SHARE Knowledge Hub
Health and Safety Policy
A health and safety policy sets out how an employer will manage risk, who owns decisions and which practical arrangements make the commitment real. In both Great Britain and Northern Ireland, employers with five or more employees must record the policy in writing and communicate it. A useful policy connects leadership intent to risk assessment, consultation, competence, monitoring and review, and is tested against the work people do.
Understanding Health and Safety Policy
A health and safety policy states an organisation's overall direction, who is responsible and how it will manage risk in practice.
Why this matters at work
Describe the office’s actual work, staff, visitors, contractors and any remote arrangements. Set out intent, named responsibilities and practical arrangements that fit its material risks. Do not promise technical inspections or procedures that the business does not provide. Decide who can arrange competent advice, fund improvements and respond to concerns. Communicate the policy in a usable form and check whether staff understand the relevant responsibilities. Record adoption and subsequent changes; the source example is a teaching aid and supplies no evidence about this office.
Name positions and, where useful, current postholders responsible for health and safety decisions. State what the employer or board, managers, supervisors, competent advisers, workers, representatives, first aiders and emergency roles do. Focus on decisions: who assesses a new process, who can stop a defective machine, who funds repair, who verifies restart and who coordinates a contractor. HSE's policy-writing page asks for names, positions and roles of people with specific responsibilities. A chart that names everyone but leaves authority unclear is not useful.
How organisations manage this in practice
Identify which overdue items leave a significant control gap and what protection is needed now. Assign actions to roles able to obtain resources and competent assistance, rather than merely forwarding the list. Investigate repeated delays or administrative closures and report them to someone with decision authority. Verify improvements in actual use and communicate changes to affected staff. Retain the policy review decision and its evidence. A new signature or annual review date cannot establish that the promised repair or preventive arrangement exists.
For a press, eliminate hand access or engineer guarding before relying on instructions; for a bodyshop, substitute or enclose and extract hazardous spray before relying on RPE; for a warehouse, segregate people and vehicles before adding high-visibility clothing.
Do not say employers with fewer than five employees have no health and safety duties, that a signed policy transfers duty to a safety adviser, that a template is sufficient without site adaptation, or that an annual signature alone fulfils an appropriate-revision duty.
What are the key points for health and safety policy?
A policy should explain intent, responsibilities and arrangements in a way that changes what people do.
What are the key points for health and safety policy? — part 1 of 2
Read the complete visual as text
- A policy should explain intent, responsibilities and arrangements in…: A policy should explain intent, responsibilities and arrangements in a way that changes what people do.
- Intent needs action: A commitment is weak unless arrangements make it happen.
- Responsibilities must be named: People need to know who owns decisions, controls and review.
What are the key points for health and safety policy? — part 2 of 2
Read the complete visual as text
- Arrangements are the working part: They explain how risk assessment, training, consultation, monitoring and review happen.
- Objectives should be measurable: SMART targets help policy drive improvement rather than decoration.
- Policy must stay current: Change, incidents and audit findings should trigger review.
Intent needs action
A commitment is weak unless arrangements make it happen.
Responsibilities must be named
People need to know who owns decisions, controls and review.
Arrangements are the working part
They explain how risk assessment, training, consultation, monitoring and review happen.
Objectives should be measurable
SMART targets help policy drive improvement rather than decoration.
Policy must stay current
Change, incidents and audit findings should trigger review.
What does a health and safety policy mean?
A health and safety policy is the organisation's written or stated approach to managing health and safety in practice.
The policy should be simple enough for people to understand and specific enough to guide decisions. It should not try to hold every procedure. Its job is to set direction, define responsibility and point to the practical arrangements that control risk.
A good policy links to the wider management system. If it promises safe contractors, the arrangements should explain contractor selection, induction, permits, supervision and review. If it promises worker involvement, the arrangements should say how consultation happens and how feedback is closed.
| Question | Good answer | Weak answer |
|---|---|---|
| What is our commitment? | Prevent harm and manage significant risks proportionately. | Safety is our top priority. HSE prepare a health and safety policy |
| Who is responsible? | Named roles with authority and duties. | Everyone is responsible. HSE prepare a health and safety policy |
| How will we do it? | Risk assessment, competence, controls, monitoring and review. | Follow procedures. HSE prepare a health and safety policy |
| How will people know? | Briefing, induction, consultation and accessible copies. | Policy is on the intranet. HSE prepare a health and safety policy |
| How will it improve? | Objectives, audits, incident learning and management review. | Annual signature only. HSE prepare a health and safety policy |
A policy names the commitment, decision owners and arrangements that keep visitors out of vehicle routes. HSE prepare a health and safety policy
What does the law require for health and safety policy?
