SHARE Knowledge Hub

Main health and safety duties for employers and workers

Employers must manage work risks and provide safe plant and systems so far as reasonably practicable. Workers must take reasonable care, cooperate with safety arrangements and raise defects; the applicable law differs between Great Britain and Northern Ireland.

Updated 2026-10-22Great Britain and Northern IrelandVersion 2.0

Owner: SHARE Knowledge Hub editorial team.

Understanding Main health and safety duties for employers and workers

Employers must manage work risks and provide safe plant and systems so far as reasonably practicable. Workers must take reasonable care, cooperate with safety arrangements and raise defects; the applicable law differs between Great Britain and Northern Ireland.

Why this matters at work

Avoid treating a numerical risk matrix as the law. A low-frequency exposure to potentially fatal harm may still require substantial measures. Review new technology or changing work methods, but do not wait for an injury before implementing known controls.

The strongest assurance combines a current risk assessment, implemented controls, field observation, maintenance records, worker accounts and management response. Absence of recorded injury is a lagging measure and does not prove a high-consequence hazard is controlled. Compare instructions with the task performed, check safeguards and welfare, ask workers whether reporting is effective, and review whether corrective actions were completed and tested. Use leading indicators tied to credible harm: overdue inspections, failed extraction tests, guard bypass, repeat near misses, training gaps, contractor interface failures and ageing risk actions. A high reporting rate may reflect trust and visibility, not necessarily worse safety. Management review should ask whether controls reduce exposure and what changed in plant, people or process. Assign an owner and date for each action and verify field effectiveness before closing it.

How organisations manage this in practice

Management Regulations require effective arrangements for planning, organisation, control, monitoring and review of preventive and protective measures; significant arrangements must be recorded at the threshold. Identify a competent owner for serious hazards and give that person authority, resources and access to decision-makers.

Review if the assessment is no longer valid or a significant change occurs; also use incidents, near misses, worker concerns and monitoring to trigger review. If fewer than five are employed, assessment and control duties still apply even though the statutory record threshold differs.

Section 2 requires every employer, so far as is reasonably practicable, to ensure the health, safety and welfare at work of all employees. It expressly includes safe plant and systems of work, safe use, handling, storage and transport of articles and substances, necessary information, instruction, training and supervision, a safe workplace and access or egress, and an adequate working environment and welfare facilities. Decide who controls purchasing, maintenance, task planning and supervision, and check that those people have sufficient authority and resources. Include visitors and contractors under the appropriate separate duty rather than assuming that only employees need protection.

Coordinate the failed tail-lift response

An operator reports the defect and prevents unsafe use; the employer arranges competent correction and a suitable alternative. Premises and contractor coordination may also be necessary.

Safety professional reviewing guidance and documents in a UK workplace office. Photorealistic illustration.
Illustrative UK workplace scene. Read the practical checks below for responsibilities, evidence and limits. Download image · Download smaller image
  1. Protect and report

    Stop affected unsafe use, maintain an assessed boundary and use the reporting arrangements.

  2. Resource the correction

    Arrange competent repair/verification and an assessed loading alternative; do not leave the operator to improvise.

  3. Coordinate duties

    Identify affected organisations and people with relevant duties and control, checking the applicable territory and law.

Delegating a task or receiving a report does not automatically discharge the employer’s duties.

What are the main health and safety duties?

Employers must identify and control risks created by work, provide safe plant and systems, and protect workers and others so far as reasonably practicable. Workers must take reasonable care, cooperate with the arrangements and raise dangerous shortcomings.

Great Britain and Northern Ireland

Great Britain and Northern Ireland. Great Britain: Use the Health and Safety at Work etc. Act 1974 and the applicable GB regulations. Identify HSE or the appropriate local authority according to activity and premises. Northern Ireland: Use the Health and Safety at Work (Northern Ireland) Order 1978 and the applicable NI regulations. Identify HSENI or the appropriate district council route. Status and specialist law: Check the actual person’s status, work and control, and any added specialist role. Do not decide disputed employment status, liability or protected disclosure from this map.
Learning point: Prevent the common error of treating the 1974 Act and every GB regulation as UK-wide. The relevant source scope and actual work conditions govern application.
Read the complete visual as text
  1. Great Britain: Use the Health and Safety at Work etc. Act 1974 and the applicable GB regulations. Identify HSE or the appropriate local authority according to activity and premises.
  2. Northern Ireland: Use the Health and Safety at Work (Northern Ireland) Order 1978 and the applicable NI regulations. Identify HSENI or the appropriate district council route.
  3. Status and specialist law: Check the actual person’s status, work and control, and any added specialist role. Do not decide disputed employment status, liability or protected disclosure from this map.

