; PPE never justifies entry under load.
DisciplineSustaining all levelsRecord checks, defects, examination, repairs and near misses.Manager verifies hand-back and recurring defect review.

Apply the learning

A delivery team proposes three separate crane transfers because the storage bay was chosen before the installation sequence.

Decision and explanation

Review the complete handling sequence and investigate a suitable delivery or installation arrangement that reduces transfers.

Assess the whole load journey and remove avoidable exposure before refining the individual lift.

Lesson 2

Match responsibilities to the operation

Agree responsibilities explicitly; hiring equipment does not itself provide a suitable lifting plan or site coordination.

Who owns each safety decision?

The lifting planner establishes a practicable method and the assumptions supporting it. Supervision verifies that the actual operation follows that method and has authority to stop it. Operators, slingers and signallers need competence for their own tasks and the equipment and load involved. A single person may fulfil more than one role when competent and the arrangement is suitable; a title on a form is not evidence that this is so.

Crane hire arrangements deserve an explicit interface check. Providing a machine and operator does not automatically transfer all planning responsibilities. Establish in the contract who plans, provides ground and service information, controls the work area, supervises and deals with change. Under a contract lift the supplier may assume specified lifting responsibilities, while the site still has to provide reliable information and coordinate other work.

For a non-routine assembly, ask each participant to explain their role, limits and reporting route. The supervisor should know which change requires the planner to return. The operator must know whose movement instructions to follow and how a stop is raised. A gap between two companies is still a gap in the operation; resolve it before mobilising the load.

Visual practice · Match responsibilities to the operation

Actual SHAREsimulate construction model context: A long load is lifted without a suitable plan
Actual SHAREsimulate model capture · A long load is lifted without a suitable plan. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Investigate 1: Suspended long load

A long load is shown beneath the crane. Its weight and centre of gravity cannot be measured from the image. The case says these are uncertain: resolve the plan and load information before taking the strain.

Investigate 2: Barrier around the lifting area

A barrier outlines the lifting zone. Ask whether the actual load path and affected areas are covered by the plan and exclusion arrangement; a visible rectangle alone does not establish a safe lift.

Investigate 3: Crane structure

The crane is visible beside the load. Capacity, setup and task suitability require current lifting information and competent planning; do not infer them from the model’s scale or appearance.

Who owns each safety decision?

The lifting planner establishes a practicable method and the assumptions supporting it. Supervision verifies that the actual operation follows that method and has authority to stop it. Operators, slingers and signallers need competence for their own tasks and the equipment and load involved. A single person may fulfil more than one role when competent and the arrangement is suitable; a title on a form is not evidence that this is so.

How should lifting operations be planned?

Plan the load, route, equipment, people and failure response before anyone attaches a hook or starts a truck. HSE LOLER overview says lifting operations must be properly planned by a competent person, supervised and carried out safely. For a workshop motor lift, record load mass and centre of gravity, rated capacity, sling angles, attachment points, travel route, floor condition, pedestrian exclusion and who signals and stops the move.

Which legal duties apply to lifting and load handling?

Use the instrument for the work location and verify the actual task, people and equipment. Great Britain and Northern Ireland have distinct primary and management law. Equipment-specific rules apply only when the equipment and activity fall within their scope; guidance helps make the practical decision.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should lifting operations be planned?

Plan the load, route, equipment, people and failure response before anyone attaches a hook or starts a truck.

HSE LOLER overview says lifting operations must be properly planned by a competent person, supervised and carried out safely. For a workshop motor lift, record load mass and centre of gravity, rated capacity, sling angles, attachment points, travel route, floor condition, pedestrian exclusion and who signals and stops the move.

The lift plan should be proportionate: a routine well-controlled pallet lift may use a standard method, while an unusual, fragile, tandem or people-lifting operation needs more detailed competent planning. A change in load, ground, weather, equipment or people reopens the plan.

CheckRelease evidenceHold triggerDirect source
Load and routeKnown mass/centre, stable path, exclusion of people.Unknown mass or pedestrian interface.HSE LOLER
EquipmentRated lift/accessories, compatible attachments and pre-use condition.Damaged sling, missing mark or inadequate capacity.HSE equipment selection
PeopleCompetent operator/signaller and supervisor proportionate to task.Unclear signalling or unbriefed change.HSE lift planning

Which legal duties apply to lifting and load handling?

Use the instrument for the work location and verify the actual task, people and equipment.

Great Britain and Northern Ireland have distinct primary and management law. Equipment-specific rules apply only when the equipment and activity fall within their scope; guidance helps make the practical decision.

JurisdictionDirect instrument or guidanceOperational decision supported
Great BritainHealth and Safety at Work etc. Act 1974General duties.
Northern IrelandHealth and Safety at Work (NI) Order 1978Separate NI general duties.
Great BritainManagement Regulations 1999Risk assessment and arrangements.
Northern IrelandManagement Regulations (NI) 2000Separate NI risk and management route.
Great BritainLOLER 1998Planning, suitability and thorough examination of GB lifting equipment.
Northern IrelandLOLER (NI) 1999Separate NI lifting-equipment instrument.
Great BritainPUWER 1998General suitability and maintenance of work equipment.
Northern IrelandPUWER (NI) 1999Separate NI work-equipment route.

Handling aids excluded from LOLER can still need PUWER and manual-handling assessment. Use the Manual Handling Operations Regulations 1992 for GB and the separate NI 1992 manual-handling instrument as applicable. Assess residual push/pull effort, route, gradient, wheel condition, stopping force and the actual users; deciding “not LOLER” does not settle suitability. Sources: HSE push/pull assessment and RAPP; HSENI manual handling.

Apply the learning

The site assumes the crane operator will design the lift; the hire booking provides only the crane and operator.

Decision and explanation

Resolve the hire responsibilities and appoint the competent planning and supervision needed for this lift.

Agree responsibilities explicitly; hiring equipment does not itself provide a suitable lifting plan or site coordination.

Lesson 3

Establish the load, including what cannot be seen

Resolve load uncertainty before tensioning an unverified system; a larger crane cannot prove the load or its attachments.

Mass, centre of gravity and integrity are planning inputs

A fabricated assembly may contain temporary bracing, lifting frames, stored materials or retained fluids that were not included in an early drawing. Establish the actual load in its lifting condition from defensible information. Identify the centre of gravity and how it could move: an unbalanced internal component or liquid can make a load behave differently from a neat rectangular outline.

The load must be strong enough to withstand the chosen handling arrangement. Designated lifting points need the appropriate rating, condition and intended direction of loading. A hole, bracket or convenient pipe is not a lifting point simply because a shackle fits through it. Packaging and transport restraints may hold an item on a vehicle without being suitable for lifting it.

Keep the load supported while uncertainty is resolved. A trial lift within a verified plan can confirm balance and behaviour; it is not a way to discover an unknown mass or prove an unverified attachment. If unexpected resistance occurs, stop safely and investigate. Pulling harder may overload the system, release a hidden connection suddenly or damage the load before anyone sees the cause.

Visual practice · Establish the load, including what cannot be seen

Lifting accessories being inspected beside a stationary UK overhead crane
SHAREhub photographic illustration · Lifting accessories being inspected beside a stationary UK overhead crane. Use the written case for the exercise; this image does not prove a defect or safe system.
Mass, centre of gravity and integrity are planning inputs

A fabricated assembly may contain temporary bracing, lifting frames, stored materials or retained fluids that were not included in an early drawing. Establish the actual load in its lifting condition from defensible information. Identify the centre of gravity and how it could move: an unbalanced internal component or liquid can make a load behave differently from a neat rectangular outline.

How should a motor lift change when the load is not as expected?

A routine method covers only the load, equipment and conditions for which it was assessed. When the item, attachment, centre of gravity or route changes, a competent planner must determine whether the original plan still works. A lifting machine’s maximum marked capacity is not a universal capacity for every position or configuration.

How harm develops in the linked model

An unstable load, overload or uncontrolled movement can strike, crush or overturn equipment and affect people beyond the immediate lift.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should a motor lift change when the load is not as expected?

