SHARE Knowledge Hub
What should you know about digging and safe excavation?
Digging is any work that breaks or removes ground by hand tool, vacuum excavation or mechanical plant, and it can quickly become high risk when buried services, unstable ground, plant movements, people in trenches, contaminated soil, dust or nearby structures are involved. A safe dig starts before the bucket or spade touches the ground: identify why excavation is needed, obtain service information, locate and mark underground services, choose the safest method, set exclusion zones, plan temporary support, control spoil and plant loading, brief the team and inspect the excavation before work starts and after events that may affect stability. The best sites treat digging as a controlled operation, not a casual groundworks task; they use HSG47-style planning, permit-to-dig controls, competent supervision, emergency arrangements and clear stop-work rules when drawings, ground conditions or exposed services do not match the plan.
Understanding What should you know about digging and safe excavation?
Digging is any work that breaks or removes ground by hand tool, vacuum excavation or mechanical plant, and it can quickly become high risk when buried services, unstable ground, plant movements, people in trenches, contaminated soil, dust or nearby structures are involved. A safe dig starts before the bucket or spade touches the ground: identify why excavation is needed, obtain service information, locate and mark underground services, choose the safest method, set exclusion zones, plan temporary support, control spoil and plant loading, brief the team and inspect the excavation before work starts and after events that may affect stability. The best sites treat digging as a controlled operation, not a casual groundworks task; they use HSG47-style planning, permit-to-dig controls, competent supervision, emergency arrangements and clear stop-work rules when drawings, ground conditions or exposed services do not match the plan.
Why this matters at work
The recurring causes of excavation incidents are predictable: starting before plans are complete; treating utility drawings as exact; using a locator without skill or trial holes; allowing mechanical digging to approach an unconfirmed service; entering an unsupported excavation because it looked stable; placing spoil or plant at the edge; missing the effect of rain or water; losing control during shift change; and assuming a permit or PPE can compensate for a weak physical barrier. Each failure has an upstream decision. Investigation and assurance should look for that decision rather than only the moment a bucket struck a cable or a face collapsed.
Reopening after an incident must be controlled. The responsible person should confirm service-owner advice, electrical/gas/pipeline status, structural or temporary-works condition, atmosphere or contamination controls, public protection, equipment condition, evidence preservation, revised method, re-briefing and any reporting duties. Capture both preventative and recovery actions in the close-out. A rushed restart can turn a minor damage event into a major incident or repeat the same failure elsewhere.
How organisations manage this in practice
Monitor both performance and learning. Review service strikes and near misses, permit defects, inspection findings, water events, changes in ground condition, temporary-works deviations, public-interface failures, plant-pedestrian conflict, repeat findings and worker reports. Seek evidence on site rather than accepting a desk-based assurance alone: see the marked route, location record, trial holes, condition of the face, access route, spoil position and edge barrier. Escalate recurring controls failure to senior governance, design review or service-owner liaison rather than treating it as a supervisor-only issue.
Implement excavation control as a lifecycle: scope and design; utility and ground information; risk assessment; selection of elimination/reduction options; temporary-works and traffic design; permit and briefing; site setup; safe execution; inspection and change control; emergency readiness; backfill/reinstatement; and learning. Assign a named owner for each stage and avoid gaps between client, principal contractor, contractor, utility owner, designer and operational site manager. Update the construction phase plan or local equivalent as conditions and interfaces develop.
Handovers are a common loss of control. At shift change, contractor change, weekend closure or emergency interruption, communicate the excavation condition, exposed services, support, water, access, barriers, plant status, permits, open actions and reinspection needs. The incoming supervisor must make their own check; a signature cannot replace observation. Secure permits at suspension and cancel or close them only when the excavation is backfilled, protected or otherwise formally made safe, required service-owner conditions are met and no further disturbance is planned.

Excavations: see the ground, support and people
Follow a groundworker from planning the excavation to leaving it safely. Compare three ways of dealing with the sides, trace the route in and out, then decide what to do when a machine approaches the edge or water enters.
Checksheets and risk assessments
Equipment checksheets
- Excavations and trench access — 3D checks · Word · PDF
- Excavators and backhoe loaders — 3D checks · Word · PDF
Risk assessment forms
Risk assessment examples
Full written walkthrough — all 13 steps
1. Decide whether anyone needs to enter
What is happening: The cutaway reveals the space a groundworker may occupy and the material surrounding it. The empty excavation is a learning view, not permission to enter.
How harm can occur: Ground movement can bury or crush someone and prevent their escape. People outside can fall into the opening.
Best practice to apply: Consider avoiding entry or using a different method. Establish the design, work sequence, people affected and responsible supervision.
2. Check the ground and neighbouring structures
What is happening: The exposed layers help you see why conditions may change through the ground. Colour does not classify the soil or prove stability.
How harm can occur: Fissures, disturbed ground or undermined foundations can release material or destabilise adjacent structures.
