Construction traffic and mobile plant · learning reader

Free training · Approx. 2h–3h · estimated self-paced learning, including activities and assessment.

Public teaching is free without an account. A free learner account is required for confirmed LMS assessment, completion and certificate records. See the full course outline and access routes.

Teaching and applied cases for accessible study. The interactive course records assessed completion.

Lesson 1

Map the whole movement system

Vehicle risk follows the whole journey and task. Boundaries and interfaces are often where the plan fails.

How should a traffic management plan be built?

Build a site-specific plan from observed routes, vehicle envelopes, people, activities, controls, owners and change triggers; check it in the field before movement.

Sketch arrival, parking, unloading, pedestrian desire lines, crossings, welfare, work zones and emergency access. Test the largest intended vehicle and load, including turning, swept path, clearance, visibility and surface. Use a competent designer where geometry or public interface is complex; no universal site speed or barrier specification is supplied here.

Agree who owns gates, bookings, barriers, driver briefings, vehicle checks, temporary changes and inspection. Keep the plan where users can act on it. Stop and revise when the real route differs from the drawing.

Plan elementQuestions to answerTypical evidence
Movement and peopleWho arrives, walks, cycles, loads, reverses or may cross?Observed movement map and consultation.
Layout and plantCan the intended vehicle, load and people move with separation and clearance?Competent layout and vehicle check.
Operating controlsWho controls booking, gate, crossing, speed, unloading and emergencies?Named owners and communicated rules.
Change and assuranceWhat triggers a hold, revision and authorised restart?Field check, defect record and hand-back.
Road boundaryCould works affect a public road, footway, cycleway or sightline?Authority consultation and approved competent scheme where required.

Visual practice · Map the whole movement system

Workers on a protected walkway separated by continuous guardrails from a site dumper on a UK construction site
SHAREhub photographic illustration · Workers on a protected walkway separated by continuous guardrails from a site dumper on a UK construction site. Use the written case for the exercise; this image does not prove a defect or safe system.
How should a traffic management plan be built?

Build a site-specific plan from observed routes, vehicle envelopes, people, activities, controls, owners and change triggers; check it in the field before movement. Sketch arrival, parking, unloading, pedestrian desire lines, crossings, welfare, work zones and emergency access. Test the largest intended vehicle and load, including turning, swept path, clearance, visibility and surface. Use a competent designer where geometry or public interface is complex; no universal site speed or barrier specification is supplied here.

What should a practical traffic layout model include?

A useful layout drawing shows both normal and changed routes, the people exposed and the clearance needed by the actual vehicle; it is checked on site. Show separate pedestrian and vehicle entry, direct walkways, controlled crossings, loading and turning space, parking, visibility, lighting, gradients, overhead services and emergency access. Recheck the plan when scaffolds, hoarding, road plates, excavations or welfare routes change; temporary works can create new vehicle-pedestrian interfaces. Check the path people actually choose, including disabled access and visiting drivers.

How harm develops in the linked model

The public may be struck, trapped or forced into the road; visitors may not understand the site traffic system.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What should a practical traffic layout model include?

A useful layout drawing shows both normal and changed routes, the people exposed and the clearance needed by the actual vehicle; it is checked on site.

Show separate pedestrian and vehicle entry, direct walkways, controlled crossings, loading and turning space, parking, visibility, lighting, gradients, overhead services and emergency access. Recheck the plan when scaffolds, hoarding, road plates, excavations or welfare routes change; temporary works can create new vehicle-pedestrian interfaces. Check the path people actually choose, including disabled access and visiting drivers. Barriers must suit the site risk rather than merely look robust.

A drawing is a communication tool, not proof of safety. The route must be walked and driven under representative conditions and changed after a near miss, altered phase, new vehicle or failed control.

Layout elementWhat to examineGood control
Pedestrian routeDoes it remain direct, accessible and clear during deliveries?Separate or protected route and crossing.
Vehicle routeCan the actual vehicle turn and stop with clearance?Competent swept-path and field check.
Loading areaCan the driver and loaders work without entering moving traffic?Controlled bay and vehicle restraint or other site-suitable controls.
Public boundaryCan a vehicle or load intrude into public space?Secure boundary and authority interface where applicable.
Emergency accessCan responders reach the site if a delivery is waiting?Unobstructed route and tested access plan.

Apply the learning

The route review covers the site yard but ends at a busy public footpath.

Decision and explanation

Include public interfaces, access, unloading, travel and changing work areas in the movement plan.

Vehicle risk follows the whole journey and task. Boundaries and interfaces are often where the plan fails.

Lesson 2

Plan roles and communicate limits

Driver competence and site-specific information are both needed; unfamiliarity with local routes can defeat an otherwise sound plan.

Who needs to understand mobile plant and vehicles?

Workers and operators use the stop route; supervisors control interfaces; managers own resources and verification; specialists advise within competence.

Role and decision
Role Decision Practical proof
Operator Check machine, route, visibility and ground before movement. Show a safe stop and defect quarantine.Sources: HSE introduction to workplace transport safety; HSENI workplace transport; HSE mobile work equipment
Supervisor Separate pedestrians, delivery drivers and moving plant. Walk the current traffic route and crossing.Sources: HSE introduction to workplace transport safety; HSENI workplace transport; HSE mobile work equipment
Site manager Plan construction phases, route changes and lifting interfaces. Approved traffic plan and change briefing.Sources: HSE introduction to workplace transport safety; HSENI workplace transport; HSE mobile work equipment
Specialist Assess rollover, restraint, stability and lifting scope. Equipment/task-specific decision record.Sources: HSE introduction to workplace transport safety; HSENI workplace transport; HSE mobile work equipment

Visual practice · Plan roles and communicate limits

Actual SHAREsimulate construction model context: The notice board has yesterday’s site route
Actual SHAREsimulate model capture · The notice board has yesterday’s site route. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Investigate 1: Site information board

The board is visible, but its presence cannot establish that the information is current or readable at the workface. The case says yesterday’s route is displayed: ask who owns the update and how people will receive it.

Investigate 2: Marked pedestrian route

A coloured route crosses the model. Compare today’s delivery zone with the stated pedestrian arrangement; a painted or modelled line cannot by itself prevent a vehicle conflict.

Investigate 3: Entry and briefing area

The entrance area contains information and route cues. Consider how a visitor receives the current route and emergency instructions before entering the work area.

Who needs to understand mobile plant and vehicles?

Workers and operators use the stop route; supervisors control interfaces; managers own resources and verification; specialists advise within competence.

How should a changing construction site manage a dumper?

Plan pedestrian and dumper routes for each construction phase, then stop and revise them when the workface or deliveries change. At fictional BuildOut Ltd, a site dumper is delivering fill beside a changing pedestrian path. A new trade opens a shortcut across the reversing zone while temporary lighting is poor. The supervisor stops dumper movement, directs people to a protected route, checks turning and ground conditions, and updates the traffic plan before restarting.

How harm develops in the linked model

Signs and inductions lose value when the changing site no longer matches them; language, literacy and access needs can be missed.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How can this guidance help in practice?

Workers and people carrying out the task
Use the Mobile plant and vehicles guidance to recognise relevant hazards, understand the precautions and identify when to stop, report a problem or ask for competent support.
Supervisors and managers
Use the task examples and control checks to plan work, brief the team, check implementation and assign improvements with owners and follow-up.
Safety, health, risk and assurance professionals
Use the explanations, sources and operational examples to develop assessments, audits and control verification. Check the actual scope and jurisdiction before applying a duty.
Learners, trainers and organisational decision makers
Use the definitions and examples to connect theory with workplace decisions, build briefings and ask informed questions. This page does not certify competence or authorise work.

How should a changing construction site manage a dumper?

Plan pedestrian and dumper routes for each construction phase, then stop and revise them when the workface or deliveries change.

At fictional BuildOut Ltd, a site dumper is delivering fill beside a changing pedestrian path. A new trade opens a shortcut across the reversing zone while temporary lighting is poor. The supervisor stops dumper movement, directs people to a protected route, checks turning and ground conditions, and updates the traffic plan before restarting. A banksman or warning alarm supports a designed route; neither replaces physical separation where feasible. The manager briefs subcontractors and verifies the new route during the next delivery. Sources: HSE construction site traffic management, HSE introduction to workplace transport safety, HSENI workplace transport.

Apply the learning

A subcontract delivery driver arrives without the current route and unloading instructions.

Decision and explanation

Hold entry until the driver understands the safe route, restrictions and contact arrangements.

Driver competence and site-specific information are both needed; unfamiliarity with local routes can defeat an otherwise sound plan.

Lesson 3

Protect people outside the boundary

People outside the site have no duty to understand its vehicle system. Plan the crossing and maintain a safe route.

When does a public road or footway need a separate traffic scheme?

Before work occupies or changes a public road, footway or cycleway, use a competent design and the relevant GB highway or NI roads authority route.

Road or footway taskBefore installationLive hold pointCompletion and evidence
Works vehicle crosses a public footway at a site gate.Assess pedestrians, cyclists, visibility and vehicle timing; agree any interface measures with the relevant authority.Hold if sightline, accessible route or public protection is lost.Restore public access and record inspection and hand-back.
Temporary footway occupation for construction delivery.Competent person determines permissions, accessible alternative, barriers and signing under local authority conditions.Do not occupy or divert without the applicable approval; inspect after changes.Remove controls in planned order, reinstate and notify authority as required.
Street works or roadworks with traffic control.Use applicable GB DfT or NI DfI code, Chapter 8 where relevant, road authority approval and competent team.Stop if scheme differs from approved design, signs fail or public users cannot pass safely.Inspect, remove, reinstate and retain scheme, approval and hand-back records.

