Body repair: dust, welding, grinding and LEV

Free online training · Approximate learning time: 110–175 minutes · Self-paced

Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.

110–175 minutes · Includes activities, model practice and assessment.

Independent awareness and decision learning for vehicle repair. Practical competence, EV high-voltage work, asbestos work and other specialist tasks require separate training and authorisation. GB baseline; check corresponding Northern Ireland duties and local arrangements.

Understand this repair environment

Control the entire exposure and fire pathway, from the repair surface to safe discharge.

Follow the work, not just the equipment

Accident repair changes the surface and structure of a vehicle. Sanding releases particles from fillers and coatings; grinding creates fragments and sparks; welding produces hazardous fume and radiation. Nearby preparation, mixing, vehicle fuel and waste can change the same job into a fire or exposure event. Assess the material and process together, including what is hidden behind the panel.

Start by asking whether the operation can be avoided or changed to reduce the release. Where extraction is required, place capture to control the contaminant at source and verify the real working arrangement. A hood behind the worker may draw fume through the breathing zone. General airflow and an open door do not establish effective capture. Selection of any additional respiratory protection must suit the hazard, wearer and task; its presence does not excuse failed engineering control.

Follow the extracted air beyond the hood. Ducts, joints, air-cleaning equipment, fan, airflow indication and discharge all contribute to the system. Capturing fume inside while discharging it onto a public footpath transfers the exposure. The job is ready only when the whole control route and the neighbouring work are suitable and functioning.

Fictional applied case

A welder positions the extraction hood on the far side of their head. A grinder guard has been removed for access, solvent-soaked waste sits behind the panel and the extractor outlet faces a pedestrian path. The fan sounds normal and the repair is almost finished.

Open the interactive lesson and check →

Choose controls that fit the actual task

Use source guidance to distinguish control selection, work instructions and evidence of effectiveness.

How should dust risk be assessed?

Dust risk should be assessed by material, task, exposure route, particle size, control effectiveness and worker health risk.

A suitable COSHH assessment names the substance and task. It should not simply state 'dust present'. It should identify whether the dust contains silica, wood, flour, cement, metals, biological material, toxic additives or combustible material, and separately identify suspected asbestos or lead for their own legal routes.

The assessment should describe who is exposed, how close they are to the source, how long the task lasts, whether the task is indoors or outdoors, what extraction is used, whether water suppression is effective, how cleaning is done and whether other workers nearby are exposed.

If there is uncertainty, exposure monitoring or specialist occupational hygiene advice may be needed. Monitoring should answer a management question: are controls adequate, which task is worst, who is exposed, is the WEL exceeded, or does a control improvement work? See HSE - COSHH.

Dust assessment questions - Dust assessment questions
Question Why it matters Evidence
What is the material? Hazard depends on composition, not just dust quantity. Safety data sheet, material specification or survey. Sources: HSE - COSHH.
What creates the dust? Controls should target the source task. Task observation and method statement. Sources: HSE - COSHH.
Which fraction matters? Respirable and inhalable dust affect different body areas. Sampling strategy or professional judgement. Sources: HSE - COSHH.
Who is exposed? Bystanders, cleaners and maintenance workers may be exposed too. Exposure group map. Sources: HSE - COSHH.
Are controls effective? LEV, water and RPE often fail through poor selection or maintenance. Inspection, testing, monitoring and worker feedback. Sources: HSE - COSHH.
What happens to settled dust? Poor cleaning can re-suspend dust or create explosion risk. Cleaning method and housekeeping inspection. Sources: HSE - COSHH.

Apply the guidance to this garage

Follow the extracted air beyond the hood. Ducts, joints, air-cleaning equipment, fan, airflow indication and discharge all contribute to the system. Capturing fume inside while discharging it onto a public footpath transfers the exposure. The job is ready only when the whole control route and the neighbouring work are suitable and functioning.

The source section sets out the wider principles. In the garage, apply them to this exact observation: A powered sander has a disconnected extraction hose and dust settles on nearby work. The worker’s immediate protective response is Stop the uncontrolled task and restore suitable on-tool extraction or LEV. The supervisor must then resolve the arrangement and verify A competent person checks extraction performance at the sander, including hoses and filters; the supervisor observes effective use and separation from nearby workers.

