SHARE Knowledge Hub

Noise Risk Assessment and Hearing Conservation

A noise risk assessment estimates representative daily or weekly exposure and separate peaks, identifies who is at risk, and turns measurements into an owned control and hearing-conservation plan. Hearing tests and protectors support source reduction.

Updated 2026-11-11UK focus

Understanding Noise Risk Assessment and Hearing Conservation

A noise risk assessment is a decision record about who is exposed, to what daily or weekly dose and C-weighted peak, what must be controlled, and how hearing will be conserved.

Why this matters at work

Use the HSE calculator or the correct energy formula with actual task durations and include all material noise, shifts and peaks. Record the source data, observations, assumptions and uncertainty so the calculation can be checked. Compare unattenuated exposure with action values; assess the exposure limit separately using credible protector performance where appropriate. Even suitable protection would not remove the need for a planned source-control programme. If the durations or operating conditions are uncertain, obtain better evidence rather than presenting a precise result without its limits.

Plan acceptance after installation with neighbouring plant and auxiliaries operating as intended. Check access, maintenance and foreseeable open-door interventions as well as normal running. Compare the measured or competently estimated exposure with the procurement requirement and the pre-installation baseline, and record any conditions not tested. If a benefit depends on an enclosure staying shut, demonstrate that the work can be performed that way. Assign repairs or further controls before closing acceptance. Quieter procurement can prevent embedded exposure, but a catalogue claim does not remove the employer’s assessment or ongoing maintenance duties.

How organisations manage this in practice

Observe whether the work can be done with the control in its intended state, including loading, cleaning and fault recovery. Check that ventilation, guarding and maintenance remain suitable and that noise has not simply moved to another worker. Keep the test conditions, results, limitations and outstanding actions with the assessment. Assign ongoing inspection and maintenance and review after plant or production changes. Closing an engineering project requires both evidence of installation and evidence of reduced exposure in use; a purchase invoice, photograph or brief quiet demonstration is not enough.

Define the decisions: which people may be at risk, the tasks and operating states, the daily or weekly exposure and peaks, and what control or surveillance decisions are needed. Include ordinary and foreseeable high-demand work, maintenance, startup, overtime and nearby workers. Choose representative sampling periods and locations rather than the easiest quiet moment. Agree instrument and calibration requirements, task timing observations, the handling of variability and uncertainty, and how workers will be consulted. Retain enough raw and contextual information to understand which work a result represents. If production is unusually low, state the limitation and arrange further evidence; do not silently extrapolate a favourable period to all shifts. Require an action-oriented report identifying priorities and follow-up checks. Competence means being able to interpret the work and evidence, not merely operate a meter. Review the assessment when sources, durations, layout or relevant worker needs change.

Operators report that a press sounds louder after a tooling change. The supervisor asks engineering to check the source and a competent assessor to review exposure. The team checks the engineering change during production and confirms remaining protection is suitable.

Noise: source, transmission path and the worker’s hearing: illustrative 3D equipment and the people who may be affected
Interactive 3D explainerSHAREsim

Noise: source, transmission path and the worker’s hearing

Explore how this equipment can harm its users and other people, then follow the practical measures that interrupt each pathway. This is a hazards and good-practice lesson; the separate checklist remains the pre-use/safety-check activity.

Checksheets and risk assessments

Equipment checksheets

Risk assessment forms

Risk assessment examples

Forms and tools

Full written walkthrough — all 8 steps
  1. 1. Identify the source and exposed people

    What is happening: The machine is one possible sound source; the observer, adjacent stations and other tasks also matter.

    How harm can occur: Noise can damage hearing, cause tinnitus and mask warnings or communication.

    Best practice to apply: Observe the real work and affected people and identify the sources that dominate their exposure.

    Why this works: Treating a minor source while a dominant one remains may give little benefit to the worker.

    Noise at Work · Why is noise harmful?
  2. 2. Reduce the source before relying on PPE

    What is happening: The enclosure illustrates one engineering approach; source process and equipment choices come first.

    How harm can occur: Unnecessary noisy work continues to expose people even if they carry hearing protection.