The legal starting point depends on place: the Health and Safety at Work etc. Act 1974 and Management Regulations 1999 apply in Great Britain (GB), while the Health and Safety at Work (Northern Ireland) Order 1978 and Management Regulations (Northern Ireland) 2000 are separate Northern Ireland (NI) routes. The same practical question runs through both: can people do the real task without avoidable harm? HSE health and safety law basics and HSENI making health and safety work for your business.

Managers and supervisors turn duties into decisions on resources, risk assessments, safe work, competence, emergency response and checking. A worker’s duty does not transfer the employer’s control responsibility to that worker. HSE employee health and safety duties and HSENI employees.

What harm can a duty failure cause?

A duty failure matters when it leaves a hazard uncontrolled at the point of work: a failed tail-lift, moving vehicle, unguarded machine or harmful exposure can injure workers and the public.

A paperwork-only assessment may say a lift is maintained while a defect remains in use; a rushed loading schedule may bring a pedestrian into the vehicle path. The harm chain is broken by equipment condition, route separation, competent use, clear stop authority and supervisor response. Occupational illness also develops when exposure and early reports are ignored. HSE risk assessment steps and HSE workplace transport.

How do duties turn into workplace controls?

Give each significant risk a control, owner, field check and escalation route. Ask workers whether the method works during routine and abnormal conditions.

Shared workplace control map

Shared workplace control map. Host and premises controller: Identify premises hazards, access, services and emergency interfaces. Exchange relevant risk information with contractors and other employers. Employer and contractor: Name who controls equipment, method, timing, people and supervision. Contractor appointment does not remove duties retained through actual control. Coordinate the interface: Map overlapping duties and a named owner for each control. An unclear safety-critical interface holds the affected activity until authority and protection are resolved.
Learning point: Show how employer, host, contractor, agency and premises controls overlap without leaving a gap. Schematic, not to scale; actual task-specific assessment and competent review govern.
Read the complete visual as text
  1. Host and premises controller: Identify premises hazards, access, services and emergency interfaces. Exchange relevant risk information with contractors and other employers.
  2. Employer and contractor: Name who controls equipment, method, timing, people and supervision. Contractor appointment does not remove duties retained through actual control.
  3. Coordinate the interface: Map overlapping duties and a named owner for each control. An unclear safety-critical interface holds the affected activity until authority and protection are resolved.

Risk assessment starts with real people, tasks and exposure, including contractors, visitors, agency workers and changes. Choose preventive measures; provide information, instruction, training and supervision; appoint competent help where needed. Check what happens during breakdown, cleaning, peak demand and handover. The employer retains accountability for the system even when specialists advise or workers cooperate. HSE legislation on leading health and safety and HSE risk assessment steps.

Duty-to-control evidence
Practical duty Workplace action Evidence and stop point
Assess risk Walk the loading task, identify lift, traffic and manual-handling hazards. Current task assessment with worker input; stop if material change is unassessed.
Provide safe work Take defective equipment out, separate people and vehicles, define a safe loading method. Visible controls and defect closure; no use of an unsafe tail-lift.
Inform and train Show the actual method, limits, reporting and emergency response. Practical demonstration and authorisation for the task.
Check and review Sample actual work, listen to reports and act on near misses. Inspection, supervision and completed corrective actions.

Small-employer and no-charge decisions

GB: a written policy is required where five or more people are employed; employees cannot be charged for provision required by relevant statutory safety requirements (HSWA section 9). NI: use the separate 1978 Order and HSENI: health and safety policy for the corresponding written-policy and no-charge route. The smaller-employer writing exception does not remove substantive duties. HSWA 1974: general duties.

What does so far as reasonably practicable mean?

