Valeting, cleaning chemicals and wet work

Free online training · Approximate learning time: 110–170 minutes · Self-paced

Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.

110–170 minutes · Includes activities, model practice and assessment.

Independent awareness and decision learning for vehicle repair. Practical competence, EV high-voltage work, asbestos work and other specialist tasks require separate training and authorisation. GB baseline; check corresponding Northern Ireland duties and local arrangements.

Understand this repair environment

Make cleaning work safe for the person doing it and everyone using the surrounding route.

Follow the work, not just the equipment

Cleaning can introduce hazards while removing others. Water, detergent and hoses affect walking surfaces; electrical connections may meet spray; concentrated products can contact skin or eyes; a cleaner used in a vehicle cabin can build exposure in a restricted space. Include set-up, use, moving equipment, clearing waste and reopening the route in the assessment.

Choose a suitable product and method for the actual job. Follow the assessed dilution and use instructions; never mix cleaning products to improve performance. Keep containers identified and available safety information relevant to the substance in use. Arrange ventilation and contact protection for the cabin task, rather than assuming the bottle’s general description covers every situation.

A warning cone is useful information, but the walking route still needs protection, effective drainage and timely removal of contamination. Electrical defects in a wet area require safe withdrawal and competent repair, not a trial to see whether the protective device trips. Handling aids should remove awkward transfers as well as make the longest journey easier. Verify the complete task during representative wet conditions before removing restrictions.

Fictional applied case

The valet team has finished a car, but a hose lies across the customer route and water remains at the doorway. A damaged extension connection is close to the washer. A worker proposes mixing two cleaners for the next cabin and carrying the heavy extractor around the barrier.

Open the interactive lesson and check →

Choose controls that fit the actual task

Use source guidance to distinguish control selection, work instructions and evidence of effectiveness.

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

Control classification: Classify the mechanism separately from its upkeep: physical floor repair, drainage, barriers, protected routes, compartmentation, fire doors and suitable disposal facilities are physical measures where specified. Cleaning schedules, inspections, policies, funding, supervision and verification are administrative arrangements maintaining them. A verbal instruction is not a physical barrier. Read this correction with the source table. Retained overview and stage artwork requires the matching classification update.

Remove or reduce the hazard before relying on procedures or personal protection.

For slips and trips, assess the actual task and first look for a way to remove the hazard. Where that is not possible, consider a safer substitute, engineered separation and then clear work procedures. PPE protects against remaining exposure; it does not make an uncontrolled task safe. HSE hierarchy of controls

The selected measures need a named owner, a usable stop point and a check that they still work when the task or conditions change. In Northern Ireland, verify the separate legal route and site instructions.

For the wet entrance, eliminate recurring water entry at source where practicable. Reduce contamination with suitable matting, drainage and a cleaning method that leaves the route safe; physically prevent access while unsafe and provide an alternative. Repair floor and route defects, then select footwear for residual risk and sustain checks. ERICPD (Eliminate, Reduce, Isolate, Control, PPE, Discipline) is a teaching prompt; Discipline means competent cleaning, supervision and defect closure. HSE slip and trip factors; HSE barriers and cleaning.

How can the ERICPD hierarchy of controls remove slip and trip hazards from workplace routes?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ERICPD control levelTopic-specific exampleSource and full task context
Eliminate

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Reduce

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Isolate

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Control

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Discipline

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ESEAP mapping crosswalk: these are retained ERICPD source rows, mapped to the five ESEAP levels. Read the control-classification correction for mixed physical and administrative measures; six source rows do not mean six ESEAP levels.
Five-level control stage(s)Topic-specific exampleSource and full task context
Elimination

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Administrative controls

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

Apply the guidance to this garage

A warning cone is useful information, but the walking route still needs protection, effective drainage and timely removal of contamination. Electrical defects in a wet area require safe withdrawal and competent repair, not a trial to see whether the protective device trips. Handling aids should remove awkward transfers as well as make the longest journey easier. Verify the complete task during representative wet conditions before removing restrictions.

The source section sets out the wider principles. In the garage, apply them to this exact observation: Foamy water pools beside a hose crossing the pedestrian route. The worker’s immediate protective response is Keep people away from the affected route, clear the hose and remove the pooling water. The supervisor must then resolve the arrangement and verify The supervisor checks the bay during washing: drainage removes water, hoses stay out of walkways and the surface and cleaning arrangements remain suitable.