    Best practice to apply: Consider quieter processes, equipment, maintenance and suitable source treatments before lower-order measures.

    Why this works: Source reduction benefits everyone exposed and does not depend solely on individual wearing behaviour.

    Noise at Work · How can the ISO 45001 hierarchy of controls reduce workplace noise at source and protect hearing?
  3. 3. Understand openings and transmission paths

    What is happening: A barrier or enclosure changes a path but sound can still travel through gaps and other routes.

    How harm can occur: An opening, reflection or untreated path can leave the worker exposed despite a visible screen.

    Best practice to apply: Use competent acoustic design and verify the actual arrangement, including access and necessary ventilation.

    Why this works: A screen's appearance does not show attenuation at the person; the complete route matters.

    Noise at Work · What failure chains cause avoidable exposure?
  4. 4. Include the person and the full work pattern

    What is happening: A person's exposure changes with tasks, location and duration.

    How harm can occur: A short loud event or several jobs can be missed by a single convenient reading.

    Best practice to apply: Assess representative daily/weekly and peak exposure where appropriate and include all relevant work.

    Why this works: The assessment must describe the person's work, not only one machine's catalogue number.

    Noise at Work · How do daily and peak exposure differ?
  5. 5. Measure for a decision, not a decorative number

    What is happening: The meter and dosimeter show that method, placement and interpretation are part of measurement.

    How harm can occur: An unrepresentative or poorly interpreted result can lead to ineffective protection and continued harm.

    Best practice to apply: Use suitable competent measurement and compare with the applicable GB or NI framework; no reading is supplied here.

    Why this works: A valid result needs an appropriate method and context, not merely an instrument on site.

    Noise at Work · What should be checked before and after a noisy task?
  6. 6. Plan hearing protection for residual risk

    What is happening: The protection station is separate from the source and path controls.

    How harm can occur: Unsuitable fit, selection or use can leave hearing unprotected; overprotection can also hinder essential awareness.

    Best practice to apply: Select suitable protection, fit, instruction and use arrangements while continuing practicable source reduction.

    Why this works: Residual protection complements engineering and must work for the actual person and task.

    Noise at Work · Who must be able to do what?
  7. 7. Use surveillance to prevent further harm

    What is happening: Health surveillance and symptom reports support prevention rather than making exposure acceptable.

    How harm can occur: Progressive hearing change may be unnoticed while exposure continues.

    Best practice to apply: Use the required competent health-surveillance arrangements and act on findings and reported symptoms.

    Why this works: Finding harm should drive review and control, not be treated as an acceptable cost of work.

    Noise at Work · What record and review cycle makes the programme accountable?
  8. 8. Verify changes at the worker

    What is happening: New machinery, layout, open doors or altered production can change the noise reaching people.

    How harm can occur: A nominal treatment can lose effectiveness during real work or transfer exposure to someone else.

    Best practice to apply: Verify actual improvement, keep controls maintained and review changed work and affected groups.

    Why this works: A successful intervention improves exposure during use rather than only completing a purchase or record.

    Noise at Work · How could a workshop replace a noisy blow-off step?

Illustrative awareness learning. Geometry, colours and movement do not establish safe distances, capacity, exposure, isolation or work permission. Use the actual assessment, equipment information and competent arrangements.

The wider workplace has its own account and subscription access. Exploring this lesson does not grant access, record course completion or authorise work.

UK guidance for further reading

HSE: Noise
SHAREsimulate

How can I practise this topic in 3D?

Panel beating and pneumatic-tool noise
3D workplace practiceSHAREsim

Panel beating and pneumatic-tool noise

Noise masks warnings beside the plant route
3D workplace practiceSHAREsim

Noise masks warnings beside the plant route

High noise during glass sorting
3D workplace practiceSHAREsim

High noise during glass sorting

All related inspection points 3 across 3 locations
Garage workshop 1 inspection point
Construction site 1 inspection point
Recover materials. Protect people. 1 inspection point

Practice in the SHAREhub environment. Browser practice is separate from workplace competence and formal learning records.

What must the assessment decide?

