SHARE Knowledge Hub

Health and Safety Auditing

Health and safety auditing is a structured assurance activity that checks whether management arrangements are suitable, implemented, effective and improving. A good audit is more than an inspection and more than a document review. In practice, daily control checks, specialist oversight and an independent audit can ask different questions; each needs a clear owner, scope and route for findings. The value of auditing is judgement: knowing what to sample, how to interview, how to grade findings, how to identify system weaknesses and how to make sure actions reduce risk rather than simply close paperwork.

Updated 2026-11-11UK focus

Understanding Health and Safety Auditing

A health and safety audit is a planned, systematic and evidence-based examination of defined criteria and arrangements.

Why this matters at work

An inspection checks a workplace, item, activity or control at a point in time: for example whether a machine guard is fitted or a fire exit is usable. Monitoring tracks performance or exposure over time, using inspections, tests, indicators or surveillance. An investigation examines why an incident or near miss occurred. An audit tests whether the defined management arrangements and controls conform to criteria and are effective across a sample. These activities overlap but answer different questions and should not be represented as substitutes for one another.

Audit evidence should be relevant, sufficient and verifiable against a criterion. Use documents and records to see what was planned and recorded; interviews to learn how people understand and use arrangements; observation to see real work and controls; and technical results to test performance where available. Three sources may disagree, and that disagreement is itself important. For example, a training register says all forklift drivers were trained, a driver reports an unfamiliar route, and observation shows pedestrian conflict: the audit should investigate the system, not dismiss the driver.

How organisations manage this in practice

Define the audit criterion and sample population, then examine tasks and workers representative of the relevant risks, shifts and contractor interfaces. Compare what the files claim with workers’ understanding, the equipment and actual supervision. State what was observed and what was inferred, including limitations of a short visit. A contradiction should prompt further inquiry or an explicit finding rather than be averaged away. Report the control consequence and required action clearly; do not infer whole-site competence or legal compliance from a limited document sample.

Record date, site, process, criterion, source and the specific observation or record reference. Avoid copying personal medical notes, unnecessary names or sensitive details into a broad report. A sample result may need context: one missing inspection might be a local omission; repeated missed checks across shifts may show a management-system failure. A photograph can be useful if site policy, privacy and security allow it, but it needs description and context. A checklist is a prompt, not the evidence itself.

Define exclusions openly. A site audit that does not cover contractor shutdown work, transport yards or night shift should not be presented as whole-site assurance. Include boundaries with landlord, client, suppliers and shared premises. For example, a warehouse audit may cover vehicle/pedestrian segregation but exclude the haulage company's off-site driving; the report must say so. A process audit may follow procurement through installation and maintenance rather than inspect every product. Risk-based scoping should leave a clear reason for what was sampled.

What are the key points for health and safety auditing?

The key points are to audit risk-critical arrangements, use evidence and make findings lead to verified improvement.

What are the key points for health and safety auditing? — part 1 of 3

What are the key points for health and safety auditing? — part 1 of 3. Relationship map from the current topic. Official source supports general method or risk principle; example requires site-specific verification.
Learning point: Relationship map from the current topic. Official source supports general method or risk principle; example requires site-specific verification.
Read the complete visual as text
  1. The key points are to audit risk-critical arrangements, use…: The key points are to audit risk-critical arrangements, use evidence and make findings lead to verified improvement.
  2. Audit the system, not just the file: Documents matter, but field evidence shows whether controls are being used and maintained.
  3. Combine different checks: Use live task checks, specialist oversight and independent audit where the risk and assurance question justify them.

What are the key points for health and safety auditing? — part 2 of 3

What are the key points for health and safety auditing? — part 2 of 3. Relationship map from the current topic. Official source supports general method or risk principle; example requires site-specific verification.
Learning point: Relationship map from the current topic. Official source supports general method or risk principle; example requires site-specific verification.
Read the complete visual as text
  1. Plan sampling around risk: High-risk work, weak signals and significant legal duties deserve deeper sampling than low-risk admin.
  2. Use interviews carefully: Good interviews test understanding, ownership and practical reality without turning into interrogation.

What are the key points for health and safety auditing? — part 3 of 3

What are the key points for health and safety auditing? — part 3 of 3. Relationship map from the current topic. Official source supports general method or risk principle; example requires site-specific verification.
Learning point: Relationship map from the current topic. Official source supports general method or risk principle; example requires site-specific verification.
Read the complete visual as text
  1. Findings should explain risk: A finding should say why the gap matters, not only what document is missing.
  2. Close actions with proof: An action is complete when the risk is reduced and the change is verified, not when a reply is written.

Audit the system, not just the file

Documents matter, but field evidence shows whether controls are being used and maintained.

Combine different checks

Use live task checks, specialist oversight and independent audit where the risk and assurance question justify them.