Visual practice · Protect people outside the boundary

Workers on a protected walkway separated by continuous guardrails from a site dumper on a UK construction site
SHAREhub photographic illustration · Workers on a protected walkway separated by continuous guardrails from a site dumper on a UK construction site. Use the written case for the exercise; this image does not prove a defect or safe system.
When does a public road or footway need a separate traffic scheme?

Before work occupies or changes a public road, footway or cycleway, use a competent design and the relevant GB highway or NI roads authority route.

How does traffic risk change on a live construction site?

On a live construction project, stop a delivery when the temporary pedestrian route is blocked; restore separation and re-authorise the route before unloading. BuildOut Ltd is a fictional leisure-centre refurbishment. A telehandler and HGV deliver palletised material while workers use welfare and visitors use a temporary entrance. Rain, stored materials and a moved barrier narrow the pedestrian route.

How harm develops in the linked model

The public may be struck, trapped or forced into the road; visitors may not understand the site traffic system.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How does traffic risk change on a live construction site?

On a live construction project, stop a delivery when the temporary pedestrian route is blocked; restore separation and re-authorise the route before unloading.

BuildOut Ltd is a fictional leisure-centre refurbishment. A telehandler and HGV deliver palletised material while workers use welfare and visitors use a temporary entrance. Rain, stored materials and a moved barrier narrow the pedestrian route. The supervisor checks the route, ground, load, visibility and public boundary before admitting the vehicle; the driver and operator need site-specific instructions.

If the walkway is blocked or the agreed unloading area is unavailable, hold the vehicle at a safe waiting point. Clear or redesign the route, coordinate contractors, brief everyone affected and verify separation before work resumes. After unloading, restore barriers and access, inspect the area and record the changed plan. This is an example, not a certified layout.

IssueWeak responseStronger response
Rain and soft groundKeep timetable and assume plant can use the original route.Check support and traction; hold until the route is suitable.
Barrier moved for palletsAsk pedestrians to take care.Restore a suitable protected route or redesign delivery.
Unbriefed HGV driverWave driver through the gate.Hold at a safe waiting point and brief the route and stop point.
Visitor entrance near plantRely on high-visibility clothing and warnings.Physically protect visitor route and check public interface.

Apply the learning

A delivery needs to cross an occupied pavement while children are passing.

Decision and explanation

Stop the movement and apply the agreed controlled public-interface arrangement.

People outside the site have no duty to understand its vehicle system. Plan the crossing and maintain a safe route.

Lesson 4

Design separation that survives the shift

A route must remain physically usable; a drawn line or signed plan does not protect people when the route is blocked.

What should a practical traffic layout model include?

A useful layout drawing shows both normal and changed routes, the people exposed and the clearance needed by the actual vehicle; it is checked on site.

Show separate pedestrian and vehicle entry, direct walkways, controlled crossings, loading and turning space, parking, visibility, lighting, gradients, overhead services and emergency access. Recheck the plan when scaffolds, hoarding, road plates, excavations or welfare routes change; temporary works can create new vehicle-pedestrian interfaces. Check the path people actually choose, including disabled access and visiting drivers. Barriers must suit the site risk rather than merely look robust.

A drawing is a communication tool, not proof of safety. The route must be walked and driven under representative conditions and changed after a near miss, altered phase, new vehicle or failed control.

Layout elementWhat to examineGood control
Pedestrian routeDoes it remain direct, accessible and clear during deliveries?Separate or protected route and crossing.
Vehicle routeCan the actual vehicle turn and stop with clearance?Competent swept-path and field check.
Loading areaCan the driver and loaders work without entering moving traffic?Controlled bay and vehicle restraint or other site-suitable controls.
Public boundaryCan a vehicle or load intrude into public space?Secure boundary and authority interface where applicable.
Emergency accessCan responders reach the site if a delivery is waiting?Unobstructed route and tested access plan.

Visual practice · Design separation that survives the shift

Actual SHAREsimulate construction model context: A proposed hoarding opening defeats site security
Actual SHAREsimulate model capture · A proposed hoarding opening defeats site security. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
What should a practical traffic layout model include?

A useful layout drawing shows both normal and changed routes, the people exposed and the clearance needed by the actual vehicle; it is checked on site. Show separate pedestrian and vehicle entry, direct walkways, controlled crossings, loading and turning space, parking, visibility, lighting, gradients, overhead services and emergency access. Recheck the plan when scaffolds, hoarding, road plates, excavations or welfare routes change; temporary works can create new vehicle-pedestrian interfaces. Check the path people actually choose, including disabled access and visiting drivers.

How can the ISO 45001 hierarchy of controls prevent workplace vehicle and pedestrian collisions?

For this example, remove or redesign the exposure first; use lower-order controls only for the risk that remains. The example is a planning aid, not approval of a live task. For Northern Ireland work, use this five-level framework to plan controls, then verify the applicable NI duties and HSENI guidance; HSE sources cited here state GB guidance. Worked scenario: HGV deliveries reverse towards a warehouse door across a pedestrian access route.

How harm develops in the linked model

Unauthorised people can reach excavations, climb structures or start plant; wind can also destabilise poorly designed hoarding.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How can the ISO 45001 hierarchy of controls prevent workplace vehicle and pedestrian collisions?

For this example, remove or redesign the exposure first; use lower-order controls only for the risk that remains. The example is a planning aid, not approval of a live task.

For Northern Ireland work, use this five-level framework to plan controls, then verify the applicable NI duties and HSENI guidance; HSE sources cited here state GB guidance.

Worked scenario: HGV deliveries reverse towards a warehouse door across a pedestrian access route. The HSE five-level hierarchy order elimination, substitution, engineering, administrative controls and PPE. HSE workplace traffic management supplies the topic context. ERICPD maps elimination to elimination, Reduce to substitution and source reduction, Isolate to engineered separation, Control to engineering and administrative arrangements, and PPE to residual personal protection. Discipline is the continuing check, maintenance, supervision and learning that keeps every chosen level effective; it is not blame or a replacement for design controls. For each row, the owner must show why any stronger feasible measure was not chosen, check the residual risk and hold work when the stated control fails. Feasibility test: An existing dock may not permit immediate forward-only circulation; a dated redesign decision is needed before relying on a controlled reverse.

How can the ERICPD hierarchy of controls prevent workplace vehicle and pedestrian collisions?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for Traffic Management
Activity and release context
Worked scenario: HGV deliveries reverse towards a warehouse door across a pedestrian access route. The HSE five-level hierarchy order elimination, substitution, engineering, administrative controls and PPE. HSE workplace traffic management supplies the topic context. ERICPD maps elimination to elimination, Reduce to substitution and source reduction, Isolate to engineered separation, Control to engineering and administrative arrangements, and PPE to residual personal protection. Discipline is the continuing check, maintenance, supervision and learning that keeps every chosen level effective; it is not blame or a replacement for design controls. For each row, the owner must show why any stronger feasible measure was not chosen, check the residual risk and hold work when the stated control fails. Feasibility test: An existing dock may not permit immediate forward-only circulation; a dated redesign decision is needed before relying on a controlled reverse.
Full example
Read the activity, checks and hand-back in context
HSE hierarchy levelERICPD counterpartSpecific action, owner, check and stop pointOfficial basis
EliminationEliminateMove the loading point or redesign circulation so vehicles enter and leave forwards without crossing a pedestrian route. The transport planner checks the swept path for the largest real vehicle and observes peak movements; a vehicle forced to reverse into people shows the design has failed.HSE control order; HSE workplace traffic management
SubstitutionReduce, including substitutionUse smaller vehicles, off-site consolidation or a timed remote drop where the load, road access and handling assessment permit it. The logistics manager checks new manual-handling, public-road and delivery risks; do not exchange one collision risk for an unsafe unloading task.HSE control order; HSE workplace traffic management
Engineering controlsIsolate or physical ControlInstall physical pedestrian barriers, protected crossings, suitable gates, lighting and a marked reversing bay with adequate clearance and ground capacity. A competent designer checks visibility and emergency access; the supervisor stops movement if a barrier is moved or a crossing cannot be controlled.HSE control order; HSE workplace traffic management
Administrative controlsAdministrative Control and DisciplineBook arrivals, brief drivers at entry, prohibit unscheduled reversing, use an agreed signaller only where needed and keep visitors out of manoeuvring zones. The yard lead observes the route and records near misses and changes. A signaller cannot compensate for a route that cannot safely accommodate the vehicle. Discipline sustains every control level: verify elimination and substitution decisions, inspect and maintain physical controls, check operating arrangements and residual PPE, investigate defects and worker feedback, and verify corrective action before closure.HSE control order; HSE workplace traffic management
PPEPPEProvide high-visibility clothing suited to light and weather for authorised people who must enter the traffic area, while checking it does not snag or obscure other protection. It improves conspicuity but cannot prevent impact. Missing segregation or uncontrolled reversing is a stop point even when PPE is worn.HSE control order; HSE workplace traffic management