Fictional applied case

A replacement hose fits the sander, but the extraction indicator remains outside its normal range. The vehicle is due for collection today.

Open the interactive lesson and check →

Body preparation: capture dust before it travels

Dust control is successful when it prevents exposure during the real task, including exposure of neighbouring workers.

A source hood connects through ductwork to a filter collector with a closed waste box, a fan and an outlet passing through the building wall. A separate red low-wall outlet exposes a pavement and is labelled a scene fault. Bent and straight routes compare resistance without claiming measured performance; collection is labelled for dust or fume.

Understand the garage task

Follow the sander in this repair bay to its disconnected hose. Sanding filler, coatings and body materials creates a mixture that must be identified from product information. Fine airborne particles can be inhaled even when there is no dramatic cloud. Dust on the neighbouring workbench suggests that the failed connection affects more than the operator: other repairers, cleaners and anyone passing the bay can share the exposure.

Start by reducing unnecessary sanding and choosing a suitable lower-dust preparation method. Where powered sanding remains necessary, effective on-tool extraction captures material as it is generated; separating preparation work helps prevent spread. The collector, filter and sealed waste container must suit the actual dust. Duct shape alone does not prove airflow. Check the system during sanding, and select any additional respiratory protection from the assessment.

An adult chest cutaway showing the trachea dividing into branching airways within two lungs, ribs at the sides and the domed diaphragm below.View full detail ↗
Lungs and airways in the chest

Locate the lungs, branching airways and diaphragm below them. The cutaway reveals structures normally hidden by the chest wall.

Trace the source-to-breathing-zone route in this lesson. Which change would prevent the contaminant reaching the person?

educational illustration · healthy anatomy; enlarged details and teaching colours.

What effective control looks like

How should dust risk be assessed?

Dust risk should be assessed by material, task, exposure route, particle size, control effectiveness and worker health risk.

A suitable COSHH assessment names the substance and task. It should not simply state 'dust present'. It should identify whether the dust contains silica, wood, flour, cement, metals, biological material, toxic additives or combustible material, and separately identify suspected asbestos or lead for their own legal routes.

The assessment should describe who is exposed, how close they are to the source, how long the task lasts, whether the task is indoors or outdoors, what extraction is used, whether water suppression is effective, how cleaning is done and whether other workers nearby are exposed.

If there is uncertainty, exposure monitoring or specialist occupational hygiene advice may be needed. Monitoring should answer a management question: are controls adequate, which task is worst, who is exposed, is the WEL exceeded, or does a control improvement work? See HSE - COSHH.

Dust assessment questions - Dust assessment questions
Question Why it matters Evidence
What is the material? Hazard depends on composition, not just dust quantity. Safety data sheet, material specification or survey. Sources: HSE - COSHH.
What creates the dust? Controls should target the source task. Task observation and method statement. Sources: HSE - COSHH.
Which fraction matters? Respirable and inhalable dust affect different body areas. Sampling strategy or professional judgement. Sources: HSE - COSHH.
Who is exposed? Bystanders, cleaners and maintenance workers may be exposed too. Exposure group map. Sources: HSE - COSHH.
Are controls effective? LEV, water and RPE often fail through poor selection or maintenance. Inspection, testing, monitoring and worker feedback. Sources: HSE - COSHH.
What happens to settled dust? Poor cleaning can re-suspend dust or create explosion risk. Cleaning method and housekeeping inspection. Sources: HSE - COSHH.

Verify before release

Use the evidence in a repair decision

Dust control is successful when it prevents exposure during the real task, including exposure of neighbouring workers.

For this case, the observation is: A powered sander has a disconnected extraction hose and dust settles on nearby work. Keep the observation distinct from an inferred cause. Fine body-preparation dust can damage health and expose people beyond the tool operator. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

A replacement hose fits the sander, but the extraction indicator remains outside its normal range. The vehicle is due for collection today.

Open the interactive lesson and check →

Grinding: make the equipment fit the repair

An awkward repair is a reason to change the method or equipment, not a reason to remove its safeguards.