A routine method covers only the load, equipment and conditions for which it was assessed. When the item, attachment, centre of gravity or route changes, a competent planner must determine whether the original plan still works. A lifting machine’s maximum marked capacity is not a universal capacity for every position or configuration. Related guidance: LOLER overview.

In an illustrative workshop, a motor due for removal is still attached to a base and contains components absent from the old drawing. The supervisor holds the lift before tensioning the rigging. The planner establishes the actual mass, centre of gravity, attachment points and condition from defensible information. A trial lift is not a method of discovering an unknown mass or testing an unverified attachment. Related guidance: LOLER overview.

The planner checks the selected machine and accessories against the load and rated configuration, including load distribution, accessory geometry, capacity reductions, reach and stability as relevant. Equipment instructions and competent technical advice govern the actual arrangement; no universal sling-angle calculation or lifting-point capacity is supplied here. Do not assume an eye or convenient pipe is a rated lifting point. Related guidance: LOLER overview.

The route includes the floor, receiving position, overhead/side clearances and exclusion of people. Establish where the item will be supported before removing accessories and how the team communicates during the move. A changed receiving area or unexpected movement holds the operation for a competent revised decision. Keep people out of the falling-load and trapping routes; nobody goes beneath the suspended load to correct alignment. Related guidance: LOLER overview.

Before release, the supervisor checks that the agreed plan, equipment and team match the actual setup. At completion, establish that the motor is stable and the work area is safe before removing the boundary. Record changed assumptions, equipment defects and the hand-back state. A routine pallet-handling authorisation does not by itself establish competence for this non-routine suspended motor lift. Related guidance: LOLER overview.

Guidance for these decisions: LOLER overview; Safe lifting by machine; Safe use of lifting equipment (L113). Apply the legal route for the work location; illustrative scenarios are SHARE teaching examples.

Apply the learning

The lifting drawing excludes an attached base and nobody can confirm whether the skid contains water.

Decision and explanation

Hold the operation while actual mass, contents, centre of gravity and rated attachment arrangements are established.

Resolve load uncertainty before tensioning an unverified system; a larger crane cannot prove the load or its attachments.

Lesson 4

Read a lift plan as connected assumptions

The whole load and its foreseeable movement must fit the route; people must not compensate by entering trapping positions.

Model practice: follow the full load route

The plan should connect the load to the machine configuration, accessories, ground, movement route and landing arrangement. Read it forwards from preparation and backwards from a safely supported final load. Can the team attach, move, land and detach without anyone entering an uncontrolled falling-load or trapping area? A good plan makes those transitions visible.

The model contains a long load near a crane. The visible geometry is a prompt for enquiry, not a load calculation. Identify rotation and swing, changes of radius, nearby people and the planned receiving position. A route can be suitable for the hook but unsuitable for the ends of a long assembly. Trace the whole load envelope, including rigging, rather than drawing a narrow line between two points.

Work through the five model decisions, then return to distinguish observed conditions from evidence still needed. A screenshot can show a barrier or outrigger location. It cannot show the verified mass, allowable bearing pressure, current weather limit or team competence. Record those as matters to confirm through the actual planning process, rather than declaring them safe because the illustrative scene looks orderly.

Visual practice · Read a lift plan as connected assumptions

Actual SHAREsimulate construction model context: A long load is lifted without a suitable plan
Actual SHAREsimulate model capture · A long load is lifted without a suitable plan. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Model practice: follow the full load route

The plan should connect the load to the machine configuration, accessories, ground, movement route and landing arrangement. Read it forwards from preparation and backwards from a safely supported final load. Can the team attach, move, land and detach without anyone entering an uncontrolled falling-load or trapping area? A good plan makes those transitions visible.

What technical lifting details should learners understand?

A good lift plan turns physical facts into safe decisions before the load leaves the ground. LOLER planning should start with a simple hierarchy: avoid the lift if possible, reduce the amount of handling, choose suitable lifting equipment, plan the lift by competent people, establish the load and route, control the area, execute the lift under supervision, then inspect, examine and learn from defects or near misses. The higher the uncertainty, the more the plan needs engineering judgement rather than habit.

How harm develops in the linked model

An unstable load, overload or uncontrolled movement can strike, crush or overturn equipment and affect people beyond the immediate lift.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What technical lifting details should learners understand?

A good lift plan turns physical facts into safe decisions before the load leaves the ground.

LOLER planning should start with a simple hierarchy: avoid the lift if possible, reduce the amount of handling, choose suitable lifting equipment, plan the lift by competent people, establish the load and route, control the area, execute the lift under supervision, then inspect, examine and learn from defects or near misses. The higher the uncertainty, the more the plan needs engineering judgement rather than habit.

The most common serious failures are not mysterious. A load is heavier than assumed, the centre of gravity is not where people expect, the accessory angle reduces capacity, the ground cannot take outrigger loading, pedestrians enter the lift zone, weather changes, a blind lift relies on weak communication, or a damaged sling stays in use because nobody quarantined it. Learners should read a lifting plan as a chain of assumptions that all need evidence.

A professional lifting assessment should therefore make the invisible parts visible: how the load weight was confirmed, how the centre of gravity was understood, how stability will be maintained, which lifting points are rated, which accessory has been selected and why, what the ground can support, who owns exclusion zones and what evidence proves the equipment remains safe to use.

HSE’s LOLER planning guidance supports competent planning, suitable equipment, supervision and safe execution. Confirm load mass and centre of gravity, sling configuration and rated capacity, ground support for outriggers where relevant, and a clear signaller/operator arrangement before releasing a non-routine lift.

RoleTypical contributionEvidence of competence or control
Appointed personPlans complex or higher-risk lifting operations, selects lift method and confirms controls are suitable.Appointment, lift plan, calculation or method review and experience record.
Lift supervisorControls the lift on site and checks that the plan is followed in real conditions.Briefing record, field checks, stop-work decisions and supervision evidence.
Slinger-signallerAttaches the load, selects or confirms accessories, signals and protects communication.Training, authorisation, observed competence and accessory pre-use checks.
OperatorOperates crane, lift truck, hoist or other lifting equipment within limits.Training, authorisation, daily check and equipment-specific competence.
Banksman or traffic marshalControls vehicle movement and interface where lifting and transport overlap.Role briefing, communication plan and site traffic control.
Competent examinerCarries out statutory thorough examination or specialist inspection.Report of thorough examination, defect grading and close-out evidence.
Site or operations managerProvides resources, time, ground preparation, exclusion-zone authority and contractor coordination.Lift coordination record, simultaneous operations review and action close-out.
Technical issueWhy it mattersWhat good looks like
Load weightCapacity decisions are meaningless if the load weight is guessed.Weight confirmed from drawings, delivery data, weighbridge, markings or competent calculation.
Centre of gravityAn off-centre load can tilt, rotate, overload one leg of a sling or strike nearby people.Lift points, trial lift and rigging arrangement account for the actual balance point.
Load stabilityLoose, flexible, liquid, live or poorly packaged loads can shift during lifting.Load secured, contained, levelled and lifted using a method suited to its behaviour.
Lifting accessory angleSling angle can significantly increase leg tension and reduce effective capacity.Angles are planned, working load limit / safe working load is suitable and spreader beams are used where needed.
Ground bearing and supportCranes, outriggers, MEWPs and lift trucks can overturn or sink where support is poor.Ground assessment, mats, bearing pressure checks and exclusion from voids or excavations.
Exclusion zonesPeople under, beside or near a suspended load can be struck, trapped or crushed.Physical control, clear ownership, no lift over people and active supervision.
Weather and environmentWind, visibility, rain, ice, slope, lighting or overhead services can invalidate the plan.Defined limits, weather checks, route control and stop criteria.
CommunicationBlind lifts and noisy areas make signals and commands safety-critical.Agreed signals, radios if needed, single point of command and emergency stop word.
AccessoryUsed forSelection mistake to avoid
Webbing slingGeneral loads where soft contact reduces damage.Using on sharp edges without protection or with illegible identification tag.
Chain slingRobust lifting, hot or abrasive environments and certain engineered loads.Ignoring angle, shortening method, hook latch damage or chain wear.
Wire rope slingHeavier or industrial lifting where wire rope properties suit the load.Using kinked, crushed, corroded or bird-caged rope.
ShackleConnecting sling, hook, lifting point or accessory.Wrong pin type, side loading, missing markings or no compatibility check.
Spreader or lifting beamControls sling angle or supports long/fragile loads.Using without verifying beam rating, connection points and centre of gravity.
Clamp, magnet or vacuum lifterSpecialist handling of plates, sheets or smooth materials.Using on unsuitable surface, wrong orientation or without fail-safe checks.
Fork attachmentAdapts lift-truck forks for specific loads.Using uncertified attachments, reducing capacity unknowingly or failing to secure attachment.
FindingWhy it mattersExpected action
Missing or illegible sling tagCapacity, identity and inspection status cannot be confirmed.Remove from service, quarantine and replace or seek competent decision.
Damaged hook latch or bent hookLoad may detach or hook strength may be compromised.Stop use, tag out and refer for competent inspection.
Cracked shackle or damaged pin threadConnection may fail under load.Quarantine immediately and record defect.
Lift truck hydraulic leak or brake faultControl of the load may be lost.Remove from service until repaired and verified.
Failed thorough examination itemStatutory examination has identified a defect or restriction.Follow report timescale, prevent use where required and keep close-out evidence.
Overload, shock load or dropped load eventEquipment may be damaged even if no defect is obvious.Stop, isolate, investigate and arrange exceptional examination if needed.