Plan sampling around risk

High-risk work, weak signals and significant legal duties deserve deeper sampling than low-risk admin.

Use interviews carefully

Good interviews test understanding, ownership and practical reality without turning into interrogation.

Findings should explain risk

A finding should say why the gap matters, not only what document is missing.

Close actions with proof

An action is complete when the risk is reduced and the change is verified, not when a reply is written.

What does health and safety auditing mean?

Health and safety auditing means systematically checking whether the arrangements for managing risk are suitable, implemented and effective.

An audit should follow the line from policy to practice. If a policy says machinery guarding is controlled, the audit should sample the guarding standard, risk assessments, inspection records, maintenance response, training, supervision and actual machines in use. If a policy says contractors are controlled, the audit should test prequalification, induction, permit control, supervision and post-job review.

In a strong assurance model, proactive monitoring of activities and tasks feeds into second-line assurance and then into internal auditing or specialist review. That means supervisor checklist data, permit checks, defect trends and task observations are not just local records; they become evidence that the management system is working or drifting.

Good auditing has a learning mindset. It looks for evidence of drift before harm occurs and helps management decide where controls need stronger design, resources, competence or review.

Audit questionWhat it testsExample evidence
Is the arrangement defined?Policy, standard, risk assessment or procedure exists and is suitable.Controlled procedure and legal register. HSG65 Managing for health and safety
Is it implemented?People are using the arrangement in real work.Observation, interviews and task records. HSG65 Managing for health and safety
Is it effective?The arrangement controls the significant risk.Inspection results, monitoring data and incident trends. HSG65 Managing for health and safety
Is it maintained?Controls, competence and documents remain current.Maintenance, refresher training and review logs. HSG65 Managing for health and safety
Is it improving?Findings and incidents lead to verified improvement.Action tracker and management review minutes. HSG65 Managing for health and safety

How is an audit different from an inspection?

An inspection looks at conditions or activities; an audit tests the management system that should keep those conditions controlled.

A workplace inspection might find a blocked fire exit, damaged cable or missing guard. An audit asks why the system allowed it: unclear ownership, weak inspection frequency, poor defect reporting, no maintenance response, contractor damage, training gap or management review that ignores repeat findings.

Both are useful. The mistake is treating one as the other. A site with perfect inspection sheets may still have poor audit assurance if nobody checks whether findings are closed, trends are reviewed or high-risk areas are sampled.

ActivityPrimary focusUseful outputCommon failure
InspectionCondition, behaviour or control at a point in time.Defects, unsafe conditions, immediate actions.Finds symptoms but not system causes. HSG65 Managing for health and safety
AuditManagement arrangements, evidence, implementation and effectiveness.System findings, ranked actions and improvement priorities.Stays in the office and misses field reality. HSG65 Managing for health and safety
Leadership tourVisible leadership, engagement and early warning signs.Concerns, commitments and resource decisions.Becomes a staged visit with no follow-up. HSG65 Managing for health and safety
Topic reviewOne risk area such as fire, lifting, DSEAR or contractors.Focused evidence and specialist actions.Uses a generic checklist without competence. HSG65 Managing for health and safety
Third-party auditIndependent review against standard, legal expectation or client requirement.External assurance and challenge.Auditor lacks local risk context. HSE audit and reporting guidance

Use a site observation to test whether the management arrangement produces a working control, not only a completed record. HSG65 Managing for health and safety

What types of health and safety audit can be used?

Audit types should be chosen according to the question being asked and the level of assurance needed.

Audit typeUse it whenWhat good evidence includes
System auditTesting the overall management system or ISO-style framework.Policy, objectives, risk process, competence, consultation, audit and review. HSE audit and reporting guidance
Process auditTesting a process such as permit to work, contractor control or incident investigation.Procedure, records, interviews, field sample and action close-out. HSE audit and reporting guidance
Product or output auditChecking whether a defined output meets the standard.Completed risk assessments, permits, training records or inspection reports. HSE audit and reporting guidance
Compliance auditChecking legal or regulator-specific requirements.Legal register, evidence of compliance and responsible owners. HSE audit and reporting guidance
Contractor auditTesting supplier capability and site performance.Prequalification, mobilisation, supervision, RAMS, permits and performance review. HSE audit and reporting guidance
Independent auditAudit by a competent reviewer who can challenge the work being assessed.Audit plan, sampling methodology, evidence trail and management response. HSE audit and reporting guidance

Choose system, process, compliance or technical sampling according to the risk and assurance question. HSG65 Managing for health and safety HSE audit and reporting guidance

How do operating, specialist and independent checks differ?

Operational managers own daily controls. Safety and technical specialists advise, monitor and challenge. An independent audit tests whether those arrangements work and reports findings for management action.