How can the ISO 45001 hierarchy of controls prevent workplace vehicle and pedestrian collisions?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for Traffic Management
Activity and release context
Worked scenario: HGV deliveries reverse towards a warehouse door across a pedestrian access route. The HSE five-level hierarchy order elimination, substitution, engineering, administrative controls and PPE. HSE workplace traffic management supplies the topic context. ERICPD maps elimination to elimination, Reduce to substitution and source reduction, Isolate to engineered separation, Control to engineering and administrative arrangements, and PPE to residual personal protection. Discipline is the continuing check, maintenance, supervision and learning that keeps every chosen level effective; it is not blame or a replacement for design controls. For each row, the owner must show why any stronger feasible measure was not chosen, check the residual risk and hold work when the stated control fails. Feasibility test: An existing dock may not permit immediate forward-only circulation; a dated redesign decision is needed before relying on a controlled reverse.
Full example
Read the activity, checks and hand-back in context
HSE hierarchy levelERICPD counterpartSpecific action, owner, check and stop pointOfficial basis
EliminationEliminateMove the loading point or redesign circulation so vehicles enter and leave forwards without crossing a pedestrian route. The transport planner checks the swept path for the largest real vehicle and observes peak movements; a vehicle forced to reverse into people shows the design has failed.HSE control order; HSE workplace traffic management
SubstitutionReduce, including substitutionUse smaller vehicles, off-site consolidation or a timed remote drop where the load, road access and handling assessment permit it. The logistics manager checks new manual-handling, public-road and delivery risks; do not exchange one collision risk for an unsafe unloading task.HSE control order; HSE workplace traffic management
Engineering controlsIsolate or physical ControlInstall physical pedestrian barriers, protected crossings, suitable gates, lighting and a marked reversing bay with adequate clearance and ground capacity. A competent designer checks visibility and emergency access; the supervisor stops movement if a barrier is moved or a crossing cannot be controlled.HSE control order; HSE workplace traffic management
Administrative controlsAdministrative Control and DisciplineBook arrivals, brief drivers at entry, prohibit unscheduled reversing, use an agreed signaller only where needed and keep visitors out of manoeuvring zones. The yard lead observes the route and records near misses and changes. A signaller cannot compensate for a route that cannot safely accommodate the vehicle. Discipline sustains every control level: verify elimination and substitution decisions, inspect and maintain physical controls, check operating arrangements and residual PPE, investigate defects and worker feedback, and verify corrective action before closure.HSE control order; HSE workplace traffic management
PPEPPEProvide high-visibility clothing suited to light and weather for authorised people who must enter the traffic area, while checking it does not snag or obscure other protection. It improves conspicuity but cannot prevent impact. Missing segregation or uncontrolled reversing is a stop point even when PPE is worn.HSE control order; HSE workplace traffic management

ERICPD Discipline in this example: The yard lead reviews swept paths and near misses, maintains barriers and crossings, and withdraws movement authority after a pedestrian enters the reversing zone. After a change, the supervisor verifies the strongest installed control at the workface and records any remaining exposure. If elimination or substitution was rejected, record the task-specific reason and revisit it when the process, equipment or site changes.

Apply the learning

Stored materials force pedestrians from a protected walkway into the haul route.

Decision and explanation

Stop the conflict and restore a usable separated route before movements resume.

A route must remain physically usable; a drawn line or signed plan does not protect people when the route is blocked.

Lesson 5

Reversing, visibility and banksman limits

Avoid reversing where possible. A signaller is a residual control with clear limits, not a substitute for route design and exclusion.

Why is a banksman not a substitute for good layout?

Remove or minimise reversing and exclude pedestrians first. A trained signaller is not required for every reverse; where suitable and used, the driver stops immediately on losing sight of the signaller, even with radio contact.

Only where reversing cannot be removed and a signaller is suitable for the vehicle and industry, use a trained, authorised person with agreed signals in a safe position outside the vehicle path and continuously visible to the driver. The driver must stop immediately if sight of the signaller is lost, even when radio contact remains; radio is an additional aid, not a substitute for visibility. Exclude other people and control conflicting movements. Some vehicle or industry situations prohibit or make signallers unsuitable.

The employer should first ask whether a one-way or drive-through arrangement could remove the manoeuvre. A roadworks traffic operative is not automatically a workplace reversing signaller, or vice versa; competence must match the task.

Weak useBetter approachEvidence
Used instead of layoutRemove reversing or separate the route first.Revised plan and field check.
Stands in blind spotUse an agreed safe position outside the vehicle path, continuously visible to the driver.Task observation.
Driver loses sight of signaller but radio still worksStop immediately; radio cannot replace sight. Reset the safe visible position and signals before movement.Driver and signaller briefing, observation and stop rule.
Conflicting movementsControl one movement and exclude other users.Gate or bay coordination record.

Visual practice · Reversing, visibility and banksman limits

Workers on a protected walkway separated by continuous guardrails from a site dumper on a UK construction site
SHAREhub photographic illustration · Workers on a protected walkway separated by continuous guardrails from a site dumper on a UK construction site. Use the written case for the exercise; this image does not prove a defect or safe system.
Why is a banksman not a substitute for good layout?

Remove or minimise reversing and exclude pedestrians first. A trained signaller is not required for every reverse; where suitable and used, the driver stops immediately on losing sight of the signaller, even with radio contact. Only where reversing cannot be removed and a signaller is suitable for the vehicle and industry, use a trained, authorised person with agreed signals in a safe position outside the vehicle path and continuously visible to the driver.

When should traffic movements stop immediately?

Stop the affected movement when separation, visibility, route condition, vehicle control, emergency access or an applicable road approval is missing or uncertain. A driver who loses sight of a signaller stops immediately, even if the radio still works. Drivers and workers should have a clear stop signal and safe waiting place. Do not ask a marshal to rescue a defective layout.

How harm develops in the linked model

The public may be struck, trapped or forced into the road; visitors may not understand the site traffic system.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

When should traffic movements stop immediately?

Stop the affected movement when separation, visibility, route condition, vehicle control, emergency access or an applicable road approval is missing or uncertain. A driver who loses sight of a signaller stops immediately, even if the radio still works.

Drivers and workers should have a clear stop signal and safe waiting place. Do not ask a marshal to rescue a defective layout. Make the area safe, report the defect, reassess and restart only when an authorised person has verified the changed controls.

For a collision, summon emergency help, prevent further movement and protect responders without moving an injured person unnecessarily. Follow local emergency and reporting arrangements; investigate before returning the route to service.

Stop triggerWhy it mattersAction
Pedestrian barrier or crossing failedPeople can enter the vehicle path.Hold movement, restore separation and verify.
Unknown or obstructed routeDriver may improvise through an exposed area.Hold at a safe point; clear or redesign and brief.
Failed safety-critical vehicle aidVisibility or warning may be inadequate.Quarantine or restrict the vehicle pending competent assessment.
Poor light, weather or groundThe assessed manoeuvre no longer matches conditions.Suspend affected movement and reassess.
Emergency route blockedResponse and evacuation could fail.Stop the obstruction and restore access.
Public-road control unapproved or damagedRoad users may enter a work area.Do not install or continue an unsafe scheme; escalate to scheme owner and authority.
Driver loses sight of signaller, even with radio contactThe signaller is no longer continuously visible in a safe guiding position.Stop immediately; do not reverse again until the visible arrangement is safely reset.

Apply the learning

A reversing driver loses sight of the agreed signaller.

Decision and explanation

Stop immediately and re-establish a safe communication and exclusion arrangement.

Avoid reversing where possible. A signaller is a residual control with clear limits, not a substitute for route design and exclusion.

Lesson 6

Select and authorise operators

Competence must match the equipment, attachment, task and conditions; a generic credential is only part of the evidence.

Plant questions: test the actual control

The answer depends on the live route, machine and jurisdiction. Training, a banksman and a warning alarm each have a defined supporting role. IS DRIVER TRAINING ENOUGH?: No. The manager must make safe site, suitable vehicle and competent driver controls work together.

CAN A BANKSMAN REPLACE BARRIERS?: A banksman supports a designed system; they do not replace feasible physical segregation. WHAT IF BRAKES OR STEERING FAIL?: Quarantine the vehicle and verify repair before use. A warning or experienced driver cannot resolve the defect. WHAT IF THE ROUTE CHANGES?: Stop affected movement.

Revise, brief and observe the new route before restarting. WHICH LAW APPLIES IN NI?: Northern Ireland has its own 1999 PUWER and workplace-route instrument; GB regulations are not the NI legal route.

Visual practice · Select and authorise operators

Actual SHAREsimulate construction model context: A safety-critical operator may be impaired
Actual SHAREsimulate model capture · A safety-critical operator may be impaired. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Plant questions: test the actual control

The answer depends on the live route, machine and jurisdiction. Training, a banksman and a warning alarm each have a defined supporting role. IS DRIVER TRAINING ENOUGH?: No. The manager must make safe site, suitable vehicle and competent driver controls work together.

What should each role demonstrate?

Competence is shown by an observed task decision, stop trigger and corrected defect, not course attendance alone.

How harm develops in the linked model

Fatigue, illness, medication, alcohol or drugs can affect safe operation; appearance alone does not identify the cause.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What should each role demonstrate?

Competence is shown by an observed task decision, stop trigger and corrected defect, not course attendance alone.

Role competence
Role Skill Demonstration
Operator Check vehicle, route, visibility, restraint and ground before movement. A competent plant trainer observes pre-use and defect quarantine, records authorisation and reassesses after plant or route change. Sources: HSE construction site dumpers; HSE mobile work equipment.
Supervisor Separate pedestrians, deliveries and plant through each construction phase. A traffic-plan lead witnesses a site walk, records crossing/visitor controls and repeats after a new trade or layout change. Sources: HSE construction site traffic management; HSE safe use of vehicles on construction sites HSG144.
Site manager Plan phases, review ground and lifting interfaces, and approve traffic changes. A competent construction manager signs the live traffic plan and checks it after incident, near miss or phase change. Sources: HSE construction site traffic management; Construction (Design and Management) Regulations 2015; Construction (Design and Management) Regulations (NI) 2016.
Specialist Assess rollover, stability, restraints and lifting scope within technical competence. A senior engineer peer-reviews the task record, retains evidence and repeats after attachment or ground change. Sources: HSE construction site dumpers; HSE safe use of vehicles on construction sites HSG144; HSE rider-operated lift trucks L117.

