SHARE Knowledge Hub

Silica Dust

Silica dust is airborne dust containing respirable crystalline silica, usually produced when materials such as concrete, mortar, brick, stone, tiles, ceramics, engineered stone, rock or sandstone are cut, drilled, ground, polished, blasted or broken. The dangerous fraction is often invisible under normal lighting and can reach the deep lung. In Great Britain, HSE identifies a WEL for RCS of 0.1 mg/m3 as an 8-hour time-weighted average, but that limit is not a target to work up to. Good control means designing work to avoid dust, using lower-dust methods, water suppression or on-tool extraction, M-class or equivalent suitable vacuuming, suitable RPE such as face-fit-tested FFP3 where needed, health surveillance where required, and evidence that controls are used during real tasks.

Updated 2026-11-11UK focus

Understanding Silica Dust

Silica dust is airborne dust containing respirable crystalline silica, usually produced when materials such as concrete, mortar, brick, stone, tiles, ceramics, engineered stone, rock or sandstone are cut, drilled, ground, polished, blasted or broken. The dangerous fraction is often invisible under normal lighting and can reach the deep lung. In Great Britain, HSE identifies a WEL for RCS of 0.1 mg/m3 as an 8-hour time-weighted average, but that limit is not a target to work up to. Good control means designing work to avoid dust, using lower-dust methods, water suppression or on-tool extraction, M-class or equivalent suitable vacuuming, suitable RPE such as face-fit-tested FFP3 where needed, health surveillance where required, and evidence that controls are used during real tasks.

Why this matters at work

Obtain occupational-health advice on appropriate health surveillance and work restrictions under the assessed risks. Keep clinical results confidential and use functional recommendations to agree safe work. Established silicosis cannot be reversed, and disease can progress after exposure ends, so a normal day at work or absence of early symptoms is not reassurance that past or present exposure was harmless. Retain the exposure and control history and review the method after any clinical or monitoring concern.

The manager agrees provider competence, exposed groups, timing, prior work history, access, explanation of results and functional advice. Do not wait for a disease case or use a normal questionnaire as permission to keep ineffective controls. A current or past exposure history is part of clinical interpretation, not an admission that only this employer could have caused harm.

How organisations manage this in practice

A supervisor receiving a wrongly sized worktop should pause and compare controlled return to fabrication with the proposed site modification. Record the decision and actual controls, rather than authorising the cut because a customer is waiting. Keep RPE on for the planned dusty cleanup, remove waste without exposing others and verify the handover condition.

Encourage prompt healthcare assessment and provide a work history that describes materials, tasks, exposure duration and controls. Symptoms have several possible causes and a manager cannot diagnose silicosis. Severe new breathing difficulty requires urgent medical help. Review current exposure for the person and others immediately; do not wait for a diagnosis before correcting visibly failed controls.

Check that the specified suppression or extraction is operating as intended at the tool or release point and that the worker can use it throughout the task. Examine hoses, connections, water delivery, filters and the relevant indicators under the equipment instructions. A fan running somewhere in the room does not show source capture. Assess bystander exposure and any effect of working indoors or in a confined area. Where RPE is required, select protection appropriate to the assessed exposure and task, arrange face-fit testing for tight-fitting types and ensure an effective seal. Provide training, maintenance and storage, and stop work when necessary protection fails. Keep inspection and defect records appropriate to the system and meet its applicable examination requirements. Do not invent one service interval for every tool or respirator. Monitoring can help verify control but cannot repair missing safeguards.

Follow the control chain from the cut to clean-up

Respirable crystalline silica can be invisible. Match the control to the material and task, verify the source-control function and protect other people before relying on residual protection.

Dust-extracted masonry saw and vacuum at a UK site. Photorealistic illustration.
Illustrative UK workplace scene. Read the practical checks below for responsibilities, evidence and limits. Download image · Download smaller image
  1. Avoid or redesign

    Check whether the service route, material or off-site method can remove the dusty cut. Assess the replacement method’s risks rather than assuming it is automatically safer.

  2. Match the source control

    Use the assessed task-specific water suppression or extraction and compatible equipment. The sketch is not a prescription to combine methods that the actual equipment cannot support.

  3. Verify water or airflow

    Check the required supply, capture and maintenance evidence before and during the task. Stop on failed essential control; absence of visible dust does not prove control.

  4. Protect nearby people

    Manage the work zone, access, adjacent activities and cleaning. Consider others who do not operate the tool but may share the exposure route.

  5. Residual protection and clean-up

    Use suitable assessed RPE where required with applicable fit and care arrangements. Clean using the assessed dust-control method, avoiding dry sweeping and other dust-raising practices.

  6. Review evidence and health

    Keep useful task, material and control records and the applicable surveillance arrangements. The existing lung model illustrates anatomy; it does not measure exposure or diagnose silicosis.

Read the complete controls: ERICPD planning prompts

Discipline verifies and sustains all the controls; it is not a separate substitute for them.

Silica Dust — ERICPD planning prompts
Prompt or levelComplete task-specific example
EliminateAssess a surface service route that avoids cutting.
ReduceCheck all hazards of a proposed substitute material or method.
IsolateMatch suppression or extraction to the tool and separate bystanders.
ControlControl clean-up and provide the assessed equipment and method.
PPESelect suitable residual RPE.
DisciplineVerify water or airflow and stop when the planned control fails. Read the accompanying source table for the framework distinctions.
Read the complete controls: ESEAP effectiveness order

Compare stronger feasible controls while preserving the actual task, checks and release requirements.

Silica Dust — ESEAP effectiveness order
Prompt or levelComplete task-specific example
EliminationAssess a surface service route that avoids cutting.
SubstitutionCheck all hazards of a proposed substitute material or method.
Engineering controlsMatch suppression or extraction to the tool and separate bystanders.
Administrative controlsControl clean-up and provide the assessed equipment and method. Verify water or airflow and stop when the planned control fails.
PPESelect suitable residual RPE. Read the accompanying source table for the framework distinctions.

The particle inset is illustrative and supplies no measured concentration, exposure time, safe badge or interchangeable silica/asbestos mechanism.