Detailed guarded angle grinder above a repair panel secured in a bench vice. The wheel, operator-side guard, handles and motor housing are distinct. Red spark lines face a controlled work area, while a rigid screen separates another worker from the operation.

Understand the garage task

The guard has been removed to reach the vehicle’s panel edge. This changes the protection around a fast rotating abrasive product and exposes the operator to contact, fragments and ejected material. A short finishing job can still produce a serious injury. Eye protection addresses only part of the possible harm; it cannot substitute for a suitable tool, effective guard and controlled workpiece.

Consider whether the finish can be achieved without grinding or with a more suitable guarded tool. Match the abrasive product, dimensions, speed rating, mounting and intended use to the manufacturer’s instructions and the material. A cutting disc must not be treated as a grinding disc. Body coatings also introduce dust and fume questions, while sparks can reach trim and solvent waste. Equipment suitability, extraction, fire precautions and protection of others therefore need to be planned together.

What effective control looks like

How can the ISO 45001 hierarchy of controls guide safe equipment selection and risk reduction under PUWER?

Eliminate, Reduce including substitution, Isolate, Control, personal protective equipment (PPE) and Discipline (ERICPD) is a prompt for decisions. HSE’s five-level hierarchy prioritises elimination, substitution, engineering controls, administrative controls and PPE. They are related frameworks, not identical laws; apply them to the actual task and check the resulting control.

Eliminate the dangerous intervention by redesigning the process or buying equipment that does not jam. Verify that cleaning and maintenance can be done without reaching dangerous parts.

Reduce or substitute equipment, material or task design to lower the risk. During purchasing, compare the intended use, environment, user and maintenance access, not only price or conformity marking.

Isolate dangerous motion with suitable fixed or interlocked guarding, safe controls and energy isolation; test the safeguards under real cleaning and jam-clearing conditions. Competent engineering review is needed when modifying safety functions.

Control, PPE and Discipline: inspection, maintenance, training, supervision and PPE support physical protection. They cannot make an exposed moving blade or nip point acceptable when guarding is feasible. ERICPD is a practical prompt; HSE’s five-level hierarchy is related but distinct.

Source: HSE hierarchy of controls

Source: HSE PUWER overview

How can the ERICPD hierarchy of controls guide safe equipment selection and risk reduction under PUWER?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

ERICPD control levelTopic-specific exampleSource and full task context
EliminateAvoid the dangerous local task where feasible by redesign or pre-completed work.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview
ReduceAssess a suitable lower-hazard equipment/process replacement; simple exposure reduction is not substitution.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview
IsolateApply the statutory guarding order and effective physical isolation/control of dangerous energy.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview
ControlPlan inspection, maintenance, authorisation, training, supervision and safe handback under the actual regime.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview
PPESelect relevant residual protective equipment; no wearable item makes an exposed moving nip or blade acceptable.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview
DisciplineVerify condition and competence, stop on unreliable interlocks and revalidate changes before release.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview

How can the ISO 45001 hierarchy of controls guide safe equipment selection and risk reduction under PUWER?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

ESEAP control levelTopic-specific exampleSource and full task context
EliminationAvoid the dangerous local task where feasible by redesign or pre-completed work.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview
SubstitutionAssess a suitable lower-hazard equipment/process replacement; simple exposure reduction is not substitution.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview
Engineering controlsApply the statutory guarding order and effective physical isolation/control of dangerous energy.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview
Administrative controlsPlan inspection, maintenance, authorisation, training, supervision and safe handback under the actual regime.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview
PPESelect relevant residual protective equipment; no wearable item makes an exposed moving nip or blade acceptable.Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE PUWER overview

Verify before release

Use the evidence in a repair decision

An awkward repair is a reason to change the method or equipment, not a reason to remove its safeguards.

For this case, the observation is: A grinder’s guard is removed to reach a panel edge. Keep the observation distinct from an inferred cause. Contact, ejected material or wheel failure can injure the operator and others. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

The correct guard blocks access to a narrow wheel-arch edge. A repairer suggests removing it for the final few seconds.

Open the interactive lesson and check →

Welding fume: the source must stay inside the capture zone

Follow the contaminant from the weld to its final destination; a working hood is not the end of the assessment.

