Noise, vibration and radiation in construction · learning reader

Free training · Approx. 2h–2h 50m · estimated self-paced learning, including activities and assessment.

Public teaching is free without an account. A free learner account is required for confirmed LMS assessment, completion and certificate records. See the full course outline and access routes.

Teaching and applied cases for accessible study. The interactive course records assessed completion.

Lesson 1

Look for exposure across the whole shift

Assess representative exposure across all relevant tasks, people and conditions.

Read the workface decision

Physical agents can cause harm without a dramatic incident. The working day may combine noise, vibrating tools, vehicle shocks and specialist radiation activities. A useful exposure picture follows people and tasks, including nearby trades and changing locations. Do not assume that a short observation or a supplier's equipment figure represents the entire day's personal exposure.

Visual practice · Look for exposure across the whole shift

Sound level measurement at a UK industrial workplace
SHAREhub photographic illustration · Sound level measurement at a UK industrial workplace. Use the written case for the exercise; this image does not prove a defect or safe system.
Read the workface decision

Physical agents can cause harm without a dramatic incident. The working day may combine noise, vibrating tools, vehicle shocks and specialist radiation activities. A useful exposure picture follows people and tasks, including nearby trades and changing locations. Do not assume that a short observation or a supplier's equipment figure represents the entire day's personal exposure.

How is a defensible exposure estimate built?

Map tasks and variation, use reliable representative data, calculate full-shift exposure and document uncertainty and review triggers. Sample normal and foreseeable worst operating modes, not only the quietest shift. Record meter type, calibration, location, duration and workers.

See the actual construction-model example

At this workface, cutting and mobile plant create two connected problems. Repeated sound exposure can permanently harm hearing, while the same noise can hide an alarm or prevent a driver and signaller from understanding each other. A person wearing hearing protection still needs effective communication and warning arrangements. The assessment must consider everyone exposed across a representative day, including nearby trades and intermittent high-level events, rather than only the machine operator during a short demonstration.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How is a defensible exposure estimate built?

Map tasks and variation, use reliable representative data, calculate full-shift exposure and document uncertainty and review triggers.

Sample normal and foreseeable worst operating modes, not only the quietest shift. Record meter type, calibration, location, duration and workers. Supplier sound-power or emission information cannot be copied straight into personal exposure; verify installed use. Weekly exposure can help where days vary, but assess a peak separately. If the estimate straddles an action value, improve the data and use protective controls while resolving uncertainty. Sources: HSE noise risk assessment, HSE L108 noise guidance (third edition, 2021).

So far as practicable, assess interactions between noise and ototoxic substances used at work, and between noise and vibration, as required by regulation 5(3)(c) in both jurisdictions. Record relevant chemical/process co-exposures and vibration, link the COSHH/vibration assessments and seek competent technical or occupational-health advice where needed. Do not infer causation from a worker’s medication list or place personal medical details in a noise survey.

Weekly averaging requires marked variation, a reasoned recorded justification and worker consultation; it must not increase risk or conceal a peak. See the companion calculator’s weekly-suitability explanation and L108 paragraphs 28–29 rather than assuming every variable day qualifies.

See the actual construction-model example

At this workface, cutting and mobile plant create two connected problems. Repeated sound exposure can permanently harm hearing, while the same noise can hide an alarm or prevent a driver and signaller from understanding each other. A person wearing hearing protection still needs effective communication and warning arrangements. The assessment must consider everyone exposed across a representative day, including nearby trades and intermittent high-level events, rather than only the machine operator during a short demonstration.

Choose quieter methods and equipment and address avoidable noise at source through maintenance, suitable tooling, damping, isolation or engineered barriers where appropriate. Then assess the remaining exposure and provide properly selected hearing protection and a hearing-conservation arrangement where required. A protector’s packaging rating is not the protection achieved by every wearer, especially with poor fit, incompatible PPE or frequent removal to hear instructions. A phone application or conversation test can indicate concern, but does not replace a competent assessment where one is needed. Communication and traffic protection should be designed so people do not have to remove protection or step into a vehicle route to understand a warning.

Evidence to establish at the workface

Eliminate unnecessary noisy stages or select quieter processes and suitable equipment; include noise performance in procurement and planning rather than accept it as an unavoidable site condition.

Apply the learning

A shift plan lists a ten-minute demonstration but omits several hours of cutting and nearby plant noise.

Decision and explanation

Assess representative exposure across all relevant tasks, people and conditions.

Physical agents can cause harm without a dramatic incident. The working day may combine noise, vibrating tools, vehicle shocks and specialist radiation activities. A useful exposure picture follows people and tasks, including nearby trades and changing locations. Do not assume that a short observation or a supplier's equipment figure represents the entire day's personal exposure.

Lesson 2

Understand hearing damage and warning loss

Reduce the noise risk and verify communication and warnings rather than waiting for symptoms.

Read the workface decision

Noise can damage hearing and produce tinnitus, while also obscuring speech, alarms and signals needed for immediate safety. These are related but different consequences. A person may not recognise gradual loss early enough to use symptoms as a safe limit. Protect nearby people as well as operators, and investigate masking of warnings as a workface control failure.

Close view of a healthy adult external ear showing its rim, folds, bowl and lobule.View full detail ↗
The outer ear in context

Locate the visible outer ear before considering the hearing pathway and the lesson’s noise-control decisions.

Locate the outer ear, then connect the lesson to the hearing pathway. What would reduce noise exposure at source?

educational illustration · healthy anatomy; enlarged details and teaching colours.

Visual practice · Understand hearing damage and warning loss

Actual SHAREsimulate construction model context: Noise masks warnings beside the plant route
Actual SHAREsimulate model capture · Noise masks warnings beside the plant route. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Investigate 1: Mobile plant

Plant is visible beside the work area. The case says noise masks a warning: investigate both the noise controls and the means of coordinating movement. A still capture cannot tell you what an alarm sounds like.

Investigate 2: Workstation

The work position is visible. Ask how noise is controlled at source and how the task is separated from people, rather than assume hearing protection alone resolves the stated warning problem.

Investigate 3: Worker route beside the activity

The model shows people and a route near the activity. Test how a worker receives essential instructions when the fictional task makes speech and an alarm difficult to hear. Verify the actual communication arrangement.

Read the workface decision

Noise can damage hearing and produce tinnitus, while also obscuring speech, alarms and signals needed for immediate safety. These are related but different consequences. A person may not recognise gradual loss early enough to use symptoms as a safe limit. Protect nearby people as well as operators, and investigate masking of warnings as a workface control failure.

What is damaged in NIHL?

Excessive sound can injure inner-ear sensory hair cells and related auditory structures, producing sensorineural loss that cannot be reversed by ordinary rest. Source basis: nidirect hearing-loss guidance · HSE noise worker advice. The pattern is often gradual with repeated exposure, especially trouble hearing speech in background noise; a very intense impulse may cause acute injury.

Evidence to establish at the workface

Maintain tools and plant, isolate or damp suitable sources and use effective separation or acoustic controls without defeating machine guards, ventilation or safe access.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What is damaged in NIHL?

Excessive sound can injure inner-ear sensory hair cells and related auditory structures, producing sensorineural loss that cannot be reversed by ordinary rest.

The pattern is often gradual with repeated exposure, especially trouble hearing speech in background noise; a very intense impulse may cause acute injury. Tinnitus can occur with or without an obvious audiometric loss. Other conditions, medication and age can contribute to hearing difficulty, so a clinician interprets an individual result. nidirect hearing-loss guidance explains the hair-cell mechanism and other possible causes. Sources: HSE noise worker advice.

Evidence to establish at the workface

Maintain tools and plant, isolate or damp suitable sources and use effective separation or acoustic controls without defeating machine guards, ventilation or safe access.

Apply the learning

Workers turn up radios because cutting masks speech, while the crew assumes hearing damage will be obvious immediately.

Decision and explanation

Reduce the noise risk and verify communication and warnings rather than waiting for symptoms.

Noise can damage hearing and produce tinnitus, while also obscuring speech, alarms and signals needed for immediate safety. These are related but different consequences. A person may not recognise gradual loss early enough to use symptoms as a safe limit. Protect nearby people as well as operators, and investigate masking of warnings as a workface control failure.

Lesson 3

Distinguish daily exposure and peaks

Assess representative daily exposure and the separate peak risk using suitable competent information.

Read the workface decision

Noise assessment needs suitable data for the decision and an understanding of uncertainty. Peak events and accumulated exposure are not interchangeable. Equipment emission information can help compare tools but may not describe the operator's position or surrounding sources. When the result affects control decisions and the evidence is weak, obtain competent advice rather than reporting a precise but unsupported number.

Visual practice · Distinguish daily exposure and peaks

Sound level measurement at a UK industrial workplace
SHAREhub photographic illustration · Sound level measurement at a UK industrial workplace. Use the written case for the exercise; this image does not prove a defect or safe system.
Read the workface decision

Noise assessment needs suitable data for the decision and an understanding of uncertainty. Peak events and accumulated exposure are not interchangeable. Equipment emission information can help compare tools but may not describe the operator's position or surrounding sources. When the result affects control decisions and the evidence is weak, obtain competent advice rather than reporting a precise but unsupported number.

How do daily and peak exposure differ?

Estimate representative personal exposure across all tasks and compare the separate C-weighted peak, using competent measurements when the decision is uncertain. Record machine mode, position, operating time, other noise sources, nearby workers and variation across days. A supplier emission figure is a starting point, not personal exposure at this workstation.

Evidence to establish at the workface

Assess representative daily or appropriate weekly exposure and separate peaks for exposed people. Select hearing protection for the actual task, fit and PPE compatibility and provide required hearing surveillance.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How do daily and peak exposure differ?

Estimate representative personal exposure across all tasks and compare the separate C-weighted peak, using competent measurements when the decision is uncertain.

Record machine mode, position, operating time, other noise sources, nearby workers and variation across days. A supplier emission figure is a starting point, not personal exposure at this workstation. Weekly averaging may be relevant where daily exposure varies; it does not erase a high peak. HSE sets the representative-estimate requirement. Sources: HSE noise employer duties.

Evidence to establish at the workface

Assess representative daily or appropriate weekly exposure and separate peaks for exposed people. Select hearing protection for the actual task, fit and PPE compatibility and provide required hearing surveillance.

