Silica dust in construction · learning reader

Free training · Approx. 2h 10m–3h 10m · estimated self-paced learning, including activities and assessment.

Public teaching is free without an account. A free learner account is required for confirmed LMS assessment, completion and certificate records. See the full course outline and access routes.

Teaching and applied cases for accessible study. The interactive course records assessed completion.

Lesson 1

Find the dust-generating task

Concrete, mortar, stone and other silica-containing materials can generate respirable dust during processing. Product and task information matter.

Which materials and tasks create silica dust?

Silica risk depends on both the material and the energy of the work activity.

Relevant direct sources: HSE.

Some materials contain more silica than others, but a lower-silica material can still create harmful exposure if the task is dusty, prolonged or enclosed. The assessor should never rely on material name alone.

The practical rule is to treat powered cutting, grinding, drilling, scabbling, polishing, blasting, breaking and dry sweeping as exposure-generating tasks until suitable control is proven.

Material or workTypical taskRisk point
Sandstone, gritstone and quartziteCutting, carving or grinding.Often high silica content and high RCS potential. HSE
Concrete and mortarCutting, chasing, coring or breaking.Common construction source of RCS. HSE
Brick and blockSaw cutting, drilling and chasing.Repeated short cuts can create cumulative exposure. HSE
Granite and engineered stonePolishing, cutting and edge finishing.Workshop exposure can be intense and repeated. HSE
Foundry sand or mouldsShakeout, fettling and cleaning.Mixed metal and silica dust exposure. HSE
Settled construction dustDry sweeping or compressed air cleaning.Re-suspends fine dust into the breathing zone. HSE

Visual practice · Find the dust-generating task

Dust-extracted masonry saw and vacuum at a UK site
SHAREhub photographic illustration · Dust-extracted masonry saw and vacuum at a UK site. Use the written case for the exercise; this image does not prove a defect or safe system.
Which materials and tasks create silica dust?

Silica risk depends on both the material and the energy of the work activity. Relevant direct sources: HSE. Some materials contain more silica than others, but a lower-silica material can still create harmful exposure if the task is dusty, prolonged or enclosed. The assessor should never rely on material name alone.

How should silica dust risk be assessed?

How should silica dust risk be assessed? Assess the material, task energy, duration, enclosure, people exposed, controls and evidence before work starts.Relevant direct sources: HSE. A silica assessment should be task-specific enough to change the work. 'Cutting concrete' is not enough.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should silica dust risk be assessed?

Assess the material, task energy, duration, enclosure, people exposed, controls and evidence before work starts.

Relevant direct sources: HSE.

A silica assessment should be task-specific enough to change the work. 'Cutting concrete' is not enough. The assessor needs to know how much cutting, which tool, whether it is indoors or outside, whether water or extraction is fitted, whether the extraction unit is suitable, who stands nearby, how dust is cleaned up and whether any tight-fitting RPE has been face-fit tested for that wearer, while all selected RPE meets the task’s protection, compatibility and use requirements.

The strongest assessments look at both planned and foreseeable poor conditions. What if water cannot be used because of electrics? What if the vacuum filter blocks? What if a subcontractor brings a dry-cutting tool? What if the task moves indoors? What if a worker has stubble that breaks the mask seal? These practical questions turn silica assessment into risk control.

Assessment factorWhat to askWhy it matters
MaterialDoes the material contain silica and how much is likely?Sandstone, concrete, brick, mortar, granite and engineered stone create different exposures. HSE
TaskIs work cutting, drilling, grinding, polishing, blasting, breaking or sweeping?High-energy tasks generate respirable dust quickly. HSE
MethodCan cutting be avoided, reduced, wet-controlled or extracted?Design and method changes are stronger than PPE. HSE
EnvironmentIs work indoors, enclosed, windy, overhead or near other trades?Dust build-up and spread can change exposure dramatically. HSE
Duration/frequencyHow long and how often will the task occur?Dose accumulates even where each task looks short. HSE
People exposedWho is doing the task and who is nearby?Bystanders, labourers and cleaners can be exposed. HSE
Control evidenceWhat proves water, extraction, RPE and cleaning will work?Controls must be verified before and during work. HSE

Apply the learning

The team says there is no silica risk because it is cutting a manufactured paving product.

Decision and explanation

Check the material and dust-generating task and assess respirable crystalline silica exposure.

Concrete, mortar, stone and other silica-containing materials can generate respirable dust during processing. Product and task information matter.

Lesson 2

How respirable dust causes harm

Fine particles can reach deep into the lungs. Lack of immediate discomfort is not evidence that repeated exposure is controlled.

How do the lungs work, and how can workplace exposures affect breathing?

Interactive anatomy · Respiratory tract and lungs · Updated 2026-10-19

An adult chest cutaway showing the trachea dividing into branching airways within two lungs, ribs at the sides and the domed diaphragm below.View full detail ↗
Lungs and airways in the chest

Locate the lungs, branching airways and diaphragm below them. The cutaway reveals structures normally hidden by the chest wall.

Trace the source-to-breathing-zone route in this lesson. Which change would prevent the contaminant reaching the person?

educational illustration · healthy anatomy; enlarged details and teaching colours.

How do the lungs work, and how can workplace exposures affect breathing?

Explains respirable crystalline silica reaching deep tissue and the scarring mechanism; does not predict latency, dose or individual disease.

Visual practice · How respirable dust causes harm

Actual SHAREsimulate construction model context: Dry cutting is proposed without its source control
Actual SHAREsimulate model capture · Dry cutting is proposed without its source control. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Investigate 1: Workstation

The workstation is visible. The written case supplies the proposed dry cutting and unavailable dust-suppression control; neither dust concentration nor effective control can be established from this distant view.

Investigate 2: Site boundary

The boundary separates the modelled site from the road. Include people beyond the immediate cutting task when considering exposure and the case’s proposed work near the public boundary.

Investigate 3: Material storage

Stored materials provide task context. Confirm the material and cutting method from reliable information, then verify the task’s source control. Appearance alone cannot establish a material’s silica content.

How do the lungs work, and how can workplace exposures affect breathing?

Interactive anatomy · Respiratory tract and lungs · Updated 2026-10-17 Explains respirable crystalline silica reaching deep tissue and the scarring mechanism; does not predict latency, dose or individual disease. COPD and coal-dust topics may reuse normal anatomy only until separate mechanisms are reviewed. · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved Dust-related fibrosis · silica Fine respirable crystalline silica can reach deep into the lungs, causing inflammation and areas of scarring. Established silicosis damage cannot be reversed and may progress after exposure ends.

What do people commonly get wrong about silica dust?

Common misunderstandings usually underestimate invisible dust, short tasks, clean-up exposure and RPE limitations. Relevant direct sources: HSE. Silica dust is dangerous partly because it does not look dramatic. A small haze, dusty clothing or powder on a sill can be treated as mess rather than evidence of airborne exposure.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Severe breathing difficulty: call 999

Call 999 for severe breathing difficulty, such as gasping, choking or being unable to get words out. Do not wait for this activity to finish. Do not enter a contaminated or oxygen-deficient space to attempt an unprotected rescue. NHS: Shortness of breath · HSE: Asphyxiation hazards in welding and allied processes

Respiratory tract and lungsExplore structure, function and workplace decisions

Follow air from the upper airway to the air sacs. Separate moving air from exchanging gases, then compare irritation, narrowed airways and two distinct scarring examples.

Front teaching cutaway with patient right/left marked. Right lung: three lobes; left: two. Surrounding tissue is omitted to reveal the pathway.

The complete 2D lesson is ready. Choose Load 3D to rotate the original teaching model.

Structure 1 of 10

Nose and mouth

Air enters and leaves here.

These openings lead into the airway. The arrows show air, which is a mixture of gases, rather than a stream of pure oxygen.

Frimley Health NHS Foundation Trust: How your lungs work · Central and North West London NHS Foundation Trust: How do we breathe?
Choose a part by name · 10 structures

Follow the process

Choose a still step or play the sequence. Illustrative timing; no measurement or personal assessment.

1 · Make space

The diaphragm moves down and the chest expands. This makes room for air to enter.

Practise a workplace decision

Learning activity only. These choices do not diagnose a condition or certify practical competence.

Read all anatomy and process explanations without the viewer

Simplified education, not diagnosis, a lung-function or oxygen-saturation test, an exposure calculator or a fitness-to-work assessment. No breath-holding challenge, breathing-rate score or personal health-data collection. Ordinary particle filters do not protect against every gas or oxygen deficiency. COPD and coal-dust topics may reuse normal anatomy only until separate mechanisms are reviewed.

Nose and mouth

Air enters and leaves here. These openings lead into the airway. The arrows show air, which is a mixture of gases, rather than a stream of pure oxygen. Frimley Health NHS Foundation Trust: How your lungs work · Central and North West London NHS Foundation Trust: How do we breathe?

Trachea

The windpipe carries air into the chest. It leads towards the two main branches supplying the lungs. Frimley Health NHS Foundation Trust: How your lungs work

Bronchi

A main branch carries air into each lung. The right and left bronchi divide repeatedly inside the lungs. Follow one branch to see where it leads. Frimley Health NHS Foundation Trust: How your lungs work · University Hospitals of North Midlands NHS Trust: My lung surgery: about your lungs

Bronchioles

Smaller branches distribute air. These airways lead towards the air sacs. They are not blood vessels. Frimley Health NHS Foundation Trust: How your lungs work

Alveoli

Tiny air sacs provide a gas-exchange surface. At the end of the airway route, oxygen and carbon dioxide move between the air sacs and neighbouring blood vessels. The enlarged view is not to scale. Frimley Health NHS Foundation Trust: How your lungs work · Central and North West London NHS Foundation Trust: How do we breathe?

Air–blood barrier

A thin boundary separates air from blood. The air-sac and capillary walls form the exchange boundary. Gases cross it; the illustration keeps blood cells inside the vessel and air inside the sac. Central and North West London NHS Foundation Trust: How do we breathe?

Pulmonary capillaries

Small blood vessels pass beside the air sacs. Blood takes up oxygen from alveolar air and releases carbon dioxide towards it. Circulation continues while breathing continues. Central and North West London NHS Foundation Trust: How do we breathe?

Diaphragm

This muscle helps make room for a breath. During inhalation it contracts and flattens downwards. During a quiet exhalation it relaxes towards its dome shape. Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved

Rib cage and breathing muscles

Chest movement changes the space around the lungs. Muscles around the ribs help the chest expand. The lungs follow the changing space; they do not inflate by contracting as muscles. Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved

Pleura

Two thin layers surround the lungs and line the chest. A small amount of fluid between the layers helps the surfaces slide during breathing. This lining sits outside the lung tissue; it is not an alveolar wall. Blackpool Teaching Hospitals NHS Foundation Trust: Pleural clinic

The process, step by step

1 · Make space The diaphragm moves down and the chest expands. This makes room for air to enter. Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved

2 · Move air Follow air from the nose or mouth, through the trachea and into the main bronchi. Frimley Health NHS Foundation Trust: How your lungs work

3 · Reach the air sacs Follow one smaller airway to its alveoli. Other branches are dimmed only to make the route easier to follow. Frimley Health NHS Foundation Trust: How your lungs work

4 · Change scale The highlighted air sac links to a magnified air–blood interface. This is a change of scale, not a new organ. Central and North West London NHS Foundation Trust: How do we breathe?