A source hood connects through ductwork to a filter collector with a closed waste box, a fan and an outlet passing through the building wall. A separate red low-wall outlet exposes a pavement and is labelled a scene fault. Bent and straight routes compare resistance without claiming measured performance; collection is labelled for dust or fume.

Understand the garage task

Here, fume crosses the welder’s face before reaching the hood. The fan may run, yet the hood is not controlling the source. Welding fume can cause serious respiratory disease, including cancer. Escaping fume can also expose neighbouring repairers without respiratory protection.

First consider an approved cold joining method or a lower-fume repair process that remains compatible with the vehicle repair specification. For the welding shown, position suitable source capture so the plume is intercepted before it enters the breathing zone; move the hood as the weld moves. Assess remaining exposure and suitable respiratory protection, including protection of others. A visor alone is not RPE. Trace the dedicated fume system through filtration and discharge: the low outlet outside is a separate deliberate hazard, so capture inside is only one part of the solution.

An adult chest cutaway showing the trachea dividing into branching airways within two lungs, ribs at the sides and the domed diaphragm below.View full detail ↗
Lungs and airways in the chest

Locate the lungs, branching airways and diaphragm below them. The cutaway reveals structures normally hidden by the chest wall.

Trace the source-to-breathing-zone route in this lesson. Which change would prevent the contaminant reaching the person?

educational illustration · healthy anatomy; enlarged details and teaching colours.
A realistic eye with lids, lashes and a hazel iris beside an enlarged side cutaway showing the cornea, lens, inner retinal lining and optic nerve.View full detail ↗
The eye: surface and cutaway

Compare the visible eye with its enlarged side cutaway. Locate the clear front, lens and inner rear lining before following light and visual signals.

Distinguish the protective eye surface from the internal visual pathway. What task-specific protection or workstation change does this lesson require?

educational illustration · healthy anatomy; enlarged details and teaching colours.

What effective control looks like

What does a strong accident repair centre example look like?

A worked example helps learners see how LEV connects COSHH, RPE, occupational health and daily supervision.

A busy accident repair centre repairs a side impact on a car. The team strips, fills and sands body panels, cleans surfaces, masks the vehicle, mixes a 2K product, sprays primer and topcoat in the booth, uses bake mode, cleans the gun and then polishes the finish. There are multiple airborne hazards: filler dust during sanding, solvent vapour during cleaning, isocyanate mist during spraying, and contaminated surfaces during clean-up.

The centre's controls should not start and end with a booth certificate. The sander needs effective on-tool extraction; the booth needs current TExT, functioning filters and displayed clearance time; the sprayer needs air-fed BA and training; the supervisor needs to stop spraying outside the booth; biological monitoring checks whether exposure is really controlled; and health surveillance identifies possible occupational asthma or dermatitis early, prompting clinical assessment and action to prevent further harmful exposure. Symptoms may already reflect sensitisation; surveillance cannot guarantee detection before sensitisation or replace exposure prevention.

Task stageLEV or ventilation controlDiploma-level learning point
Body filler sandingUse on-tool extraction matched to the sander and dust extractor.Dust control starts before the paint booth stage.
Surface cleaningUse controlled ventilation and avoid solvent vapour build-up.Vapour control may involve COSHH and DSEAR thinking.
Mixing 2K paintUse controlled area, lids, small quantities and ventilation.LEV may not control all skin/splash risks; COSHH must cover routes.
SprayingUse the booth/room with air-fed BA, no bystanders and no visor lifting.The booth and BA operate as a combined barrier system.
Bake/curingMaintain booth airflow/balance and prevent leakage during operating modes.Filter loading or failed pressure sensors can reverse the expected control.
Clearance periodWait for displayed clearance time or keep BA on until clear/outside.The hazard may be invisible after the trigger is released.
Gun cleaningControl aerosol/vapour and avoid spraying cleaner without protection.Post-spray tasks can create exposure if not assessed.
Monitoring reviewUse biological monitoring and symptom reports to test real exposure control.Health evidence can reveal failures that airflow readings miss.

Verify before release

Use the evidence in a repair decision

Follow the contaminant from the weld to its final destination; a working hood is not the end of the assessment.

