SHARE Knowledge Hub
Work Equipment, Lifting Equipment and Pressure Systems
A machine, lifting device or pressure system may have overlapping duties, but a single certificate does not close every risk. Identify the actual task and equipment, apply the workplace-use rules, then test whether lifting or qualifying pressure-system duties add planning, examination, written-scheme and competent-person requirements. Stop a lift or pressurised operation when the safe limits, critical condition or examination status cannot be demonstrated.
Understanding Work Equipment, Lifting Equipment and Pressure Systems
A machine, lifting device or pressure system may have overlapping duties, but a single certificate does not close every risk. Identify the actual task and equipment, apply the workplace-use rules, then test whether lifting or qualifying pressure-system duties add planning, examination, written-scheme and competent-person requirements. Stop a lift or pressurised operation when the safe limits, critical condition or examination status cannot be demonstrated.
Why this matters at work
Identify and safely verify the controls whose failure could cause serious harm, using suitable competence and task-specific evidence. Observation, inspection and maintenance complement one another; a checklist or past report does not approve current physical condition.
Inspect reports for defects and required actions and ensure the equipment remains suitable between examinations through maintenance and appropriate checks. A thorough examination does not automatically require an overload test; testing should be determined by competent assessment because unnecessary tests can damage equipment. Keep evidence available where equipment moves or is hired. Arrange prompt competent advice after damage, modification or unusual loading and remove equipment from use when required. Do not treat a recent report as permission for a different lifting duty, people lifting or an attachment outside the assessed configuration.
How organisations manage this in practice
Provide appropriate controls to bring equipment to a safe condition in a safe manner. Stop controls should have priority over start controls, and stopping the equipment or relevant parts should remove energy where appropriate. The required stopping function depends on the process: uncontrolled power removal can itself create danger for some brakes, loads or chemical processes.
Identify normal stop, controlled stop, emergency stop and isolation as distinct functions. Confirm that the person can reach the control, that the hazardous motion ceases soon enough, and that associated feed or downstream machinery is coordinated. A stop button does not dissipate residual pressure or prevent gravity movement.
A lift can involve crane owner, hire firm, principal contractor, site occupier, slinger, operator and examiner. Pressure plant can involve owner, installed-system user, maintenance contractor and insurer. Define who plans, inspects, maintains, examines, receives reports, controls defects and tells other employers before work begins.
Controls should be clearly visible, identifiable and appropriately marked, and generally positioned outside danger zones. Control systems must be safe and chosen to avoid danger in reasonably foreseeable failure and use. An operator should know what each control does without ambiguous symbols or accidental activation.
A written scheme, report and maintenance record differ
Several regimes can apply to one asset. A competent examination plan, completed findings and maintenance evidence answer different questions.
Define the system
Identify vessel, connected pipework, protective devices and the actual boundary through the competent pressure-system process.
Written scheme
The applicable scheme defines the scope and requirements for examination; it is not evidence that examination has been completed.
Report and maintenance
An examination report records findings and actions. A maintenance record records work done; neither automatically closes the other’s requirements.
Operating acceptance
The competent owners resolve applicable evidence and restrictions before use. Lifting planning and examination have their own route; no pressure settings, venting steps or intervals are supplied.
Read the complete task-specific control examples
ERICPD is a planning cross-map: Discipline verifies and sustains every control. ESEAP compares effectiveness. A label does not authorise the task; retain the owner, evidence and stop or change decision.
Work Equipment, Lifting Equipment and Pressure Systems · ERICPD
- Eliminate
- Avoid an unnecessary suspended lift or pressure-dependent step by redesigning flow or assembling at a safe accessible position.
- Reduce
- Choose a lifting or process method with suitable capacity and controlled interfaces for the actual load, radius, pressure and substance.
- Isolate
- Provide designed physical safeguards: separation from suspended loads, suitable lifting installation and pressure-system protective devices.
- Control
- Plan and supervise lifting to its complexity and define pressure-system operating limits and required written scheme/examination arrangements.
- PPE
- Select PPE for remaining handling, splash or other task exposure, checking fit and compatibility.
- Discipline
- Maintain equipment and protective devices, complete required examinations and close defects through competent decisions.
Work Equipment, Lifting Equipment and Pressure Systems · ESEAP
- Elimination
- Avoid an unnecessary suspended lift or pressure-dependent step by redesigning flow or assembling at a safe accessible position.
- Substitution
- Choose a lifting or process method with suitable capacity and controlled interfaces for the actual load, radius, pressure and substance.
- Engineering controls
- Provide designed physical safeguards: separation from suspended loads, suitable lifting installation and pressure-system protective devices.
- Administrative controls
- Plan and supervise lifting to its complexity and define pressure-system operating limits and required written scheme/examination arrangements.
- PPE
- Select PPE for remaining handling, splash or other task exposure, checking fit and compatibility.

Mobile cranes: follow the load, support and people through a lift
Explore how this equipment can harm its users and other people, then follow the practical measures that interrupt each pathway. This is a hazards and good-practice lesson; the separate checklist remains the pre-use/safety-check activity.
Hazards and good practice: learn what can hurt people during use, change and maintenance. Pre-use and safety checks stay in the separate checklist.
Checksheets and risk assessments
Equipment checksheets
- Mobile cranes and planned lifts — 3D checks · Word · PDF
- Lifting accessories — 3D checks · Word · PDF
Risk assessment forms
Risk assessment examples
Forms and tools
Full written walkthrough — all 8 steps
1. Start with the complete lifting operation
What is happening: The crane, supporting ground, load, route and people form one operation.
How harm can occur: A technically sound crane can still overturn or drop a load in an unsuitable plan.
Best practice to apply: Resource and plan the actual lift through a person with competence proportionate to its complexity and risk.
Why this works: Planning joins equipment selection to the real task instead of treating examination as approval to lift anything.
Load-Handling Equipment and Lifting Operations · What does load-handling equipment and lifting operations mean?2. Establish the real load and configuration
What is happening: The load includes relevant attachments and accessories, not only the labelled object.
How harm can occur: An incorrect mass, centre of gravity or configuration can overload equipment or destabilise the lift.
Best practice to apply: Establish load information and use the actual crane/attachment data and planned configuration; the model supplies no capacity.
Why this works: Correct input data is needed before the equipment's limits can be applied.
Load-Handling Equipment and Lifting Operations · How should a motor lift change when the load is not as expected?3. Trace reactions into the ground
What is happening: Outriggers and spreaders transmit reactions into the supporting surface or structure.
How harm can occur: A void, inadequate support or movement can cause overturn and crush people.
Best practice to apply: Obtain suitable ground/support information and competent design of the set-up and spreading arrangements.
Why this works: Load-spreading and support must be based on reactions and capacity, not how firm the ground feels.
Load-Handling Equipment and Lifting Operations · What technical lifting details should learners understand?4. Connect the load with suitable accessories
What is happening: Hooks, slings and connections form the load path between the crane and the item.
How harm can occur: Failure, unsuitable sling angles or an unstable attachment can drop or shift the load.
Best practice to apply: Use accessories suitable for the load, arrangement and actual duties, with competent selection and required condition/examination controls.
Why this works: Every link has to suit the task; a marked component does not validate the complete arrangement.
Load-Handling Equipment and Lifting Operations · Documents to download5. Keep people out of the load and machine routes
What is happening: The load route, slewing equipment and landing area create different danger interfaces.
How harm can occur: A moving or falling load can strike or crush a person, including someone guiding or receiving it.
Best practice to apply: Plan separation, a controlled landing area and safe positions; avoid lifting over people and protect other operations.
Why this works: The safest contact with the load path is often no contact at all.
Load-Handling Equipment and Lifting Operations · Load-Handling Equipment and Lifting Operations FAQs - what do people ask?6. Coordinate signals and visibility
What is happening: The operator may not see the full load or landing interface.