5 · Exchange gases O₂ moves towards the blood; CO₂ moves towards alveolar air. Blood stays in its vessel and circulation does not pause for this step. Central and North West London NHS Foundation Trust: How do we breathe?

6 · Breathe out The breathing muscles relax and air moves out. Oxygen-carrying blood continues towards the heart and the wider circulation. Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved

Mechanisms and their limits

Dust-related fibrosis · silica Fine respirable crystalline silica can reach deep into the lungs, causing inflammation and areas of scarring. Scarred tissue does not work normally. Established silicosis damage cannot be reversed and may progress after exposure ends. Disease often develops over years, but very heavy exposure can cause much faster disease. No animation time represents a number of shifts or a safe dose. Show selected scarred regions, not every air sac filling with sand. This example does not diagnose the cause of breathlessness or show every effect of silica. NHS: Silicosis

Plan and control silica-generating cutting

Understand silicosis and seek assessment

Repeated uncontrolled cutting of paving materials

A paving crew uses a cut-off saw on kerbs without effective dust suppression. Explicit time jump: silicosis usually develops after prolonged exposure, sometimes faster after very heavy exposure. Scarring does not appear during the 32-second clip. The dust route and later fibrosis are explanatory stages. No single cut, visible cloud or symptom predicts an individual’s disease.

A silica-generating activity Cutting paving blocks or kerbs can create very fine silica-containing dust near the operator and nearby workers. Plan cuts and material choices before work starts. HSE: Construction dust: cutting paving blocks, kerbs and flags · NHS: Silicosis

Fine dust reaches deeper lung regions Some inhaled fine particles reach the alveolar region. Repeated uncontrolled exposure across separate tasks and days is represented by a clearly labelled time jump. NHS: Silicosis

Later inflammation and fibrosis The chosen long-term example marks inflammation and scarred lung tissue that cannot function normally. This is not a real-time scan, exposure calculator or inevitable outcome after one task. NHS: Silicosis

Control dust at the task Reduce cutting where possible, use suitable water suppression or on-tool extraction with the required RPE, and check controls. Report symptoms and exposure history to a healthcare professional; controls do not erase existing scarring. HSE: Construction dust: cutting paving blocks, kerbs and flags · NHS: Silicosis

Read the practice situations and all answer explanations
LU-Q1: Which plan best addresses the hazard?

A team plans repeated concrete cuts with a handheld cut-off saw. Dust can enter the operator’s and nearby workers’ breathing zones.

Open a window and use the same dry-cutting method. — A window alone does not control dust generated beside the face. Choose task controls that prevent or capture it at source.

First reduce the need to cut, then assess source suppression or extraction and any required suitable RPE. — This addresses the task before exposure occurs. Check that suppression or extraction works and that required RPE is suitable, fitted and used.

Continue while nobody is coughing. — Symptoms are not an exposure monitor. Harmful respirable dust may be invisible, and a worker can feel well during exposure.

HSE: Construction dust: cutting paving blocks, kerbs and flags
LU-Q2: What is the most useful next action?

A bakery worker notices repeated wheeze after dusty flour tasks, including some symptoms later in the evening.

Report the pattern and seek medical and workplace assessment. — Reporting the pattern allows exposure controls and clinical assessment to be reviewed. Symptoms can be delayed; a clinician may need further investigation.

Use this model to diagnose occupational asthma. — The model explains a mechanism. It cannot diagnose asthma or establish that work caused it.

Assume the task is safe if breathing improves away from work. — Improvement away from work may be useful information for investigation, but it does not show that returning to the same exposure is safe.

HSE: Asthma: an overview · HSE: Advice for employers: occupational asthma · NHS: Asthma · HSE: Flour dust and risks to bakers
LU-Q3: What is the important distinction?

One diagram shows a narrowed airway at LUN03–04. A second shows scarred gas-exchange tissue around LUN05–07.

They show the same disease at successive stages. — Narrowed airways and scarred lung tissue are different changes. One is not automatically the next stage of the other.

Both effects disappear when airborne dust settles. — Removing airborne dust does not reverse established fibrosis. Controlling further exposure remains important.

Airway narrowing and tissue fibrosis are different mechanisms. — Correct. Airway narrowing affects the passage for air; fibrosis affects lung tissue and its function. Neither picture supplies an individual diagnosis.

NHS: Silicosis · NHS: Asthma
Sources and original assets

Original simplified teaching geometry and diagrams; no source illustration or third-party anatomy model copied. Source references support the learner copy and do not grant artwork rights.

· Three.js MIT licence

All anatomy, process and practice explanations remain available in the expandable reading sections. Interactive selection requires JavaScript.

Respiratory tract and lungs · SHAREhub environment

Severe breathing difficulty: call 999

Call 999 for severe breathing difficulty, such as gasping, choking or being unable to get words out. Do not wait for this activity to finish. Do not enter a contaminated or oxygen-deficient space to attempt an unprotected rescue. NHS: Shortness of breath · HSE: Asphyxiation hazards in welding and allied processes

What do people commonly get wrong about silica dust?

Common misunderstandings usually underestimate invisible dust, short tasks, clean-up exposure and RPE limitations.

Relevant direct sources: HSE.

Silica dust is dangerous partly because it does not look dramatic. A small haze, dusty clothing or powder on a sill can be treated as mess rather than evidence of airborne exposure. Workers may also believe outdoor work is automatically safe, or that a mask alone is enough.

The best training uses specific mistakes. It shows why dry sweeping is stopped, why vacuum class matters, why stubble can defeat a tight-fitting mask and why other trades must be protected.

MisunderstandingRealityTeaching point
Only visible clouds matter.RCS may be too fine to see under normal light.Control the task, not just visible dust. HSE
A short cut is low risk.Repeated short cuts create cumulative dose.Plan all high-energy silica tasks. HSE
Outdoor work is safe.Wind direction and breathing-zone exposure still matter.Use controls outdoors too. HSE
Any vacuum will do.Fine dust can pass through unsuitable equipment.Use suitable dust-class extraction and maintain it. HSE
FFP3 solves the problem.RPE depends on fit, wear time, compatibility and user behaviour.Use RPE as part of a control package. HSE HSE construction dust and RPE selection
Cleaning happens after exposure ends.Dry sweeping can be a high-exposure task.Control clean-up as part of the job. HSE

Apply the learning

A worker feels well after months of dry cutting and concludes the method is safe.

Decision and explanation

Explain that serious lung harm can develop without immediate symptoms and control exposure now.

Fine particles can reach deep into the lungs. Lack of immediate discomfort is not evidence that repeated exposure is controlled.

Lesson 3

Assess people, task and environment

Enclosure and nearby people change exposure. Assessment must address source generation and spread through the whole working arrangement.

How should a concrete cutting task be controlled?

A worked task example shows how silica dust control should be planned, checked and evidenced at the workface.

Visual practice · Assess people, task and environment

Dust-extracted masonry saw and vacuum at a UK site
SHAREhub photographic illustration · Dust-extracted masonry saw and vacuum at a UK site. Use the written case for the exercise; this image does not prove a defect or safe system.
How should a concrete cutting task be controlled?

How should a concrete cutting task be controlled? A worked task example shows how silica dust control should be planned, checked and evidenced at the workface.Control RCS exposure while cutting a concrete service chaseTask material and setting: A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room.People and prerequisites: The site manager owns the work; the cutter checks material, other occupants, tool and extraction compatibility; a competent adviser plans exposure verification where needed.Before: Consider a surface route or off-site prefabrication.

How does silica dust control differ by sector?

The same health risk appears in different forms across construction, stonework, foundry, quarry, utilities and maintenance work. Relevant direct sources: HSE. The control principle is common, but the operational detail changes. A stone workshop needs fixed extraction, segregation and cleaning regimes.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Control RCS exposure while cutting a concrete service chase

Task material and setting: A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room.

People and prerequisites: The site manager owns the work; the cutter checks material, other occupants, tool and extraction compatibility; a competent adviser plans exposure verification where needed.

Before: Consider a surface route or off-site prefabrication. If cutting remains necessary, fit effective on-tool extraction with an appropriate M/H-class unit or suitable water suppression, segregate the area and select residual RPE.

During: Check extraction flow and capture, position the tool, keep others out, clean with a suitable vacuum or wet method and prevent dust migration.

Hold or stop: Stop for failed extraction, dry sweeping, visible escape, unknown material, unprotected bystanders or RPE not fit for the wearer.

Completion and hand back: Clean and inspect the area, close defects, review monitoring and release access only after dust control is verified.

Evidence: Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back.

A refurbishment contractor needs to cut a series of concrete channels in a leisure-centre plant room. The job is indoors, noisy, near existing services and close to other trades. A generic RAMS says 'wear dust mask and use water where possible', but the work area has poor drainage and a standard vacuum is not suitable for fine construction dust.

A competent silica plan would first challenge whether chasing is needed at all. Could the route be surface-mounted, pre-formed or moved? If cutting remains necessary, the plan should specify tool, on-tool extraction or wet suppression, compatible electrical controls, segregation, suitable RPE, face fit where tight-fitting, clean-up method, waste route, supervision and a stop rule if visible dust escapes.

Decision pointWeak planStronger silica-control plan
DesignCut channels as shown.Check whether routing, pre-formed containment or alternative fixing avoids cutting. HSE
Tool selectionUse available grinder.Use a tool with effective on-tool extraction or wet system matched to the task. HSE
Dust extractionUse a workshop vacuum.Use suitable dust-class extraction, inspected and maintained for fine dust. HSE
RPEWear dust mask.Select suitable RPE for the assessed task; for high-dust silica construction, FFP3 is an example, with face fit and wearer checks. HSE HSE construction dust and RPE selection
SegregationTell other trades to keep clear.Set exclusion zone, sequence work and prevent bystander exposure. HSE
HousekeepingSweep up afterwards.Use suitable vacuum or damp cleaning; never dry sweep silica dust. HSE
EvidenceRAMS signed.Task-specific assessment, equipment checks, RPE fit, briefing and supervisor verification. HSE

How does silica dust control differ by sector?

The same health risk appears in different forms across construction, stonework, foundry, quarry, utilities and maintenance work.

Relevant direct sources: HSE.

The control principle is common, but the operational detail changes. A stone workshop needs fixed extraction, segregation and cleaning regimes. A construction site needs sequencing, controlled tools and supervisor checks. A utility team needs mobile controls that work at the excavation or roadside.

This is why a single generic dust assessment is weak. The control standard must fit the sector, task, environment and people exposed.