For this case, the observation is: The welder’s hood is too far from the weld and the fume plume crosses the breathing zone. Keep the observation distinct from an inferred cause. Welding fume can cause serious lung disease, including cancer; nearby workers may also be exposed. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

The hood is repositioned and now captures the plume, but its duct still ends over the outside pavement.

Open the interactive lesson and check →

Hot work: follow heat and sparks into hidden spaces

A hot-work permit records agreed controls; it cannot make an uncontrolled fire pathway safe.

Two technical views link fire prevention and escape. A vehicle panel cutaway highlights heat reaching hidden trim, with closed waste storage and conflicting flammable stock marked for removal. A separate reception view shows a clear continuous route through an available exit and onward outside; parts storage is outside that route. Leaders explain ignition pathways, coordinated work and evacuation.

Understand the garage task

The welder is close to vehicle trim and an open container of solvent-contaminated rags. Look beyond the weld: sparks and conducted heat can reach the opposite side of a panel, insulation and enclosed cavities. A fire can develop after the tool stops. Nearby paint preparation and waste handling create interfaces, so an apparently small body repair needs more than an extinguisher placed beside the operator.

Prefer a suitable cold method where the approved repair allows it. If hot work remains necessary, inspect the vehicle and surrounding area, remove combustible material and control flammable substances before authorisation. Use a permit where the site’s assessment calls for formal work coordination, but remember that a signed form is an administrative control. Its listed precautions must exist at the job. Fire-watch and follow-up arrangements should match the work and competent assessment; this learning scene does not supply a universal waiting time.

What effective control looks like

How can the ISO 45001 hierarchy of controls reduce task risks before relying on a permit-to-work?

Consider the planned opening of hydrocarbon pump P-204. The harm chain is residual liquid or vapour in a line, release through the opened flange, then skin contact, inhalation or ignition. Odour, pressure, a failed drain or a changed adjacent operation are warnings to stop. The HSE five-level hierarchy is elimination, substitution, engineering, administrative controls and PPE; ERICPD expresses Eliminate, Reduce including substitution, Isolate, Control, PPE and Discipline. A permit sits in the administrative layer and cannot replace the physical barriers.

Eliminate or redesign: the maintenance planner checks whether the repair can be completed without opening the line, or whether the pump can be taken fully out of service and worked on in a controlled workshop. Operations checks process feasibility and the work pack records why intrusive work remains necessary. If production pressure prevents a safe shutdown, the job is held rather than authorised on a weaker permit.

Substitute or reduce: engineering considers a less hazardous cleaning medium or reduced inventory and pressure before opening, only if process compatibility and the approved procedure allow it. Operations verifies the actual substance and condition against drawings and process information. Assuming a line is empty because a gauge reads zero is a failure mode; unexpected contents require withdrawal and reassessment.

Isolate and engineer: the isolation authority selects a risk-based physical isolation scheme under HSE HSG253, identifies the exact line, secures energy sources, drains and vents to a safe system, and proves the boundary before work. The issuer and acceptor walk the site against the certificate and drawings; evidence includes lock/valve status, test results and a field check. A passing valve, blocked drain, wrong tag or failed test stops the job. See HSE HSG253 safe isolation guidance.

Control, PPE and Discipline: the area authority coordinates simultaneous operations, gas-test timing, permitted scope, time limit, fire/containment arrangements and shift handover under HSG250. The performing team uses substance-specific eye, hand and body protection selected from the safety data and task assessment, checks condition and replacement, and understands its limits against vapour or ignition. Supervisors sample live permits in the field and investigate repeated corrections. If atmosphere, scope, plant state or adjacent work changes, suspend, make safe and reauthorise only after controls are reverified.