How harm can occur: Lost signals or conflicting instructions can create unintended movement towards people or obstructions.
Best practice to apply: Agree the communication and responsible roles; stop when essential visibility or communication is lost.
Why this works: An agreed single control arrangement prevents incompatible instructions during a critical movement.
Load-Handling Equipment and Lifting Operations · What should stop a lifting operation?7. Keep the plan valid as conditions change
What is happening: Radius, load condition, weather and nearby work may change during the operation.
How harm can occur: A changed configuration or new obstruction can invalidate the planned controls.
Best practice to apply: Stay within the actual plan and manufacturer limits; pause and re-plan a material change rather than improvise.
Why this works: The plan applies to its stated conditions, not every variation that occurs later.
Load-Handling Equipment and Lifting Operations · What technical lifting details should learners understand?8. Separate lifting from maintenance and hand-back
What is happening: A crane at rest may still contain hydraulic, gravitational and other stored energy.
How harm can occur: Unexpected descent or release can injure a fitter or someone handling equipment.
Best practice to apply: Use competent machine-specific isolation/support and defect arrangements; verify readiness before the next lifting task.
Why this works: A stopped lift does not establish a safe maintenance condition or approve the next operation.
Load-Handling Equipment and Lifting Operations · What checks, inspections and examinations are needed?
Illustrative awareness learning. Geometry, colours and movement do not establish safe distances, capacity, exposure, isolation or work permission. Use the actual assessment, equipment information and competent arrangements.
The wider workplace has its own account and subscription access. Exploring this lesson does not grant access, record course completion or authorise work.
UK guidance for further reading
HSE: Mobile cranesHow can I practise this topic in 3D?

Incorrect support on the two-post lift

A long load is lifted without a suitable plan

Utilities case: steam maintenance still needs energy control
All related inspection points 11 across 6 locations
Garage workshop 2 inspection points
Construction site 1 inspection point
Crown Fuels terminal 1 inspection point
Warehouse walkabout 4 inspection points
From flour to chilled despatch 1 inspection point
Aerosystems Engineering 2 inspection points
Practice in the SHAREhub environment. Browser practice is separate from workplace competence and formal learning records.
What should a worker do before using work equipment?
Confirm the equipment is the right type for the task, check guards and controls, inspect for obvious damage, understand the safe method and emergency response, keep others clear, and stop if condition or permission is uncertain.
Do not begin because the equipment ran yesterday, carries a conformity mark or belongs to a contractor. Check any recorded limitation, attachment, inspection status and local authorisation that the task actually requires.
Identify equipment and task. During use: Use within assessed conditions.; At completion: Stop safely and leave controlled.
Check guards, controls and condition. During use: Watch for change or defect.; At completion: Report defects and hand back.
Confirm competence and area. During use: Keep others protected.; At completion: Record any hold or release.
What counts as work equipment and use?
Work equipment includes machinery, appliances, apparatus, tools and installations used at work, while use includes starting, stopping, programming, setting, transporting, repairing, modifying, maintaining, servicing and cleaning.
A hand tool, office appliance, machine line, scaffold component, ladder, lift truck or process installation may be work equipment. The applicable controls depend on the actual use and risk, not the label or purchase value.
Tool or appliance. Why it is in scope: Used to perform work.; Decision: Suitability and safe use.
Machine or installation. Why it is in scope: Creates mechanical or other energy hazards.; Decision: Guarding, controls and lifecycle evidence.
Cleaning or adjustment. Why it is in scope: It is use under Provision and Use of Work Equipment Regulations (PUWER).; Decision: Safe state and competent method.
Transport or modification. Why it is in scope: Can change condition or risk.; Decision: Planning, inspection and change control.
How do workplace-use duties differ from product-supply duties?
PUWER controls equipment provided or used at work; product-supply rules govern placing products on a market. A CE, UK Conformity Assessed (UKCA) or CE and UK Northern Ireland (UKNI) route does not by itself prove workplace suitability, correct installation or safe use.
Choose the GB or NI market route and the product sector before relying on conformity documentation. Separately complete workplace selection, risk assessment, guarding, installation, competence, inspection and maintenance decisions.
Who will use it and for what? Workplace-use route: PUWER and other workplace law.; Product-supply route: Not the main market decision.
May this product be placed on this market? Workplace-use route: Does not answer safe-use question.; Product-supply route: Current GB or NI sector rules.
Was it modified or assembled? Workplace-use route: Reassess safe use.; Product-supply route: May create manufacturer obligations.
How can lifting or pressure failures harm people?
A failed sling or unstable lift can drop or swing a load into people; loss of containment can release hot, toxic or high-energy fluid. A shared piece of equipment can need separate safeguards and examinations for each failure pathway.
Identify load path, lifting configuration, pressure source, safe limits, people exposed and the independent barriers. Hold the operation when a critical examination, written scheme or safe state is uncertain.
| Initiating event | Possible harm | Control and hold point |
|---|---|---|
| Load or attachment exceeds rated configuration | Collapse or dropped load can crush people below. | Use a planned lift, marked safe working load and verified configuration; stop when rating or ground is uncertain. |
| Defective lifting accessory | A sling or hook fails and the load swings or falls. | Pre-use check plus competent thorough examination; withdraw a dangerous defect. |
| Pressure system exceeds safe limit | Rupture or release causes blast, scald or toxic exposure. | Defined safe limits, protective devices and written-scheme examination; isolate on abnormal pressure. |
How do PUWER, LOLER and pressure-system law fit together?
Use PUWER for the general safe-use duties of work equipment; add Lifting Operations and Lifting Equipment Regulations (LOLER) when the activity and equipment are within lifting law, and add Pressure Systems Safety Regulations (PSSR) where the pressure-system definition and application provisions are met. One asset can trigger more than one regime.
Do not infer that every pressure vessel needs a written scheme or that every vertical movement is LOLER lifting. Decide jurisdiction, equipment identity, use, relevant fluid, load and exceptions with competent evidence before choosing the route. Product-supply law is a separate question.
| Question | Route | Evidence |
|---|---|---|
| Is equipment used at work? | GB or NI PUWER baseline. | Task and equipment assessment. |
| Does it lift or lower a load? | GB or NI LOLER applicability review. | Lift plan, marking and examination evidence. |
| Does it meet pressure-system scope? | GB PSSR 2000 or NI PSSR 2004 applicability review. | System boundary, fluid, limits and written scheme decision. |
| Is it being placed on a market? | Current sector product-supply law. | Conformity evidence, separate from workplace acceptance. |
How can the hierarchy of controls reduce equipment, lifting and pressure-system risks?
Remove the hazard where reasonably practicable. If it remains, consider a safer method, engineering controls and safe work arrangements before personal protective equipment for residual risk.
HSE places elimination, substitution, engineering, administrative controls and personal protective equipment in that order. Verify that the chosen controls work on the actual task.
ERICPD (Eliminate, Reduce including substitution, Isolate, Control, personal protective equipment (PPE), Discipline) is a SHARE decision prompt cross-mapped to HSE’s five-level hierarchy. Choose stronger feasible controls first, verify them in the actual task and record why a stronger option cannot be used. Discipline means sustaining controls through maintenance, supervision and learning.
What makes an activity a lifting operation?
A lifting operation is concerned with lifting or lowering a load, including a person; determine whether the equipment and activity fall under the applicable GB or NI LOLER regime before using a lifting checklist. A mobile elevating work platform (MEWP) is one example whose actual lifting function and use need a competent scope decision.
Conveyors, escalators, simple pallet trucks that only raise enough for travel, and public-use equipment can have different routes. A MEWP, hoist, crane, sling, lift truck or lifting attachment needs a task-specific decision. Do not equate any upward motion with LOLER.
Crane or hoist. Question: What load and lift path?; Next step: LOLER and PUWER assessment.
