Full public teaching and readers are free without an account. A free learner account is required for saved LMS progress and recorded assessment. Completion and any course-completion certificate depend on the configured LMS conditions. Open the course overview.
Lesson 1
Start with identity and the actual use
Chemical hazard pictograms · examples and checksOptional reference · all nine symbols · does not change assessment requirements
READ THE LABEL · UNDERSTAND THE TASK
Recognise the symbol. Read the full label. Assess the actual task.
Examples illustrate possible uses of a symbol, not the classification of every formulation. A product can carry several pictograms. Check its current label, hazard statements and matching safety data sheet (SDS).
Warehouse storage: identify the product before judging compatibility, handling or spill arrangements.
CLP/GHS hazard pictograms: meanings and illustrative examples
Pictogram and hazard
What it can mean
Example and question before work
ExplosiveGHS01
Explosion, blast or projection hazards; also certain self-reactive substances and organic peroxides.
Example: Certain fireworks or reactive chemical products.Ask: Does the authorised task account for impact, heat and the product’s stability limits?
FlammableGHS02
Can ignite; also used for certain self-heating, pyrophoric or water-reactive hazards.
Example: Petrol or some solvent-based products.Ask: What could release vapour or ignite it during this task, including nearby work?
OxidisingGHS03
Can cause or intensify fire; some strong oxidisers present an explosion hazard.
Example: Oxygen or certain oxidising chemicals.Ask: What incompatible materials and contamination must the assessed storage and connection keep apart?
Gas under pressureGHS04
Pressurised gas may burst if heated; refrigerated gas can cause cold burns.
Example: Compressed-gas cylinders.Ask: Have the gas identity, cylinder, connection and pressure or temperature hazards been checked?
CorrosiveGHS05
May damage metals, cause severe skin burns or cause serious eye damage; read the stated hazard.
Example: Certain drain cleaners, acids or alkalis.Ask: Which contact and splash routes must be prevented in this actual handling or dilution task?
Acute toxicityGHS06
Can be toxic or fatal after short exposure through the stated route.
Example: Methanol or certain pesticide products.Ask: Which exposure routes and emergency arrangements does this product’s information identify?
Harmful / irritantGHS07
May indicate harmful acute toxicity, irritation, skin sensitisation, drowsiness or dizziness; also ozone-layer hazards.
Example: Some detergents or cleaning products.Ask: What do the hazard statements say? Do not dismiss this as a harmless or mild product.
Serious health hazardGHS08
Can indicate cancer, genetic or reproductive harm, organ damage, respiratory sensitisation or aspiration hazard.
Example: Petrol or some sensitising chemical products.Ask: Which particular health effect is stated, and how does the task prevent the relevant exposure?
Hazardous to the environmentGHS09
Hazardous to aquatic life, potentially with long-lasting effects.
Example: Certain pesticides, biocides or fuels.Ask: How will the assessed arrangements prevent release to drains, water or soil?
Read beyond the picture · Open a prompt to compare the explanation.
Is the exclamation mark the same as the chest-starburst symbol?
No. The two symbols communicate different groups of hazards. Read the actual hazard statements: skin sensitisation and respiratory sensitisation are not interchangeable, and neither symbol specifies the complete task controls.
Does a bottle with no pictogram prove the task is safe?
No. Work may generate hazardous dust, fume or mist, and exposure depends on the task. Resolve missing or conflicting identification before use. A pictogram is not a compatibility chart or a complete workplace risk assessment.
Which information turns recognition into a useful work decision?
Match the product and SDS revision. Read the hazard statements and relevant SDS sections for handling, storage, exposure control, emergencies and reactivity together. Then check the actual task assessment and controls. A safety data sheet is not itself a COSHH assessment.
Fisher Scientific UK · BP2618 range · CAS 67-63-0 Revision 19 · 13 October 2023
This learning example refers to the identified supplier edition. It is not a replacement SDS or confirmation that this is the latest sheet for a product you hold. Obtain the current matching supplier SDS before real use.
Below is SHARE’s learning annotation, not a rebranded supplier document or a complete safety data sheet.
Identity
Propan-2-ol / isopropanol; the referenced sheet identifies a laboratory-grade product.
Section 2 signals
Danger; flame and exclamation-mark pictograms. H225, H319 and H336 identify flammability, eye irritation and possible drowsiness/dizziness.
Section 3 composition
The referenced sheet lists isopropyl alcohol above 95% by weight.
Section 8 decision
Engineering measures and several glove-material options appear. Check the complete conditions; no single glove or respirator is selected by this lesson.
Section 9 example
A 12°C closed-cup flash point is listed. This is product data, not a workplace exposure reading or an automatic safe-temperature limit.
Explore every section
1. Identification
Match the product, supplier, intended use and emergency contact to the actual container. A familiar chemical name alone may not identify a formulation.
2. Hazards identification
Read classification, pictograms, signal word and hazard/precautionary statements together. Identify the routes and outcomes the task must prevent.
3. Composition / ingredients
Check concentration and relevant ingredients. A diluted mixture, hardener or changed formulation may need different information and assessment.
4. First-aid measures
Prepare product-specific first-aid arrangements and ready access to the full sheet. Do not replace the workplace emergency procedure with a memory exercise.
5. Firefighting measures
Provide the relevant information to the site fire-planning route. An SDS does not authorise an untrained worker to fight a chemical fire.
6. Accidental release
Plan who raises the alarm, isolates the area and deals with a spill within their training. Confirm available equipment and the boundary for specialist help.
7. Handling and storage
Translate the supplier conditions into the actual transfer, storage, access and housekeeping method. Consider other work and incompatible neighbours.
8. Exposure controls / PPE
Read exposure limits, engineering controls and residual PPE together. Check jurisdiction, units and averaging period. Verify control performance and exact glove/RPE suitability.
9. Physical / chemical properties
Consider volatility, flash point, state and other relevant properties at the actual temperature and method. Odour is not a reliable exposure measurement.