Apply the learning

A quiet break is used to justify an unassessed high-impact task with sharp noise peaks.

Decision and explanation

Assess representative daily exposure and the separate peak risk using suitable competent information.

Noise assessment needs suitable data for the decision and an understanding of uncertainty. Peak events and accumulated exposure are not interchangeable. Equipment emission information can help compare tools but may not describe the operator's position or surrounding sources. When the result affects control decisions and the evidence is weak, obtain competent advice rather than reporting a precise but unsupported number.

Lesson 4

Reduce noise at source

Prioritise a quieter suitable process, maintained equipment and engineering or layout controls, then address residual exposure.

Read the workface decision

Source reduction can protect several people at once and reduce the communication burden. Consider avoiding the noisy task, alternative methods, maintenance, enclosure, damping and separation where suitable. Check whether a quieter tool completes the actual job safely, rather than choosing by one catalogue figure. Residual protection and work organisation still need to match the assessed exposure.

Visual practice · Reduce noise at source

Actual SHAREsimulate construction model context: Noise masks warnings beside the plant route
Actual SHAREsimulate model capture · Noise masks warnings beside the plant route. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Read the workface decision

Source reduction can protect several people at once and reduce the communication burden. Consider avoiding the noisy task, alternative methods, maintenance, enclosure, damping and separation where suitable. Check whether a quieter tool completes the actual job safely, rather than choosing by one catalogue figure. Residual protection and work organisation still need to match the assessed exposure.

How can the ISO 45001 hierarchy of controls reduce workplace noise at source and protect hearing?

Remove an unnecessary noisy task, buy quieter equipment, enclose or damp the source, then limit residual exposure and fit hearing protection. Source basis: HSE · HSENI noise-induced hearing loss · five-level hierarchy of controls · HSE: Hearing protection · HSE source-control methods. Source basis: HSE · HSENI noise-induced hearing loss · five-level hierarchy of controls · HSE: Hearing protection · HSE source-control methods.

Evidence to establish at the workface

Eliminate unnecessary noisy stages or select quieter processes and suitable equipment; include noise performance in procurement and planning rather than accept it as an unavoidable site condition.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How can the ISO 45001 hierarchy of controls reduce workplace noise at source and protect hearing?

Remove an unnecessary noisy task, buy quieter equipment, enclose or damp the source, then limit residual exposure and fit hearing protection.

HSE prioritises eliminating and substituting hazards before engineering controls, administrative controls and PPE, as explained in its five-level hierarchy of controls. SHARE uses ERICPD as a task-planning prompt: Eliminate; Reduce, including substitution; Isolate through engineered separation; Control with other engineered or administrative measures; PPE; and Discipline, meaning continued verification and maintenance. ERICPD is not a sixth HSE level or a separate legal duty. The example below is a feasibility test for this work, not a universal prescription.

How can the ERICPD hierarchy of controls reduce workplace noise at source and protect hearing?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for Noise at Work
Activity and release context
A site plan should state who installs each source measure, where measurements will be repeated and what stops operation. Protectors support the plan; they do not turn an untreated noisy machine into acceptable source control. Sources: HSE noise construction controls , HSE noise hearing protection .
Full example
How can the hierarchy of controls reduce workplace noise at source and protect hearing?
Five-level hierarchyTask-specific measure, feasibility and ownerVerification and stop point
EliminateRemove an unnecessary compressed-air cleaning step and use a non-air cleaning method; process owner confirms product quality and other hazards.Observe the task and verify the compressor is not used; hold a reintroduced blow-off job. Sources: HSE; HSENI.
ReduceProcure a lower-noise saw or nozzle for the same output; buyer and engineer compare supplier data under the intended load.Acceptance measurement at the operator position; reject an unverified noisy replacement. Sources: HSE; HSENI.
EngineeringEnclose the saw, fit damping and place the compressor away from occupied work; engineer checks guarding, access and heat.Measure outside the enclosure and check door seals; failed enclosure or new rattling stops use. Sources: HSE; HSENI.
AdministrativeSupervisor limits time in the remaining noisy area and marks access; exposure assessor calculates actual full-shift exposure.Observe access and repeat exposure estimate after changed shifts; duration alone is not source control. Sources: HSE; HSENI.
PPEFit suitable hearing protection for residual noise and teach seal checks.Inspect fit and use; surveillance trend or defect restarts the source-control review. Sources: HSE; HSENI.
Discipline / continuing assuranceContinuing checks mean maintenance, supervision and learning after the stronger controls.

How can the ISO 45001 hierarchy of controls reduce workplace noise at source and protect hearing?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for Noise at Work
Activity and release context
A site plan should state who installs each source measure, where measurements will be repeated and what stops operation. Protectors support the plan; they do not turn an untreated noisy machine into acceptable source control. Sources: HSE noise construction controls , HSE noise hearing protection .
Full example
Read the activity, checks and hand-back in context
Five-level hierarchyTask-specific measure, feasibility and ownerVerification and stop point
EliminationRemove an unnecessary compressed-air cleaning step and use a non-air cleaning method; process owner confirms product quality and other hazards.Observe the task and verify the compressor is not used; hold a reintroduced blow-off job. Sources: HSE; HSENI.
SubstitutionProcure a lower-noise saw or nozzle for the same output; buyer and engineer compare supplier data under the intended load.Acceptance measurement at the operator position; reject an unverified noisy replacement. Sources: HSE; HSENI.
EngineeringEnclose the saw, fit damping and place the compressor away from occupied work; engineer checks guarding, access and heat.Measure outside the enclosure and check door seals; failed enclosure or new rattling stops use. Sources: HSE; HSENI.
AdministrativeSupervisor limits time in the remaining noisy area and marks access; exposure assessor calculates actual full-shift exposure.Observe access and repeat exposure estimate after changed shifts; duration alone is not source control. Sources: HSE; HSENI.
PPEFit suitable hearing protection for residual noise and teach seal checks.Inspect fit and use; surveillance trend or defect restarts the source-control review. Sources: HSE; HSENI.
Administrative controls / continuing assuranceContinuing checks mean maintenance, supervision and learning after the stronger controls.

A site plan should state who installs each source measure, where measurements will be repeated and what stops operation. Protectors support the plan; they do not turn an untreated noisy machine into acceptable source control. Sources: HSE noise construction controls, HSE noise hearing protection.

Match the control to the path. Damping reduces vibration of a resonant panel; a silencer reduces air-flow or exhaust noise; insulation and a sealed enclosure block sound transmission; absorptive lining reduces reflected sound in a room but may do little to the direct path beside a saw. The engineer tests the actual frequency and operating mode, then confirms the reduction at the worker position. HSE source-control methods

Continue with representative noise assessment and source-control planning and the hearing-concern and clinical pathway. Source control, exposure calculation and personal clinical assessment answer separate questions.

Read the practical categories separately: elimination removes the hazardous task/source; substitution replaces it with a suitable safer alternative; physical separation, containment and capture are engineering decisions. Duration/access/briefing are administrative measures, PPE covers residual exposure, and continued inspection, maintenance and verified action closure sustain the controls. Exposure monitoring or dosimetry measures exposure rather than protecting a person. The detailed text and records below distinguish these decisions; an overview illustration is not task authorisation.

Evidence to establish at the workface

Eliminate unnecessary noisy stages or select quieter processes and suitable equipment; include noise performance in procurement and planning rather than accept it as an unavoidable site condition.

Apply the learning

The proposed noise plan consists only of issuing earplugs beside poorly maintained cutting equipment.

Decision and explanation

Prioritise a quieter suitable process, maintained equipment and engineering or layout controls, then address residual exposure.

Source reduction can protect several people at once and reduce the communication burden. Consider avoiding the noisy task, alternative methods, maintenance, enclosure, damping and separation where suitable. Check whether a quieter tool completes the actual job safely, rather than choosing by one catalogue figure. Residual protection and work organisation still need to match the assessed exposure.

Lesson 5

Select hearing protection that works with the task

Resolve fit, compatibility, suitable attenuation and warning arrangements as part of the noise-control system.

Read the workface decision

Hearing protection depends on selection, fit, condition, consistent use and compatibility with other equipment. Excessive attenuation can also complicate communication; selection needs competent consideration of the task. It remains a residual control rather than a reason to leave avoidable noise unchanged. Verify that people can receive critical warnings under the conditions in which they actually work.

Visual practice · Select hearing protection that works with the task

Sound level measurement at a UK industrial workplace
SHAREhub photographic illustration · Sound level measurement at a UK industrial workplace. Use the written case for the exercise; this image does not prove a defect or safe system.
Read the workface decision

Hearing protection depends on selection, fit, condition, consistent use and compatibility with other equipment. Excessive attenuation can also complicate communication; selection needs competent consideration of the task. It remains a residual control rather than a reason to leave avoidable noise unchanged. Verify that people can receive critical warnings under the conditions in which they actually work.

How can the ISO 45001 hierarchy of controls turn noise assessments into stronger exposure controls?

Rank source removal, quieter substitution and engineering ahead of time limits and hearing protectors; name an owner and acceptance measure. Source basis: HSE noise hearing protection · HSE · five-level hierarchy of controls · HSENI · HSE advises avoiding protected levels below 70 dB at the ear. HSE prioritises eliminating and substituting hazards before engineering controls, administrative controls and PPE, as explained in its five-level hierarchy of controls.

Evidence to establish at the workface

Map the real workday and simultaneous sources with workers: include exposure from several jobs, waiting positions and transient peaks, not only one tool’s advertised emission. Check the noise-control action plan against the workface and observe the fit and use of protectors, including whether workers remove them to communicate or because other PPE interferes.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How can the ISO 45001 hierarchy of controls turn noise assessments into stronger exposure controls?

Rank source removal, quieter substitution and engineering ahead of time limits and hearing protectors; name an owner and acceptance measure.

HSE prioritises eliminating and substituting hazards before engineering controls, administrative controls and PPE, as explained in its five-level hierarchy of controls. SHARE uses ERICPD as a task-planning prompt: Eliminate; Reduce, including substitution; Isolate through engineered separation; Control with other engineered or administrative measures; PPE; and Discipline, meaning continued verification and maintenance. ERICPD is not a sixth HSE level or a separate legal duty. The example below is a feasibility test for this work, not a universal prescription.