Apply the learning

A trained operator is assigned a machine and attachment they have never used.

Decision and explanation

Confirm task suitability, familiarisation, competence and authorisation before use.

Competence must match the equipment, attachment, task and conditions; a generic credential is only part of the evidence.

Lesson 7

Excavators: slew, buckets and quick hitches

Attachment security and exclusion must be positively verified. People must not be used to test a potentially unsafe attachment.

Dumper route change: hold, revise and verify

Illustrative changing construction site. A pedestrian shortcut enters a reversing area under poor temporary lighting; controls must be checked for the current phase. Start: A site dumper is delivering fill beside a pedestrian route that has changed. Question 1: Has the workface, delivery pattern or pedestrian route changed?

Decision owner: Site supervisor. YES: Stop affected dumper movement and review the current phase layout. Owner: Site supervisor. CONTINUE → QUESTION 2.

NO: Check the current route rather than assume the original plan still works. UNKNOWN: Hold affected movement until current site changes are established. HOLD → REPEAT QUESTION 1 AFTER CORRECTION. Question 2: Are people separated from the dumper path?

YES: Protect and retain the pedestrian route for the next checks. CONTINUE → QUESTION 3. NO: Stop movement; direct people to a protected route and restore segregation. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.

UNKNOWN: Hold movement while the manager checks crossings, visitors and subcontractor access. Question 3: Are ground and turning conditions suitable for the dumper? Decision owner: Site supervisor with competent plant support. YES: Check visibility and the current delivery interface.

Owner: Site supervisor with competent plant support. CONTINUE → QUESTION 4. NO: Keep movement held; reassess the route and equipment for the ground and turn. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.

UNKNOWN: Keep movement held; obtain competent evidence about ground and manoeuvring. Question 4: Is visibility adequate for the current route and task? YES: Include lighting and view in the revised traffic arrangement. CONTINUE → QUESTION 5.

NO: Hold movement; correct lighting or visibility before relying on the route. HOLD → REPEAT QUESTION 4 AFTER CORRECTION. UNKNOWN: Hold movement and verify view and lighting under the conditions of use. Question 5: Is the revised traffic plan briefed to affected people?

Decision owner: Site manager. YES: Check the arrangement at the next delivery. Owner: Site manager. CONTINUE → QUESTION 6.

NO: Hold affected movement until operators, workers and subcontractors understand the route. HOLD → REPEAT QUESTION 5 AFTER CORRECTION. UNKNOWN: Hold movement and resolve the briefing/coordination gap with the site manager. Question 6: Does observation confirm the revised route works?

Decision owner: Site manager and supervisor. YES: Record the checked arrangement and continue monitoring the current phase. Owner: Site manager and supervisor. OUTCOME → RECORD AND HAND OVER.

NO: Stop affected movement again; revise the failed route or interface. HOLD → REPEAT QUESTION 6 AFTER CORRECTION. UNKNOWN: Keep movement held until representative observation supports the arrangement. Outcome: The site manager records the current plan, briefing and observed arrangement; later changes reopen the route review.

Stop and escalation boundary: A banksman, high-visibility clothing or warning alarm supports a designed system and cannot establish safe segregation by itself.

Visual practice · Excavators: slew, buckets and quick hitches

Mini excavator and hire equipment awaiting checks in a UK depot
SHAREhub photographic illustration · Mini excavator and hire equipment awaiting checks in a UK depot. Use the written case for the exercise; this image does not prove a defect or safe system.
Dumper route change: hold, revise and verify

Illustrative changing construction site. A pedestrian shortcut enters a reversing area under poor temporary lighting; controls must be checked for the current phase. Start: A site dumper is delivering fill beside a pedestrian route that has changed. Question 1: Has the workface, delivery pattern or pedestrian route changed?

How harm develops in the linked model

The bucket or counterweight can strike or crush people; a detached attachment can fall suddenly.

What a workface check adds

Check the actual hitch configuration and pre-use evidence, operator visibility and complete slew zone before movements resume.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Apply the learning

A worker approaches an excavator bucket while an attachment change is incomplete.

Decision and explanation

Stop movement, keep people out of the operating envelope and verify the attachment through the specified procedure.

Attachment security and exclusion must be positively verified. People must not be used to test a potentially unsafe attachment.

Lesson 8

Dumpers and overturn risk

Ground and route design control stability; skill and speed cannot correct an unsuitable edge or bearing condition.

When must mobile plant or lift-truck work stop?

Stop if a person is in the operating zone, the route or ground is unsafe, visibility fails, a load is unstable or a critical vehicle defect is unresolved.

Isolate the equipment and prevent unauthorised restart. A reversing alarm, high-visibility clothing or banksman does not make a shared route safe by itself. The responsible supervisor checks the corrected route and machine before hand-back. Sources: HSE introduction to workplace transport safety, HSE mobile work equipment, HSENI workplace transport.

Visual practice · Dumpers and overturn risk

Actual SHAREsimulate construction model context: A dumper tip is proposed on unverified ground
Actual SHAREsimulate model capture · A dumper tip is proposed on unverified ground. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
When must mobile plant or lift-truck work stop?

Stop if a person is in the operating zone, the route or ground is unsafe, visibility fails, a load is unstable or a critical vehicle defect is unresolved. Isolate the equipment and prevent unauthorised restart. A reversing alarm, high-visibility clothing or banksman does not make a shared route safe by itself. The responsible supervisor checks the corrected route and machine before hand-back.

How can the hierarchy of controls prevent mobile-plant collisions and pedestrian injuries?

Design out unnecessary vehicle/pedestrian conflict and reversing before relying on signals or visibility clothing. The vehicle, route and driver must all be suitable for the changing site. Illustrative decision: a dumper supplies material through a changing construction site near workers and an excavation. Site management and competent plant staff assess the actual route, ground, edge, load and interfaces.

How harm develops in the linked model

Overturn can eject or crush the operator; poor visibility, overload and edge collapse can also injure nearby workers.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How can the hierarchy of controls prevent mobile-plant collisions and pedestrian injuries?

Design out unnecessary vehicle/pedestrian conflict and reversing before relying on signals or visibility clothing. The vehicle, route and driver must all be suitable for the changing site.

Illustrative decision: a dumper supplies material through a changing construction site near workers and an excavation. Site management and competent plant staff assess the actual route, ground, edge, load and interfaces.

ERICPD means Eliminate, Reduce (including substitution), Isolate, Control, PPE and Discipline. The five-level hierarchy groups measures as elimination, substitution, engineering controls, administrative controls and PPE. They overlap: isolation is usually an engineering measure; control can include engineered and administrative measures. Discipline means maintaining and checking the controls, supervising the method and learning from defects, rather than blaming someone or accepting weaker protection.

How can the ERICPD hierarchy of controls prevent mobile-plant collisions and pedestrian injuries?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for Mobile plant and vehicles
Activity and release context
Illustrative decision: a dumper supplies material through a changing construction site near workers and an excavation. Site management and competent plant staff assess the actual route, ground, edge, load and interfaces.
Full example
Read the activity, checks and hand-back in context
Controls and evidence for the illustrative task
ERICPD and five-level positionIntervention and ownerVerification, failure and stop point
Eliminate / eliminationReplan material delivery so the dumper need not enter the pedestrian work zone; consider a suitable layout removing reversing.Verify the full material route and transferred risks. A one-way arrow is not elimination if drivers must still reverse in the work zone.
Reduce / substitution when replacing a hazard; otherwise engineering or administrative risk reductionCompare a suitable delivery method or equipment with lower risk for the actual task, load and ground.Check capability, stability, access and new risks. Smaller plant is not automatically suitable or safer.
Isolate / engineeringProvide suitable physical segregation and assessed ground/edge and vehicle protections for the actual operation.Inspect the real route after site changes. Inadequate ground, edge protection, visibility or segregation holds the affected movement.
Control / administrativeCoordinate deliveries, exclusion, competent authorised operation, inspection and communication; use signallers only through the assessed method.Verify safe conditions and signals. Stop if people enter the exclusion, a signaller is lost from view or conditions change; no generic safe edge distance is given.
PPE / PPEProvide assessed visibility and residual protection for the task.Check suitability; clothing cannot prevent collision or overturn and does not replace segregation.
Discipline / sustained engineering and administrative controlsSite management reviews route changes, defects and near misses with drivers and workers.Retain restrictions and verified corrective actions. A changing excavation, route or load requires renewed assessment.

How can the ISO 45001 hierarchy of controls prevent mobile-plant collisions and pedestrian injuries?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for Mobile plant and vehicles
Activity and release context
Illustrative decision: a dumper supplies material through a changing construction site near workers and an excavation. Site management and competent plant staff assess the actual route, ground, edge, load and interfaces.
Full example
Read the activity, checks and hand-back in context
Controls and evidence for the illustrative task
ERICPD and five-level positionIntervention and ownerVerification, failure and stop point
Eliminate / eliminationReplan material delivery so the dumper need not enter the pedestrian work zone; consider a suitable layout removing reversing.Verify the full material route and transferred risks. A one-way arrow is not elimination if drivers must still reverse in the work zone.
Reduce / substitution when replacing a hazard; otherwise engineering or administrative risk reductionCompare a suitable delivery method or equipment with lower risk for the actual task, load and ground.Check capability, stability, access and new risks. Smaller plant is not automatically suitable or safer.
Isolate / engineeringProvide suitable physical segregation and assessed ground/edge and vehicle protections for the actual operation.Inspect the real route after site changes. Inadequate ground, edge protection, visibility or segregation holds the affected movement.
Control / administrativeCoordinate deliveries, exclusion, competent authorised operation, inspection and communication; use signallers only through the assessed method.Verify safe conditions and signals. Stop if people enter the exclusion, a signaller is lost from view or conditions change; no generic safe edge distance is given.
PPE / PPEProvide assessed visibility and residual protection for the task.Check suitability; clothing cannot prevent collision or overturn and does not replace segregation.
Discipline / sustained engineering and administrative controlsSite management reviews route changes, defects and near misses with drivers and workers.Retain restrictions and verified corrective actions. A changing excavation, route or load requires renewed assessment.