Apply the learning

A long assembly is proposed for a route between the crane and a scaffold, but the plan shows only the hook path.

Decision and explanation

Hold release until the competent plan covers the full load envelope, configuration, people controls and stable landing.

The whole load and its foreseeable movement must fit the route; people must not compensate by entering trapping positions.

Lesson 5

Select machinery for the actual configuration

Suitability follows the actual load, configuration and route; a headline rating cannot establish the permitted operation.

Headline capacity is not the task capacity

Capacity depends on the equipment and its configuration. For a crane, radius, boom configuration, support arrangement and manufacturer limits matter. For a telehandler or other lifting machine, reach, attachment and load position may change the allowable load. Use the applicable information for the proposed setup, including the weight of rigging or attachments where required by the equipment instructions and plan.

Do not extend this course into an improvised lifting calculation. The learner's job is to recognise missing inputs and refer them to the competent planner. A plan that states only the machine's maximum advertised capacity has not demonstrated suitability at the most demanding point of travel. Capacity checks must cover the full operation, not simply the pickup position.

Check compatibility as well as capacity: the accessory must suit the hook or attachment, the lift points, the load surface and the environment. A change of lifting beam, attachment or crane position can alter several assumptions together. Keep the load supported and get the relevant checks updated before accepting a substitute, even if the replacement appears stronger.

Visual practice · Select machinery for the actual configuration

Lifting accessories being inspected beside a stationary UK overhead crane
SHAREhub photographic illustration · Lifting accessories being inspected beside a stationary UK overhead crane. Use the written case for the exercise; this image does not prove a defect or safe system.
Headline capacity is not the task capacity

Capacity depends on the equipment and its configuration. For a crane, radius, boom configuration, support arrangement and manufacturer limits matter. For a telehandler or other lifting machine, reach, attachment and load position may change the allowable load. Use the applicable information for the proposed setup, including the weight of rigging or attachments where required by the equipment instructions and plan.

Turn load-handling equipment and lifting operations knowledge into a decision

Use the evidence to improve the actual work arrangement. Change at source: Avoid moving the motor by redesigning work at its current position where feasible. Make it observable: Planner records feasibility; unclear task holds lift.

How harm develops in the linked model

An unstable load, overload or uncontrolled movement can strike, crush or overturn equipment and affect people beyond the immediate lift.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Turn load-handling equipment and lifting operations knowledge into a decision

Use the evidence to improve the actual work arrangement. Change at source: Avoid moving the motor by redesigning work at its current position where feasible. Make it observable: Planner records feasibility; unclear task holds lift.

Keep useful evidence: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet. Choose a safer way to move the load before designing a lift. Where lifting equipment is needed, a competent person plans the operation, selects equipment and accessories for the load and environment, keeps people away from a suspended load and verifies pre-use checks, maintenance and statutory examination.

Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet. Apply it: What evidence would show that the change improves this task, rather than only completing a record?

Apply the learning

A replacement crane has a larger maximum capacity, but its configuration and capacity at the planned radius have not been checked.

Decision and explanation

Have the competent planner verify the replacement through the complete operation and update the method as needed.

Suitability follows the actual load, configuration and route; a headline rating cannot establish the permitted operation.

Lesson 6

Provide stable ground and support

Ground suitability is location and load specific. A changed bearing needs a competent decision before the crane is loaded.

Model practice: what is beneath the outrigger?

A crane may overturn when support beneath an outrigger fails even though the suspended load is within the machine's lifting capacity. Assess the whole support path: imposed loads, mats or engineered platform, near-surface condition and what lies below. Made ground, recent trenches, cellars, drains and service chambers can matter. A hard-looking surface or a photograph does not establish bearing capacity.

Information must reach the people selecting and setting up the crane. Clarify who provides ground investigation, who assesses the lifting platform and who verifies that the machine stands in the assessed location. Suitable mats spread load only within the designed arrangement; timber or a plate chosen by appearance does not establish a safe bearing system.

In the model, investigate the outrigger beside unverified ground. Compare the proposed bearing with nearby excavations and underground features. Maintain the hold until the competent support arrangement matches the actual setup. Rain, settlement, a relocated crane or a new adjacent excavation can invalidate the original basis. During the operation, unexpected movement is a stop signal, not a cue to pack underneath a loaded outrigger.

Visual practice · Provide stable ground and support

Actual SHAREsimulate construction model context: An outrigger bears on unverified ground
Actual SHAREsimulate model capture · An outrigger bears on unverified ground. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Model practice: what is beneath the outrigger?

A crane may overturn when support beneath an outrigger fails even though the suspended load is within the machine's lifting capacity. Assess the whole support path: imposed loads, mats or engineered platform, near-surface condition and what lies below. Made ground, recent trenches, cellars, drains and service chambers can matter. A hard-looking surface or a photograph does not establish bearing capacity.

Follow the load and the people in its path

Connect the task, the route to the person and the control that can fail. Load failure: An unsuitable attachment or insecure load can fall or shift. Movement: A swinging load or moving lifting equipment can trap or strike people.

How harm develops in the linked model

Concentrated support loads can fail the ground or services and overturn the crane; a visible mat does not prove adequate bearing.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Follow the load and the people in its path

Connect the task, the route to the person and the control that can fail. Load failure: An unsuitable attachment or insecure load can fall or shift. Movement: A swinging load or moving lifting equipment can trap or strike people.

Stability: Ground, capacity or setup failures can overturn equipment or destabilise the lift. An unsuitable attachment or insecure load can fall or shift. A swinging load or moving lifting equipment can trap or strike people.

Ground, capacity or setup failures can overturn equipment or destabilise the lift. Use the full topic for the detailed mechanism, task limits and source scope. Apply it: Where is this harm route present in the actual work, and which control breaks it before anyone is exposed?

Apply the learning

The crane is moved a few metres so an outrigger now stands over a reinstated service trench.

Decision and explanation

Keep the lift stopped and obtain competent verification of the revised ground, support and setup.

Ground suitability is location and load specific. A changed bearing needs a competent decision before the crane is loaded.

Lesson 7

Choose and connect lifting accessories

Accessories must be selected as a compatible arrangement for the actual geometry and conditions, following competent planning and instructions.

Protect the load path from hook to attachment

The rigging arrangement is a system. Each sling, shackle, hook, lifting beam and attachment must suit the intended load and connection. Capacity can change with sling angle, hitch, uneven load distribution, temperature or other conditions specified by the manufacturer. Read the applicable markings and instructions; a colour alone is not sufficient identification.

Protect accessories from sharp edges, crushing and unsuitable bending. Check that connectors seat correctly and that hooks and safety devices can perform their intended function. The rigging method should control load stability without placing hands into pinch points or requiring someone to stand beneath the item. Plan attachment and detachment while the load is supported.