Employers need a health and safety policy; in both Great Britain and Northern Ireland, those with five or more employees must write it down.
HSE guidance explains that a health and safety policy sets out the general approach to health and safety and how the employer will manage it. It should say who does what, when and how, and it must be shared with employees.
The legal point is not only the document. The policy should be given effect through arrangements. A written policy that nobody understands or uses is weak evidence of management.
| Requirement | Practical meaning | Evidence |
|---|---|---|
| Have a policy | The employer has a clear approach to managing health and safety. | Policy document or stated arrangements. HSE prepare a health and safety policy |
| Write it down if five or more employees | Formal written record is required. | Signed and dated policy. HSE prepare a health and safety policy HSENI health and safety policy |
| Share it with employees | Workers know what applies and what changed. | Induction, briefing and accessible copy. HSE prepare a health and safety policy |
| State responsibilities | People know who does what. | Role table and management structure. HSE prepare a health and safety policy |
| Keep it current | Policy reflects current work and risk. | Review record and change log. HSE prepare a health and safety policy |
The five-employee written threshold applies in both GB and NI; the need to manage vehicle risk applies regardless of headcount. HSE prepare a health and safety policy
What are the three parts of a health and safety policy?
The three parts are statement of intent, responsibilities and arrangements.
The three-part structure is the simplest way to test whether a policy is usable. The statement sets intent, responsibilities name ownership, and arrangements explain how the intent will be delivered.
| Policy part | Purpose | Example content |
|---|---|---|
| Statement of intent | Sets commitment and aims. | Signed commitment to prevent injury and ill health. HSE prepare a health and safety policy |
| Responsibilities | Names roles and accountabilities. | Director, managers, supervisors, workers and advisers. HSE prepare a health and safety policy |
| Arrangements | Explains how the aims are achieved. | Risk assessment, training, consultation, contractors, emergency, monitoring and review. HSE prepare a health and safety policy |
State the intent to separate people and vehicles, name the route owner, and link the physical layout and hold rule. HSE prepare a health and safety policy
What could a simple health and safety policy look like?
Follow one policy promise into the workplace
Illustrative chain: the site director commits resources for separated pedestrian access; the operations manager (deputy: duty manager) owns local traffic arrangement TRA-01. Before opening, the duty manager checks the barrier and crossing against that arrangement. A damaged barrier closes the affected route. The authorised operations manager receives repair and observed-function evidence before reopening, records the decision and sets the review date. This is an original teaching example, not an approved traffic layout.
A simple policy should be specific enough to guide responsibility and arrangements without becoming a full procedure manual.
The example below is deliberately short. A real business would tailor it to its activities, risks, size, locations, workforce and consultation arrangements. The value is in the structure: clear intent, named responsibility and practical arrangements that point to the controls used in the management system.
For learners, this is a useful way to remember that a policy is not only a signed statement. It should show who owns the system and how the organisation will plan, organise, control, monitor and review health and safety.
| Policy part | Example wording | Why it works |
|---|---|---|
| Statement of intent | We will prevent work-related injury and ill health by identifying significant risks, providing competent people and resources, consulting workers and reviewing performance. | It names prevention, resources, consultation and review rather than using a slogan. HSE prepare a health and safety policy |
| Responsibilities | The managing director owns the policy and review. Managers implement arrangements. Supervisors verify controls. Workers follow controls and report defects. The HSE adviser supports and escalates concerns. | It makes roles and authority visible. HSE prepare a health and safety policy |
| Arrangements | We will use risk assessment, contractor control, training, emergency planning, inspection, audit, incident learning and management review to manage our significant risks. | It points to the system elements that make the policy real. HSE prepare a health and safety policy |
| Objectives | We will reduce high-risk manual handling tasks by introducing mechanical aids and verifying use through supervisor checks by 31 December. | It shows a SMART improvement linked to a real risk. HSE prepare a health and safety policy |
| Review | This policy will be reviewed annually and after significant change, incident findings, audit findings or legal/guidance updates. | It avoids the policy becoming stale. HSE prepare a health and safety policy |
A short example should identify who stops a delivery when the entrance route is occupied. HSE prepare a health and safety policy
What should the statement of intent include?