The comparison is an original illustrative application of the general HSE hierarchy, not a machine-specific method, permit or design approval. The employer must choose measures for the actual work and jurisdiction. Apply the separate Northern Ireland legal route where relevant; the local assessment and competent technical decision govern release.

Sources: HSE hierarchy of controls; HSE construction site traffic management; HSE construction site dumpers; HSE mobile work equipment; HSENI workplace transport.

Apply the learning

A loaded dumper route now crosses soft ground close to a trench.

Decision and explanation

Hold the route and reassess ground, gradient, edge protection and machine limits.

Ground and route design control stability; skill and speed cannot correct an unsuitable edge or bearing condition.

Lesson 9

Telehandlers: load, reach and ground

Capacity changes with reach and configuration. Site conditions and the actual load must fit the planned operating limits.

Stopped plant still contains hazardous energy

Stationary is not the same as immobilised, isolated and supported. The task owner verifies the actual loading, repair or coupling arrangement. TIPPING: GROUND AND LOAD: Uneven load, soft ground or edge collapse can overturn a dumper. Stop where bearing or edge conditions are uncertain; use the assessed tipping arrangement.

RAISED BODY: GRAVITY: A body or attachment can fall after hydraulic failure. Competent maintenance isolates energy and uses manufacturer-approved mechanical support, not hydraulics alone. LOADING OR COUPLING: MOVEMENT: Rollaway or an unstable load can crush people. Check brakes, firm ground and exclusion before the task.

HAND-BACK: VERIFY THE BARRIER: The supervisor checks cab/platform access, attachment lock and maintenance hand-back. Failed support, brake, coupling or exclusion keeps plant out of service.

Visual practice · Telehandlers: load, reach and ground

Mini excavator and hire equipment awaiting checks in a UK depot
SHAREhub photographic illustration · Mini excavator and hire equipment awaiting checks in a UK depot. Use the written case for the exercise; this image does not prove a defect or safe system.
Stopped plant still contains hazardous energy

Stationary is not the same as immobilised, isolated and supported. The task owner verifies the actual loading, repair or coupling arrangement. TIPPING: GROUND AND LOAD: Uneven load, soft ground or edge collapse can overturn a dumper. Stop where bearing or edge conditions are uncertain; use the assessed tipping arrangement.

How harm develops in the linked model

Capacity changes with reach and configuration; an unstable or insecure load can overturn the machine or strike people.

What a workface check adds

Check load weight and security, reach, attachment compatibility, actual ground and people controls before the handling operation proceeds.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Apply the learning

A load is within the machine’s headline capacity but must be placed at extended reach.

Decision and explanation

Check the actual configuration, attachment, load chart, ground and planned placement before lifting.

Capacity changes with reach and configuration. Site conditions and the actual load must fit the planned operating limits.

Lesson 10

Deliveries, unloading and storage

Delivery planning includes arrival, waiting, load security, unloading and storage. Schedule pressure does not establish a safe work area.

How do traffic controls differ by vehicle and activity?

Select controls for the actual vehicle, load, driver, surface and people; the same plan cannot be copied between a warehouse, yard and roadworks site.

Forklift aisles, HGV deliveries, telehandlers, tippers, skip exchanges, moving MEWPs, waste collection and event parking have different blind spots, pedestrian peaks, turning and load risks. The operator checks the equipment and route; a supervisor coordinates the people and other tasks. Road-going vehicles on public roads also face a separate road-traffic regime.

Use manufacturer instructions and task-specific assessment for vehicle limits, restraint, lifting and tipping. This page provides no universal speed, turning radius, clearance or stopping distance.

Vehicle or activityTypical failure modeMain control
HGV deliveryReverses across a walkway or waits on a public road.Booked arrival, safe waiting point, separated route and unloading bay.
Forklift in warehousePedestrian enters aisle or blind corner.Physical separation, controlled crossings, suitable vehicle and trained operator.
Telehandler on construction siteLoad obscures view or ground cannot support movement.Suitable route, exclusion zone, load control and competent operator.
Tipper or skip exchangeOverturn, overhead strike or people near moving container.Ground and overhead checks, controlled zone and task-specific method.
Public-road worksRoad user meets unprotected work area or inaccessible footway.Competent temporary traffic scheme, authority approval and live inspection.
MEWP repositioningStrikes a person or structure during movement.Check the actual travel path, stability and exclusion zone; use a signaller only if suitable.
Waste collectionCollection vehicle reverses near workers or the public.Design collection point and timing to minimise reversing; separate people and brief the driver.
Event parkingPeak pedestrian flows mix with arriving or departing vehicles.Plan separated flows, suitable marshal positions, lighting and clear emergency access.

Visual practice · Deliveries, unloading and storage

Actual SHAREsimulate construction model context: An unplanned delivery adds rolling and handling risks
Actual SHAREsimulate model capture · An unplanned delivery adds rolling and handling risks. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
How do traffic controls differ by vehicle and activity?

Select controls for the actual vehicle, load, driver, surface and people; the same plan cannot be copied between a warehouse, yard and roadworks site. Forklift aisles, HGV deliveries, telehandlers, tippers, skip exchanges, moving MEWPs, waste collection and event parking have different blind spots, pedestrian peaks, turning and load risks. The operator checks the equipment and route; a supervisor coordinates the people and other tasks. Road-going vehicles on public roads also face a separate road-traffic regime.

What should teams check before, during and after each movement?

Check the route, vehicle, people and conditions; hold on a failed interface and verify the hand-back before movement resumes.

How harm develops in the linked model

Collapsing or rolling materials can crush people. Repeated heavy and awkward handling can cause musculoskeletal injury.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What should teams check before, during and after each movement?

Check the route, vehicle, people and conditions; hold on a failed interface and verify the hand-back before movement resumes.

Task and peopleBefore movementDuring movement and holdAfter and evidence
Routine HGV delivery at a yard; driver, loaders and walkers.Book slot, check gate, route, loading bay, pedestrian separation, vehicle and driver briefing.Keep people out of manoeuvre zone; hold for a blocked bay, unclear route or failed restraint.Restore route, release vehicle safely, record defects and hand-back.
Forklift movement through warehouse; operator and nearby staff.Check truck, load, aisle, crossings and barriers; confirm operator competence.Use protected route; hold if pedestrian enters aisle or visibility is lost.Park safely, report damage and reinstate barriers.
Non-routine scaffold delivery on construction phase change; contractors and visitors.Coordinate revised access, ground and public boundary; brief driver and work team.Hold when new storage blocks walkway or vehicle cannot turn as planned.Inspect separation and update phase plan and briefing.
Failed reversing alarm or damaged barrier; driver and supervisor.Know safe stop location and defect reporting route.Stop affected movement; do not use a marshal to compensate for uncertain control.Competent repair or alternative assessment, authorised restart and record.
Collision or blocked emergency access; everyone on site.Know emergency route and who controls gates.Stop traffic, summon help and protect responders; do not improvise a new route.Preserve facts, investigate, restore access and verify hand-back.

Apply the learning

A delivery arrives early and the planned unloading area is occupied.

Decision and explanation

Hold the vehicle in a safe agreed place until unloading and pedestrian controls are ready.

Delivery planning includes arrival, waiting, load security, unloading and storage. Schedule pressure does not establish a safe work area.

Lesson 11

Lifting interfaces and exclusion

Loads, machines and people need a coordinated arrangement with clear exclusion and communication, not informal timing.

How should a changing construction site manage a dumper?

Plan pedestrian and dumper routes for each construction phase, then stop and revise them when the workface or deliveries change.

At fictional BuildOut Ltd, a site dumper is delivering fill beside a changing pedestrian path. A new trade opens a shortcut across the reversing zone while temporary lighting is poor. The supervisor stops dumper movement, directs people to a protected route, checks turning and ground conditions, and updates the traffic plan before restarting. A banksman or warning alarm supports a designed route; neither replaces physical separation where feasible. The manager briefs subcontractors and verifies the new route during the next delivery. Sources: HSE construction site traffic management, HSE introduction to workplace transport safety, HSENI workplace transport.

Visual practice · Lifting interfaces and exclusion

Mini excavator and hire equipment awaiting checks in a UK depot
SHAREhub photographic illustration · Mini excavator and hire equipment awaiting checks in a UK depot. Use the written case for the exercise; this image does not prove a defect or safe system.
How should a changing construction site manage a dumper?

Plan pedestrian and dumper routes for each construction phase, then stop and revise them when the workface or deliveries change. At fictional BuildOut Ltd, a site dumper is delivering fill beside a changing pedestrian path. A new trade opens a shortcut across the reversing zone while temporary lighting is poor. The supervisor stops dumper movement, directs people to a protected route, checks turning and ground conditions, and updates the traffic plan before restarting.

How can the hierarchy of controls prevent mobile-plant collisions and pedestrian injuries?

Design out unnecessary vehicle/pedestrian conflict and reversing before relying on signals or visibility clothing. The vehicle, route and driver must all be suitable for the changing site. Illustrative decision: a dumper supplies material through a changing construction site near workers and an excavation. Site management and competent plant staff assess the actual route, ground, edge, load and interfaces.