A substitute sling may alter the geometry even when its marked capacity appears adequate. The competent team should verify the complete arrangement rather than swapping one item in isolation. If identity, capacity or condition cannot be established, hold and quarantine the item through the site system. Segregation prevents another crew from selecting it while the technical question is being resolved.

Visual practice · Choose and connect lifting accessories

Lifting accessories being inspected beside a stationary UK overhead crane
SHAREhub photographic illustration · Lifting accessories being inspected beside a stationary UK overhead crane. Use the written case for the exercise; this image does not prove a defect or safe system.
Protect the load path from hook to attachment

The rigging arrangement is a system. Each sling, shackle, hook, lifting beam and attachment must suit the intended load and connection. Capacity can change with sling angle, hitch, uneven load distribution, temperature or other conditions specified by the manufacturer. Read the applicable markings and instructions; a colour alone is not sufficient identification.

Choose controls for load-handling equipment and lifting operations

Start with the stronger practicable options and verify their effect. Eliminate: Avoid moving the motor by redesigning work at its current position where feasible. Reduce: Use a lighter modular component or a lower-risk delivery/move method.

How harm develops in the linked model

A defective or unsuitable accessory can fail and drop the load; examination does not replace pre-use checks or proper selection.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Choose controls for load-handling equipment and lifting operations

Start with the stronger practicable options and verify their effect. Eliminate: Avoid moving the motor by redesigning work at its current position where feasible. Reduce: Use a lighter modular component or a lower-risk delivery/move method.

Isolate: Use rated lifting gear, secure attachments and a segregated travel route. Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication. PPE: Head, foot, hand protection for residual contact hazard.

Eliminate: Avoid moving the motor by redesigning work at its current position where feasible. Reduce: Use a lighter modular component or a lower-risk delivery/move method. Isolate: Use rated lifting gear, secure attachments and a segregated travel route.

Control: Approved lift plan, signaler, exclusion, weather/ground checks and communication. PPE: Head, foot, hand protection for residual contact hazard. Read the full control table for qualifications, ownership and verification.

Use the actual task and applicable jurisdiction; existing technical approval remains unchanged. Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

Apply the learning

A longer sling is substituted to reach an awkward lifting point, changing the rigging geometry.

Decision and explanation

Hold the operation until the competent team verifies the revised arrangement, capacity, protection and connections.

Accessories must be selected as a compatible arrangement for the actual geometry and conditions, following competent planning and instructions.

Lesson 8

Separate checks, maintenance and thorough examination

Current damage overrides administrative reassurance. Quarantine and verify recovery through the competent defect process.

Model practice: a report cannot repair a sling

A pre-use check asks whether the item shows a problem now. Maintenance keeps equipment in suitable condition. A thorough examination is a specialist assessment at the appropriate time and scope. These duties support one another; none is a substitute for the others. An examination report needs to match the actual asset or accessory, not a similar item from the same hire order.

Read the findings, due date and any restrictions. Do not treat a future examination date as a guarantee that damage cannot arise before then. A cut sling, distorted shackle or cracked component stays out of use while competent people determine the appropriate response. The user must prevent further selection and ensure a replacement is suitable for the whole lifting arrangement.

In the model, inspect the stated damage and unclear examination identity. The decision is to secure the situation, report the defect and establish suitable equipment and evidence before release. Do not ask a learner to demonstrate a suspect sling under load. A safe training exercise uses photographs, records or an independently assessed setup; the workface is not a test rig for damaged lifting gear.

Visual practice · Separate checks, maintenance and thorough examination

Actual SHAREsimulate construction model context: Damaged slings and an unclear examination record
Actual SHAREsimulate model capture · Damaged slings and an unclear examination record. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Model practice: a report cannot repair a sling

A pre-use check asks whether the item shows a problem now. Maintenance keeps equipment in suitable condition. A thorough examination is a specialist assessment at the appropriate time and scope. These duties support one another; none is a substitute for the others. An examination report needs to match the actual asset or accessory, not a similar item from the same hire order.

What checks, inspections and examinations are needed?

Pre-use checks, maintenance and LOLER thorough examination answer different questions. HSE thorough-examination guidance says that, without a competent examination scheme specifying another interval, equipment and accessories lifting people and all lifting accessories are examined every six months, while other lifting equipment is examined every 12 months. Examination may also be needed after installation/assembly or exceptional circumstances.

Why does a satisfactory examination report not release every lifting task?

Examination, maintenance, user checks and lift planning answer different questions. A thorough examination records the competent examiner’s findings within its scope and date. It does not select the machine for today’s load, establish the floor condition or prove that the current rigging arrangement is correct.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What checks, inspections and examinations are needed?

Pre-use checks, maintenance and LOLER thorough examination answer different questions.

HSE thorough-examination guidance says that, without a competent examination scheme specifying another interval, equipment and accessories lifting people and all lifting accessories are examined every six months, while other lifting equipment is examined every 12 months. Examination may also be needed after installation/assembly or exceptional circumstances. Serious defects need immediate dutyholder notification and documented removal from use.

The operator still checks the sling, hook, controls and condition before each use. Maintenance prevents deterioration; the competent examiner independently assesses safety-critical condition. Do not use an in-date examination report to override a cracked hook or changed configuration.

AssuranceWhen/whatFailure actionDirect source
Pre-useTask and visible condition before operation.Tag out damaged kit.HSE lifting overview
Thorough examinationSix months for people-lifting equipment/accessories; six for all lifting accessories; 12 for other lifting equipment, unless competent scheme.Withdraw on dangerous defect and notify as required.HSE examination intervals
After exceptional eventRe-examine after damage, critical repair or other jeopardising event.Do not hand back until competent release.HSE exceptional circumstances

Under the applicable LOLER regulation 10 route, the examiner immediately notifies the user of a defect that is or could become dangerous and supplies the required written report. Where the examiner considers there is an existing or imminent risk of serious personal injury, a copy goes to the relevant enforcing authority; immediate repair does not erase that reporting duty. The dutyholder separately quarantines, repairs and verifies recovery before release. Use the GB or NI instrument and enforcing authority applicable to the installation. Sources: HSE lifting examinations and defects.

Why does a satisfactory examination report not release every lifting task?

Examination, maintenance, user checks and lift planning answer different questions. A thorough examination records the competent examiner’s findings within its scope and date. It does not select the machine for today’s load, establish the floor condition or prove that the current rigging arrangement is correct. Related guidance: Thorough examination of lifting equipment.

Match the report to the actual asset and accessories and read defects, due dates and any examination scheme. A report for a similar hoist or an accessory with a different identity is not evidence for the item being used. A serious defect needs the response required by the applicable law and competent examiner, not an administrative extension because replacement equipment is late. Related guidance: Thorough examination of lifting equipment.

A newly damaged sling remains held even if its next periodic examination is months away. Conversely, ordinary maintenance is not itself the statutory thorough examination. Where exceptional damage, failure, installation or other circumstances raise an examination requirement, obtain the competent decision for that equipment and applicable legal route before relying on it. Related guidance: Thorough examination of lifting equipment.

The person undertaking examination needs the relevant theoretical and practical equipment competence and sufficient independence and impartiality. HSE distinguishes this role from the person doing routine maintenance to avoid assessing their own maintenance. Do not treat an employer job title as evidence of that competence. Record the actual report, defect response and equipment release; separately verify the task-specific lift plan. Related guidance: Thorough examination of lifting equipment.

Guidance for these decisions: Thorough examination of lifting equipment; LOLER overview; Safe lifting by machine. Apply the legal route for the work location; illustrative scenarios are SHARE teaching examples.

Apply the learning

A sling has visible cuts, but its examination label is in date and the replacement is delayed.

Decision and explanation

Remove the damaged sling from use and obtain suitable verified replacement equipment before the lift.

Current damage overrides administrative reassurance. Quarantine and verify recovery through the competent defect process.

Lesson 9

Exclude people through the complete movement

Effective exclusion covers the foreseeable load and machinery danger area through pickup, travel and landing.

The danger zone moves with the operation

Plan to avoid lifting over occupied areas wherever practicable. Consider the pickup, travel, possible swing, slewing machinery, landing and removal of accessories. An exclusion boundary drawn around the crane base may leave the receiving crew, adjacent trades or pedestrians exposed elsewhere. The people-control arrangement has to follow the operation through every phase.