MEWP or people carrier. Question: Are people lifted and what other height duties apply?; Next step: Specialist competent route.
Conveyor or simple pallet truck. Question: Is this lifting within LOLER meaning?; Next step: Verify applicability; PUWER may still apply.
How is lifting equipment selected and rated?
Select equipment and accessories for the actual load, configuration, environment and failure modes; check marked safe working load and applicable configuration information before the lift.
Capacity alone is not compatibility. Check the load mass and centre of gravity, attachment method, travel path, support and ground, foreseeable dynamic effects, people nearby and manufacturer limits. A magnet or vacuum attachment needs material and surface compatibility, not merely a matching mass.
| Decision | Evidence | Stop |
|---|---|---|
| Load and attachment | Known mass, shape, balance and compatible device. | Unknown or mismatched load. |
| Strength and stability | Rated configuration, support and siting. | Unverified ground or configuration. |
| Lift path | Clear route, exclusions and communication. | People or obstruction in danger path. |
Who plans and supervises lifting operations?
Every lifting operation involving lifting equipment must be properly planned by a competent person, appropriately supervised and carried out safely, with the depth of the plan proportionate to the foreseeable risk.
Simple repeated work may use a suitable standing plan; unusual, complex or changed lifts need a specific competent review. Set roles, communication, load attachment, travel, exclusion, weather, ground and contingency before starting. A template alone is not a completed plan.
| Stage | Decision | Hold |
|---|---|---|
| Plan | Match equipment, load, people, place and sequence. | Unknown facts or unresolved interface. |
| Brief | Check who directs, operates, attaches and stops. | Conflicting roles or signals. |
| Execute | Monitor load and conditions against plan. | Unexpected movement or changed condition. |
What changes when lifting people?
Lifting people requires equipment and arrangements suitable for that purpose, with additional safeguards, escape and rescue decisions and thorough-examination requirements under the applicable lifting regime.
Do not use a goods-only lifting device to carry people without a lawful and competent equipment-specific route. Confirm carrier, controls, fall and crushing risks, communication, rescue, capacity and the separate work-at-height or care-setting requirements where relevant.
Is the carrier designed for people? Evidence: Manufacturer purpose and marking.; Stop: Goods-only or uncertain.
Can people be protected and rescued? Evidence: Task plan and emergency method.; Stop: Rescue not available.
Is statutory examination current? Evidence: Competent report or scheme.; Stop: Missing or adverse report.
What is checked immediately before a lift?
Before lifting, identify equipment and load, check accessories and attachment, confirm the current plan and applicable examination evidence, inspect for visible defects, clear the route and verify people, ground, signals and stop arrangements.
A pre-use check does not replace thorough examination, nor does an examination report replace the user check. Conditions may change after either record was made.
Identity, markings, visible condition and report. During: Keep within assessed route and configuration.; After: Set down safely and inspect.
Load, attachment, people, ground and signals. During: Stop for drift, alarm or change.; After: Record defects and handover.
How is LOLER thorough examination different from inspection?
A LOLER thorough examination is a competent person's systematic, detailed assessment with a written report under the applicable law or competent examination scheme; a user check, PUWER inspection and maintenance are separate controls.
The applicable law or scheme determines the examination timing and scope. Initial installation, reassembly, deterioration and exceptional events may trigger examination. Do not publish a universal site interval, use an old sticker alone, or treat routine overload testing as automatic. See HSE Thorough examinations and inspections of lifting equipment.
| Activity | Purpose | Who decides |
|---|---|---|
| User check | Spot obvious current defect before use. | Trained user and local method. |
| PUWER inspection | Detect installation or deterioration issues. | Risk assessment and competent inspector. |
| LOLER thorough examination | Statutory safety assessment and report. | Competent examiner and law or scheme. |
| Maintenance | Keep equipment safe and functional. | Equipment owner and competent maintainer. |
What happens when a lifting examination finds a defect?
A dangerous or potentially dangerous finding must be communicated and acted on through the applicable reporting route; withdraw equipment from use as required, control the area and use the competent report to decide repair, re-examination and release.
Do not treat a passed sticker, a maintenance action or production pressure as authority to override the report. The competent examiner and dutyholder have distinct reporting responsibilities; the exact statutory route depends on GB or NI law and the finding.
Dangerous defect. Immediate action: Stop and prevent use.; Evidence: Report, quarantine and notification.
Time-limited defect. Immediate action: Meet the report requirement or stop use.; Evidence: Action owner and deadline.
Repair complete. Immediate action: Obtain required verification before use.; Evidence: Technical evidence and named release.
What must be checked when lifting equipment is hired or moved?
The receiving organisation must verify equipment identity, suitability, condition, instructions and required examination evidence before use, while supplier, hirer and site owners coordinate their distinct duties.
Reassembly at a new site or an exceptional event can trigger further examination. Transfer records should follow the equipment; a delivery note is not a lift plan or proof of safe assembly.
Supplier to hirer. Check: Identity, instructions, condition and reports.; Hold: Missing or mismatched evidence.
Site assembly. Check: Competent installation and examination trigger.; Hold: Unverified assembly.
Site to operator. Check: Task plan, competence, site limits and defects.; Hold: Unbriefed operator or changed site.
Great Britain: choosing the examination route
For GB LOLER, unless a competent examination scheme specifies another interval, the usual periodic categories are six months for equipment lifting people and lifting accessories, and twelve months for other lifting equipment. Initial-use evidence, installation or reassembly and exceptional events need separate checks; a current periodic date does not cancel those triggers. The competent examiner determines the actual scheme and report requirements. Use the separate NI LOLER instrument and HSENI route for NI equipment, rather than transplanting this GB summary.
When does pressure-system law apply?
Determine whether the system, relevant fluid and exclusions fall under GB PSSR 2000 or NI PSSR 2004 before deciding on safe limits, a written scheme and examination.
Steam, compressed gas and some hot-water systems may be within scope, but applicability is not decided by a pressure gauge alone. Hydraulic oil systems can still be dangerous and require PUWER or other controls even when outside PSSR. Map vessel, pipework, pipeline, protective devices and fluid with competent advice.
| Question | Evidence | Do not infer |
|---|---|---|
| What is the relevant fluid? | Fluid and operating conditions. | Every pressurised liquid is PSSR. |
| What is the system boundary? | Vessels, pipework, pipeline and protection. | One label covers every component. |
| Is an exception relevant? | Current GB or NI Schedule and competent review. | An exemption from one duty removes all safety duties. |
Who sets safe operating limits for a pressure system?
The user or owner must have safe operating limits established from competent system-specific evidence and operate within them; the page cannot set a pressure, temperature, flow or relief-device value.
Check every component and protective device, including the weakest boundary, changed duty and repair history. Manufacturer information and competent assessment control the actual limits. Ensure operators can see and act on them.
Limits established. Evidence: Design and manufacturer data plus competent system assessment.; Stop: Unknown or conflicting limit.
Protection suitable. Evidence: Verified device selection, setting and discharge route.; Stop: Defeated or uncertain protection.
Operation within limits. Evidence: Readable indication and response.; Stop: Excursion or unreliable reading.
Great Britain: facts for the pressure-system scope decision
HSE identifies steam at any pressure, compressed or liquefied gas above 0.5 bar gauge, pressurised hot water above 110 °C and gas dissolved under pressure as relevant-fluid categories. These are applicability clues, not operating limits. Map the system and exceptions with the competent person. Under GB PSSR the installed-system user and mobile-system owner have distinct dutyholder routes; hired equipment still needs verified scheme and examination evidence. Apply the separate NI PSSR 2004 route in Northern Ireland.
What is a written scheme of examination?
For a qualifying pressure system, the user or owner must have a suitable written scheme before operation; a competent person draws it up or certifies it, and it identifies covered parts, examination methods, intervals and preparation for safe examination. Before first use of a qualifying system, the written scheme must be in place and the required examination undertaken; keep the system out of use until both are satisfied.