The duty calls for measures unless the sacrifice needed to reduce the risk is grossly disproportionate to the benefit. It does not mean choosing the cheapest control or waiting for an injury.

Start with the magnitude of harm and established good practice, then examine feasible control options and any genuine difficulty. Record a significant contested decision with evidence and a competent reviewer; uncertainty about a serious risk weighs toward protection. A broken tail-lift should not remain in use while a cost argument is drafted. HSE HSG65 Managing for health and safety.

Apply the qualification to the right duty

The wording of the particular duty governs. The general “so far as is reasonably practicable” qualification is not a cost defence against every requirement: some duties are absolute or use a different qualification. Identify the actual provision before deciding how it is met.

What must workers do, and what remains the employer’s duty?

Workers must take reasonable care for themselves and others, cooperate with the employer’s lawful arrangements and avoid interfering with protective measures. Employers must supply the safe system and act on reported defects.

Employer and employee duties connect

Employer and employee duties connect. Employer: provide and maintain protection: The employer assesses risk, provides safe systems, equipment, information, training, competent help and suitable arrangements. Asking workers to take care does not transfer that duty. Employee: act within the safe system: Employees take reasonable care, cooperate and use controls properly. They report danger and defects through the appropriate arrangements. Other people and controllers: Contractors, agency arrangements, shared premises and visitors require a fact-specific map of control and duties. Ordinary-language worker is not a substitute for legal status.
Learning point: Show that the employer designs, resources and verifies the system while employees take reasonable care, cooperate, use controls correctly and report problems. The relevant source scope and actual work conditions govern application.
Read the complete visual as text
  1. Employer: provide and maintain protection: The employer assesses risk, provides safe systems, equipment, information, training, competent help and suitable arrangements. Asking workers to take care does not transfer that duty.
  2. Employee: act within the safe system: Employees take reasonable care, cooperate and use controls properly. They report danger and defects through the appropriate arrangements.
  3. Other people and controllers: Contractors, agency arrangements, shared premises and visitors require a fact-specific map of control and duties. Ordinary-language worker is not a substitute for legal status.

Consult while the decision can change

Consult while the decision can change. Explain the proposed change: Give workers timely relevant information about risk, options and effects. Use the lawful union-appointed or direct/elected representative route that applies. Listen and revise: Consultation is two-way. Ask about the real task and foreseeable difficulty while choices remain open; identify and respond to concerns. Explain and verify: Explain the decision and required controls, check actual use and feed findings back. A meeting or representative signature does not discharge the employer’s duty.
Learning point: Show consultation happening early enough to influence a decision and closing the feedback loop. The relevant source scope and actual work conditions govern application.
Read the complete visual as text
  1. Explain the proposed change: Give workers timely relevant information about risk, options and effects. Use the lawful union-appointed or direct/elected representative route that applies.
  2. Listen and revise: Consultation is two-way. Ask about the real task and foreseeable difficulty while choices remain open; identify and respond to concerns.
  3. Explain and verify: Explain the decision and required controls, check actual use and feed findings back. A meeting or representative signature does not discharge the employer’s duty.

An operator should use the specified route and controls, stop when a tail-lift behaves abnormally, keep others clear and tell the supervisor. They should not improvise repair or accept pressure to work around a failed device. The supervisor must protect the report, arrange a competent assessment and provide a safe alternative or hold work. HSE employee health and safety duties and HSENI employees.

Distinguish the employee and no-person duties

In GB, section 7 concerns employees’ reasonable care and cooperation; section 8’s prohibition on intentional or reckless interference/misuse applies to any person. Do not treat every employment status as having an identical statutory route. NI uses its separate Order.

How should workers be consulted?

Consultation is a two-way decision process: share proposed changes and risks in time for workers and representatives to influence the control.

Ask those loading, cleaning or repairing equipment how the task actually runs, including peak periods and workarounds. Consult on significant changes, competent-help arrangements, risk information and training; feed back what changed or why. The GB union and non-union routes are explained in HSE L146 Consulting workers on health and safety. NI has its own consultation framework; HSENI consultation with employees guidance covers the non-union employee route. Check the applicable representation arrangements for the workplace.

When is competent assistance needed?

