A near miss is an unplanned event that could have harmed someone but did not. Report it promptly, make the situation safe, investigate the controls that failed and verify corrective action. Some specified high-potential events are legally reportable dangerous occurrences; most everyday near misses are managed internally.
Updated 2026-10-22Great Britain and Northern Ireland
Understanding Near miss reporting and learning
A near miss is an event that did not cause injury or ill health on this occasion but had the potential to do so.
Why this matters at work
Property damage or environmental release can occur without personal injury. Record the actual outcome and potential for harm separately. A damaged rack and a narrowly missed worker can both be true; coding the case only as 'damage' may hide the near-miss mechanism, while coding it only as 'near miss' may hide repair and environmental duties.
Separate the event's actual severity from credible worst consequence and from probability of recurrence. Record each dimension so a high-potential, no-harm event can be prioritised without distorting the accident count. Repeated lower-consequence events may still require deeper investigation because they signal a recurring control failure.
How organisations manage this in practice
Ask what each barrier was designed to do, its test and maintenance history, who could detect a failure, and what independent evidence shows its condition at the time. An alarm that sounded only after entry did not prevent entry, though it may have helped recovery. A human last-minute dodge is not an engineered separation control.
Prioritise high-potential and repeated mechanisms. Ask whether a known defect appeared in earlier near misses and why the action failed to prevent recurrence. Review overdue critical actions and whether interim controls are still credible. Bring procurement and engineering leaders into decisions that a site cannot solve alone.
Look at time and place clustering, work phase, shift, contractor, equipment model and recent change. Compare near misses with defect reports, maintenance work orders, inspections and actual accidents. A pattern can emerge across systems even when each database shows only one or two cases.
Use interim controls when permanent redesign needs time. Give them an owner, end date and daily or shift check. If interim protection cannot credibly prevent recurrence, suspend the activity until a reliable control is in place.
Include task purpose, equipment identity, people present, layout, lighting, weather, instructions, alarms, maintenance state and any change from normal operation where relevant. Record an absence only if it was checked. 'No guard seen' is not the same as proof that no guard was fitted before the event.
Who should report and act on a near miss?
Anyone who sees a credible near miss should raise it; supervisors make the area safe, and managers own investigation, corrective action and any statutory reporting decision.
Terms used in the work decisions below: Health and Safety Executive (HSE); Health and Safety Executive for Northern Ireland (HSENI); Great Britain (GB); Northern Ireland (NI). Apply each source within its stated location and subject.
A worker can describe what happened without proving a root cause or deciding if it meets RIDDOR. Contractors and visitors need a usable route too. The supervisor should identify who was exposed and what might happen if the event repeats. A competent manager or adviser then checks the correct legal reporting category for the work location. Leaders should make reporting safe and worthwhile by closing the loop with the people who raised it.
From near miss to verified prevention
Make safe
Stop exposure and protect the scene without creating another hazard.
Preserve facts
Record what failed, who could have been harmed and which barriers were absent.
Classify separately
The responsible person checks GB or NI reporting criteria while internal learning continues.
Verify change
Name an action owner, observe the repaired barrier and close only with evidence.
Use the Near miss reporting and learning guidance to recognise relevant hazards, understand the precautions and identify when to stop, report a problem or ask for competent support.
Supervisors and managers
Use the task examples and control checks to plan work, brief the team, check implementation and assign improvements with owners and follow-up.
Safety, health, risk and assurance professionals
Use the explanations, sources and operational examples to develop assessments, audits and control verification. Check the actual scope and jurisdiction before applying a duty.
Learners, trainers and organisational decision makers
Use the definitions and examples to connect theory with workplace decisions, build briefings and ask informed questions. This page does not certify competence or authorise work.
What are the first decisions after a near miss?
Stop the unsafe activity, protect people, preserve relevant evidence, tell the responsible manager and check whether the event is a reportable dangerous occurrence.
What are the first decisions after a near miss?
Learning point: Relationship map from the current topic. Read the linked sources within their subject and jurisdiction.
Stop the unsafe activity, protect people, preserve relevant evidence,…: Stop the unsafe activity, protect people, preserve relevant evidence, tell the responsible manager and check whether the event is a reportable dangerous occurrence.
Do not wait for an injury to apply controls.…: Do not wait for an injury to apply controls. If equipment or a structure may fail again, isolate it and establish a safe boundary. Record the time, location, task, people and conditions, while avoiding assumptions about blame. Preserve relevant items, photographs and records without putting anyone at risk. The dutyholder should compare the facts with the current GB or NI RIDDOR schedule; report promptly when a specified category is met.