Best practice to apply: Use appropriate site investigation and competent design/review. Check surrounding buildings and services; do not infer stability from a dry-looking face.
3. Locate services before breaking ground
What is happening: The planning station represents records, locating and safe exposure of services. It does not show surveyed service positions.
How harm can occur: A service strike may cause electrocution, burns, fire, explosion or flooding, affecting the operator and nearby people.
Best practice to apply: Plan and verify the actual service locations and precautions. Use the topic’s HSG47 guidance and resolve uncertainty before digging.
4. Trench box — stay inside the shield
What is happening: Look between the two steel panels. The green floor marks the shielded footprint; the spreaders hold the panels apart. The open ends are outside that protection.
How harm can occur: Ground can still move outside the box. A worker reaching past an end or standing between a panel and the trench face can be buried or trapped.
Best practice to apply: Check the specified box, its position, end protection and how workers reach it. Follow the designed sequence for installation, movement and removal. Keep people clear during movement.
5. Shoring — follow the ground load
What is happening: The sheeting bears against the trench faces. Follow the arrows from the ground into the sheets, along the horizontal walers and across the struts to the opposite side.
How harm can occur: A gap behind the sheeting, a displaced waler or a damaged strut can interrupt this load path and allow ground movement.
Best practice to apply: Check the support against the temporary works design and installation sequence. Report a displaced member from a safe position; never remove a brace to make space for access.
6. Battered sides — look at the whole slope
What is happening: Compare the wider opening with the box. Ground has been cut back to form a sloping face, reducing the mass that can fall into the work area. There are no box panels in this example.
How harm can occur: Water, loose layers and loads at the crest can make a previously stable face slip. The end faces also need assessment.
Best practice to apply: A competent person determines the profile for the ground and changing conditions. Allow room for the full batter and protect its crest. Never copy an angle from the model.
7. Compare a stepped cut with a continuous batter
What is happening: The same cross-section now has benches. Notice the short faces and ledges instead of one continuous slope.
How harm can occur: An individual face or the whole cut can fail. A ledge can collect loose material that then falls onto people.
Best practice to apply: Use benches only where specified for the actual ground. Choose a separate access route; the ledges are not a staircase.
8. Enter through the protected landing
What is happening: Follow the green arrows from the approach, through the guarded landing and down the secured ladder. Both feet of the ladder rest on the firm base inside the box, between the spreaders.
How harm can occur: Stepping over the side panel, climbing a brace or landing beyond the box exposes a person to a fall or collapse.
Best practice to apply: Use stairs or another suitable means where the task calls for it. When a ladder is appropriate, secure it on a firm, level base. Extend it at least 1 m above the landing unless another suitable handhold is provided. Face the ladder and keep a secure grip.
9. Trace the escape route back to the surface
What is happening: The arrows reverse. Trace the route along the protected floor to the foot of the ladder, up to the handholds, and back onto the clear surface approach.
How harm can occur: Spoil, hoses or a delivery across either landing can cut off the way out. A clear opening viewed from above tells you little about conditions at the foot.
Best practice to apply: Check both landings before entry. Keep tools off the ladder and arrange to move loads separately. Plan how to raise the alarm and recover an injured person; the ladder alone is not a rescue plan.
10. Keep plant and spoil outside the planned limit
What is happening: Find the excavator behind the marked plant limit and the separate spoil heap. Even a stationary machine adds load to the ground beneath its tracks.
How harm can occur: Extra weight can overload the side or its supporting system. Falling spoil, a slewing bucket or a reversing machine can strike people.
Best practice to apply: Agree the plant route, exclusion zone and spoil location against ground conditions, plant loads and the design. Use suitable barriers or stop blocks where required. The illustrated line gives no safe distance.
11. Plant crosses the limit — stop the movement
What is happening: The same excavator is now between the marker and the trench. Red arrows show extra load beneath the near track. A crack at the crest illustrates one possible warning.
How harm can occur: The edge can give way under the tracks, the machine can overturn, or soil can move towards the trench. Failure can occur before a crack is visible.
Best practice to apply: Stop plant movement, warn others and withdraw from the affected area by the safe route if available. Keep people away. Have the competent team agree safe recovery and reassess the excavation before anyone returns.
12. Water enters — withdraw and reassess
What is happening: Blue streaks show water seeping through the rear face near the end of the box. The blue pool reaches the trench floor and the ladder foot. The red sign marks the hold on entry.
How harm can occur: Flow can wash out fine material, weaken the face and undermine the foot of the ladder. A box does not keep out water or protect the open ends.
Best practice to apply: Stop affected work, raise the alarm and use a safe exit if available. If it is cut off, use the emergency plan. Keep others out. Review inflow, support, drainage and discharge together; uncontrolled pumping can make the ground less stable.
13. Who can release the excavation for work?
What is happening: The route remains on hold while the competent inspector checks the actual excavation. This last scene is a decision point: a clear floor after pumping is insufficient evidence to restart.