How can the ERICPD hierarchy of controls turn noise assessments into stronger exposure controls?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Worked activity: Task application for Noise Risk Assessment and Hearing Conservation
Activity and release context
Select hearing protection for the measured spectrum and task. Fit, compatibility with other PPE, comfort, speech and warnings matter. An SNR shortcut is limited, especially for low-frequency noise; specialist frequency-band assessment may be needed. Record the residual risk and verify the source controls before relaxing zones or surveillance. Sources: HSE noise hearing protection , HSE over-protection guidance .
Full example
How can the hierarchy of controls turn noise assessments into stronger exposure controls?
Five-level hierarchyTask-specific measure, feasibility and ownerVerification and stop point
EliminateRemove an unnecessary noisy test where feasible; engineer verifies product quality without that noise-generating task. If the motor still runs and observation is remote, retain that option as engineered separation rather than physical removal of the noise hazard.Confirm the revised method in a live trial; stop if manual presence returns. Sources: HSE; HSENI.
SubstitutionSubstitute a genuinely lower-noise test rig where engineering and product requirements allow; compare sound and throughput. Reducing the existing rig’s speed is a separate operating/engineering optimisation, not by itself replacement of the hazard.Representative measurements and technical sign-off; reject a change creating another hazard. Sources: HSE; HSENI.
EngineeringEnclose the rig and seal service openings, with a safe viewing position; engineer checks cooling and access.Post-installation sound survey and maintenance checks; missing panel stops the test. Sources: HSE; HSENI.
AdministrativeSet test duration and restricted access based on measured daily exposure; assessor updates the calculation for overtime and peaks.Task log, measured duration and repeat assessment; changed duty cycle triggers reassessment. Sources: HSE; HSENI.
PPESelect and fit hearing protection against residual levels without over-protection.Observed use and surveillance trend; failed fit or threshold shift triggers review. Sources: HSE; HSENI.
Discipline / continuing assuranceContinuing checks mean ongoing fit checks, hearing data review and corrective action.

How can the ISO 45001 hierarchy of controls turn noise assessments into stronger exposure controls?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Worked activity: Task application for Noise Risk Assessment and Hearing Conservation
Activity and release context
Select hearing protection for the measured spectrum and task. Fit, compatibility with other PPE, comfort, speech and warnings matter. An SNR shortcut is limited, especially for low-frequency noise; specialist frequency-band assessment may be needed. Record the residual risk and verify the source controls before relaxing zones or surveillance. Sources: HSE noise hearing protection , HSE over-protection guidance .
Full example
Read the activity, checks and hand-back in context
Five-level hierarchyTask-specific measure, feasibility and ownerVerification and stop point
EliminateRemove an unnecessary noisy test where feasible; engineer verifies product quality without that noise-generating task. If the motor still runs and observation is remote, retain that option as engineered separation rather than physical removal of the noise hazard.Confirm the revised method in a live trial; stop if manual presence returns. Sources: HSE; HSENI.
SubstitutionSubstitute a genuinely lower-noise test rig where engineering and product requirements allow; compare sound and throughput. Reducing the existing rig’s speed is a separate operating/engineering optimisation, not by itself replacement of the hazard.Representative measurements and technical sign-off; reject a change creating another hazard. Sources: HSE; HSENI.
EngineeringEnclose the rig and seal service openings, with a safe viewing position; engineer checks cooling and access.Post-installation sound survey and maintenance checks; missing panel stops the test. Sources: HSE; HSENI.
AdministrativeSet test duration and restricted access based on measured daily exposure; assessor updates the calculation for overtime and peaks.Task log, measured duration and repeat assessment; changed duty cycle triggers reassessment. Sources: HSE; HSENI.
PPESelect and fit hearing protection against residual levels without over-protection.Observed use and surveillance trend; failed fit or threshold shift triggers review. Sources: HSE; HSENI.
Administrative controls / continuing assuranceContinuing checks mean ongoing fit checks, hearing data review and corrective action.

Select hearing protection for the measured spectrum and task. Fit, compatibility with other PPE, comfort, speech and warnings matter. An SNR shortcut is limited, especially for low-frequency noise; specialist frequency-band assessment may be needed. Record the residual risk and verify the source controls before relaxing zones or surveillance. Sources: HSE noise hearing protection, HSE over-protection guidance.

Read the practical categories separately: elimination removes the hazardous task/source; substitution replaces it with a suitable safer alternative; physical separation, containment and capture are engineering decisions. Duration/access/briefing are administrative measures, PPE covers residual exposure, and continued inspection, maintenance and verified action closure sustain the controls. Exposure monitoring or dosimetry measures exposure rather than protecting a person. The detailed text and records below distinguish these decisions; an overview illustration is not task authorisation.

Evidence to establish at the workface

Map the real workday and simultaneous sources with workers: include exposure from several jobs, waiting positions and transient peaks, not only one tool’s advertised emission. Check the noise-control action plan against the workface and observe the fit and use of protectors, including whether workers remove them to communicate or because other PPE interferes.

Apply the learning

A worker's earmuffs are displaced by other head protection and the alarm cannot be understood.

Decision and explanation

Resolve fit, compatibility, suitable attenuation and warning arrangements as part of the noise-control system.

Hearing protection depends on selection, fit, condition, consistent use and compatibility with other equipment. Excessive attenuation can also complicate communication; selection needs competent consideration of the task. It remains a residual control rather than a reason to leave avoidable noise unchanged. Verify that people can receive critical warnings under the conditions in which they actually work.

Lesson 6

Check communication and hearing conservation

Stop the conflicted operation and establish reliable separation, coordination and communication before resuming.

Read the workface decision

Immediate safety communication must remain reliable within the exposure-control plan. Changing one person's PPE can create a second hazard without resolving the first. Coordinate noisy work and vehicle movements, use an agreed suitable communication method and verify it in practice. Hearing health surveillance, where required, provides a separate early-warning system and must lead to appropriate action rather than replace exposure reduction.

Visual practice · Check communication and hearing conservation

Actual SHAREsimulate construction model context: Noise masks warnings beside the plant route
Actual SHAREsimulate model capture · Noise masks warnings beside the plant route. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Read the workface decision

Immediate safety communication must remain reliable within the exposure-control plan. Changing one person's PPE can create a second hazard without resolving the first. Coordinate noisy work and vehicle movements, use an agreed suitable communication method and verify it in practice. Hearing health surveillance, where required, provides a separate early-warning system and must lead to appropriate action rather than replace exposure reduction.

When is hearing surveillance indicated and how is it used?

Provide regular hearing checks for workers regularly above the upper action value or otherwise at particular risk, under an occupational-health programme. A baseline before exposure is useful where feasible. HSE describes a typical schedule, not an automatic fixed legal interval; a competent provider adapts checks to risk and findings.

Evidence to establish at the workface

Assess representative daily or appropriate weekly exposure and separate peaks for exposed people. Select hearing protection for the actual task, fit and PPE compatibility and provide required hearing surveillance.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

When is hearing surveillance indicated and how is it used?

Provide regular hearing checks for workers regularly above the upper action value or otherwise at particular risk, under an occupational-health programme.

A baseline before exposure is useful where feasible. HSE describes a typical schedule, not an automatic fixed legal interval; a competent provider adapts checks to risk and findings. Workers receive results; employers retain health and fitness advice, while clinical records stay confidential. A change in audiometry prompts exposure and source-control review. HSE and HSENI describe the separate routes.

The occupational-health provider owns the surveillance schedule: obtain an early baseline, annual checks initially, then a risk-adjusted interval. HSE’s usual guidance is annual checks for the first two years and then three-yearly checks, with earlier review for abnormal findings or high risk. This is guidance, not an automatic statutory interval or a reason to delay symptom assessment.

Evidence to establish at the workface

Assess representative daily or appropriate weekly exposure and separate peaks for exposed people. Select hearing protection for the actual task, fit and PPE compatibility and provide required hearing surveillance.

Apply the learning

A signaller and driver cannot understand one another during nearby cutting, although both wear hearing protection.

Decision and explanation

Stop the conflicted operation and establish reliable separation, coordination and communication before resuming.

Immediate safety communication must remain reliable within the exposure-control plan. Changing one person's PPE can create a second hazard without resolving the first. Coordinate noisy work and vehicle movements, use an agreed suitable communication method and verify it in practice. Hearing health surveillance, where required, provides a separate early-warning system and must lead to appropriate action rather than replace exposure reduction.

Lesson 7

Recognise hand-arm vibration harm

Report symptoms promptly through the health arrangements and improve the exposure controls without waiting for deterioration.

Read the workface decision

Hand-arm vibration can affect circulation, nerves and function, sometimes with lasting consequences. Symptoms deserve a prompt occupational-health response, but a supervisor should not make a medical diagnosis. The workface response also considers the tool, condition, material and working time. A health report is useful evidence that controls need attention, rather than a reason to blame the person reporting it.

An open palm beside a separate enlarged finger cutaway showing skin, joints, bones, red and blue vessels and yellow nerves.View full detail ↗
Whole hand and enlarged finger

Locate the index finger in the whole hand. The separate cutaway enlarges skin, bones, vessels and nerves; colours distinguish the structures.

Keep circulation, sensation and movement distinct. Which tool or work-method change would reduce the exposure described here?

educational illustration · healthy anatomy; enlarged details and teaching colours.

Visual practice · Recognise hand-arm vibration harm

Inspection of a hand-held breaker and vibration sensor
SHAREhub photographic illustration · Inspection of a hand-held breaker and vibration sensor. Use the written case for the exercise; this image does not prove a defect or safe system.
Read the workface decision

Hand-arm vibration can affect circulation, nerves and function, sometimes with lasting consequences. Symptoms deserve a prompt occupational-health response, but a supervisor should not make a medical diagnosis. The workface response also considers the tool, condition, material and working time. A health report is useful evidence that controls need attention, rather than a reason to blame the person reporting it.

Which symptoms need an early response?

Tingling, numbness, finger blanching, loss of grip or dexterity after tool work, and back discomfort associated with jolting vehicle work, should be reported and assessed promptly. HAV can cause hand-arm vibration syndrome and carpal tunnel syndrome; continuing exposure can make harm permanent. WBV is associated with back pain, but posture, lifting and other work factors may contribute.