Classify an external provider by the work it performs and its independence: an adviser supporting management is different from an auditor independently checking evidence. HSE guidance calls for proportionate audit and reporting. HSE audit guidance.

RouteAccountability or purposeEvidence to sample
Operational controlOperational management owns the risk and daily controls.Observe live control, defects and supervisor hand-back. HSG65 Managing for health and safety
Specialist oversightRisk, safety or technical functions advise, monitor and challenge management.Review standards, trends, technical checks and escalation. HSG65 Managing for health and safety
Independent auditAn auditor with enough independence from the work tests whether controls and management arrangements are effective.Check audit scope, competence, independence, evidence sample, reporting and tracked findings. HSG65 Managing for health and safety
Other external assuranceAn external reviewer provides an opinion within the scope and mandate agreed for that review.Record scope, commissioning party, competence, limitations and management response. HSE audit and reporting guidance

What are the stages of a good audit?

A good audit moves from scope and planning through evidence gathering, reporting, action close-out and effectiveness review.

StageWhat happensOutput
ProgrammeSet audit topics based on risk, legal duties, incidents, change and previous findings.Annual or rolling audit programme. HSE audit and reporting guidance
NotificationExplain scope, dates, evidence needed and people to involve.Audit notification and evidence request. HSE audit and reporting guidance
PlanningDefine criteria, sampling plan, interview list and site areas.Audit plan and checklist. HSE audit and reporting guidance
Opening meetingConfirm scope, method, timings and communication.Agreed schedule and contacts. HSE audit and reporting guidance
Evidence gatheringSample documents, records, interviews and field observations.Evidence notes and initial findings. HSE audit and reporting guidance
Close-out meetingShare key findings and confirm factual accuracy.Record findings and urgent actions. HSE audit and reporting guidance
ReportIssue ranked findings, evidence, actions and owners.Audit report and action plan. HSE audit and reporting guidance
Follow-upVerify closure and effectiveness.Close-out evidence and management review. HSE audit and reporting guidance

Plan the criteria and sample, gather triangulated evidence, issue findings and verify that actions work later. HSE audit and reporting guidance

How should an audit be planned?

Audit planning should focus on risk, scope, criteria, sampling and the evidence needed to answer the audit question.

The audit plan should say what is being audited and why. A fire audit, contractor audit, COSHH audit and leadership audit need different evidence. Planning should also identify high-risk work, recent incidents, overdue actions, complaints, changes and known weak signals.

Good planning prevents both over-auditing and under-auditing. A small low-risk office may need proportionate checks, while a multi-site construction or process operation needs deeper sampling of significant controls and management review.

PromptGood planning questionExample
ScopeWhat is included and excluded?Audit contractor control from prequalification to site close-out. HSE audit and reporting guidance
CriteriaWhat standard, law, procedure or guidance is used?MHSWR arrangements, company contractor standard and HSG65 principles. HSE audit and reporting guidance
SamplingWhich sites, records, shifts, roles and tasks will be sampled?Two live jobs, three closed actions, five inductions and one night shift. HSE audit and reporting guidance
CompetenceWho is competent to audit this topic?Fire specialist for FRA quality, hygienist for exposure monitoring. HSE audit and reporting guidance
InterfacesWhich teams or contractors affect the control?Procurement, operations, maintenance and site supervision. HSE audit and reporting guidance
EscalationWhat finding needs immediate action?Missing life-safety control, uncontrolled exposure or high-risk permit failure. HSE audit and reporting guidance

Sample high-risk work, previous failures and contractor interfaces before scheduling convenient interviews. HSE audit and reporting guidance

What evidence should an auditor gather?

Auditors should triangulate evidence from documents, records, interviews, observations and performance data.

A document can show intent, a record can show an activity occurred, an observation can show real practice and an interview can show understanding. None is enough alone. The strength of auditing comes from comparing them.

For example, if the training matrix says forklift drivers are trained but field observation shows poor segregation and interviews show confusion about pedestrian routes, the finding is not only a training issue. It may be traffic planning, supervision, layout or leadership attention.

Evidence typeWhat it can evidenceLimit
Policy and procedureIntent, responsibilities and standards.May not reflect real work. HSG65 Managing for health and safety
Risk assessments and permitsHazards, controls and authorisation decisions.May be copied or poorly briefed. HSG65 Managing for health and safety
Training and competence recordsPeople attended or were assessed.Attendance does not prove practical competence. HSG65 Managing for health and safety
Maintenance and inspection recordsControls are checked and defects managed.Records may miss field condition or repeat defects. HSG65 Managing for health and safety
InterviewsUnderstanding, ownership, reporting culture and practical barriers.People may describe ideal work if trust is low. HSG65 Managing for health and safety
Field observationActual control use, behaviour and conditions.May only show one time and one shift. HSG65 Managing for health and safety
Performance dataTrends, repeat findings and weak signals.Data may be under-reported or poorly classified. HSG65 Managing for health and safety

Compare documents with workers’ accounts and the physical state of safeguards at live work. HSG65 Managing for health and safety HSE audit and reporting guidance

How can the hierarchy of controls turn audit findings into effective workplace risk controls?