Control-order source: HSE - Hierarchy of controls

How can the ERICPD hierarchy of controls reduce task risks before relying on a permit-to-work?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Pump P-204: line break and handback
Activity and exposure
Replace a gasket on hydrocarbon pump P-204 at a fuel terminal during a planned shutdown.
Before work
Identify the exact flange and boundary, plan the isolation, drain and vent to a safe route, and check concurrent work.
During the activity
Issuer and acceptor verify the field condition and test evidence; the team follows the authorised scope and monitors change.
Hold or stop
A passing valve, blocked drain, residual pressure, odour, gas alarm or conflicting operation suspends the job for reassessment.
Hand-back and release
Check guarding, cleanliness and controlled removal of isolation before authorised plant return.
Evidence to retain
Permit, isolation certificate, test record, field check, stop/reissue history and signed handback.
Decision owner
Duty manager or competent task owner
Full example
Read the activity, checks and hand-back in context
ERICPD control levelTopic-specific exampleSource and full task context
EliminateAvoid opening the line if a feasible redesign or non-intrusive repair removes that intervention.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls
ReduceAssess a less hazardous compatible cleaning medium; lowering pressure or inventory is reduction, not itself substitution.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls
IsolateImplement and prove the risk-based physical isolation, secure energy sources and safe drain/vent boundary.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls
ControlCoordinate simultaneous operations, scope, gas-test timing, authorisation, suspension, revalidation and shift handover.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls
PPESelect substance/task-specific eye, hand and body protection; check suitability and condition. PPE does not repair failed isolation.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls
DisciplineVerify field conditions and follow the stop/reissue/handback system; changed conditions require reassessment.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls

How can the ISO 45001 hierarchy of controls reduce task risks before relying on a permit-to-work?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Pump P-204: line break and handback
Activity and exposure
Replace a gasket on hydrocarbon pump P-204 at a fuel terminal during a planned shutdown.
Before work
Identify the exact flange and boundary, plan the isolation, drain and vent to a safe route, and check concurrent work.
During the activity
Issuer and acceptor verify the field condition and test evidence; the team follows the authorised scope and monitors change.
Hold or stop
A passing valve, blocked drain, residual pressure, odour, gas alarm or conflicting operation suspends the job for reassessment.
Hand-back and release
Check guarding, cleanliness and controlled removal of isolation before authorised plant return.
Evidence to retain
Permit, isolation certificate, test record, field check, stop/reissue history and signed handback.
Decision owner
Duty manager or competent task owner
Full example
Read the activity, checks and hand-back in context
ESEAP control levelTopic-specific exampleSource and full task context
EliminationAvoid opening the line if a feasible redesign or non-intrusive repair removes that intervention.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls
SubstitutionAssess a less hazardous compatible cleaning medium; lowering pressure or inventory is reduction, not itself substitution.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls
Engineering controlsImplement and prove the risk-based physical isolation, secure energy sources and safe drain/vent boundary.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls
Administrative controlsCoordinate simultaneous operations, scope, gas-test timing, authorisation, suspension, revalidation and shift handover.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls
PPESelect substance/task-specific eye, hand and body protection; check suitability and condition. PPE does not repair failed isolation.Read the full task example, checks and stop points on this page. HSE HSG253 safe isolation guidance · HSE - Hierarchy of controls

Verify before release

Use the evidence in a repair decision

A hot-work permit records agreed controls; it cannot make an uncontrolled fire pathway safe.

For this case, the observation is: Sparks travel toward vehicle trim and an open container of contaminated rags. Keep the observation distinct from an inferred cause. Hidden combustible material and flammable residues can ignite during or after the repair. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

The rags are removed. The repairer can still see plastic trim behind the panel, but the customer is waiting and a permit is signed.

Open the interactive lesson and check →

Extraction must not move the exposure onto the pavement

Good extraction protects the source operator, neighbouring workers and people at the discharge. Follow the contaminant all the way outside.

A source hood connects through ductwork to a filter collector with a closed waste box, a fan and an outlet passing through the building wall. A separate red low-wall outlet exposes a pavement and is labelled a scene fault. Bent and straight routes compare resistance without claiming measured performance; collection is labelled for dust or fume.

Understand the garage task

Follow the welding duct through the wall to its low outlet above the pavement. Captured fume can reach passers-by or return through doors and ventilation intakes. The collector does not prove every contaminant has been removed: filters have different purposes and can deteriorate. Little visible smoke is not evidence that this discharge arrangement protects people.

A competent specialist must review the chain from welding to final discharge, including suitable cleaning, replacement air, fan duty and ductwork. Safe outdoor dispersal depends on the building, openings and wind-driven recirculation; turning an elbow upwards is not a complete assessment. Changing the outlet can alter resistance and capture indoors. Before restart, commissioning and appropriate checks should demonstrate effective control and establish benchmarks for ongoing use.