It must identify affected people, a reliable exposure estimate, action-value comparison, control plan and surveillance eligibility.

Write down the machine and task modes, sound level, actual duration, impulses, nearby exposures, existing controls, uncertainty, action owner and deadline. HSE explicitly says risk assessment is more than taking measurements; sometimes existing reliable data suffice, while a variable process needs a competent survey. HSE assessment guidance.

A working day contains unequal noise contributions

Combine representative task levels with their durations using an appropriate energy-based method. Keep peak sound pressure separate; an arithmetic average of decibel readings is not a daily exposure calculation.

Sound level measurement at a UK industrial workplace. Photorealistic illustration.
Illustrative UK workplace scene. Read the practical checks below for responsibilities, evidence and limits. Download image · Download smaller image
  1. Task level

    Use suitable representative measurements and record the task and operating conditions; do not invent levels from equipment appearance.

  2. Duration

    Include the actual time spent at each task and relevant variation through the shift.

  3. Energy contribution

    Use the HSE calculator or another competent method to combine the level-duration contributions. Decibels are logarithmic.

  4. Daily exposure

    Record the result, assumptions and uncertainties for the assessed day; distinguish representative daily or weekly assessment as applicable.

  5. Peak assessed separately

    Assess peak sound pressure separately from energy-equivalent exposure; a short event is not automatically negligible.

  6. Uncertainty

    Identify missing tasks, variable work and measurement limits. Resolve material gaps before relying on the result.

  7. Recheck after change

    Use the result to improve source controls, protection and surveillance arrangements; verify the revised work rather than just filing the number.

The timeline uses qualitative task blocks and provides no measured levels, new legal threshold or automatic safe badge. Use current official guidance for the assessment.

What do dB(A), dB(C) and L_EX,8h mean?

A-weighting is used for daily or weekly exposure, C-weighting for peak sound pressure, and L_EX,8h is an energy-equivalent daily exposure.

What do dB(A), dB(C) and L_EX,8h mean?

What do dB(A), dB(C) and L_EX,8h mean?. Relationship map from the current topic. Read the linked sources within their subject and jurisdiction.
Learning point: Relationship map from the current topic. Read the linked sources within their subject and jurisdiction.
Read the complete visual as text
  1. A-weighting is used for daily or weekly exposure, C-weighting…: A-weighting is used for daily or weekly exposure, C-weighting for peak sound pressure, and L_EX,8h is an energy-equivalent daily exposure.
  2. Do not average decibels arithmetically. For equal-duration tasks, an…: Do not average decibels arithmetically. For equal-duration tasks, an 88 dB(A) task contributes twice the sound energy of an 85 dB(A) task. An illustrative eight-hour day with four hours at 88 dB(A) and four at 82 dB(A) is about 86.0 dB(A); this is a teaching estimate, not a site measurement. The louder four-hour task dominates the energy total; four quieter hours cannot cancel it. Record the measured task levels and times before choosing the source-control priority. On these assumptions, 86.0 dB(A) exceeds the 85 dB(A) upper action value: the employer needs a planned technical or organisational reduction, suitable protection and zoning where needed during control work, and indicated hearing surveillance. The C-weighted peak and measurement uncertainty still need assessment. HSE noise duties . A high impulse still needs its separate C-weighted peak assessment. Use a competent assessor and L108 for the actual calculation. Sources: HSE noise employer duties .

Do not average decibels arithmetically. For equal-duration tasks, an 88 dB(A) task contributes twice the sound energy of an 85 dB(A) task. An illustrative eight-hour day with four hours at 88 dB(A) and four at 82 dB(A) is about 86.0 dB(A); this is a teaching estimate, not a site measurement. The louder four-hour task dominates the energy total; four quieter hours cannot cancel it. Record the measured task levels and times before choosing the source-control priority. On these assumptions, 86.0 dB(A) exceeds the 85 dB(A) upper action value: the employer needs a planned technical or organisational reduction, suitable protection and zoning where needed during control work, and indicated hearing surveillance. The C-weighted peak and measurement uncertainty still need assessment. HSE noise duties. A high impulse still needs its separate C-weighted peak assessment. Use a competent assessor and L108 for the actual calculation. Sources: HSE noise employer duties.