Fictional applied case

The puddle has been removed, but the hose still crosses the only walkway. The next wash will begin as soon as the vehicle moves.

Open the interactive lesson and check →

Wash-bay slips: design the water and hose out of the route

Check wet-work controls during wet work: drainage, hose routing and cleaning should keep the walking route usable.

Perspective garage floor with a vehicle, wet patch, trailing hose and stored parts, contrasted with a clear walking route and a managed overhead supply. Callouts follow contamination, storage and hose routing.

Understand the garage task

The wash bay has foam and standing water beside a hose crossing the pedestrian route. These are two linked mechanisms: contamination reduces available grip and the hose can catch a foot. A valeter may be looking at the vehicle rather than the ground, while someone arriving from the mechanical bays may not expect a wet surface.

Wet work should be planned so water drains effectively and hoses stay out of walking routes. Suitable surface design and maintenance reduce the likelihood of recurring puddles; a cleaning and drying routine deals with residual contamination. A cone is a temporary warning, not a permanent replacement for these controls. Footwear must suit the surface and contaminants. General safety-boot labelling does not prove slip resistance. Keep vehicle movements separate from any temporary pedestrian diversion.

What effective control looks like

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

Control classification: Classify the mechanism separately from its upkeep: physical floor repair, drainage, barriers, protected routes, compartmentation, fire doors and suitable disposal facilities are physical measures where specified. Cleaning schedules, inspections, policies, funding, supervision and verification are administrative arrangements maintaining them. A verbal instruction is not a physical barrier. Read this correction with the source table. Retained overview and stage artwork requires the matching classification update.

Remove or reduce the hazard before relying on procedures or personal protection.

For slips and trips, assess the actual task and first look for a way to remove the hazard. Where that is not possible, consider a safer substitute, engineered separation and then clear work procedures. PPE protects against remaining exposure; it does not make an uncontrolled task safe. HSE hierarchy of controls

The selected measures need a named owner, a usable stop point and a check that they still work when the task or conditions change. In Northern Ireland, verify the separate legal route and site instructions.

For the wet entrance, eliminate recurring water entry at source where practicable. Reduce contamination with suitable matting, drainage and a cleaning method that leaves the route safe; physically prevent access while unsafe and provide an alternative. Repair floor and route defects, then select footwear for residual risk and sustain checks. ERICPD (Eliminate, Reduce, Isolate, Control, PPE, Discipline) is a teaching prompt; Discipline means competent cleaning, supervision and defect closure. HSE slip and trip factors; HSE barriers and cleaning.

How can the ERICPD hierarchy of controls remove slip and trip hazards from workplace routes?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ERICPD control levelTopic-specific exampleSource and full task context
Eliminate

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Reduce

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Isolate

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Control

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Discipline

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

How can the ISO 45001 hierarchy of controls remove slip and trip hazards from workplace routes?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Wet leisure-centre entrance
Activity and exposure
Wet entrance at a public leisure centre during heavy rain.
Before work
Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.
During the activity
Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.
Hold or stop
Do not reopen while the floor remains wet or the alternate route creates another hazard.
Hand-back and release
Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.
Evidence to retain
Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.
Full example
Read the activity, checks and hand-back in context
ESEAP mapping crosswalk: these are retained ERICPD source rows, mapped to the five ESEAP levels. Read the control-classification correction for mixed physical and administrative measures; six source rows do not mean six ESEAP levels.
Five-level control stage(s)Topic-specific exampleSource and full task context
Elimination

Remove recurring water entry at source where practicable.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Use suitable matting, drainage and safe cleaning.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls

Prevent access while unsafe and provide an alternative route.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Engineering controls / Administrative controls

Repair floor and route defects.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
PPE

Select suitable footwear for residual risk.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning
Administrative controls

Maintain competent cleaning, inspections and defect closure.

Read the full task example, checks and stop points on this page. HSE hierarchy of controls · HSE slip and trip factors · HSE barriers and cleaning

Verify before release

Use the evidence in a repair decision

Check wet-work controls during wet work: drainage, hose routing and cleaning should keep the walking route usable.