10. Stability / reactivity
Identify incompatible materials, conditions to avoid and possible decomposition. Check the whole process and waste stream, not just separate containers.
11. Toxicological information
Connect the health effects to possible inhalation, skin, eye and ingestion exposure. Use competent advice where specialist interpretation is needed.
12. Ecological information
Plan to prevent environmental release, including drains and water. Lack of a fish/tree symbol does not grant permission to discharge.
13. Disposal considerations
Specify the responsible waste route for the product, contaminated materials and containers. Do not assume evaporation or dilution is an acceptable disposal method.
14. Transport information
Check transport classification through the relevant competent route. Supply pictograms and transport labels have different functions.
15. Regulatory information
Identify relevant restrictions and market scope, then check workplace duties separately. A regulatory entry is not a completed COSHH assessment.
16. Other information
Check revision history, abbreviations and supporting statements. Trace material changes into the assessment, instructions, storage and briefing.
Worked COSHH application · fictional laboratory proposal
Define the proposed use
Fictional laboratory task: wipe small parts for 10 minutes twice per shift, using a proposed 50mL working quantity at ambient temperature. Record the exact product, method, location, people and frequency. These are exercise assumptions, not authorised operating limits.
Find the exposure and application differences
Compare a controlled dispensing/wiping proposal with spraying the same liquid over an open surface near other work. Spray, surface area, ventilation, duration, splashes and nearby people change the assessment even though the SDS is unchanged. Confirm the proposed use is suitable.
Work through the control hierarchy
First ask whether the task can avoid the chemical or use a verified safer method. If it remains necessary, assess release prevention, suitable dispensing, enclosure or ventilation before residual PPE. Do not invent a dilution or declare a small quantity safe.
Specify and verify the real controls
Use sections 7–10 together with competent task assessment. Identify ventilation performance, compatible equipment and the exact glove selection/breakthrough evidence for the job. Consider fire and explosion controls alongside health exposure. Do not copy a generic PPE line and call the work controlled.
Plan the whole job
Include setup, transfer, use, cleaning, storage, waste, maintenance and foreseeable upset. Identify who is exposed, who owns each action, training, first aid, spill arrangements and the separate emergency response boundary.
Record, brief and review
Record significant findings, remaining actions and evidence needed before release. Check controls in use. Reassess for changed product, concentration, quantity, temperature, spraying, location, equipment, symptoms, incidents or new supplier information.
Worked decision: HOLD the proposed task until the matching product/use information, exposure and ignition assessment, control verification and emergency arrangements are resolved by the responsible competent people. This learning example does not issue an operational assessment or authorise work.
Use identity, task and safety-data evidence without guessing a substance.
Start with identity and the actual use
A safety data sheet informs assessment, but it does not describe every workplace use. Establish the substance identity, quantity, physical form, release conditions, people and nearby processes. If identity is uncertain, do not experiment, mix or transfer it to find out.
Control incompatible storage, releases and inhalation exposure.
Follow the task through the area
Incompatible products share a bund
Two products with incompatible storage requirements have been put in one containment area.
An unlabelled decanted container
An unlabelled bottle is beside the cleaning station and a colleague wants to use it.
Dust escapes a damaged bag
A damaged powder bag is being emptied while local capture is ineffective.
Combustible dust settles near an ignition source
A known combustible powder has escaped and settled near equipment; compressed-air cleaning is suggested.
Compressed-gas cylinders left unsecured
Full and nominally empty gas cylinders have been left outside their planned storage arrangement. One is unsecured beside a trolley route, and its label has not been checked.
Challenge the first impression
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
What is chemical compatibility and inadvertent mixing?
Chemical compatibility is the safe relationship between substances, and inadvertent mixing is the accidental combination of substances that should have been kept apart.
Compatibility is not simply whether two products sit on the same shelf without reacting. It includes storage, handling, transfer, use, cleaning, waste disposal, drainage, emergency response and foreseeable abnormal situations such as leaks, wrong deliveries, overfills, rainwater ingress and equipment failure.
Inadvertent mixing can happen in ordinary workplaces: a cleaner mixes bleach and acid descaler, a worker pours waste into the wrong container, or a contractor uses an unapproved product in a drain. It can also happen in process industries: a road tanker connects to the wrong fill line, a transfer route is mis-valved, or incompatible waste is bulked in a tank.
The management task is to make the right action easier than the wrong one. That means clear naming, different connections, segregated storage, dedicated containers, locked or interlocked routes, independent verification and a culture where uncertainty stops the job.
Compatibility in plain English
Aspect
What it means
Why it matters
Storage compatibility
Whether substances can be stored near each other.
Prevents reaction if containers leak, break or spill.
Use compatibility
Whether substances can be used together or in the same process.
Prevents gas, heat, fire, overpressure or product instability.
Transfer compatibility
Whether the right substance reaches the right destination by the right route.
Prevents wrong-tank and wrong-line events.
Waste compatibility
Whether waste streams can be bulked or stored together.
Prevents drum explosions, toxic release and waste-treatment incidents.
Emergency compatibility
Whether response actions such as washing, dilution or absorbents are suitable.
Prevents responders worsening the reaction.
Applied case
An unlabelled container arrives with returns. Nearby extraction is unreliable, dust has accumulated and two cleaning products are being placed together.
Compare your decision
A safety data sheet informs assessment, but it does not describe every workplace use. Establish the substance identity, quantity, physical form, release conditions, people and nearby processes. If identity is uncertain, do not experiment, mix or transfer it to find out.
A safety data sheet informs assessment, but it does not describe every workplace use. Establish the substance identity, quantity, physical form, release conditions, people and nearby processes. If identity is uncertain, do not experiment, mix or transfer it to find out. Check the actual conditions and retain protection while gaps are resolved.
Lesson 2
Separate prevention, exposure control and response
Recognise incompatible mixing, failed extraction, combustible dust and cylinder hazards.
Separate prevention, exposure control and response
Storage compatibility, source control, containment, extraction, housekeeping and emergency arrangements address different parts of the pathway. Check that one intervention does not create another hazard, such as dispersing dust during unsuitable cleaning.