What effective control looks like

What happens when a new workpiece changes the capture conditions?

A normal indicator reading describes one measured condition, not every possible use of the system. A changed workpiece, emission direction, operator position or simultaneous hood use can defeat capture even where the fan runs and a familiar gauge remains in range. Screen changes before using the new process as routine work. Related guidance: Commission your LEV system.

In an illustrative fabrication workshop, a bench extraction hood was commissioned for a small component held inside its defined working zone. A larger component requires the operator to stand between the emission and hood and rotate the piece during finishing. The supervisor holds the changed operation. The old commissioning report remains valuable evidence of the previous configuration, but it does not establish control of the new one. Related guidance: Commission your LEV system.

The process owner and competent LEV specialist establish the substances, emissions, work rate, operator movements and simultaneous demands. They consider source reduction and improved enclosure or task layout before treating greater fan output as the answer. Any change to ducts, fan, filtration or discharge needs assessment of system balance, contaminant compatibility and fire/explosion or re-entry consequences where relevant. Related guidance: Commission your LEV system.

The acceptance test represents the intended operation and relevant adverse conditions. It observes capture or containment and compares defined technical measurements with the appropriate design and commissioning benchmarks. Where the hazard or uncertainty calls for it, competent exposure assessment supports the decision. A visually clear room or one airflow number cannot alone establish adequate control of an invisible harmful contaminant. Related guidance: Commission your LEV system.

Before release, provide a comprehensible record of the authorised process/configuration, hood use, indicators and action limits, restrictions, maintenance and user instruction. The operator demonstrates the new working zone and a stop when the arrangement cannot be maintained. Update the schematic, manual, logbook and future examination basis; retain the earlier configuration history so later changes can be traced. Related guidance: Commission your LEV system.

Guidance for these decisions: Commission your LEV system; HSG258 controlling airborne contaminants; LEV frequently asked questions. Apply the legal route for the work location; illustrative scenarios are SHARE teaching examples.

Verify before release

Use the evidence in a repair decision

Good extraction protects the source operator, neighbouring workers and people at the discharge. Follow the contaminant all the way outside.

For this case, the observation is: The welding-fume duct ends low on the outside wall, pointing down over a pedestrian pavement. Keep the observation distinct from an inferred cause. Discharged contaminants can reach pedestrians and workers or be drawn back through openings and air intakes. A fitted filter does not prove the outlet air is safe. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

A new filter bag is fitted and the fan sounds stronger. The outlet still points down across the pavement beside an open workshop door.

Open the interactive lesson and check →

Capture exhaust at the tailpipe and discharge it safely

Effective exhaust control follows the pollutant from its source to a safe destination; moving it elsewhere is not enough.

A source hood connects through ductwork to a filter collector with a closed waste box, a fan and an outlet passing through the building wall. A separate red low-wall outlet exposes a pavement and is labelled a scene fault. Bent and straight routes compare resistance without claiming measured performance; collection is labelled for dust or fume.

Understand the garage task

The engine is idling indoors while the extraction hose lies disconnected. Pollutants can move through the mechanical bays and into adjacent occupied areas before anyone sees smoke. Exhaust can contain carbon monoxide and other harmful substances; smell, a clear-looking plume and the presence of a catalytic converter do not establish safe air. The technician at the car is not the only person potentially exposed.

Eliminate unnecessary engine running. When static running is required, connect suitable effective tailpipe extraction and provide appropriate ventilation. Follow the whole route from connection through ducting to a safe external discharge, avoiding people, doors, windows and air intakes. A dry-dust collection bag is not a control for all exhaust gases. A running fan or an open workshop door cannot substitute for proving that emissions are captured and discharged safely during the actual task.

What effective control looks like

How should welding and sanding be controlled in a workshop?

At fictional Riverside Leisure Ltd, general room ventilation remains for fresh air, while welding fume and dry sanding dust need assessed source capture and verification.