Barriers need workable access arrangements. Provide a safe alternative route, coordinate deliveries and tell affected supervisors when an area becomes unavailable. A signaller should not have to leave a safe position to chase people away while also directing the operator. Public protection, neighbouring premises and off-site exposure belong in the same planning discussion when the load or machine could affect them.

Keep people out of trapping positions between the load and fixed structures. Where planned use of a tag line or other control is appropriate, the method must avoid entanglement and keep the user in a safe position. Nobody should guide a heavy suspended item by reaching underneath it. If the intended safe position is unavailable, stop and change the arrangement rather than accepting the gap as part of the job.

Visual practice · Exclude people through the complete movement

Lifting accessories being inspected beside a stationary UK overhead crane
SHAREhub photographic illustration · Lifting accessories being inspected beside a stationary UK overhead crane. Use the written case for the exercise; this image does not prove a defect or safe system.
The danger zone moves with the operation

Plan to avoid lifting over occupied areas wherever practicable. Consider the pickup, travel, possible swing, slewing machinery, landing and removal of accessories. An exclusion boundary drawn around the crane base may leave the receiving crew, adjacent trades or pedestrians exposed elsewhere. The people-control arrangement has to follow the operation through every phase.

Worked lifting assessment example

Fictional example: a practical application of the existing topic lesson. Load: What is being lifted and where is the centre of gravity? Equipment: Is the lift truck and attachment suitable?

How harm develops in the linked model

People can be struck or crushed by a falling or swinging load; the hook and accessories can also strike them.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Worked lifting assessment example

Fictional example: a practical application of the existing topic lesson. Load: What is being lifted and where is the centre of gravity? Equipment: Is the lift truck and attachment suitable?

Route: Can the load travel safely? Load: What is being lifted and where is the centre of gravity? Evidence / response: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.

Equipment: Is the lift truck and attachment suitable? Evidence / response: Correct rated capacity, fork length suitable, daily check complete. Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

Apply the learning

The crane’s base is fenced, but the long load will travel outside that fence across a live access route.

Decision and explanation

Replan or control the whole route and receiving area, with safe alternative access and verified exclusion before movement.

Effective exclusion covers the foreseeable load and machinery danger area through pickup, travel and landing.

Lesson 10

Use clear signalling and safe positions

Loss of the agreed communication is a stop trigger; unplanned signals or assumptions cannot guide a blind load.

A blind move needs a deliberate communication system

Agree how movement instructions will reach the operator, who has authority to give them and how anyone can raise an emergency stop. Use trained people, a suitable agreed signalling method and equipment that works in the actual environment. The system should address background noise, blind areas, radio coverage, language and the safe position of the signaller.

An operator who loses the agreed signal or communication stops safely under the method; guessing the next movement defeats the purpose of controlled signalling. Handover between signallers must be explicit. Several people giving ordinary movement instructions at once creates ambiguity, while an emergency stop must be understood and acted on regardless of who first identifies the danger.

Briefing is demonstrated by understanding rather than attendance alone. Ask the operator and signaller to describe the same stop response and identify where the load becomes obscured. Check that the signaller can see the relevant area without standing in a swing or crushing zone. If visibility or communication cannot be provided as planned, involve the competent planning team before continuing.

Visual practice · Use clear signalling and safe positions

Actual SHAREsimulate construction model context: A proposed lift crosses an occupied walkway
Actual SHAREsimulate model capture · A proposed lift crosses an occupied walkway. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
A blind move needs a deliberate communication system

Agree how movement instructions will reach the operator, who has authority to give them and how anyone can raise an emergency stop. Use trained people, a suitable agreed signalling method and equipment that works in the actual environment. The system should address background noise, blind areas, radio coverage, language and the safe position of the signaller.

Use the full load-handling equipment and lifting operations lesson

Follow the official sources below and retain the task-specific evidence. Official guidance: LOLER overview Official guidance: Safe use of lifting equipment (L113) Task decision: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet. Use the full topic for the decision points, practical examples, detailed control tables and source scope.

How harm develops in the linked model

People can be struck or crushed by a falling or swinging load; the hook and accessories can also strike them.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Use the full load-handling equipment and lifting operations lesson

Follow the official sources below and retain the task-specific evidence. Official guidance: LOLER overview Official guidance: Safe use of lifting equipment (L113) Task decision: Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet. Use the full topic for the decision points, practical examples, detailed control tables and source scope.

HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. Apply it: Which official source and full-topic section will you use to resolve the next decision?

Apply the learning

The operator loses radio contact while the load is hidden behind a structure.

Decision and explanation

Stop safely under the agreed method and restore a verified communication arrangement before resuming.

Loss of the agreed communication is a stop trigger; unplanned signals or assumptions cannot guide a blind load.

Lesson 11

Prepare the landing and detachment

Plan stable landing and safe detachment in advance; the receiving position is a safety-critical part of the lift.

The load is not safe merely because it reaches the destination

The receiving position must support the actual load and allow stable placement. Check the floor or structure, bearers, packing, access and space for detachment before the load is picked up. A landing area used as temporary storage can become unavailable during the lift, so ownership and protection of that area need to be clear.

Plan the sequence for controlling rotation, setting the load down, confirming stability and removing accessories. Hands and feet remain clear of crush points. The receiving team needs a method that does not require anyone to pull a sling from beneath an unstable item or reach into a trapped connection. Do not remove temporary support or bracing simply to retrieve lifting gear.

After placement, check the condition actually achieved. Is the item stable without the crane? Are its temporary fixings complete? Can accessories be detached from a safe position? An unexpected lean, damaged bearer or blocked exit holds the next step. Hand back the work area only after the load is secure, the lifting exposure has ended and the responsible people understand any remaining restrictions.

Visual practice · Prepare the landing and detachment

Lifting accessories being inspected beside a stationary UK overhead crane
SHAREhub photographic illustration · Lifting accessories being inspected beside a stationary UK overhead crane. Use the written case for the exercise; this image does not prove a defect or safe system.
The load is not safe merely because it reaches the destination

The receiving position must support the actual load and allow stable placement. Check the floor or structure, bearers, packing, access and space for detachment before the load is picked up. A landing area used as temporary storage can become unavailable during the lift, so ownership and protection of that area need to be clear.

How would a supervisor assess a warehouse pallet lift?

At a warehouse dispatch bay, a supervisor must decide whether a pallet of boxed parts can be lifted and moved by fork-lift truck. The pallet weighs 640 kg and is stable on a sound pallet; the rated truck and forks are suitable, the floor and turning route are clear, and pedestrians wait behind the barrier. If the wrapping tears or the driver loses a clear view at the crossing, stop, re-secure the load or change the route, and release only after another check.

How harm develops in the linked model

People can be struck or crushed by a falling or swinging load; the hook and accessories can also strike them.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How would a supervisor assess a warehouse pallet lift?

At a warehouse dispatch bay, a supervisor must decide whether a pallet of boxed parts can be lifted and moved by fork-lift truck.

The pallet weighs 640 kg and is stable on a sound pallet; the rated truck and forks are suitable, the floor and turning route are clear, and pedestrians wait behind the barrier. If the wrapping tears or the driver loses a clear view at the crossing, stop, re-secure the load or change the route, and release only after another check. The pre-use record and observed segregation support the decision.

StepQuestionGood answer
LoadWhat is being lifted and where is the centre of gravity?Shrink-wrapped pallet, weight confirmed, no leaning, no damaged pallet.
EquipmentIs the lift truck and attachment suitable?Correct rated capacity, fork length suitable, daily check complete.
RouteCan the load travel safely?Segregated route, no blind corner conflict, floor intact, sufficient lighting.
PeopleWho could be harmed?Pedestrians excluded, visiting driver in safe waiting area, banksman only if trained and needed.
ControlWhat stops the job?Damaged pallet, unstable load, blocked route, pedestrian incursion, equipment defect or unclear instructions.
EvidenceWhat proves control?Training record, pre-use check, route inspection, incident/near-miss learning and supervisor observation.

Apply the learning

The planned landing bearers are missing, and the receiving crew suggests putting the assembly on a small stack of loose blocks.