For this case, the observation is: Foamy water pools beside a hose crossing the pedestrian route. Keep the observation distinct from an inferred cause. Water, detergent and trailing equipment make slips and trips likely. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

The puddle has been removed, but the hose still crosses the only walkway. The next wash will begin as soon as the vehicle moves.

Open the interactive lesson and check →

Wet-bay electricity: a protective device is not a repair

Prevent contact with the defect, isolate safely and verify the repair before the washer returns to the wet bay.

Three technical panels show a secured electrical isolator and disconnected inspection lamp, a compressor receiver with motor, gauge and outlet valve, and an electric car with battery, damaged cable indication and controlled key. Each energy source has its own numbered control.

Understand the garage task

The pressure washer’s damaged electrical connection is lying in water. Wet conditions can increase the consequences of an electrical defect, exposing the operator and anyone touching connected equipment to shock. The machine running, or a past inspection label, does not establish present safety. Handling the wet connector to see whether it works can make the situation worse.

Stop use and arrange safe isolation without touching damaged live parts or entering danger. Competent people must repair or replace defective equipment and establish safe return to service. Select equipment and connections suitable for the wash environment and provide the appropriate residual current device protection. An RCD is an additional safeguard, not protection against every fault or permission to tolerate damage. Cable routing, splash protection, inspection and maintenance should suit the equipment and actual conditions, rather than a generic fixed testing interval.

What effective control looks like

What electrical control sequence prevents exposure?

Start by removing unnecessary electrical exposure and selecting suitable equipment. Then protect conductors, secure and prove isolation for work, inspect for deterioration, and hand back only after competent verification.

Best-practice guide · six simple steps

Best-practice guide: Electrical control measures, safe systems and inspection

Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.

Step 1 of 6 · StartThis cardPNG imagePDFView full sizeAll 6 cardsPNG images (ZIP)PDF (6 pages)

Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains one card per page. Read the full topic for explanations, questions and source links.

Read all six steps as text
  1. 1. What electrical control sequence prevents exposure?

    Start by removing unnecessary electrical exposure and selecting suitable equipment.

    • Avoid / redesign: Use external diagnostics or remove the faulty equipment from use where that avoids exposed electrical work.
    • Control the task: Securely isolate relevant supplies, prevent reconnection and prove dead using the approved safe-isolation method.
    • Verify before release: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.

    Start by removing unnecessary electrical exposure and selecting suitable equipment. Then protect conductors, secure and prove isolation for work, inspect for deterioration, and hand back only after competent verification. Electrical safety depends on suitable design, protection, secure isolation and inspection that finds defects before people are exposed.

    Apply it: Which part of this plan would you check at the workface before authorising the task?

    Read this part of the full topicOpen the full topicHSE - Introduction to electrical safety (Great Britain)HSE - Electricity at work: safe working practices HSG85 (Great Britain)HSE - Electrician suffered shock when supply had not been properly isolated (Great Britain)
  2. 2. Turn electrical control measures, safe systems and inspection knowledge into a decision

    Use the evidence to improve the actual work arrangement.

    • Change at source: Use external diagnostics or remove the faulty equipment from use where that avoids exposed electrical work.
    • Make it observable: If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
    • Keep useful evidence: Revised work pack, isolation and test record, briefing, certificate and defect closure.

    Electrical safety depends on suitable design, protection, secure isolation and inspection that finds defects before people are exposed. A damaged conductor, failed protective device or unexpected supply can cause shock, arc injury or fire even where a test label is current. Revised work pack, isolation and test record, briefing, certificate and defect closure.

    Apply it: What evidence would show that the change improves this task, rather than only completing a record?

    Read this part of the full topicOpen the full topicHSE - Electrician suffered shock when supply had not been properly isolated (Great Britain)HSE - Introduction to electrical safety (Great Britain)HSE - Electricity at work: safe working practices HSG85 (Great Britain)
  3. 3. A field decision from start to hand-back

    Fictional example: a practical application of the existing topic lesson.

    • Setting: the site team opens a refurbished wall where a cable route is uncertain.
    • Act: Stop intrusive work, protect the area, identify all possible supplies and agree a revised method.
    • Hold / review: Any unidentified conductor, unexpected voltage or changed scope stops the job.

    Competent lead locates, isolates and proves the circuit dead at the work point; supervisor keeps other trades clear. Restore guards and supply only after people clear; give the client an updated circuit record.