The scheme must cover protective devices and relevant vessels or pipework whose failure could cause danger, subject to the applicable legal text and competent scope decision. It is not a maintenance schedule, a generic certificate or proof that an examination has happened. See HSE L122 Safety of pressure systems.
| Element | Decision | Evidence |
|---|---|---|
| Scope | Which vessels, pipelines, pipework and protective devices? | Identified boundary and exclusions. |
| Method and timing | How and when each part is examined? | Competent-person certified scheme. |
| Preparation | How is examination made safe? | Isolation, access and special measures. |
| Change | Does modified use require revision? | Scheme review and certification. |
How does pressure-system examination work?
The system parts in the written scheme must be examined by a competent person in accordance with that scheme, with reports and actions that show whether continued use is safe.
The competent person needs suitable knowledge, resources, independence and authority for the actual system. Examination does not replace operator checks, maintenance, safe limits, protective devices or correct repair. Do not infer intervals from a generic boiler or compressor example.
| Step | Evidence | Hold |
|---|---|---|
| Before | Current suitable written scheme and safe preparation. | No scheme or unsafe access. |
| Examine | Competent examination to scheme. | Unexamined required part. |
| Report and act | Findings, due dates and danger action. | Unsafe finding not closed. |
How are pressure systems operated and maintained?
Operate within established safe limits using effective protective devices, competent people, clear instructions and a whole-system maintenance plan; isolate and depressurise safely before intervention.
Pressure-system examination and maintenance are different. Include corrosion, leakage, alarms, relief devices, connections, pipework, environment, change and operator handover. A pressure indication of zero at one point is not proof that all stored energy is controlled.
Start and run. Control: Limits, protection and competent operation.; Stop: Unreliable reading or excursion.
Maintain. Control: Isolation, depressurisation, verification and safe access.; Stop: Trapped pressure or unknown connection.
Handover. Control: Condition, defects and outstanding actions.; Stop: Unclear plant state.
What happens after pressure-system repair or modification?
Hold the affected system, assess the change against design and safe limits, update the written scheme when required, obtain competent examination where the scheme or law requires it, and release only after controlled testing and named acceptance.
Repairs, replacement components, changed fluids and operating conditions can alter the pressure boundary. A maintenance completion or leak test alone is not statutory examination or authority to operate.
Repair or replacement. Check: Material, design, protective devices and required examination.; Release condition: Competent evidence accepted.
Changed duty. Check: Safe limits, scheme scope and instructions.; Release condition: Updated and approved basis.
Commissioning test. Check: Controlled plan, exclusions and stop triggers.; Release condition: Documented operating handback.
What should happen after a pressure release or alarm?
Move people clear, raise the alarm, follow the site emergency plan and keep the system isolated from further operation; do not approach a leak, adjust a relief device or reopen a vessel until the hazard and safe state are established by authorised people.
Treat vessel, line and connected process as potentially energised. Investigate cause and affected scope, protect others, obtain any required competent examination and controlled test, then require named operating acceptance.
Leak or unusual sound. Immediate action: Withdraw and warn.; Restart barrier: No approach until assessed.
Relief device operates. Immediate action: Escalate and preserve evidence.; Restart barrier: No reset-only return.
Rupture or injury. Immediate action: Emergency response and exclusion.; Restart barrier: Investigation and competent release.
Can one inspection or certificate cover every duty?
No. Keep a distinct evidence route for PUWER inspection, LOLER thorough examination, pressure written-scheme examination, maintenance, pre-use checks and product conformity; only a competent, lawful decision can determine any overlap.
A contractor or insurer may supply a report, but the dutyholder must verify scope, findings, equipment identity and actions. A clear matrix prevents an in-date document for one duty being mistaken for another.
| Record | What it proves | What it does not prove |
|---|---|---|
| Pre-use check | Current obvious condition. | Statutory examination. |
| PUWER inspection | Relevant installation or deterioration findings. | LOLER or PSSR compliance by itself. |
| LOLER report | Competent lifting examination. | Safe lift plan or maintenance. |
| Pressure written scheme | Examination plan and scope. | Completed examination or repair. |
| Pressure report | Findings to the scheme. | Product conformity or operation within limits. |
| Product declaration | Applicable supply assessment. | Safe workplace use. |
What if lifting equipment and a pressure system interact?
Assess every relevant regime and the shared failure path, such as a pressure-powered lifting device, a pressurised attachment or a lift near a pressure vessel; coordinate the plant owners before work.
A lifting plan cannot certify a pressure boundary, and a pressure written scheme cannot approve a suspended-load route. Map energy, load, people, structures and simultaneous work, then hold until each competent decision and handover is complete.
Pressure-powered lifting device. Combined question: Which components trigger LOLER and PSSR, if any?; Evidence: Two applicability decisions and integrated controls.
Lift over pressure plant. Combined question: Could impact or collapse compromise pressure containment?; Evidence: Lift path and protection plan.
Shared maintenance. Combined question: Who controls load, pressure and isolation?; Evidence: Joint permit, verification and handback.
How do lifting and pressure controls change across settings?
A warehouse lift, patient hoist, construction crane and industrial boiler have different loads, people and technical limits. Apply the appropriate GB or NI workplace, lifting and pressure routes to the actual activity.
A six-month or twelve-month shorthand does not replace the correct examination scheme or competent judgement. Check who owns the equipment and who has authority to stop use.
| Setting | Credible failure | Specific control |
|---|---|---|
| Warehouse lift truck | Elevated load can fall while steering or brakes also fail. | Check lifting parts under LOLER and other safety parts under PUWER; segregate pedestrians. |
| Care setting hoist | Person can fall or be injured by wrong sling or attachment. | Match person, sling and hoist, plan the transfer and verify current examination. |
| Construction lift | Ground, reach and wind can exceed configuration. | Competent lift plan, rated setup and exclusion zone. |
| Boiler or autoclave | Pressure, heat or failed protection can release energy. | Safe limits, written scheme and competent examination before operation. |
Which Great Britain law applies to these decisions?
In Great Britain, PUWER 1998 provides the work-equipment baseline, LOLER 1998 adds lifting duties, and PSSR 2000 adds pressure-system duties where each applies; HSWA and Management Regulations support risk assessment and safe systems.
Use current amended legal text and HSE guidance. L22, L113 and L122 are Approved Code of Practice (ACOP) and guidance with specific status; product-supply regimes are separate. Applicability and exceptions require a competent review. See Provision and Use of Work Equipment Regulations 1998.
| GB route | Decision | Source |
|---|---|---|
| PUWER 1998 | Safe work-equipment use. | SI 1998/2306 and L22. See Provision and Use of Work Equipment Regulations 1998. |
| LOLER 1998 | Lifting plan, equipment and examination. | SI 1998/2307 and L113. See Lifting Operations and Lifting Equipment Regulations 1998. |
| PSSR 2000 | Safe limits, written scheme and examination. | SI 2000/128 and L122. See Pressure Systems Safety Regulations 2000. |
| Product supply | Market placement and conformity. | Current sector guidance. See GOV.UK placing UKCA or CE marked products on the Great Britain market. |
Which Northern Ireland law applies to these decisions?
In Northern Ireland, PUWER NI 1999, LOLER NI 1999 and PSSR NI 2004 are separate legal routes; HSENI approves L122 for use with NI pressure-system law, while product-supply questions must follow the applicable NI market rules.