An employer needs suitable competent help to manage duties and must give that person enough information, access and authority to advise effectively.

The level of competence depends on the decision. A supervisor may assess a familiar loading task, while a tail-lift defect, machine alteration or complex exposure needs a suitably skilled specialist. A certificate alone is not proof of competence for the actual equipment and scope. The employer should test advice against site evidence and retain the decision owner. HSE consultation and competent help and HSENI making health and safety work for your business.

How can the hierarchy of controls guide practical precautions under employer and worker duties?

Choose controls that prevent the harm the duty is intended to avoid. In a loading yard, redesign pedestrian and vehicle movement before depending on hi-vis clothing, warnings or a worker noticing a reversing lorry.

Illustrative decision: BuildOut has deliveries crossing the route between its stores and office. The manager, yard supervisor, drivers and workers assess the actual traffic and loading tasks together. A safe solution must work for normal arrivals, a delayed vehicle, contractors and a failed loading bay.

ERICPD means Eliminate, Reduce (including substitution), Isolate, Control, PPE and Discipline. The five-level hierarchy groups measures as elimination, substitution, engineering controls, administrative controls and PPE. They overlap: isolation is usually an engineering measure; control can include engineered and administrative measures. Discipline means maintaining and checking the controls, supervising the method and learning from defects, rather than blaming someone or accepting weaker protection.

The comparison is an original illustrative application of the general HSE hierarchy, not a machine-specific method, permit or design approval. The employer must choose measures for the actual work and jurisdiction. Apply the separate Northern Ireland legal route where relevant; the local assessment and competent technical decision govern release.

How do employer and worker duties apply to unsafe loading?

At BuildOut, the worker’s report starts a hold. Employer duties require safe equipment and a workable alternative; the manager must verify repair and route control before loading resumes.

Serious or immediate danger

2 linked parts. Follow the question numbers and complete the applicable route.

Part 1 of 2 · Questions 1–3

Serious or immediate danger. 5 numbered checkpoints with explicit destinations, uncertainty, responsible roles and controlled rechecks. The full reading text follows the visual.
Continue · Part 2 of 2 · Questions 4–5Serious or immediate danger. 5 numbered checkpoints with explicit destinations, uncertainty, responsible roles and controlled rechecks. The full reading text follows the visual.
Learning point: Serious or immediate danger. Follow 5 source-backed checkpoints and their labelled outcomes; the named role resolves holds before the stated recheck.
Read the complete visual as text
  1. Start: A worker finds a missing critical control, acute release, unsafe equipment or another condition that may create serious and immediate danger.
  2. Question 1: Is anyone injured, trapped or in immediate life danger? Decision owner: Employer or controlling manager with competent task/legal advice.
  3. YES — EMERGENCY: Raise the alarm, call 999, use the safe emergency procedure and avoid improvised rescue. Remain in the emergency route until competent help controls danger. Owner: Employer or controlling manager with competent task/legal advice. STOP / REFER → APPROPRIATE RESPONSE.
  4. NO: Continue the remaining checks; this does not release the task. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 2.
  5. UNKNOWN — PROTECT FIRST: Raise the alarm, call 999, use the safe emergency procedure and avoid improvised rescue. Remain in the emergency route until competent help controls danger. Owner: Employer or controlling manager with competent task/legal advice. STOP / REFER → APPROPRIATE RESPONSE.
  6. Question 2: Can the activity stop or the person withdraw without increasing danger? Decision owner: Employer or controlling manager with competent task/legal advice.
  7. YES: Stop/withdraw, warn others and prevent unauthorised restart or entry. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 3.
  8. NO / UNKNOWN — HOLD: Keep clear and use the site emergency route. Obtain competent emergency or specialist help without unsafe intervention. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.
  9. Question 3: Has the responsible owner controlled the physical danger? Decision owner: Employer or controlling manager with competent task/legal advice.
  10. YES: Check whether serious risk or concern remains. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 4.
  11. NO / UNKNOWN: Keep work held; escalate internally and use representative support where available, then assess the concern route. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 4.
  12. Question 4: Is serious risk unresolved or the internal route unavailable? Decision owner: Employer or controlling manager with competent task/legal advice.
  13. YES / UNKNOWN: Keep work held. Check HSE/local authority in GB or HSENI/district council in NI; do not wait for a regulator before protecting people. Competent correction must precede restart verification. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 5.
  14. NO: Continue the independent competent restart check. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 5.
  15. Question 5: Has a competent check confirmed protection and the authorised owner released work? Decision owner: Employer or controlling manager with competent task/legal advice.
  16. YES: Brief people, record the decision and monitor the restored protection. Owner: Employer or controlling manager with competent task/legal advice. OUTCOME → RECORD AND HAND OVER.
  17. NO / UNKNOWN — HOLD: Do not restart. Resolve the physical control, evidence or authority gap. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 5 AFTER CORRECTION.
  18. Outcome: Emergency response; safe stop or withdrawal; internal escalation; regulator concern; work held; controlled restart.
  19. Stop and escalation boundary: This learning route supplies no design value, operating setting, clinical diagnosis or site permission. The actual procedure, jurisdiction and competent local authority govern.