    Apply it: At which point would you hold this example, and what evidence would allow it to proceed?

    Read this part of the full topicOpen the full topicHSE - Introduction to electrical safety (Great Britain)HSE - Electricity at work: safe working practices HSG85 (Great Britain)
  4. 4. Electrical harm mechanisms

    Connect the task, the route to the person and the control that can fail.

    • Electric shock: Current passes through the body after contact with live parts.
    • Electrical burns: Current heats tissue or arc energy burns skin and eyes.
    • Loss of muscle control: Shock causes spasm, inability to let go or a fall.

    Electric shock: Current passes through the body after contact with live parts. Electrical burns: Current heats tissue or arc energy burns skin and eyes. Loss of muscle control: Shock causes spasm, inability to let go or a fall.

    Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?

    Read this part of the full topicOpen the full topicHSE - Introduction to electrical safety (Great Britain)HSE - Electricity at work: safe working practices HSG85 (Great Britain)
  5. 5. Choose controls for electrical control measures, safe systems and inspection

    Start with the stronger practicable options and verify their effect.

    • Elimination: Use external diagnostics or remove the faulty equipment from use where that avoids exposed electrical work.
    • Engineering controls: Use a suitable off-line test or replaceable module where it safely proves the fault without exposed live conductors.
    • Engineering controls: Securely isolate relevant supplies, prevent reconnection and prove dead using the approved safe-isolation method.
    • Engineering controls: Provide suitable enclosures, protective devices and test equipment for the actual circuit and installation.
    • Administrative controls: Confirm circuit identity, competence, test scope and restart authority; separately justify and control any unavoidable energised test.

    Elimination: Use external diagnostics or remove the faulty equipment from use where that avoids exposed electrical work. Engineering controls: Use a suitable off-line test or replaceable module where it safely proves the fault without exposed live conductors. Engineering controls: Securely isolate relevant supplies, prevent reconnection and prove dead using the approved safe-isolation method. Engineering controls: Provide suitable enclosures, protective devices and test equipment for the actual circuit and installation. Administrative controls: Confirm circuit identity, competence, test scope and restart authority; separately justify and control any unavoidable energised test. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.

    Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?

    Read this part of the full topicOpen the full topicHSE - Electrician suffered shock when supply had not been properly isolated (Great Britain)
  6. 6. Use the full electrical control measures, safe systems and inspection lesson

    Follow the official sources below and retain the task-specific evidence.

    • Official guidance: HSE - Introduction to electrical safety
    • Official guidance: HSE - Electricity at work: safe working practices HSG85
    • Task decision: Revised work pack, isolation and test record, briefing, certificate and defect closure.

    Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status.

    Apply it: Which official source and full-topic section will you use to resolve the next decision?

    Read this part of the full topicOpen the full topicHSE - Introduction to electrical safety (Great Britain)HSE - Electricity at work: safe working practices HSG85 (Great Britain)HSE - Electrician suffered shock when supply had not been properly isolated (Great Britain)

Simplified learning guide. Use the full topic, current official guidance and the actual work arrangements. Workplace scenarios labelled fictional are illustrative examples.

A safe method links design to the person at the work point: a labelled switch is insufficient if a second supply or stored charge remains. A supervisor should identify who can isolate, who proves dead, and what change would stop the task before tools approach conductors.

Verify before release

Use the evidence in a repair decision

Prevent contact with the defect, isolate safely and verify the repair before the washer returns to the wet bay.

For this case, the observation is: A washer’s damaged power connection lies on the wet floor. Keep the observation distinct from an inferred cause. Water and damaged electrical equipment can cause fatal shock. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

A colleague points to the RCD and says the damaged connector can be kept dry with a towel until the shift ends.

Open the interactive lesson and check →

Interior valeting: the small space changes chemical exposure

Assess the actual cabin task, not just the bottle: product choice, ventilation and contact control must work together.

Three connected workplace-control illustrations show closed labelled paint tins in a spill tray, a ventilated mixing bench with rear capture slots, and a shaped chemical glove beside a stocked washing basin. Numbered leaders distinguish product identification, control at release and separate skin-contact precautions. Product letters are illustrative only.