Control incompatible storage, releases and inhalation exposure.
Follow the task through the area
Incompatible products share a bund
Two products with incompatible storage requirements have been put in one containment area.
An unlabelled decanted container
An unlabelled bottle is beside the cleaning station and a colleague wants to use it.
Dust escapes a damaged bag
A damaged powder bag is being emptied while local capture is ineffective.
Combustible dust settles near an ignition source
A known combustible powder has escaped and settled near equipment; compressed-air cleaning is suggested.
Compressed-gas cylinders left unsecured
Full and nominally empty gas cylinders have been left outside their planned storage arrangement. One is unsecured beside a trolley route, and its label has not been checked.
Challenge the first impression
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
What are chemical classification, REACH, CLP and safety data sheets?
They are connected systems for identifying chemical hazards, communicating them and turning supply-chain information into workplace control.
Classification decides what hazards a substance or mixture has. CLP then communicates those hazards through labels, pictograms, signal words, hazard statements, precautionary statements and packaging requirements.
REACH sits across the chemical supply chain. It is concerned with registration, evaluation, authorisation and restriction, which means it can affect the information available, the uses allowed and whether safer alternatives should be considered.
Safety data sheets join supply information to workplace management. A good business does not simply file SDSs. It uses them to approve chemicals, update COSHH assessments, set storage rules, select controls, plan spills, train people and review whether the chemical is still the right choice.
Tells the assessor what kinds of harm to consider.
CLP
Communicates hazards through labels and packaging.
Helps users identify hazards quickly.
REACH
Manages registration, evaluation, authorisation and restriction.
Supports supply-chain control, substitution and legal use checks.
SDS
Provides structured hazard and safe-use information.
Feeds COSHH, storage, emergency and training decisions.
COSHH
Controls exposure at work.
Translates information into task-specific controls.
Applied case
An unlabelled container arrives with returns. Nearby extraction is unreliable, dust has accumulated and two cleaning products are being placed together.
Compare your decision
Storage compatibility, source control, containment, extraction, housekeeping and emergency arrangements address different parts of the pathway. Check that one intervention does not create another hazard, such as dispersing dust during unsuitable cleaning.
Storage compatibility, source control, containment, extraction, housekeeping and emergency arrangements address different parts of the pathway. Check that one intervention does not create another hazard, such as dispersing dust during unsuitable cleaning. Check the actual conditions and retain protection while gaps are resolved.
Lesson 3
Incompatible products share a bund
Stop the proposed handling, keep people clear and have a competent person verify identity and segregation; escalate any reaction through the emergency plan.
Read the scene evidence
Two products with incompatible storage requirements have been put in one containment area.
Identify the condition separately from the exposed person and any possible outcome.
How the harm pathway develops
Incompatible substances that can meet during a leak
Two products with incompatible storage requirements have been put in one containment area.
How people can be exposed
Leaks or improvised transfer allow the products to mix.
Possible harm
A harmful reaction releasing heat, gas or pressure.
Two products with incompatible storage requirements have been put in one containment area. The condition remains unresolved.
Protective response
Stop the proposed handling, keep people clear and have a competent person verify identity and segregation; escalate any reaction through the emergency plan.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Remove unnecessary incompatible materials from the process or store.
Substitution
Compare suitable less reactive alternatives after assessing their use and disposal.
Engineering controls
Provide compatible segregated storage and containment that prevents mixing.
Administrative controls
Verify identity, safety information, compatibility and controlled transfers.
PPE
Use assessed substance-specific residual protection; it does not prevent a reaction.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What is chemical compatibility and inadvertent mixing?
Chemical compatibility is the safe relationship between substances, and inadvertent mixing is the accidental combination of substances that should have been kept apart.
Compatibility is not simply whether two products sit on the same shelf without reacting. It includes storage, handling, transfer, use, cleaning, waste disposal, drainage, emergency response and foreseeable abnormal situations such as leaks, wrong deliveries, overfills, rainwater ingress and equipment failure.
Inadvertent mixing can happen in ordinary workplaces: a cleaner mixes bleach and acid descaler, a worker pours waste into the wrong container, or a contractor uses an unapproved product in a drain. It can also happen in process industries: a road tanker connects to the wrong fill line, a transfer route is mis-valved, or incompatible waste is bulked in a tank.
The management task is to make the right action easier than the wrong one. That means clear naming, different connections, segregated storage, dedicated containers, locked or interlocked routes, independent verification and a culture where uncertainty stops the job.
Compatibility in plain English
Aspect
What it means
Why it matters
Storage compatibility
Whether substances can be stored near each other.
Prevents reaction if containers leak, break or spill.
Use compatibility
Whether substances can be used together or in the same process.
Prevents gas, heat, fire, overpressure or product instability.
Transfer compatibility
Whether the right substance reaches the right destination by the right route.
Prevents wrong-tank and wrong-line events.
Waste compatibility
Whether waste streams can be bulked or stored together.
Prevents drum explosions, toxic release and waste-treatment incidents.
Emergency compatibility
Whether response actions such as washing, dilution or absorbents are suitable.
Prevents responders worsening the reaction.
Applied case
Two products with incompatible storage requirements have been put in one containment area. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 4
An unlabelled decanted container
Do not use, smell or mix the contents. Prevent access and have the designated person establish a safe identification and handling route.
Read the scene evidence
An unlabelled bottle is beside the cleaning station and a colleague wants to use it.
Identify the condition separately from the exposed person and any possible outcome.
How the harm pathway develops
Uncertain chemical identity and use information
An unlabelled bottle is beside the cleaning station and a colleague wants to use it.
How people can be exposed
A person uses or mixes an unidentified material without reliable task information.
Possible harm
Possible harmful exposure, reaction or unsuitable response.
An unlabelled bottle is beside the cleaning station and a colleague wants to use it. The condition remains unresolved.