How harm can occur: An unseen void, damaged support or undermined landing can remain after water recedes or the machine has moved.
Best practice to apply: Inspect at the start of each shift and again after an event likely to affect stability or a fall of material. Record the findings as required, correct defects, check access and brief the team. Resume only once the competent inspection confirms safe conditions.
Illustrative awareness learning. The model does not design equipment, authorise work, verify safe conditions or complete a real inspection.
The wider workplace has its own account and subscription access. Exploring this lesson does not grant access, record course completion or authorise work.
UK guidance for further reading
HSE: excavation safetyHSE HSG47: avoiding danger from underground services
Excavators: slew, attachment and stored-energy harm pathways
Explore how this equipment can harm its users and other people, then follow the practical measures that interrupt each pathway. This is a hazards and good-practice lesson; the separate checklist remains the pre-use/safety-check activity.
Hazards and good practice: learn what can hurt people during use, change and maintenance. Pre-use and safety checks stay in the separate checklist.
Checksheets and risk assessments
Equipment checksheets
- Large tracked excavators — 3D checks · Word · PDF
- Excavators and backhoe loaders — 3D checks · Word · PDF
- Excavations and trench access — 3D checks · Word · PDF
Risk assessment forms
- Excavation, ground and service-strike assessment · Word
- Vehicle-pedestrian and public-interface assessment · Word
Risk assessment examples
Full written walkthrough — all 8 steps
1. Plan the machine and work envelope
What is happening: The full-size tracked machine shows a body, boom, arm and working attachment with different movement routes.
How harm can occur: The body or attachment can strike, crush or trap someone against ground or structures.
Best practice to apply: Choose equipment and a method suitable for the actual ground, excavation, space and people affected.
Why this works: A suitable plan removes the need for people to work inside an uncontrolled envelope.
Mobile plant and vehicles · What makes mobile work equipment hazardous?2. See the counterweight and slew interface
What is happening: The counterweight may move into a different space from the bucket.
How harm can occur: A pedestrian or worker behind the machine can be crushed against a fixed object.
Best practice to apply: Provide physical separation and sufficient planned working space and coordination; do not rely only on the operator seeing everyone.
Why this works: Separation addresses the hidden person as well as the visible digging point.
Mobile plant and vehicles · Practise the checks in 3D3. Trace the attachment-to-person route
What is happening: The bucket, coupler and pins transfer force and retain a heavy attachment.
How harm can occur: A detached or unexpectedly moving attachment can strike or crush a worker.
Best practice to apply: Use the specified compatible attachment and connection arrangements and keep people clear of the load/working route.
Why this works: Attachment retention and people separation act on different parts of the same failure chain.
Mobile plant and vehicles · Documents to download4. Resolve services and excavation loading
What is happening: Machine position and digging interact with services, trench edges and buried structures.
How harm can occur: A strike can release electricity, gas or water; machine loading can contribute to edge collapse.
Best practice to apply: Verify the actual service precautions and ground/support design, including plant position and changing loads.
Why this works: The machine's stability and the excavation's stability cannot be assessed independently.
Excavation safety and field controls · How should buried services be managed during excavation?5. Control travel and the driver's view
What is happening: Cab glazing and mirrors support a view but do not remove obscured areas.
How harm can occur: Travel, reversing or a changed position can bring the machine into contact with people or other plant.
Best practice to apply: Use suitable segregated routes and coordinated movements; stop when the required view or communication is lost.
Why this works: A visibility aid supports the work system; it does not replace segregation.
Mobile plant and vehicles · How can the ISO 45001 hierarchy of controls prevent mobile-plant collisions and pedestrian injuries?6. Treat lifting as a separate operation
What is happening: Using an excavator to lift is different from an ordinary digging cycle. This digging-bucket illustration does not identify or approve a rated lifting point.
How harm can occur: An unsuitable configuration or attachment can overload the machine or drop the load.
Best practice to apply: Where lifting is proposed, use equipment configured for it and a competent task-specific lifting plan and controls.
Why this works: A digging capability does not establish lifting capacity or approve a suspended-load operation.
Mobile plant and vehicles · Documents to download7. Control gravity and hydraulic energy for access
What is happening: The boom, attachment and pressurised connections can retain energy after the engine stops.
How harm can occur: A descending component or hydraulic release can crush or injure a maintainer.
Best practice to apply: Use the actual competent parking, isolation, pressure-release and support arrangements before intrusive work.
Why this works: Removing power alone does not support a raised component or remove trapped pressure.
Mobile plant and vehicles · What evidence shows the controls work in practice?8. Keep the method valid during change
What is happening: New ground, weather, services, loads or nearby trades change the operation.
How harm can occur: A previously workable arrangement may create a new collapse, collision or exposure route.
Best practice to apply: Stop the affected movement, reassess with responsible people and communicate the revised safe method.
Why this works: A check at the start cannot authorise all later changes in a dynamic workface.