How harm develops in the linked model

Capacity changes with reach and configuration; an unstable or insecure load can overturn the machine or strike people.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How can the hierarchy of controls prevent mobile-plant collisions and pedestrian injuries?

Design out unnecessary vehicle/pedestrian conflict and reversing before relying on signals or visibility clothing. The vehicle, route and driver must all be suitable for the changing site.

Illustrative decision: a dumper supplies material through a changing construction site near workers and an excavation. Site management and competent plant staff assess the actual route, ground, edge, load and interfaces.

ERICPD means Eliminate, Reduce (including substitution), Isolate, Control, PPE and Discipline. The five-level hierarchy groups measures as elimination, substitution, engineering controls, administrative controls and PPE. They overlap: isolation is usually an engineering measure; control can include engineered and administrative measures. Discipline means maintaining and checking the controls, supervising the method and learning from defects, rather than blaming someone or accepting weaker protection.

How can the ERICPD hierarchy of controls prevent mobile-plant collisions and pedestrian injuries?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for Mobile plant and vehicles
Activity and release context
Illustrative decision: a dumper supplies material through a changing construction site near workers and an excavation. Site management and competent plant staff assess the actual route, ground, edge, load and interfaces.
Full example
Read the activity, checks and hand-back in context
Controls and evidence for the illustrative task
ERICPD and five-level positionIntervention and ownerVerification, failure and stop point
Eliminate / eliminationReplan material delivery so the dumper need not enter the pedestrian work zone; consider a suitable layout removing reversing.Verify the full material route and transferred risks. A one-way arrow is not elimination if drivers must still reverse in the work zone.
Reduce / substitution when replacing a hazard; otherwise engineering or administrative risk reductionCompare a suitable delivery method or equipment with lower risk for the actual task, load and ground.Check capability, stability, access and new risks. Smaller plant is not automatically suitable or safer.
Isolate / engineeringProvide suitable physical segregation and assessed ground/edge and vehicle protections for the actual operation.Inspect the real route after site changes. Inadequate ground, edge protection, visibility or segregation holds the affected movement.
Control / administrativeCoordinate deliveries, exclusion, competent authorised operation, inspection and communication; use signallers only through the assessed method.Verify safe conditions and signals. Stop if people enter the exclusion, a signaller is lost from view or conditions change; no generic safe edge distance is given.
PPE / PPEProvide assessed visibility and residual protection for the task.Check suitability; clothing cannot prevent collision or overturn and does not replace segregation.
Discipline / sustained engineering and administrative controlsSite management reviews route changes, defects and near misses with drivers and workers.Retain restrictions and verified corrective actions. A changing excavation, route or load requires renewed assessment.

How can the ISO 45001 hierarchy of controls prevent mobile-plant collisions and pedestrian injuries?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for Mobile plant and vehicles
Activity and release context
Illustrative decision: a dumper supplies material through a changing construction site near workers and an excavation. Site management and competent plant staff assess the actual route, ground, edge, load and interfaces.
Full example
Read the activity, checks and hand-back in context
Controls and evidence for the illustrative task
ERICPD and five-level positionIntervention and ownerVerification, failure and stop point
Eliminate / eliminationReplan material delivery so the dumper need not enter the pedestrian work zone; consider a suitable layout removing reversing.Verify the full material route and transferred risks. A one-way arrow is not elimination if drivers must still reverse in the work zone.
Reduce / substitution when replacing a hazard; otherwise engineering or administrative risk reductionCompare a suitable delivery method or equipment with lower risk for the actual task, load and ground.Check capability, stability, access and new risks. Smaller plant is not automatically suitable or safer.
Isolate / engineeringProvide suitable physical segregation and assessed ground/edge and vehicle protections for the actual operation.Inspect the real route after site changes. Inadequate ground, edge protection, visibility or segregation holds the affected movement.
Control / administrativeCoordinate deliveries, exclusion, competent authorised operation, inspection and communication; use signallers only through the assessed method.Verify safe conditions and signals. Stop if people enter the exclusion, a signaller is lost from view or conditions change; no generic safe edge distance is given.
PPE / PPEProvide assessed visibility and residual protection for the task.Check suitability; clothing cannot prevent collision or overturn and does not replace segregation.
Discipline / sustained engineering and administrative controlsSite management reviews route changes, defects and near misses with drivers and workers.Retain restrictions and verified corrective actions. A changing excavation, route or load requires renewed assessment.

The comparison is an original illustrative application of the general HSE hierarchy, not a machine-specific method, permit or design approval. The employer must choose measures for the actual work and jurisdiction. Apply the separate Northern Ireland legal route where relevant; the local assessment and competent technical decision govern release.

Sources: HSE hierarchy of controls; HSE construction site traffic management; HSE construction site dumpers; HSE mobile work equipment; HSENI workplace transport.

Apply the learning

A pedestrian route passes beneath a proposed materials placement.

Decision and explanation

Prevent the conflict using an agreed lift and movement plan before handling the load.

Loads, machines and people need a coordinated arrangement with clear exclusion and communication, not informal timing.

Lesson 12

Stationary plant and stored energy

Unexpected restart, gravity, hydraulic pressure and other stored energy can remain after a normal stop. Maintenance access needs a safe isolation system.

What hazards remain while plant is stopped or loading?

A stationary vehicle can still roll, tip, shed a load or crush someone under a raised body or attachment. Immobilise, support and isolate before intervention.

Stopped and loading plant decisions
Task Failure route Control and stop trigger
Dumper tipping Uneven load, soft ground or edge collapse. Use firm level ground, distributed load and safe edge stop; stop if bearing/edge is uncertain.Sources: HSE construction site dumpers; HSE safe use of vehicles on construction sites HSG144
Raised body or hydraulic repair Hydraulic failure drops body or attachment. Isolate energy and fit manufacturer-approved mechanical support; never rely on hydraulics alone.Sources: HSE safe use of vehicles on construction sites HSG144; HSE mobile work equipment
Loading or trailer coupling Rollaway, unstable load or person in loading zone. Apply brakes, check firm ground and secure exclusion before coupling/loading.Sources: HSE coupling and uncoupling; HSE workplace transport loading areas

The supervisor checks access to the cab and any loading platform, the attachment lock and maintenance hand-back before releasing the machine. If a support, brake, coupling or exclusion control fails, keep the plant out of service. Sources: HSE safe use of vehicles on construction sites HSG144, HSE coupling and uncoupling, HSE workplace transport loading areas.

Visual practice · Stationary plant and stored energy

Actual SHAREsimulate construction model context: A mixer jam is reached through an open guard
Actual SHAREsimulate model capture · A mixer jam is reached through an open guard. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
What hazards remain while plant is stopped or loading?

What hazards remain while plant is stopped or loading? A stationary vehicle can still roll, tip, shed a load or crush someone under a raised body or attachment. Immobilise, support and isolate before intervention. Stopped plant still contains hazardous energy Learning point: Stationary is not the same as immobilised, isolated and supported.

How harm develops in the linked model

Unexpected movement can entangle or crush a hand. Emergency stop is not a maintenance isolation system.

What a workface check adds

Verify all relevant energy is isolated and cannot cause movement, guards are restored and a controlled functional check confirms safe return.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Distinguish checking a restraint from using it

For the assessed dumper, use the provided seat restraint; ROPS alone does not keep the operator within its protective space. Keep loads within manufacturer limits and clear of the sightline. Follow the specified loading position: an operator on an exposed dumper leaves during loading and waits safely outside plant movement. Do not travel with an elevated high-lift skip. Match the method to the actual dumper/cab and competent instructions. HSE CIS52: dumpers.

Apply the learning

A conveyor jams and a worker reaches toward it after pressing the stop button.

Decision and explanation

Use the required isolation, stored-energy controls and verification before access.

Unexpected restart, gravity, hydraulic pressure and other stored energy can remain after a normal stop. Maintenance access needs a safe isolation system.

Lesson 13

Overhead lines and changing envelopes

Plant can bridge a safe-looking gap as its envelope changes. Do not estimate safe clearance from appearance.

When must mobile plant or lift-truck work stop?

Stop if a person is in the operating zone, the route or ground is unsafe, visibility fails, a load is unstable or a critical vehicle defect is unresolved.

Isolate the equipment and prevent unauthorised restart. A reversing alarm, high-visibility clothing or banksman does not make a shared route safe by itself. The responsible supervisor checks the corrected route and machine before hand-back. Sources: HSE introduction to workplace transport safety, HSE mobile work equipment, HSENI workplace transport.

Visual practice · Overhead lines and changing envelopes

Mini excavator and hire equipment awaiting checks in a UK depot
SHAREhub photographic illustration · Mini excavator and hire equipment awaiting checks in a UK depot. Use the written case for the exercise; this image does not prove a defect or safe system.
When must mobile plant or lift-truck work stop?

Stop if a person is in the operating zone, the route or ground is unsafe, visibility fails, a load is unstable or a critical vehicle defect is unresolved. Isolate the equipment and prevent unauthorised restart. A reversing alarm, high-visibility clothing or banksman does not make a shared route safe by itself. The responsible supervisor checks the corrected route and machine before hand-back.

Which national legal routes apply?

Which national legal routes apply? Choose the instrument for the actual site and task. Great Britain (GB) and Northern Ireland (NI) have separate equipment and workplace-route laws; lifting and construction add scope-specific duties. Use the legal route with the relevant national regulator’s current guidance, then seek competent site-specific review of amendments, premises and task scope.

How harm develops in the linked model

Fatal shock or flashover can occur without direct contact; height, reach, movement and changing ground all affect the approach.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Which national legal routes apply?