Protective response
Do not use, smell or mix the contents. Prevent access and have the designated person establish a safe identification and handling route.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Eliminate unnecessary decanting by redesigning product supply at the task.
Substitution
Choose a suitable safer product and supply format after assessment.
Engineering controls
Provide secure, appropriate containers and dispensing arrangements.
Administrative controls
Maintain correct identity, labelling and accessible task-relevant safety information.
PPE
Select protection from reliable substance and task information; appearance is not enough.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What are chemical classification, REACH, CLP and safety data sheets?
They are connected systems for identifying chemical hazards, communicating them and turning supply-chain information into workplace control.
Classification decides what hazards a substance or mixture has. CLP then communicates those hazards through labels, pictograms, signal words, hazard statements, precautionary statements and packaging requirements.
REACH sits across the chemical supply chain. It is concerned with registration, evaluation, authorisation and restriction, which means it can affect the information available, the uses allowed and whether safer alternatives should be considered.
Safety data sheets join supply information to workplace management. A good business does not simply file SDSs. It uses them to approve chemicals, update COSHH assessments, set storage rules, select controls, plan spills, train people and review whether the chemical is still the right choice.
Tells the assessor what kinds of harm to consider.
CLP
Communicates hazards through labels and packaging.
Helps users identify hazards quickly.
REACH
Manages registration, evaluation, authorisation and restriction.
Supports supply-chain control, substitution and legal use checks.
SDS
Provides structured hazard and safe-use information.
Feeds COSHH, storage, emergency and training decisions.
COSHH
Controls exposure at work.
Translates information into task-specific controls.
Applied case
An unlabelled bottle is beside the cleaning station and a colleague wants to use it. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 5
Dust escapes a damaged bag
Stop the dust-generating task from a safe position, keep people clear and arrange competent substance-specific control.
Read the scene evidence
A damaged powder bag is being emptied while local capture is ineffective.
Identify the condition separately from the exposed person and any possible outcome.
A damaged powder bag is being emptied while local capture is ineffective. The condition remains unresolved.
Protective response
Stop the dust-generating task from a safe position, keep people clear and arrange competent substance-specific control.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Avoid open powder handling where a suitable closed supply method can remove the exposure.
Substitution
Compare a suitable lower-dust formulation after checking new risks.
Engineering controls
Contain the process and capture emissions at source with effective extraction.
Administrative controls
Identify the material, verify controls in use and manage cleaning and maintenance properly.
PPE
Select suitable respiratory and other protection for remaining exposure through the assessment.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What is COSHH and why does it matter?
COSHH means controlling substances hazardous to health so that work does not cause poisoning, dermatitis, asthma, cancer, lung disease, infection or other occupational ill health.
COSHH applies to many substances that are bought into a workplace, such as cleaning chemicals, paints, adhesives, solvents, fuels, disinfectants, laboratory reagents and process chemicals. It also applies to harmful substances created by the work itself, such as welding fume, wood dust, respirable crystalline silica, flour dust, solder fume, diesel exhaust emissions, metalworking fluid mist and biological agents.
The important point is that the label on a container is only the start. A substance with a modest hazard classification can become high risk if it is sprayed, heated, mixed, used in a confined area, handled for long periods or used by someone with existing sensitivity. Equally, a highly hazardous substance may be tightly controlled if it is enclosed, extracted, monitored and handled by competent people using a proven system.
COSHH management is therefore a chain of decisions: identify the substance, understand the form and route of exposure, decide who may be harmed, prevent exposure where reasonably practicable, control what remains, maintain the controls, train the people and check health or exposure where the risk justifies it.
How can the ISO 45001 hierarchy of controls guide COSHH exposure controls before relying on health surveillance?
Choose prevention and reliable engineering control before procedures or PPE; verify the actual equipment and task.
For isocyanate two-pack spray paint, assess a non-isocyanate coating or off-site process first. If spraying remains, use an enclosed extracted booth with clearance time and suitable air-fed breathing equipment, plus controlled gun cleaning, training and checks. The HSE spray-painter guide specifies these controls; HSENI COSHH sets the NI hierarchy. Stop spraying for failed extraction, unknown clearance time or missing air supply; do not rely on a better mask alone.
On a small screen, scroll this table sideways to read all columns.
How can the ERICPD hierarchy of controls guide COSHH exposure controls before relying on health surveillance?
ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
Worked activity: Task application for What should you know about COSHH control measures and health surveillance?
Activity and release context
For isocyanate two-pack spray paint, assess a non-isocyanate coating or off-site process first. If spraying remains, use an enclosed extracted booth with clearance time and suitable air-fed breathing equipment, plus controlled gun cleaning, training and checks. The HSE spray-painter guide specifies these controls; HSENI COSHH sets the NI hierarchy. Stop spraying for failed extraction, unknown clearance time or missing air supply; do not rely on a better mask alone.
Specify non-spray or off-site finished part if feasible.
Designer records option; hold spray if safe no-spray route works.
Substitute / reduce
Select compatible lower-hazard coating after assessment.
Coatings engineer approves; stop on unknown chemistry.
Engineering / isolate and control
Extracted booth with verified clearance and safe air supply.
Booth lead tests; stop on failed extraction or air.
Administrative / discipline
COSHH assessment, cleaning, maintenance and access control.
Supervisor inspects; hold on failed clearance.
PPE / PPE
Task-specific air-fed RPE and skin protection.
Trainer checks; no spray if protection fails.
How can the ISO 45001 hierarchy of controls guide COSHH exposure controls before relying on health surveillance?
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").
Worked activity: Task application for What should you know about COSHH control measures and health surveillance?
Activity and release context
For isocyanate two-pack spray paint, assess a non-isocyanate coating or off-site process first. If spraying remains, use an enclosed extracted booth with clearance time and suitable air-fed breathing equipment, plus controlled gun cleaning, training and checks. The HSE spray-painter guide specifies these controls; HSENI COSHH sets the NI hierarchy. Stop spraying for failed extraction, unknown clearance time or missing air supply; do not rely on a better mask alone.