The statement should set the organisation's commitment, aims and leadership accountability in plain language.
A statement of intent should be short, credible and specific. It should make a real commitment to prevention, resources and review rather than relying on slogans that workers and managers cannot apply.
| Element | Good wording approach | Weak wording |
|---|---|---|
| Commitment | Specific commitment to manage risk and prevent harm. | Safety first slogan. HSE prepare a health and safety policy |
| Scope | Covers employees, contractors, visitors and others affected. | Employees only. HSE prepare a health and safety policy |
| Leadership | Most senior person signs and owns review. | Unsigned generic template. HSE prepare a health and safety policy |
| Resources | Acknowledges need for competent people, time and controls. | No link to resources. HSE prepare a health and safety policy |
| Review | States regular and change-triggered review. | Review when convenient. HSE prepare a health and safety policy |
A signed commitment matters when leaders fund a route change and keep visitors away from reversing vehicles. HSE prepare a health and safety policy
How should responsibilities be written?
Responsibilities should be specific enough that people know what they own and what evidence they must provide.
Responsibilities need enough detail for people to understand their authority and evidence requirements. The examples below show how roles differ across directors, managers, supervisors, workers, advisers and contractors.
| Role | Responsibility | Evidence |
|---|---|---|
| Director | Set policy, resources and review performance. | Management review minutes. HSE prepare a health and safety policy |
| Manager | Implement arrangements and close actions. | Action tracker and team briefings. HSE prepare a health and safety policy |
| Supervisor | Verify controls during work and escalate defects. | Inspection and briefing records. HSE prepare a health and safety policy |
| Worker | Follow controls, report defects and cooperate. | Reports, observations and training. HSE prepare a health and safety policy |
| HSE adviser | Advise, support, monitor and escalate within competence. | Audit reports and advice records. HSE prepare a health and safety policy |
| Contractor | Follow site rules and coordinate risk. | RAMS, permits and supervision records. HSE prepare a health and safety policy |
Name who controls bookings, barrier maintenance, driver instruction and authority to hold a delivery. HSE prepare a health and safety policy
What practical arrangements should a policy point to?
Arrangements should describe how the organisation plans, organises, controls, monitors and reviews health and safety.
Arrangements are where policy becomes management practice. They should point readers towards the controls, registers, checks and reviews that actually manage significant risks.
| Arrangement | What it should cover | Evidence |
|---|---|---|
| Risk assessment | How risks are assessed, recorded and reviewed. | Assessment register. HSE separating pedestrians and vehicles |
| Competence and training | Role requirements, assessment and refresher training. | Training matrix and competence checks. HSE separating pedestrians and vehicles |
| Consultation | Worker involvement routes and feedback. | Committee notes and action tracker. HSE separating pedestrians and vehicles |
| Contractors | Selection, onboarding, supervision and review. | Prequalification and site monitoring. HSE separating pedestrians and vehicles |
| Emergency arrangements | Fire, first aid, evacuation and serious events. | Plans, drills and equipment checks. HSE separating pedestrians and vehicles |
| Monitoring and audit | Inspections, indicators, audits and management review. | Monitoring schedule and audit reports. HSE separating pedestrians and vehicles |
The policy should point to a site-specific traffic plan, not try to replace the swept-path design. HSE separating pedestrians and vehicles
How should objectives and SMART targets be used?
Completed illustrative SMART objective
Illustrative local objective: the operations manager owns the review of 20 defined high-risk handling tasks at the baseline date. By 31 December 2026, eliminate or redesign at least six so no more than 14 remain in that assessed set. The competent assessor verifies the task changes and any transferred risks; the manager signs off the evidence. Record additions/removals to the task set separately. Briefing attendance alone cannot demonstrate achievement.