Does a change require reassessment and consultation

Does a change require reassessment and consultation. 4 numbered checkpoints with explicit destinations, uncertainty, responsible roles and controlled rechecks. The full reading text follows the visual.
Learning point: Does a change require reassessment and consultation. Follow 4 source-backed checkpoints and their labelled outcomes; the named role resolves holds before the stated recheck.
Read the complete visual as text
  1. Start: Equipment, substance, process, speed, layout, staffing, organisation, technology, contractor, workplace or evidence changes.
  2. Question 1: Could the change alter hazard, exposure, people, interface, emergency or control performance? Decision owner: Employer or controlling manager with competent task/legal advice.
  3. YES / UNKNOWN: Hold implementation while the risk and arrangements are reviewed. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 2.
  4. NO: Record why no material effect is expected; still check consultation. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 2.
  5. Question 2: Does it substantially affect health/safety, competent help, information, training or technology? Decision owner: Employer or controlling manager with competent task/legal advice.
  6. YES: Consult in good time through the applicable lawful route while options can change. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 3.
  7. NO: Record why that consultation duty is not triggered. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 3.
  8. UNKNOWN — HOLD: Obtain competent advice before deciding the consultation requirement. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.
  9. Question 3: Are design, resources, competence, emergency and contractor interfaces resolved? Decision owner: Employer or controlling manager with competent task/legal advice.
  10. YES: The named evidence is confirmed. Continue the next applicable check. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 4.
  11. NO / UNKNOWN — HOLD: Do not commission or begin routine work until the responsible owners resolve the interfaces. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.
  12. Question 4: Has the changed control been tested representatively with worker feedback? Decision owner: Employer or controlling manager with competent task/legal advice.
  13. YES: Update instructions, training, records, maintenance and monitoring; explain the decision and approve only the verified state. Owner: Employer or controlling manager with competent task/legal advice. OUTCOME → RECORD AND HAND OVER.
  14. NO / UNKNOWN — HOLD: Redesign or obtain competent approval for a safe controlled trial; do not expose people to uncontrolled danger. Full release remains held. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 4 AFTER CORRECTION.
  15. Outcome: No material effect monitored; reassessment; consultation; design hold; controlled trial; approved operation.
  16. Stop and escalation boundary: This learning route supplies no design value, operating setting, clinical diagnosis or site permission. The actual procedure, jurisdiction and competent local authority govern.

BuildOut loading decision

Task material and setting: At BuildOut Ltd, a warehouse team loads heavy cages into a delivery vehicle. The tail-lift judders and a pedestrian route crosses the loading area.

People and prerequisites: Operators, driver, supervisor, nearby pickers and visitors could be struck, trapped or injured by falling cages. The team needs the lift identity, load limits, instructions and traffic plan.

Before: The operator stops, keeps people clear and reports the fault. The supervisor marks the lift out of use, checks the route and chooses a safe alternative or pauses loading.

During: No one bypasses the defect. A competent maintainer assesses and repairs the lift under the approved safe method, with vehicle movement and energy controlled.

Hold or stop: Hold for uncertain lift condition, missing separation, untrained personnel or an unsafe substitute method. Do not treat a worker’s willingness as a control.

Completion and hand back: The repaired lift is checked against its specified function; the route is restored, staff are briefed and the responsible manager records the return-to-use decision.