Do not label the GB regulations as UK-wide. Check current NI legal effects and HSENI guidance, identify the actual system and operation, and seek competent NI advice before operational use. See Provision and Use of Work Equipment Regulations Northern Ireland 1999.
| NI route | Decision | Source |
|---|---|---|
| PUWER NI 1999 | Safe work-equipment use. | SR 1999/305. See Provision and Use of Work Equipment Regulations Northern Ireland 1999. |
| LOLER NI 1999 | Lifting planning and examination. | SR 1999/304. See Lifting Operations and Lifting Equipment Regulations Northern Ireland 1999. |
| PSSR NI 2004 | Safe limits and written scheme. | SR 2004/222. See Pressure Systems Safety Regulations Northern Ireland 2004. |
| L122 in NI | ACOP approval context. | HSENI approval page. See HSENI L122 approved for use in Northern Ireland. |
How should management arrangements be checked?
Assign responsibility, assess the actual risk, implement controls, monitor whether they work and review after change or failure.
HSE’s Plan, Do, Check, Act guidance supports management review. It does not replace topic-specific law, technical assessment or competent sign-off.
How should work equipment be controlled across its life?
Control starts with need and specification, continues through purchase or hire, acceptance, installation, use, inspection, maintenance and change, and ends with safe decommissioning or disposal.
Treat each transfer as an evidence gate. A check at purchase does not cover later deterioration, modification, relocation, new attachments, changed users or a different environment.
Select. Critical question: Is this the right equipment and control concept?; Evidence: Specification and risk decision.
Accept and install. Critical question: Is identity, condition and setup proven?; Evidence: Acceptance and commissioning.
Use and maintain. Critical question: Does it remain safe in real work?; Evidence: Checks, defects, maintenance and inspection.
Change or retire. Critical question: Has risk changed or energy been removed?; Evidence: Change review or decommission record.
Which hazards must the equipment assessment cover?
Assess mechanical contact and ejection together with electrical, pressure, thermal, chemical, ergonomic, noise, vibration, fire, explosion, mobility, stability and work-at-height hazards that the equipment or task can create.
Consider normal production, foreseeable abnormal events, clearing blockages, tool change, cleaning, testing, breakdown, maintenance and recovery after a stop. People nearby can be exposed even when they do not operate the equipment.
Mechanical. Examples: Crushing, shearing, cutting, entanglement, drawing-in, ejection.; Control question: Can access or energy be prevented?
Energy. Examples: Electricity, pressure, gravity, heat, stored motion.; Control question: Can every source be isolated and dissipated?
Exposure. Examples: Dust, fume, noise, vibration, substances.; Control question: Which separate regime and source control apply?
Context. Examples: Mobility, stability, falls, traffic, fire.; Control question: What environment and interface change the risk?
How should suitable equipment be selected?
Select equipment that is suitable for the intended task, people, environment, loads and conditions, with risks controlled by design and compatible guards, controls, attachments and information.
Prefer eliminating hazardous operations or choosing safer equipment before adding procedural controls. Include cleaning, maintenance, access, foreseeable misuse and emergency recovery in the selection decision.
Task and capacity. Question: Can it do the work within maker limits?; Reject or hold when: Duty or attachment is unclear.
People. Question: Can intended users operate and maintain it safely?; Reject or hold when: Access, reach or competence is unsuitable.
Environment. Question: Is it suitable for wet, dusty, explosive or public conditions?; Reject or hold when: Protection or compatibility is unproven.
Lifecycle. Question: Can it be inspected, isolated and maintained?; Reject or hold when: Safe intervention cannot be achieved.
What does a conformity mark prove?
A conformity mark supports the applicable product-supply process; it does not prove that equipment is suitable for a particular workplace, correctly installed, maintained, guarded for every task or safe after modification.
In Great Britain, current guidance recognises UKCA and CE routes within their stated scope. In Northern Ireland, use the current CE or CE and UKNI route as applicable. Always check sector-specific rules and current dates.
Declaration and marking. What it supports: Product-supply conformity route.; What it cannot replace: Task suitability and risk assessment.
Instructions. What it supports: Intended use and residual risk information.; What it cannot replace: Safe local installation and supervision.
Workplace acceptance. What it supports: Condition and integration at the site.; What it cannot replace: Required ongoing maintenance and inspection.
How should equipment be accepted before first use?
Verify identity, condition, documentation, correct market route where relevant, intended use, guards, controls, accessories, installation needs, inspection status and support before the equipment enters service.
Record deviations and quarantine anything damaged, incomplete, unexpectedly modified or unsupported. Delivery paperwork alone is not a commissioning record.
Identity and specification. Evidence: Model, serial or asset reference and intended duty.; Hold point: Mismatch or unknown origin.
Condition and completeness. Evidence: Damage check, guards, accessories and instructions.; Hold point: Missing or damaged safety part.
Legal and support route. Evidence: Applicable supplier documents and service support.; Hold point: Wrong market route or no critical information.
Workplace readiness. Evidence: Installation, risk assessment and training plan.; Hold point: Site prerequisites absent.
What belongs in a pre-use check?
A pre-use check should cover visible condition, correct setup and attachment, guards and protective devices, controls, cables or hoses, stability, work area and any equipment-specific indicator identified by the assessment or manufacturer.
A quick user check is not a substitute for a formal inspection. Its content and record depend on risk, equipment and the organisation's system; do not invent a universal checklist or sign-off interval.
Condition. Example observation: Damage, wear, leakage or loose part.; Action: Stop and report if safety may be affected.
Safeguards. Example observation: Guard or device missing, open or defeated.; Action: Do not use; quarantine.
Controls. Example observation: Start, stop or indication abnormal.; Action: Hold pending competent decision.
Area and task. Example observation: Wrong attachment, unstable base or people exposed.; Action: Correct conditions before start.
How should equipment be monitored during use?
Use equipment only for the assessed task and conditions, keep safeguards in place, maintain exclusion and stability, watch for abnormal sound, movement, heat, vibration, leakage or control response, and stop before investigating a change.
Do not reach through a guard, defeat a device, clear a blockage live or rely on familiarity. A change in material, attachment, operator, environment or production method can invalidate the starting decision.
Unexpected movement or ejection. Immediate response: Stop from a safe position.; Next decision: Quarantine and investigate.
Guard or device changes state. Immediate response: Stop work and keep clear.; Next decision: Competent safeguarding review.
Abnormal noise, heat or vibration. Immediate response: Stop without close diagnosis.; Next decision: Maintenance assessment.
Task or environment changes. Immediate response: Pause the job.; Next decision: Reassess method and suitability.
What should happen when work finishes?
Stop the equipment through the defined sequence, leave moving and stored energy controlled, clean without entering danger, record defects or restrictions, and hand back the equipment and area in a known state.
Completion is not permission for maintenance. Any intervention requiring access to danger or stored energy needs its own isolation and authorised method.
Normal stop. Expected state: Movement ceases through intended control.; Evidence: User observation.
Secure and clean. Expected state: No unintended access, restart or unsafe residue.; Evidence: Task completion check.
Report. Expected state: Defects and restrictions are visible to the next user.; Evidence: Tag, log or handover.
Hand back. Expected state: Named owner accepts status.; Evidence: Release or continued hold.
What is the guarding hierarchy?
Prevent access to dangerous parts with fixed guards where practicable, then use other guards or protection devices, then jigs, holders or push-sticks, with information, instruction, training, supervision and PPE only for remaining risk.
A guard must be suitable, effective, maintained, not easily bypassed and not create a new hazard. Guard design and safe distance are equipment-specific engineering decisions, not values to copy from this guide.
| Priority | Control | Boundary |
|---|---|---|
| 1 | Fixed guard. | Use where practicable and compatible with necessary access. |
| 2 | Other guard or protection device. | Must fail or act to a safe condition as designed. |
| 3 | Jig, holder, push-stick or similar aid. | Keeps the person from danger where higher controls cannot fully apply. |
| 4 | Information, training, supervision and PPE. | Residual layer, not a substitute for practicable safeguarding. |
How should interlocks and protective devices be managed?
Protective devices must be selected for the risk, correctly installed, effective, maintained and used; a bypassed, defeated, poorly aligned or unreliable device is a stop and quarantine condition.