Understand the garage task

The valeter is using a solvent-based cleaner inside a vehicle with its doors nearly closed. The cabin provides little space for vapour to disperse, and leaning into it brings the breathing zone close to treated surfaces. Splashes and contaminated cloths can expose skin and eyes too. A familiar smell or vehicle-interior branding does not establish safe use in these conditions.

Compare safer suitable cleaning products and methods before relying on ventilation or gloves. Use the task-specific COSHH assessment and product information to control quantities, application, dilution and contact. For work inside vehicles, ventilation includes opening doors and other available openings as appropriate, while assessing whether more ventilation is needed. Position the vehicle so these openings do not create another traffic conflict. Consider flammable vapour and ignition sources alongside health risks, and never assume that mixing products improves performance safely.

A hand and forearm behind an enlarged skin block showing the surface layers, hair follicle, coiled sweat gland and duct, nerves, blood vessels and underlying fat.View full detail ↗
Under the skin surface

Explore an enlarged section of hair-bearing skin, with a hand and forearm for context. Layers, glands, nerves and vessels are enlarged for clarity.

Use the task in this lesson to identify contact, repeated wet work or contamination. Which change reduces contact before relying on gloves?

educational illustration · healthy anatomy; enlarged details and teaching colours.
An adult chest cutaway showing the trachea dividing into branching airways within two lungs, ribs at the sides and the domed diaphragm below.View full detail ↗
Lungs and airways in the chest

Locate the lungs, branching airways and diaphragm below them. The cutaway reveals structures normally hidden by the chest wall.

Trace the source-to-breathing-zone route in this lesson. Which change would prevent the contaminant reaching the person?

educational illustration · healthy anatomy; enlarged details and teaching colours.

What effective control looks like

How can the ISO 45001 hierarchy of controls guide COSHH exposure controls before relying on health surveillance?

Choose prevention and reliable engineering control before procedures or PPE; verify the actual equipment and task.

For isocyanate two-pack spray paint, assess a non-isocyanate coating or off-site process first. If spraying remains, use an enclosed extracted booth with clearance time and suitable air-fed breathing equipment, plus controlled gun cleaning, training and checks. The HSE spray-painter guide specifies these controls; HSENI COSHH sets the NI hierarchy. Stop spraying for failed extraction, unknown clearance time or missing air supply; do not rely on a better mask alone.

On a small screen, scroll this table sideways to read all columns.

How can the ERICPD hierarchy of controls guide COSHH exposure controls before relying on health surveillance?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for What should you know about COSHH control measures and health surveillance?
Activity and release context
For isocyanate two-pack spray paint, assess a non-isocyanate coating or off-site process first. If spraying remains, use an enclosed extracted booth with clearance time and suitable air-fed breathing equipment, plus controlled gun cleaning, training and checks. The HSE spray-painter guide specifies these controls; HSENI COSHH sets the NI hierarchy. Stop spraying for failed extraction, unknown clearance time or missing air supply; do not rely on a better mask alone.
Full example
Read the activity, checks and hand-back in context
Two-pack spray painting
Five-level / ERICPDControl choiceOwner, check, failure and stop
Eliminate / eliminateSpecify non-spray or off-site finished part if feasible.Designer records option; hold spray if safe no-spray route works.
Substitute / reduceSelect compatible lower-hazard coating after assessment.Coatings engineer approves; stop on unknown chemistry.
Engineering / isolate and controlExtracted booth with verified clearance and safe air supply.Booth lead tests; stop on failed extraction or air.
Administrative / disciplineCOSHH assessment, cleaning, maintenance and access control.Supervisor inspects; hold on failed clearance.
PPE / PPETask-specific air-fed RPE and skin protection.Trainer checks; no spray if protection fails.