Specify non-spray or off-site finished part if feasible.
Designer records option; hold spray if safe no-spray route works.
Substitute / reduce
Select compatible lower-hazard coating after assessment.
Coatings engineer approves; stop on unknown chemistry.
Engineering / isolate and control
Extracted booth with verified clearance and safe air supply.
Booth lead tests; stop on failed extraction or air.
Administrative / discipline
COSHH assessment, cleaning, maintenance and access control.
Supervisor inspects; hold on failed clearance.
PPE / PPE
Task-specific air-fed RPE and skin protection.
Trainer checks; no spray if protection fails.
HSE five-level hierarchy complements ERICPD. For this spray process, the competent designer specifies the booth/extraction for the actual coating, spray load, workpiece geometry, mist generation, air supply and discharge. Competent commissioning verifies installed compatibility and effective exposure control under representative conditions and records performance benchmarks, acceptance, user instructions and maintenance duties before use; see HSE LEV commissioning. MR2 (January2025) supports measured/displayed clearance time, negative-pressure containment, breathing-air quality and equipment checks. Before each job, check extraction, airlines, RPE and damage; monitor booth condition and performance during use, and reassess process changes. Keep maintenance, clearance and examination results and act on defects. Stop failed extraction or unsafe air supply; correct the cause, recheck required performance and clearance, and authorise restart only when control is restored.
Applied case
A damaged powder bag is being emptied while local capture is ineffective. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 6
Combustible dust settles near an ignition source
Hold the dust-generating and proposed cleaning work and have the competent team assess containment, ignition control and a suitable cleaning response.
Read the scene evidence
A known combustible powder has escaped and settled near equipment; compressed-air cleaning is suggested.
Identify the condition separately from the exposed person and any possible outcome.
How the harm pathway develops
Combustible dust layers and potential clouds at a handling process
A known combustible powder has escaped and settled near equipment; compressed-air cleaning is suggested.
How people can be exposed
Settled dust is dispersed and can meet an ignition source under suitable conditions.
Possible harm
A possible flash fire, explosion or secondary dust event.
A known combustible powder has escaped and settled near equipment; compressed-air cleaning is suggested. The condition remains unresolved.
Protective response
Hold the dust-generating and proposed cleaning work and have the competent team assess containment, ignition control and a suitable cleaning response.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Remove unnecessary combustible-powder handling through a suitable process redesign.
Substitution
Compare a suitable less dusty or non-combustible alternative with its full risks assessed.
Engineering controls
Provide suitable containment, capture, collection and explosion safeguards for the actual material and plant.
Administrative controls
Assess dust properties, ignition sources, layers, cleaning and change control through competent arrangements.
PPE
PPE cannot prevent a dust explosion or its escalation.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
What do dust explosion controls and housekeeping mean in practice?
They mean keeping combustible dust below dangerous conditions by controlling generation, spread, accumulation, ignition and escalation.
Combustible dust risk is easy to underestimate because the material may look ordinary. Flour, sugar, wood, grain, coal, plastic powder and some metal powders can be familiar materials during normal work. The hazard changes when they are finely divided, dispersed in air and mixed with oxygen. If an ignition source is present, the result can be a flash fire, local explosion, equipment rupture or building-wide secondary explosion.
Housekeeping is not simply cleaning for appearance. In dust explosion control it removes fuel, reveals abnormal leaks, prevents deposits building on high-level surfaces and reduces the chance that a small event becomes a catastrophic one. The cleaning standard should be written for the actual site: where dust lands, how fast it accumulates, which surfaces are difficult to reach, which cleaning tools are suitable and who checks that the work has been done.
Controls should be layered. Capture dust at source, keep process equipment sealed, extract and collect dust safely, prevent dust layers, classify hazardous areas where needed, remove ignition sources, manage hot work, maintain equipment and audit the system. One weak layer may be survivable; several weak layers in the same area can create a serious event. See HSE - Safe handling of combustible dusts HSG103.
Control areas and practical meaning - Control areas and practical meaning
Control area
Practical meaning
Poor practice to challenge
Dust containment
Keep dust inside equipment, ducting or closed transfer systems where reasonably practicable.
How can the ISO 45001 hierarchy of controls prevent combustible-dust explosions before relying on housekeeping?
The hierarchy should remove or reduce dust and ignition hazards before relying on rules or emergency response.
For dust explosions, engineered controls often carry the greatest weight: sealed transfer, effective extraction, correctly designed collectors, relief or suppression, rotary valves, earthing, monitoring, interlocks, suitable equipment and safe layout. Procedural controls still matter, but they should support the engineering basis rather than compensate for poor design.
The workshop decision transfers to flour bag tipping in food production and grain transfer in logistics: contain release, prevent deposits and ignition, verify collector protection and stop on leaks or alarms. The actual flour, grain or wood dust properties and plant geometry must be assessed; relief sizes and equipment certifications cannot be copied between sites.
The rotary-valve control in the table is only an explosion-isolation measure when its tested design, certification and condition make it suitable for the actual installation. An ordinary discharge valve is not assumed to provide this barrier.
PPE and RPE may control health exposure during cleaning, but they cannot protect a worker from the pressure and fire of a dust explosion. Plant integrity, prevention of dust clouds and ignition, and engineered mitigation carry the explosion risk decision.
Emergency response is a final layer. It should assume that responders may face smoke, fire, unstable structures, damaged plant, hidden dust layers, impaired visibility and possible secondary events. See HSE - Safe handling of combustible dusts HSG103.
How can the ERICPD hierarchy of controls prevent combustible-dust explosions before relying on housekeeping?
ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.
ERICPD for dust explosion controls - ERICPD for dust explosion controls
Control priority
Practical dust explosion controls
Evidence
HSE hierarchy level
Design and use for this task
Owner, checks, failure and stop
Eliminate
Avoid dusty transfer, buy liquid or pelletised forms, use pre-processed materials or remove redundant dusty plant.
Design review and procurement standard.