Do not tape, wedge, bridge, override or programme around a device to maintain production. Diagnostic or test modes require a designed safe method, restricted authority and equipment-specific controls.
Device functions normally. Meaning: Only evidence for the tested safeguard function.; Response: Continue within assessed use.
Intermittent trip. Meaning: Possible fault or changing condition.; Response: Stop, quarantine and diagnose safely.
Bypass found. Meaning: Safeguard no longer reliable.; Response: Isolate as needed and escalate.
Reset restores operation. Meaning: Does not explain cause.; Response: Investigate before release.
What makes starting, stopping and operating controls safe?
Controls should be identifiable, appropriate, reachable from a safe position, protected against unintended operation where needed, and arranged so starting occurs only through deliberate action and stopping brings equipment to a safe state.
The operator must understand normal stop, emergency response, reset and restart. A reset should not itself create hazardous movement unless the assessed control design specifically provides safe conditions.
Start. Expected behaviour: Deliberate action with danger zone clear.; Verification: Commissioning and user check.
Normal stop. Expected behaviour: Brings operation to intended safe state.; Verification: Functional test.
Mode or selector. Expected behaviour: Controls access and authority for the chosen mode.; Verification: Restricted setting and instruction.
Restart. Expected behaviour: No unexpected movement after interruption or reset.; Verification: Cause and safe-state check.
What is an emergency stop for?
An emergency stop is additional rapid protection, not normal stopping or full isolation. After use, move clear, warn and report, exclude people and control connected equipment; do not reset, enter or investigate until authorised people apply equipment-specific energy isolation. The named operating owner releases only after cause, repair, safeguard and controlled-test evidence is accepted.
After use, keep people clear, establish the plant state and investigate the event. Releasing or resetting an emergency stop does not prove the machine is safe and must not by itself restart hazardous motion.
When is it used? Answer: For an emergency requiring rapid stop.; Boundary: Not the routine production stop.
What does it do? Answer: Acts with priority as designed.; Boundary: May not remove every energy source.
Does it isolate? Answer: Not necessarily.; Boundary: Apply the full isolation procedure.
Can it be reset and run? Answer: Only after cause and safe state are verified.; Boundary: Named return-to-service authority governs.
How should equipment be isolated?
Identify every energy source, stop and separate the equipment, prevent reconnection or release, dissipate or restrain stored energy, verify the safe state, control the work and restore only through the authorised sequence.
Electrical isolation alone may leave hydraulic, pneumatic, pressure, thermal, gravity, spring, rotational or process energy. The actual isolation points, verification method and lock-off arrangements must come from competent equipment-specific planning.
| Energy or stage | Control question | Evidence |
|---|---|---|
| Identify | What can move, energise, pressurise, heat or release? | Energy map and instructions. |
| Separate and secure | Can reconnection or release be prevented? | Isolation and lock-off record. |
| Dissipate or restrain | What stored energy remains? | Verified zero or safely restrained state. |
| Restore | Are people clear and safeguards restored? | Controlled handback and release. |
How should maintenance be planned?
Plan maintenance as work in its own right: define scope, condition, isolation, access, competence, tools, parts, coordination, testing, safeguards and handback before intervention begins.
Maintain equipment in an efficient state and good repair. Where maintenance cannot be done at rest, use an equipment-specific safe method and protection designed for that task; routine production pressure never supplies the justification.
Prepare. Control: Scope, hazards, safe state and people.; Evidence: Work order or task plan.
Intervene. Control: Isolation, access, tools and coordination.; Evidence: Permit or maintenance record.
Test. Control: Controlled test with restricted exposure.; Evidence: Functional and safeguard results.
Hand back. Control: Covers, guards and settings restored.; Evidence: Named acceptance and release.
When is a work-equipment inspection needed?
Inspect after installation where safety depends on installation, after assembly at a new site where applicable, and at suitable risk-based intervals or after exceptional circumstances that may jeopardise safety.
Frequency depends on the equipment, use, conditions, deterioration, manufacturer information and experience. This guide sets no blanket daily, weekly, annual or other interval.
Installation or assembly. Purpose: Prove safe installation before use.; Decision basis: Equipment and installation dependency.
Deterioration risk. Purpose: Detect safety-relevant decline in time.; Decision basis: Risk, use, conditions and experience.
Exceptional event. Purpose: Assess damage or loss of integrity.; Decision basis: Accident, modification, long disuse or severe condition.
User check. Purpose: Identify obvious immediate defects.; Decision basis: Separate from formal inspection where required.
What should happen when a defect is found?
Stop use where safety may be affected, bring the equipment to a controlled state, prevent further use, identify the defect, protect others, report it and keep it quarantined until competent evidence supports release.
Do not remove a tag, swap a guard, clear a jam or press reset as an informal return to service. The severity, affected equipment and connected systems must be understood first.
Immediate danger. Action: Stop, keep clear and isolate if safe and trained.; Release condition: Emergency or competent recovery route.
Safety device or guard defect. Action: Quarantine equipment.; Release condition: Repair and safeguarding verification.
Condition uncertain. Action: Treat as held.; Release condition: Competent inspection and evidence.
Minor non-safety issue. Action: Record and manage under local system.; Release condition: Decision still documented.
What must each role learn and demonstrate?
Competence must match the decision and consequence of error. Attendance alone does not show that a worker, manager or specialist can recognise a stop condition, select a control and verify it in practice.
Use observed tasks and scenario questions. Reassess after change, defect, incident or a materially different role, and seek a specialist for technical or legal decisions outside local competence.
| Role | Demonstrated decision | Reassessment trigger |
|---|---|---|
| Worker or operator | Explain the task risk, pre-use check and when to stop. | New task, equipment or unsafe event. |
| Supervisor or manager | Select and verify controls, allocate resources and act on reports. | Work pattern, staffing, process or equipment change. |
| Maintainer or specialist | Show the technical basis, safe state, examination or referral within own competence. | Modified system, failed test or new evidence. |
| Safety adviser or auditor | Trace law, hazard, control and field evidence without substituting a checklist for judgement. | Regulatory or technical change. |
How should modification and change be controlled?
Keep modified, relocated, integrated or reprogrammed equipment out of normal work until the affected scope and product-supply duties are resolved, safeguards restored, applicable inspection or examination and controlled tests pass, and the named operating owner records release. A diagnostic or commissioning test under a separate controlled plan is not production permission.
A change that appears to improve output can alter stability, access, stopping, control logic, load, exposure or maintenance. Keep the equipment held until technical, operational and legal boundaries are resolved.
New attachment or duty. Workplace-use question: Is equipment still suitable and guarded?; Product-supply question: Does intended use or conformity scope change?
Control or software change. Workplace-use question: Are modes, stops and restart safe?; Product-supply question: Who now takes manufacturer responsibility?
Refurbishment. Workplace-use question: Is condition and performance demonstrated?; Product-supply question: Is it substantially changed or newly supplied?
Integration. Workplace-use question: Are whole-system risks controlled?; Product-supply question: Does an assembly become a new product?
What training and competence are needed?
Users, supervisors and those who manage, inspect, maintain or modify equipment need adequate information, instruction and training for their role, with competence demonstrated for the actual equipment and task.
Simple equipment may be covered by suitable in-house instruction; complex or high-risk work may need specialist training and supervised experience. There is no universal certificate or refresher expiry.
User. Competence content: Normal use, checks, limits, defects and emergency response.; Review trigger: New equipment, task or performance concern.
Supervisor. Competence content: Authorisation, observation, stop and release.; Review trigger: Change or control failure.
Maintainer or inspector. Competence content: Technical method, isolation and judgement.; Review trigger: Design change or scope extension.
Manager or purchaser. Competence content: Suitability, interfaces and assurance.; Review trigger: New process, supplier or regime.
What should supervision verify?