How can the ISO 45001 hierarchy of controls guide COSHH exposure controls before relying on health surveillance?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for What should you know about COSHH control measures and health surveillance?
Activity and release context
For isocyanate two-pack spray paint, assess a non-isocyanate coating or off-site process first. If spraying remains, use an enclosed extracted booth with clearance time and suitable air-fed breathing equipment, plus controlled gun cleaning, training and checks. The HSE spray-painter guide specifies these controls; HSENI COSHH sets the NI hierarchy. Stop spraying for failed extraction, unknown clearance time or missing air supply; do not rely on a better mask alone.
Full example
Read the activity, checks and hand-back in context
Two-pack spray painting
Five-level / ERICPDControl choiceOwner, check, failure and stop
Eliminate / eliminateSpecify non-spray or off-site finished part if feasible.Designer records option; hold spray if safe no-spray route works.
Substitute / reduceSelect compatible lower-hazard coating after assessment.Coatings engineer approves; stop on unknown chemistry.
Engineering / isolate and controlExtracted booth with verified clearance and safe air supply.Booth lead tests; stop on failed extraction or air.
Administrative / disciplineCOSHH assessment, cleaning, maintenance and access control.Supervisor inspects; hold on failed clearance.
PPE / PPETask-specific air-fed RPE and skin protection.Trainer checks; no spray if protection fails.

HSE five-level hierarchy complements ERICPD. For this spray process, the competent designer specifies the booth/extraction for the actual coating, spray load, workpiece geometry, mist generation, air supply and discharge. Competent commissioning verifies installed compatibility and effective exposure control under representative conditions and records performance benchmarks, acceptance, user instructions and maintenance duties before use; see HSE LEV commissioning. MR2 (January2025) supports measured/displayed clearance time, negative-pressure containment, breathing-air quality and equipment checks. Before each job, check extraction, airlines, RPE and damage; monitor booth condition and performance during use, and reassess process changes. Keep maintenance, clearance and examination results and act on defects. Stop failed extraction or unsafe air supply; correct the cause, recheck required performance and clearance, and authorise restart only when control is restored.

Verify before release

Use the evidence in a repair decision

Assess the actual cabin task, not just the bottle: product choice, ventilation and contact control must work together.

For this case, the observation is: A worker uses a solvent-based cleaner inside a vehicle with the doors nearly closed. Keep the observation distinct from an inferred cause. Vapour can build up; cleaning products may also damage skin and eyes. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

A stain remains. A worker proposes adding another cleaner to the bottle and closing the doors so it can soak in.

Open the interactive lesson and check →

Moving the extractor: reduce the handling demand

Judge the handling aid by the awkward work it removes, including the transfers needed to use it.

Two detailed views show a carpet-cleaning extractor with fluid tank, controls, hose and wheels. Left, the machine is confined between a car and stocked shelves with a narrow approach. Right, it is supported on a task-suitable handling platform along a clear route with a worker using the handle. Numbered leaders identify avoiding the awkward move, matching the aid and checking every transfer.

Understand the garage task

The valeter is lifting a full cleaning extractor while twisting between a car and stored supplies. The load includes its contents and may be awkward to grip; limited space prevents a comfortable approach or a clear step. This can strain the back, shoulders or other tissues. A stated machine weight or a lifting-technique course cannot establish that this particular move is safe for this worker.

Avoid the lift where reasonably practicable. Consider a suitable wheeled method, equipment position or a different servicing and emptying arrangement consistent with the manufacturer’s instructions. Where handling remains, assess the load, posture, frequency, route, environment and the worker’s needs together. A trolley only helps if it fits the space, supports the machine and can travel safely over the wet-bay route.

A worker in navy clothing seen from behind beside a separate enlarged side view of the lumbar spine and sacrum, with discs, yellow nerve roots and back muscle.View full detail ↗
The lower back: location and side view

The worker locates the lower back; the separate side view enlarges its bones, discs, nerve roots and nearby muscle.

Locate the lower back. How could the load, reach, route, equipment or work pattern be changed for the task in this lesson?

educational illustration · healthy anatomy; enlarged details and teaching colours.

What effective control looks like

How do TILE, TILEO and TILEE work in practice?

A TILE/TILEO/TILEE assessment should identify task, individual, load, environment and equipment or other factors before redesigning the work.