Silica: stop fine dust travelling from the task to the lungs: illustrative 3D equipment and the people who may be affected
Interactive 3D explainerSHAREsim

Silica: stop fine dust travelling from the task to the lungs

Explore how this equipment can harm its users and other people, then follow the practical measures that interrupt each pathway. This is a hazards and good-practice lesson; the separate checklist remains the pre-use/safety-check activity.

Checksheets and risk assessments

Equipment checksheets

Risk assessment forms

Risk assessment examples

Forms and tools

Full written walkthrough — all 8 steps
  1. 1. Identify the material and complete task

    What is happening: The saw and drill are separate teaching examples, not a design for every stone product.

    How harm can occur: Cutting, drilling or disturbing residues can release invisible respirable particles that reach the deep lung.

    Best practice to apply: Identify the actual material, task and other exposed people; consider avoiding processing or using a safer product/method.

    Why this works: Bulk silica percentage and visible appearance do not establish breathing-zone exposure.

    Silica Dust · What is silica dust and why is it so harmful?
  2. 2. Choose source control for the process

    What is happening: The workpiece and tool define where dust is released and how it can be controlled.

    How harm can occur: An unsuitable control can leave a fine airborne fraction even when coarse dust is reduced.

    Best practice to apply: Plan suitable source controls and current task-specific guidance; engineered-stone controls need their own specific assessment.

    Why this works: Control selection must follow the material and process, rather than treating all dusty tasks as identical.

    Silica Dust · How can the hierarchy of controls reduce respirable crystalline silica exposure at source?
  3. 3. Follow water to the cutting point

    What is happening: In the wet-saw example water is directed towards the cutting interface.

    How harm can occur: A lost, unsuitable or ineffective supply can allow dust to escape while cutting continues.

    Best practice to apply: Use the specified functioning suppression and relevant mist/slurry controls; stop and resolve control failure.

    Why this works: Water present somewhere on site does not prove that it reaches and controls the point of release.

    Silica Dust · What does a controlled silica workflow look like?
  4. 4. Follow dust into on-tool extraction

    What is happening: The shrouded-drill example connects the tool's release point, hose and collector.

    How harm can occur: A poor shroud, leak, restriction or unsuitable collection arrangement can allow dust towards people.

    Best practice to apply: Match the complete on-tool system to the task and contaminant and verify its function; compare the separate example explicitly.

    Why this works: A connected collector alone does not prove capture at the tool.

    Silica Dust · How should a concrete cutting task be controlled?
  5. 5. Keep collector and residues controlled

    What is happening: The filter and collection container retain material that remains hazardous.

    How harm can occur: Opening, servicing or poorly sealed equipment can release concentrated residue to workers.

    Best practice to apply: Use suitable filter/collection equipment and the actual contained servicing, isolation and waste method.

    Why this works: Moving dust out of the cutting area does not remove its hazard during maintenance or disposal.

    Silica Dust · Where do silica dust controls commonly fail?
  6. 6. Prevent a second release during clean-up

    What is happening: Settled dust and slurry can become a later source when dried or disturbed.

    How harm can occur: Dry sweeping, compressed-air cleaning or uncontrolled residue handling can re-expose workers and others.

    Best practice to apply: Use suitable dust-controlled cleaning and contained waste/wet-residue arrangements; avoid creating another airborne release.

    Why this works: Clean-up belongs in the exposure plan, not after the control system has been removed.

    Silica Dust · What does a controlled silica workflow look like?
  7. 7. Provide suitable residual protection for the person

    What is happening: Respiratory protection must be selected and managed for the actual process and person.

    How harm can occur: Incorrect type, fit or use can leave inhalation risk; a generic mask is not a universal control.

    Best practice to apply: Follow the task-specific assessment and current guidance for suitable RPE and fit/use arrangements while retaining source controls.

    Why this works: RPE selection cannot be inferred from the unassigned teaching facepiece shown here.

    Silica Dust · How do WELs, monitoring and health surveillance fit together?
  8. 8. Verify performance and respond to change

    What is happening: Exposure assessment, symptoms and changes in material or work test whether the method remains suitable.

    How harm can occur: A visually tidy task can still create harmful exposure and long-latency disease.

    Best practice to apply: Use competent verification and required monitoring/surveillance, act on defects and symptoms and re-plan changed work.

    Why this works: Absence of visible dust or illness does not demonstrate adequate control.

    Silica Dust · How do WELs, monitoring and health surveillance fit together?

Illustrative awareness learning. Geometry, colours and movement do not establish safe distances, capacity, exposure, isolation or work permission. Use the actual assessment, equipment information and competent arrangements.

The wider workplace has its own account and subscription access. Exploring this lesson does not grant access, record course completion or authorise work.

UK guidance for further reading

HSE: Silica
SHAREsimulate

How can I practise this topic in 3D?

Dry cutting is proposed without its source control
3D workplace practiceSHAREsim

Dry cutting is proposed without its source control

All related inspection points 1 across 1 location
Construction site 1 inspection point

Practice in the SHAREhub environment. Browser practice is separate from workplace competence and formal learning records.

What is silica dust and why is it so harmful?

Respirable crystalline silica (RCS) is the fine airborne fraction released when silica-containing stone, concrete or similar material is worked. It can enter the deep lung and cause irreversible silicosis, COPD and lung cancer; dust may be invisible under normal lighting.

Direct authority grounds the mechanism; use the clinical route for an individual worker.

Silica is present in many common materials. It is not the presence of a block, slab or tile that creates the highest risk; it is the work that breaks the material into fine airborne particles. Cutting concrete kerbs, chasing brick walls, drilling overhead, grinding mortar, polishing engineered stone and dry sweeping settled construction dust can all produce dust that is too fine to see clearly but small enough to be breathed deeply into the lungs.

Silica dust should be treated as a serious health risk, not a cleanliness issue. HSE links RCS exposure with silicosis, COPD and lung cancer. Disease may develop slowly after years of exposure, while very high short-term exposure can cause faster and severe disease. Because harm may not be obvious on the day, controls need to be planned and verified rather than left to worker judgement at the point of dust generation.

A good silica control system starts before the tool is switched on. It asks whether cutting can be avoided, whether materials can be ordered to size, whether the work can be done wet, whether on-tool extraction is matched to the tool, whether nearby people are protected and whether the clean-up method prevents dust being put back into the air.