Mobile plant and vehicles · How should a changing construction site manage a dumper?
Illustrative awareness learning. Geometry, colours and movement do not establish safe distances, capacity, exposure, isolation or work permission. Use the actual assessment, equipment information and competent arrangements.
The wider workplace has its own account and subscription access. Exploring this lesson does not grant access, record course completion or authorise work.
UK guidance for further reading
HSE: ExcavatorsResolve uncertainty before the excavation starts
Bring service information, competent locating, safe digging, stability and inspection into one pre-start decision. Neither a drawing nor a detector result alone establishes that the proposed excavation is safe.
The drawing conflicts with the site
Illustrative example. A marked service route differs from a feature found during the pre-start survey.
Decision. Hold the affected work, resolve the discrepancy through the competent safe-digging process and revise the method.
Evidence to check. Current service information, locating findings, ground and water conditions and the approved excavation approach.
Hold or escalation point. No bucket movement or entry while service or stability uncertainty remains.
Follow-up. Reassess after changed ground or water conditions and communicate the renewed release decision.
Resolve the service evidence before ground disturbance
Plans, locating and controlled trial exposure are different evidence layers. A conflict between them remains unresolved until competent assessment deals with it.

Resolve service uncertainty before ground disturbance

Full written explanation
Utility-repair example: the plan, locating information and actual service identity are different evidence layers.
- Compare starting information. Review relevant service plans, owner information, site history and recent changes. Keep uncertainty visible.
- Locate and identify competently. Use suitable locating and identification arrangements. A mark or instrument result alone is not confirmed service identity.
- Resolve evidence conflicts. Use the approved competent investigation method. Hold affected work while service evidence remains unknown or conflicting.
Change the pathway
- A drawing is not a survey. The paper prop provides no service depth, identity or accuracy claim.
- The tool is not a pass. A pictured locator cannot establish its suitability, result or operator competence.
- Ground controls remain separate. Assess actual ground, support, access and plant interfaces before reliance.
Evidence check: Use HSG47 and the actual competent method, service-owner information and excavation assessment. No safe digging depth, universal clearance or support design is supplied.
Planning, locating/identifying, controlled investigation and separate ground controls
Primary references: HSE: avoiding danger from underground services, HSG47 (GB) · HSE: excavation planning, support and inspection (GB)
Open the complete HD image (new tab)Download image
Planning, locating/identifying, controlled investigation and separate ground controls
Primary references: HSE: avoiding danger from underground services, HSG47 (GB) · HSE: excavation planning, support and inspection (GB)

Starting information
Obtain and compare relevant plans and service-owner information, including uncertainty and recent change.
Locate and identify
Use suitable competent locating and identification arrangements; a mark or detection result is not the same as confirmed identity.
Resolve and release
Use the approved method for controlled exposure and verify ground/support/access conditions. Hold conflicting or unknown service evidence.
The sketch is not a utility survey and supplies no safe digging depth or clearance.
What key facts should people know first about digging?
The first rule is simple: no digging should start until services, ground conditions, collapse risk and work method have been properly controlled.
Digging is deceptively familiar. A small trench, trial hole or post hole can strike a cable, fracture a gas service, undermine a wall, trap a worker, expose contaminated soil or create a fall hazard. The risk is not measured only by depth; it is measured by what is in the ground, what is next to the dig, who is exposed and what could change while the work is open.
HSG47 gives the core buried-services sequence: plan the work, locate and identify services, then excavate safely. Excavation safety adds a second sequence: decide how ground will be supported or battered, keep people and plant away from edges, provide safe access, inspect before entry and stop if stability or services are uncertain.
Mechanical digging is efficient but unforgiving. Hand digging is slower but gives more control near services. Vacuum excavation can reduce strike risk in some situations, but it still needs planning, competent operation, spoil/waste control and confirmation that the method suits the ground and service type.
| Key fact | Why it matters |
|---|---|
| Plans are not enough | Service drawings may be incomplete, inaccurate or unclear; they must be supported by locating and safe excavation. |
| Ground can collapse | No ground can be assumed to stand unsupported in all circumstances. |
| Spoil and plant load edges | Excavators, vehicles and spoil heaps can increase collapse risk if placed too close to the edge. |
| Services can kill | Electricity, gas, fuel, water, telecoms and process lines create direct and indirect risks if damaged. |
| Inspections are live controls | Excavations need competent inspection at required times, not just before the first day. |
| Stop-work rules matter | If the ground, drawings, services or weather change, the dig must be paused and reassessed. |
What does safe digging mean?
Safe digging means controlling the ground, services, plant, people and environment before and during excavation.
Safe digging covers hand digging, mechanical excavation, vacuum excavation, trenching, trial holes, utility exposure, foundation excavation, drainage runs, landscaping, fencing, road works and emergency repairs. It may be a short task, but it often sits inside a wider system: design, pre-construction information, utility searches, temporary works, permits, plant movement, traffic management and emergency response.