Objectives should turn policy intent into measurable improvement that links to significant risk.
A weak objective says 'reduce accidents'. A stronger objective names the risk area, improvement, owner, measure and review date. Objectives should focus on meaningful control improvement, not only injury reduction.
Objectives should also be realistic. A target that can be achieved only by under-reporting is dangerous. Better targets measure action closure, control quality, competence, exposure reduction or audit findings.
| Weak objective | Stronger SMART objective | Why stronger |
|---|---|---|
| Improve safety culture. | Close 90% of worker concern actions within agreed risk-based timescales by quarter end. | Measurable and linked to trust. HSG65 Managing for health and safety |
| Reduce accidents. | Reduce high-risk manual handling tasks by 30% through mechanical aids by December. | Focuses on risk reduction. HSG65 Managing for health and safety |
| Do more training. | Assess all supervisors on permit handback verification by 30 September. | Checks competence, not attendance. HSG65 Managing for health and safety |
| Improve contractors. | Audit the next five high-risk contractor jobs against mobilisation and supervision standards. | Tests the system in real work. HSG65 Managing for health and safety |
Measure verified route separation and closure of pedestrian conflicts, not only the number of briefings. HSG65 Managing for health and safety
How should the policy be communicated?
The policy should be communicated so people understand what it means for their role and work.
Communication should be matched to the audience and the change being made. A policy update may need induction, team briefing, consultation and supervisor conversation, not just an intranet upload.
| Method | Best used for | Good practice |
|---|---|---|
| Induction | New starters and contractors. | Explain role-specific arrangements. HSE prepare a health and safety policy |
| Team briefing | Policy changes and local priorities. | Use examples from the work. HSE prepare a health and safety policy |
| Noticeboards or intranet | Reference and access. | Keep current and easy to find. HSE prepare a health and safety policy |
| Consultation meetings | Feedback and improvement. | Record actions and respond. HSE prepare a health and safety policy |
| Supervisor conversations | Task-level meaning. | Translate policy into control checks. HSE prepare a health and safety policy |
Tell workers, drivers and contractors which route to use and whom to contact when the gate or barrier fails. HSE prepare a health and safety policy
How should a health and safety policy be kept current?
A policy should be reviewed regularly and whenever work, risk, law, people or evidence changes.
Policies should change when the organisation, work, law, risk profile or evidence changes. The triggers below are practical prompts for review rather than waiting for an arbitrary annual date.
| Trigger | Why it matters | Example |
|---|---|---|
| Business change | Roles and risks may change. | New site, service or product. HSE prepare a health and safety policy |
| Incident or near miss | Policy arrangements may have failed. | Investigation finds unclear responsibility. HSE prepare a health and safety policy |
| Audit finding | Evidence shows gap in arrangements. | Contractor procedure not followed. HSE prepare a health and safety policy |
| Legal or guidance update | Duties or expectations may change. | New or revised HSE guidance. HSE prepare a health and safety policy |
| Leadership change | Accountability and signature may need update. | New managing director. HSE prepare a health and safety policy |
| Worker feedback | Arrangements may not fit real work. | Supervisors lack time for checks. HSE prepare a health and safety policy |
Review the arrangement when a supplier changes vehicle size, the entrance moves or a conflict is reported. HSE prepare a health and safety policy
How is a policy different from a procedure?
A policy sets intent and responsibilities; procedures explain how specific activities are controlled.
This distinction helps stop one document doing too much. Policies set direction, while standards, procedures, assessments and checklists translate that direction into practical control.
| Document | Purpose | Example |
|---|---|---|
| Policy | States commitment, responsibilities and arrangements. | Health and safety policy. HSE prepare a health and safety policy |
| Standard | Sets organisational rules for a topic. | Contractor management standard. HSE prepare a health and safety policy |
| Procedure | Explains how a process is carried out. | Permit to work procedure. HSE prepare a health and safety policy |
| Risk assessment | Identifies hazards and controls for specific work. | COSHH or task assessment. HSE prepare a health and safety policy |
| Checklist | Verifies key controls. | Pre-use ladder check. HSE prepare a health and safety policy |
The policy sets responsibility and intent; the traffic procedure gives the safe route and live stop point. HSE prepare a health and safety policy
What evidence shows a policy is working?