Choose the instrument for the actual site and task. Great Britain (GB) and Northern Ireland (NI) have separate equipment and workplace-route laws; lifting and construction add scope-specific duties.

Use the legal route with the relevant national regulator’s current guidance, then seek competent site-specific review of amendments, premises and task scope. Do not treat a GB instrument as NI law. Sources: Health and Safety at Work etc. Act 1974, Health and Safety at Work (NI) Order 1978.

National duty routes
Issue Great Britain or England/Wales and Scotland Northern Ireland
General safety and assessment GB 1974 Act and Management Regulations 1999 NI 1978 Order and Management Regulations 2000Sources: Health and Safety at Work etc. Act 1974; Health and Safety at Work (NI) Order 1978; Management of Health and Safety at Work Regulations 1999; Management of Health and Safety at Work Regulations (NI) 2000
Mobile equipment GB PUWER 1998 NI PUWER 1999Sources: Provision and Use of Work Equipment Regulations 1998; Provision and Use of Work Equipment Regulations (NI) 1999
Traffic routes GB Workplace Regulations 1992 NI Workplace Regulations 1993Sources: Workplace (Health, Safety and Welfare) Regulations 1992; Workplace (Health, Safety and Welfare) Regulations (NI) 1993
Construction when in scope GB CDM 2015 NI CDM 2016Sources: Construction (Design and Management) Regulations 2015; Construction (Design and Management) Regulations (NI) 2016

Identify the operative construction route

For the construction-only case, use the current GB CDM 2015 traffic/vehicle duties; Workplace Regulations regulation 3 excludes most provisions from construction sites. NI requires its corresponding CDM/workplace scope check. A warehouse yard has a different applicable workplace route. HSG144’s practical advice remains useful, but its CDM 2007 law/roles are historical: the current GB 2015/NI 2016 references govern this lesson.

Apply the learning

A raised body will approach an overhead line whose height and status are uncertain.

Decision and explanation

Keep the operation away and obtain the planned utility-informed safe arrangements before work.

Plant can bridge a safe-looking gap as its envelope changes. Do not estimate safe clearance from appearance.

Lesson 14

Pre-use checks and defect control

A safety-critical defect is a hold point. The repair and return-to-service decision must be controlled and recorded.

Where does traffic management fail?

Plans fail when a safe route on paper becomes blocked, unfamiliar, poorly lit or mixed with people and plant in real work.

Watch for damaged barriers, worn markings, repeated reversing, unbriefed deliveries, a marshal in a danger area, vehicle defects, contractor changes and workers taking a shorter unprotected path. A public-road arrangement can fail when signs, pedestrian access or approval no longer match the live scheme.

Treat near misses and workarounds as evidence for redesign. Assign an owner and verify the fix where the movement occurs; a plan revision alone is not a hand-back.

Failure or weak practiceHow it developsWhat good looks like
Painted line onlyPeople and vehicles cross it during pressure.Assess stronger separation and observe the crossing.
Routine reverseConvenience outweighs layout redesign.One-way or drive-through route where practicable.
Unbriefed driverGate is open without a safe waiting process.Booking, hold and concise route instruction.
Blocked walkwayStock or temporary work displaces pedestrians.Clear route, protected alternative and recheck.
Roadworks scheme driftCones or signs move and footway access changes.Competent live inspection and authority escalation.

Visual practice · Pre-use checks and defect control

Actual SHAREsimulate construction model context: A dumper tip is proposed on unverified ground
Actual SHAREsimulate model capture · A dumper tip is proposed on unverified ground. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Where does traffic management fail?

Plans fail when a safe route on paper becomes blocked, unfamiliar, poorly lit or mixed with people and plant in real work. Watch for damaged barriers, worn markings, repeated reversing, unbriefed deliveries, a marshal in a danger area, vehicle defects, contractor changes and workers taking a shorter unprotected path. A public-road arrangement can fail when signs, pedestrian access or approval no longer match the live scheme. Treat near misses and workarounds as evidence for redesign.

How should supervisors decide what traffic controls are needed?

Choose controls by asking who and what could meet, then remove the encounter, separate routes, control the residual movement and verify the result. A supervisor asks whether the movement is necessary, whether the route suits the real vehicle and whether workers, visitors or the public can enter it. If the work reaches a public road or footway, hand design and approval to the competent roadworks route rather than adapting a private-site sketch. Where the answer is unknown, hold the affected movement.

How harm develops in the linked model

Overturn can eject or crush the operator; poor visibility, overload and edge collapse can also injure nearby workers.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should supervisors decide what traffic controls are needed?

Choose controls by asking who and what could meet, then remove the encounter, separate routes, control the residual movement and verify the result.

A supervisor asks whether the movement is necessary, whether the route suits the real vehicle and whether workers, visitors or the public can enter it. If the work reaches a public road or footway, hand design and approval to the competent roadworks route rather than adapting a private-site sketch.

Where the answer is unknown, hold the affected movement. A local plan, a person in high-visibility clothing or a green inspection score cannot substitute for a verified route and required authority decision.

QuestionIf yesIf no or uncertain
Can the journey or reverse be avoided?Remove it or use one-way or drive-through layout.Plan the smallest residual manoeuvre.
Can people and vehicles be separated?Provide direct protected routes and controlled crossings.Hold and redesign or time-separate with competent assessment.
Does the actual vehicle fit and remain stable?Confirm with vehicle and route evidence.Hold for ground, clearance or load assessment.
Are visitors and drivers briefed?Admit to the agreed route.Wait safely and provide instructions.
Does work affect a public road or footway?Use competent scheme and authority route.Keep the work wholly inside the controlled site.
Has anything changed or failed?Reassess, brief and verify before restart.Continue with live checks.

Apply the learning

A pre-use check finds a steering fault but the machine is needed for one more trip.

Decision and explanation

Remove it from use and follow the defect reporting and repair release arrangement.

A safety-critical defect is a hold point. The repair and return-to-service decision must be controlled and recorded.

Lesson 15

Fitness, fatigue and road journeys

Fitness changes during a shift. Work planning must allow safe decisions without pushing people to hide fatigue or impairment.

What changes when a vehicle is driven on the public road for work?

Treat work-road journeys as a connected but distinct risk: plan the journey, check the driver and vehicle, and use road-traffic requirements alongside work-safety management.

HSE distinguishes ordinary commuting from driving for work; HSE and HSENI frame work-road risk around the journey, driver/rider and vehicle. A site traffic plan ends at the gate; it cannot by itself control a public-road journey or unfamiliar receiving site. Sources: HSE driving and riding safely for work, HSENI driving at work, HSE introduction to workplace transport safety.

Work-road journey decisions
Part Decision Evidence or stop trigger
Journey Remove unnecessary trip; plan route, schedule, weather and receiving-site arrival. Late change, unsafe destination or fatigue pressure triggers replanning.Sources: HSE driving and riding safely for work; HSENI driving at work
Driver Check authorisation, fitness and rest for the work journey. Impairment or insufficient rest stops departure.Sources: HSE driving and riding safely for work; HSENI driving at work
Vehicle Check roadworthiness, load and maintenance. Safety-critical defect quarantines vehicle.Sources: HSE driving and riding safely for work; HSENI driving at work

Visual practice · Fitness, fatigue and road journeys

Mini excavator and hire equipment awaiting checks in a UK depot
SHAREhub photographic illustration · Mini excavator and hire equipment awaiting checks in a UK depot. Use the written case for the exercise; this image does not prove a defect or safe system.
What changes when a vehicle is driven on the public road for work?

Treat work-road journeys as a connected but distinct risk: plan the journey, check the driver and vehicle, and use road-traffic requirements alongside work-safety management. HSE distinguishes ordinary commuting from driving for work; HSE and HSENI frame work-road risk around the journey, driver/rider and vehicle. A site traffic plan ends at the gate; it cannot by itself control a public-road journey or unfamiliar receiving site. Sources: HSE driving and riding safely for work, HSENI driving at work, HSE introduction to workplace transport safety.

Plant questions: test the actual control

The answer depends on the live route, machine and jurisdiction. Training, a banksman and a warning alarm each have a defined supporting role. IS DRIVER TRAINING ENOUGH?: No. The manager must make safe site, suitable vehicle and competent driver controls work together.

How harm develops in the linked model

Fatigue, an unsuitable vehicle, an insecure load or a rushed route can injure road users as well as site workers.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Plant questions: test the actual control

The answer depends on the live route, machine and jurisdiction. Training, a banksman and a warning alarm each have a defined supporting role. IS DRIVER TRAINING ENOUGH?: No. The manager must make safe site, suitable vehicle and competent driver controls work together.

CAN A BANKSMAN REPLACE BARRIERS?: A banksman supports a designed system; they do not replace feasible physical segregation. WHAT IF BRAKES OR STEERING FAIL?: Quarantine the vehicle and verify repair before use. A warning or experienced driver cannot resolve the defect. WHAT IF THE ROUTE CHANGES?: Stop affected movement.

Revise, brief and observe the new route before restarting. WHICH LAW APPLIES IN NI?: Northern Ireland has its own 1999 PUWER and workplace-route instrument; GB regulations are not the NI legal route.

Apply the learning

An exhausted driver is asked to complete one final delivery to recover the programme.

Decision and explanation

Stop and arrange a safe response to the fatigue, journey and schedule pressures.

Fitness changes during a shift. Work planning must allow safe decisions without pushing people to hide fatigue or impairment.

Lesson 16

Use records to challenge the layout

Assurance connects the current physical layout, behaviour and records. It must find and resolve divergence, not simply collect documents.

What evidence shows traffic management is controlled?

Keep an accurate route plan, delivery interface, vehicle and driver checks, pedestrian crossings, signaller authorisation, defect holds and change records. Record what the site looked like when the movement occurred.