See the actual construction-model example

The worker uses a poorly maintained breaker for long periods and reports tingling fingers. Hand-arm vibration can damage nerves and circulation and affect grip and fine control. Symptoms are a reason to act promptly, not an expected sign of hard work to ignore. The tool also creates noise and dust and may impose awkward force or posture; controlling one exposure does not establish that the whole breaking task is safe.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Which symptoms need an early response?

Tingling, numbness, finger blanching, loss of grip or dexterity after tool work, and back discomfort associated with jolting vehicle work, should be reported and assessed promptly.

HAV can cause hand-arm vibration syndrome and carpal tunnel syndrome; continuing exposure can make harm permanent. WBV is associated with back pain, but posture, lifting and other work factors may contribute. Workers should not wait for a daily calculation or routine annual check before raising symptoms. A supervisor should review exposure and controls and seek occupational-health advice without making a diagnosis or disclosing confidential clinical details. See HSE.

SignalWork response
New HAV symptomsReport, review exposure and refer through OH route. Source
White fingers or lost dexterityDo not treat this as ordinary cold or fatigue; assess promptly. Source
Back pain after repeated joltsReview route, machine, seat, speed and other back-pain factors. Source: HSE whole-body vibration

Basis: HSE HAV health surveillance guidance for occupational health professionals; HSE Whole-body vibration at work; HSE Whole-body vibration in docks; HSE Health surveillance overview

See the actual construction-model example

The worker uses a poorly maintained breaker for long periods and reports tingling fingers. Hand-arm vibration can damage nerves and circulation and affect grip and fine control. Symptoms are a reason to act promptly, not an expected sign of hard work to ignore. The tool also creates noise and dust and may impose awkward force or posture; controlling one exposure does not establish that the whole breaking task is safe.

Avoid or reduce the breaking task first, for example through design, precast openings or a suitable lower-exposure mechanical method. Where hand-held tools remain necessary, choose effective lower-vibration equipment for the actual material and maintain the tool, consumable and anti-vibration features. A tool that performs poorly may increase both vibration and the time needed. Anti-vibration gloves are not a reliable substitute for controlling vibration at source.

Assess actual exposure from every relevant tool used in the day. Trigger time means time in effective contact with operating vibrating equipment, not the whole booked shift, while several tools contribute to the same person’s exposure. Manufacturer emission figures need task-relevant interpretation; do not allocate an arbitrary universal safe number of minutes. Review work patterns after stronger controls, provide information and indicated health surveillance, and obtain occupational-health advice on symptoms and restrictions. Protect medical confidentiality while making the necessary task changes.

Evidence to establish at the workface

Remove the defective tool from use, act on the reported symptoms and obtain appropriate occupational-health advice while reviewing exposure and work restrictions.

Apply the learning

A breaker user reports tingling and loss of finger sensation and is told it is a normal part of the trade.

Decision and explanation

Report symptoms promptly through the health arrangements and improve the exposure controls without waiting for deterioration.

Hand-arm vibration can affect circulation, nerves and function, sometimes with lasting consequences. Symptoms deserve a prompt occupational-health response, but a supervisor should not make a medical diagnosis. The workface response also considers the tool, condition, material and working time. A health report is useful evidence that controls need attention, rather than a reason to blame the person reporting it.

Lesson 8

Build a defensible HAV exposure estimate

Establish representative trigger time and suitable vibration information with uncertainty and task variation recorded.

Read the workface decision

Exposure calculations depend on credible input data. Distinguish the time a tool is available from time it is operating in contact with the work, while including all relevant tools used during the day. Catalogue values may not represent the actual material, accessory or condition. Monitoring can improve an estimate, but an electronic timer does not itself reduce vibration or establish that the selected controls are sufficient.

Visual practice · Build a defensible HAV exposure estimate

Actual SHAREsimulate construction model context: A damaged breaker is used for excessive trigger time
Actual SHAREsimulate model capture · A damaged breaker is used for excessive trigger time. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Read the workface decision

Exposure calculations depend on credible input data. Distinguish the time a tool is available from time it is operating in contact with the work, while including all relevant tools used during the day. Catalogue values may not represent the actual material, accessory or condition. Monitoring can improve an estimate, but an electronic timer does not itself reduce vibration or establish that the selected controls are sufficient.

How should exposure duration be established?

Observe enough representative work to estimate the time the worker is actually exposed to vibration; do not substitute shift length, booking time or machine availability. For HAV, trigger or contact time is when the hands are actually exposed to vibration from the operating tool or process. Repeated short operations can be sampled and multiplied by a typical workload.

Evidence to establish at the workface

Avoid unnecessary breaking and select a suitable lower-exposure method before relying on time limits, rotation or protective clothing.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should exposure duration be established?

Observe enough representative work to estimate the time the worker is actually exposed to vibration; do not substitute shift length, booking time or machine availability.

For HAV, trigger or contact time is when the hands are actually exposed to vibration from the operating tool or process. Repeated short operations can be sampled and multiplied by a typical workload. Include every HAV source in that person’s day, across departments or contractors where relevant. For WBV, establish representative driving/operating periods and severe shock events, not simply engine hours. Consider peaks and longer days, not only an average that hides high exposure.

Weak durationBetter evidence
Eight-hour shiftObserved trigger/exposure time by task.
Tool signed out all daySample cycles or time log checked against work output.
Vehicle engine hoursActual operating/driving pattern and route conditions.
Planned timeActual use plus credible variability and changed work.

Basis: HSE Vibration risk assessment; HSE L140 Hand-arm vibration; HSE L141 Whole-body vibration

Evidence to establish at the workface

Avoid unnecessary breaking and select a suitable lower-exposure method before relying on time limits, rotation or protective clothing.

Apply the learning

A breaker is available for eight hours but actually contacts the work intermittently, and the recorded time is guessed.

Decision and explanation

Establish representative trigger time and suitable vibration information with uncertainty and task variation recorded.

Exposure calculations depend on credible input data. Distinguish the time a tool is available from time it is operating in contact with the work, while including all relevant tools used during the day. Catalogue values may not represent the actual material, accessory or condition. Monitoring can improve an estimate, but an electronic timer does not itself reduce vibration or establish that the selected controls are sufficient.

Lesson 9

Avoid or reduce vibrating tasks

Consider design or process alternatives and suitable maintained equipment before relying on duration limits.

Read the workface decision

The strongest control may be to avoid the intrusive task through design, prefabrication or another suitable process. Where vibration remains, equipment and working technique affect both magnitude and duration. Rotation needs to reduce individual exposure in a planned way; moving people between similarly high exposures can simply distribute risk. Check the complete alternative for dust, noise, access and other hazards.

Visual practice · Avoid or reduce vibrating tasks

Inspection of a hand-held breaker and vibration sensor
SHAREhub photographic illustration · Inspection of a hand-held breaker and vibration sensor. Use the written case for the exercise; this image does not prove a defect or safe system.
Read the workface decision

The strongest control may be to avoid the intrusive task through design, prefabrication or another suitable process. Where vibration remains, equipment and working technique affect both magnitude and duration. Rotation needs to reduce individual exposure in a planned way; moving people between similarly high exposures can simply distribute risk. Check the complete alternative for dust, noise, access and other hazards.

How should stronger source controls be chosen?

Start by avoiding the hazardous task or release, then use suitable substitution and physical controls before relying on work rules or personal protection. The order guides a decision; the actual control depends on this task, the people exposed and what a change could introduce. A supervisor should observe the control during real work, hold a failed task and obtain a competent release after correction.

Evidence to establish at the workface

Check the real breaking method, tool condition, consumable and material and compare achievable lower-exposure alternatives rather than purchasing from one emission number. Review representative trigger-time evidence for each worker’s complete tool day, including changes, overtime and uncertainty in the exposure estimate.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should stronger source controls be chosen?

Start by avoiding the hazardous task or release, then use suitable substitution and physical controls before relying on work rules or personal protection.

The order guides a decision; the actual control depends on this task, the people exposed and what a change could introduce. A supervisor should observe the control during real work, hold a failed task and obtain a competent release after correction. HSE guidance for this control decision

Control layerTask decision
AvoidAvoid unnecessary vibrating work
Substitute or reduceChoose an efficient lower-vibration method for the task
EngineerUse supported tools, sound consumables and maintained vehicle routes
Organise and verifyAssess each person’s combined day and stop for symptoms or changed exposure
Protect residual exposureGloves do not establish vibration compliance

Evidence to establish at the workface

Check the real breaking method, tool condition, consumable and material and compare achievable lower-exposure alternatives rather than purchasing from one emission number. Review representative trigger-time evidence for each worker’s complete tool day, including changes, overtime and uncertainty in the exposure estimate.

Apply the learning

A team proposes longer rotation between two identical breakers while leaving an avoidable breaking task unchanged.

Decision and explanation

Consider design or process alternatives and suitable maintained equipment before relying on duration limits.

The strongest control may be to avoid the intrusive task through design, prefabrication or another suitable process. Where vibration remains, equipment and working technique affect both magnitude and duration. Rotation needs to reduce individual exposure in a planned way; moving people between similarly high exposures can simply distribute risk. Check the complete alternative for dust, noise, access and other hazards.

Lesson 10

Maintenance, grip and cold conditions

Correct equipment defects and the working method; use warmth and hand protection appropriately without treating gloves as reliable vibration control.

Read the workface decision

Tool wear may increase vibration and make the work slower. Suitable accessories, maintenance, support and working posture can improve the real task. Keeping hands and the body warm and dry supports wellbeing, but gloves should not be used as proof that vibration exposure has been controlled. A defect system must be able to remove the tool before the production plan depends on it.

Visual practice · Maintenance, grip and cold conditions

Actual SHAREsimulate construction model context: A damaged breaker is used for excessive trigger time
Actual SHAREsimulate model capture · A damaged breaker is used for excessive trigger time. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Read the workface decision

Tool wear may increase vibration and make the work slower. Suitable accessories, maintenance, support and working posture can improve the real task. Keeping hands and the body warm and dry supports wellbeing, but gloves should not be used as proof that vibration exposure has been controlled. A defect system must be able to remove the tool before the production plan depends on it.

Do anti-vibration gloves solve HAV risk?