ERICPD is used here as a planning mnemonic. The linked HSE five-level hierarchy is the official source for the order and relative reliability of controls; the two labels are not identical.

Remove or redesign the hazardous transfer or fume-generating task first; the study or audit verifies decisions and evidence, not the barrier by itself.

How do ERICPD and the five-level hierarchy change the real control? — part 1 of 2

How do ERICPD and the five-level hierarchy change the real control? — part 1 of 2. Evidence map: these are the current topic’s explanation and conditions. Illustrative control selection; specialist design and task assessment are required.
Learning point: Evidence map: these are the current topic’s explanation and conditions. Illustrative control selection; specialist design and task assessment are required.
Read the complete visual as text
  1. ERICPD is used here as a planning mnemonic. The…: ERICPD is used here as a planning mnemonic. The linked HSE five-level hierarchy is the official source for the order and relative reliability of controls; the two labels are not identical.
  2. Remove or redesign the hazardous transfer or fume-generating task…: Remove or redesign the hazardous transfer or fume-generating task first; the study or audit verifies decisions and evidence, not the barrier by itself.

How do ERICPD and the five-level hierarchy change the real control? — part 2 of 2

How do ERICPD and the five-level hierarchy change the real control? — part 2 of 2. Evidence map: these are the current topic’s explanation and conditions. Illustrative control selection; specialist design and task assessment are required.
Learning point: Evidence map: these are the current topic’s explanation and conditions. Illustrative control selection; specialist design and task assessment are required.
Read the complete visual as text
  1. The auditor samples welding-fume control on a fabrication line.…: The auditor samples welding-fume control on a fabrication line. All welding fume can cause lung cancer; the audit tests whether source reduction and local exhaust actually work, but is not itself a physical control. HSE welding-fume control
  2. ERICPD is a six-stage planning aid; the HSE five…: ERICPD is a six-stage planning aid; the HSE five levels separate substitution, engineering, administration and residual PPE. Isolate normally maps to engineered separation, Control can include physical or administrative measures, and Discipline sustains controls through maintenance and learning. HSE five-level hierarchy HSE five-level hierarchy

The auditor samples welding-fume control on a fabrication line. All welding fume can cause lung cancer; the audit tests whether source reduction and local exhaust actually work, but is not itself a physical control. HSE welding-fume control

ERICPD is a six-stage planning aid; the HSE five levels separate substitution, engineering, administration and residual PPE. Isolate normally maps to engineered separation, Control can include physical or administrative measures, and Discipline sustains controls through maintenance and learning. HSE five-level hierarchy HSE five-level hierarchy

How should management verify controls for this task?

For welding-fume extraction failure during structural fabrication, the management check should start with a real control decision: Check whether preformed or mechanically fastened assemblies remove the weld for this bracket. Name the person who will test it, keep evidence from the actual work, and reopen the assessment when the failure condition in the hierarchy table occurs. HSE management-system guidance.

A review should compare the planned control with what workers and supervisors can use in practice. Record the defect, owner, interim protection, verification and next review trigger so that a policy statement or certificate does not stand in for a working control.

How should audit interviews be carried out?

Audit interviews should test understanding and practical reality in a fair, calm and evidence-led way.

Good interviews are not traps. They ask people to explain how work is done, what can go wrong, what controls they rely on, what makes the job difficult and what they would do if a control was missing. The aim is to understand the system, not to catch a worker out.

Interview evidence should be handled carefully. One comment may be a useful weak signal, but the auditor should test it against records, observation and other interviews before drawing conclusions.

PromptWhat it revealsFollow-up evidence
Show me how this task is started.Whether procedure and real work align.Observation and work instruction. HSE audit and reporting guidance
What would make you stop this job?Stop-work authority and escalation culture.Training, supervisor expectations and permits. HSE audit and reporting guidance
Which control matters most here?Whether people understand critical controls.Risk assessment and briefing. HSE audit and reporting guidance
What happens when equipment is defective?Defect reporting and maintenance response.Defect log and repair records. HSE audit and reporting guidance
What changed recently?Whether management of change is understood.Change record and revised assessment. HSE audit and reporting guidance
What gets in the way of doing it safely?System barriers such as time pressure, tools, layout or staffing.Action tracker and management review. HSE audit and reporting guidance

Ask how the worker responds to a defect and compare the answer with the actual task and record. HSE audit and reporting guidance

How should audit findings be graded and written?

Findings should be written so the reader understands the evidence, risk significance and required improvement.