ConceptMeaningPractical consequence
SilicaMineral found in rocks, sand, clay and many construction materials.Material identification matters before work starts. HSE
Crystalline silicaForms such as quartz, cristobalite and tridymite.Quartz is common; heat and industrial processes can change forms. HSE
Respirable fractionDust small enough to penetrate deep into the lungs.Invisible or low-visibility dust can still be dangerous. HSE
RCS WELGB WEL for RCS is 0.1 mg/m3 as an 8-hour TWA.The WEL is a legal maximum after controls, not a design target. HSE
Cumulative doseRisk builds with concentration, duration and frequency.Short dusty jobs can add up across weeks and years. HSE
High-energy tasksCutting, grinding, drilling, blasting and breaking generate high dust quickly.Task method is often more important than job title. HSE
Control failureDust escapes because extraction, water, RPE, segregation or housekeeping fail.Supervisors need practical stop triggers. HSE

RPE is selected for the actual task and residual exposure. HSE identifies FFP3 as advisable for high-dust silica construction; a mask alone is not the control method. HSE construction dust and RPE selection.

How do the lungs work, and how can workplace exposures affect breathing?
Interactive 3D anatomySHAREsim

How do the lungs work, and how can workplace exposures affect breathing?

Interactive anatomy · Respiratory tract and lungs · Updated 2026-10-23

Read all anatomy and process explanations without the viewer

Simplified education, not diagnosis, a lung-function or oxygen-saturation test, an exposure calculator or a fitness-to-work assessment. No breath-holding challenge, breathing-rate score or personal health-data collection. Ordinary particle filters do not protect against every gas or oxygen deficiency. COPD and coal-dust topics may reuse normal anatomy only until separate mechanisms are reviewed.

Nose and mouth

Air enters and leaves here. The nose and mouth connect the outside air with the respiratory passages. Air moves through these openings on both the inward and outward breath. Follow the route towards the windpipe before looking at the smaller branches. The illustrated flow is air, a mixture of gases, rather than pure oxygen passing directly into blood. Frimley Health NHS Foundation Trust: How your lungs work · Central and North West London NHS Foundation Trust: How do we breathe?

Trachea

The windpipe carries air into the chest. The trachea, commonly called the windpipe, carries air down towards the chest. It divides into the two main bronchi that supply the lungs. Locate this shared passage before following either branch. Its role is to conduct air towards the gas-exchange regions and provide an outward route for the next exhalation. Frimley Health NHS Foundation Trust: How your lungs work

Bronchi

A main branch carries air into each lung. The two main bronchi take air from the windpipe into the right and left lungs. They divide into progressively smaller branches, distributing the breath through the lungs. Use the split as a landmark before following one highlighted route. These are air passages, distinct from the blood vessels that run through the same organs. Frimley Health NHS Foundation Trust: How your lungs work · University Hospitals of North Midlands NHS Trust: My lung surgery: about your lungs

Bronchioles

Smaller branches distribute air. Bronchioles are smaller branches of the airway system inside the lungs. Their branching routes lead towards clusters of alveoli, where the breath reaches the gas-exchange surface. Follow one branch to its end, using the others as context. This simplified route represents part of a much larger network supplying the lungs together. Frimley Health NHS Foundation Trust: How your lungs work

Alveoli

Tiny air sacs provide a gas-exchange surface. Alveoli are tiny air sacs at the ends of the small airway routes. Their close relationship with surrounding capillaries allows oxygen to pass towards blood and carbon dioxide towards alveolar air. Connect the highlighted cluster with the enlarged gas-exchange view. The enlargement changes the scale so the air space and neighbouring blood vessel can be distinguished. Frimley Health NHS Foundation Trust: How your lungs work · Central and North West London NHS Foundation Trust: How do we breathe?

Air–blood barrier

A thin boundary separates air from blood. The thin alveolar and capillary walls separate air in the sac from blood in its neighbouring vessel. Oxygen and carbon dioxide cross this boundary in opposite directions. Locate the tissue between the two spaces in the enlarged view. Blood cells remain in the vessel; the model does not represent an open connection through which air and blood mix. Central and North West London NHS Foundation Trust: How do we breathe?

Pulmonary capillaries

Small blood vessels pass beside the air sacs. Pulmonary capillaries are small blood vessels beside the alveoli. Blood moving through them receives oxygen and releases carbon dioxide across the thin exchange boundary, then continues through the circulation. Follow the labelled gas routes separately from the blood cells. These cells stay inside the capillary rather than moving into the air sac. Central and North West London NHS Foundation Trust: How do we breathe?

Diaphragm

This muscle helps make room for a breath. The diaphragm is a broad, dome-shaped breathing muscle beneath the lungs. It contracts and flattens downwards during inhalation, helping increase the space in the chest. During a quiet exhalation it relaxes towards its dome shape. Compare it with the rib cage: their changing positions help move air without the lung tissue acting as a contracting muscle. Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved

Rib cage and breathing muscles

Chest movement changes the space around the lungs. The rib cage protects the chest organs and moves with the breathing muscles. Expansion upwards and outwards helps increase chest space during inhalation; relaxation reduces that space during a quiet exhalation. Compare this movement with the diaphragm below the lungs. Together these structures provide the mechanics that allow air to move through the airways. Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved

Pleura

Two thin layers surround the lungs and line the chest. The pleura has two thin layers around the lungs and inside the chest wall. A small amount of fluid between them allows the surfaces to slide with less friction as breathing changes the chest space. Locate this outer covering separately from the internal air sacs; it is not the thin air–blood exchange boundary. Blackpool Teaching Hospitals NHS Foundation Trust: Pleural clinic

Open the complete process transcript

The process, step by step

1 · Make space

Breathing in begins with a change in the space inside the chest. The diaphragm, a dome-shaped muscle beneath the lungs, contracts and moves downwards. Muscles around the ribs help lift the chest upwards and outwards. As the lungs expand with this changing space, air can enter through the airways. Locate the diaphragm and rib cage together rather than treating the lungs as muscles that pull themselves open. The model separates the movement into a teaching step so you can follow its purpose. In the body, chest movement, airflow and blood circulation are connected parts of a continuing process. Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved

What to watch: Locate the diaphragm beneath the lungs and the rib cage around them; compare their positions with the space occupied by the lungs.

Why it matters: Changing the chest space draws air into the lung passages. The breathing muscles supply the movement, while the lungs expand with the chest to receive the next breath.