Elimination
Ask procurement whether pre-machined joinery parts can remove an in-house dry cutting step without shifting uncontrolled dust to another site. The manager verifies product quality and supplier controls.
Reduce quantities, transfer rates, drop heights, fines, dustiness and accumulation time.
Process review, cleaning frequency and inventory control.
Substitution / source reduction
Where machining remains, test whether a lower-fines feedstock or less dusty process is suitable for the product. A competent designer checks new material explosibility; no wood or metal powder is presumed non-combustible.
Enclose dusty processes, segregate dust-handling rooms and locate high-risk plant outside where suitable.
Layout drawings, access controls and DSEAR review.
Engineering separation
Enclose dusty transfer and locate/segregate collectors and occupied areas as the design permits. Barriers must also consider flame and pressure paths, not only visible dust spread.
Use capture, ventilation, safe collectors, explosion relief, ignition control, hot-work permits and monitoring.
Inspection records, equipment tests and permit evidence.
Engineering prevention and mitigation plus administrative control
Specify capture, earthing, ignition control, suitable electrical equipment, collector relief/isolation and interlocks for the tested dust and zone. Commission against design conditions; operators check alarms and pressure before use, with permits governing intrusive work.
Use RPE and PPE for health exposure or cleaning residual dust, selected for the task.
RPE selection, face-fit records and training.
PPE for residual health exposure only
Choose compatible RPE and protective clothing for cleaning exposure, fit-test tight-fitting RPE, maintain and replace it. No personal equipment makes a dust cloud, ignition source or unprotected collector acceptable.
Train people, supervise cleaning, investigate deposits and manage change.
Training records, audits, action close-out and leadership review.
Administrative assurance, not a substitute
Assign cleaning zones including high beams, inspect deposition and alarms, investigate leaks, maintain collectors and review changes. The manager funds repair and confirms a documented hand-back.
How can the ISO 45001 hierarchy of controls prevent combustible-dust explosions before relying on housekeeping?
The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").
ERICPD for dust explosion controls - ERICPD for dust explosion controls
Control priority
Practical dust explosion controls
Evidence
HSE hierarchy level
Design and use for this task
Owner, checks, failure and stop
Eliminate
Avoid dusty transfer, buy liquid or pelletised forms, use pre-processed materials or remove redundant dusty plant.
Design review and procurement standard.
Elimination
Ask procurement whether pre-machined joinery parts can remove an in-house dry cutting step without shifting uncontrolled dust to another site. The manager verifies product quality and supplier controls.
Reduce quantities, transfer rates, drop heights, fines, dustiness and accumulation time.
Process review, cleaning frequency and inventory control.
Substitution / source reduction
Where machining remains, test whether a lower-fines feedstock or less dusty process is suitable for the product. A competent designer checks new material explosibility; no wood or metal powder is presumed non-combustible.
Enclose dusty processes, segregate dust-handling rooms and locate high-risk plant outside where suitable.
Layout drawings, access controls and DSEAR review.
Engineering separation
Enclose dusty transfer and locate/segregate collectors and occupied areas as the design permits. Barriers must also consider flame and pressure paths, not only visible dust spread.
Use capture, ventilation, safe collectors, explosion relief, ignition control, hot-work permits and monitoring.
Inspection records, equipment tests and permit evidence.
Engineering prevention and mitigation plus administrative control
Specify capture, earthing, ignition control, suitable electrical equipment, collector relief/isolation and interlocks for the tested dust and zone. Commission against design conditions; operators check alarms and pressure before use, with permits governing intrusive work.
Use RPE and PPE for health exposure or cleaning residual dust, selected for the task.
RPE selection, face-fit records and training.
PPE for residual health exposure only
Choose compatible RPE and protective clothing for cleaning exposure, fit-test tight-fitting RPE, maintain and replace it. No personal equipment makes a dust cloud, ignition source or unprotected collector acceptable.
Train people, supervise cleaning, investigate deposits and manage change.
Training records, audits, action close-out and leadership review.
Administrative assurance, not a substitute
Assign cleaning zones including high beams, inspect deposition and alarms, investigate leaks, maintain collectors and review changes. The manager funds repair and confirms a documented hand-back.
A known combustible powder has escaped and settled near equipment; compressed-air cleaning is suggested. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 7
Compressed-gas cylinders left unsecured
Keep people and traffic clear and report the storage failure. Arrange identification and safe handling by trained people using supplier instructions; do not improvise a move or approach a suspected leaking or heated cylinder.
Read the scene evidence
Full and nominally empty gas cylinders have been left outside their planned storage arrangement. One is unsecured beside a trolley route, and its label has not been checked.
Identify the condition separately from the exposed person and any possible outcome.
How the harm pathway develops
Unsecured compressed-gas cylinders are left exposed to vehicle impact beside a store route.
Full and nominally empty gas cylinders have been left outside their planned storage arrangement. One is unsecured beside a trolley route, and its label has not been checked.
How people can be exposed
A cylinder can fall or be struck; a damaged valve or connection may release stored gas.
Possible harm
Falling cylinders and pressure release can injure people. Fire, oxygen displacement or enhanced burning depend on the actual gas.
Full and nominally empty gas cylinders have been left outside their planned storage arrangement. One is unsecured beside a trolley route, and its label has not been checked. The condition remains unresolved.
Protective response
Keep people and traffic clear and report the storage failure. Arrange identification and safe handling by trained people using supplier instructions; do not improvise a move or approach a suspected leaking or heated cylinder.
Select controls by how they prevent harm
Immediate protection and longer-term changes have different purposes. Explore each level and check what is feasible for the actual site, task and people.
Use the five-level hierarchy below. Inspection, instruction and supervision sustain every chosen control; they do not replace physical prevention.
Control level
Application to this case
Elimination
Remove unnecessary cylinder stock from the workplace through a planned supplier return.
Substitution
Consider a suitable process that avoids this gas supply, with the alternative risks assessed.
Engineering controls
Provide designed restraint, impact protection and a suitably ventilated, compatible storage arrangement for the identified gases.