SectorTypical silica activityControl focus
Construction refurbishmentChasing walls, cutting block, drilling concrete.Avoid cutting, on-tool extraction/water, task-selected RPE (for example FFP3 for high-dust silica work), segregation and clean-up. HSE HSE construction dust and RPE selection
StonemasonryCutting and polishing stone or engineered stone.Wet methods, extraction, enclosure, RPE and health surveillance. HSE
UtilitiesRoad saws, duct cutting and excavation dust.Water suppression, traffic interface, public protection and mobile welfare. HSE
FoundrySand mould handling, shakeout and fettling.Enclosure, LEV, RPE and mixed-dust monitoring. HSE
QuarryingDrilling, crushing and processing stone.Cab filtration, suppression, maintenance and exposure monitoring. HSE
Facilities maintenanceSmall drilling and fixing jobs in older premises.Pre-planning, controlled drilling and vacuum attachment. HSE

A refurbishment team needs portable tool controls, exclusion and a checked hand-back; a production workshop instead needs repeatable source capture, planned cleaning and maintenance across many tasks. In both illustrations the manager tests control effectiveness during real work and reviews exposure evidence after material, tool or layout changes. The same mask or vacuum cannot be selected solely from the word silica. HSE silica task-control context.

Apply the learning

Cutting moves into an enclosed room next to other trades.

Decision and explanation

Review the changed task, ventilation, duration, material and everyone who may be exposed.

Enclosure and nearby people change exposure. Assessment must address source generation and spread through the whole working arrangement.

Lesson 4

Avoid and reduce at design stage

Work design and procurement can reduce dust at source. Residual exposure still needs an effective task-specific control system.

What is silica dust and why is it so harmful?

Respirable crystalline silica (RCS) is the fine airborne fraction released when silica-containing stone, concrete or similar material is worked. Avoid / redesign: Assess a surface service route that avoids cutting. Control the task: Match suppression or extraction to the tool and separate bystanders. Verify before release: Read the full task example, checks and stop points on this page.

It can enter the deep lung and cause irreversible silicosis, COPD and lung cancer; dust may be invisible under normal lighting. Silica dust is airborne dust containing respirable crystalline silica, usually produced when materials such as concrete, mortar, brick, stone, tiles, ceramics, engineered stone, rock or sandstone are cut, drilled, ground, polished, blasted or broken. Apply it: Which part of this plan would you check at the workface before authorising the task?

Visual practice · Avoid and reduce at design stage

Actual SHAREsimulate construction model context: Dry cutting is proposed without its source control
Actual SHAREsimulate model capture · Dry cutting is proposed without its source control. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
What is silica dust and why is it so harmful?

Respirable crystalline silica (RCS) is the fine airborne fraction released when silica-containing stone, concrete or similar material is worked. Avoid / redesign: Assess a surface service route that avoids cutting. Control the task: Match suppression or extraction to the tool and separate bystanders. Verify before release: Read the full task example, checks and stop points on this page.

How can the ISO 45001 hierarchy of controls reduce respirable crystalline silica exposure at source?

How can the hierarchy of controls reduce respirable crystalline silica exposure at source?Remove or reduce the hazard before relying on procedures or personal protection.For silica dust, assess the actual task and first look for a way to remove the hazard. Where that is not possible, consider a safer substitute, engineered separation and then clear work procedures. PPE protects against remaining exposure; it does not make an uncontrolled task safe. In Northern Ireland, verify the separate legal route and site instructions.For the service chase, first test a surface route that avoids cutting.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How can the ISO 45001 hierarchy of controls reduce respirable crystalline silica exposure at source?

Remove or reduce the hazard before relying on procedures or personal protection.

For silica dust, assess the actual task and first look for a way to remove the hazard. Where that is not possible, consider a safer substitute, engineered separation and then clear work procedures. PPE protects against remaining exposure; it does not make an uncontrolled task safe. HSE hierarchy of controls

The selected measures need a named owner, a usable stop point and a check that they still work when the task or conditions change. In Northern Ireland, verify the separate legal route and site instructions.

For the service chase, first test a surface route that avoids cutting. If a substitute material or method is proposed, check all hazards rather than assuming lower silica means safe dust. Where cutting remains necessary, match suppression or extraction to the tool, prevent bystander exposure, control clean-up and select suitable residual RPE. The site manager provides the method and equipment; the supervisor verifies water or airflow and stops when the planned control fails. ERICPD (Eliminate, Reduce, Isolate, Control, PPE, Discipline) is a teaching prompt here; Discipline means keeping controls effective through checking and learning. HSE topic-specific control sequence.

How can the ERICPD hierarchy of controls reduce respirable crystalline silica exposure at source?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Control RCS exposure while cutting a concrete service chase
Activity and exposure
A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room.
Before work
Consider a surface route or off-site prefabrication. If cutting remains necessary, fit effective on-tool extraction with an appropriate M/H-class unit or suitable water suppression, segregate the area and select residual RPE.
During the activity
Check extraction flow and capture, position the tool, keep others out, clean with a suitable vacuum or wet method and prevent dust migration.
Hold or stop
Stop for failed extraction, dry sweeping, visible escape, unknown material, unprotected bystanders or RPE not fit for the wearer.
Hand-back and release
Clean and inspect the area, close defects, review monitoring and release access only after dust control is verified.
Evidence to retain
Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back.
Decision owner
Site manager with competent cutter and occupational hygienist
Full example
Read the activity, checks and hand-back in context
ERICPD control levelTopic-specific exampleSource and full task context
Eliminate

Assess a surface service route that avoids cutting.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Reduce

Check all hazards of a proposed substitute material or method.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Isolate

Match suppression or extraction to the tool and separate bystanders.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Control

Control clean-up and provide the assessed equipment and method.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
PPE

Select suitable residual RPE.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Discipline

Verify water or airflow and stop when the planned control fails.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence

How can the ISO 45001 hierarchy of controls reduce respirable crystalline silica exposure at source?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Control RCS exposure while cutting a concrete service chase
Activity and exposure
A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room.
Before work
Consider a surface route or off-site prefabrication. If cutting remains necessary, fit effective on-tool extraction with an appropriate M/H-class unit or suitable water suppression, segregate the area and select residual RPE.
During the activity
Check extraction flow and capture, position the tool, keep others out, clean with a suitable vacuum or wet method and prevent dust migration.
Hold or stop
Stop for failed extraction, dry sweeping, visible escape, unknown material, unprotected bystanders or RPE not fit for the wearer.
Hand-back and release
Clean and inspect the area, close defects, review monitoring and release access only after dust control is verified.
Evidence to retain
Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back.
Decision owner
Site manager with competent cutter and occupational hygienist
Full example
Read the activity, checks and hand-back in context
Five-level control stage(s)Topic-specific exampleSource and full task context
Elimination

Assess a surface service route that avoids cutting.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Substitution

Check all hazards of a proposed substitute material or method.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Engineering controls

Match suppression or extraction to the tool and separate bystanders.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Administrative controls

Control clean-up and provide the assessed equipment and method.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
PPE

Select suitable residual RPE.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Administrative controls

Verify water or airflow and stop when the planned control fails.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence

Apply the learning

A design choice could replace repeated site cutting with accurately pre-sized components.

Decision and explanation

Consider eliminating or reducing on-site cutting before selecting downstream controls.

Work design and procurement can reduce dust at source. Residual exposure still needs an effective task-specific control system.

Lesson 5

Water suppression that works at the cut

The control must work at the dust-generation point throughout the task; wet ground is not evidence of effective suppression.

Turn silica dust knowledge into a decision

Use the evidence to improve the actual work arrangement. Change at source: Assess a surface service route that avoids cutting. Make it observable: Read the full task example, checks and stop points on this page. Keep useful evidence: Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back.

Silica dust is airborne dust containing respirable crystalline silica, usually produced when materials such as concrete, mortar, brick, stone, tiles, ceramics, engineered stone, rock or sandstone are cut, drilled, ground, polished, blasted or broken. The dangerous fraction is often invisible under normal lighting and can reach the deep lung. Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back. Apply it: What evidence would show that the change improves this task, rather than only completing a record?

Visual practice · Water suppression that works at the cut

Dust-extracted masonry saw and vacuum at a UK site
SHAREhub photographic illustration · Dust-extracted masonry saw and vacuum at a UK site. Use the written case for the exercise; this image does not prove a defect or safe system.
Turn silica dust knowledge into a decision

Use the evidence to improve the actual work arrangement. Change at source: Assess a surface service route that avoids cutting. Make it observable: Read the full task example, checks and stop points on this page. Keep useful evidence: Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back.

What does a controlled silica workflow look like?

What does a controlled silica workflow look like? A controlled workflow prevents dust generation where possible, captures remaining dust and prevents secondary exposure during clean-up.Relevant direct sources: HSE, HSE. Silica control is often lost in the sequence, not the theory. Work is planned too late, the right tool is unavailable, the vacuum does not fit the shroud, the water supply is awkward, the exclusion zone is not set and cleaning is rushed.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What does a controlled silica workflow look like?

A controlled workflow prevents dust generation where possible, captures remaining dust and prevents secondary exposure during clean-up.

Relevant direct sources: HSE, HSE.

Silica control is often lost in the sequence, not the theory. Work is planned too late, the right tool is unavailable, the vacuum does not fit the shroud, the water supply is awkward, the exclusion zone is not set and cleaning is rushed.

A good workflow is visible and repeatable. It tells the supervisor what must be ready before work starts, what must be checked during the task and what evidence confirms the area was left clean without exposing other people.

StageControl standardEvidence
PlanAvoid or reduce cutting; choose pre-sized materials or alternative methods where practicable.Design review, procurement note or method decision. HSE
PrepareSelect controlled tool, extraction/water, power arrangements, RPE and exclusion zone.Pre-start checklist and equipment check. HSE
BriefExplain dust health risk, control method, nearby-person protection and stop triggers.Toolbox talk or task briefing. HSE
Stop visible dustPause if dust escapes the shroud, water, extraction or exclusion zone.Stop-work record, defect report or changed method. HSE
Control during workUse water/extraction correctly; keep shrouds, filters and airflow effective.Supervisor observation and defect response. HSE
Protect peopleSegregate, schedule and prevent bystander exposure.Barrier/signage and work sequencing record. HSE
CleanUse suitable vacuum or damp method; prevent dry sweeping.Housekeeping inspection and waste route. HSE
Monitor and surveilUse exposure monitoring and health surveillance where risk and regular exposure require it.Monitoring report, OH programme and competent interpretation. HSE
ReviewRecord defects, visible dust, exposure concerns and worker feedback.Action tracker and assessment update. HSE

Check suitability of all selected RPE and face-fit testing where tight-fitting. A suitable loose-fitting powered alternative is not excluded solely because it does not require a face-seal fit test.

Pre-start evidence should identify the compatible tool, shroud, hose and extractor, the manufacturer’s flow indication/check, filter/container condition, safe emptying method and restart authority. For a wet method, verify sustained water delivery and slurry control. The vacuum class alone does not demonstrate capture at the tool; clean-up attachments and on-tool capture have distinct tasks. Stop for failed extraction, loss of required water or dust escape.