The safest question is not 'how quickly can we dig this?' but 'what could be hit, collapse, fall, flood, contaminate, ignite, electrocute, expose or trap someone?' A good method statement answers those questions in plain language and is briefed to the people doing the work.
Safe digging also means choosing the method honestly. A large excavator is not suitable for delicate final exposure near services. A spade is not suitable if the sides will collapse and bury the person using it. A permit is not suitable if it simply authorises work without checking the physical controls.
| Term | Meaning | Practical point |
|---|---|---|
| Digging | Breaking or removing ground by hand, machine or other method. | Can expose services, unstable ground, contamination or structural risk. |
| Excavation | The hole, trench, pit or opening created by digging. | Needs edge protection, support/battering, access and inspection where relevant. |
| Trial hole | A controlled small excavation used to confirm services or ground conditions. | Usually done carefully by hand or low-damage method near services. |
| Permit to dig | A controlled authorisation confirming checks, limits and controls. | Should be issued at the workface with service information available. |
| Temporary works | Temporary support or protection needed for excavation or adjacent structures. | Requires competent design, checking, installation and inspection. |
How should digging be planned before work starts?
Planning should define the scope, location, services, ground conditions, method, people, plant, controls and emergency response.
Planning begins with why the excavation is needed and whether it can be avoided. Trenchless methods, design changes, alternative routes, reduced depth or prefabrication may remove or reduce the need to dig. Where digging remains necessary, the planner should obtain utility drawings, site history, surveys, ground information and constraints before setting the method.
The plan should define the exact dig area, depth, width, sequence, access, spoil location, plant routes, exclusion zones, support system, inspections, weather triggers, pumping/dewatering, nearby structures and service avoidance controls. It should also identify who has authority to stop work.
Good planning is visible on site. The people digging should have drawings, markings, briefings, permits, locating results and clear instructions at the workface, not buried in a folder in the office.
For this decision, check HSE - Excavations, HSE - Avoiding danger from underground services HSG47 and NI CDM 2016 regulation 21 — excavations for the applicable work and location.
| Planning area | What to confirm | Evidence |
|---|---|---|
| Scope and design | Why the dig is needed, exact location and whether excavation can be avoided or reduced. | Design review, drawings and method option record. Source: HSE - Excavations. |
| Service information | Utility plans, private services, process lines, drainage, lighting feeds and redundant services. | Search results, site records and asset-owner responses. Source: HSE - Excavations. |
| Ground conditions | Soil type, made ground, water, contamination, buried structures and previous excavations. | Site investigation, surveys and local knowledge. Source: HSE - Excavations. |
| Temporary works | Support, shoring, battering, trench boxes, working platforms and nearby structures. | Temporary works design, check and permit to load/use if needed. Source: HSE - Excavations. |
| Plant and people | Excavator type, banksman, segregated routes, lifting plans and operator competence. | RAMS, lift plan where relevant and training evidence. Source: HSE - Excavations. |
| Emergency response | Gas strike, cable strike, collapse, flood, rescue, first aid and contact numbers. | Emergency plan, briefing and drill evidence where appropriate. Source: HSE - Excavations. |
How should buried services be controlled during digging?
Buried services should be managed through planning, locating, marking, controlled exposure and safe digging practice.
Underground services are one of the main reasons that digging becomes high risk. Electricity cables can arc, explode and burn. Gas releases can ignite or explode. Water mains can flood excavations or undermine ground. Telecoms and fibre strikes can disrupt critical services. Private supplies, temporary site feeds, irrigation, lighting, old drainage and redundant-looking pipes can all create traps.
HSG47's practical sequence is the backbone: obtain and review plans, survey the site, use suitable locating devices operated by competent people, mark service routes clearly, dig trial holes carefully, expose services before mechanical work gets close, and keep drawings updated when new information is found.
Mechanical excavation should be kept away from exposed or suspected services according to the service type, asset-owner requirements and method statement. For gas mains and services, HSE's pipeline FAQ highlights the need for safe digging practices and states that mechanical excavators should not be used within 500 mm of a gas pipe. Other services may need different distances and precautions, so the controlling document must be specific. See HSE pipelines and gas-supply FAQs for this gas-specific statement; use asset-owner instructions for the actual pipe.
For this decision, check HSE - Avoiding danger from underground services HSG47, HSE - Underground cables and HSENI example excavation method statement for the applicable work and location.