Best-practice guide · six simple steps
Best-practice guide: Near miss reporting and learning
Start with the key actions, then explore value, a workplace example, harm, stronger controls and further help. Choose a step or use Previous and Next; the guide does not advance automatically.
What are the first decisions after a near miss?
Avoid / redesign
Dropped-load event: design out an overhead lift above people where feasible; planner confirms the replacement task.
Control the task
Physically separate the load path and use suitable retained lifting equipment; competent lead verifies exclusion and equipment.
Verify before release
Signed lift method; hold any new overhead route.
Stop the unsafe activity, protect people, preserve relevant evidence, tell the responsible manager and check whether the event is a reportable dangerous occurrence. A near miss is an unplanned event that could have harmed someone but did not.
Apply it: Which part of this plan would you check at the workface before authorising the task?
Turn near miss reporting and learning knowledge into a decision
Change at source
Dropped-load event: design out an overhead lift above people where feasible; planner confirms the replacement task.
Make it observable
Signed lift method; hold any new overhead route.
Keep useful evidence
Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
A near miss is an unplanned event that could have harmed someone but did not. Report it promptly, make the situation safe, investigate the controls that failed and verify corrective action. Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
Apply it: What evidence would show that the change improves this task, rather than only completing a record?
A contractor hoists a heavy unit across a shared loading area in a logistics site.
Act
The supervisor stops the lift, checks the worker, isolates the area and preserves the attachment, equipment and work pack.
Hold / review
The lift remains stopped while the equipment and pedestrian separation are unverified.
The lifting lead and investigator test attachment suitability, inspection, load weight, plan, route and why a person could enter the fall zone. They record uncertainties rather than assuming operator fault. The site redesigns the pedestrian route and exclusion, replaces defective equipment if found, revises the plan and observes a trial lift.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed?
Choose controls for near miss reporting and learning
Elimination
Dropped-load event: design out an overhead lift above people where feasible; planner confirms the replacement task.
Substitution
Use ground-level mechanical transfer where practicable; lifting lead tests load stability and new vehicle risks.
Engineering
Physically separate the load path and use suitable retained lifting equipment; competent lead verifies exclusion and equipment.
Administrative
Use a competent lift plan, supervision, communication and access control; supervisor checks the live setup.
PPE and assurance
Use task PPE for residual hazards and investigate departures; a hard hat cannot control a major falling load.
Elimination: dropped-load event: design out an overhead lift above people where feasible; planner confirms the replacement task. Substitution: Use ground-level mechanical transfer where practicable; lifting lead tests load stability and new vehicle risks. Engineering: Physically separate the load path and use suitable retained lifting equipment; competent lead verifies exclusion and equipment. Administrative: Use a competent lift plan, supervision, communication and access control; supervisor checks the live setup. PPE and assurance: Use task PPE for residual hazards and investigate departures; a hard hat cannot control a major falling load. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?
Use the full near miss reporting and learning lesson
Official guidance
HSE HSG245 investigation guidance
Official guidance
HSE dangerous-occurrence guidance
Task decision
Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status.
Apply it: Which official source and full-topic section will you use to resolve the next decision?
Keep one card or the full set for social sharing, team briefings and learning. Each PDF contains a workplace image with separate learning notes. Read the full topic for sources and further detail.
Read all six steps as text
1. What are the first decisions after a near miss?
Stop the unsafe activity, protect people, preserve relevant evidence, tell the responsible manager and check whether the event is a reportable dangerous occurrence.
Avoid / redesign: Dropped-load event: design out an overhead lift above people where feasible; planner confirms the replacement task.
Control the task: Physically separate the load path and use suitable retained lifting equipment; competent lead verifies exclusion and equipment.
Verify before release: Signed lift method; hold any new overhead route.
Stop the unsafe activity, protect people, preserve relevant evidence, tell the responsible manager and check whether the event is a reportable dangerous occurrence. A near miss is an unplanned event that could have harmed someone but did not.
Apply it: Which part of this plan would you check at the workface before authorising the task?
2. Turn near miss reporting and learning knowledge into a decision
Use the evidence to improve the actual work arrangement.
Change at source: Dropped-load event: design out an overhead lift above people where feasible; planner confirms the replacement task.
Make it observable: Signed lift method; hold any new overhead route.
Keep useful evidence: Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
A near miss is an unplanned event that could have harmed someone but did not. Report it promptly, make the situation safe, investigate the controls that failed and verify corrective action. Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
Apply it: What evidence would show that the change improves this task, rather than only completing a record?
Example: a practical application of the existing topic lesson.