Completed dust-control pre-start record

Fictional completed teaching record for the SHAREhub environment. Values and timings illustrate the decision; they are not site instructions or universal limits. HSE construction dust and RPE selection source source

Combination
Fictional paving-cutting task: supervisor checks the identified cutter, specified shroud, compatible hose and extractor against the manufacturers’ documented combination, not merely the extractor’s class sticker.
Function and condition
The manufacturer-specified flow indication/check is satisfactory; filter, seals and container condition are checked. The record identifies safe emptying with controlled dust release and the trained person responsible.
Alternative wet method
Where the assessed method uses water, verify sustained delivery and slurry control before and during cutting. No universal water rate or airflow is inferred from this example.
Failure and release
A damaged hose connection fails the check: cutting is held. Maintenance replaces the compatible part; the supervisor verifies capture/function and the complete method before authorising restart.
Clean-up
Use the assessed wet or suitable M-/H-class vacuum method and attachment. A cleaning nozzle and on-tool source capture are different functions; neither uncontrolled dry sweeping nor a mask compensates for failed capture.

Apply the learning

A cutting system’s water feed repeatedly stops while the blade runs.

Decision and explanation

Stop the dust-generating task and restore and verify the specified suppression before restart.

The control must work at the dust-generation point throughout the task; wet ground is not evidence of effective suppression.

Lesson 6

On-tool extraction as a system

Capture performance depends on the whole system and task. Suitable dust collection and filtration cannot be inferred from suction noise.

Control RCS exposure while cutting a concrete service chase

Fictional example: a practical application of the existing topic lesson. Setting: A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room. Act: Consider a surface route or off-site prefabrication. Hold / review: Stop for failed extraction, dry sweeping, visible escape, unknown material, unprotected bystanders or RPE not fit for the wearer.

Check extraction flow and capture, position the tool, keep others out, clean with a suitable vacuum or wet method and prevent dust migration. Clean and inspect the area, close defects, review monitoring and release access only after dust control is verified. Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

Visual practice · On-tool extraction as a system

Actual SHAREsimulate construction model context: The operator proposes removing saw protection
Actual SHAREsimulate model capture · The operator proposes removing saw protection. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Control RCS exposure while cutting a concrete service chase

Fictional example: a practical application of the existing topic lesson. Setting: A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room. Act: Consider a surface route or off-site prefabrication. Hold / review: Stop for failed extraction, dry sweeping, visible escape, unknown material, unprotected bystanders or RPE not fit for the wearer.

How should silica dust risk be assessed?

How should silica dust risk be assessed? Assess the material, task energy, duration, enclosure, people exposed, controls and evidence before work starts.Relevant direct sources: HSE. A silica assessment should be task-specific enough to change the work. 'Cutting concrete' is not enough.

How harm develops in the linked model

Contact or ejected material can cause severe injury; wood or silica-containing material dust may cause serious long-term ill health.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should silica dust risk be assessed?

Assess the material, task energy, duration, enclosure, people exposed, controls and evidence before work starts.

Relevant direct sources: HSE.

A silica assessment should be task-specific enough to change the work. 'Cutting concrete' is not enough. The assessor needs to know how much cutting, which tool, whether it is indoors or outside, whether water or extraction is fitted, whether the extraction unit is suitable, who stands nearby, how dust is cleaned up and whether any tight-fitting RPE has been face-fit tested for that wearer, while all selected RPE meets the task’s protection, compatibility and use requirements.

The strongest assessments look at both planned and foreseeable poor conditions. What if water cannot be used because of electrics? What if the vacuum filter blocks? What if a subcontractor brings a dry-cutting tool? What if the task moves indoors? What if a worker has stubble that breaks the mask seal? These practical questions turn silica assessment into risk control.

Assessment factorWhat to askWhy it matters
MaterialDoes the material contain silica and how much is likely?Sandstone, concrete, brick, mortar, granite and engineered stone create different exposures. HSE
TaskIs work cutting, drilling, grinding, polishing, blasting, breaking or sweeping?High-energy tasks generate respirable dust quickly. HSE
MethodCan cutting be avoided, reduced, wet-controlled or extracted?Design and method changes are stronger than PPE. HSE
EnvironmentIs work indoors, enclosed, windy, overhead or near other trades?Dust build-up and spread can change exposure dramatically. HSE
Duration/frequencyHow long and how often will the task occur?Dose accumulates even where each task looks short. HSE
People exposedWho is doing the task and who is nearby?Bystanders, labourers and cleaners can be exposed. HSE
Control evidenceWhat proves water, extraction, RPE and cleaning will work?Controls must be verified before and during work. HSE

Apply the learning

A tool is connected to an improvised domestic vacuum with a poorly fitting hood.

Decision and explanation

Select and verify a suitable compatible tool, capture hood, hose and extraction system.

Capture performance depends on the whole system and task. Suitable dust collection and filtration cannot be inferred from suction noise.

Lesson 7

Protect others and control the spread

Personal protection for one worker does not control secondary exposure, contamination or nearby work.

How does silica dust control differ by sector?

The same health risk appears in different forms across construction, stonework, foundry, quarry, utilities and maintenance work.

Relevant direct sources: HSE.

The control principle is common, but the operational detail changes. A stone workshop needs fixed extraction, segregation and cleaning regimes. A construction site needs sequencing, controlled tools and supervisor checks. A utility team needs mobile controls that work at the excavation or roadside.

This is why a single generic dust assessment is weak. The control standard must fit the sector, task, environment and people exposed.

SectorTypical silica activityControl focus
Construction refurbishmentChasing walls, cutting block, drilling concrete.Avoid cutting, on-tool extraction/water, task-selected RPE (for example FFP3 for high-dust silica work), segregation and clean-up. HSE HSE construction dust and RPE selection
StonemasonryCutting and polishing stone or engineered stone.Wet methods, extraction, enclosure, RPE and health surveillance. HSE
UtilitiesRoad saws, duct cutting and excavation dust.Water suppression, traffic interface, public protection and mobile welfare. HSE
FoundrySand mould handling, shakeout and fettling.Enclosure, LEV, RPE and mixed-dust monitoring. HSE
QuarryingDrilling, crushing and processing stone.Cab filtration, suppression, maintenance and exposure monitoring. HSE
Facilities maintenanceSmall drilling and fixing jobs in older premises.Pre-planning, controlled drilling and vacuum attachment. HSE

A refurbishment team needs portable tool controls, exclusion and a checked hand-back; a production workshop instead needs repeatable source capture, planned cleaning and maintenance across many tasks. In both illustrations the manager tests control effectiveness during real work and reviews exposure evidence after material, tool or layout changes. The same mask or vacuum cannot be selected solely from the word silica. HSE silica task-control context.

Visual practice · Protect others and control the spread

Dust-extracted masonry saw and vacuum at a UK site
SHAREhub photographic illustration · Dust-extracted masonry saw and vacuum at a UK site. Use the written case for the exercise; this image does not prove a defect or safe system.
How does silica dust control differ by sector?

The same health risk appears in different forms across construction, stonework, foundry, quarry, utilities and maintenance work. Relevant direct sources: HSE. The control principle is common, but the operational detail changes. A stone workshop needs fixed extraction, segregation and cleaning regimes.

Where do silica dust controls commonly fail?

Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people. Relevant direct sources: HSE, HSE. The common failure pattern is familiar: the assessment says water suppression or extraction will be used, but the tool arrives without a compatible shroud, the vacuum is not suitable, the water supply is impractical, or the supervisor only checks the paperwork. A strong system checks the physical task.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Where do silica dust controls commonly fail?

Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people.

Relevant direct sources: HSE, HSE.

The common failure pattern is familiar: the assessment says water suppression or extraction will be used, but the tool arrives without a compatible shroud, the vacuum is not suitable, the water supply is impractical, or the supervisor only checks the paperwork.

A strong system checks the physical task. It tests whether the control is in place, usable and effective under the conditions of that job.

Failure or weak practiceHow it developsWhat good looks like
Generic RAMSSame dust controls copied across all tasks.Task-specific method, tool and environment review. HSE
Wrong extractionDomestic or unsuitable vacuum used.Suitable dust-class extraction matched to tool. HSE
Water not practicalWater method written but unavailable or creates other risk.Alternative controlled method planned. HSE
Mask not fit testedFFP3 issued with no fit test or clean-shaven rule.Face fit, user checks and alternative RPE where needed. HSE HSE construction dust and RPE selection
Dusty clothing/welfareContamination carried into vans or welfare.Decontamination, cleaning and changing controls. HSE
Bystanders ignoredOther trades work in the dust zone.Segregation and sequencing. HSE
No surveillance reviewHigh-risk repeated exposure continues without OH process.Health surveillance considered and arranged where required. HSE

Apply the learning

The operator has RPE, but other trades work beside the uncontained cutting area.

Decision and explanation

Control the dust source and spread and protect everyone exposed before continuing.

Personal protection for one worker does not control secondary exposure, contamination or nearby work.

Lesson 8

RPE selection and its limits

RPE is part of a control system. Suitability includes protection, fit, wearer, work, compatibility, use and maintenance.

Adequate and suitable are different questions

RPE must provide the required protection for the substance and task, and be suitable for the wearer, work and environment. Task-specific HSE construction guidance often specifies an APF of 20, for example FFP3 or a half mask with P3 filters, alongside source control. This is not a universal prescription: assess the actual task, duration, other hazards and compatibility, using competent advice where necessary.

Visual practice · RPE selection and its limits

Actual SHAREsimulate construction model context: Dry cutting is proposed without its source control
Actual SHAREsimulate model capture · Dry cutting is proposed without its source control. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Adequate and suitable are different questions

RPE must provide the required protection for the substance and task, and be suitable for the wearer, work and environment. Task-specific HSE construction guidance often specifies an APF of 20, for example FFP3 or a half mask with P3 filters, alongside source control. This is not a universal prescription: assess the actual task, duration, other hazards and compatibility, using competent advice where necessary.

Tight-fitting protection needs a verified fit

A successful fit test relates to the particular wearer and the selected make, model, type and size. A record for another mask is not interchangeable. A pre-use seal check every time a tight-fitting mask is put on is useful, but does not replace the fit test. Training must cover correct donning, limitations, inspection and when to replace or withdraw the equipment.

Where do silica dust controls commonly fail?

Connect the task, the route to the person and the control that can fail. Source / exposure: Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people. Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Tight-fitting protection needs a verified fit

A successful fit test relates to the particular wearer and the selected make, model, type and size. A record for another mask is not interchangeable. A pre-use seal check every time a tight-fitting mask is put on is useful, but does not replace the fit test. Training must cover correct donning, limitations, inspection and when to replace or withdraw the equipment.

Where do silica dust controls commonly fail?

Connect the task, the route to the person and the control that can fail. Source / exposure: Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people. Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?

How can the ISO 45001 hierarchy of controls reduce respirable crystalline silica exposure at source?

Remove or reduce the hazard before relying on procedures or personal protection.

For silica dust, assess the actual task and first look for a way to remove the hazard. Where that is not possible, consider a safer substitute, engineered separation and then clear work procedures. PPE protects against remaining exposure; it does not make an uncontrolled task safe. HSE hierarchy of controls

The selected measures need a named owner, a usable stop point and a check that they still work when the task or conditions change. In Northern Ireland, verify the separate legal route and site instructions.