A facilities team moves archive boxes from a basement store to a first-floor office. Each box weighs 16 to 22 kg, some have poor handholds, the route includes a narrow door, a short ramp and a lift lobby, and the job is planned for two people over one afternoon. One worker is returning after a back-pain absence and the team has a trolley, but the trolley wheels catch on the ramp threshold. Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts

A poor assessment records 'two-person lift, use good manual-handling technique'. A better assessment uses TILE, TILEO and TILEE thinking to expose the real controls: reduce box weight, split contents, improve handles, use a route-selected handling aid, chosen only after confirming the intended lift/route, door and turning clearances, stability/capacity, thresholds, slope and starting/stopping forces suitable for the route, stage the work at waist height, repair the ramp threshold, plan rest/recovery, avoid twisting in the lift lobby and adapt duties for the returning worker without asking for unnecessary medical detail. Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts

Assessment factor What the assessment finds Redesign or control
Task Repeated lifting from floor, carrying through a narrow route and twisting in a lift lobby. Stage boxes on a trolley/lift table, reorient the route and reduce carry distance.Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts
Individual One worker is returning after back pain and may need temporary restriction. Private work-impact discussion, adjusted duties and review date.Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts
Load Boxes are heavy, variable, poorly gripped and not weight-marked. Split contents, mark weights, improve containers and keep heaviest items between knee and shoulder height.Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts
Environment Basement, ramp threshold, narrow door, lift lobby and time pressure create extra risk. Repair threshold, clear route, improve lighting and schedule the move over more time.Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts
Equipment/aids Trolley exists but is unsuitable for the route condition. Select suitable trolley, inspect wheels and confirm it can pass the full route.Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts
Other factors PPE, team handling, time pressure and communication affect the work. Brief roles, use commands and avoid team handling where mechanical aid can remove the lift.Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts
Ergonomics/existing controls Current storage and trolley arrangement still force bending, twisting and pushing over a poor threshold. Change storage height, repair the route and confirm controls work before the job continues.Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts
Recovery Continuous moving over one afternoon creates fatigue. Breaks, rotation, realistic pace and same-day review.Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts
Review Discomfort reports or route changes may alter risk. Supervisor observation and same-day review before continuing.Sources: HSE L23 Manual handling guidance on regulations; HSE Manual Handling Assessment Charts

Complete the route trial

Trial the aid over the whole intended route with worker feedback and record remaining manual transfers. If stairs are intended, introduce and assess that route explicitly before choosing stair equipment. Retain threshold repair and adjusted duties; possession of a trolley or a two-person lift does not close the assessment.

Verify before release

Use the evidence in a repair decision

Judge the handling aid by the awkward work it removes, including the transfers needed to use it.

For this case, the observation is: A worker lifts a full cleaning machine while twisted between a car and stored supplies. Keep the observation distinct from an inferred cause. An awkward load and restricted posture can cause musculoskeletal injury. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

A trolley is supplied, but the storage gap is too narrow and the worker still has to lift the full machine onto it sideways.

Open the interactive lesson and check →

Control rainwater before it becomes a walking hazard

A successful check shows a usable entrance during rain, not simply a warning sign or a dry photograph.

Perspective garage floor with a vehicle, wet patch, trailing hose and stored parts, contrasted with a clear walking route and a managed overhead supply. Callouts follow contamination, storage and hose routing.

Understand the garage task

Look at the entrance mat and the wet footprints extending into reception. The mat is both too ineffective to contain the incoming water and curled at an edge. Water can reduce the grip available on the smooth floor, while a moving or raised edge can catch a foot. Customers may carry bags, use mobility aids or look towards the service desk; the route cannot depend on everyone noticing the same defect.

Treat this as an entrance and cleaning design problem. First protect the contaminated route, remove water safely and correct the unstable mat. For lasting control, match matting, flooring and cleaning to the water brought in during actual wet weather. Cleaning must not create another open wet route. A cone communicates a warning but cannot dry the floor, flatten a mat or provide an accessible alternative path.

What effective control looks like

How can a wet entrance become a serious slip risk?

A public-facing entrance example shows why signs alone are rarely enough.

Wet leisure-centre entrance

Task material and setting: Wet entrance at a public leisure centre during heavy rain.

People and prerequisites: Reception staff, visitors and cleaner; relief route agreed

Before: Wet leaves and rainwater carried through an entrance onto a smooth floor; no mat change or drainage response.

During: Close or physically separate the wet route, give a safe alternative, remove contamination and inspect matting and drainage.

Hold or stop: Do not reopen while the floor remains wet or the alternate route creates another hazard.

Completion and hand back: Repair the recurrent water source, choose suitable matting/flooring, brief cleaners and reopen after a dry-floor check.

Evidence: Record weather trigger, barrier time, floor condition, repair owner, worker feedback and repeat incidents.