Explore this step: Select the diaphragm and rib cage in turn, then explain how their movement helps air enter without the lungs contracting like muscles.

2 · Move air

Air entering through the nose or mouth travels down the trachea, or windpipe, towards the chest. The trachea divides into the two main bronchi, with one route supplying each lung. Follow this continuous passage in the whole-chest view before moving into the smaller branches. The moving air is a mixture of gases, including oxygen; it is not a stream of pure oxygen travelling straight into the blood. These larger airways carry the breath towards the places where gas exchange happens. The same connected passages also provide the outward route when air is breathed out. Frimley Health NHS Foundation Trust: How your lungs work

What to watch: Start at the nose and mouth, follow the trachea downwards and find the split into the right and left main bronchi.

Why it matters: The larger passages distribute air to both lungs and connect the outside air with the smaller branches inside. Gas exchange takes place further along the route, rather than within the windpipe.

Explore this step: Trace the route to each lung and distinguish the tubes carrying air from the separate vessels carrying blood.

3 · Reach the air sacs

Inside each lung, the bronchi divide into smaller branches called bronchioles. These passages distribute air towards clusters of tiny air sacs, the alveoli. Follow one branch in the close-up and connect its end with an air-sac cluster, using the other branches as surrounding context. These routes distribute the breath throughout the lungs rather than supplying only one working air sac. A real lung contains many branching routes and air sacs operating together. This distribution brings air close to a large network of small blood vessels, preparing for the exchange shown in the next view. Frimley Health NHS Foundation Trust: How your lungs work

What to watch: Follow one smaller airway to the cluster of air sacs at its end, keeping the other branches as surrounding context.

Why it matters: Branching delivers air throughout the lungs instead of to one large chamber. The many air sacs bring the inhaled gases close to blood vessels where oxygen and carbon dioxide can cross.

Explore this step: Trace one complete branch to its air sacs, then explain how the many branches distribute air throughout the lungs.

4 · Change scale

The lesson now changes from a branching airway to an enlarged air–blood interface. An alveolus contains air; beside it runs a capillary containing blood. Their very thin walls form the boundary across which gases can move. Locate the air space, the separating tissue and the inside of the vessel before following any gas symbols. The magnified view represents a tiny part of the same lung, not a separate organ or a hole that joins air and blood into one space. The enlargement helps explain how the two systems can exchange gases while keeping their contents separate. Central and North West London NHS Foundation Trust: How do we breathe?

What to watch: Find the air inside the enlarged alveolus, the thin separating boundary and the neighbouring capillary with blood cells inside it.

Why it matters: A close boundary allows gases to cross between alveolar air and capillary blood. Keeping the two spaces separate lets ventilation and circulation cooperate without blood cells entering the air sac.

Explore this step: Identify the air space and blood-vessel space, then point to the boundary each gas must cross between them.

5 · Exchange gases

At the air–blood boundary, oxygen moves from the alveolar air into the capillary blood. At the same time, carbon dioxide carried back from the body moves from the blood into the air sac. The two gases cross in opposite directions; blood cells stay within the vessel. Follow each labelled symbol separately so that exchanging gases is not confused with mixing the air and blood together. Blood then carries oxygen onwards towards the heart and the body’s tissues. The teaching symbols simplify continuous gas movement, and their size, colour and speed do not represent a measurement. Central and North West London NHS Foundation Trust: How do we breathe?

What to watch: Follow the O₂ symbol towards the capillary and the CO₂ symbol towards the air sac, while locating the blood cells within the vessel.

Why it matters: Oxygen can be carried onwards for use by the body, while carbon dioxide returns to the airways for removal. Both transfers connect the breath with the continuing circulation of blood.

Explore this step: Trace the two gas routes in opposite directions and explain why a blood cell should remain inside the capillary.

6 · Breathe out

During a quiet breath out, the diaphragm and other breathing muscles relax. The diaphragm returns towards its dome shape, chest space decreases and air moves back along the airways to the nose or mouth. This outgoing air carries carbon dioxide that crossed from the blood into the alveoli. Trace the route in reverse without reversing the direction of blood circulation: oxygen-carrying blood continues towards the heart while another breath prepares to enter. The model presents a single cycle to explain the relationship. It does not show breathing as a series of separate events in which circulation stops between steps. Central and North West London NHS Foundation Trust: How do we breathe? · Cambridge University Hospitals NHS Foundation Trust: Breathing techniques to ease breathlessness: muscles involved

What to watch: Compare the diaphragm and chest with the inhalation step, then follow the outward airway route from the lungs to the nose or mouth.

Why it matters: Exhalation removes air containing carbon dioxide from gas exchange. Meanwhile, blood circulation continues carrying oxygen onwards, linking this breathing cycle with the needs of the rest of the body.

Explore this step: Trace the outward air route and the onward blood route separately, then describe why they are connected processes with different pathways.

Mechanisms and their limits

Dust-related fibrosis · silica Fine respirable crystalline silica can reach deep into the lungs, causing inflammation and areas of scarring. Scarred tissue does not work normally. Established silicosis damage cannot be reversed and may progress after exposure ends. Disease often develops over years, but very heavy exposure can cause much faster disease. No animation time represents a number of shifts or a safe dose. Show selected scarred regions, not every air sac filling with sand. This example does not diagnose the cause of breathlessness or show every effect of silica. NHS: Silicosis

Plan and control silica-generating cutting

Understand silicosis and seek assessment

Dust-related fibrosis · silica — follow the anatomy

Look at: The thin walls of the air sacs and their nearby blood vessels.

What changes: Respirable silica can reach deep into the lung and cause scarring over time.

Why it matters: Scarred tissue makes gas exchange harder; established silicosis cannot be reversed by simply stopping exposure.

What to do: Prevent dust at source using suitable wet methods or extraction and correctly selected respiratory protection.

Repeated uncontrolled cutting of paving materials

A paving crew uses a cut-off saw on kerbs without effective dust suppression. Explicit time jump: silicosis usually develops after prolonged exposure, sometimes faster after very heavy exposure. Scarring does not appear during the 32-second clip. The dust route and later fibrosis are explanatory stages. No single cut, visible cloud or symptom predicts an individual’s disease.