Usually not. Do not credit anti-vibration gloves as the primary exposure reduction; suitable gloves and clothing can keep hands warm and dry, which supports circulation. HSE says glove attenuation is difficult to predict in real tool use and can be ineffective or even increase vibration at some frequencies.

Evidence to establish at the workface

Remove the defective tool from use, act on the reported symptoms and obtain appropriate occupational-health advice while reviewing exposure and work restrictions.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Do anti-vibration gloves solve HAV risk?

Usually not. Do not credit anti-vibration gloves as the primary exposure reduction; suitable gloves and clothing can keep hands warm and dry, which supports circulation.

HSE says glove attenuation is difficult to predict in real tool use and can be ineffective or even increase vibration at some frequencies. Thick gloves may reduce dexterity or increase grip force. Select gloves for warmth and other task hazards without creating entanglement or loss of control, but calculate and reduce exposure through method, equipment and work planning.

Basis: HSE Gloves and warm clothing; HSE L140 Hand-arm vibration; HSE Construction vibration FAQ

Evidence to establish at the workface

Remove the defective tool from use, act on the reported symptoms and obtain appropriate occupational-health advice while reviewing exposure and work restrictions.

Apply the learning

A blunt breaker bit and loose handle are tolerated because workers have gloves labelled anti-vibration.

Decision and explanation

Correct equipment defects and the working method; use warmth and hand protection appropriately without treating gloves as reliable vibration control.

Tool wear may increase vibration and make the work slower. Suitable accessories, maintenance, support and working posture can improve the real task. Keeping hands and the body warm and dry supports wellbeing, but gloves should not be used as proof that vibration exposure has been controlled. A defect system must be able to remove the tool before the production plan depends on it.

Lesson 11

Health surveillance and confidential action

Use occupational-health advice on fitness and necessary work restrictions while protecting confidential clinical information.

Read the workface decision

Health surveillance is a structured route for identifying early harm and taking action, distinct from measuring the tool. Managers need relevant fitness and control advice, not unrestricted access to a person's clinical details. Findings may require individual action and improvements to the wider system. Explain reporting and confidentiality so workers can raise concerns without the process becoming punitive.

Visual practice · Health surveillance and confidential action

Inspection of a hand-held breaker and vibration sensor
SHAREhub photographic illustration · Inspection of a hand-held breaker and vibration sensor. Use the written case for the exercise; this image does not prove a defect or safe system.
Read the workface decision

Health surveillance is a structured route for identifying early harm and taking action, distinct from measuring the tool. Managers need relevant fitness and control advice, not unrestricted access to a person's clinical details. Findings may require individual action and improvements to the wider system. Explain reporting and confidentiality so workers can raise concerns without the process becoming punitive.

Which health records should the employer keep?

Keep the employee’s identity, exposure history and occupational-health fitness outcome or restrictions in the health record; confidential questionnaires, clinical findings and diagnosis remain in the medical record held by occupational health. L140 advises keeping the health record for as long as the person remains under surveillance and offering a copy when exposure or employment ends; additional retention must be justified rather than invented here. The employer should receive enough information to control work without collecting unnecessary clinical detail.

Evidence to establish at the workface

Avoid unnecessary breaking and select a suitable lower-exposure method before relying on time limits, rotation or protective clothing.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Which health records should the employer keep?

Keep the employee’s identity, exposure history and occupational-health fitness outcome or restrictions in the health record; confidential questionnaires, clinical findings and diagnosis remain in the medical record held by occupational health.

L140 advises keeping the health record for as long as the person remains under surveillance and offering a copy when exposure or employment ends; additional retention must be justified rather than invented here. The employer should receive enough information to control work without collecting unnecessary clinical detail. Store access-controlled records and use anonymised group feedback for assurance. Workers can access their personal health record under the vibration regulations.

RecordHolder/use
Health recordEmployer: identity, exposure history and fitness/restrictions.
Medical recordOccupational health: confidential clinical information.
Task exposure recordOperations: tools, duration, assumptions and controls; no diagnosis.
Group trendManagement: anonymised control feedback.

Basis: Control of Vibration at Work Regulations 2005; Control of Vibration at Work Regulations (Northern Ireland) 2005; HSE L140 Hand-arm vibration; HSE Health surveillance overview

Evidence to establish at the workface

Avoid unnecessary breaking and select a suitable lower-exposure method before relying on time limits, rotation or protective clothing.

Apply the learning

A supervisor requests the worker's full medical notes to decide whether the breaker can still be used.

Decision and explanation

Use occupational-health advice on fitness and necessary work restrictions while protecting confidential clinical information.

Health surveillance is a structured route for identifying early harm and taking action, distinct from measuring the tool. Managers need relevant fitness and control advice, not unrestricted access to a person's clinical details. Findings may require individual action and improvements to the wider system. Explain reporting and confidentiality so workers can raise concerns without the process becoming punitive.

Lesson 12

Distinguish whole-body vibration

Assess the vehicle, route, shocks, posture and operating pattern as a whole-body vibration problem.

Read the workface decision

Whole-body vibration enters through the seat or feet and differs from hand-transmitted exposure. Repeated shocks, awkward posture and other physical demands can contribute to back problems. The route and vehicle form a connected system. A complaint should prompt investigation of those conditions and appropriate health advice, while the model view itself cannot diagnose a person's back condition.

A worker in navy clothing seen from behind beside a separate enlarged side view of the lumbar spine and sacrum, with discs, yellow nerve roots and back muscle.View full detail ↗
The lower back: location and side view

The worker locates the lower back; the separate side view enlarges its bones, discs, nerve roots and nearby muscle.

Locate the lower back. How could the load, reach, route, equipment or work pattern be changed for the task in this lesson?

educational illustration · healthy anatomy; enlarged details and teaching colours.

Visual practice · Distinguish whole-body vibration

Actual SHAREsimulate construction model context: A rough haul road jolts plant operators
Actual SHAREsimulate model capture · A rough haul road jolts plant operators. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Read the workface decision

Whole-body vibration enters through the seat or feet and differs from hand-transmitted exposure. Repeated shocks, awkward posture and other physical demands can contribute to back problems. The route and vehicle form a connected system. A complaint should prompt investigation of those conditions and appropriate health advice, while the model view itself cannot diagnose a person's back condition.

How is WBV assessed without borrowing HAV rules?

Assess vehicle and task exposure through the seat or feet, including roughness, speed, shocks and time, against the WBV daily values; HAV tool points are not a WBV calculator. Look at road or ground condition, vehicle type and suspension, seat adjustment, tyres, load, driving pattern and repeated jolts. Consider awkward posture, climbing, lifting and other contributors to back pain.

See the actual construction-model example

The dumper’s potholes and ridges transmit vibration and shocks through the seat to the operator. This is whole-body vibration, which differs from vibration transmitted into the hands by breakers and drills. Repeated jolting, awkward posture, poor seat adjustment and later manual handling can combine as contributors to back pain. The road also affects control and vehicle stability, so a health complaint may reveal a wider route defect. An operator’s discomfort is useful information to investigate, not a diagnosis made by looking at the model.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How is WBV assessed without borrowing HAV rules?

Assess vehicle and task exposure through the seat or feet, including roughness, speed, shocks and time, against the WBV daily values; HAV tool points are not a WBV calculator.

Look at road or ground condition, vehicle type and suspension, seat adjustment, tyres, load, driving pattern and repeated jolts. Consider awkward posture, climbing, lifting and other contributors to back pain. HSE notes many WBV problems can be reduced through simple site and machine changes without routine measurement. Competent assessment or measurement may be needed when the exposure category or effectiveness of controls remains uncertain. See HSE.

QuestionEvidence
Are large jolts present?Observe route and operator experience; address shocks promptly. Source
Is the seat effective?Correct adjustment, suspension condition and driver training. Source
Is the route avoidable?Layout, maintenance, speed and transport need. Source
Can exposure be estimated?Representative task/vehicle data; competent measurement if needed. Source

Basis: HSE Whole-body vibration at work; HSE L141 Whole-body vibration; HSE AIS20 Whole-body vibration in agriculture; HSE Whole-body vibration in docks

See the actual construction-model example

The dumper’s potholes and ridges transmit vibration and shocks through the seat to the operator. This is whole-body vibration, which differs from vibration transmitted into the hands by breakers and drills. Repeated jolting, awkward posture, poor seat adjustment and later manual handling can combine as contributors to back pain. The road also affects control and vehicle stability, so a health complaint may reveal a wider route defect. An operator’s discomfort is useful information to investigate, not a diagnosis made by looking at the model.

Begin with the journey and work design: reduce unnecessary trips, provide a suitable maintained route and select plant, tyres, suspension and seating matched to the task. Speed should fit the actual surface and safe operation, not a delivery target. Assess representative whole-day use across machines, routes and changes, using competent information or measurement where necessary. A manufacturer’s emission value is not a promise of exposure on a rain-damaged haul road. There is no glove or other ordinary PPE that substitutes for whole-body vibration control. Encourage early symptom reporting and appropriate clinical advice, while using group learning to improve the route and equipment without publishing personal health details.

Evidence to establish at the workface

Select and maintain suitable plant, tyres, suspension and seating; train operators to adjust the seat and controls correctly and avoid sustained awkward postures.

Apply the learning

A dumper driver reports repeated jolts from potholes while the risk assessment contains only a hand-tool vibration calculation.

Decision and explanation

Assess the vehicle, route, shocks, posture and operating pattern as a whole-body vibration problem.

Whole-body vibration enters through the seat or feet and differs from hand-transmitted exposure. Repeated shocks, awkward posture and other physical demands can contribute to back problems. The route and vehicle form a connected system. A complaint should prompt investigation of those conditions and appropriate health advice, while the model view itself cannot diagnose a person's back condition.

Lesson 13

Improve routes, vehicles and seats

Improve the route, suitable vehicle, operating speed, seat setup and maintenance within a coordinated exposure plan.

Read the workface decision

Route maintenance can reduce shocks while also improving stability and vehicle control. Select equipment for the ground and task, maintain suspension and tyres as appropriate, and give drivers useful instruction on seat adjustment and technique. Exposure duration may still require attention after source measures. Check the improvement during representative loaded and unloaded journeys, without creating unsafe demonstrations.