Supervision should verify authorised people, correct equipment and setup, guards and controls, the actual method, conditions during use, defect response and handback, with closer oversight where competence or risk requires it.
Supervision is an active control, not a signature. It should detect drift such as routine bypassing, wrong attachments, informal repairs, missed checks or production pressure overriding a hold.
Start. Observation: Identity, setup, guards and people.; Response: Permit or hold.
Work. Observation: Real behaviour and machine response.; Response: Coach, correct or stop.
Change. Observation: New material, mode or environment.; Response: Pause and reassess.
Finish. Observation: Defects, state and handback.; Response: Release or quarantine.
Who is responsible for hired work equipment?
Hiring does not remove workplace-use duties: the supplier or hirer may have supply and maintenance obligations, while the employer or person controlling use must still ensure suitability, safe condition, inspection evidence, competence and safe operation.
Agree in writing who selects, delivers, inspects, maintains, responds to defects and removes the equipment. Verify the agreement against what arrives and how it will actually be used.
Supplier or hire company. Question: What is supplied, maintained and documented?; Evidence: Specification, instructions and inspection evidence.
Hiring organisation. Question: Is it suitable for the actual workplace and task?; Evidence: Acceptance and risk assessment.
User and supervisor. Question: Are setup, competence and daily condition controlled?; Evidence: Briefing, checks and defect route.
Breakdown or return. Question: Who makes safe and who authorises movement?; Evidence: Call-out, isolation and handover.
How should contractor equipment be controlled?
The host and contractor should exchange task, site, equipment, competence, inspection, maintenance, isolation, emergency and defect information, then agree who controls each decision before work starts.
A contractor-owned machine is not automatically acceptable, and a host permit does not prove its condition. Shared or connected systems need one coordinated safe state and clear release authority.
Verify equipment and documents. During work: Coordinate exclusions and site conditions.; Handback: Report defects and restrictions.
Agree isolation and emergency interfaces. During work: Stop on mismatch or unsafe change.; Handback: Jointly confirm equipment and area state.
Name decision owners. During work: Protect other employers and the public.; Handback: Retain required evidence.
Which specialised regimes may also apply?
PUWER is not a complete answer where equipment lifts loads or people, contains pressure, uses electricity, supports work at height, creates substances, noise or vibration, or can ignite a dangerous atmosphere.
Determine applicability for the real equipment and task in the correct jurisdiction. Sector regimes for construction, mines, quarries, agriculture, rail or merchant shipping may also change duties and enforcement routes.
Lifting loads or people. Additional route: LOLER or NI equivalent as applicable.; Boundary: Separate thorough-examination and planning decisions.
Pressure or electricity. Additional route: Pressure-systems or electrical-safety law.; Boundary: Specialist integrity and isolation.
Work at height. Additional route: Work-at-height law.; Boundary: Access selection and fall prevention.
Dust, fume, noise, vibration or flammables. Additional route: COSHH, DSEAR, noise or vibration law.; Boundary: Separate exposure and ignition decisions.
What should happen in a work-equipment emergency?
Raise the alarm, stop or isolate only through trained actions that are safe from the person's position, keep people out of danger, call the site emergency route and preserve the equipment state for competent recovery and investigation.
Do not approach moving, energised, pressurised, hot, unstable or damaged equipment to diagnose it. Rescue, firefighting and first-aid actions must follow the site plan and trained roles.
Person in danger. Immediate action: Raise alarm and use designed emergency control if safe.; Prohibited assumption: Do not enter the danger zone.
Unexpected movement or release. Immediate action: Keep clear and stop connected work.; Prohibited assumption: Emergency stop is not full isolation.
Fire, pressure or electrical event. Immediate action: Use the site emergency plan.; Prohibited assumption: Do not improvise specialist response.
After the event. Immediate action: Maintain exclusion and control evidence.; Prohibited assumption: No restart because conditions appear normal.
Who may return equipment to service?
The named operating owner should authorise return only after the cause is understood, repairs and safeguards are complete, inspection or testing matches the defect and risk, people are clear, documentation is updated and restrictions are communicated.
Repair completion, a reset, a replaced fuse, an inspection sticker or production need is not enough by itself. Serious events or modifications may require engineering, safeguarding, electrical, pressure, lifting or legal review.
Cause. Required evidence: Defect or event understood.; Owner: Competent investigator or specialist.
Restoration. Required evidence: Repair and safeguards verified.; Owner: Maintainer and tester.
Readiness. Required evidence: Method, competence, area and interfaces ready.; Owner: Supervisor and affected parties.
Authorisation. Required evidence: Signed or recorded release.; Owner: Named operating owner.
Who owns each work-equipment decision?
Assign owners for specification, acceptance, use, inspection, maintenance, isolation, modification, quarantine, emergency control and return to service; do not let responsibility disappear between departments or companies.
One person may hold several roles, but the evidence and competence requirements remain distinct. Emergency command and later operational release are separate decisions.
Specification and acceptance. Typical owner: Purchaser and technical owner.; Interface: User and maintenance input.
Use and supervision. Typical owner: Operating manager or supervisor.; Interface: Worker and nearby people.
Inspection and maintenance. Typical owner: Competent person and asset owner.; Interface: Defect and isolation system.
Return to service. Typical owner: Named operating owner.; Interface: Technical evidence and affected parties.
How should work-equipment control be assured?
Assurance should test whether equipment is suitable, safeguards work, defects are controlled, inspections and maintenance match risk, competence is real, contractor interfaces work and return-to-service decisions are evidence based.
Use field observation and equipment sampling, not record presence alone. Trend repeated guard damage, bypasses, emergency stops, overdue actions, recurring faults and differences between shifts or sites.
Is the inventory complete? Evidence: Assets, location, owner and status.; Escalation: Unknown equipment held.
Do safeguards work in practice? Evidence: Observed use and functional evidence.; Escalation: Bypass or drift quarantined.
Are defects closed? Evidence: Traceable report, repair and release.; Escalation: Repeat or overdue issue reviewed.
Are people competent? Evidence: Demonstration and supervision.; Escalation: Restriction or refresher based on need.
Which warning signs require immediate attention?
Missing or defeated guards, unexpected movement, unreliable controls, recurring trips, damaged cables or hoses, leaks, unstable equipment, unknown modifications, expired required evidence or informal repairs require a stop, hold or competent review.
Also treat emergency-stop use, reports that workers must reach into danger, and workarounds that have become normal as control failures rather than operator inconvenience.
Guard opened or removed for production. Likely weakness: Safeguarding and workflow conflict.; Action: Stop and redesign or restore.
Frequent reset or emergency stop. Likely weakness: Unresolved fault or process instability.; Action: Quarantine and investigate.
Temporary tape, wedge or bridge. Likely weakness: Device defeated.; Action: Prevent use and escalate.
Inspection or modification unclear. Likely weakness: Evidence gap.; Action: Hold pending competent decision.
What do complete work-equipment decisions look like?
Four complete BuildOut Ltd cases cover routine guarded-drill work, hired mobile equipment, an overhead-hoist evidence mismatch and a changed compressed-air system. The four scenario-type summaries are decision prompts, not ten worked cases. Actual equipment, jurisdiction, examination evidence and named authorisation govern.
BuildOut Ltd could use one asset lifecycle with risk-based gates for specification, acceptance, authorisation, use, defects, maintenance, inspection, change and release, while applying the correct GB or NI and specialist regime at each site.
How could BuildOut Ltd govern work equipment?
The teaching model keeps operations, engineering, procurement and contractors connected. It does not replace equipment-specific instructions, examinations, limits or site authority.
Specify. BuildOut owner: Procurement plus technical and user leads.; Minimum evidence: Task, environment and safeguard requirements.
Accept. BuildOut owner: Asset owner and competent installer.; Minimum evidence: Identity, condition, documentation and commissioning.
Operate. BuildOut owner: Supervisor and authorised user.; Minimum evidence: Checks, competence and method.