A silica-generating activity Cutting paving blocks or kerbs can create very fine silica-containing dust near the operator and nearby workers. Plan cuts and material choices before work starts. HSE: Construction dust: cutting paving blocks, kerbs and flags · NHS: Silicosis

Fine dust reaches deeper lung regions Some inhaled fine particles reach the alveolar region. Repeated uncontrolled exposure across separate tasks and days is represented by a clearly labelled time jump. NHS: Silicosis

Later inflammation and fibrosis The chosen long-term example marks inflammation and scarred lung tissue that cannot function normally. This is not a real-time scan, exposure calculator or inevitable outcome after one task. NHS: Silicosis

Control dust at the task Reduce cutting where possible, use suitable water suppression or on-tool extraction with the required RPE, and check controls. Report symptoms and exposure history to a healthcare professional; controls do not erase existing scarring. HSE: Construction dust: cutting paving blocks, kerbs and flags · NHS: Silicosis

Read the practice situations and all answer explanations
LU-Q1: Which plan best addresses the hazard?

A team plans repeated concrete cuts with a handheld cut-off saw. Dust can enter the operator’s and nearby workers’ breathing zones.

Open a window and use the same dry-cutting method. — A window alone does not control dust generated beside the face. Choose task controls that prevent or capture it at source.

First reduce the need to cut, then assess source suppression or extraction and any required suitable RPE. — This addresses the task before exposure occurs. Check that suppression or extraction works and that required RPE is suitable, fitted and used.

Continue while nobody is coughing. — Symptoms are not an exposure monitor. Harmful respirable dust may be invisible, and a worker can feel well during exposure.

HSE: Construction dust: cutting paving blocks, kerbs and flags
LU-Q2: What is the most useful next action?

A bakery worker notices repeated wheeze after dusty flour tasks, including some symptoms later in the evening.

Report the pattern and seek medical and workplace assessment. — Reporting the pattern allows exposure controls and clinical assessment to be reviewed. Symptoms can be delayed; a clinician may need further investigation.

Use this model to diagnose occupational asthma. — The model explains a mechanism. It cannot diagnose asthma or establish that work caused it.

Assume the task is safe if breathing improves away from work. — Improvement away from work may be useful information for investigation, but it does not show that returning to the same exposure is safe.

HSE: Asthma: an overview · HSE: Advice for employers: occupational asthma · NHS: Asthma · HSE: Flour dust and risks to bakers
LU-Q3: What is the important distinction?

One diagram shows a narrowed airway at LUN03–04. A second shows scarred gas-exchange tissue around LUN05–07.

They show the same disease at successive stages. — Narrowed airways and scarred lung tissue are different changes. One is not automatically the next stage of the other.

Both effects disappear when airborne dust settles. — Removing airborne dust does not reverse established fibrosis. Controlling further exposure remains important.

Airway narrowing and tissue fibrosis are different mechanisms. — Correct. Airway narrowing affects the passage for air; fibrosis affects lung tissue and its function. Neither picture supplies an individual diagnosis.

NHS: Silicosis · NHS: Asthma
Sources and how the model is made

The opening images are AI-generated anatomical illustrations. The interactive 3D models and labelled SVG diagrams use original procedural artwork. These teaching images are not medical scans or diagnostic tools. Source references support the learner explanations and do not grant artwork rights.

· Three.js MIT licence

How should silica dust risk be assessed?

Assess the material, task energy, duration, enclosure, people exposed, controls and evidence before work starts.

Relevant direct sources: HSE.

A silica assessment should be task-specific enough to change the work. 'Cutting concrete' is not enough. The assessor needs to know how much cutting, which tool, whether it is indoors or outside, whether water or extraction is fitted, whether the extraction unit is suitable, who stands nearby, how dust is cleaned up and whether any tight-fitting RPE has been face-fit tested for that wearer, while all selected RPE meets the task’s protection, compatibility and use requirements.

The strongest assessments look at both planned and foreseeable poor conditions. What if water cannot be used because of electrics? What if the vacuum filter blocks? What if a subcontractor brings a dry-cutting tool? What if the task moves indoors? What if a worker has stubble that breaks the mask seal? These practical questions turn silica assessment into risk control.

Assessment factorWhat to askWhy it matters
MaterialDoes the material contain silica and how much is likely?Sandstone, concrete, brick, mortar, granite and engineered stone create different exposures. HSE
TaskIs work cutting, drilling, grinding, polishing, blasting, breaking or sweeping?High-energy tasks generate respirable dust quickly. HSE
MethodCan cutting be avoided, reduced, wet-controlled or extracted?Design and method changes are stronger than PPE. HSE
EnvironmentIs work indoors, enclosed, windy, overhead or near other trades?Dust build-up and spread can change exposure dramatically. HSE
Duration/frequencyHow long and how often will the task occur?Dose accumulates even where each task looks short. HSE
People exposedWho is doing the task and who is nearby?Bystanders, labourers and cleaners can be exposed. HSE
Control evidenceWhat proves water, extraction, RPE and cleaning will work?Controls must be verified before and during work. HSE

How should a concrete cutting task be controlled?

A worked task example shows how silica dust control should be planned, checked and evidenced at the workface.

Control RCS exposure while cutting a concrete service chase

Task material and setting: A contractor cuts a service chase into a concrete wall in an occupied refurbishment site; cutting can release invisible RCS into the room.

People and prerequisites: The site manager owns the work; the cutter checks material, other occupants, tool and extraction compatibility; a competent adviser plans exposure verification where needed.

Before: Consider a surface route or off-site prefabrication. If cutting remains necessary, fit effective on-tool extraction with an appropriate M/H-class unit or suitable water suppression, segregate the area and select residual RPE.

During: Check extraction flow and capture, position the tool, keep others out, clean with a suitable vacuum or wet method and prevent dust migration.

Hold or stop: Stop for failed extraction, dry sweeping, visible escape, unknown material, unprotected bystanders or RPE not fit for the wearer.

Completion and hand back: Clean and inspect the area, close defects, review monitoring and release access only after dust control is verified.

Evidence: Keep material identification, COSHH assessment, control selection, tool and filter checks, RPE fit, exposure assessment, worker briefing and hand-back.

A refurbishment contractor needs to cut a series of concrete channels in a leisure-centre plant room. The job is indoors, noisy, near existing services and close to other trades. A generic RAMS says 'wear dust mask and use water where possible', but the work area has poor drainage and a standard vacuum is not suitable for fine construction dust.