Visual practice · Improve routes, vehicles and seats

Inspection of a hand-held breaker and vibration sensor
SHAREhub photographic illustration · Inspection of a hand-held breaker and vibration sensor. Use the written case for the exercise; this image does not prove a defect or safe system.
Read the workface decision

Route maintenance can reduce shocks while also improving stability and vehicle control. Select equipment for the ground and task, maintain suspension and tyres as appropriate, and give drivers useful instruction on seat adjustment and technique. Exposure duration may still require attention after source measures. Check the improvement during representative loaded and unloaded journeys, without creating unsafe demonstrations.

Which controls cut WBV and shocks?

Reduce the need to drive and the jolts at source: improve routes and ground, select suitable vehicles, maintain suspension, tyres and seats, and train drivers to use appropriate speed and posture. Fill potholes, grade routes, avoid steps and repeated crossings, and place material to reduce travel. Match plant to surface and load; maintain seat suspension and adjust it for the operator.

Evidence to establish at the workface

Inspect the route after rain or change and observe a representative trip from a safe location; do not rely on a smooth demonstration on the cabin access road. Ask operators about jolts, seat adjustment, visibility, travel patterns and the next task, including heavy manual handling after prolonged driving.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

Which controls cut WBV and shocks?

Reduce the need to drive and the jolts at source: improve routes and ground, select suitable vehicles, maintain suspension, tyres and seats, and train drivers to use appropriate speed and posture.

Fill potholes, grade routes, avoid steps and repeated crossings, and place material to reduce travel. Match plant to surface and load; maintain seat suspension and adjust it for the operator. Reduce speeds where jolts occur, without creating other traffic hazards. Time sharing and breaks may support control after the source has been improved, but there is no WBV personal protective equipment that substitutes for these measures. See HSE.

ControlCheck
Site/routePotholes, transitions, distance and detours. Source
MachineSuspension, tyres, load and maintenance. Source
Seat/operatorAdjustment, posture and driving practice. Source
Work planDuration and other back-pain tasks reviewed. Source

Basis: HSE Whole-body vibration at work; HSE L141 Whole-body vibration; HSE AIS20 Whole-body vibration in agriculture

Evidence to establish at the workface

Inspect the route after rain or change and observe a representative trip from a safe location; do not rely on a smooth demonstration on the cabin access road. Ask operators about jolts, seat adjustment, visibility, travel patterns and the next task, including heavy manual handling after prolonged driving.

Apply the learning

A repaired seat is proposed as the only response to repeated high-speed trips across a damaged haul road.

Decision and explanation

Improve the route, suitable vehicle, operating speed, seat setup and maintenance within a coordinated exposure plan.

Route maintenance can reduce shocks while also improving stability and vehicle control. Select equipment for the ground and task, maintain suspension and tyres as appropriate, and give drivers useful instruction on seat adjustment and technique. Exposure duration may still require attention after source measures. Check the improvement during representative loaded and unloaded journeys, without creating unsafe demonstrations.

Lesson 14

Coordinate industrial radiography

Hold conflicting work and coordinate the specialist's radiation arrangements and the site's affected areas before access is released.

Read the workface decision

Industrial radiography needs specialist control. Radiation can affect areas beyond the apparent work position, including other levels, and the boundary must follow the competent assessment and actual operation. Site management must coordinate other trades, access and emergency arrangements with the radiation employer. Ordinary workers should respect exclusion and report uncertainty, rather than measure, move or recover a source themselves.

Visual practice · Coordinate industrial radiography

Actual SHAREsimulate construction model context: Specialist radiation work is not coordinated
Actual SHAREsimulate model capture · Specialist radiation work is not coordinated. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Read the workface decision

Industrial radiography needs specialist control. Radiation can affect areas beyond the apparent work position, including other levels, and the boundary must follow the competent assessment and actual operation. Site management must coordinate other trades, access and emergency arrangements with the radiation employer. Ordinary workers should respect exclusion and report uncertainty, rather than measure, move or recover a source themselves.

How is ordinary radon management different from specialist radiation work?

Radon assessment begins with premises and occupancy. Deliberate use of radiation sources begins with a planned radiation practice, source-specific controls and the applicable notification, registration or consent. A generic premises checklist cannot authorise that work.

See the actual construction-model example

The specialist testing case and exclusion notices indicate a coordination decision before nearby trades continue. Industrial radiography may use ionising radiation to inspect welds or materials, with exposure possible beyond the immediate work position or on another level. A warning symbol identifies a hazard; it does not measure radiation or prove that the boundary is adequate. The radiography employer and site management must exchange relevant information and maintain effective control of the area during the work and any abnormal condition.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How is ordinary radon management different from specialist radiation work?

Radon assessment begins with premises and occupancy. Deliberate use of radiation sources begins with a planned radiation practice, source-specific controls and the applicable notification, registration or consent. A generic premises checklist cannot authorise that work.

For X-ray equipment and radioactive material, the radiation employer must assess normal work, maintenance and foreseeable accidents before starting. Suitable RPA advice informs shielding, access, monitoring, local rules and contingency arrangements. The Radiation Protection Supervisor (RPS) supervises compliance with local rules; the RPS and RPA are different roles. Specialist advice does not transfer the employer’s accountability.

Servicing an enclosed X-ray inspection cabinet

Task, material and setting: A service contractor repairs an X-ray inspection cabinet in a production area. The outcome is reliable inspection with enclosure and safety functions demonstrated before hand-back.

People and prerequisites: Operators, the service engineer and nearby employees could be exposed. The host and contractor identify the exact generator, authorised work scope, applicable permissioning, manufacturer information, competent service personnel and suitable RPA advice. This is a coordination example, not a servicing method.

Before: Take the cabinet out of normal use and apply the authorised isolation and access arrangements. Establish who controls the area and whether servicing could expose a beam or defeat normal shielding. Any such work needs its own specialist assessment and controls before it begins.

During: Only the authorised engineer performs the assessed work. Maintain exclusion and communication with the host; do not let production pressure create an unassessed live test or bypass. Use the measurements and checks specified by the specialist method.

Hold or stop: Stop for unexpected emission, failed isolation or interlock, uncertain source identity, missing instructions or anyone entering the controlled work area. If exposure is suspected or a source is missing, keep people clear, activate the site contingency plan and contact the responsible radiation personnel. Call emergency services for immediate danger. Do not improvise recovery, re-enter or fault-find around an exposed source.

Completion and hand back: Reinstate and verify shielding, interlocks and warning devices under the approved procedure, complete any required radiation survey and record release by the authorised responsible person. Brief operators about any change before restarting.

Evidence: Retain the task assessment, contractor coordination, source/equipment identity, service and test results, survey where required, defect closure and return-to-service approval.

For a sealed radioactive source, switching off electrical power does not switch off the radioactivity. Unknown or damaged source-containing equipment must be kept secure and referred to the responsible specialist. For a laser or UV system, wavelength, beam path, reflections and service mode require optical-radiation assessment rather than radon rules.

See the actual construction-model example

The specialist testing case and exclusion notices indicate a coordination decision before nearby trades continue. Industrial radiography may use ionising radiation to inspect welds or materials, with exposure possible beyond the immediate work position or on another level. A warning symbol identifies a hazard; it does not measure radiation or prove that the boundary is adequate. The radiography employer and site management must exchange relevant information and maintain effective control of the area during the work and any abnormal condition.

Radon is a separate ionising-radiation exposure from a naturally occurring gas that can accumulate in buildings or underground workplaces. Its assessment depends on location, occupancy, ventilation and appropriate measurements, not on whether the chamber’s ordinary oxygen or flammable-gas monitor reads normally. Specialist radiography needs suitable radiation protection advice, assessed boundaries, access control, monitoring and the relevant authorisation arrangements. Radon needs a workplace assessment and measurement or remediation route where indicated, with competent review and remeasurement after changes. Neither should be confused with welding UV or sunlight, which require different optical-radiation controls and instruments.

Evidence to establish at the workface

Ask the specialist and site coordinator to show how the boundaries address adjacent floors, public routes and simultaneous work; confirm the responsible access-control and communication roles. Verify suitable instrument, personnel and authorisation evidence and the agreed handback and emergency arrangements, without asking a learner to operate or approach the source.

Apply the learning

A radiography contractor sets an exclusion area but another trade plans to work on the floor above the source position.

Decision and explanation

Hold conflicting work and coordinate the specialist's radiation arrangements and the site's affected areas before access is released.

Industrial radiography needs specialist control. Radiation can affect areas beyond the apparent work position, including other levels, and the boundary must follow the competent assessment and actual operation. Site management must coordinate other trades, access and emergency arrangements with the radiation employer. Ordinary workers should respect exclusion and report uncertainty, rather than measure, move or recover a source themselves.

Lesson 15

Recognise radon as a different assessment route

Assess the workplace's radon potential and obtain suitable measurement and competent follow-through where indicated.

Read the workface decision

Radon is a naturally occurring radioactive gas and cannot be assessed by smell or by looking around the room. Its workplace assessment is different from coordinating a sealed-source testing operation. Location, below-ground spaces and representative measurement may matter. Where results require action, use appropriate specialist advice, mitigation and verification; do not substitute a generic construction walkaround for that process.

Visual practice · Recognise radon as a different assessment route

Inspector beside a closed industrial X-ray inspection cabinet
SHAREhub photographic illustration · Inspector beside a closed industrial X-ray inspection cabinet. Use the written case for the exercise; this image does not prove a defect or safe system.
Read the workface decision

Radon is a naturally occurring radioactive gas and cannot be assessed by smell or by looking around the room. Its workplace assessment is different from coordinating a sealed-source testing operation. Location, below-ground spaces and representative measurement may matter. Where results require action, use appropriate specialist advice, mitigation and verification; do not substitute a generic construction walkaround for that process.

What is the ordinary employer workflow for workplace radon?

Check the premises and occupancy, measure where the assessment requires it, interpret annual average results for each relevant location, and act on elevated results. An area map alone cannot tell you the concentration inside a room. For several NI measurements, HSENI instructs the employer to notify using the highest annual average when notification is required.

Evidence to establish at the workface

Keep unauthorised people out and require an explicit completion or abnormal-condition handback; a testing case being closed or a machine becoming quiet is not a release signal.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What is the ordinary employer workflow for workplace radon?