Evidence: Keep the defect, assessment, repair/test record, alternative-plan decision, worker consultation and supervisor release.

Do these duties change by sector?

The general duty structure applies across workplaces, but the credible harm and specialist rules vary with the activity.

General duties applied to different settings
Setting Main harm route Practical duty decision
Manufacturing Unguarded cutter or unexpected restart exposes an operator during a jam. Hold use, restrict access and arrange competent safeguarding, isolation and function checks before named release. Sources: HSE risk assessment steps; HSE legislation on leading health and safety.
Construction Loading vehicle crosses a pedestrian route while a contractor lifts materials. Separate the route, coordinate contractor and employer duties, and stop loading if separation or lift control fails. Sources: HSE workplace transport; HSE risk assessment steps.
Hospitality Powered slicer cleaning exposes a worker to a blade; wet floor creates a slip route. Assess normal use and cleaning, train the worker and withdraw the slicer if guarding or the cleaning method is unsafe. Sources: HSE risk assessment steps; HSE Catering frequently asked questions.
Office or service Workstation discomfort, stress or lone work changes with a new service schedule. Consult staff, assess health as well as injury, adjust the task and review reports after the change. Sources: HSE risk assessment steps; HSE consultation and competent help.

Who does what in the organisation?

The employer owns the system, leaders resource it, supervisors verify work, workers follow and challenge controls, and competent advisers support decisions within defined scope.

Who holds the duty and controls the decision

2 linked parts. Follow the question numbers and complete the applicable route.

Part 1 of 2 · Questions 1–3

Who holds the duty and controls the decision. 5 numbered checkpoints with explicit destinations, uncertainty, responsible roles and controlled rechecks. The full reading text follows the visual.
Continue · Part 2 of 2 · Questions 4–5Who holds the duty and controls the decision. 5 numbered checkpoints with explicit destinations, uncertainty, responsible roles and controlled rechecks. The full reading text follows the visual.
Learning point: Who holds the duty and controls the decision. Follow 5 source-backed checkpoints and their labelled outcomes; the named role resolves holds before the stated recheck.
Read the complete visual as text
  1. Start: A work activity, hazard, concern or change needs a named duty and action owner. Injury or immediate danger invokes the appropriate emergency response first; never wait for the status scan.
  2. Question 1: Is the territory known? Decision owner: Employer or controlling manager with competent task/legal advice.
  3. GB: Use the GB general and applicable specialist duties. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 2.
  4. NORTHERN IRELAND: Use the separate NI duties and regulator route. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 2.
  5. UNKNOWN — HOLD: Confirm the work location before a legal conclusion. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 1 AFTER CORRECTION.
  6. Question 2: Is the person’s actual status sufficiently established for this decision? Decision owner: Employer or controlling manager with competent task/legal advice.
  7. YES: Record employee, self-employed, agency/temporary, contractor, visitor or other affected status as appropriate. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 3.
  8. NO / UNKNOWN — HOLD: Obtain fact-specific advice; do not rely only on a tax or contract label. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 2 AFTER CORRECTION.
  9. Question 3: Who controls employment, premises, equipment, method, timing and interfaces? Decision owner: Employer or controlling manager with competent task/legal advice.
  10. ONE CONTROLLER: Name that control and its owner. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 4.
  11. SEVERAL CONTROLLERS: Map each dutyholder and coordinate information and controls. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 4.
  12. UNKNOWN — HOLD: Hold the unsafe activity until control and authority are clarified. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 3 AFTER CORRECTION.
  13. Question 4: Does specialist law add another role? Decision owner: Employer or controlling manager with competent task/legal advice.
  14. YES: Add the applicable designer, client, principal, appointed, competent or responsible-person role without removing general duties. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 5.
  15. NO: Record the scope check. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 5.
  16. UNKNOWN — HOLD: Get competent advice on the affected role before the decision continues. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 4 AFTER CORRECTION.
  17. Question 5: Does the owner have authority, competence, capacity and escalation? Decision owner: Employer or controlling manager with competent task/legal advice.
  18. YES: Implement and communicate the control; verify it and release only within the named authority. Owner: Employer or controlling manager with competent task/legal advice. OUTCOME → RECORD AND HAND OVER.
  19. NO / UNKNOWN — HOLD: Hold and escalate to the person who can resource and control the risk. Owner: Employer or controlling manager with competent task/legal advice. HOLD → REPEAT QUESTION 5 AFTER CORRECTION.
  20. Outcome: Territory confirmed; status reviewed; overlapping control mapped; specialist role added; activity held; control owned and verified.
  21. Stop and escalation boundary: This learning route supplies no design value, operating setting, clinical diagnosis or site permission. The actual procedure, jurisdiction and competent local authority govern.