For the GB electrical-cable example, HSE underground-cables guidance explains that plans only indicate likely services, trained people must use suitable locating equipment, and locating needs to be repeated as the work progresses. Suitable trial holes help confirm the cable route; a detector pass does not prove every service absent or make mechanical digging safe. If field findings disagree with the plan, pause the affected dig and resolve the service location and method with competent people. The cable guidance supports the cable examples in the sequence table; other utilities, methods and NI legal duties require their own applicable assessment and sources. The table’s vacuum-exposure option is illustrative: this cable guidance describes suitable hand tools and does not specifically authorise vacuum excavation. Select any vacuum method through its own competent assessment and service-specific precautions.
| Stage | What good looks like | Failure to avoid |
|---|---|---|
| Plan | Obtain utility plans and identify public, private, temporary and redundant services. | Assuming absence of plans means absence of services. Source: HSE underground cables (GB cable example). |
| Locate | Use suitable CAT and Genny or other detection method by competent people. | Treating a scan as proof when conditions or device limits are unclear. Source: HSE underground cables (GB cable example). |
| Mark | Mark services on the ground and protect markings from being lost. | Allowing rain, traffic or spoil to remove markings. Source: HSE underground cables (GB cable example). |
| Expose | Use controlled trial holes and careful hand/vacuum methods near services. | Letting a machine bucket chase the service line. Source: HSE underground cables (GB cable example). |
| Control | Set machine exclusion limits, supervision, permit conditions and stop-work triggers. | Continuing when drawings and findings do not match. Source: HSE - Excavations. |
| Update | Record unexpected services and update drawings or local records. | Leaving the next team to rediscover the same hazard. Source: HSE - Excavations. |
When should mechanical, hand or vacuum digging be used?
The digging method should match the risk, ground conditions, service proximity, precision needed and exposure of people.
Mechanical digging is useful for bulk excavation, reduced manual effort and productivity, but it creates high-energy contact with services and people. Hand digging gives more feel and control near services, but it increases manual handling, hand-arm strain, slips, struck-by and collapse exposure. Vacuum excavation can reduce direct tool contact with services but can introduce suction, spoil, noise, waste and traffic management issues.
The safest method may change during the task. A machine may open the top layer, then hand or vacuum methods expose a service, then the machine continues only once a safe zone is confirmed. That changeover should be planned, supervised and briefed rather than improvised.
Tools matter. Insulated tools may be needed near electrical hazards, but they are not permission to strike cables. Picks, forks, breakers and sharp spades are generally higher strike-risk tools near services. Blunt or damaged tools increase force and injury risk.
For this decision, check HSE - Avoiding danger from underground services HSG47 and HSENI example excavation method statement for the applicable work and location.
| Method | Best use | Key controls |
|---|---|---|
| Mechanical excavator | Bulk excavation away from known services and people. | Trained operator, banksman where needed, exclusion zones, service limits and edge loading controls. Source: HSE - Excavations. |
| Hand digging | Final exposure and careful work near suspected or known services. | Suitable tools, clear service markings, manual handling controls and safe trench conditions. Source: HSE - Excavations. |
| Vacuum excavation | Exposing services or reducing strike risk where suitable. | Competent operator, waste controls, service compatibility and traffic/pedestrian segregation. Source: HSE - Excavations. |
| Breaker or powered tool | Breaking hard surfaces before excavation. | Service clearance, HAVS/noise/dust controls, eye/face protection and exclusion zone. Source: HSE - Excavations. |
| Trenchless method | Reducing open excavation where feasible. | Design review, service location, launch/receive pit controls and ground movement assessment. Source: HSE - Excavations. |
How should service verification and controlled exposure shape a digging method?
Compare a planned trial hole with the wider excavation, then examine service support, plant separation, access and changed conditions. A suitable method depends on the service owner, ground, task and current evidence.

Trial holes and positive verification
A planned trial hole can reveal a service at a specific point. Record the finding and resolve unexpected position or identity before relying on it.
Learning focus: A planned trial hole can reveal a service at a specific point. Record the finding and resolve unexpected position or identity before relying on it.
Contextual workplace scene. Use the task, control and evidence checks in this section; appearance alone does not establish safe conditions, individual health or approval.

Safe exposure and excavation methods
Choose the method through the agreed plan, owner requirements and equipment limits. Hand tools and vacuum excavation both need controlled use.
Learning focus: Choose the method through the agreed plan, owner requirements and equipment limits. Hand tools and vacuum excavation both need controlled use.
Contextual workplace scene. Use the task, control and evidence checks in this section; appearance alone does not establish safe conditions, individual health or approval.
Educational example, not to scale. Existing services may differ. This view is not a site survey, excavation design or permit to dig.
Controlled-exposure host; neither hand tools nor vacuum excavation are automatically safe for every service.
Return to the main excavation lesson · Explore the planned Build Out excavation controls
How should trench collapse and ground instability be prevented?
Excavation collapse should be prevented by design, support, battering, shielding, edge control and competent inspection.
A trench does not need to be deep to be dangerous. Soil can fail suddenly, especially in made ground, wet ground, granular material, previously disturbed ground or where plant, spoil, traffic or structures load the edge. HSE notes that a cubic metre of soil can weigh more than 1.5 tonnes, which explains why collapse injuries are often fatal.