Setting: A contractor hoists a heavy unit across a shared loading area in a logistics site.
Act: The supervisor stops the lift, checks the worker, isolates the area and preserves the attachment, equipment and work pack.
Hold / review: The lift remains stopped while the equipment and pedestrian separation are unverified.
The lifting lead and investigator test attachment suitability, inspection, load weight, plan, route and why a person could enter the fall zone. They record uncertainties rather than assuming operator fault. The site redesigns the pedestrian route and exclusion, replaces defective equipment if found, revises the plan and observes a trial lift.
Apply it: At which point would you hold this example, and what evidence would allow it to proceed?
4. What distinguishes a near miss from a dangerous occurrence?
Connect the task, the route to the person and the control that can fail.
Source / exposure: Near miss is a broad learning term; a RIDDOR dangerous occurrence is a specific event defined in law, whether or not someone was hurt.
Possible consequence: A pallet that nearly strikes a worker is a near miss worth internal investigation.
Control failure: It is not automatically a RIDDOR dangerous occurrence.
Near miss is a broad learning term; a RIDDOR dangerous occurrence is a specific event defined in law, whether or not someone was hurt.
Apply it: Who could be exposed, including other trades, cleaners, maintainers and people nearby?
5. Choose controls for near miss reporting and learning
Start with the stronger practicable options and verify their effect.
Elimination: Dropped-load event: design out an overhead lift above people where feasible; planner confirms the replacement task.
Substitution: Use ground-level mechanical transfer where practicable; lifting lead tests load stability and new vehicle risks.
Engineering: Physically separate the load path and use suitable retained lifting equipment; competent lead verifies exclusion and equipment.
Administrative: Use a competent lift plan, supervision, communication and access control; supervisor checks the live setup.
PPE and assurance: Use task PPE for residual hazards and investigate departures; a hard hat cannot control a major falling load.
Elimination: dropped-load event: design out an overhead lift above people where feasible; planner confirms the replacement task. Substitution: Use ground-level mechanical transfer where practicable; lifting lead tests load stability and new vehicle risks. Engineering: Physically separate the load path and use suitable retained lifting equipment; competent lead verifies exclusion and equipment. Administrative: Use a competent lift plan, supervision, communication and access control; supervisor checks the live setup. PPE and assurance: Use task PPE for residual hazards and investigate departures; a hard hat cannot control a major falling load. Read the full control table for qualifications, ownership and verification. Use the actual task and applicable jurisdiction; existing technical approval remains unchanged.
Apply it: Which stronger option can be used here, and who will verify it before accepting the remaining risk?
6. Use the full near miss reporting and learning lesson
Follow the official sources below and retain the task-specific evidence.
Official guidance: HSE HSG245 investigation guidance
Official guidance: HSE dangerous-occurrence guidance
Task decision: Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
Use the full topic for the decision points, practical examples, detailed control tables and source scope. HSE guidance applies to Great Britain; use HSENI for the Northern Ireland route and the source’s stated jurisdiction. A simplified guide does not change the page’s technical-review or approval status.
Apply it: Which official source and full-topic section will you use to resolve the next decision?
Simplified learning guide. Use the full topic and the actual work arrangements; existing technical-review and approval statuses still apply.
Do not wait for an injury to apply controls. If equipment or a structure may fail again, isolate it and establish a safe boundary. Record the time, location, task, people and conditions, while avoiding assumptions about blame. Preserve relevant items, photographs and records without putting anyone at risk. The dutyholder should compare the facts with the current GB or NI RIDDOR schedule; report promptly when a specified category is met.
One failed lift, two possible outcomes
The same failed lift can leave no one injured or seriously harm someone. Investigate the control failure and potential consequences in either case, while checking statutory reporting as a separate decision.
Illustrative UK workplace scene. Read the practical checks below for responsibilities, evidence and limits. Download image · Download smaller image
Make safe
Stop the affected activity and protect people from the remaining load, plant and exclusion-zone hazards. Rescue and emergency needs take priority.
Preserve evidence
Keep relevant equipment, records and witness accounts without creating further risk or altering the scene unnecessarily.
Reconstruct the path
Establish attachment, load movement, people’s positions and the work sequence; distinguish verified facts from assumptions.
Failed controls
Examine lift planning, equipment suitability, exclusion, supervision and management conditions. A fortunate outcome does not demonstrate effective control.
Statutory category separate
The responsible person checks the current GB or NI reporting requirements against the facts. Some dangerous occurrences are reportable without injury; “near miss” is not itself the legal category.