A competent silica plan would first challenge whether chasing is needed at all. Could the route be surface-mounted, pre-formed or moved? If cutting remains necessary, the plan should specify tool, on-tool extraction or wet suppression, compatible electrical controls, segregation, suitable RPE, face fit where tight-fitting, clean-up method, waste route, supervision and a stop rule if visible dust escapes.

Decision pointWeak planStronger silica-control plan
DesignCut channels as shown.Check whether routing, pre-formed containment or alternative fixing avoids cutting. HSE
Tool selectionUse available grinder.Use a tool with effective on-tool extraction or wet system matched to the task. HSE
Dust extractionUse a workshop vacuum.Use suitable dust-class extraction, inspected and maintained for fine dust. HSE
RPEWear dust mask.Select suitable RPE for the assessed task; for high-dust silica construction, FFP3 is an example, with face fit and wearer checks. HSE HSE construction dust and RPE selection
SegregationTell other trades to keep clear.Set exclusion zone, sequence work and prevent bystander exposure. HSE
HousekeepingSweep up afterwards.Use suitable vacuum or damp cleaning; never dry sweep silica dust. HSE
EvidenceRAMS signed.Task-specific assessment, equipment checks, RPE fit, briefing and supervisor verification. HSE

Which materials and tasks create silica dust?

Silica risk depends on both the material and the energy of the work activity.

Relevant direct sources: HSE.

Some materials contain more silica than others, but a lower-silica material can still create harmful exposure if the task is dusty, prolonged or enclosed. The assessor should never rely on material name alone.

The practical rule is to treat powered cutting, grinding, drilling, scabbling, polishing, blasting, breaking and dry sweeping as exposure-generating tasks until suitable control is proven.

Material or workTypical taskRisk point
Sandstone, gritstone and quartziteCutting, carving or grinding.Often high silica content and high RCS potential. HSE
Concrete and mortarCutting, chasing, coring or breaking.Common construction source of RCS. HSE
Brick and blockSaw cutting, drilling and chasing.Repeated short cuts can create cumulative exposure. HSE
Granite and engineered stonePolishing, cutting and edge finishing.Workshop exposure can be intense and repeated. HSE
Foundry sand or mouldsShakeout, fettling and cleaning.Mixed metal and silica dust exposure. HSE
Settled construction dustDry sweeping or compressed air cleaning.Re-suspends fine dust into the breathing zone. HSE

What does a controlled silica workflow look like?

A controlled workflow prevents dust generation where possible, captures remaining dust and prevents secondary exposure during clean-up.

Relevant direct sources: HSE, HSE.

Silica control is often lost in the sequence, not the theory. Work is planned too late, the right tool is unavailable, the vacuum does not fit the shroud, the water supply is awkward, the exclusion zone is not set and cleaning is rushed.

A good workflow is visible and repeatable. It tells the supervisor what must be ready before work starts, what must be checked during the task and what evidence confirms the area was left clean without exposing other people.

StageControl standardEvidence
PlanAvoid or reduce cutting; choose pre-sized materials or alternative methods where practicable.Design review, procurement note or method decision. HSE
PrepareSelect controlled tool, extraction/water, power arrangements, RPE and exclusion zone.Pre-start checklist and equipment check. HSE
BriefExplain dust health risk, control method, nearby-person protection and stop triggers.Toolbox talk or task briefing. HSE
Stop visible dustPause if dust escapes the shroud, water, extraction or exclusion zone.Stop-work record, defect report or changed method. HSE
Control during workUse water/extraction correctly; keep shrouds, filters and airflow effective.Supervisor observation and defect response. HSE
Protect peopleSegregate, schedule and prevent bystander exposure.Barrier/signage and work sequencing record. HSE
CleanUse suitable vacuum or damp method; prevent dry sweeping.Housekeeping inspection and waste route. HSE
Monitor and surveilUse exposure monitoring and health surveillance where risk and regular exposure require it.Monitoring report, OH programme and competent interpretation. HSE
ReviewRecord defects, visible dust, exposure concerns and worker feedback.Action tracker and assessment update. HSE

Check suitability of all selected RPE and face-fit testing where tight-fitting. A suitable loose-fitting powered alternative is not excluded solely because it does not require a face-seal fit test.

Pre-start evidence should identify the compatible tool, shroud, hose and extractor, the manufacturer’s flow indication/check, filter/container condition, safe emptying method and restart authority. For a wet method, verify sustained water delivery and slurry control. The vacuum class alone does not demonstrate capture at the tool; clean-up attachments and on-tool capture have distinct tasks. Stop for failed extraction, loss of required water or dust escape.

How do WELs, monitoring and health surveillance fit together?

The WEL helps define legal exposure control, while monitoring and surveillance test whether controls are adequate and health is being protected.

Relevant direct sources: HSE, HSE.

HSE states the WEL for RCS is 0.1 mg/m3 as an 8-hour TWA. That number should not be used as permission to create dusty work. COSHH requires exposure to be prevented or adequately controlled, and for carcinogens and asthmagens exposure must be controlled to as low as reasonably practicable.

Air monitoring is useful where exposure is uncertain, control effectiveness needs proof or high-risk work is repeated. Health surveillance is required where workers are regularly exposed to RCS and there is a reasonable likelihood that silicosis may develop. Both need competent interpretation and should drive control improvement.

ElementWhat it doesWhat it does not do
WELSets a legal airborne exposure limit over a reference period.Does not prove work is well controlled if exposure is just below the limit. HSE
Exposure monitoringMeasures representative breathing-zone exposure during tasks.Does not replace engineering control or supervision.
Health surveillanceLooks for early signs of work-related ill health where legally/clinically appropriate.Does not make exposure acceptable.
RPE face fitChecks tight-fitting mask seal for the wearer.Does not compensate for cutting without the specified effective dust controls or poor extraction.
LEV/TExTChecks extraction remains effective over time.Does not prove users position the hood correctly every time.

EH40 identifies the substance limit and averaging period. The surveillance guide supports the RCS health-surveillance trigger; INDG463 supports source control and suitable RPE. The table’s monitoring, fit and extraction checks are complementary controls, not separate requirements established by EH40 alone. Select and verify the actual equipment and programme with competent advice. HSE RCS surveillance trigger; HSE silica control and worker protection.