A supplier, designer, premises controller or contractor may have additional duties relevant to their role. Map who controls the hazard and information at each interface; a contract does not automatically remove the host employer’s duties. A safety adviser cannot make an unsafe loading method safe by signing a form. Health and Safety at Work etc. Act 1974 and Health and Safety at Work (Northern Ireland) Order 1978.

What competence does each role need?

Teach the decision each role actually makes, assess it in the real work and review authority after change or poor performance.

From legal duty to verified control

From legal duty to verified control. Define the work and law: Identify the real task, people, territorial route and any sector-specific role. The GB and Northern Ireland general-duty frameworks are separate. Resource a physical control: Risk assessment must lead to an owned, resourced control that breaks the harm path. A document, PPE issue or training attendance alone is not evidence of effectiveness. Verify and review: Observe the control in the actual conditions, explain worker actions and retain evidence. A defect, change, new information or incident can require reassessment.
Learning point: Turn abstract general duties into an operational chain that can be checked at the point of work. The relevant source scope and actual work conditions govern application.
Read the complete visual as text
  1. Define the work and law: Identify the real task, people, territorial route and any sector-specific role. The GB and Northern Ireland general-duty frameworks are separate.
  2. Resource a physical control: Risk assessment must lead to an owned, resourced control that breaks the harm path. A document, PPE issue or training attendance alone is not evidence of effectiveness.
  3. Verify and review: Observe the control in the actual conditions, explain worker actions and retain evidence. A defect, change, new information or incident can require reassessment.

Concern reporting and regulator route

2 linked parts. Follow the question numbers and complete the applicable route.