TaskUnrounded energy points
88 dB(A) for 4 hoursAbout 99.8
82 dB(A) for 4 hoursAbout 25.1
CombinedAbout 124.8 unrounded points; 85.96293 dB(A), about 86.0

This original calculation table uses energy contributions, not arithmetic averaging of decibels. The companion calculator rounds task points separately to a total of 125; the energy result remains about 86.0 dB(A). Open the existing calculator with its peak, method and uncertainty limits, and use the NIHL concern pathway for clinical escalation.

How is a defensible exposure estimate built?

Map tasks and variation, use reliable representative data, calculate full-shift exposure and document uncertainty and review triggers.

Sample normal and foreseeable worst operating modes, not only the quietest shift. Record meter type, calibration, location, duration and workers. Supplier sound-power or emission information cannot be copied straight into personal exposure; verify installed use. Weekly exposure can help where days vary, but assess a peak separately. If the estimate straddles an action value, improve the data and use protective controls while resolving uncertainty. Sources: HSE noise risk assessment, HSE L108 noise guidance (third edition, 2021).

So far as practicable, assess interactions between noise and ototoxic substances used at work, and between noise and vibration, as required by regulation 5(3)(c) in both jurisdictions. Record relevant chemical/process co-exposures and vibration, link the COSHH/vibration assessments and seek competent technical or occupational-health advice where needed. Do not infer causation from a worker’s medication list or place personal medical details in a noise survey.

Weekly averaging requires marked variation, a reasoned recorded justification and worker consultation; it must not increase risk or conceal a peak. See the companion calculator’s weekly-suitability explanation and L108 paragraphs 28–29 rather than assuming every variable day qualifies.

Where do hearing-conservation programmes fail?

A paper assessment without source changes, a protector chosen only from SNR, or audiometry without action can conceal ongoing harm.

An enclosure measured while empty may leak during production. A worker’s protector may lose seal with safety glasses. A high attenuation rating can impair warning detection; HSE advises avoiding protected levels below 70 dB at the ear. A threshold shift must prompt control review and clinical advice, not a presumption that the worker alone failed. Sources: HSE noise health surveillance.

How can the hierarchy of controls turn noise assessments into stronger exposure controls?

Rank source removal, quieter substitution and engineering ahead of time limits and hearing protectors; name an owner and acceptance measure.

How does the assessment become a control plan?

How does the assessment become a control plan?. Evidence map: these are the current topic’s explanation and conditions. Read the linked sources within their subject and jurisdiction.
Learning point: Evidence map: these are the current topic’s explanation and conditions. Read the linked sources within their subject and jurisdiction.
Read the complete visual as text
  1. Rank source removal, quieter substitution and engineering ahead of…: Rank source removal, quieter substitution and engineering ahead of time limits and hearing protectors; name an owner and acceptance measure.
  2. HSE prioritises eliminating and substituting hazards before engineering controls,…: HSE prioritises eliminating and substituting hazards before engineering controls, administrative controls and PPE, as explained in its five-level hierarchy of controls . SHARE uses ERICPD as a task-planning prompt: Eliminate; Reduce, including substitution; Isolate through engineered separation; Control with other engineered or administrative measures; PPE; and Discipline, meaning continued verification and maintenance. ERICPD is not a sixth HSE level or a separate legal duty. The example below is a feasibility test for this work, not a universal prescription.
  3. Select hearing protection for the measured spectrum and task.…: Select hearing protection for the measured spectrum and task. Fit, compatibility with other PPE, comfort, speech and warnings matter. An SNR shortcut is limited, especially for low-frequency noise; specialist frequency-band assessment may be needed. Record the residual risk and verify the source controls before relaxing zones or surveillance. Sources: HSE noise hearing protection , HSE over-protection guidance .