Before digging a trench, pit or other excavation, decide what support or battering is needed. Options include trench boxes, trench sheets, hydraulic support, timbering, designed shoring, stepping, battering to a safe angle, exclusion from unsupported sections and temporary works design for complex situations. Support equipment must be available before people are exposed, not ordered after the trench is open.
Collapse controls also protect people outside the excavation. Nearby walls, scaffolds, pavements, roads, trees, foundations and services can be undermined. Water inflow, pumping and weather can change stability during the day.
For this decision, check HSE - Excavations, CDM 2015 regulation 22 - Excavations and NI CDM 2016 regulation 21 — excavations for the applicable work and location.
| Hazard | Control | Evidence |
|---|---|---|
| Side collapse | Shoring, trench box, battering, stepping or exclusion from unsupported ground. | Temporary works design and inspection record. Source: HSE - Excavations. |
| Spoil at edge | Keep spoil and materials set back from the excavation edge. | Site layout and supervisor check. Source: HSE - Excavations. |
| Plant loading | Keep excavators, dumpers and vehicles away from unsupported edges. | Traffic plan, barriers and observation. Source: HSE - Excavations. |
| Falling material | Use toe boards, trench sheets, box extensions or edge protection. | Inspection and physical check. Source: HSE - Excavations. |
| Water inflow | Plan dewatering and assess effect on stability. | Pump plan and ground assessment. Source: HSE - Excavations. |
| Undermined structures | Survey and support adjacent foundations, walls or services. | Engineer advice and temporary works record. Source: HSE - Excavations. |
How should plant, pedestrians and work areas be controlled around digging?
People should be separated from moving plant, slewing zones, falling spoil, open edges and reversing vehicles.
Digging rarely involves only the person holding the spade. Excavators slew, dumpers reverse, lorries deliver aggregate, pedestrians cross sites, service owners attend, surveyors mark routes and supervisors inspect. Poor separation is a common route to crush, struck-by and fall injuries.
Controls should define where plant travels, where pedestrians walk, who banks plant, where spoil goes, how loads are lifted, where barriers are placed, and who can enter the digging zone. Excavator buckets, quick hitches, lifting accessories and attachments must be suitable and maintained.
Communication must be agreed before work starts. Hand signals, radios, exclusion-zone rules and stop commands should be understood by operators and ground workers. Nobody should work within the excavator's operating radius without a deliberate, controlled system.
| Interface | Control | Evidence |
|---|---|---|
| Excavator slew radius | Set exclusion zone and use a banksman where needed. | Briefing and observation. Source: HSE - Excavations. |
| Reversing vehicles | One-way routes, segregation, reversing aids and trained banksmen. | Traffic management plan. Source: HSE - Excavations. |
| Spoil movement | Designated spoil areas away from edges and public routes. | Site layout and checks. Source: HSE - Excavations. |
| Lifting with excavators | Lift plan, rated equipment, suitable attachment and LOLER controls. | Lift plan and inspection records. Source: HSE - Excavations. |
| Public interface | Barriers, covers, lighting, signage and secure site boundary. | Public protection inspection. Source: HSE - Excavations. |
| Communication | Agreed signals, radios and stop-work command. | Toolbox talk and supervisor monitoring. Source: HSE - Excavations. |
What health risks can digging create?
Digging can expose workers to dust, contaminated soil, asbestos, lead, fumes, manual handling, noise, vibration and poor welfare.
Digging is often treated as a safety topic, but health risks can be just as important. Breaking concrete, cutting surfaces, dry digging and moving dusty spoil can expose workers to respirable crystalline silica and other construction dusts. Made ground, old industrial sites, demolition areas, fuel spills or buried waste can expose workers to contaminated soil, asbestos fragments, hydrocarbons, lead or biological hazards.
Powered breakers, compactors and hand tools can create hand-arm vibration, noise, musculoskeletal strain and flying debris. Petrol or diesel equipment in excavations can allow fumes to accumulate. Wet ground, poor welfare and contaminated PPE can create skin and hygiene risks.
The control plan should therefore include COSHH assessment, dust suppression, wet methods where suitable, respiratory protective equipment where needed, decontamination, welfare, waste classification, tool maintenance and health surveillance where the risk justifies it.
| Health risk | How it arises | Control |
|---|---|---|
| Construction dust and silica | Breaking concrete, cutting, dry sweeping or dusty spoil. | Wet suppression, on-tool extraction, segregation, RPE and cleaning controls. Source: HSE - Construction dust CIS36. |
| Contaminated soil | Made ground, old industrial sites, spills or buried waste. | Site investigation, COSHH, hygiene, PPE/RPE, waste controls and stop-work rules. Source: HSE - Construction dust CIS36. |
| Asbestos fragments | Demolition ground, old services, made ground or fly-tipped material. | Asbestos procedure, competent advice and licensed/non-licensed controls as applicable. Source: HSE - Construction dust CIS36. |
| Fumes in excavations | Engines, generators, compressors or contaminated ground vapours. | Keep engines out, ventilate, monitor atmosphere where needed and stop work. Source: HSE - Construction dust CIS36. |
| Manual handling | Hand digging, lifting spoil, using breakers or awkward posture. | Mechanical aids, task rotation, tool selection and workload planning. Source: HSE - Construction dust CIS36. |
| Noise and vibration | Breakers, compactors, excavators and powered tools. | Exposure assessment, low-vibration tools, maintenance, time limits and PPE. Source: HSE - Construction dust CIS36. |
What inspection and hand-back evidence is needed for excavations?