Check the premises and occupancy, measure where the assessment requires it, interpret annual average results for each relevant location, and act on elevated results. An area map alone cannot tell you the concentration inside a room. For several NI measurements, HSENI instructs the employer to notify using the highest annual average when notification is required.

HSE advises testing workplaces in radon affected areas unless a detailed assessment gives good reason to expect low levels. Occupied below-ground workplaces need assessment and measurements irrespective of the map designation. Its guidance includes below-ground places used for more than about an hour a week or 50 hours a year, or containing an open water source; those examples are screening guidance, not an exemption or safe-exposure allowance. For Northern Ireland, assess the premises under the Ionising Radiations Regulations (Northern Ireland) 2017 (IRRNI17). HSENI instructs employers with several measurements to use the highest annual average for its notification decision; follow HSENI’s radon notification guidance when applicable. The cited HSE basement examples are GB guidance, not NI exemptions.

From screening to verified control
StageDecision or actionEvidence
Screen and planIdentify occupied rooms, basement tasks, contractor visits, building use and ventilation. Agree representative locations and a suitable measurement method with the provider.Premises plan, occupancy information, provider instructions and reasons for locations.
Measure and interpretFollow placement and duration instructions. Use the provider’s annual-average interpretation, including any applicable seasonal correction. A brief consumer-monitor reading is not automatically an annual average.Detector identities, dates, room conditions and the interpreted report.
Act on elevated resultsAbove 300 Bq/m³ annual average, apply the applicable GB or NI ionising-radiation duties. Consult a suitable RPA, address notification and restrict exposure as needed while remediation is arranged.Advice, regulator notification, interim arrangements, owner and timescale.
Remediate and verifyChoose building-specific engineering controls with a specialist. Maintain them, remeasure and review occupancy only on evidence that controls work.Installation and commissioning records, post-work results and authorised hand-back.
ReviewSet a justified review and remeasurement plan. Reassess after building, ventilation or occupancy changes or failed controls; there is no universal annual testing rule.Risk assessment, maintenance plan, review triggers and action closure.

If a result is close to 300 Bq/m³, or its averaging period or uncertainty is unclear, ask the measurement provider and RPA to interpret it. The legislation says exceeding 300; some HSE notification examples describe results at or above it. Do not treat a borderline report as automatic clearance. HSE radon in the workplace and HSE work requiring notification provide the GB operational guidance; HSENI supplies the NI notification route.

Evidence to establish at the workface

Keep unauthorised people out and require an explicit completion or abnormal-condition handback; a testing case being closed or a machine becoming quiet is not a release signal.

Apply the learning

A basement workplace is declared free of radon risk because no radiography source is present.

Decision and explanation

Assess the workplace's radon potential and obtain suitable measurement and competent follow-through where indicated.

Radon is a naturally occurring radioactive gas and cannot be assessed by smell or by looking around the room. Its workplace assessment is different from coordinating a sealed-source testing operation. Location, below-ground spaces and representative measurement may matter. Where results require action, use appropriate specialist advice, mitigation and verification; do not substitute a generic construction walkaround for that process.

Lesson 16

Protect against optical radiation and UV

Control the actual artificial and solar exposure routes with appropriate separation, work planning and protection.

Read the workface decision

The word radiation covers different hazards and controls. Welding light and solar UV are not the same task as ionising radiography or radon. Identify the source, route and affected body tissues, then use the appropriate competent assessment. Screens, working position, shade, scheduling and suitable protection have roles according to the task; one symbol or one type of PPE is not a universal solution.

A realistic eye with lids, lashes and a hazel iris beside an enlarged side cutaway showing the cornea, lens, inner retinal lining and optic nerve.View full detail ↗
The eye: surface and cutaway

Compare the visible eye with its enlarged side cutaway. Locate the clear front, lens and inner rear lining before following light and visual signals.

Distinguish the protective eye surface from the internal visual pathway. What task-specific protection or workstation change does this lesson require?

educational illustration · healthy anatomy; enlarged details and teaching colours.

Visual practice · Protect against optical radiation and UV

Actual SHAREsimulate construction model context: Specialist radiation work is not coordinated
Actual SHAREsimulate model capture · Specialist radiation work is not coordinated. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Read the workface decision

The word radiation covers different hazards and controls. Welding light and solar UV are not the same task as ionising radiography or radon. Identify the source, route and affected body tissues, then use the appropriate competent assessment. Screens, working position, shade, scheduling and suitable protection have roles according to the task; one symbol or one type of PPE is not a universal solution.

How can the ISO 45001 hierarchy of controls reduce risks while servicing a UV-curing cabinet?

How can the hierarchy of controls reduce risks while servicing a UV-curing cabinet? Assessment should identify source, wavelength, exposure route, access, duration, vulnerable workers and maintenance conditions.How should optical radiation be assessed and controlled? — part 1 of 3Learning point: Compare the named situations, controls and evidence together. Use the actual task assessment and the linked sources within their jurisdiction.How should optical radiation be assessed and controlled? — part 2 of 3How should optical radiation be assessed and controlled?

Evidence to establish at the workface

Coordinate specialist work before it starts: identify the source, adjacent occupancy, routes and levels, and ensure appropriate competent radiation protection advice and required authorisation.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How can the ISO 45001 hierarchy of controls reduce risks while servicing a UV-curing cabinet?

Assessment should identify source, wavelength, exposure route, access, duration, vulnerable workers and maintenance conditions.

For most ordinary light sources, no complex assessment is needed. The work becomes more serious where there are hazardous artificial optical radiation sources, outdoor UV exposure, high-power lasers, UV lamps, welding arcs or equipment that becomes hazardous during maintenance. The assessor should include normal operation, cleaning, alignment, adjustment, fault-finding and foreseeable misuse.

The hierarchy of control still applies. Enclosure, interlocking, remote operation, shielding, restricted access, safe viewing windows, signage and competent maintenance usually come before PPE. For outdoor UV, the control route is work planning: shade, timing, clothing, hats, sunscreen, drinking water, worker information and checking that the controls are realistic for the job.

A cabinet must be inspected and returned to use. Distinguish isolated maintenance from any authorised energised test and assess the actual lamp spectrum and exposure pathway.

How can the ERICPD hierarchy of controls reduce risks while servicing a UV-curing cabinet?

ERICPD is a planning crossmap. Its prompts do not add a sixth rung or rank Isolate above engineering. Discipline verifies and sustains every control level.

Control levelControl for this activityOwner and verificationStop / restart decision
EliminateUse external diagnostics or a validated non-UV curing process where that removes exposed UV work.

Basis: HSE optical radiation

Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere.If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
Reduce, including substitutionEvaluate a suitable lower-emission process or lamp system through process and optical-radiation assessment; changed wavelength is not automatically safer.

Basis: HSE optical radiation

Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted.Reject an alternative if its performance is unproved or its new hazards are unresolved.
IsolateIsolate the lamp supply and other hazardous energy before access and restrict the test area for any necessary authorised functional check.

Basis: HSE optical radiation

Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access.Hold or stop for unplanned energisation, damaged shielding, defeated interlock or an unassessed lamp change.
Control: physical safeguardsMaintain suitable enclosures, interlocks and wavelength-appropriate viewing protection; verify that access cannot expose people to hazardous radiation.

Basis: HSE optical radiation

Competent equipment/process owner checks lamp identity/spectrum, isolation, enclosure, viewing protection and interlock test.Hold or stop for unplanned energisation, damaged shielding, defeated interlock or an unassessed lamp change.
Control: work method and responseUse the approved service/test procedure and define who may energise the source, the test boundary and the acceptance criteria.

Basis: HSE optical radiation

Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity.Hold work when the agreed limits, competent cover or effective communication cannot be maintained.
PPESelect task-specific eye/face and skin protection from competent assessment. Ordinary clear glasses are not universal UV protection.

Basis: HSE optical radiation

Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence.Do not use unsuitable protection or rely on PPE to continue after an essential source control fails.
DisciplineTest interlocks and the restored enclosure and record lamp or configuration changes before production accepts the cabinet.

Basis: HSE optical radiation

Release only after competent service and optical-risk owners accept the restored protective functions. Retain verification and unresolved restrictions at handover.Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.

How can the ISO 45001 hierarchy of controls reduce risks while servicing a UV-curing cabinet?

The hierarchy of controls in ISO 45001:2018 comes under Clause 8.1.2 (Eliminating hazards and reducing OH&S risks), which is located within Clause 8 ("Operation").

ESEAP: Elimination, Substitution, Engineering controls, Administrative controls and PPE. Control order: HSE hierarchy of controls and IOSH hierarchy of control guidance.

Control levelControl for this activityOwner and verificationStop / restart decision
EliminationUse external diagnostics or a validated non-UV curing process where that removes exposed UV work.

Basis: HSE optical radiation

Task owner verifies that the proposed change removes the named hazardous step, including foreseeable cleaning, maintenance and work transferred elsewhere.If the hazardous step remains, keep it within the task assessment and select the stronger feasible remaining controls.
SubstitutionEvaluate a suitable lower-emission process or lamp system through process and optical-radiation assessment; changed wavelength is not automatically safer.

Basis: HSE optical radiation

Competent task/process owner validates suitability, compatibility and new hazards against the actual operating requirements before the alternative is adopted.Reject an alternative if its performance is unproved or its new hazards are unresolved.
Engineering controlsIsolate the lamp supply and other hazardous energy before access and restrict the test area for any necessary authorised functional check.

Basis: HSE optical radiation

Supervisor checks the actual boundary, affected people and connected work; verify separation or isolation before allowing access.Hold or stop for unplanned energisation, damaged shielding, defeated interlock or an unassessed lamp change.
Engineering controlsMaintain suitable enclosures, interlocks and wavelength-appropriate viewing protection; verify that access cannot expose people to hazardous radiation.

Basis: HSE optical radiation

Competent equipment/process owner checks lamp identity/spectrum, isolation, enclosure, viewing protection and interlock test.Hold or stop for unplanned energisation, damaged shielding, defeated interlock or an unassessed lamp change.
Administrative controlsUse the approved service/test procedure and define who may energise the source, the test boundary and the acceptance criteria.

Basis: HSE optical radiation

Supervisor confirms the work limits, competent cover, communication and stop/restart authority with the people doing this activity.Hold work when the agreed limits, competent cover or effective communication cannot be maintained.
PPESelect task-specific eye/face and skin protection from competent assessment. Ordinary clear glasses are not universal UV protection.