HSE prioritises eliminating and substituting hazards before engineering controls, administrative controls and PPE, as explained in its five-level hierarchy of controls. SHARE uses ERICPD as a task-planning prompt: Eliminate; Reduce, including substitution; Isolate through engineered separation; Control with other engineered or administrative measures; PPE; and Discipline, meaning continued verification and maintenance. ERICPD is not a sixth HSE level or a separate legal duty. The example below is a feasibility test for this work, not a universal prescription.

Select hearing protection for the measured spectrum and task. Fit, compatibility with other PPE, comfort, speech and warnings matter. An SNR shortcut is limited, especially for low-frequency noise; specialist frequency-band assessment may be needed. Record the residual risk and verify the source controls before relaxing zones or surveillance. Sources: HSE noise hearing protection, HSE over-protection guidance.

Read the practical categories separately: elimination removes the hazardous task/source; substitution replaces it with a suitable safer alternative; physical separation, containment and capture are engineering decisions. Duration/access/briefing are administrative measures, PPE covers residual exposure, and continued inspection, maintenance and verified action closure sustain the controls. Exposure monitoring or dosimetry measures exposure rather than protecting a person. The detailed text and records below distinguish these decisions; an overview illustration is not task authorisation.

When is hearing surveillance indicated and how is it used?

Provide regular hearing checks for workers regularly above the upper action value or otherwise at particular risk, under an occupational-health programme.

A baseline before exposure is useful where feasible. HSE describes a typical schedule, not an automatic fixed legal interval; a competent provider adapts checks to risk and findings. Workers receive results; employers retain health and fitness advice, while clinical records stay confidential. A change in audiometry prompts exposure and source-control review. HSE and HSENI describe the separate routes.

The occupational-health provider owns the surveillance schedule: obtain an early baseline, annual checks initially, then a risk-adjusted interval. HSE’s usual guidance is annual checks for the first two years and then three-yearly checks, with earlier review for abnormal findings or high risk. This is guidance, not an automatic statutory interval or a reason to delay symptom assessment.

How should a press shop reassess after a new production line?

A press shop measures the installed line at load, calculates day and peak exposure, then verifies an enclosure and hearing programme.

BuildOut Ltd · practical example

Assess a refurbishment crew's whole noise exposure

The key lesson Noise assessment must consider exposure across relevant activities, including peak noise; hearing protection does not remove the duty to reduce noise at source.

BuildOut Ltd would assess the crew's actual noise exposure, reduce noisy work at source and verify the residual hearing-protection and surveillance arrangements.

The situation: Alongside the press-shop example, consider a BuildOut refurbishment crew using cutting and breaking equipment at several work fronts. A short measurement beside one tool does not describe the whole shift or neighbouring workers' exposure.

Why this matters: People can accumulate exposure while moving between jobs or standing near someone else's noisy work, even when their own tool is quiet.

How BuildOut Ltd would manage it

  • Map the day's work — Site Manager. Identify noisy tasks, people nearby and how long activities actually occur. Include subcontractor work and changes in location rather than assessing each tool as if it operated alone.
  • Obtain useful evidence — Health and Safety Manager. Arrange competent assessment using representative exposure information and measurements where needed. Keep assumptions, operating conditions and uncertainty visible when comparing with the applicable requirements.
  • Reduce the source — Project Manager. Consider quieter processes and equipment, off-site preparation and separation of noisy operations. Check that changes reduce exposure without transferring the problem to another trade or creating new hazards.
  • Manage the remainder — Trade Supervisor. Implement the assessed hearing-protection arrangements and explain correct use, communication and warning signals. Resolve poor fit or incompatibility rather than simply recording that protection was issued.
  • Check the programme — Health and Safety Manager. Verify controls during work, review changes and arrange appropriate hearing health surveillance where indicated. Use relevant findings to improve controls while keeping individual health information confidential.

When the conditions change

Recognise the trigger
Work patterns change or the required noise controls cannot be maintained.
Make the immediate decision
Restrict affected noisy activity while the control or assessment gap is resolved.
Verify the next step
The Site Manager checks the revised task-duration assessment, quieter-method or separation controls and the required hearing-protection arrangements for the actual crew and nearby workers.