A finding that says 'procedure not followed' may be accurate but incomplete. A stronger finding explains why: the procedure is outdated, equipment layout changed, supervision is inconsistent or workload makes compliance unrealistic. That helps management fix the system rather than blame the symptom.

Grading should be consistent and risk-based. A missing signature on a low-risk form is not the same as an untested fire alarm, absent isolation or repeated failure to close RIDDOR investigation actions.

Finding elementWeak wordingStronger wording
EvidenceSome records missing.Three of ten sampled LEV user checks were missing for high-dust tasks in the joinery area. HSG65 Managing for health and safety
RequirementProcedure not followed.Company COSHH standard requires daily LEV user checks before dusty work starts. HSG65 Managing for health and safety
RiskNon-compliance.Missing check records leave uncertainty about whether checks occurred and whether controls performed adequately. Establish the facts and actual capture performance; assess any defect and required immediate protection. Health-surveillance decisions follow the separate exposure/health criteria. HSG65 Managing for health and safety
CauseStaff forgot.Supervisors had not assigned ownership and the check form was not located at the point of use. HSG65 Managing for health and safety
ActionRetrain staff.Assign ownership, move check to task start point, brief supervisors and verify completion for four weeks. HSG65 Managing for health and safety
Close-outComplete.Action closed after field verification showed checks completed and defects escalated. HSG65 Managing for health and safety

State the observed evidence, failed requirement or control, significance, owner and corrective action. HSG65 Managing for health and safety

What do good audit findings look like in practice?

Good audit findings connect what was seen, what was sampled, why it matters, what system weakness exists and what evidence will prove improvement.

Worked audit finding examples — part 1 of 2

Worked audit finding examples — part 1 of 2. Compare the named situations, controls and evidence together. Official source supports general method or risk principle; example requires site-specific verification.
Learning point: Compare the named situations, controls and evidence together. Official source supports general method or risk principle; example requires site-specific verification.
Read the complete visual as text
  1. Two fire doors in a hotel corridor did not close fully.: Evidence sampled: Field observation, fire door register, last monthly check and maintenance log. Finding wording: Two sampled fire doors protecting the main escape corridor failed to self-close and the defect register did not show escalation or interim control. Grading: Major Root or system weakness: Fire door inspection results were recorded but not risk-ranked or linked to maintenance priority. Action required: Repair doors, risk assess interim arrangements, revise defect escalation and brief duty managers. Verification evidence: Repair certificate, updated fire door register, supervisor check and re-sample at next audit.
  2. COSHH assessment said LEV was used, but operators dry-swept dust at shift end.: Evidence sampled: COSHH assessment, cleaning procedure, observation, interviews and LEV inspection record. Finding wording: Dry sweeping was observed in the workshop despite COSHH controls requiring dust capture or damp cleaning for respirable dust tasks. Grading: Major Root or system weakness: The cleaning method had not been risk assessed and supervisors were checking production quality rather than exposure controls. Action required: Replace dry sweeping with controlled cleaning method, brief workers, assign supervisor verification and update COSHH task assessment. Verification evidence: Revised assessment, cleaning equipment issued, worker briefing record and follow-up observation.

Worked audit finding examples — part 2 of 2

Worked audit finding examples — part 2 of 2. Compare the named situations, controls and evidence together. Official source supports general method or risk principle; example requires site-specific verification.
Learning point: Compare the named situations, controls and evidence together. Official source supports general method or risk principle; example requires site-specific verification.
Read the complete visual as text
  1. Forklift-pedestrian segregation markings were faded near dispatch.: Evidence sampled: Traffic risk assessment, site plan, CCTV sample, inspection record and driver interviews. Finding wording: Pedestrian route definition at dispatch was unclear and inspection records had not identified deterioration in segregation markings. Grading: Moderate Root or system weakness: Inspection checklist focused on vehicle defects and missed workplace transport layout controls. Action required: Re-mark route, add traffic layout checks to inspection, brief dispatch team and review near-miss reports. Verification evidence: Photographic evidence, updated checklist, toolbox record and one-month near-miss trend review.
  2. Contractor RAMS were accepted without site-specific lifting details.: Evidence sampled: Three contractor packs, lift plan, induction record and supervisor interview. Finding wording: Contractor lifting documentation was accepted without confirming load weights, exclusion zones, ground conditions or appointed person review. Grading: Major Root or system weakness: Procurement and site supervision standards did not define what competent lifting documentation must include before mobilisation. Action required: Set lifting document acceptance criteria, train supervisors, hold contractor start until reviewed and sample next three lifts. Verification evidence: Revised contractor rule, reviewed lift plans, supervisor competence record and field verification.

New auditors often either write too little or write a long narrative that hides the decision. A strong finding is short enough for a manager to understand, but detailed enough for an action owner to fix the cause and for a later reviewer to verify closure.