Correct and verify
Assign actions and check their effectiveness before the affected work resumes. Share learning with other tasks that rely on the same controls.
Where facts are uncertain, record the uncertainty and obtain competent reporting advice promptly. Do not use an injury/no-injury shortcut to decide legal reportability.
What distinguishes a near miss from a dangerous occurrence?
Near miss is a broad learning term; a RIDDOR dangerous occurrence is a specific event defined in law, whether or not someone was hurt.
A pallet that nearly strikes a worker is a near miss worth internal investigation. It is not automatically a RIDDOR dangerous occurrence. A qualifying collapse or failure of lifting equipment may meet a specified legal category even without injury. The judgement turns on the exact event, schedule wording and location, not a local “high potential” label. GB RIDDOR 2013 and NI RIDDOR 1997 have different lists and reporting rules, so do not copy an answer across jurisdictions.
An unsafe condition is a hazard observation before an event; a near miss is an event in which harm was narrowly avoided. Both deserve action, but the distinction helps investigation and reporting.
How should an internal report and triage work?
A simple report captures the event and immediate safeguard, then a named person assesses potential severity, recurrence and the need for statutory reporting.
Allow workers to report by a route they can actually use during the shift. Capture what was seen and where, the task and equipment, who might have been affected, what prevented harm and what remains unsafe. A supervisor acknowledges the report and decides the immediate hold. The triage owner checks the RIDDOR category, coordinates any regulatory report, assigns an investigator and sets a review time. Protect personal data and share learning without naming individuals unnecessarily.
If facts change, revisit the reporting decision. Record the reason and source used when concluding that an event does or does not meet a legal category.
How does a missed near miss become an injury?
A weak signal becomes harm when the underlying hazard and failed barrier stay in place for the next worker or shift.
A dropped load with no injury may reveal a damaged lifting attachment, an unsuitable lift plan or an exclusion zone that existed only on paper. If the report closes as “operator error”, the next lift can put another person in the same path. A slip without injury may reveal contamination, drainage or cleaning failures. The investigation should trace source, exposure route, barrier, affected people and credible outcome, including the conditions that allowed the event.
How should the investigation find useful causes?
Collect reliable facts, reconstruct the sequence, test why barriers failed and choose changes that prevent recurrence.
HSE HSG245 describes gathering information, analysing it, identifying controls and making an action plan. Speak with those involved promptly and fairly; compare accounts with work instructions, maintenance, training, layout and supervision. Ask why the situation made the action possible rather than ending at an individual mistake. Scale the depth of investigation to the credible harm and likelihood, and include the right technical specialist for equipment or process failures.
Record uncertainty. A missing camera angle or damaged component is a reason to qualify a conclusion, not to invent certainty. The investigation should produce testable control changes and an owner.
Investigation methods and worked examples
How can Fishbone and Five Whys help explore causes?
A fishbone, also called a cause-and-effect or Ishikawa diagram, places the event at its head. The main bones group possible contributors; smaller branches explore what led to each one. Categories are prompts to investigate, not findings.
Fishbone: explore the wider picture
Use it when several things may have contributed. Start with categories such as people, equipment, methods, materials, environment and management; rename them to suit the work. Add causes and subcauses without forcing a single chain.
Ask what led to a specific explanation. Branch when there is another reason, and stop where the evidence runs out. Five is a guide, not a target. Use the two methods together to examine a broad picture and its individual paths.
Define what happened, including the task, place and sequence. Keep the event separate from assumptions about why.
Gather accounts from people involved and add several possible explanations. Explore work conditions, equipment and management arrangements as well as individual actions.
Record supporting and contradictory evidence for each explanation. Keep untested ideas separate from accepted findings; add an open question where evidence is missing.
Review immediate, underlying and root causes from the evidence. A category, the final card or the depth of a branch does not decide the cause level.
Link actions to the supported causes, assign an owner and date, then check implementation and whether the action prevents recurrence.
Compare the worked examples
The two BuildOut reports examine the same invented excavator-arm/scaffold incident: 18 explanations and six actions. Their evidence references are fictional teaching records.
BuildOut fishbone
Six cause categories with subcauses, evidence checks and actions · 24 pages.
How can the hierarchy of controls turn near-miss findings into stronger risk controls?
Remove or reduce the hazard and make the work physically safer before relying on reminders, retraining or discipline.
Use the HSE hierarchy to remove or substitute the hazard where feasible, then use engineering separation, administrative measures and PPE for residual exposure. Keep each selected control effective through inspection, maintenance and worker feedback. The task-specific table below records the decision and stop point.