What do people commonly get wrong about silica dust?

Common misunderstandings usually underestimate invisible dust, short tasks, clean-up exposure and RPE limitations.

Relevant direct sources: HSE.

Silica dust is dangerous partly because it does not look dramatic. A small haze, dusty clothing or powder on a sill can be treated as mess rather than evidence of airborne exposure. Workers may also believe outdoor work is automatically safe, or that a mask alone is enough.

The best training uses specific mistakes. It shows why dry sweeping is stopped, why vacuum class matters, why stubble can defeat a tight-fitting mask and why other trades must be protected.

MisunderstandingRealityTeaching point
Only visible clouds matter.RCS may be too fine to see under normal light.Control the task, not just visible dust. HSE
A short cut is low risk.Repeated short cuts create cumulative dose.Plan all high-energy silica tasks. HSE
Outdoor work is safe.Wind direction and breathing-zone exposure still matter.Use controls outdoors too. HSE
Any vacuum will do.Fine dust can pass through unsuitable equipment.Use suitable dust-class extraction and maintain it. HSE
FFP3 solves the problem.RPE depends on fit, wear time, compatibility and user behaviour.Use RPE as part of a control package. HSE HSE construction dust and RPE selection
Cleaning happens after exposure ends.Dry sweeping can be a high-exposure task.Control clean-up as part of the job. HSE

How does silica dust control differ by sector?

The same health risk appears in different forms across construction, stonework, foundry, quarry, utilities and maintenance work.

Relevant direct sources: HSE.

The control principle is common, but the operational detail changes. A stone workshop needs fixed extraction, segregation and cleaning regimes. A construction site needs sequencing, controlled tools and supervisor checks. A utility team needs mobile controls that work at the excavation or roadside.

This is why a single generic dust assessment is weak. The control standard must fit the sector, task, environment and people exposed.

SectorTypical silica activityControl focus
Construction refurbishmentChasing walls, cutting block, drilling concrete.Avoid cutting, on-tool extraction/water, task-selected RPE (for example FFP3 for high-dust silica work), segregation and clean-up. HSE HSE construction dust and RPE selection
StonemasonryCutting and polishing stone or engineered stone.Wet methods, extraction, enclosure, RPE and health surveillance. HSE
UtilitiesRoad saws, duct cutting and excavation dust.Water suppression, traffic interface, public protection and mobile welfare. HSE
FoundrySand mould handling, shakeout and fettling.Enclosure, LEV, RPE and mixed-dust monitoring. HSE
QuarryingDrilling, crushing and processing stone.Cab filtration, suppression, maintenance and exposure monitoring. HSE
Facilities maintenanceSmall drilling and fixing jobs in older premises.Pre-planning, controlled drilling and vacuum attachment. HSE

A refurbishment team needs portable tool controls, exclusion and a checked hand-back; a production workshop instead needs repeatable source capture, planned cleaning and maintenance across many tasks. In both illustrations the manager tests control effectiveness during real work and reviews exposure evidence after material, tool or layout changes. The same mask or vacuum cannot be selected solely from the word silica. HSE silica task-control context.

How can the hierarchy of controls reduce respirable crystalline silica exposure at source?

Remove or reduce the hazard before relying on procedures or personal protection.

For silica dust, assess the actual task and first look for a way to remove the hazard. Where that is not possible, consider a safer substitute, engineered separation and then clear work procedures. PPE protects against remaining exposure; it does not make an uncontrolled task safe. HSE hierarchy of controls

The selected measures need a named owner, a usable stop point and a check that they still work when the task or conditions change. In Northern Ireland, verify the separate legal route and site instructions.

For the service chase, first test a surface route that avoids cutting. If a substitute material or method is proposed, check all hazards rather than assuming lower silica means safe dust. Where cutting remains necessary, match suppression or extraction to the tool, prevent bystander exposure, control clean-up and select suitable residual RPE. The site manager provides the method and equipment; the supervisor verifies water or airflow and stops when the planned control fails. ERICPD (Eliminate, Reduce, Isolate, Control, PPE, Discipline) is a teaching prompt here; Discipline means keeping controls effective through checking and learning. HSE topic-specific control sequence.

When should silica work stop or escalate?

Stop or escalate where silica-containing work is uncontrolled, dusty, unplanned, poorly supervised or not matched to the assessment.

Relevant direct sources: HSE.

Silica stop triggers should be clear enough for a worker or supervisor to act immediately. If visible dust escapes, extraction fails, water supply is lost, tight-fitting RPE has not been face-fit tested, the work moves indoors or other trades are exposed, the job should pause until controls are restored or the method is redesigned.

Escalation is not failure. It is good management. High-dust work often needs better equipment, revised sequencing, occupational hygiene advice or client/design decisions that a worker cannot make alone.

TriggerWhy it mattersAction
Uncontrolled cutting or grinding starts without the specified effective dust-control systemHigh RCS generation likely.Stop and apply designed water/extraction controls or redesign. HSE
Visible dust escapes controlControls are not capturing the hazard.Pause, check tool, shroud, vacuum, water and work position. HSE
No suitable RPE, or missing face fit where RPE is tight-fittingResidual exposure may be uncontrolled.Do not proceed until suitable RPE controls are in place. HSE
Dry sweeping or compressed air cleaningSettled dust becomes airborne again.Use suitable vacuum or damp method. HSE
Nearby workers/public exposedBystander exposure is being ignored.Segregate, reschedule or enclose the task. HSE
Repeated dusty tasksCumulative exposure and surveillance duties may apply.Review COSHH, monitoring and health surveillance. HSE

Where do silica dust controls commonly fail?

Silica control usually fails through poor planning, unsuitable tools, weak RPE control, dry cleaning or failure to protect nearby people.

Relevant direct sources: HSE, HSE.

The common failure pattern is familiar: the assessment says water suppression or extraction will be used, but the tool arrives without a compatible shroud, the vacuum is not suitable, the water supply is impractical, or the supervisor only checks the paperwork.

A strong system checks the physical task. It tests whether the control is in place, usable and effective under the conditions of that job.