The examples below show how a finding moves from observation to evidence, grading, root or system weakness, action and verification. The point is not to produce perfect wording; it is to make the risk and improvement route clear.

ObservationEvidence sampledFinding wordingGradingRoot or system weaknessAction requiredVerification evidence
Two fire doors in a hotel corridor did not close fully.Field observation, fire door register, last monthly check and maintenance log.Two sampled fire doors protecting the main escape corridor failed to self-close and the defect register did not show escalation or interim control.MajorFire door inspection results were recorded but not risk-ranked or linked to maintenance priority.Repair doors, risk assess interim arrangements, revise defect escalation and brief duty managers.Repair certificate, updated fire door register, supervisor check and re-sample at next audit. HSG65 Managing for health and safety
COSHH assessment said LEV was used, but operators dry-swept dust at shift end.COSHH assessment, cleaning procedure, observation, interviews and LEV inspection record.Dry sweeping was observed in the workshop despite COSHH controls requiring dust capture or damp cleaning for respirable dust tasks.MajorThe cleaning method had not been risk assessed and supervisors were checking production quality rather than exposure controls.Replace dry sweeping with controlled cleaning method, brief workers, assign supervisor verification and update COSHH task assessment.Revised assessment, cleaning equipment issued, worker briefing record and follow-up observation. HSG65 Managing for health and safety
Forklift-pedestrian segregation markings were faded near dispatch.Traffic risk assessment, site plan, CCTV sample, inspection record and driver interviews.Pedestrian route definition at dispatch was unclear and inspection records had not identified deterioration in segregation markings.ModerateInspection checklist focused on vehicle defects and missed workplace transport layout controls.Re-mark route, add traffic layout checks to inspection, brief dispatch team and review near-miss reports.Photographic evidence, updated checklist, toolbox record and one-month near-miss trend review. HSG65 Managing for health and safety
Contractor RAMS were accepted without site-specific lifting details.Three contractor packs, lift plan, induction record and supervisor interview.Contractor lifting documentation was accepted without confirming load weights, exclusion zones, ground conditions or appointed person review.MajorProcurement and site supervision standards did not define what competent lifting documentation must include before mobilisation.Set lifting document acceptance criteria, train supervisors, hold contractor start until reviewed and sample next three lifts.Revised contractor rule, reviewed lift plans, supervisor competence record and field verification. HSG65 Managing for health and safety

A useful finding distinguishes a missing form from a failed barrier that exposes people. HSG65 Managing for health and safety

What should a health and safety audit report include?

An audit report should clearly describe scope, evidence, findings, risk ranking, actions, owners, timescales and follow-up.

Report elementPurposeGood practice
Executive summaryShows senior leaders the main risk themes.Use plain language and highlight high-risk issues. HSE audit and reporting guidance
Scope and criteriaDefines what was audited and against what standard.State exclusions and limitations. HSE audit and reporting guidance
Method and sampleExplains how evidence was gathered.List sites, records, interviews and observations sampled. HSE audit and reporting guidance
Positive findingsRecognises effective controls and good practice.Use evidence, not generic praise. HSE audit and reporting guidance
Non-conformities or findingsDescribes gaps and risk significance.Use clear evidence and requirement. HSE audit and reporting guidance
ActionsTurns findings into improvement.Name owner, due date, priority and verification need. HSE audit and reporting guidance
Follow-upConfirms closure and effectiveness.Include re-audit or management review route. HSE audit and reporting guidance

Report sampling limits and risk-critical open actions so leaders can make a defensible hold or resource decision. HSE audit and reporting guidance

How should audit actions be closed and verified?

Audit actions should be closed with evidence that the control has improved and the risk has reduced.

A common weakness is closing actions because a document was updated, an email was sent or a toolbox talk was delivered. Those may be part of the response, but they do not prove the problem is fixed. Verification should sample whether the changed arrangement works in the field.

For high-risk findings, action close-out should include effectiveness review. If a guarding audit found defeated interlocks, the closure evidence should include repaired guards, supervision, maintenance response, operator briefing and later field checks.

Closure typeWeak closureBetter closure
Document updateProcedure revised.Procedure revised, briefed, used in field and sampled after four weeks. HSG65 Managing for health and safety
Training actionToolbox talk delivered.Competence checked through observation and questions during task. HSG65 Managing for health and safety
Maintenance actionDefect reported.Defect repaired, retested and recurrence trend reviewed. HSG65 Managing for health and safety
Management actionDiscussed at meeting.Resource decision made, owner assigned and progress tracked. HSG65 Managing for health and safety
Contractor actionContractor told.Contractor standard updated, supervisors briefed and next job audited. HSG65 Managing for health and safety

Revisit the live task to confirm that the corrective action controls the hazard under normal pressure. HSG65 Managing for health and safety

How does this topic align with ISO 45001?