A good action states what will change, who owns it, when it will be ready and how its effectiveness will be checked. “Remind staff to take care” is not enough for a foreseeable high-consequence event.
HSE prioritises eliminating and substituting hazards before engineering controls, administrative controls and PPE, as explained in its five-level hierarchy of controls. SHARE uses ERICPD as a task-planning prompt: Eliminate; Reduce, including substitution; Isolate through engineered separation; Control with other engineered or administrative measures; PPE; and Discipline, meaning continued verification and maintenance. ERICPD is not a sixth HSE level or a separate legal duty. In the dropped-load example, ground-level transfer is a substitution; limiting access is administrative and does not replace a physically safe load route.
The table is a dropped-load corrective-action example; a near miss is an event, so its controls depend on the actual hazard. HSE lift-planning guidance supports checking the load path and exclusion before work resumes.
How can the ERICPD hierarchy of controls turn near-miss findings into stronger risk controls?
Worked activity: BuildOut dropped-load response
Activity and exposure
A contractor hoists a heavy unit across a shared loading area in a logistics site. A slinging attachment slips and the load falls near a picker. No one is injured.
Before work
The supervisor stops the lift, checks the worker, isolates the area and preserves the attachment, equipment and work pack. The near miss is recorded promptly.
During the activity
The lifting lead and investigator test attachment suitability, inspection, load weight, plan, route and why a person could enter the fall zone. They record uncertainties rather than assuming operator fault.
Hold or stop
The lift remains stopped while the equipment and pedestrian separation are unverified. In GB, a failed sling or accessory alone is excluded from the lifting-equipment failure category; the responsible person still checks other outcomes and the NI rules, which also exclude a failed sling alone from the lifting-equipment dangerous-occurrence category.
Hand-back and release
The site redesigns the pedestrian route and exclusion, replaces defective equipment if found, revises the plan and observes a trial lift. A manager authorises restart only after the controls work.
Evidence to retain
Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
A contractor hoists a heavy unit across a shared loading area in a logistics site. A slinging attachment slips and the load falls near a picker. No one is injured.
Before work
The supervisor stops the lift, checks the worker, isolates the area and preserves the attachment, equipment and work pack. The near miss is recorded promptly.
During the activity
The lifting lead and investigator test attachment suitability, inspection, load weight, plan, route and why a person could enter the fall zone. They record uncertainties rather than assuming operator fault.
Hold or stop
The lift remains stopped while the equipment and pedestrian separation are unverified. In GB, a failed sling or accessory alone is excluded from the lifting-equipment failure category; the responsible person still checks other outcomes and the NI rules, which also exclude a failed sling alone from the lifting-equipment dangerous-occurrence category.
Hand-back and release
The site redesigns the pedestrian route and exclusion, replaces defective equipment if found, revises the plan and observes a trial lift. A manager authorises restart only after the controls work.
Evidence to retain
Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
Investigate departures and verify closure of the lifting controls.
Read the practical categories separately: elimination removes the hazardous task/source; substitution replaces it with a suitable safer alternative; physical separation, containment and capture are engineering decisions. Duration/access/briefing are administrative measures, PPE covers residual exposure, and continued inspection, maintenance and verified action closure sustain the controls. Exposure monitoring or dosimetry measures exposure rather than protecting a person. The detailed text and records below distinguish these decisions; an overview illustration is not task authorisation.
When is external reporting required in GB or NI?
Only specified injuries, diseases and dangerous occurrences meet RIDDOR criteria. The responsible person must use the current law and regulator route for the event location.
In Great Britain, the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 2013 specify reportable dangerous occurrences in Schedule 2. HSE warns that not all near misses are reportable. In Northern Ireland, the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (Northern Ireland) 1997 apply as amended; HSENI explains that dangerous occurrences are reportable. An ordinary internal near-miss scheme should be broader than the legal minimum. HSE dangerous-occurrence guidance and the NI regulations support the separate routes.
Do not assume that a GB list or reporting time applies in NI. If an event may meet a category, preserve facts, use the relevant official guidance and make the required report through the responsible person. Internal learning and regulator notification are separate decisions.
Place
Event
Reporting decision
GB
Pallet nearly strikes a worker
Record and investigate internally; not automatically a RIDDOR dangerous occurrence. Sources: HSE.
NI
Pallet nearly strikes a worker
Record and investigate internally; compare with NI specified categories if facts change. Sources: HSENI.
GB
A load-bearing part of lifting equipment mechanically fails
Compare with GB Schedule 2; a sling or other lifting accessory alone is excluded from this category. Sources: HSE.