Decision and explanation

Keep the operation on hold and establish the planned suitable stable landing arrangement before release.

Plan stable landing and safe detachment in advance; the receiving position is a safety-critical part of the lift.

Lesson 12

Coordinate a lift across other work

Capacity and people protection are separate requirements. The complete route needs verified controls before movement.

Model practice: the next route crosses a walkway

The construction model shows a controlled lifting area, but the next proposed route crosses an occupied walkway. Existing barriers for one operation are not automatic protection for another. Trace the route as a pedestrian approaching from welfare, a contractor entering the site and a receiving worker waiting at the destination. Each viewpoint reveals a different possible entry into danger.

Coordinate the timing and layout with the site team. Avoid the occupied route by changing the sequence where practicable. Where a boundary is required, establish it before movement, maintain usable alternative access and verify that affected people understand it. A horn or a gap between breaks does not prevent an unexpected person entering.

Complete the model decisions with attention to verification. Someone must check that the boundary exists and remains effective, that the route is clear and that the movement authority is understood. After the load is safely landed, handback should deliberately reopen the route. Leaving a barrier across the normal access can provoke later bypassing, while removing it too early exposes people to unfinished lifting work.

Visual practice · Coordinate a lift across other work

Actual SHAREsimulate construction model context: A proposed lift crosses an occupied walkway
Actual SHAREsimulate model capture · A proposed lift crosses an occupied walkway. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Model practice: the next route crosses a walkway

The construction model shows a controlled lifting area, but the next proposed route crosses an occupied walkway. Existing barriers for one operation are not automatic protection for another. Trace the route as a pedestrian approaching from welfare, a contractor entering the site and a receiving worker waiting at the destination. Each viewpoint reveals a different possible entry into danger.

What good evidence looks like

Good evidence shows the lift was suitable, planned, supervised, checked and learned from. Trace a real lift from the load description and approved method through pre-use check, exclusion, operator/signaller briefing, examination status and any defect close-out. A certificate cannot prove the lift was planned for the load and route.

How harm develops in the linked model

People can be struck or crushed by a falling or swinging load; the hook and accessories can also strike them.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What good evidence looks like

Good evidence shows the lift was suitable, planned, supervised, checked and learned from.

Trace a real lift from the load description and approved method through pre-use check, exclusion, operator/signaller briefing, examination status and any defect close-out. A certificate cannot prove the lift was planned for the load and route.

EvidenceWhat it should showCommon weakness
Risk assessmentTask, load, people, route, environment and control hierarchy.Copied assessment ignores local conditions.
Lifting planLoad details, equipment, accessories, roles, exclusion zones, sequence and stop criteria.No named competent person or lift-specific information.
Equipment registerWhat equipment exists, safe working load / working load limit, location, owner and examination due date.Accessories missing from the register.
Training and authorisationOperators, slingers, signallers, lift supervisors and users are competent for the task.Attendance record used as proof of competence.
Examination and maintenanceReports are current, defects are actioned and equipment is safe to use.Reports filed but defects not closed.
Field verificationSupervisors observe real lifts and challenge drift.Assurance checks only count paperwork.

Apply the learning

The next proposed swing passes across the welfare walkway, which cannot be fully seen from the cab.

Decision and explanation

Hold the lift and establish a suitable route or sequence, effective exclusion, alternative access and agreed signalling.

Capacity and people protection are separate requirements. The complete route needs verified controls before movement.

Lesson 13

Recognise the conditions that invalidate a plan

A changed condition requires a safe hold and an operation-specific review; people must not substitute for an invalid control.

Wind, proximity and changing interfaces

The plan depends on environmental and site conditions. Wind affects a large sheet or panel differently from a compact item of the same mass. Apply the equipment instructions and competent operation-specific limits; this course cannot supply one wind speed that clears all lifts. Visibility, lightning, ground deterioration and interference from other machinery may also require a hold.

Proximity hazards include overhead electrical lines, structures, adjacent cranes and underground services affecting supports. Assess the whole machine and load envelope, not just the hook. Where electrical lines may be involved, obtain the required specialist advice and controls. A familiar driver or an estimated clearance cannot replace the safe system.

Use defined triggers that workers can recognise: changed load, unexpected movement, loss of signal, moving support, breached exclusion or environmental conditions outside the method. The supervisor keeps people safe and refers the changed assumption to the competent planner. Updating a form after the lift does not control the exposure that occurred during it.

Visual practice · Recognise the conditions that invalidate a plan

Lifting accessories being inspected beside a stationary UK overhead crane
SHAREhub photographic illustration · Lifting accessories being inspected beside a stationary UK overhead crane. Use the written case for the exercise; this image does not prove a defect or safe system.
Wind, proximity and changing interfaces

The plan depends on environmental and site conditions. Wind affects a large sheet or panel differently from a compact item of the same mass. Apply the equipment instructions and competent operation-specific limits; this course cannot supply one wind speed that clears all lifts. Visibility, lightning, ground deterioration and interference from other machinery may also require a hold.

How should controls be owned and reviewed?

Assign a competent owner, check that task controls work, involve workers and act when evidence changes. For Load-handling equipment and lifting operations, record the actual hazard and task, the chosen control, the person responsible, the evidence that it works and the point at which work must stop or be reassessed. HSE management guidance for Great Britain describes planning, worker consultation, checking and action.

How harm develops in the linked model

An unstable load, overload or uncontrolled movement can strike, crush or overturn equipment and affect people beyond the immediate lift.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should controls be owned and reviewed?

Assign a competent owner, check that task controls work, involve workers and act when evidence changes.

For Load-handling equipment and lifting operations, record the actual hazard and task, the chosen control, the person responsible, the evidence that it works and the point at which work must stop or be reassessed. HSE management guidance for Great Britain describes planning, worker consultation, checking and action. HSENI guidance for Northern Ireland describes competent help, risk control and review. These management steps do not prove that a particular task control is suitable; use the topic-specific evidence and the applicable GB or NI law elsewhere on this page.

Where ISO 45001 is adopted, connect lift planning, equipment defects, contractor coordination and verified hand-back to management arrangements. The actual load, rated configuration, competent plan and equipment condition determine the lifting decision. Certification cannot verify a sling arrangement, authorise lifting people or replace applicable examination duties. HSE: ISO 45001 management standard.

Apply the learning

Wind begins rotating a broad panel in a way not covered by the current lifting method.

Decision and explanation

Stop safely and obtain a competent review against the equipment and operation-specific limits before resuming.

A changed condition requires a safe hold and an operation-specific review; people must not substitute for an invalid control.

Lesson 14

Respond to defects and abnormal movement

Recovery requires a controlled safe state, traceable defect response and verification of the whole lifting arrangement.

Secure, report and verify the recovery

An abnormal event can indicate a failure of the equipment, support, load or method. Keep people clear and follow the planned safe-stop and emergency arrangements. Do not send someone beneath a load to discover the fault, pack a loaded support or repair an accessory in place while it remains under tension.

Identify the item and circumstances accurately. Record what changed, where it occurred and the safe state achieved, without experimenting to reproduce the event. The competent team determines repair, examination, revised planning and the evidence needed before release. Some defects create statutory reporting duties through the examination process; a local maintenance note is not a substitute for those obligations.

The release should answer both the equipment question and the operation question. A repaired component may be safe in itself while the revised load or ground arrangement remains unassessed. Communicate restrictions across shifts and contractors so a quarantined item does not return to use through a different store or team. Learning from a near miss is useful only when the relevant control changes reach the workface.

Visual practice · Respond to defects and abnormal movement

Actual SHAREsimulate construction model context: Damaged slings and an unclear examination record
Actual SHAREsimulate model capture · Damaged slings and an unclear examination record. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Secure, report and verify the recovery

An abnormal event can indicate a failure of the equipment, support, load or method. Keep people clear and follow the planned safe-stop and emergency arrangements. Do not send someone beneath a load to discover the fault, pack a loaded support or repair an accessory in place while it remains under tension.

How could BuildOut Ltd manage this in practice?