Evidence should show that the policy is known, applied, reviewed and linked to real controls.
Evidence should be read as a chain rather than a filing exercise. A single record rarely proves good management on its own; stronger assurance comes from matching records, observations, interviews, trends and verified action closure.
| Evidence | What it can evidence | What to challenge |
|---|---|---|
| Signed current policy | Leadership commitment and review. | Is it generic or current? HSE separating pedestrians and vehicles |
| Communication records | Workers were told and changes shared. | Did people understand it? HSE separating pedestrians and vehicles |
| Responsibility matrix | Ownership is clear. | Do role holders have authority? HSE separating pedestrians and vehicles |
| Arrangement records | Policy links to real controls. | Are arrangements implemented? HSE separating pedestrians and vehicles |
| Audit findings | Policy works or needs improvement. | Are findings closed with evidence? HSE separating pedestrians and vehicles |
| Management review | Leaders act on performance. | Did review change decisions? HSE separating pedestrians and vehicles |
Check the route at busy arrival times and ask staff whether they can actually hold a conflicting delivery. HSE separating pedestrians and vehicles
What common weaknesses make policies ineffective?
Policies fail when they are generic, poorly communicated, out of date or disconnected from real arrangements.
Weak policies usually fail because they are too generic, poorly owned or disconnected from real arrangements. The table shows how those weaknesses appear and what a stronger approach would look like.
| Weakness | Why it matters | Better approach |
|---|---|---|
| Copied template | Does not reflect actual work or responsibilities. | Tailor to risk profile and roles. HSE prepare a health and safety policy |
| Responsibilities vague | People do not know what they own. | Name roles, duties and evidence. HSE prepare a health and safety policy |
| Arrangements missing | Intent is not translated into action. | Link to practical procedures and controls. HSE prepare a health and safety policy |
| Not shared | Workers cannot follow what they do not know. | Communicate and brief changes. HSE prepare a health and safety policy |
| No review trigger | Policy becomes stale after change. | Set review triggers and owners. HSE prepare a health and safety policy |
A policy that says “safety first” but leaves visitors in a reversing path has failed to assign effective control. HSE prepare a health and safety policy
Which duties apply in Great Britain and Northern Ireland?
Effective management duties apply in each jurisdiction; an ISO certificate or policy document does not replace control of the work.
Use the instrument for the site and workforce. Reporting a specified dangerous occurrence is distinct from recording an ordinary near miss; neither replaces checking the actual control. Management of Health and Safety at Work Regulations 1999 Management of Health and Safety at Work Regulations (NI) 2000 Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 2013 Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (NI) 1997
Both HSE and HSENI say a written health and safety policy is required when an employer has five or more employees; below that threshold a written policy can still help. The policy must be communicated and kept useful in the work. HSE prepare a health and safety policy HSENI health and safety policy
| Decision | Great Britain | Northern Ireland |
|---|---|---|
| General duties | GB Health and Safety at Work etc. Act 1974: protect employees and affected others. Instrument | NI Health and Safety at Work Order 1978: separate NI general-duty route. Instrument |
| Assessment and arrangements | GB Management Regulations 1999: assess risk and plan, organise, control, monitor and review. Instrument | NI Management Regulations 2000: separate NI assessment and arrangements route. Instrument |
| Recognised union representatives | GB Safety Representatives and Safety Committees Regulations 1977 where recognised-union representatives are appointed. Instrument | NI Safety Representatives and Safety Committees Regulations 1979 for the NI route. Instrument |
| Other employee consultation | GB Consultation with Employees Regulations 1996 where the union route does not cover workers. Instrument | NI Consultation with Employees Regulations 1996 for the NI route. Instrument |
| Specified reports | GB RIDDOR 2013 covers specified injuries, diseases and dangerous occurrences; ordinary near misses need internal learning. Instrument | NI RIDDOR 1997 is separate; ordinary near misses are not automatically reportable. Instrument |
How can the hierarchy of controls turn health and safety policy into effective risk controls?
ERICPD is used here as a planning mnemonic. The linked HSE five-level hierarchy is the official source for the order and relative reliability of controls; the two labels are not identical.