Use these examples to connect the relevant clauses to your own occupational health and safety management system. For each clause, identify the person responsible, the control in use and the evidence that it works.

Scroll across the table to read all four columns.

ISO 45001 clause alignment for Health and Safety Auditing
ISO 45001 clauseHow it appliesWhat to put in placeHow to verify it works
9.2.1 Internal auditsInternal audit checks whether the system meets the organisation’s own arrangements and ISO 45001 requirements, and whether those arrangements are working.Follow a sampled lifting operation from the approved plan to the actual equipment, crew and shared routes. Check the documents, ask the people involved and observe what happens.Findings link each conclusion to its audit criteria and evidence. The sample shows whether critical controls were applied where the lift took place.
9.2.2 Internal audit programmeThe audit programme determines what gets audited, when and by whom. Operational importance and earlier findings help set priorities.Prioritise lifting operations with complicated interfaces or repeated findings. Set scope and criteria, select auditors who can work objectively, and share findings with relevant managers and workers or their representatives where applicable.Audit schedules explain the priorities and records show which sites and lifts were sampled. Findings reach the people who own the actions and those affected by them.
10.2 Incidents and corrective actionWhen an audit finds a failure to meet a requirement, corrective action addresses why it happened and checks whether it could happen elsewhere.Use the work-control route to address any immediate problem with the lift. Investigate why the site used different equipment or arrangements, then correct the planning or handover process where needed.A later sample tests whether similar lifts now match the approved plan. Retain the evidence used to verify effectiveness before closing the action.

Selected applications of ISO 45001:2018 with Amendment 1:2024. Use the current standard for a full assessment and check the legal duties that apply to the work and location.

ISO 45001:2018 · 2024 climate action amendment · ISO 45002 implementation guidance · ISO technical committee clause FAQ

How does the method transfer to other work?

The method asks what could fail and who is exposed; the strongest feasible physical control changes with the task.

A sector label alone cannot choose a study method, audit sample or safeguard. Define design intent, people, material, route and stop condition with the local owner. HSE risk-assessment steps HSENI five steps to risk assessment

SectorTask and harm routeStrongest feasible control and checkHold point
ManufacturingWelding fume reaches welders and adjacent workers.Check cold joining or lower-fume process, then live local capture.Hold the weld on failed capture. HSE welding-fume control HSG65 Managing for health and safety
ConstructionTemporary fuel storage and refill can release vapour to an ignition source.Check inventory reduction, separation and ignition control.Hold refill on unassessed layout or vapour release. HSE DSEAR guidance HSG65 Managing for health and safety
HospitalityCleaning chemical concentrate is diluted by room staff with skin or inhalation exposure.Check suitable low-exposure product or closed dilution and actual COSHH task sheet.Hold on unidentified product or uncontrolled splash. HSE service and retail COSHH task advice HSG65 Managing for health and safety
LogisticsHGV reversing near pickers can strike or crush a pedestrian.Check a segregated route and safe loading-bay layout in the field.Stop vehicle movement if separation fails. HSE separating pedestrians and vehicles HSG65 Managing for health and safety

How does health and safety auditing support NEBOSH National General Certificate study?

Learners should understand audit purpose, audit stages, audit types, internal and external audits and the difference between audit and inspection.

For a study answer, a strong response should describe auditing as management system assurance. It should explain that an audit uses evidence to check whether arrangements are suitable, implemented and effective. It should also distinguish inspections from audits and describe stages from notification through to report and follow-up.

In scenario questions, avoid writing 'carry out an audit' as a vague recommendation. State what will be audited, what evidence will be sampled, who should be interviewed, what standard applies and how actions will be verified.

PromptStrong answer includesWeak answer
Define auditStructured review of management arrangements and evidence of effectiveness.Checking paperwork. HSG65 Managing for health and safety
Audit v inspectionInspection checks conditions; audit checks the system behind them.Uses the words interchangeably. HSG65 Managing for health and safety
Audit stagesPlan, notify, gather evidence, interview, observe, report and follow up.Only mentions report. HSG65 Managing for health and safety
TypesSystem, process, product, internal, external and compliance audits.Only says internal/external. HSG65 Managing for health and safety
EvidenceDocuments, records, observations, interviews and trend data.Relies on documents alone. HSG65 Managing for health and safety

What can each role demonstrate before making decisions?

Competence is shown by observed scenario or evidence decisions, a named assessor and a record; attendance alone does not authorise a hazardous task.