What good looks like

The assessment reflects the real shift and nearby work. Quieter choices and observed controls explain how exposure has been reduced, with residual protection properly supported.

Evidence to look for: Task and duration information, competent assessment, quieter-method review, field checks and appropriate surveillance arrangements.

Common mistake to avoid: Subtracting the ear defender's headline rating from a spot reading and calling the whole shift safe.

Apply this to your work: Whose noise exposure might be missed if you assess only the person operating the tool?

Guidance behind the management approach: HSE: employers' noise responsibilities. Use the topic's legal and technical guidance for the applicable work and location.

How should a press shop reassess after a new production line?

How should a press shop reassess after a new production line?. Relationship map from the current topic. Read the linked sources within their subject and jurisdiction.
Learning point: Relationship map from the current topic. Read the linked sources within their subject and jurisdiction.
Read the complete visual as text
  1. A press shop measures the installed line at…: A press shop measures the installed line at load, calculates day and peak exposure, then verifies an enclosure and hearing programme.
  2. Before: old measurements cover one press but the new…: Before: old measurements cover one press but the new schedule doubles stroke frequency. During: the assessor samples press cycles and positions; the engineer tests enclosure seals, and the supervisor logs time near the machine. The manager keeps hearing protection and access controls during validation. After: a repeat survey shows the actual reduction, occupational health reviews eligible workers and the action plan records the next trigger. A new die or removed panel reopens the assessment. Sources: HSE noise risk assessment , HSE noise health surveillance .
  3. Transfer to logistics maintenance: A mechanic uses an intermittent…: Transfer to logistics maintenance: A mechanic uses an intermittent impact tool during overtime while warehouse staff pass nearby. The assessor records each real task duration and position and assesses the separate C-weighted peak, rather than hiding the impulse in a quiet-shift average. The manager seeks a quieter tool or physical separation, keeps suitable interim protection and holds unrestricted work if the estimate or peak remains uncertain. A fresh representative measurement and observed layout check are the hand-back evidence. HSE noise risk assessment supports the decision method.

Before: old measurements cover one press but the new schedule doubles stroke frequency. During: the assessor samples press cycles and positions; the engineer tests enclosure seals, and the supervisor logs time near the machine. The manager keeps hearing protection and access controls during validation. After: a repeat survey shows the actual reduction, occupational health reviews eligible workers and the action plan records the next trigger. A new die or removed panel reopens the assessment. Sources: HSE noise risk assessment, HSE noise health surveillance.

Transfer to logistics maintenance: A mechanic uses an intermittent impact tool during overtime while warehouse staff pass nearby. The assessor records each real task duration and position and assesses the separate C-weighted peak, rather than hiding the impulse in a quiet-shift average. The manager seeks a quieter tool or physical separation, keeps suitable interim protection and holds unrestricted work if the estimate or peak remains uncertain. A fresh representative measurement and observed layout check are the hand-back evidence. HSE noise risk assessment supports the decision method.

How does this topic align with ISO 45001?

Use these examples to connect the relevant clauses to your own occupational health and safety management system. For each clause, identify the person responsible, the control in use and the evidence that it works.

Scroll across the table to read all four columns.

ISO 45001 clause alignment for Noise Risk Assessment and Hearing Conservation
ISO 45001 clauseHow it appliesWhat to put in placeHow to verify it works
6.1.2.2 Assessment of health and safety risksAssess noise across the working day, including loud individual tasks and workers nearby. BuildOut’s cutting and breaking jobs can contribute differently to each person’s exposure.Walk the job with the crew and record who does each task, the time spent on it and who works nearby. Use representative measurements where needed to evaluate daily exposure and peak noise.The assessment explains which activities, people and operating conditions the measurements represent. It identifies gaps to check when the programme or plant changes.
8.1.2 Hierarchy of controlsNoise reduction starts with the task or equipment, then addresses how sound reaches people.Review quieter methods or plant before the work starts. Separate noisy operations from other trades and apply suitable hearing protection for remaining exposure under the site arrangements.A comparison of feasible methods explains the chosen controls. Observations and repeat measurements where needed show how the changes affect the crew and nearby workers.
9.1.1 Monitoring and evaluating performanceA hearing conservation programme needs evidence that noise controls are still in place and reducing exposure.Assign checks for enclosure, separation and work sequencing, with repeat measurements when the earlier results no longer represent the job. Review suitable grouped occupational-health feedback where surveillance applies.Inspection and measurement records show where controls have drifted and whether fixes restored performance. The programme review considers anonymised feedback alongside exposure evidence.