Hold and release. BuildOut owner: Operating owner with technical evidence.; Minimum evidence: Defect closure and recorded authorisation.
Each example is a training pattern, not an equipment permission. Replace every example details with the real machine, manufacturer instructions, energy sources, people, environment, inspection status and named authority.
| Scenario type | Primary decision | End state |
|---|---|---|
| Routine use | Start only after suitability, safeguards and checks pass. | Controlled completion. |
| Hire or contractor | Accept only after duties and evidence align. | Accepted, rejected or held. |
| Defect or emergency | Stop and prevent restart. | Quarantine or authorised return. |
| Maintenance or change | Control energy and evidence. | Verified handback. |
Routine guarded pillar-drill task
Task material and setting: Training only, not authorisation for a real drill. An authorised user checks the task, material, workholding, guard, controls and area before use. Stop and hold for a loose workpiece, damaged bit, guard or control defect, unusual response or intrusion; never adjust while moving. Use the normal stop, wait for movement to cease and record defects. The workshop supervisor accepts the pre-use, briefing, defect-closure and safe handback evidence before release under the applicable GB or NI PUWER route.
People and prerequisites: Authorised user and workshop supervisor; suitable drill, correct workholding and bit, current local assessment, functioning guard and controls, safe area and known defect route.
Before: Confirm the task and material, inspect the drill, guard, workholding and emergency control, remove loose items, set the work securely and keep others outside the operating space.
During: Keep the guard and workholding in position, use the intended controls, observe sound, movement and swarf, and stop before any adjustment or clearing.
Hold or stop: Do not start or continue for a loose workpiece, damaged bit, missing or defeated guard, unreliable control, unusual movement, unexpected material response or unauthorised person in the area.
Completion and hand back: Stop through the normal control, wait for movement to cease, leave the machine and area clean through the safe method, record any defect and hand back in a known state.
Evidence: Authorisation, pre-use check, task briefing, any defect report and supervisor release.
Hired mobile equipment arrives on site
Task material and setting: Training only, not permission to operate hired plant. Keep the platform out of service while identity, condition, instructions, applicable PUWER inspection and LOLER examination evidence, ground, route, weather, rescue plan and competence are checked. Reject or quarantine any mismatch or uncertainty; obtain supplier and competent site clarification. The site supervisor accepts use only on the actual evidence and records defects and return handover.
People and prerequisites: Hire supplier, site logistics lead, competent equipment assessor, authorised operator and supervisor; agreed specification, delivery evidence, site assessment, ground and route plan, rescue and defect arrangements, and any specialised examination evidence required.
Before: Match the delivered machine to the order, inspect condition and documentation, verify inspection or examination evidence applicable to the machine, confirm ground, access, weather and interface controls, and brief the authorised operator.
During: Use only within manufacturer and site limits, maintain route and people controls, observe stability and machine response, and stop for changed ground, weather, load, alarm or condition.
Hold or stop: Reject or quarantine the equipment for identity mismatch, damage, missing safety information, uncertain inspection or examination status, wrong attachment, unsuitable ground, unavailable rescue arrangements or unverified operator competence.
Completion and hand back: Park and secure through the agreed method, record condition and defects, prevent further use where held, and complete a joint handover to the supplier or site owner.
Evidence: Hire specification, delivery and acceptance record, applicable inspection or examination evidence, operator authorisation, daily checks, defect history and return handover.
Overhead hoist: accessory identity does not match the report
Task material and setting: Workshop lift of a fabricated frame. The planned sling identity differs from the available examination report; no load is lifted.
People and prerequisites: Lifting planner, competent examiner and operating owner; actual load/configuration, suitable equipment, lift plan and applicable GB or NI examination route.
Before: Match hoist and accessory identities, capacity/configuration and required reports to the planned lift; check site conditions and operator competence.
During: Keep the lift on hold while the supplier and competent examiner resolve the mismatch. Do not trial the lift to prove the sling is sound.
Hold or stop: Missing identity, scope mismatch, unresolved defect or changed configuration prevents lifting.
Completion and hand back: The operating owner releases only after matching accepted evidence, any required examination/defect closure, a checked lift plan and team briefing.
Evidence: Asset/accessory identities, relevant examination report, defect disposition, plan and named release record.
Changed compressed-air system: scheme coverage unresolved
Task material and setting: Installed compressed-air receiver with changed connected pipework and protection. The existing written scheme has not been confirmed to cover the changed system; pressure operation is held.
People and prerequisites: Installed-system user, competent pressure-system person and authorised engineering team; fluid, boundary, modifications and applicable GB or NI PSSR scope established.
Before: Compare actual system identity, relevant fluid, protective devices and change record with safe-limit and scheme documentation.
During: Keep pressure operation prohibited while the competent person reviews scheme coverage, examination needs and protection evidence. Control maintenance energy through the approved system-specific method.
Hold or stop: Unknown scope, absent required scheme/examination evidence, unresolved protection or limits prevents use; no generic pressure setting is supplied.
Completion and hand back: The responsible user authorises operation only after accepted safe-limit evidence, a suitable written scheme, required completed examination, closed defects and operator briefing.
Evidence: System boundary/change record, scheme version, examination findings, protection verification, instructions and named user release.
Further specialist discussion prompts
The previously advertised hired-MEWP report mismatch and unexpected autoclave vent remain useful discussion prompts, rather than completed additional cases here. A report mismatch holds the equipment pending identity/scope resolution; an unexpected vent requires the site’s safe stop or emergency route and competent pressure-system investigation before a separately authorised return. General guarding, maintenance, unknown modification and emergency-stop interfaces remain in the existing scenario summaries and main guidance; none supplies permission for the actual equipment.
What do the acronyms and key terms mean?
Keep work equipment, use, guard, protection device, emergency stop, isolation, inspection, maintenance, competent person, quarantine and return to service distinct.
| Term | Meaning | Boundary |
|---|---|---|
| Work equipment | Machinery, appliance, apparatus, tool or installation used at work. | Scope depends on real use. |
| Guard | Physical barrier preventing or restricting access to danger. | Design is equipment specific. |
| Protection device | Control or sensing function that reduces risk. | Must not be bypassed. |
| Emergency stop | Additional rapid stop function where appropriate. | Not full isolation. |
| Isolation | Separation and control of all relevant energy. | Includes stored energy. |
| Inspection | Competent check to detect safety-relevant deterioration or installation issues. | Not the same as maintenance. |
| Quarantine | State preventing further use pending decision. | Release needs evidence and authority. |
| Return to service | Recorded operational acceptance after restoration. | Repair alone is insufficient. |
| PUWER | Provision and Use of Work Equipment Regulations; separate GB and NI instruments. | General workplace equipment duty route. |
| LOLER | Lifting Operations and Lifting Equipment Regulations; separate GB and NI instruments. | Planning, safe use, marking and thorough examination of lifting equipment. |
| PSSR | Pressure Systems Safety Regulations; separate GB and NI instruments. | Safe limits and written-scheme examination where applicable. |
| WSE | Written scheme of examination for qualifying pressure systems. | A competent person defines the parts, nature and frequency of examination. |
| SWL | Safe working load. | Check the actual equipment configuration and marked limit. |
| ACOP | Approved Code of Practice. | Check approved edition and jurisdiction. |
| ERICPD | Eliminate, Reduce including substitution, Isolate, Control, personal protective equipment, Discipline. | A SHARE decision prompt; sustain effective controls and learning. |
| PPE | Personal protective equipment. | Use for assessed residual exposure; it does not replace stronger feasible controls. |



Unlock another resource
You have used this month’s two free downloads. Publish a post in your own words to unlock one more resource, or choose SHARE Individual for 10 downloads per month.
You decide whether to share. If you do, use the relevant platform disclosure tools and do not make claims you do not genuinely hold.