Riverside Leisure Ltd has a busy reception beside the pool corridor. On wet mornings, rain is walked through the entrance, pool users cross the route in flip-flops, and cleaners mop the tiled floor during customer arrivals. A cone is placed near the desk, but people still cross the wet surface because it is the main route.

A professional review would treat this as a route-design and contamination-control problem. It would improve entrance matting, drainage and cleaning timing, use barriers or route diversion while floors dry, check floor suitability, review footwear expectations for staff, increase inspection during peak wet periods and map near misses by location and time.

IssuePoor controlBetter control
Water walked inPut a wet-floor sign by reception.Improve matting, drainage and inspection frequency.
Cleaning during footfallMop quickly and hope people avoid it.Clean in sections, use barriers and leave floor dry.
Main route remains openExpect people to walk carefully.Divert pedestrians or create a dry route.
Repeated near missesTreat each as bad luck.Map location/time and fix root causes.
Mixed usersAssume staff controls cover customers.Consider children, older users, visitors and vulnerable service users.

The entrance sequence is a site illustration; HSE wet-floor access controls supports physical access prevention during wet cleaning.

Drying and inspection are handback checks for this entrance, not proof that every wet-process floor is safe. A kitchen or pool-side surface must be suitable for the actual activity and foreseeable contamination; competent assessment may be needed. The supervisor verifies controls at the route before reopening. HSE floor suitability.

Verify before release

Use the evidence in a repair decision

A successful check shows a usable entrance during rain, not simply a warning sign or a dry photograph.

For this case, the observation is: Wet footprints extend beyond a small curled entrance mat. Keep the observation distinct from an inferred cause. Water and a moving mat can cause a visitor or worker to slip or trip. Compare the controls in the guide with what is actually present, identify the unresolved gap and state who must resolve it before the task or route is released.

Fictional applied case

The floor is wet again ten minutes after cleaning. A supervisor suggests leaving a cone beside the counter for the winter.

Open the interactive lesson and check →

Capstone: decide whether the job may proceed

Combine the observations, restrictions and verification into one justified work decision.

Read the whole case before releasing a part

The valet team has finished a car, but a hose lies across the customer route and water remains at the doorway. A damaged extension connection is close to the washer. A worker proposes mixing two cleaners for the next cabin and carrying the heavy extractor around the barrier.

Protect the route, take defective electrical equipment out of use safely, retain the assessed cleaning method and arrange a suitable handling route before continuing.

Separate immediate protection from the investigation of causes. Use factual observations, the actual equipment and task information, and the appropriate competent roles. Where the evidence is missing, keep the affected operation restricted rather than treating uncertainty as permission.

Build the release evidence

Make the handover usable

State what may proceed, what remains held, who owns each unresolved issue and the evidence required to change the decision. Ask the next person to explain the restriction in their own words. Record a defined review point and communicate any change to affected colleagues, contractors and visitors. A form is useful only when it represents the actual arrangement.

Fictional applied case

The valet team has finished a car, but a hose lies across the customer route and water remains at the doorway. A damaged extension connection is close to the washer. A worker proposes mixing two cleaners for the next cabin and carrying the heavy extractor around the barrier.

Open the interactive lesson and check →

Take the learning into a real briefing

Turn the selected control into a clear question, observation and review trigger.

Prepare a short toolbox conversation

Choose one relevant task from this course. Describe its current scope, then ask a colleague to identify the people exposed and the control that must work. Avoid asking only whether everyone understands: a useful response explains the action and what would make the job stop.

Provide effective drainage, suitable surfaces, hose management and a cleaning routine matched to wet work.

For the fictional exercise below, write the observation, harm pathway, immediate protection, responsible role and evidence needed before release. Use the packaged worksheet; do not enter real personal or company information or submit an operational record.

Check the claim against the workplace

Follow up the change

Arrange a proportionate check after the control is used in representative conditions. If the observation contradicts the claimed protection, retain the restriction, report the discrepancy and revisit the assessment. Keep course completion separate from permission to perform specialist work.

Fictional applied case

The valet team has finished a car, but a hose lies across the customer route and water remains at the doorway. A damaged extension connection is close to the washer. A worker proposes mixing two cleaners for the next cabin and carrying the heavy extractor around the barrier.

Open the interactive lesson and check →