Evidence itemWhat it should showAssurance question
Site traffic planActual pedestrian, vehicle, loading, crossing and emergency routes.Does it match today’s layout?
Vehicle and driverSuitability, maintenance, task competence and induction.Can this person and vehicle use this route?
Field inspectionBarriers, sightlines, signs, ground, lighting and obstructions.Were defects held and closed?
Change and near missWhy route changed and whether corrective action worked.Was the plan tested in real work?
Roadworks fileApproved competent scheme and authority interface.Does the installed scheme match approval and stay safe?

Visual practice · Use records to challenge the layout

Actual SHAREsimulate construction model context: A delivery crosses the public pavement
Actual SHAREsimulate model capture · A delivery crosses the public pavement. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
What evidence shows traffic management is controlled?

Keep an accurate route plan, delivery interface, vehicle and driver checks, pedestrian crossings, signaller authorisation, defect holds and change records. Record what the site looked like when the movement occurred.

How should traffic management be assured?

Walk routes at busy times and after changes. Check separation, visibility, reversing need, visiting-driver knowledge and whether stopped movements restart only after correction and hand-back.

How harm develops in the linked model

The public may be struck, trapped or forced into the road; visitors may not understand the site traffic system.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should traffic management be assured?

Walk routes at busy times and after changes. Check separation, visibility, reversing need, visiting-driver knowledge and whether stopped movements restart only after correction and hand-back.

Assurance levelWhat to checkWhat good looks like
Point of workRoute, people, driver, vehicle and barriers before movement.A stop is used when the plan fails.
ManagementRepeat defects, changes, near misses and action closure.Control changes are tested, not just filed.
Competent reviewGeometry, public interface or complex plant risk.Assumptions and approvals are verified.
LeadershipResource and risk decisions after unfavourable evidence.Known conflicts do not remain normalised.

Apply the learning

The traffic plan shows a protected walkway where pallets are now stored.

Decision and explanation

Verify actual use, close the conflict and update the plan and briefing before release.

Assurance connects the current physical layout, behaviour and records. It must find and resolve divergence, not simply collect documents.

Lesson 17

Capstone: deliveries meet a changing site

Several individually plausible changes can create a system conflict. A coordinated restart must protect every affected route and person.

How does traffic risk change on a live construction site?

On a live construction project, stop a delivery when the temporary pedestrian route is blocked; restore separation and re-authorise the route before unloading.

BuildOut Ltd is a fictional leisure-centre refurbishment. A telehandler and HGV deliver palletised material while workers use welfare and visitors use a temporary entrance. Rain, stored materials and a moved barrier narrow the pedestrian route. The supervisor checks the route, ground, load, visibility and public boundary before admitting the vehicle; the driver and operator need site-specific instructions.

If the walkway is blocked or the agreed unloading area is unavailable, hold the vehicle at a safe waiting point. Clear or redesign the route, coordinate contractors, brief everyone affected and verify separation before work resumes. After unloading, restore barriers and access, inspect the area and record the changed plan. This is an example, not a certified layout.

IssueWeak responseStronger response
Rain and soft groundKeep timetable and assume plant can use the original route.Check support and traction; hold until the route is suitable.
Barrier moved for palletsAsk pedestrians to take care.Restore a suitable protected route or redesign delivery.
Unbriefed HGV driverWave driver through the gate.Hold at a safe waiting point and brief the route and stop point.
Visitor entrance near plantRely on high-visibility clothing and warnings.Physically protect visitor route and check public interface.

Visual practice · Capstone: deliveries meet a changing site

Workers on a protected walkway separated by continuous guardrails from a site dumper on a UK construction site
SHAREhub photographic illustration · Workers on a protected walkway separated by continuous guardrails from a site dumper on a UK construction site. Use the written case for the exercise; this image does not prove a defect or safe system.
How does traffic risk change on a live construction site?

On a live construction project, stop a delivery when the temporary pedestrian route is blocked; restore separation and re-authorise the route before unloading. BuildOut Ltd is a fictional leisure-centre refurbishment. A telehandler and HGV deliver palletised material while workers use welfare and visitors use a temporary entrance. Rain, stored materials and a moved barrier narrow the pedestrian route.

When should traffic movements stop immediately?

Stop the affected movement when separation, visibility, route condition, vehicle control, emergency access or an applicable road approval is missing or uncertain. A driver who loses sight of a signaller stops immediately, even if the radio still works. Drivers and workers should have a clear stop signal and safe waiting place. Do not ask a marshal to rescue a defective layout.

How harm develops in the linked model

The public may be struck, trapped or forced into the road; visitors may not understand the site traffic system.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

When should traffic movements stop immediately?

Stop the affected movement when separation, visibility, route condition, vehicle control, emergency access or an applicable road approval is missing or uncertain. A driver who loses sight of a signaller stops immediately, even if the radio still works.

Drivers and workers should have a clear stop signal and safe waiting place. Do not ask a marshal to rescue a defective layout. Make the area safe, report the defect, reassess and restart only when an authorised person has verified the changed controls.

For a collision, summon emergency help, prevent further movement and protect responders without moving an injured person unnecessarily. Follow local emergency and reporting arrangements; investigate before returning the route to service.

Stop triggerWhy it mattersAction
Pedestrian barrier or crossing failedPeople can enter the vehicle path.Hold movement, restore separation and verify.
Unknown or obstructed routeDriver may improvise through an exposed area.Hold at a safe point; clear or redesign and brief.
Failed safety-critical vehicle aidVisibility or warning may be inadequate.Quarantine or restrict the vehicle pending competent assessment.
Poor light, weather or groundThe assessed manoeuvre no longer matches conditions.Suspend affected movement and reassess.
Emergency route blockedResponse and evacuation could fail.Stop the obstruction and restore access.
Public-road control unapproved or damagedRoad users may enter a work area.Do not install or continue an unsafe scheme; escalate to scheme owner and authority.
Driver loses sight of signaller, even with radio contactThe signaller is no longer continuously visible in a safe guiding position.Stop immediately; do not reverse again until the visible arrangement is safely reset.

Apply the learning

A fictional East Gate delivery arrives during a pedestrian diversion and a dumper route change.

Decision and explanation

Hold the movement until the whole interface is replanned, separated and briefed.

Several individually plausible changes can create a system conflict. A coordinated restart must protect every affected route and person.

Lesson 18

Make one measurable improvement

An action needs a demonstrable change and a way to verify it. Awareness certificates do not authorise plant operation or traffic design.

Which national legal routes apply?

Choose the instrument for the actual site and task. Great Britain (GB) and Northern Ireland (NI) have separate equipment and workplace-route laws; lifting and construction add scope-specific duties.

Use the legal route with the relevant national regulator’s current guidance, then seek competent site-specific review of amendments, premises and task scope. Do not treat a GB instrument as NI law. Sources: Health and Safety at Work etc. Act 1974, Health and Safety at Work (NI) Order 1978.

National duty routes
Issue Great Britain or England/Wales and Scotland Northern Ireland
General safety and assessment GB 1974 Act and Management Regulations 1999 NI 1978 Order and Management Regulations 2000Sources: Health and Safety at Work etc. Act 1974; Health and Safety at Work (NI) Order 1978; Management of Health and Safety at Work Regulations 1999; Management of Health and Safety at Work Regulations (NI) 2000
Mobile equipment GB PUWER 1998 NI PUWER 1999Sources: Provision and Use of Work Equipment Regulations 1998; Provision and Use of Work Equipment Regulations (NI) 1999
Traffic routes GB Workplace Regulations 1992 NI Workplace Regulations 1993Sources: Workplace (Health, Safety and Welfare) Regulations 1992; Workplace (Health, Safety and Welfare) Regulations (NI) 1993
Construction when in scope GB CDM 2015 NI CDM 2016Sources: Construction (Design and Management) Regulations 2015; Construction (Design and Management) Regulations (NI) 2016

Visual practice · Make one measurable improvement

Actual SHAREsimulate construction model context: A proposed hoarding opening defeats site security
Actual SHAREsimulate model capture · A proposed hoarding opening defeats site security. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Which national legal routes apply?

Which national legal routes apply? Choose the instrument for the actual site and task. Great Britain (GB) and Northern Ireland (NI) have separate equipment and workplace-route laws; lifting and construction add scope-specific duties. Use the legal route with the relevant national regulator’s current guidance, then seek competent site-specific review of amendments, premises and task scope.

Voluntary-standard detail on hold

Specific standard editions, clauses and derived management-system detail are withheld until authorised text, rights and competent technical review are complete. Use applicable law and verified site evidence for current decisions. For general health and safety management, see HSE managing health and safety.

How harm develops in the linked model

Unauthorised people can reach excavations, climb structures or start plant; wind can also destabilise poorly designed hoarding.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Identify the operative construction route

For the construction-only case, use the current GB CDM 2015 traffic/vehicle duties; Workplace Regulations regulation 3 excludes most provisions from construction sites. NI requires its corresponding CDM/workplace scope check. A warehouse yard has a different applicable workplace route. HSG144’s practical advice remains useful, but its CDM 2007 law/roles are historical: the current GB 2015/NI 2016 references govern this lesson.

Voluntary-standard detail on hold

Specific standard editions, clauses and derived management-system detail are withheld until authorised text, rights and competent technical review are complete. Use applicable law and verified site evidence for current decisions.

For general health and safety management, see HSE managing health and safety.

Apply the learning

Your action plan says only remind everyone to be careful around vehicles.

Decision and explanation

Specify an owner, physical control, verification and review trigger for a real route conflict.

An action needs a demonstrable change and a way to verify it. Awareness certificates do not authorise plant operation or traffic design.