For the service chase, first test a surface route that avoids cutting. If a substitute material or method is proposed, check all hazards rather than assuming lower silica means safe dust. Where cutting remains necessary, match suppression or extraction to the tool, prevent bystander exposure, control clean-up and select suitable residual RPE. The site manager provides the method and equipment; the supervisor verifies water or airflow and stops when the planned control fails. ERICPD (Eliminate, Reduce, Isolate, Control, PPE, Discipline) is a teaching prompt here; Discipline means keeping controls effective through checking and learning. HSE topic-specific control sequence.

How can the ERICPD hierarchy of controls reduce respirable crystalline silica exposure at source?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Control RCS exposure while cutting a concrete service chase
Activity and exposure
A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room.
Before work
Consider a surface route or off-site prefabrication. If cutting remains necessary, fit effective on-tool extraction with an appropriate M/H-class unit or suitable water suppression, segregate the area and select residual RPE.
During the activity
Check extraction flow and capture, position the tool, keep others out, clean with a suitable vacuum or wet method and prevent dust migration.
Hold or stop
Stop for failed extraction, dry sweeping, visible escape, unknown material, unprotected bystanders or RPE not fit for the wearer.
Hand-back and release
Clean and inspect the area, close defects, review monitoring and release access only after dust control is verified.
Evidence to retain
Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back.
Decision owner
Site manager with competent cutter and occupational hygienist
Full example
Read the activity, checks and hand-back in context
ERICPD control levelTopic-specific exampleSource and full task context
Eliminate

Assess a surface service route that avoids cutting.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Reduce

Check all hazards of a proposed substitute material or method.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Isolate

Match suppression or extraction to the tool and separate bystanders.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Control

Control clean-up and provide the assessed equipment and method.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
PPE

Select suitable residual RPE.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Discipline

Verify water or airflow and stop when the planned control fails.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence

How can the ISO 45001 hierarchy of controls reduce respirable crystalline silica exposure at source?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Control RCS exposure while cutting a concrete service chase
Activity and exposure
A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room.
Before work
Consider a surface route or off-site prefabrication. If cutting remains necessary, fit effective on-tool extraction with an appropriate M/H-class unit or suitable water suppression, segregate the area and select residual RPE.
During the activity
Check extraction flow and capture, position the tool, keep others out, clean with a suitable vacuum or wet method and prevent dust migration.
Hold or stop
Stop for failed extraction, dry sweeping, visible escape, unknown material, unprotected bystanders or RPE not fit for the wearer.
Hand-back and release
Clean and inspect the area, close defects, review monitoring and release access only after dust control is verified.
Evidence to retain
Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back.
Decision owner
Site manager with competent cutter and occupational hygienist
Full example
Read the activity, checks and hand-back in context
Five-level control stage(s)Topic-specific exampleSource and full task context
Elimination

Assess a surface service route that avoids cutting.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Substitution

Check all hazards of a proposed substitute material or method.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Engineering controls

Match suppression or extraction to the tool and separate bystanders.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Administrative controls

Control clean-up and provide the assessed equipment and method.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
PPE

Select suitable residual RPE.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence
Administrative controls

Verify water or airflow and stop when the planned control fails.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE topic-specific control sequence

Apply the learning

A supervisor proposes RPE as the only answer to uncontrolled indoor cutting.

Decision and explanation

Review source controls and select suitable RPE for the residual assessed exposure.

RPE is part of a control system. Suitability includes protection, fit, wearer, work, compatibility, use and maintenance.

Lesson 9

Fit testing and everyday use

Fit testing and a fit check have different purposes. Tight-fitting facepieces need a suitable seal whenever worn; select alternatives competently where needed.

Facial hair changes the decision

Hair in the sealing area can prevent a good seal. Do not improvise by tightening straps or assuming a high filter rating compensates for leakage. Where a tight fit cannot be achieved, assess a suitable alternative that does not rely on that seal, such as an appropriate loose-fitting powered hood. Adequacy, compatibility, maintenance and user training still have to be addressed.

Visual practice · Fit testing and everyday use

Dust-extracted masonry saw and vacuum at a UK site
SHAREhub photographic illustration · Dust-extracted masonry saw and vacuum at a UK site. Use the written case for the exercise; this image does not prove a defect or safe system.
Facial hair changes the decision

Hair in the sealing area can prevent a good seal. Do not improvise by tightening straps or assuming a high filter rating compensates for leakage. Where a tight fit cannot be achieved, assess a suitable alternative that does not rely on that seal, such as an appropriate loose-fitting powered hood. Adequacy, compatibility, maintenance and user training still have to be addressed.

Keep the controls connected

Suitable RPE may be needed for residual dust even with water or extraction. It does not control what other people breathe and must not become an excuse to abandon source control. A source-control defect and a wearer-fit defect are separate problems; resolving one does not automatically resolve the other.

What do people commonly get wrong about silica dust?

Common misunderstandings usually underestimate invisible dust, short tasks, clean-up exposure and RPE limitations. Relevant direct sources: HSE. Silica dust is dangerous partly because it does not look dramatic. A small haze, dusty clothing or powder on a sill can be treated as mess rather than evidence of airborne exposure.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Keep the controls connected

Suitable RPE may be needed for residual dust even with water or extraction. It does not control what other people breathe and must not become an excuse to abandon source control. A source-control defect and a wearer-fit defect are separate problems; resolving one does not automatically resolve the other.

What do people commonly get wrong about silica dust?

Common misunderstandings usually underestimate invisible dust, short tasks, clean-up exposure and RPE limitations.

Relevant direct sources: HSE.

Silica dust is dangerous partly because it does not look dramatic. A small haze, dusty clothing or powder on a sill can be treated as mess rather than evidence of airborne exposure. Workers may also believe outdoor work is automatically safe, or that a mask alone is enough.

The best training uses specific mistakes. It shows why dry sweeping is stopped, why vacuum class matters, why stubble can defeat a tight-fitting mask and why other trades must be protected.

MisunderstandingRealityTeaching point
Only visible clouds matter.RCS may be too fine to see under normal light.Control the task, not just visible dust. HSE
A short cut is low risk.Repeated short cuts create cumulative dose.Plan all high-energy silica tasks. HSE
Outdoor work is safe.Wind direction and breathing-zone exposure still matter.Use controls outdoors too. HSE
Any vacuum will do.Fine dust can pass through unsuitable equipment.Use suitable dust-class extraction and maintain it. HSE
FFP3 solves the problem.RPE depends on fit, wear time, compatibility and user behaviour.Use RPE as part of a control package. HSE HSE construction dust and RPE selection
Cleaning happens after exposure ends.Dry sweeping can be a high-exposure task.Control clean-up as part of the job. HSE

Where do silica dust controls commonly fail?

Connect the task, the route to the person and the control that can fail. Source / exposure: Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people. Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people. Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?

Apply the learning

A tight-fitting respirator leaks around facial hair despite a previous fit-test record.

Decision and explanation

Do not rely on that seal; arrange suitable protection and task controls before exposure.

Fit testing and a fit check have different purposes. Tight-fitting facepieces need a suitable seal whenever worn; select alternatives competently where needed.

Lesson 10

Clean without re-aerosolising dust

Cleaning can create a fresh exposure. Prevent accumulated dust becoming airborne and control handling and disposal.

Choose controls for silica dust

Start with the stronger practicable options and verify their effect. Eliminate: Assess a surface service route that avoids cutting. Reduce: Check all hazards of a proposed substitute material or method. Isolate: Match suppression or extraction to the tool and separate bystanders.

Control: Control clean-up and provide the assessed equipment and method. PPE: Select suitable residual RPE. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

Visual practice · Clean without re-aerosolising dust

Actual SHAREsimulate construction model context: Dry cutting is proposed without its source control
Actual SHAREsimulate model capture · Dry cutting is proposed without its source control. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Choose controls for silica dust

Start with the stronger practicable options and verify their effect. Eliminate: Assess a surface service route that avoids cutting. Reduce: Check all hazards of a proposed substitute material or method. Isolate: Match suppression or extraction to the tool and separate bystanders.

What does a controlled silica workflow look like?

What does a controlled silica workflow look like? A controlled workflow prevents dust generation where possible, captures remaining dust and prevents secondary exposure during clean-up.Relevant direct sources: HSE, HSE. Silica control is often lost in the sequence, not the theory. Work is planned too late, the right tool is unavailable, the vacuum does not fit the shroud, the water supply is awkward, the exclusion zone is not set and cleaning is rushed.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What does a controlled silica workflow look like?

A controlled workflow prevents dust generation where possible, captures remaining dust and prevents secondary exposure during clean-up.

Relevant direct sources: HSE, HSE.

Silica control is often lost in the sequence, not the theory. Work is planned too late, the right tool is unavailable, the vacuum does not fit the shroud, the water supply is awkward, the exclusion zone is not set and cleaning is rushed.

A good workflow is visible and repeatable. It tells the supervisor what must be ready before work starts, what must be checked during the task and what evidence confirms the area was left clean without exposing other people.

StageControl standardEvidence
PlanAvoid or reduce cutting; choose pre-sized materials or alternative methods where practicable.Design review, procurement note or method decision. HSE
PrepareSelect controlled tool, extraction/water, power arrangements, RPE and exclusion zone.Pre-start checklist and equipment check. HSE
BriefExplain dust health risk, control method, nearby-person protection and stop triggers.Toolbox talk or task briefing. HSE
Stop visible dustPause if dust escapes the shroud, water, extraction or exclusion zone.Stop-work record, defect report or changed method. HSE
Control during workUse water/extraction correctly; keep shrouds, filters and airflow effective.Supervisor observation and defect response. HSE
Protect peopleSegregate, schedule and prevent bystander exposure.Barrier/signage and work sequencing record. HSE
CleanUse suitable vacuum or damp method; prevent dry sweeping.Housekeeping inspection and waste route. HSE
Monitor and surveilUse exposure monitoring and health surveillance where risk and regular exposure require it.Monitoring report, OH programme and competent interpretation. HSE
ReviewRecord defects, visible dust, exposure concerns and worker feedback.Action tracker and assessment update. HSE

Check suitability of all selected RPE and face-fit testing where tight-fitting. A suitable loose-fitting powered alternative is not excluded solely because it does not require a face-seal fit test.

Pre-start evidence should identify the compatible tool, shroud, hose and extractor, the manufacturer’s flow indication/check, filter/container condition, safe emptying method and restart authority. For a wet method, verify sustained water delivery and slurry control. The vacuum class alone does not demonstrate capture at the tool; clean-up attachments and on-tool capture have distinct tasks. Stop for failed extraction, loss of required water or dust escape.

Completed dust-control pre-start record

Fictional completed teaching record for the SHAREhub environment. Values and timings illustrate the decision; they are not site instructions or universal limits. HSE construction dust and RPE selection source source

Combination
Fictional paving-cutting task: supervisor checks the identified cutter, specified shroud, compatible hose and extractor against the manufacturers’ documented combination, not merely the extractor’s class sticker.
Function and condition
The manufacturer-specified flow indication/check is satisfactory; filter, seals and container condition are checked. The record identifies safe emptying with controlled dust release and the trained person responsible.
Alternative wet method
Where the assessed method uses water, verify sustained delivery and slurry control before and during cutting. No universal water rate or airflow is inferred from this example.
Failure and release
A damaged hose connection fails the check: cutting is held. Maintenance replaces the compatible part; the supervisor verifies capture/function and the complete method before authorising restart.
Clean-up
Use the assessed wet or suitable M-/H-class vacuum method and attachment. A cleaning nozzle and on-tool source capture are different functions; neither uncontrolled dry sweeping nor a mask compensates for failed capture.