The document, dashboard or audit can assign and test a control; the hierarchy applies to the real hazard and people exposed.
Riverside Leisure Ltd receives deliveries beside a public entrance. A reversing vehicle can strike and crush a visitor. The policy must name the owner of the route, require pedestrian separation and empower staff to hold a delivery when the route is occupied; a signed statement alone is not a barrier. HSE separating pedestrians and vehicles
ERICPD is a six-stage planning aid. HSE’s five levels place elimination and substitution before engineering, administration and residual PPE. Isolate normally maps to engineered separation; ERICPD Control may be physical or administrative. Discipline sustains the selected control through maintenance, supervision and learning. HSE five-level hierarchy HSE five-level hierarchy
How should management verify controls for this task?
How should management verify controls for this task?
Read the complete visual as text
- For delivery vehicle reversing across a leisure-centre pedestrian entrance,…: For delivery vehicle reversing across a leisure-centre pedestrian entrance, the management check should start with a real control decision: Redesign access so deliveries drive through without reversing across the entrance. Name the person who will test it, keep evidence from the actual work, and reopen the assessment when the failure condition in the hierarchy table occurs. HSE management-system guidance .
- A review should compare the planned control with what…: A review should compare the planned control with what workers and supervisors can use in practice. Record the defect, owner, interim protection, verification and next review trigger so that a policy statement or certificate does not stand in for a working control.
For delivery vehicle reversing across a leisure-centre pedestrian entrance, the management check should start with a real control decision: Redesign access so deliveries drive through without reversing across the entrance. Name the person who will test it, keep evidence from the actual work, and reopen the assessment when the failure condition in the hierarchy table occurs. HSE management-system guidance.
A review should compare the planned control with what workers and supervisors can use in practice. Record the defect, owner, interim protection, verification and next review trigger so that a policy statement or certificate does not stand in for a working control.
How does this topic align with ISO 45001?
Use these examples to connect the relevant clauses to your own occupational health and safety management system. For each clause, identify the person responsible, the control in use and the evidence that it works.
Scroll across the table to read all four columns.
| ISO 45001 clause | How it applies | What to put in place | How to verify it works |
|---|---|---|---|
| 5.2 Health and safety policy | The policy sets the organisation’s commitments and gives managers a basis for setting health and safety objectives. | Have senior managers explain how they will provide safe, healthy work, meet applicable duties and other commitments, remove hazards, reduce risks, involve workers in decisions and keep improving. At Riverside, use those commitments to decide how to manage recurring faults and contractor work. | Compare the approved policy with recent resource decisions and ask staff on different shifts how it affects their work. |
| 5.3 Roles and responsibilities | Staff need to know who owns each part of the system and who can make an operational decision. | Name who can restrict use, seek competent advice and accept a return to service. Make deputy cover and handover responsibilities visible to reception and facilities staff. | Trace one defect from the first report to the person who accepted the verified repair. Check the same decision route with the night team. |
| 6.2.2 Plan how to achieve objectives | Planning gives a safety objective an owner, resources and a way to measure progress. | For a recurring door fault, assign a manager to address the cause, agree resources and define how the hotel will check whether the fault recurs. | Review the action plan alongside maintenance records and subsequent checks. Check whether the result supports closing the objective. |
Selected applications of ISO 45001:2018 with Amendment 1:2024. Use the current standard for a full assessment and check the legal duties that apply to the work and location.
ISO 45001:2018 · 2024 climate action amendment · ISO 45002 implementation guidance · ISO technical committee clause FAQ
How does this management decision transfer across sectors?
Transfer the decision method, not the assumed control: identify people, harm route, strongest feasible safeguard and hold point.
A policy, system or indicator becomes useful when the owner tests the actual barrier under the conditions of work. HSG65 Managing for health and safety HSE health and safety management systems
| Sector | Task and harm route | Physical decision and stop point |
|---|---|---|
| Construction | Concrete chasing exposes workers and other trades to respirable silica. | Policy names the project owner, no-chase preference, extraction arrangement and failed-capture stop point. HSE concrete chasing and mortar raking |
| Fuel logistics | Tank overfill can release fuel and form an ignitable vapour cloud. | Policy names technical control ownership, transfer-release authority and bypass escalation. HSE Buncefield learning |
| Leisure | Reversing delivery vehicle crosses a public entrance. | Policy names the facilities owner, separated route arrangement and delivery hold authority. HSE separating pedestrians and vehicles |
How can readers practise this decision?