Basis: HSE optical radiation

Assessor confirms whether personal protection is needed and checks suitability, condition, compatibility and any required fit evidence.Do not use unsuitable protection or rely on PPE to continue after an essential source control fails.
Administrative controlsTest interlocks and the restored enclosure and record lamp or configuration changes before production accepts the cabinet.

Basis: HSE optical radiation

Release only after competent service and optical-risk owners accept the restored protective functions. Retain verification and unresolved restrictions at handover.Keep the task on hold until required reinstatement evidence and unresolved defects are accepted by the responsible owner.

For the actual task hazard, HSE places elimination first, then substitution, engineering controls, administrative controls and suitable PPE for residual risk. Record why a higher control is not practicable and how the chosen measure is checked in use. HSE hierarchy of controls

Task hazardEliminate, substitute and engineerSelection, owner and performance checkFailure, stop and direct sources
Welding arc UV reaching the operator or bystanderEliminate an unnecessary arc process or use a lower-exposure joining method where feasible. Fit opaque welding screens and controlled bays; arrange the task so other workers cannot view the arc.Welding lead checks screen coverage, gaps, adjacent routes and eyewear/skin protection before striking an arc; verify equipment selection and condition.Stop welding if the screen is moved, an unprotected person enters or eye/skin symptoms occur; restore separation and review exposure. HSE welding health risks HSE five-level hierarchy
UV curing or germicidal lamp during cleaning or maintenanceEliminate open-lamp access through an enclosed process; choose a lower-exposure method if validated for the task. Interlock doors and isolate energy for maintenance.Competent engineer commissions enclosure/interlock, checks lamp specification and tests isolation before access; retain measured or manufacturer exposure evidence where needed.Do not operate with a bypassed interlock, missing cover or unknown replacement lamp; isolate, repair and retest. HSE optical radiation overview HSE optical radiation law
Laser beam during alignment or repairAvoid open-beam alignment where possible; enclose beam path, fit interlocks and remote viewing, then restrict authorised access.Laser safety lead verifies class, beam path, shutter/interlock and correct wavelength-specific eyewear for residual open-beam work; record task authorisation.Stop alignment for damaged enclosure, failed interlock, uncertain laser class or wrong eyewear; competent lead revalidates before return. HSE lasers HSE optical radiation law
Long outdoor solar UV exposureSchedule to reduce peak sun where feasible and provide shade; use clothing and brimmed head protection before sunscreen for uncovered skin.Supervisor checks shade, shift duration, clothing and worker feedback; remind workers to seek clinical review for changing skin lesions.Change task or provide shelter if shade/clothing cannot be used or a worker develops heat or skin concern; solar UV is not governed by AOR 2010. HSE outdoor workers and sun exposure

Evidence to establish at the workface

Coordinate specialist work before it starts: identify the source, adjacent occupancy, routes and levels, and ensure appropriate competent radiation protection advice and required authorisation.

Apply the learning

A welding screen is moved, exposing a passing trade, while outdoor workers have no sun-protection arrangement.

Decision and explanation

Control the actual artificial and solar exposure routes with appropriate separation, work planning and protection.

The word radiation covers different hazards and controls. Welding light and solar UV are not the same task as ionising radiography or radon. Identify the source, route and affected body tissues, then use the appropriate competent assessment. Screens, working position, shade, scheduling and suitable protection have roles according to the task; one symbol or one type of PPE is not a universal solution.

Lesson 17

Capstone: plan a mixed exposure shift

Coordinate task sequencing and source controls, representative exposure assessment, exclusion and clear communication before work starts.

Read the workface decision

A mixed shift needs both topic-specific controls and interface management. Noise may hide an exclusion warning, a haul-road change may increase shocks, and workers may use several vibrating tools. Keep the assessments distinct enough to be valid, then connect them through the programme and workface plan. Assign owners and check the assumptions as the work changes.

Visual practice · Capstone: plan a mixed exposure shift

Inspection of a hand-held breaker and vibration sensor
SHAREhub photographic illustration · Inspection of a hand-held breaker and vibration sensor. Use the written case for the exercise; this image does not prove a defect or safe system.
Read the workface decision

A mixed shift needs both topic-specific controls and interface management. Noise may hide an exclusion warning, a haul-road change may increase shocks, and workers may use several vibrating tools. Keep the assessments distinct enough to be valid, then connect them through the programme and workface plan. Assign owners and check the assumptions as the work changes.

What makes a vibration risk assessment suitable and sufficient?

Identify exposed people and tasks, estimate daily exposure from representative magnitude and duration, compare with the correct values, select controls, record actions and review effectiveness. Start with observation and worker consultation, not paperwork alone. Describe equipment, material, process, work pattern, environment, maintenance, symptoms and groups who may be more vulnerable.

Evidence to establish at the workface

Maintain road surfaces and drainage, repair potholes and establish appropriate operating speeds and safe alternatives when weather or works degrade the route.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

What makes a vibration risk assessment suitable and sufficient?

Identify exposed people and tasks, estimate daily exposure from representative magnitude and duration, compare with the correct values, select controls, record actions and review effectiveness.

Start with observation and worker consultation, not paperwork alone. Describe equipment, material, process, work pattern, environment, maintenance, symptoms and groups who may be more vulnerable. Decide whether exposure can be avoided. Where it remains, make a reasonable estimate good enough to distinguish low, action-level and limit-level decisions. Record uncertainty and the evidence needed to resolve it. See legislation.gov.uk.

StepOutput
IdentifyPeople, tasks, sources, conditions and health signals. Source
EstimateRepresentative HAV or WBV daily exposure and uncertainty. Source
Decideexposure action value (EAV) / exposure limit value (ELV) status, risk-control and health route. Source
Act and verifyNamed actions, field checks, exposure/health feedback and review. Source

Basis: Control of Vibration at Work Regulations 2005; Control of Vibration at Work Regulations (Northern Ireland) 2005; HSE Vibration risk assessment; HSE L141 Whole-body vibration

Evidence to establish at the workface

Maintain road surfaces and drainage, repair potholes and establish appropriate operating speeds and safe alternatives when weather or works degrade the route.

Apply the learning

Breaking, dumper runs and specialist radiography are scheduled together beside an occupied workface.

Decision and explanation

Coordinate task sequencing and source controls, representative exposure assessment, exclusion and clear communication before work starts.

A mixed shift needs both topic-specific controls and interface management. Noise may hide an exclusion warning, a haul-road change may increase shocks, and workers may use several vibrating tools. Keep the assessments distinct enough to be valid, then connect them through the programme and workface plan. Assign owners and check the assumptions as the work changes.

Lesson 18

Use evidence to make one real improvement

Assign a measurable control improvement and verify its effect with suitable exposure and workface evidence.

Read the workface decision

Good evidence includes the conditions, people, tasks, controls and decision limits, rather than a collection of numbers detached from the job. Combine competent exposure information with observations and worker feedback. Respect health confidentiality and use the appropriate specialist route when uncertainty remains. Course completion supports informed participation; it does not confer competence to conduct specialist radiation work, diagnose illness or certify a noise-control design.

Visual practice · Use evidence to make one real improvement

Actual SHAREsimulate construction model context: Noise masks warnings beside the plant route
Actual SHAREsimulate model capture · Noise masks warnings beside the plant route. The exercise description supplies the scenario; a still image cannot establish hidden conditions.
Read the workface decision

Good evidence includes the conditions, people, tasks, controls and decision limits, rather than a collection of numbers detached from the job. Combine competent exposure information with observations and worker feedback. Respect health confidentiality and use the appropriate specialist route when uncertainty remains. Course completion supports informed participation; it does not confer competence to conduct specialist radiation work, diagnose illness or certify a noise-control design.

How should a buy-quiet decision be specified and verified?

Compare equipment for the intended work and verify the installed result; a supplier emission figure alone does not establish a worker's daily exposure. Consider a workshop replacing a noisy compressed-air cleaning step. The buyer describes the material, production rate, operator position and cleaning quality needed.

Evidence to establish at the workface

Assess representative daily or appropriate weekly exposure and separate peaks for exposed people. Select hearing protection for the actual task, fit and PPE compatibility and provide required hearing surveillance.

Try the optional visual exercise in the interactive course, then complete the required lesson decision.

How should a buy-quiet decision be specified and verified?

Compare equipment for the intended work and verify the installed result; a supplier emission figure alone does not establish a worker's daily exposure.

Consider a workshop replacing a noisy compressed-air cleaning step. The buyer describes the material, production rate, operator position and cleaning quality needed. Compare feasible methods that remove or reduce the noise-producing step, and assess any new hazards, rather than comparing only the price of a similar noisy nozzle. See HSE buy quiet guidance.

Ask suppliers about the conditions behind their noise information and the likely behaviour in the intended installation. Different test arrangements or operating loads may make headline figures unsuitable for direct comparison. The competent assessor considers exposure from the whole task and other machines, including the people nearby; a machine emission value is not automatically a personal daily exposure value. See HSE noise risk assessment.

At acceptance, verify that the alternative does the required job, its source controls are installed correctly and exposure evidence represents actual production. Record the selected option, rejected alternatives and residual safeguards. If the agreed performance is not demonstrated, keep the affected acceptance open and correct the design or method rather than treating new equipment as inherently quiet. See HSE noise risk assessment. Also see HSE buy quiet guidance.

Decision basis: HSE buy quiet guidance. HSE noise risk assessment. The scenario and suggested records are illustrative; apply the source within its stated jurisdiction and the assessed work.

Evidence to establish at the workface

Assess representative daily or appropriate weekly exposure and separate peaks for exposed people. Select hearing protection for the actual task, fit and PPE compatibility and provide required hearing surveillance.

Apply the learning

An action says raise awareness but no one can show whether the changed cutting method reduced exposure or improved warning audibility.

Decision and explanation

Assign a measurable control improvement and verify its effect with suitable exposure and workface evidence.

Good evidence includes the conditions, people, tasks, controls and decision limits, rather than a collection of numbers detached from the job. Combine competent exposure information with observations and worker feedback. Respect health confidentiality and use the appropriate specialist route when uncertainty remains. Course completion supports informed participation; it does not confer competence to conduct specialist radiation work, diagnose illness or certify a noise-control design.