NI
A lifting sling or a load-bearing equipment part fails
HSENI also excludes sling/accessory failure alone from this dangerous-occurrence category; a load-bearing equipment failure may be reportable. Check other categories and injuries. Sources: HSENI.
GB
Hazard is noticed before an event
Control and record the hazard; observation alone is not a dangerous occurrence. Sources: HSE.
NI
Hazard is noticed before an event
Control and record the hazard; check whether any specified event actually occurred. Sources: HSENI.
Qualifying dangerous occurrence: notify without delay. Ensure the report reaches the enforcing authority within ten days; ten days is not permission to postpone notification or wait for investigation closure. For GB use the relevant HSE online dangerous-occurrence route in HSE incident reporting times; HSE’s telephone service is for fatalities and specified worker injuries, not every dangerous occurrence. For NI use HSENI accident reporting and NI2508 and the NI2508 process. Record who notified, the submission/reference and deadline alongside the separate safeguarding and investigation actions. Preserve the lifting-accessory exclusion and decide the actual event against the appropriate jurisdiction’s category.
How should closure be verified?
Check in the field that the corrective action interrupts the original harm route, then confirm it remains effective across shifts and contractors.
Evidence can include a repaired guard or segregated route, inspection result, revised drawing, observed task, contractor briefing and a follow-up sampling date. The investigator should compare the new condition with the failed barrier and credible outcome. A manager checks overdue high-risk actions and repeats. Close only when the barrier works, not when an email says it is complete. If a new test fails, reinstate the hold and escalate.
How could BuildOut Ltd learn from a dropped load?
In this logistics example, a suspended load misses a worker because they step back; the task stays stopped until the lift plan and pedestrian separation are verified.
BuildOut dropped-load response — part 1 of 3
Learning point: Worked evidence map for this worked example. Responsible owner: Site manager with a competent lifting lead. Read the linked parts together; emergency protection takes priority over routine work and records.
1. Task and setting: A contractor hoists a heavy unit across a shared loading area in a logistics site. A slinging attachment slips and the load falls near a picker. No one is injured.
2. People and prerequisites: The picker, lift team and nearby workers may be affected. The supervisor needs a lift plan, equipment records, a pedestrian boundary and a reporting route available to contractors.
3. Before the task: The supervisor stops the lift, checks the worker, isolates the area and preserves the attachment, equipment and work pack. The near miss is recorded promptly.
BuildOut dropped-load response — part 2 of 3
Learning point: Worked evidence map for this worked example. Responsible owner: Site manager with a competent lifting lead. Read the linked parts together; emergency protection takes priority over routine work and records.
1. Check during work: The lifting lead and investigator test attachment suitability, inspection, load weight, plan, route and why a person could enter the fall zone. They record uncertainties rather than assuming operator fault.
2. Stop, hold or refer: The lift remains stopped while the equipment and pedestrian separation are unverified. In GB, a failed sling or accessory alone is excluded from the lifting-equipment failure category; the responsible person still checks other outcomes and the NI rules, which also exclude a failed sling alone from the lifting-equipment dangerous-occurrence category.
BuildOut dropped-load response — part 3 of 3
Learning point: Worked evidence map for this worked example. Responsible owner: Site manager with a competent lifting lead. Read the linked parts together; emergency protection takes priority over routine work and records.
1. Completion and hand-back: The site redesigns the pedestrian route and exclusion, replaces defective equipment if found, revises the plan and observes a trial lift. A manager authorises restart only after the controls work.
2. Retained evidence: Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
BuildOut dropped-load response
Task, material and setting: A contractor hoists a heavy unit across a shared loading area in a logistics site. A slinging attachment slips and the load falls near a picker. No one is injured.
People and prerequisites: The picker, lift team and nearby workers may be affected. The supervisor needs a lift plan, equipment records, a pedestrian boundary and a reporting route available to contractors.
Before: The supervisor stops the lift, checks the worker, isolates the area and preserves the attachment, equipment and work pack. The near miss is recorded promptly.
During: The lifting lead and investigator test attachment suitability, inspection, load weight, plan, route and why a person could enter the fall zone. They record uncertainties rather than assuming operator fault.
Hold or stop: The lift remains stopped while the equipment and pedestrian separation are unverified. In GB, a failed sling or accessory alone is excluded from the lifting-equipment failure category; the responsible person still checks other outcomes and the NI rules, which also exclude a failed sling alone from the lifting-equipment dangerous-occurrence category.
Completion and hand-back: The site redesigns the pedestrian route and exclusion, replaces defective equipment if found, revises the plan and observes a trial lift. A manager authorises restart only after the controls work.