BuildOut would manage lifting through logistics planning, competent lift planning, equipment registers, exclusion zones and field verification. On a construction project, lifting risk changes daily: deliveries arrive out of sequence, ground conditions change, pedestrians move through the site, subcontractors need access and weather affects crane operations. BuildOut would not treat the lift plan as a static document; it would connect procurement, delivery bookings, lifting plans, briefings and supervisor checks.

How harm develops in the linked model

A defective or unsuitable accessory can fail and drop the load; examination does not replace pre-use checks or proper selection.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How could BuildOut Ltd manage this in practice?

BuildOut would manage lifting through logistics planning, competent lift planning, equipment registers, exclusion zones and field verification.

On a construction project, lifting risk changes daily: deliveries arrive out of sequence, ground conditions change, pedestrians move through the site, subcontractors need access and weather affects crane operations. BuildOut would not treat the lift plan as a static document; it would connect procurement, delivery bookings, lifting plans, briefings and supervisor checks.

Management elementHow the business would manage itEvidence to review
PlanLift plans are matched to the load, ground, route, crane or telehandler capacity, exclusion zone and nearby activities.Lift plan, delivery schedule and ground assessment.
ProcureMaterials are ordered in manageable packs and compatible lifting points or pallets are specified.Procurement specification and delivery note.
BriefOperators, slingers, banksmen, supervisors and affected trades are briefed before lifting starts.Briefing record and attendance.
CheckPre-use checks, accessory tags, safe working load / working load limit and exclusion zones are checked in the field.Daily check and supervisor verification.
LearnDropped loads, near misses, damaged pallets and pedestrian incursions are trended and used to change logistics.Action tracker and logistics review.

Apply the learning

A load shifts unexpectedly and a sling connection is found distorted after the assembly is safely supported.

Decision and explanation

Keep the affected equipment out of use and arrange competent investigation and verified recovery of both equipment and lifting method.

Recovery requires a controlled safe state, traceable defect response and verification of the whole lifting arrangement.

Lesson 15

Hoists, simple lifting devices and lifting people

Use equipment only for its intended lifting purpose; lifting people introduces specific requirements and cannot be improvised.

A different device does not remove the core duties

Construction lifting extends beyond cranes. Hoists, gin wheels, chain blocks and other devices can create dropped-load, crushing and fall hazards. Select equipment and anchorage for the intended use, follow installation instructions, control access and provide suitable checks and examinations. A simple manually powered device can still be lifting equipment.

Goods hoists are not passenger lifts. Prevent people riding on equipment that is not intended or authorised for them. At hoist landings, protection must prevent people falling into the hoistway or being struck by a moving platform. Keep the designed gates and safety arrangements effective; bypassing an interlock to speed material movement creates direct exposure.

Lifting people needs its own planning and equipment requirements. A convenient bucket, pallet or load sling is not a passenger carrier. Refer the proposed method to competent people rather than adapting a materials lift on site. For this awareness course, the key decision is to recognise the change of use and maintain the hold until an appropriate authorised system exists.

Visual practice · Hoists, simple lifting devices and lifting people

Lifting accessories being inspected beside a stationary UK overhead crane
SHAREhub photographic illustration · Lifting accessories being inspected beside a stationary UK overhead crane. Use the written case for the exercise; this image does not prove a defect or safe system.
A different device does not remove the core duties

Construction lifting extends beyond cranes. Hoists, gin wheels, chain blocks and other devices can create dropped-load, crushing and fall hazards. Select equipment and anchorage for the intended use, follow installation instructions, control access and provide suitable checks and examinations. A simple manually powered device can still be lifting equipment.

What training is needed?

Training must match the equipment, task, complexity and role. Competence is checked against the actual task, equipment, abnormal event and role. Briefing alone is insufficient when a person must make a stop or rescue decision.

How harm develops in the linked model

An unstable load, overload or uncontrolled movement can strike, crush or overturn equipment and affect people beyond the immediate lift.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What training is needed?

Training must match the equipment, task, complexity and role.

Competence is checked against the actual task, equipment, abnormal event and role. Briefing alone is insufficient when a person must make a stop or rescue decision.

LevelWho it is forWhat it should cover
General awarenessPeople near load routesKnow exclusion, blind-corner reporting and what to do when a pallet or sling looks defective.
Task-specific practical trainingOperators and slinger-signallersDemonstrate pre-use checks, load/rating confirmation, attachment and signals for the equipment they use.
Supervisor and line manager trainingLift supervisors and plannersCheck the plan against mass, route, ground and people; stop changed or uncertain lifts and control hand-back.
HSE, HR, OH or technical adviser coordinationEquipment managers and safety advisersMaintain registers, defects, PUWER/LOLER scope decisions, examination schedules and action close-out.
Specialist competenceCompetent lift planners and examinersPlan complex lifts or independently examine lifting equipment within their actual scope of competence.

Apply the learning

A worker proposes riding on a goods-only hoist to avoid climbing stairs.

Decision and explanation

Prevent the ride and provide a suitable authorised access arrangement; keep the goods hoist within its intended use.

Use equipment only for its intended lifting purpose; lifting people introduces specific requirements and cannot be improvised.

Lesson 16

Assess role competence through relevant evidence

Competence must be demonstrated for the assigned role, equipment and complexity; one course cannot authorise every lifting activity.

Make competence specific enough to observe

Awareness, operation, slinging, signalling, supervision, planning and examination are different capabilities. Training records can support a competence decision, but the decision needs to match the actual equipment, load, complexity and role. Familiarity with routine pallet handling does not establish the ability to plan a non-routine suspended assembly.

A safe assessment can use a supported load, drawings and staged changes. Ask the learner to identify missing mass information, a blocked landing position or a changed attachment. Observe whether they maintain the hold, explain the consequence and involve the right competent person. Practical demonstrations require a separately assessed safe setup; do not create an unsafe lift to test someone's reaction.

Record what was demonstrated and the limits: which equipment and configuration, which task and role, who assessed it and what support remains necessary. Review that authorisation after equipment changes, incidents, failed demonstrations or an expanded role. Passing this course supplies evidence of learning, while the employer remains responsible for site-specific competence and authorisation.

Visual practice · Assess role competence through relevant evidence

Actual SHAREsimulate construction model context: A long load is lifted without a suitable plan
Actual SHAREsimulate model capture · A long load is lifted without a suitable plan. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Make competence specific enough to observe

Awareness, operation, slinging, signalling, supervision, planning and examination are different capabilities. Training records can support a competence decision, but the decision needs to match the actual equipment, load, complexity and role. Familiarity with routine pallet handling does not establish the ability to plan a non-routine suspended assembly.

How should lifting competence be demonstrated for the assigned role?

Assess against the actual equipment and complexity. Ordinary awareness protects people near a route; operating, attaching, signalling, planning and examining need different capabilities. No single course title establishes every role, and an equipment operator is not automatically the competent planner or examiner.

How harm develops in the linked model

An unstable load, overload or uncontrolled movement can strike, crush or overturn equipment and affect people beyond the immediate lift.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should lifting competence be demonstrated for the assigned role?

Assess against the actual equipment and complexity. Ordinary awareness protects people near a route; operating, attaching, signalling, planning and examining need different capabilities. No single course title establishes every role, and an equipment operator is not automatically the competent planner or examiner. Related guidance: LOLER overview.

Use the changed-motor case as a safe planning exercise with the load remaining supported. The assessor introduces an unknown component or blocked landing position and observes the hold and revised planning route. Practical demonstrations must use a separately assessed safe setup; do not expose people to an unverified lift for training. Related guidance: LOLER overview.

Record the equipment/configuration, task, assessor competence, demonstrated role and limits. Reassess after a new attachment, equipment type, complex task, failed demonstration or incident. Refresher learning follows the identified gap; it cannot repair an unsafe load or unsuitable machine. Related guidance: LOLER overview.