Use awareness, supervised practice, specialist review and reassessment in proportion to the role. A workshop or audit finding must be translated into a working control with a named owner. HSE audit and reporting guidance HSG65 Managing for health and safety

RoleLearning and practical demonstrationAssessor and recordReassess when
Operator or frontline workerIdentify wrong line-up, alarm bypass or poor capture; demonstrate stop and report.Supervisor observes live task and records understanding.Change, near miss or failed barrier. HSG65 Managing for health and safety
Supervisor and action ownerTest pre-start hold, action wording and field close-out.Manager samples decision and signed hand-back.Overdue action or changed conditions. HSG65 Managing for health and safety
Study participant or auditorApply method to a realistic deviation or evidence sample.Facilitator or lead auditor observes contribution and records scope.New method or topic beyond competence. HSG65 Managing for health and safety
Facilitator, lead auditor or technical specialistLead scenario challenge, independence and limits; refer relief, SIL or exposure issues to specialists.Peer review of study or audit record and technical decision.Weak findings, missed scenario or technical change. HSG65 Managing for health and safety
Manager or designerFund source controls and accept only documented, justified residual decisions.Director or accountable owner reviews design, resources and field evidence.Repeated control failure or major change. HSG65 Managing for health and safety

What warning signs show auditing is not adding value?

Warning signs appear when audits count paperwork, avoid hard conversations and close actions without proving risk reduction.

Warning signHow it weakens assuranceAction
Same checklist every yearEmerging risks, change and weak signals are missed.Rebuild audit plan around risk profile and recent evidence. HSG65 Managing for health and safety
No field samplingDocuments look good while work is uncontrolled.Require observation and interview samples. HSG65 Managing for health and safety
Findings lack risk rankingMinor admin gaps compete with serious control failures.Use severity, likelihood and control criticality to rank. HSG65 Managing for health and safety
Actions close by emailNo proof that controls changed.Require verification evidence. HSG65 Managing for health and safety
Auditors lack competenceSpecialist gaps are missed or overclaimed.Match auditor competence to topic risk. HSG65 Managing for health and safety
Management does not review themesRepeat findings continue across sites.Trend audit outputs and assign strategic actions. HSG65 Managing for health and safety

What do the acronyms and key terms mean?

Acronyms should be understood before they are used in assessments, briefings, audits or learning answers.

AcronymMeaningPlain-English use
PDCAPlan, Do, Check, ActManagement cycle used by HSE and many management systems.
NGCNEBOSH National General CertificateQualification route where auditing may be studied.
ISOInternational Organization for StandardizationBody that publishes ISO 45001 and other standards.
OH&SOccupational Health and SafetyCommon term used in ISO 45001.
RIDDORReporting of Injuries, Diseases and Dangerous Occurrences RegulationsReportable-event duties differ between GB and Northern Ireland; check the local instrument.
ERICPDEliminate, Reduce, Isolate, Control, PPE, DisciplineSix-stage control planning aid, not legislation. HSE five-level hierarchy

Which Crownway Fuels documents support this topic?

Open an editable document, read the preview, or find its place in the Crownway hierarchy. 6 resources relate to this page.

Fictional Crownway Fuels examples for English forecourts, with a separate illustrative bulk terminal. Check site applicability, permissions and actual controls before adapting any document for use.

Audit legal evaluation and continual improvement policy (6)
  • Audit legal evaluation and continual improvement policy (CWF-POL-AUDIT · Completed fictional example)

    Set company expectations, responsibilities and resources for audit legal evaluation and continual improvement.
    Read preview · Download DOCX · Show in hierarchy

  • Audit legal evaluation and continual improvement procedure (CWF-PRO-AUDIT · Completed fictional example)

    Explain who does what, in what sequence, the control rationale, evidence, escalation and safe restart conditions.
    Read preview · Download DOCX · Show in hierarchy

  • Independent audit and legal evaluation programme (CWF-PLN-AUDIT-01 · Completed fictional example)

    Provide the site/task-specific independent audit and legal evaluation programme and retain its controlled output.
    Read preview · Download DOCX · Show in hierarchy

  • Management system and legal evidence audit (CWF-AUD-AUDIT-01 · Blank editable master)

    Provide the site/task-specific management system and legal evidence audit and retain its controlled output.
    Read preview · Download DOCX · Show in hierarchy

  • Audit finding corrective action and verification record (CWF-FRM-AUDIT-01 · Blank editable master)

    Provide the site/task-specific audit finding corrective action and verification record and retain its controlled output.
    Read preview · Download DOCX · Show in hierarchy

  • Annual review and improvement priorities record (CWF-FRM-AUDIT-02 · Blank editable master)

    Provide the site/task-specific annual review and improvement priorities record and retain its controlled output.
    Read preview · Download DOCX · Show in hierarchy

Open the full Crownway library

Documents to download

Download editable resources from the SHAREhub environment to support your work. Working forms and spreadsheet input areas are blank. Reports, plans, guides, briefings, procedures and policies contain completed worked example content to adapt.

Return to SHARE home