Selected applications of ISO 45001:2018 with Amendment 1:2024. Use the current standard for a full assessment and check the legal duties that apply to the work and location.

ISO 45001:2018 · 2024 climate action amendment · ISO 45002 implementation guidance · ISO technical committee clause FAQ

Who must be able to do what?

A worker, supervisor, engineer, competent noise assessor and occupational-health professional have different decisions; a course certificate alone does not prove task competence.

Train for the actual machine, protection fit, hold point and reporting route. Observe the task and refresh after changed equipment or a failed control. The assessor needs sound and exposure competence; the occupational-health provider interprets audiometry and preserves medical confidentiality. The manager checks that a reported loss changes the control plan. Sources: HSE noise risk assessment, HSE noise health surveillance.

The assessor should show raw sampling, calibration, task durations, a separate peak decision and uncertainty; the manager should challenge whether those observations represent the current shift before signing the action plan.

RolePractical responsibilityEvidence and boundaryTraining and assessor checkReassess when
WorkerRecognise noisy tasks, wear selected protection, report tinnitus or control failure.Demonstrated fit and prompt report.Supervisor assesses: Observed protector fit, warning recognition and symptom reportNew tool, fit issue or symptom
SupervisorCheck method, enclosure and access before work; stop failed controls.Observed check and restart record.Operations manager assesses: Task briefing, enclosure check and stop/restart demonstrationChanged shift or failed control
Engineer / buyerReduce sound at source, validate quiet procurement and enclosure.Acceptance and maintenance measurements.Engineering lead assesses: Acoustic design review, quieter-equipment acceptance and maintenance checkNew plant, material or wear
Competent noise assessorPlan representative task, position and duration samples, separate peak assessment and uncertainty.Instrument calibration, raw observations, calculation, uncertainty and reasoned action-value conclusion.Technical lead witnesses sampling and checks the daily/weekly calculation and peak method.New line, shift pattern, impulse or uncertain estimate
Occupational healthRun indicated hearing surveillance and advise on concerning change.Fitness advice to employer; confidential medical detail retained clinically.Clinical lead assesses: Surveillance protocol and confidential interpretation reviewThreshold shift or altered exposure
Manager accepting the assessmentTest whether the sampled tasks represent actual work, fund source reduction and set interim controls.Signed acceptance of assumptions, priority actions, owners and remeasurement trigger.Senior dutyholder samples the field plan and closes actions only after measured control performance.Assumption fails, production changes or result straddles an action value

What record and review cycle makes the programme accountable?

Keep a source and exposure register, named action owners, verification results and triggers for reassessment.

HSE explains that a formal health and safety management system is optional. The employer must still plan, control, check and improve the measures for this task. Check that the survey represents production, overtime and peak tasks, and that each recommended source control has an owner, completion date and measured acceptance result.

What does the 86.0 dB(A) example establish and leave open?

It illustrates the energy combination of the stated tasks; actual exposure needs representative evidence, variation and uncertainty as well as a separate peak assessment.

The earlier example assumes four hours at 88 dB(A) and four at 82 dB(A). Its energy result is approximately 86.0 dB(A), rather than the arithmetic average of the two decibel numbers. It helps identify the louder task as an important control priority, but it is not a measurement of any real press shop or a prediction for a changed shift. See HSE noise risk assessment.

If the assessor learns that the louder task lasts longer during overtime or that a new production line operates simultaneously, the input evidence must be reviewed. Record what each level represents, where the person works, duration and relevant production conditions. Short favourable measurements should not be treated as a complete description of a variable job. See HSE L108 noise guidance (third edition, 2021).