Use health and safety policy as a workplace case: identify the real task, the person who owns the control decision and the evidence that shows the control is working. State what would make work pause and who would authorise a safe restart.
Then trace each legal or medical claim to a direct source in Official links, checking whether it applies in Great Britain, Northern Ireland or both. Explain any uncertainty and the specialist advice needed rather than filling the gap with an assumed rule.
These are SHARE practice prompts, not an accredited syllabus or marking rule. For management-system context, see HSE management-system guidance.
What must each role demonstrate before acting?
Role awareness must be followed by a practical demonstration, an assessor and a reassessment trigger.
Use the live or simulated task to test the stop decision and control evidence. A briefing, certificate or dashboard does not release a failed physical safeguard. HSE separating pedestrians and vehicles HSE prepare a health and safety policy HSENI health and safety policy
| Role | Practical demonstration | Assessor and record | Reassess when |
|---|---|---|---|
| Worker or visitor-facing colleague | Know who owns the route and how to hold unsafe delivery. | Supervisor observes report and response. | Route or supplier change. HSE separating pedestrians and vehicles |
| Supervisor | Apply policy arrangement to live pedestrian conflict. | Manager checks a held/released delivery. | Occupied route or failed barrier. HSE separating pedestrians and vehicles |
| Facilities or logistics manager | Design separation and update practical arrangements. | Director signs route evidence and field check. | New vehicle or entrance layout. HSE separating pedestrians and vehicles |
| Policy owner or adviser | Translate duties into named responsibilities and consultation. | Competent peer checks document and worker feedback. | Change, incident or legal update. HSE prepare a health and safety policy |
| Senior leader | Sign policy, resource route fix and test effectiveness. | Board records decision and field challenge. | Repeat conflict or review trigger. HSENI health and safety policy |
What warning signs show the policy is not working?
Warning signs appear when the policy is known as a document but not used as a management tool.
Warning signs are included because failure usually appears before a serious event. Treat these points as prompts for inspection, audit, supervision and management review rather than as simple compliance statements.
| Warning sign | How harm can develop | Action |
|---|---|---|
| Policy is generic | Controls do not match actual risk. | Tailor arrangements to business activities. HSE prepare a health and safety policy |
| People cannot describe responsibilities | Gaps appear during incidents or audits. | Brief and assess role understanding. HSE prepare a health and safety policy |
| Objectives are vague | Improvement cannot be measured. | Create SMART risk-based objectives. HSE prepare a health and safety policy |
| Policy not reviewed after change | Arrangements fall behind reality. | Use change and incident triggers. HSE prepare a health and safety policy |
| No worker feedback | Controls may be impractical. | Consult and close feedback loop. HSE prepare a health and safety policy |
| Arrangements absent | Intent never reaches the work. | Link policy to procedures, registers and checks. HSE prepare a health and safety policy |
What do the acronyms and key terms mean?
Acronyms should be understood before they are used in assessments, briefings, audits or learning answers.
Acronyms can exclude newer readers if they are not explained. This section keeps the main terms available at the end of the page so the article stays readable while still supporting learners and audit users.
| Acronym | Meaning | Plain-English use |
|---|---|---|
| GNC | NEBOSH National General Certificate | SHARE study route for policy structure and practical application. |
| SMART | Specific, Measurable, Achievable, Relevant and Time-bound | A way of setting useful objectives. |
| PDCA | Plan, Do, Check, Act | Continuous management cycle. |
| HSE | Health and Safety Executive | Great Britain's health and safety regulator. |
| RAMS | Risk Assessment and Method Statement | Common workplace document connecting arrangements to task control. |

Unlock another resource
You have used this month’s two free downloads. Publish a post in your own words to unlock one more resource, or choose SHARE Individual for 10 downloads per month.
You decide whether to share. If you do, use the relevant platform disclosure tools and do not make claims you do not genuinely hold.