Evidence: Retain the report, photographs and equipment record, GB or NI RIDDOR decision, investigation, action owners, trial-lift observation, shift briefing and authorised restart.
Transfer to a process release: A solvent line sprays inside an empty enclosure without injury. The supervisor isolates the line, records who could have entered and preserves the equipment state; the reporting lead checks the actual event facts against the specified GB or NI dangerous-occurrence categories rather than calling every release reportable. Engineering repairs and tests the barrier, and the manager checks the revised isolation and hand-back before restart. Internal learning proceeds even if no statutory category is met. HSE dangerous-occurrence categories and HSENI reporting route support the location-specific triage.
What competence does a reporting system need?
People need different skills for recognition, immediate control, investigation, legal triage and action assurance.
New starters and contractors should demonstrate how to raise a report and stop an unsafe task. Frontline supervisors should practise safeguarding, initial fact capture and fair conversations. Investigators need causal analysis and evidence-handling skills appropriate to the risk. Managers must challenge weak actions, allocate resources and test completion. The responsible person or specialist adviser must be able to apply the correct GB or NI RIDDOR criteria. Record practical demonstrations and review competence after a complex event, error or process change; a generic course certificate alone is insufficient.
Role
Learning and decision
Evidence and reassessment
Worker or contractor
Recognise an event, stop unsafe work and make an accessible report.
Can report a realistic example; refresh after route change.
Supervisor
Make safe, capture facts fairly and escalate potential severity.
Observed scenario and field hold; revisit after a missed escalation.
Investigator
Reconstruct sequence and test barrier causes.
Sample investigation with credible corrective actions.
Manager or legal triage owner
Apply GB or NI RIDDOR criteria and verify corrective action.
Recorded category decision and field closure check.
How should leaders use near-miss trends?
Use reports to identify repeated failed barriers and verify improvements, while keeping the reporting route trusted.
HSE explains that a formal health and safety management system is optional. The employer must still plan, control, check and improve the measures for this task. Check completed actions in the field, review repeat barrier failures alongside reporting participation, and reopen the investigation if a barrier still fails.
What questions arise about near misses?
Report and safeguard first; a competent owner can then decide legal classification and investigation depth.
Should I report a near miss if nobody was hurt?
Yes, use the organisation’s reporting route. The event may reveal a barrier failure before someone is harmed.
Are all near misses reportable under RIDDOR?
No. Only specified dangerous occurrences and other listed outcomes are legally reportable. Check the relevant GB or NI category.
Can a supervisor close it after reminding the team?
Only if the evidence shows the actual hazard and failed barrier have been addressed. High-consequence events often require physical or system changes and a field check.
Will more reports mean the site is becoming less safe?
Not necessarily. Counts depend on trust and reporting access. Examine severity, barrier patterns and verified actions alongside the number of reports.
How would you investigate a reversing near miss without stopping at blame?
Reconstruct the work and failed barriers, then choose actions that reduce the chance of another vehicle-person conflict.
How would you investigate a reversing near miss without stopping at blame? — part 1 of 2
Learning point: Evidence map: these are the current topic’s explanation and conditions. Original illustrative decisions supported by the listed official sources. HSE technical guidance has Great Britain scope; Northern Ireland duties use the page's separate NI routes. Clinical fitness, exact instrument settings and task acceptance require competent advice.
Reconstruct the work and failed barriers, then choose actions…: Reconstruct the work and failed barriers, then choose actions that reduce the chance of another vehicle-person conflict.
In an illustrative delivery-yard event, a reversing vehicle nearly…: In an illustrative delivery-yard event, a reversing vehicle nearly contacts a visiting technician who has followed an informal shortcut. First make the area safe, preserve useful facts and support the people involved. Record the vehicle movement, sight lines, route, timing, signage, access arrangements and what each person understood. Do not decide the cause from the label 'carelessness'. See HSE HSG245 investigation guidance .
Ask why the technician could enter the vehicle path:…: Ask why the technician could enter the vehicle path: was a separated route available, did delivery timing block it, had contractors been told how to reach the work area, and could the driver see the conflict? Distinguish evidence from a hypothesis and check each against the physical layout and accounts. A barrier that happened to prevent injury is worth understanding as well as the barrier that failed. See HSE five-level hierarchy .
How would you investigate a reversing near miss without stopping at blame? — part 2 of 2
Learning point: Evidence map: these are the current topic’s explanation and conditions. Original illustrative decisions supported by the listed official sources. HSE technical guidance has Great Britain scope; Northern Ireland duties use the page's separate NI routes. Clinical fitness, exact instrument settings and task acceptance require competent advice.