A result near a decision value needs competent interpretation of uncertainty, not rounding down to avoid an action. Record the basis for the daily or justified weekly exposure approach and assess the C-weighted peak separately. Missing peak evidence is not supplied by the eight-hour energy calculation. HSE's GB guidance and the page's separate NI route must be used within their actual legal scope. See HSE noise employer duties.

Decision basis: HSE noise risk assessment. HSE L108 noise guidance (third edition, 2021). HSE noise employer duties. The scenario and suggested records are illustrative; apply the source within its stated jurisdiction and the assessed work.

How should an assessment show that a proposed control worked?

Specify what changes at source and verify representative exposure after installation, with clear ownership and remaining uncertainties.

For a press-shop enclosure proposal, identify the operating load, access configuration, other machines and people affected before measuring the change. The engineer accepts installation and functional safety; the competent noise assessor accepts the exposure evidence. A difference between two readings taken under different production conditions is not automatically evidence of the enclosure's effectiveness. See HSE buy quiet guidance.

Keep the action open when the intended operating condition has not been tested. Explain any interim protection and zoning in the assessed method, and check communication and compatibility with other PPE. Health surveillance can identify possible harm and prompt review, but it cannot replace source-control verification. See HSE noise risk assessment. Also see HSE noise health surveillance. Also see HSE noise hearing protection.

Decision basis: HSE buy quiet guidance. HSE noise risk assessment. The scenario and suggested records are illustrative; apply the source within its stated jurisdiction and the assessed work.

Which three numbers must not be confused?

A daily exposure value, a peak value and a hearing-protector rating answer different questions and need their own conditions and units.

Learning check: an assessor subtracts a box rating from the daily exposure and declares the source controlled. The learner should explain that the employer's source-reduction decision remains, and real protector effectiveness depends on selection, fit, use and the actual spectrum and conditions. Do not use an improvised arithmetic shortcut as a complete assessment. See HSE L108 noise guidance (third edition, 2021).

Learning check: a moderate daily result is used to dismiss a high impact event. The learner must request a suitable C-weighted peak assessment; short impulses are not characterised by an A-weighted average alone. Instrument method and competence must match that question. See HSE noise hearing protection. Also see HSE L108 noise guidance (third edition, 2021).

Ask the manager to locate the evidence, action owner and acceptance record, and the occupational-health route for findings. Keep personal audiometric information appropriately confidential. The programme should demonstrate a chain from task evidence to source control and continuing review, not simply a folder of survey reports. See HSE noise health surveillance.

Decision basis: HSE L108 noise guidance (third edition, 2021). HSE noise hearing protection. HSE noise health surveillance. The scenario and suggested records are illustrative; apply the source within its stated jurisdiction and the assessed work.

Which terms carry the key decisions?

Do not confuse a momentary sound level, full-day exposure and a peak value.

TermMeaningUse in this lesson
dB(A)A-weighted decibelsUsed for daily/weekly exposure.
dB(C)C-weighted decibelsUsed for peak sound pressure.
L_EX,8hDaily personal noise exposureEnergy-equivalent exposure normalised to eight hours.
EAVExposure action valueTriggers specified employer action.
ELVExposure limit valueMust not be exceeded; protection effect may be considered.
NIHLNoise-induced hearing lossSensorineural hearing impairment from harmful noise.
ACOPApproved Code of PracticeOfficial code with its own scope and legal context; distinguish it from legislation.
HSEHealth and Safety ExecutiveGreat Britain workplace regulator; use its guidance within scope.
HSENIHealth and Safety Executive for Northern IrelandNorthern Ireland workplace regulator; NI duties have separate instruments.
GBGreat BritainEngland, Scotland and Wales; distinguish the NI legal route.
NINorthern IrelandUse the Northern Ireland legislation and regulator route.
PPEPersonal protective equipmentResidual personal protection supporting stronger source controls.
ERICPDEliminate; Reduce; Isolate; Control; PPE; DisciplineSHARE planning prompt; Discipline means maintaining controls, not blame.
SNRSingle number ratingHearing-protector rating; assess actual fit, wearing and compatibility.