Administrative controls
Control full and empty cylinders, labels, inventories, handling equipment and emergency arrangements with the supplier.
PPE
Use assessed protection for authorised handling; PPE cannot secure a cylinder or make a gas release safe.
Verify, communicate and hand back
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Explain the task-specific evidence, who must act and what restriction remains until it is resolved. A closed action or a course badge cannot establish a live site condition.
How do LPG and welding cylinders change the controls?
Use a planned storage and handling arrangement for the actual gas, cylinder and site. Keep cylinders secure and protected, use compatible regulators and hoses, and agree the supplier’s emergency route.
LPG cylinder and bulk-tank locations need competent siting assessment, including ignition, traffic impact, access, ventilation and low points where vapour could collect. Keep cylinders in their prescribed orientation and move them with suitable equipment. Full and nominally empty cylinders both need control; an empty cylinder can retain hazardous contents. Do not improvise adapters, repair valves or use a flame to find a leak.
Portable oxy-fuel equipment needs the right gas, regulators, hose assemblies, non-return valves and flashback arresters. A non-return valve limits reverse flow; it does not stop a flame front. HSE INDG297 calls for arresters on both oxygen and fuel-gas lines near the regulators, with additional protection for long hose arrangements. Select and maintain the complete assembly with the supplier, and keep oil and grease away from oxygen equipment. HSE INDG297 Gas welding cutting and similar processes.
Hot work also needs control of nearby combustibles, hidden voids, fumes, other workers and post-work fire risk. The permit and risk assessment set the task-specific monitoring and fire-watch arrangements; this page does not prescribe an arbitrary duration. Stop for unknown coatings, residues, containers or gas identity and obtain competent assessment. A cylinder involved in fire, or an acetylene cylinder becoming hot or vibrating, requires withdrawal and emergency fire-service help, not an improvised cooling or moving operation.
For welding-fume control, use HSE welding fume: protect workers alongside the actual task assessment; older hot-work publications do not replace current fume advice.
How should gas risks be reduced?
First ask whether the gas or hot-work task can be removed. Where it remains, reduce the potential release, contain and isolate the supply, control ignition and combustion, and plan for failure before relying on instructions or PPE.
For a temporary event, a suitable electric cooking option may remove the need for LPG cylinders and hoses, although electrical capacity and other hazards still need checking. For fabrication, a cold-cutting method may avoid oxy-fuel hot work. If gas is necessary, competent design and installation should provide appropriate containment, ventilation, flues, isolation and protective devices.
Keep quantities proportionate to the work, protect pipework and cylinders from vehicles and heat, and control ignition sources where a release could create an explosive atmosphere. Establish who owns ventilation and safety interlocks, and how faults are reported and repaired. Never defeat an interlock to keep production running. DSEAR assessment determines prevention and mitigation measures; a generic separation distance or gas alarm setpoint is not a substitute. HSE Dangerous Substances and Explosive Atmospheres Regulations.
Administrative controls then support the engineered precautions: authorise work, coordinate contractors, check changes, maintain the system and practise evacuation. Use suitable eye, hand, body and other protection for identified residual hazards such as hot work or cylinder handling. Ordinary masks and gloves cannot make an unsafe gas atmosphere acceptable. Escape, emergency intervention and confined-space rescue need separately planned competent arrangements.
Applied case
Full and nominally empty gas cylinders have been left outside their planned storage arrangement. One is unsecured beside a trolley route, and its label has not been checked. At handover, someone says that assigning an action owner is enough to restart. Decide what is still needed.
Compare your decision
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action.
Name who owns the work, verify implementation and check effectiveness in real conditions. A learning result or request for control does not close an operational action. Ownership and training support the control but do not demonstrate its effectiveness.
Lesson 8
Shift handover: connect the hazards
Defend the stopping condition and the evidence needed for release.
Reconstruct the whole task
An unlabelled container arrives with returns. Nearby extraction is unreliable, dust has accumulated and two cleaning products are being placed together.
The label has been rewritten from memory and the extraction fan makes a noise, but nobody has confirmed the substance or effective capture at the task.
Keep the task restricted until substance identity and the relevant control performance are confirmed by the designated competent people.
Build an evidence-led handover
Item
What the receiver needs
Task and location
Chemical storage, dust and exposure controls — identify the affected people and boundaries.
Actual condition
The label has been rewritten from memory and the extraction fan makes a noise, but nobody has confirmed the substance or effective capture at the task.
Control and current restriction
Keep the task restricted until substance identity and the relevant control performance are confirmed by the designated competent people.
Verification and owner
Name the responsible role and the task-specific evidence. Keep unresolved matters open.
Use the documents as working tools
Map the task, people, exposure pathway, existing controls, missing evidence and review trigger. Use the fictional course case.
Prepare a five-minute task briefing. Ask a scenario question and check understanding, rather than relying on an attendance signature.
Find who owns the control, who can authorise release and how a worker escalates a defect. Check the actual local arrangements.
Compare a claim with an observation, a relevant record and a competent explanation. Record open actions and verify closure.
How do LPG and welding cylinders change the controls?
Use a planned storage and handling arrangement for the actual gas, cylinder and site. Keep cylinders secure and protected, use compatible regulators and hoses, and agree the supplier’s emergency route.
LPG cylinder and bulk-tank locations need competent siting assessment, including ignition, traffic impact, access, ventilation and low points where vapour could collect. Keep cylinders in their prescribed orientation and move them with suitable equipment. Full and nominally empty cylinders both need control; an empty cylinder can retain hazardous contents. Do not improvise adapters, repair valves or use a flame to find a leak.
Portable oxy-fuel equipment needs the right gas, regulators, hose assemblies, non-return valves and flashback arresters. A non-return valve limits reverse flow; it does not stop a flame front. HSE INDG297 calls for arresters on both oxygen and fuel-gas lines near the regulators, with additional protection for long hose arrangements. Select and maintain the complete assembly with the supplier, and keep oil and grease away from oxygen equipment. HSE INDG297 Gas welding cutting and similar processes.