How should lifting competence be demonstrated for the assigned role
Role and assessorObserved decisionLimits and failure responseRecord and reassessment
Nearby worker — competent supervisorRecognise the load route/exclusion and report a person or obstruction entering it.Do not walk below a load or intervene inside the trapping area.Observed boundary/reporting understanding; review changed layout or route. Related guidance: LOLER overview; Thorough examination of lifting equipment; Safe lifting by machine.
Operator — competent equipment/task assessorCheck the specific machine and rated configuration; explain limits and stop on changed load or conditions.Do not use nominal capacity as permission for any reach or attachment.Actual machine/configuration demonstration; reassess new equipment or task. Related guidance: LOLER overview; Thorough examination of lifting equipment; Safe lifting by machine.
Slinger/signaller — competent rigging/task assessorIdentify suitable accessories/points within the plan and demonstrate agreed signals.Hold an unverified point, damaged accessory or lost communication.Accessory arrangement and communication evidence; reassess changed load or rigging. Related guidance: LOLER overview; Thorough examination of lifting equipment; Safe lifting by machine.
Supervisor/planner — competent lift reviewerEstablish load, configuration, route, people and proportionate supervision; revise the unknown-motor plan.Maintain hold where mass, stability or attachment evidence is missing.Reasoned plan and verification/hand-back; review changed conditions or failed operation. Related guidance: LOLER overview; Thorough examination of lifting equipment; Safe lifting by machine.
Equipment manager — competent equipment/legal-scope adviserTrace asset to maintenance, examination, defects and competent recovery.Cannot treat maintenance, a label or overdue-report extension as examination.Asset-specific evidence and action verification; review defect trends or inventory/scope change. Related guidance: LOLER overview; Thorough examination of lifting equipment; Safe lifting by machine.
Examiner — suitably competent independent reviewerIdentify scope, safety-critical parts, defect significance and reporting/release implications.Stay within equipment expertise and impartial examination arrangements.Compliant report, scheme where used and defect communication; review new equipment/scope or uncertain findings. Related guidance: LOLER overview; Thorough examination of lifting equipment; Safe lifting by machine.

Guidance for these decisions: LOLER overview; Thorough examination of lifting equipment; Safe lifting by machine. Apply the legal route for the work location; illustrative scenarios are SHARE teaching examples.

Apply the learning

A candidate presents a general lifting-awareness certificate as authority to supervise a complex assembly lift.

Decision and explanation

Check the competence evidence against the specific supervisory role and lift, and provide the required assessment and support.

Competence must be demonstrated for the assigned role, equipment and complexity; one course cannot authorise every lifting activity.

Lesson 17

Capstone: review the changed steel assembly

A defensible restart joins competent revision, physical verification and shared understanding across every affected lifting control.

Bring load, support, people and records together

At fictional Foundry Court, the original method covers a short steel unit lifted from a verified setup to prepared bearers. The delivered unit now includes a longer bracket, the crane is proposed closer to a trench and a delivery blocks the receiving route. These are connected changes: a longer load may change mass, centre of gravity and swing, while the new position may alter radius and support loading.

Build a release recommendation from evidence rather than the number of signatures. Identify what is known, what has changed, who has the competence to resolve it and what physical verification is required. Keep an unresolved item visible as a hold. Do not average a strong equipment report against a weak ground assessment; each safety-critical assumption must be acceptable.

After the technical revision, check implementation. Has the crane stood where assessed? Are the selected accessories present and identified? Is the receiving area prepared and the pedestrian route controlled? Can the operator and signaller describe the same stop method? A technically sound document that describes yesterday's setup cannot release today's operation.

Visual practice · Capstone: review the changed steel assembly

Lifting accessories being inspected beside a stationary UK overhead crane
SHAREhub photographic illustration · Lifting accessories being inspected beside a stationary UK overhead crane. Use the written case for the exercise; this image does not prove a defect or safe system.
Bring load, support, people and records together

At fictional Foundry Court, the original method covers a short steel unit lifted from a verified setup to prepared bearers. The delivered unit now includes a longer bracket, the crane is proposed closer to a trench and a delivery blocks the receiving route. These are connected changes: a longer load may change mass, centre of gravity and swing, while the new position may alter radius and support loading.

What does load-handling equipment and lifting operations mean?

It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system. Avoid / redesign: Avoid moving the motor by redesigning work at its current position where feasible. Control the task: Use rated lifting gear, secure attachments and a segregated travel route.

How harm develops in the linked model

An unstable load, overload or uncontrolled movement can strike, crush or overturn equipment and affect people beyond the immediate lift.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What does load-handling equipment and lifting operations mean?

It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system. Avoid / redesign: Avoid moving the motor by redesigning work at its current position where feasible. Control the task: Use rated lifting gear, secure attachments and a segregated travel route.

Verify before release: Planner records feasibility; unclear task holds lift. It means moving loads using suitable aids or lifting equipment under a planned, supervised and competent system. Choose a safer way to move the load before designing a lift.

Apply it: Which part of this plan would you check at the workface before authorising the task?

Apply the learning

The revised assembly, crane position and landing route no longer match the signed plan.

Decision and explanation

Maintain the hold, resolve all affected assumptions through competent planning, verify the actual setup and brief the team before release.

A defensible restart joins competent revision, physical verification and shared understanding across every affected lifting control.

Lesson 18

Turn learning into a workface routine

Apply the learning through task-specific evidence, clear ownership and follow-up; course completion is not a release for live lifting.

Ask for the evidence that changes the decision

Choose one lifting activity from your work and describe its complete journey without collecting private or identifying information for this exercise. Write down the load, the people exposed, the equipment, the support and the receiving position. Then identify one assumption that you would need a competent person to verify before you could recommend release.

Translate that assumption into a practical question. Instead of asking whether paperwork is complete, ask how the actual load mass was established, how this outrigger position was assessed, or how the receiving crew remains outside the trapping area. The answer should point to relevant evidence and a control at the workface. If it does not, keep the issue open through the responsible site process.

Use a toolbox briefing to connect the method to what people will do: where to stand, whose movement instructions apply, how to raise a stop and what invalidates the plan. Follow up after the operation to check whether the route, equipment or sequence changed. Record the improvement through your organisation's authorised arrangements; the fictional course record is not an operating lift plan.

Visual practice · Turn learning into a workface routine

Actual SHAREsimulate construction model context: A long load is lifted without a suitable plan
Actual SHAREsimulate model capture · A long load is lifted without a suitable plan. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Ask for the evidence that changes the decision

Choose one lifting activity from your work and describe its complete journey without collecting private or identifying information for this exercise. Write down the load, the people exposed, the equipment, the support and the receiving position. Then identify one assumption that you would need a competent person to verify before you could recommend release.

Who should use this load-handling and lifting page?

This page supports learners, supervisors, managers and advisers who need to understand how lifting risk is planned, controlled and evidenced. To understand course section 6.3 and construction-linked load-handling principles with practical examples. To check whether lifting plans, equipment, exclusion zones, operators and attachments match the job.

How harm develops in the linked model

An unstable load, overload or uncontrolled movement can strike, crush or overturn equipment and affect people beyond the immediate lift.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Who should use this load-handling and lifting page?

This page supports learners, supervisors, managers and advisers who need to understand how lifting risk is planned, controlled and evidenced.

Safety-qualification learners

To understand course section 6.3 and construction-linked load-handling principles with practical examples.

Supervisors

To check whether lifting plans, equipment, exclusion zones, operators and attachments match the job.

Managers and dutyholders

To resource competent people, examination regimes, maintenance and contractor coordination.

Health and safety advisers and auditors

To test whether lifting-equipment, work-equipment, manual handling and workplace transport controls work in the field.

How can this guidance help in practice?

Workers and people carrying out the task
Use the Load-Handling Equipment and Lifting Operations guidance to recognise relevant hazards, understand the precautions and identify when to stop, report a problem or ask for competent support.
Supervisors and managers
Use the task examples and control checks to plan work, brief the team, check implementation and assign improvements with owners and follow-up.
Safety, health, risk and assurance professionals
Use the explanations, sources and operational examples to develop assessments, audits and control verification. Check the actual scope and jurisdiction before applying a duty.
Learners, trainers and organisational decision makers
Use the definitions and examples to connect theory with workplace decisions, build briefings and ask informed questions. This page does not certify competence or authorise work.

Apply the learning

Your action plan says only “improve lifting safety” and assigns no task, evidence or owner.

Decision and explanation

Choose a specific lifting assumption, an accountable owner, a verification step and a follow-up point.

Apply the learning through task-specific evidence, clear ownership and follow-up; course completion is not a release for live lifting.