A maintenance workshop has a welding bay and a shared sanding bench. Before work, the supervisor identifies metal and coating, dust material, other workers and the actual hood or on-tool extraction. The trained workers check the hood position, hose, flow indication and collector. During work, they observe whether fume and dust enter capture without crossing their breathing zones; doors and cross-draughts are controlled. If a hose splits or a new coating is unknown, the task stops and other workers are kept clear. Maintenance repairs the system and a competent person verifies effective capture under the real task. Completion includes contained dust waste, defect record, rebrief and any exposure reassessment. See HSE.

Basis: HSE Common LEV processes and sources; HSE Welding LEV maintenance and testing; HSE LEV frequently asked questions

Riverside workshop source capture

Task material and setting: Weld a repaired steel fitting and sand a wooden panel in a fictional leisure-centre maintenance workshop; coating identity must be known.

People and prerequisites: Welder, joiner, supervisor and nearby staff; COSHH assessment, suitable hood/on-tool unit, trained users and current performance basis.

Before: Confirm material and emission, other occupants, hood/tool match, hose/filter and flow indication.

During: Keep source in capture zone; observe fume and dust with actual doors and simultaneous work.

Hold or stop: Stop for split hose, low flow, escaping plume or unknown coating; protect other staff and escalate.

Completion and hand back: Contain waste, repair and competently verify capture, update assessment and brief users.

Evidence: Task assessment, pre-use check, defect, repair, verification and exposure decision.

Verify before release

Use the evidence in a repair decision

Effective exhaust control follows the pollutant from its source to a safe destination; moving it elsewhere is not enough.

For this case, the observation is: An engine is running in the bay while the extraction hose lies disconnected. Keep the observation distinct from an inferred cause. Exhaust can contain carbon monoxide and other harmful pollutants; visible smoke is not a reliable warning. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

The hose adapter does not fit this car. A colleague opens the roller door and proposes leaving the engine running until another adapter arrives.

Open the interactive lesson and check →

Capstone: decide whether the job may proceed

Combine the observations, restrictions and verification into one justified work decision.

Read the whole case before releasing a part

A welder positions the extraction hood on the far side of their head. A grinder guard has been removed for access, solvent-soaked waste sits behind the panel and the extractor outlet faces a pedestrian path. The fan sounds normal and the repair is almost finished.

Stop the affected operations, protect nearby people and resolve guarding, hot-work conditions and the complete extraction route before an authorised restart.

Separate immediate protection from the investigation of causes. Use factual observations, the actual equipment and task information, and the appropriate competent roles. Where the evidence is missing, keep the affected operation restricted rather than treating uncertainty as permission.

Build the release evidence

Make the handover usable

State what may proceed, what remains held, who owns each unresolved issue and the evidence required to change the decision. Ask the next person to explain the restriction in their own words. Record a defined review point and communicate any change to affected colleagues, contractors and visitors. A form is useful only when it represents the actual arrangement.

Fictional applied case

A welder positions the extraction hood on the far side of their head. A grinder guard has been removed for access, solvent-soaked waste sits behind the panel and the extractor outlet faces a pedestrian path. The fan sounds normal and the repair is almost finished.

Open the interactive lesson and check →

Take the learning into a real briefing

Turn the selected control into a clear question, observation and review trigger.

Prepare a short toolbox conversation

Choose one relevant task from this course. Describe its current scope, then ask a colleague to identify the people exposed and the control that must work. Avoid asking only whether everyone understands: a useful response explains the action and what would make the job stop.

Separate dusty preparation, maintain capture and choose any additional RPE from the exposure assessment.

For the fictional exercise below, write the observation, harm pathway, immediate protection, responsible role and evidence needed before release. Use the packaged worksheet; do not enter real personal or company information or submit an operational record.

Check the claim against the workplace

Follow up the change

Arrange a proportionate check after the control is used in representative conditions. If the observation contradicts the claimed protection, retain the restriction, report the discrepancy and revisit the assessment. Keep course completion separate from permission to perform specialist work.

Fictional applied case

A welder positions the extraction hood on the far side of their head. A grinder guard has been removed for access, solvent-soaked waste sits behind the panel and the extractor outlet faces a pedestrian path. The fan sounds normal and the repair is almost finished.

Open the interactive lesson and check →