Hot work also needs control of nearby combustibles, hidden voids, fumes, other workers and post-work fire risk. The permit and risk assessment set the task-specific monitoring and fire-watch arrangements; this page does not prescribe an arbitrary duration. Stop for unknown coatings, residues, containers or gas identity and obtain competent assessment. A cylinder involved in fire, or an acetylene cylinder becoming hot or vibrating, requires withdrawal and emergency fire-service help, not an improvised cooling or moving operation.
For welding-fume control, use HSE welding fume: protect workers alongside the actual task assessment; older hot-work publications do not replace current fume advice.
Applied case
The label has been rewritten from memory and the extraction fan makes a noise, but nobody has confirmed the substance or effective capture at the task.
Compare your decision
Keep the task restricted until substance identity and the relevant control performance are confirmed by the designated competent people.
Keep the task restricted until substance identity and the relevant control performance are confirmed by the designated competent people.
Lesson 9
Your workplace transfer challenge
Turn one lesson into a bounded check with an owner and a review trigger.
Prepare a useful task briefing
Control incompatible storage, releases and inhalation exposure.
Use the printable course workbook to describe one fictional task. State who could be exposed, the harmful mechanism, a higher-level control, the immediate restriction and the evidence needed to close the action.
Test understanding and inspect the arrangement
Maintain restrictions until the substance-specific controls and response are confirmed.
Ask the team what they would do if the control failed. Compare their answer with the actual arrangements and the source teaching. Check both what people understand and whether the physical control works.
Keep learning and operational authority clear
Independent warehouse awareness and decision practice for a GB baseline; check corresponding Northern Ireland duties and site arrangements. Completion is not practical competence, a licence or authority for specialist work.
The workbook is a practice document. Use the authorised workplace system for real risk assessments, permits, defect reports and audits. Video demonstrations can be added later; no missing video is required to complete this course.
Applied case
You are asked to prepare a toolbox talk and a check for the next shift. The current document says only: be more careful.
Compare your decision
Identify the task, responsible role, required evidence, restriction and trigger for review.
A useful action connects the work to its owner, evidence and a clear decision boundary.
Match the nine hazard symbols
End-of-course revision · Drag each symbol to its hazard name, or use the menu on each card with touch or keyboard. This is practice alongside the separate final assessment.
Acute toxicity
Corrosive
Explosive
Flammable
Gas under pressure
Harmful / irritant
Hazardous to the environment
Oxidising
Serious health hazard
Match all nine symbols, then check your choices.
Need the reference table?Chemical hazard pictograms · examples and checksOptional reference · all nine symbols · does not change assessment requirements
READ THE LABEL · UNDERSTAND THE TASK
Recognise the symbol. Read the full label. Assess the actual task.
Examples illustrate possible uses of a symbol, not the classification of every formulation. A product can carry several pictograms. Check its current label, hazard statements and matching safety data sheet (SDS).
CLP/GHS hazard pictograms: meanings and illustrative examples
Pictogram and hazard
What it can mean
Example and question before work
ExplosiveGHS01
Explosion, blast or projection hazards; also certain self-reactive substances and organic peroxides.
Example: Certain fireworks or reactive chemical products.Ask: Does the authorised task account for impact, heat and the product’s stability limits?
FlammableGHS02
Can ignite; also used for certain self-heating, pyrophoric or water-reactive hazards.
Example: Petrol or some solvent-based products.Ask: What could release vapour or ignite it during this task, including nearby work?
OxidisingGHS03
Can cause or intensify fire; some strong oxidisers present an explosion hazard.
Example: Oxygen or certain oxidising chemicals.Ask: What incompatible materials and contamination must the assessed storage and connection keep apart?
Gas under pressureGHS04
Pressurised gas may burst if heated; refrigerated gas can cause cold burns.
Example: Compressed-gas cylinders.Ask: Have the gas identity, cylinder, connection and pressure or temperature hazards been checked?
CorrosiveGHS05
May damage metals, cause severe skin burns or cause serious eye damage; read the stated hazard.
Example: Certain drain cleaners, acids or alkalis.Ask: Which contact and splash routes must be prevented in this actual handling or dilution task?
Acute toxicityGHS06
Can be toxic or fatal after short exposure through the stated route.
Example: Methanol or certain pesticide products.Ask: Which exposure routes and emergency arrangements does this product’s information identify?
Harmful / irritantGHS07
May indicate harmful acute toxicity, irritation, skin sensitisation, drowsiness or dizziness; also ozone-layer hazards.
Example: Some detergents or cleaning products.Ask: What do the hazard statements say? Do not dismiss this as a harmless or mild product.
Serious health hazardGHS08
Can indicate cancer, genetic or reproductive harm, organ damage, respiratory sensitisation or aspiration hazard.
Example: Petrol or some sensitising chemical products.Ask: Which particular health effect is stated, and how does the task prevent the relevant exposure?
Hazardous to the environmentGHS09
Hazardous to aquatic life, potentially with long-lasting effects.
Example: Certain pesticides, biocides or fuels.Ask: How will the assessed arrangements prevent release to drains, water or soil?
Read beyond the picture · Open a prompt to compare the explanation.
Is the exclamation mark the same as the chest-starburst symbol?
No. The two symbols communicate different groups of hazards. Read the actual hazard statements: skin sensitisation and respiratory sensitisation are not interchangeable, and neither symbol specifies the complete task controls.
Does a bottle with no pictogram prove the task is safe?
No. Work may generate hazardous dust, fume or mist, and exposure depends on the task. Resolve missing or conflicting identification before use. A pictogram is not a compatibility chart or a complete workplace risk assessment.
Which information turns recognition into a useful work decision?
Match the product and SDS revision. Read the hazard statements and relevant SDS sections for handling, storage, exposure control, emergencies and reactivity together. Then check the actual task assessment and controls. A safety data sheet is not itself a COSHH assessment.