Failure or weak practiceHow it developsWhat good looks like
Generic RAMSSame dust controls copied across all tasks.Task-specific method, tool and environment review. HSE
Wrong extractionDomestic or unsuitable vacuum used.Suitable dust-class extraction matched to tool. HSE
Water not practicalWater method written but unavailable or creates other risk.Alternative controlled method planned. HSE
Mask not fit testedFFP3 issued with no fit test or clean-shaven rule.Face fit, user checks and alternative RPE where needed. HSE HSE construction dust and RPE selection
Dusty clothing/welfareContamination carried into vans or welfare.Decontamination, cleaning and changing controls. HSE
Bystanders ignoredOther trades work in the dust zone.Segregation and sequencing. HSE
No surveillance reviewHigh-risk repeated exposure continues without OH process.Health surveillance considered and arranged where required. HSE

What evidence shows silica dust is being controlled?

Evidence should prove that high-dust tasks are designed, controlled, briefed, inspected, cleaned and reviewed.

Relevant direct sources: UK legislation, HSE.

The evidence pack should show control in the real task, not just a signed method statement. It should include the task-specific assessment, equipment checks, RPE fit records, supervisor observations, cleaning records, exposure monitoring where needed and health surveillance arrangements.

Where silica exposure is a significant organisational risk, leaders should see leading indicators: uncontrolled dust events, extraction defects, face-fit compliance, worker concerns, monitoring results and overdue actions.

Evidence itemWhat it should showAssurance question
Risk assessment or technical assessmentScope, task, people exposed, route of exposure, existing controls, further controls, owner and review trigger.Does it match the real work, location, materials, people and abnormal conditions? UK legislation
Action trackerAction, owner, priority, due date, interim control and close-out evidence.Are serious-risk actions verified at the workplace before closure? UK legislation
Training and briefing recordsWho was trained, what they were trained on, how competence was checked and when refresh is due.Can people explain the health risk, controls and stop triggers? UK legislation
Inspection and maintenance recordsChecks on LEV, extraction, RPE, guards, welfare, permits, isolation or other critical controls.Are defects corrected before exposure or interface risk continues? UK legislation
Monitoring and surveillance recordsExposure monitoring, health surveillance status, anonymised trends and competent interpretation where relevant.Are results linked back to control review and work design? UK legislation
Incident, near-miss and concern recordsReported symptoms, dust clouds, exposure events, permit clashes, dermatitis signs or weak signals.Are early warnings investigated before harm becomes irreversible? UK legislation
Management reviewTrends, resources, assurance confidence, overdue actions and decisions.Are leaders reviewing control effectiveness rather than activity counts alone? UK legislation
Tool and extraction registerControlled tools, shrouds, vacuums, filters and maintenance.Are tools matched to the task and inspected? UK legislation
RPE fit-test registerWho is face-fit tested for which mask and when review is needed.Is the issued mask the same model as the fit test? UK legislation
Silica task inventoryTasks, materials, frequency, controls and surveillance triggers.Are repeated short tasks captured? UK legislation
Exposure monitoringRepresentative sampling and competent interpretation where needed.Do results lead to control improvements? UK legislation

How should silica dust controls be assured?

Assurance should focus on live work: dust generation, control use, RPE, housekeeping and worker understanding.

Relevant direct sources: HSE.

A good silica assurance check starts at the workface. The reviewer should watch how the tool is used, whether dust escapes, how RPE is worn, whether other people are exposed and how dust is cleaned afterwards.

Second-line reviews should test whether the organisation understands its silica risk profile, not just whether individual RAMS exist. Third-line or specialist support may be needed for repeated high-risk work, exposure monitoring strategy or health surveillance governance.

Assurance layerWhat to checkExample question
First lineTool, extraction, water, RPE and exclusion before and during work.Would this task create visible or invisible dust outside control? HSE
Second lineAssessment quality, equipment availability, face fit and action closure.Are high-dust tasks sampled against real work? HSE
Third lineOccupational hygiene strategy, surveillance and governance.Do monitoring and surveillance results change the control plan? HSE
Worker voicePractical barriers and symptom reporting.Can workers stop dusty work without pressure? HSE
Leadership reviewTrends, resourcing and repeated failures.Are dust controls funded and available before work starts? HSE

How should management check this work?

Use a defined plan, carry out the controls, check performance and correct what does not work.

For silica dust, assign a competent owner to set the work controls, check their use and review them after change, failure or new evidence. HSE managing health and safety

A management-system label or certificate is not approval of a site limit, procedure or individual work decision. Apply GB and NI duties to the correct location.

What should each role learn and demonstrate?

Competence requires a person to select and use the right control for a real dust or fume task, recognise failure and act before exposure continues.

HSE supports the control principle. Assess a realistic task, record observation and reassess after material, equipment or health findings change.

RoleLearningDemonstrationAssessor recordReassess when
Cutter/operatorIdentify RCS tasks, material and control failure.Set tool extraction or water and stop when it fails.Observed task and control check.At tool/material/site change.
SupervisorProtect bystanders and verify the workface.Reject dry sweeping or unprotected dust escape.Workface observation and defect close-out.After change or near miss.
Equipment maintainerMaintain extraction, filters and water feed.Demonstrate capture and safe filter handling.Maintenance and test record.At service interval or defect.
Safety adviser/hygienistPlan exposure assessment and WEL interpretation.Explain eight-hour TWA and why below WEL is not enough.Sampling plan and control decision.At process or material change.
Occupational-health adviserApply risk-based surveillance confidentially.Explain trigger, referral and record boundary.Restricted health programme record.When risk or health findings change.

What do the acronyms and key terms mean?

These terms separate the disease, hazardous exposure and control decision.

TermMeaningPlain-English use
RCSRespirable crystalline silicaFine silica-containing dust able to reach the deep lung.
COSHHControl of Substances Hazardous to HealthSeparate GB and NI hazardous-substance regulations.
WELWorkplace exposure limitSpecified airborne limit with an averaging period, not a safe target.
TWATime-weighted averageExposure averaged over the stated eight-hour reference period.
LEVLocal exhaust ventilationCaptures dust close to the cutting or grinding source.
RPERespiratory protective equipmentResidual protection after stronger source controls.
ERICPDEliminate, Reduce, Isolate, Control, PPE, DisciplineTeaching prompt; Discipline means supervision, maintenance and learning, not blaming a worker.