The manager first considers removing the conflicting movement, changing…: The manager first considers removing the conflicting movement, changing delivery access or providing effective physical separation. Briefing and observation support the redesigned system, but a reminder does not make the original conflict disappear. Name the designer or operations owner, record the feasible options and specify a field check under actual deliveries before closing the action. The example is a learning investigation, not a finding about a real driver or site. See HSE five-level hierarchy .
Decision basis: HSE HSG245 investigation guidance . HSE five-level…: Decision basis: HSE HSG245 investigation guidance . HSE five-level hierarchy . The scenario and suggested records are illustrative; apply the source within its stated jurisdiction and the assessed work.
In an illustrative delivery-yard event, a reversing vehicle nearly contacts a visiting technician who has followed an informal shortcut. First make the area safe, preserve useful facts and support the people involved. Record the vehicle movement, sight lines, route, timing, signage, access arrangements and what each person understood. Do not decide the cause from the label 'carelessness'. See HSE HSG245 investigation guidance.
Ask why the technician could enter the vehicle path: was a separated route available, did delivery timing block it, had contractors been told how to reach the work area, and could the driver see the conflict? Distinguish evidence from a hypothesis and check each against the physical layout and accounts. A barrier that happened to prevent injury is worth understanding as well as the barrier that failed. See HSE five-level hierarchy.
The manager first considers removing the conflicting movement, changing delivery access or providing effective physical separation. Briefing and observation support the redesigned system, but a reminder does not make the original conflict disappear. Name the designer or operations owner, record the feasible options and specify a field check under actual deliveries before closing the action. The example is a learning investigation, not a finding about a real driver or site. See HSE five-level hierarchy.
How should urgency, reporting and action closure be distinguished?
A serious potential outcome can require immediate control even when the event does not meet a statutory reporting category.
Internal triage asks what credible harm could have followed and whether a critical barrier is missing now. Legal reportability asks whether the actual event meets the applicable definition in GB or NI. Action closure asks whether the chosen change works. A local 'high potential' label does not answer the legal question, and the absence of a reportable category does not justify leaving an unsafe layout in use. See HSE RIDDOR dangerous occurrences.
Assign the responsible person to check the appropriate official category and timescale against the facts. Preserve the reason for that decision separately from the corrective-action record. For closure, observe the new arrangement with the affected workers and contractors, including a foreseeable busy or obstructed condition; record any remaining conflict and its owner. See HSENI RIDDOR NI booklet.
Look for prompt reporting, proportionate triage, stronger barriers and feedback, rather than treating a falling report count as success by itself.
Learning check: a department meets a target of zero near-miss reports after a manager criticises every reporter. The learner should question participation and trust, not assume that exposure to harm has vanished. Check whether contractors, temporary staff and different shifts can use the reporting route and receive a useful response. See HSE HSG245 investigation guidance.
Learning check: the action says 'retrain driver' and is closed because attendance is recorded. The supervisor should ask what causal barrier the training repairs, whether the person can demonstrate the required task and whether the physical conflict remains. Completion of an activity is different from evidence of an effective control. See HSE management-system guidance.
Provide the reporter with a proportionate explanation of the decision and changes, protecting personal information. Sample repeat events and overdue critical actions alongside reporting participation. Managers should be able to show a traceable path from event, through evidence and ownership, to a stronger barrier and a verified review. See HSE management-system guidance.
NI RIDDOR 1997 and reporting route. Additional source context: HSENI HSENI accident reporting and NI2508 Northern Ireland NI reporting route and responsible-person submission; use NI dangerous-occurrence criteria.
SHARE planning prompt; Discipline means maintaining controls, not blame.
Which documents can I download for this topic?
Download editable resources from the SHAREhub environment to support your work. Working forms and spreadsheet input areas are blank. Reports, plans, guides, briefings, procedures and policies contain completed worked example content to adapt.
Near miss: event, evidence and action record
For workers, supervisors, investigators and the responsible reporting person. Prioritise emergency assistance and effective safeguarding, then capture what happened. All actual entries are blank. Use the separate investigation report to see how evidence can support findings and action verification. This record is not a statutory report or permission to restart.
Blank form or working record · DOCX · 26 KB · v1.0
Completed teaching report | case NM-R7 | Review state: partial action closure, remaining restrictions open. Northmere Archive Services, its 29 workers, all events, dates, records and findings are independently invented. No real person, evidence, signature or operational approval is represented. The report demonstrates reasoning; actual work needs its own investigation and competent assessment.
Completed practical guide with blank working record · DOCX · 28 KB · v1.0