Part 1 of 2 · Questions 1–3

Concern reporting and regulator route. 5 numbered checkpoints with explicit destinations, uncertainty, responsible roles and controlled rechecks. The full reading text follows the visual.
Continue · Part 2 of 2 · Questions 4–5Concern reporting and regulator route. 5 numbered checkpoints with explicit destinations, uncertainty, responsible roles and controlled rechecks. The full reading text follows the visual.
Learning point: Concern reporting and regulator route. Follow 5 source-backed checkpoints and their labelled outcomes; the named role resolves holds before the stated recheck.
Read the complete visual as text
  1. Start: A worker, representative, contractor or member of the public identifies an unsafe or unhealthy work activity.
  2. Question 1: Is there serious or immediate danger? Decision owner: Employer or controlling manager with competent task/legal advice.
  3. YES / UNKNOWN DANGER: Use the emergency, stop or safe-withdrawal route first and call 999 where needed. Continue reporting only when safe. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 2.
  4. NO: Continue safe concern reporting. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 2.
  5. Question 2: Can the concern be raised promptly with the controlling person? Decision owner: Employer or controlling manager with competent task/legal advice.
  6. YES: Report task, hazard, people exposed, missing control and action; keep a factual record. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 3.
  7. NO / UNKNOWN / UNSAFE ROUTE: Seek safe representative or external support without delaying urgent protection. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 3.
  8. Question 3: Is a representative or union route available? Decision owner: Employer or controlling manager with competent task/legal advice.
  9. YES: Use that support without delaying urgent action. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 4.
  10. NO: Proceed to the response check. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 4.
  11. UNKNOWN: Check availability where safe and useful; proceed to assess the response. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 4.
  12. Question 4: Is the concern controlled and response explained? Decision owner: Employer or controlling manager with competent task/legal advice.
  13. YES: Record control and feedback. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 5.
  14. NO / UNKNOWN: Confirm territory and activity; use HSE/local authority in GB or HSENI/district council in NI. Keep serious-risk work held; no regulator outcome is promised. Owner: Employer or controlling manager with competent task/legal advice. CONTINUE → QUESTION 5.
  15. Question 5: Could detriment, dismissal or protected disclosure be an issue? Decision owner: Employer or controlling manager with competent task/legal advice.
  16. YES / UNCERTAIN: Seek timely territory-specific union or employment-law advice; GB and NI advice routes differ. Owner: Employer or controlling manager with competent task/legal advice. STOP / REFER → APPROPRIATE RESPONSE.
  17. NO: Close feedback and keep controls under review. Neither route guarantees legal protection. Owner: Employer or controlling manager with competent task/legal advice. OUTCOME → RECORD AND HAND OVER.
  18. Outcome: Emergency controlled; internal action; representative escalation; regulator concern; employment advice; feedback closed.
  19. Stop and escalation boundary: This learning route supplies no design value, operating setting, clinical diagnosis or site permission. The actual procedure, jurisdiction and competent local authority govern.
Role learning demonstration assessment and reassessment
Role What to learn Practical proof Assessor and record Reassessment trigger
New worker Learn site hazards, reporting, consultation and emergency alarm; no specialist authority. Can identify a defective lift and explain the stop route. Supervisor records induction scope. New site, task or near miss.
Task operator Learn real equipment, load, route, stop conditions and safe method. Demonstrates safe loading and defect response. Authorised supervisor records task sign-off. Changed equipment, load or observed drift.
Supervisor Translate assessment into briefing, hold decisions, alternatives and handback. Runs the tail-lift scenario and documents hold and release. Manager samples and signs decisions. Repeated defect or changed operation.
Manager or director Resource controls, competent help, consultation and review. Explains risk priorities, action closure and challenged evidence. Responsible leader/board reviews records. New business, serious event or assurance failure.
Safety/technical adviser Know jurisdiction, specialist boundaries and evidence quality. Traces a duty through controls and field performance. Independent competent reviewer. Law, equipment or major risk change.

Which GB and NI legal routes apply?

Use the law for the workplace jurisdiction. GB HSWA 1974 and Management Regulations 1999 are distinct from the NI 1978 Order and NI Management Regulations 2000.

Specific work may also engage equipment, hazardous-substance, construction, fire or reporting law. This page teaches the general framework; identify the actual activity before attaching an additional legal requirement. The table separates the primary routes and consultation. HSE health and safety law basics and HSENI making health and safety work for your business.

What evidence shows duties are working?

A good record points to a real control that workers can see and use; it also shows who acted when the control failed.

Sample task assessments, worker consultation, competence demonstrations, defect and near-miss reports, maintenance closure, supervision, emergency practice and action follow-up. Compare records with a field walk. A policy signed by a director is useful only if it drives resources and decisions. HSE legislation on leading health and safety and HSE risk assessment steps.

When should work stop or escalate?

Stop when a control is missing, equipment is unsafe, the route is blocked, an exposure is uncontrolled or the task has changed beyond the assessment.

Keep clear, report through the site route, protect others and seek a safe alternative. For imminent danger or injury, use the emergency plan and call appropriate help. Supervisors must not restart until the hazard, competence and control evidence support it. Repeated workarounds are a system signal that needs management action. HSE employee health and safety duties and HSENI employees.

What do the acronyms and key terms mean?

These definitions keep GB and NI law, guidance and local controls distinct.

Definitions are grounded in Health and Safety at Work etc. Act 1974.

General-duty terms
Term Full name Meaning here
HSWA Health and Safety at Work etc. Act 1974 GB general health and safety statute.
NI Order Health and Safety at Work (Northern Ireland) Order 1978 Separate NI general statute.
MHSWR Management of Health and Safety at Work Regulations GB 1999 and NI 2000 are separate instruments.
ACOP Approved Code of Practice Guidance with a distinct legal status from ordinary guidance.
SFARP So far as reasonably practicable Legal test for proportionate risk reduction.
PPE Personal protective equipment Residual protection after stronger controls.
ERICPD Eliminate, Reduce, Isolate, Control, PPE, Discipline Professional planning aid for control choices.
Competent person Not an acronym Person with suitable knowledge, experience and qualities for the assigned help.