Apply the learning

Dry sweeping creates a dust cloud after the cutting has finished.

Decision and explanation

Stop the dusty cleanup and use the suitable controlled cleaning and waste method.

Cleaning can create a fresh exposure. Prevent accumulated dust becoming airborne and control handling and disposal.

Lesson 11

Maintain, check and investigate controls

Daily checks, defect response and required thorough examination serve different purposes; none makes a known failed control acceptable.

Where do silica dust controls commonly fail?

Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people.

Relevant direct sources: HSE, HSE.

The common failure pattern is familiar: the assessment says water suppression or extraction will be used, but the tool arrives without a compatible shroud, the vacuum is not suitable, the water supply is impractical, or the supervisor only checks the paperwork.

A strong system checks the physical task. It tests whether the control is in place, usable and effective under the conditions of that job.

Failure or weak practiceHow it developsWhat good looks like
Generic RAMSSame dust controls copied across all tasks.Task-specific method, tool and environment review. HSE
Wrong extractionDomestic or unsuitable vacuum used.Suitable dust-class extraction matched to tool. HSE
Water not practicalWater method written but unavailable or creates other risk.Alternative controlled method planned. HSE
Mask not fit testedFFP3 issued with no fit test or clean-shaven rule.Face fit, user checks and alternative RPE where needed. HSE HSE construction dust and RPE selection
Dusty clothing/welfareContamination carried into vans or welfare.Decontamination, cleaning and changing controls. HSE
Bystanders ignoredOther trades work in the dust zone.Segregation and sequencing. HSE
No surveillance reviewHigh-risk repeated exposure continues without OH process.Health surveillance considered and arranged where required. HSE

Visual practice · Maintain, check and investigate controls

Dust-extracted masonry saw and vacuum at a UK site
SHAREhub photographic illustration · Dust-extracted masonry saw and vacuum at a UK site. Use the written case for the exercise; this image does not prove a defect or safe system.
Where do silica dust controls commonly fail?

Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people. Relevant direct sources: HSE, HSE. The common failure pattern is familiar: the assessment says water suppression or extraction will be used, but the tool arrives without a compatible shroud, the vacuum is not suitable, the water supply is impractical, or the supervisor only checks the paperwork. A strong system checks the physical task.

How should silica dust controls be assured?

Assurance should focus on live work: dust generation, control use, RPE, housekeeping and worker understanding. Relevant direct sources: HSE. A good silica assurance check starts at the workface. The reviewer should watch how the tool is used, whether dust escapes, how RPE is worn, whether other people are exposed and how dust is cleaned afterwards.

How harm develops in the linked model

Contact or ejected material can cause severe injury; wood or silica-containing material dust may cause serious long-term ill health.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should silica dust controls be assured?

Assurance should focus on live work: dust generation, control use, RPE, housekeeping and worker understanding.

Relevant direct sources: HSE.

A good silica assurance check starts at the workface. The reviewer should watch how the tool is used, whether dust escapes, how RPE is worn, whether other people are exposed and how dust is cleaned afterwards.

Second-line reviews should test whether the organisation understands its silica risk profile, not just whether individual RAMS exist. Third-line or specialist support may be needed for repeated high-risk work, exposure monitoring strategy or health surveillance governance.

Assurance layerWhat to checkExample question
First lineTool, extraction, water, RPE and exclusion before and during work.Would this task create visible or invisible dust outside control? HSE
Second lineAssessment quality, equipment availability, face fit and action closure.Are high-dust tasks sampled against real work? HSE
Third lineOccupational hygiene strategy, surveillance and governance.Do monitoring and surveillance results change the control plan? HSE
Worker voicePractical barriers and symptom reporting.Can workers stop dusty work without pressure? HSE
Leadership reviewTrends, resourcing and repeated failures.Are dust controls funded and available before work starts? HSE

Apply the learning

A hose is split and the extraction warning has been ignored for several shifts.

Decision and explanation

Stop affected work, repair the fault and verify performance through the maintenance system.

Daily checks, defect response and required thorough examination serve different purposes; none makes a known failed control acceptable.

Lesson 12

Monitoring and health surveillance

Air monitoring helps evaluate exposure; health surveillance seeks early health effects. They answer different questions and neither substitutes for prevention.

How do WELs, monitoring and health surveillance fit together?

The WEL helps define legal exposure control, while monitoring and surveillance test whether controls are adequate and health is being protected.

Relevant direct sources: HSE, HSE.

HSE states the WEL for RCS is 0.1 mg/m3 as an 8-hour TWA. That number should not be used as permission to create dusty work. COSHH requires exposure to be prevented or adequately controlled, and for carcinogens and asthmagens exposure must be controlled to as low as reasonably practicable.

Air monitoring is useful where exposure is uncertain, control effectiveness needs proof or high-risk work is repeated. Health surveillance is required where workers are regularly exposed to RCS and there is a reasonable likelihood that silicosis may develop. Both need competent interpretation and should drive control improvement.

ElementWhat it doesWhat it does not do
WELSets a legal airborne exposure limit over a reference period.Does not prove work is well controlled if exposure is just below the limit. HSE
Exposure monitoringMeasures representative breathing-zone exposure during tasks.Does not replace engineering control or supervision.
Health surveillanceLooks for early signs of work-related ill health where legally/clinically appropriate.Does not make exposure acceptable.
RPE face fitChecks tight-fitting mask seal for the wearer.Does not compensate for cutting without the specified effective dust controls or poor extraction.
LEV/TExTChecks extraction remains effective over time.Does not prove users position the hood correctly every time.

EH40 identifies the substance limit and averaging period. The surveillance guide supports the RCS health-surveillance trigger; INDG463 supports source control and suitable RPE. The table’s monitoring, fit and extraction checks are complementary controls, not separate requirements established by EH40 alone. Select and verify the actual equipment and programme with competent advice. HSE RCS surveillance trigger; HSE silica control and worker protection.

Visual practice · Monitoring and health surveillance

Actual SHAREsimulate construction model context: Dry cutting is proposed without its source control
Actual SHAREsimulate model capture · Dry cutting is proposed without its source control. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
How do WELs, monitoring and health surveillance fit together?

The WEL helps define legal exposure control, while monitoring and surveillance test whether controls are adequate and health is being protected. Relevant direct sources: HSE, HSE. HSE states the WEL for RCS is 0.1 mg/m3 as an 8-hour TWA. That number should not be used as permission to create dusty work.

Use the full silica dust lesson

Follow the official sources below and retain the task-specific evidence. Official guidance: source Official guidance: HSE construction dust and RPE selection Task decision: Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back. Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Use the full silica dust lesson

Follow the official sources below and retain the task-specific evidence. Official guidance: source Official guidance: HSE construction dust and RPE selection Task decision: Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back. Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction.

Apply it: Which official source and full-topic section will you use to resolve the next decision?

Apply the learning

A manager wants lung health checks to replace exposure assessment and control verification.

Decision and explanation

Use exposure assessment and control verification, with health surveillance where indicated as an additional arrangement.

Air monitoring helps evaluate exposure; health surveillance seeks early health effects. They answer different questions and neither substitutes for prevention.

Lesson 13

Understand exposure limits and uncertainty

Exposure evidence has a scope. Control exposure adequately and reduce it through suitable measures rather than treating a single result as universal permission.

How do WELs, monitoring and health surveillance fit together?

The WEL helps define legal exposure control, while monitoring and surveillance test whether controls are adequate and health is being protected.

Relevant direct sources: HSE, HSE.

HSE states the WEL for RCS is 0.1 mg/m3 as an 8-hour TWA. That number should not be used as permission to create dusty work. COSHH requires exposure to be prevented or adequately controlled, and for carcinogens and asthmagens exposure must be controlled to as low as reasonably practicable.

Air monitoring is useful where exposure is uncertain, control effectiveness needs proof or high-risk work is repeated. Health surveillance is required where workers are regularly exposed to RCS and there is a reasonable likelihood that silicosis may develop. Both need competent interpretation and should drive control improvement.

ElementWhat it doesWhat it does not do
WELSets a legal airborne exposure limit over a reference period.Does not prove work is well controlled if exposure is just below the limit. HSE
Exposure monitoringMeasures representative breathing-zone exposure during tasks.Does not replace engineering control or supervision.
Health surveillanceLooks for early signs of work-related ill health where legally/clinically appropriate.Does not make exposure acceptable.
RPE face fitChecks tight-fitting mask seal for the wearer.Does not compensate for cutting without the specified effective dust controls or poor extraction.
LEV/TExTChecks extraction remains effective over time.Does not prove users position the hood correctly every time.

EH40 identifies the substance limit and averaging period. The surveillance guide supports the RCS health-surveillance trigger; INDG463 supports source control and suitable RPE. The table’s monitoring, fit and extraction checks are complementary controls, not separate requirements established by EH40 alone. Select and verify the actual equipment and programme with competent advice. HSE RCS surveillance trigger; HSE silica control and worker protection.

Visual practice · Understand exposure limits and uncertainty

Dust-extracted masonry saw and vacuum at a UK site
SHAREhub photographic illustration · Dust-extracted masonry saw and vacuum at a UK site. Use the written case for the exercise; this image does not prove a defect or safe system.
How do WELs, monitoring and health surveillance fit together?

The WEL helps define legal exposure control, while monitoring and surveillance test whether controls are adequate and health is being protected. Relevant direct sources: HSE, HSE. HSE states the WEL for RCS is 0.1 mg/m3 as an 8-hour TWA. That number should not be used as permission to create dusty work.

Which legal duties and guidance apply in Great Britain and Northern Ireland?

The RCS workplace exposure limit is 0.1 mg/m³ as an eight-hour time-weighted average in both GB and NI, but it is not a safe target. Prevent or control the dust at source, keep exposure below the limit and reduce carcinogenic exposure as low as reasonably practicable. For an individual task, verify the material, process, exposure route, people affected and control effectiveness before using the applicable row.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Which legal duties and guidance apply in Great Britain and Northern Ireland?

The RCS workplace exposure limit is 0.1 mg/m³ as an eight-hour time-weighted average in both GB and NI, but it is not a safe target. Prevent or control the dust at source, keep exposure below the limit and reduce carcinogenic exposure as low as reasonably practicable.

For an individual task, verify the material, process, exposure route, people affected and control effectiveness before using the applicable row.

JurisdictionRouteDirect sourcesDecision supported
Great BritainGB COSHHControl of Substances Hazardous to Health Regulations 2002; INDG463 control of exposure to silica dust, 2024Assess RCS generation and use effective source controls before work.
Northern IrelandNI COSHHControl of Substances Hazardous to Health Regulations (Northern Ireland) 2003; Silica dust in Northern IrelandUse the separate NI hazardous-substances instrument and NI silica guidance.
Great BritainGB RCS WELEH40/2005 workplace exposure limits, 2020 edition; INDG463 control of exposure to silica dust, 20240.1 mg/m³ respirable fraction, eight-hour TWA; below the WEL is not automatic adequate control.
Northern IrelandNI RCS WELNI approval of EH40/2005; Silica dust in Northern IrelandNI-approved EH40: 0.1 mg/m³, eight-hour TWA; reduce exposure as low as reasonably practicable.
Great BritainHealth surveillanceRCS health surveillance for occupational health professionals, amended May 2026; Silicosis causes and risk controlsProvide surveillance where regular RCS exposure creates reasonable likelihood of silicosis.

Apply the learning

One short sample is proposed as clearance for every future material, tool and shift.

Decision and explanation

Have a competent person assess representativeness and controls across relevant tasks and conditions.

Exposure evidence has a scope. Control exposure adequately and reduce it through suitable measures rather than treating a single result as universal permission.

Lesson 14

Brief the method and stop triggers

People need task-specific information and the confidence to stop a failing control, including arrangements affecting nearby trades.

What should each role learn and demonstrate?

Competence requires a person to select and use the right control for a real dust or fume task, recognise failure and act before exposure continues.

HSE supports the control principle. Assess a realistic task, record observation and reassess after material, equipment or health findings change.

RoleLearningDemonstrationAssessor recordReassess when
Cutter/operatorIdentify RCS tasks, material and control failure.Set tool extraction or water and stop when it fails.Observed task and control check.At tool/material/site change.
SupervisorProtect bystanders and verify the workface.Reject dry sweeping or unprotected dust escape.Workface observation and defect close-out.After change or near miss.
Equipment maintainerMaintain extraction, filters and water feed.Demonstrate capture and safe filter handling.Maintenance and test record.At service interval or defect.
Safety adviser/hygienistPlan exposure assessment and WEL interpretation.Explain eight-hour TWA and why below WEL is not enough.Sampling plan and control decision.At process or material change.
Occupational-health adviserApply risk-based surveillance confidentially.Explain trigger, referral and record boundary.Restricted health programme record.When risk or health findings change.

Visual practice · Brief the method and stop triggers

Actual SHAREsimulate construction model context: Dry cutting is proposed without its source control
Actual SHAREsimulate model capture · Dry cutting is proposed without its source control. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
What should each role learn and demonstrate?

Competence requires a person to select and use the right control for a real dust or fume task, recognise failure and act before exposure continues. HSE supports the control principle. Assess a realistic task, record observation and reassess after material, equipment or health findings change.

What evidence shows silica dust is being controlled?

Evidence should prove that high-dust tasks are designed, controlled, briefed, inspected, cleaned and reviewed. Relevant direct sources: UK legislation, HSE. The evidence pack should show control in the real task, not just a signed method statement. It should include the task-specific assessment, equipment checks, RPE fit records, supervisor observations, cleaning records, exposure monitoring where needed and health surveillance arrangements.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What evidence shows silica dust is being controlled?

Evidence should prove that high-dust tasks are designed, controlled, briefed, inspected, cleaned and reviewed.

Relevant direct sources: UK legislation, HSE.

The evidence pack should show control in the real task, not just a signed method statement. It should include the task-specific assessment, equipment checks, RPE fit records, supervisor observations, cleaning records, exposure monitoring where needed and health surveillance arrangements.

Where silica exposure is a significant organisational risk, leaders should see leading indicators: uncontrolled dust events, extraction defects, face-fit compliance, worker concerns, monitoring results and overdue actions.

Evidence itemWhat it should showAssurance question
Risk assessment or technical assessmentScope, task, people exposed, route of exposure, existing controls, further controls, owner and review trigger.Does it match the real work, location, materials, people and abnormal conditions? UK legislation
Action trackerAction, owner, priority, due date, interim control and close-out evidence.Are serious-risk actions verified at the workplace before closure? UK legislation
Training and briefing recordsWho was trained, what they were trained on, how competence was checked and when refresh is due.Can people explain the health risk, controls and stop triggers? UK legislation
Inspection and maintenance recordsChecks on LEV, extraction, RPE, guards, welfare, permits, isolation or other critical controls.Are defects corrected before exposure or interface risk continues? UK legislation
Monitoring and surveillance recordsExposure monitoring, health surveillance status, anonymised trends and competent interpretation where relevant.Are results linked back to control review and work design? UK legislation
Incident, near-miss and concern recordsReported symptoms, dust clouds, exposure events, permit clashes, dermatitis signs or weak signals.Are early warnings investigated before harm becomes irreversible? UK legislation
Management reviewTrends, resources, assurance confidence, overdue actions and decisions.Are leaders reviewing control effectiveness rather than activity counts alone? UK legislation
Tool and extraction registerControlled tools, shrouds, vacuums, filters and maintenance.Are tools matched to the task and inspected? UK legislation
RPE fit-test registerWho is face-fit tested for which mask and when review is needed.Is the issued mask the same model as the fit test? UK legislation
Silica task inventoryTasks, materials, frequency, controls and surveillance triggers.Are repeated short tasks captured? UK legislation
Exposure monitoringRepresentative sampling and competent interpretation where needed.Do results lead to control improvements? UK legislation

Apply the learning

An agency worker is asked to cut without knowing the extraction warning or cleanup method.

Decision and explanation

Brief and verify the task, controls, checks, stop triggers and reporting route before work.

People need task-specific information and the confidence to stop a failing control, including arrangements affecting nearby trades.

Lesson 15

Respond to failure and protect people

The immediate priority is preventing exposure. Do not improvise dust disturbance or rescue into an uncontrolled atmosphere.

When should silica work stop or escalate?

Stop or escalate where silica-containing work is uncontrolled, dusty, unplanned, poorly supervised or not matched to the assessment.

Relevant direct sources: HSE.

Silica stop triggers should be clear enough for a worker or supervisor to act immediately. If visible dust escapes, extraction fails, water supply is lost, tight-fitting RPE has not been face-fit tested, the work moves indoors or other trades are exposed, the job should pause until controls are restored or the method is redesigned.

Escalation is not failure. It is good management. High-dust work often needs better equipment, revised sequencing, occupational hygiene advice or client/design decisions that a worker cannot make alone.

TriggerWhy it mattersAction
Uncontrolled cutting or grinding starts without the specified effective dust-control systemHigh RCS generation likely.Stop and apply designed water/extraction controls or redesign. HSE
Visible dust escapes controlControls are not capturing the hazard.Pause, check tool, shroud, vacuum, water and work position. HSE
No suitable RPE, or missing face fit where RPE is tight-fittingResidual exposure may be uncontrolled.Do not proceed until suitable RPE controls are in place. HSE
Dry sweeping or compressed air cleaningSettled dust becomes airborne again.Use suitable vacuum or damp method. HSE
Nearby workers/public exposedBystander exposure is being ignored.Segregate, reschedule or enclose the task. HSE
Repeated dusty tasksCumulative exposure and surveillance duties may apply.Review COSHH, monitoring and health surveillance. HSE

Visual practice · Respond to failure and protect people

Dust-extracted masonry saw and vacuum at a UK site
SHAREhub photographic illustration · Dust-extracted masonry saw and vacuum at a UK site. Use the written case for the exercise; this image does not prove a defect or safe system.
When should silica work stop or escalate?

Stop or escalate where silica-containing work is uncontrolled, dusty, unplanned, poorly supervised or not matched to the assessment. Relevant direct sources: HSE. Silica stop triggers should be clear enough for a worker or supervisor to act immediately. If visible dust escapes, extraction fails, water supply is lost, tight-fitting RPE has not been face-fit tested, the work moves indoors or other trades are exposed, the job should pause until controls are restored or the method is redesigned.

Where do silica dust controls commonly fail?

Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people. Relevant direct sources: HSE, HSE. The common failure pattern is familiar: the assessment says water suppression or extraction will be used, but the tool arrives without a compatible shroud, the vacuum is not suitable, the water supply is impractical, or the supervisor only checks the paperwork. A strong system checks the physical task.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Where do silica dust controls commonly fail?

Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people.

Relevant direct sources: HSE, HSE.

The common failure pattern is familiar: the assessment says water suppression or extraction will be used, but the tool arrives without a compatible shroud, the vacuum is not suitable, the water supply is impractical, or the supervisor only checks the paperwork.

A strong system checks the physical task. It tests whether the control is in place, usable and effective under the conditions of that job.

Failure or weak practiceHow it developsWhat good looks like
Generic RAMSSame dust controls copied across all tasks.Task-specific method, tool and environment review. HSE
Wrong extractionDomestic or unsuitable vacuum used.Suitable dust-class extraction matched to tool. HSE
Water not practicalWater method written but unavailable or creates other risk.Alternative controlled method planned. HSE
Mask not fit testedFFP3 issued with no fit test or clean-shaven rule.Face fit, user checks and alternative RPE where needed. HSE HSE construction dust and RPE selection
Dusty clothing/welfareContamination carried into vans or welfare.Decontamination, cleaning and changing controls. HSE
Bystanders ignoredOther trades work in the dust zone.Segregation and sequencing. HSE
No surveillance reviewHigh-risk repeated exposure continues without OH process.Health surveillance considered and arranged where required. HSE

Apply the learning

A dense cloud appears when the extractor disconnects and people remain in the room.

Decision and explanation

Stop the task, keep people out of the affected exposure and apply the site’s controlled response before investigation and restart.

The immediate priority is preventing exposure. Do not improvise dust disturbance or rescue into an uncontrolled atmosphere.

Lesson 16

Audit evidence rather than paperwork

Assurance traces records to the real equipment and task. A document can be genuine while irrelevant to the current exposure.

What evidence shows silica dust is being controlled?

Evidence should prove that high-dust tasks are designed, controlled, briefed, inspected, cleaned and reviewed.

Relevant direct sources: UK legislation, HSE.

The evidence pack should show control in the real task, not just a signed method statement. It should include the task-specific assessment, equipment checks, RPE fit records, supervisor observations, cleaning records, exposure monitoring where needed and health surveillance arrangements.

Where silica exposure is a significant organisational risk, leaders should see leading indicators: uncontrolled dust events, extraction defects, face-fit compliance, worker concerns, monitoring results and overdue actions.

Evidence itemWhat it should showAssurance question
Risk assessment or technical assessmentScope, task, people exposed, route of exposure, existing controls, further controls, owner and review trigger.Does it match the real work, location, materials, people and abnormal conditions? UK legislation
Action trackerAction, owner, priority, due date, interim control and close-out evidence.Are serious-risk actions verified at the workplace before closure? UK legislation
Training and briefing recordsWho was trained, what they were trained on, how competence was checked and when refresh is due.Can people explain the health risk, controls and stop triggers? UK legislation
Inspection and maintenance recordsChecks on LEV, extraction, RPE, guards, welfare, permits, isolation or other critical controls.Are defects corrected before exposure or interface risk continues? UK legislation
Monitoring and surveillance recordsExposure monitoring, health surveillance status, anonymised trends and competent interpretation where relevant.Are results linked back to control review and work design? UK legislation
Incident, near-miss and concern recordsReported symptoms, dust clouds, exposure events, permit clashes, dermatitis signs or weak signals.Are early warnings investigated before harm becomes irreversible? UK legislation
Management reviewTrends, resources, assurance confidence, overdue actions and decisions.Are leaders reviewing control effectiveness rather than activity counts alone? UK legislation
Tool and extraction registerControlled tools, shrouds, vacuums, filters and maintenance.Are tools matched to the task and inspected? UK legislation
RPE fit-test registerWho is face-fit tested for which mask and when review is needed.Is the issued mask the same model as the fit test? UK legislation
Silica task inventoryTasks, materials, frequency, controls and surveillance triggers.Are repeated short tasks captured? UK legislation
Exposure monitoringRepresentative sampling and competent interpretation where needed.Do results lead to control improvements? UK legislation

Visual practice · Audit evidence rather than paperwork

Actual SHAREsimulate construction model context: The operator proposes removing saw protection
Actual SHAREsimulate model capture · The operator proposes removing saw protection. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
What evidence shows silica dust is being controlled?

Evidence should prove that high-dust tasks are designed, controlled, briefed, inspected, cleaned and reviewed. Relevant direct sources: UK legislation, HSE. The evidence pack should show control in the real task, not just a signed method statement. It should include the task-specific assessment, equipment checks, RPE fit records, supervisor observations, cleaning records, exposure monitoring where needed and health surveillance arrangements.

How should silica dust controls be assured?

Assurance should focus on live work: dust generation, control use, RPE, housekeeping and worker understanding. Relevant direct sources: HSE. A good silica assurance check starts at the workface. The reviewer should watch how the tool is used, whether dust escapes, how RPE is worn, whether other people are exposed and how dust is cleaned afterwards.

How harm develops in the linked model

Contact or ejected material can cause severe injury; wood or silica-containing material dust may cause serious long-term ill health.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should silica dust controls be assured?

Assurance should focus on live work: dust generation, control use, RPE, housekeeping and worker understanding.

Relevant direct sources: HSE.

A good silica assurance check starts at the workface. The reviewer should watch how the tool is used, whether dust escapes, how RPE is worn, whether other people are exposed and how dust is cleaned afterwards.

Second-line reviews should test whether the organisation understands its silica risk profile, not just whether individual RAMS exist. Third-line or specialist support may be needed for repeated high-risk work, exposure monitoring strategy or health surveillance governance.

Assurance layerWhat to checkExample question
First lineTool, extraction, water, RPE and exclusion before and during work.Would this task create visible or invisible dust outside control? HSE
Second lineAssessment quality, equipment availability, face fit and action closure.Are high-dust tasks sampled against real work? HSE
Third lineOccupational hygiene strategy, surveillance and governance.Do monitoring and surveillance results change the control plan? HSE
Worker voicePractical barriers and symptom reporting.Can workers stop dusty work without pressure? HSE
Leadership reviewTrends, resourcing and repeated failures.Are dust controls funded and available before work starts? HSE

Apply the learning

The maintenance register says serviced but the tool, hose and extractor IDs do not match the workface.

Decision and explanation

Reconcile the actual system, performance evidence, defects and actions before accepting the control.

Assurance traces records to the real equipment and task. A document can be genuine while irrelevant to the current exposure.

Lesson 17

Capstone: a defensible restart

Several changes can alter exposure together. A repair alone does not validate the revised work arrangement.

How should a concrete cutting task be controlled?

A worked task example shows how silica dust control should be planned, checked and evidenced at the workface.

Visual practice · Capstone: a defensible restart

Dust-extracted masonry saw and vacuum at a UK site
SHAREhub photographic illustration · Dust-extracted masonry saw and vacuum at a UK site. Use the written case for the exercise; this image does not prove a defect or safe system.
How should a concrete cutting task be controlled?

How should a concrete cutting task be controlled? A worked task example shows how silica dust control should be planned, checked and evidenced at the workface.Control RCS exposure while cutting a concrete service chaseTask material and setting: A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room.People and prerequisites: The site manager owns the work; the cutter checks material, other occupants, tool and extraction compatibility; a competent adviser plans exposure verification where needed.Before: Consider a surface route or off-site prefabrication.

When should silica work stop or escalate?

Stop or escalate where silica-containing work is uncontrolled, dusty, unplanned, poorly supervised or not matched to the assessment. Relevant direct sources: HSE. Silica stop triggers should be clear enough for a worker or supervisor to act immediately. If visible dust escapes, extraction fails, water supply is lost, tight-fitting RPE has not been face-fit tested, the work moves indoors or other trades are exposed, the job should pause until controls are restored or the method is redesigned.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Control RCS exposure while cutting a concrete service chase

Task material and setting: A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room.

People and prerequisites: The site manager owns the work; the cutter checks material, other occupants, tool and extraction compatibility; a competent adviser plans exposure verification where needed.

Before: Consider a surface route or off-site prefabrication. If cutting remains necessary, fit effective on-tool extraction with an appropriate M/H-class unit or suitable water suppression, segregate the area and select residual RPE.

During: Check extraction flow and capture, position the tool, keep others out, clean with a suitable vacuum or wet method and prevent dust migration.

Hold or stop: Stop for failed extraction, dry sweeping, visible escape, unknown material, unprotected bystanders or RPE not fit for the wearer.

Completion and hand back: Clean and inspect the area, close defects, review monitoring and release access only after dust control is verified.

Evidence: Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back.

A refurbishment contractor needs to cut a series of concrete channels in a leisure-centre plant room. The job is indoors, noisy, near existing services and close to other trades. A generic RAMS says 'wear dust mask and use water where possible', but the work area has poor drainage and a standard vacuum is not suitable for fine construction dust.

A competent silica plan would first challenge whether chasing is needed at all. Could the route be surface-mounted, pre-formed or moved? If cutting remains necessary, the plan should specify tool, on-tool extraction or wet suppression, compatible electrical controls, segregation, suitable RPE, face fit where tight-fitting, clean-up method, waste route, supervision and a stop rule if visible dust escapes.

Decision pointWeak planStronger silica-control plan
DesignCut channels as shown.Check whether routing, pre-formed containment or alternative fixing avoids cutting. HSE
Tool selectionUse available grinder.Use a tool with effective on-tool extraction or wet system matched to the task. HSE
Dust extractionUse a workshop vacuum.Use suitable dust-class extraction, inspected and maintained for fine dust. HSE
RPEWear dust mask.Select suitable RPE for the assessed task; for high-dust silica construction, FFP3 is an example, with face fit and wearer checks. HSE HSE construction dust and RPE selection
SegregationTell other trades to keep clear.Set exclusion zone, sequence work and prevent bystander exposure. HSE
HousekeepingSweep up afterwards.Use suitable vacuum or damp cleaning; never dry sweep silica dust. HSE
EvidenceRAMS signed.Task-specific assessment, equipment checks, RPE fit, briefing and supervisor verification. HSE

When should silica work stop or escalate?

Stop or escalate where silica-containing work is uncontrolled, dusty, unplanned, poorly supervised or not matched to the assessment.

Relevant direct sources: HSE.

Silica stop triggers should be clear enough for a worker or supervisor to act immediately. If visible dust escapes, extraction fails, water supply is lost, tight-fitting RPE has not been face-fit tested, the work moves indoors or other trades are exposed, the job should pause until controls are restored or the method is redesigned.

Escalation is not failure. It is good management. High-dust work often needs better equipment, revised sequencing, occupational hygiene advice or client/design decisions that a worker cannot make alone.

TriggerWhy it mattersAction
Uncontrolled cutting or grinding starts without the specified effective dust-control systemHigh RCS generation likely.Stop and apply designed water/extraction controls or redesign. HSE
Visible dust escapes controlControls are not capturing the hazard.Pause, check tool, shroud, vacuum, water and work position. HSE
No suitable RPE, or missing face fit where RPE is tight-fittingResidual exposure may be uncontrolled.Do not proceed until suitable RPE controls are in place. HSE
Dry sweeping or compressed air cleaningSettled dust becomes airborne again.Use suitable vacuum or damp method. HSE
Nearby workers/public exposedBystander exposure is being ignored.Segregate, reschedule or enclose the task. HSE
Repeated dusty tasksCumulative exposure and surveillance duties may apply.Review COSHH, monitoring and health surveillance. HSE

Apply the learning

The fictional Eastbank cut moves indoors after an extractor repair and a change of material.

Decision and explanation

Reassess the whole task, verify the restored control system and protect everyone exposed before briefing a restart.

Several changes can alter exposure together. A repair alone does not validate the revised work arrangement.

Lesson 18

Turn learning into a workplace check

Course learning supports informed challenge. Actual exposure assessment, equipment selection and occupational health arrangements require competent site-specific decisions.

Use the full silica dust lesson

Follow the official sources below and retain the task-specific evidence. Official guidance: source Official guidance: HSE construction dust and RPE selection Task decision: Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back. Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction.

Apply it: Which official source and full-topic section will you use to resolve the next decision?

Visual practice · Turn learning into a workplace check

Actual SHAREsimulate construction model context: Dry cutting is proposed without its source control
Actual SHAREsimulate model capture · Dry cutting is proposed without its source control. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Use the full silica dust lesson

Follow the official sources below and retain the task-specific evidence. Official guidance: source Official guidance: HSE construction dust and RPE selection Task decision: Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back. Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction.

What should each role learn and demonstrate?

Competence requires a person to select and use the right control for a real dust or fume task, recognise failure and act before exposure continues. HSE supports the control principle. Assess a realistic task, record observation and reassess after material, equipment or health findings change.

How harm develops in the linked model

Respirable crystalline silica can cause silicosis, lung cancer and other serious disease. Harmful fine dust may remain when the visible cloud disappears.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What should each role learn and demonstrate?

Competence requires a person to select and use the right control for a real dust or fume task, recognise failure and act before exposure continues.

HSE supports the control principle. Assess a realistic task, record observation and reassess after material, equipment or health findings change.

RoleLearningDemonstrationAssessor recordReassess when
Cutter/operatorIdentify RCS tasks, material and control failure.Set tool extraction or water and stop when it fails.Observed task and control check.At tool/material/site change.
SupervisorProtect bystanders and verify the workface.Reject dry sweeping or unprotected dust escape.Workface observation and defect close-out.After change or near miss.
Equipment maintainerMaintain extraction, filters and water feed.Demonstrate capture and safe filter handling.Maintenance and test record.At service interval or defect.
Safety adviser/hygienistPlan exposure assessment and WEL interpretation.Explain eight-hour TWA and why below WEL is not enough.Sampling plan and control decision.At process or material change.
Occupational-health adviserApply risk-based surveillance confidentially.Explain trigger, referral and record boundary.Restricted health programme record.When risk or health findings change.

Apply the learning

Your action plan promises better masks but names no source-control check or owner.

Decision and explanation

Specify the task, source controls, responsible person, evidence and review trigger with competent support.

Course learning supports informed challenge. Actual exposure assessment, equipment selection and occupational health arrangements require competent site-specific decisions.