A competent person should inspect excavations before work and after events that could affect stability or safety.
Inspection is not paperwork after the fact. It is a live control that confirms whether the excavation is safe for people to work in or near. HSE guidance expects competent inspection of excavation supports or battering at the start of the working shift and at other specified times. Work should not continue until defects are corrected.
Triggers include the start of shift, after collapse or fall of material, after heavy rain, after flooding, after plant loading, after support alteration, after dewatering changes, after unexpected services are exposed and after any event that may affect strength or stability.
The hand-back should confirm the excavation has been made safe, services protected or reinstated, barriers removed only when safe, drawings updated where needed and ground reinstated to the required standard.
For this decision, check HSE - Excavations, CDM 2015 regulation 22 - Excavations and NI CDM 2016 regulation 21 — excavations for the applicable work and location.
| Inspection point | What to check | Record |
|---|---|---|
| Start of shift | Support, battering, edge protection, access, water, spoil, plant routes and services. | Excavation inspection record. Source: HSE - Excavations. |
| After weather | Rain, water inflow, erosion, softening, slippage and pumping effects. | Reinspection and corrective actions. Source: HSE - Excavations. |
| After change | Altered depth, support, plant position, service exposure or adjacent work. | Supervisor approval and method update. Source: HSE - Excavations. |
| Permit close | Scope complete, services protected, excavation safe and reinstatement controlled. | Permit hand-back and photos if useful. Source: HSE - Excavations. |
| Defects | Any condition that could give rise to risk. | Immediate stop, correction and reinspection before work resumes. Source: HSE - Excavations. |
How can the hierarchy of controls reduce risks while opening a service trench beside buried utilities?
Start by removing the hazard where practicable, then consider substitution, engineering controls and work-method controls. Use PPE for residual risk. These priorities follow HSE’s hierarchy of controls; the task-specific examples below must still be checked against the relevant HSE guidance and local conditions.
The hierarchy is powerful for digging because the best controls are often upstream. Avoiding the excavation, rerouting a service, using trenchless methods, designing shallower runs or providing pre-installed ducts can remove a major hazard before site work starts.
Where digging remains necessary, the focus moves to reducing exposure, isolating people from collapse and plant, controlling the method through permits and inspections, using PPE for residual hazards and maintaining discipline through supervision and stop-work authority.
On a utility renewal, the asset owner supplies and checks service information; on a landscaping job, the contractor still has to locate utilities and assess the ground. Both hold digging when the service identity or excavation stability is unresolved.
Which UK legal duties are relevant to digging and excavation?
The main duties come from CDM, general health and safety law, work equipment, lifting, COSHH and service-specific requirements. GB and Northern Ireland use separate instruments; do not carry a GB regulation number into an NI decision.
In Great Britain, CDM 2015 regulation 22 addresses excavations; in Northern Ireland, CDM 2016 regulation 21 is the excavation provision. Both require controls against collapse, falling material and people or plant falling in, with competent inspection where supports or battering are used. Use GB regulation 22 and NI regulation 21 for the exact work location.
Legal compliance should be visible in the plan, not just quoted in the method statement. Evidence includes pre-construction information, utility searches, permit-to-dig records, excavation inspections, temporary works design, plant inspections, competence records, COSHH controls and briefings.
| Duty or regulation | Why it matters | What good management should show |
|---|---|---|
| CDM 2015 regulation 22 - Excavations — GB instrument | Requires prevention of danger from excavations, collapse, dislodgement and falls. | Support/battering, edge protection, inspection and safe access. |
| CDM 2015 regulation 19 - Stability of structures — GB instrument | Relevant where digging could affect structures, temporary works or adjacent stability. | Temporary works design, engineer review and support arrangements. |
| Construction (Design and Management) Regulations 2015 — GB instrument | Sets project duties for clients, designers, principal contractors, contractors and workers. | Pre-construction information, construction phase plan, cooperation and supervision. |
| Health and Safety at Work etc. Act 1974 — GB instrument | Sets broad duties to protect employees and others. | Safe system, competent supervision and public protection. |
| Management of Health and Safety at Work Regulations 1999 — GB instrument | Requires risk assessment, competent assistance and preventive arrangements. | Suitable assessment, review after change and coordinated controls. |
| Provision and Use of Work Equipment Regulations 1998 — GB instrument | Applies to excavators, tools, breakers and locating equipment. | Suitable equipment, maintenance, inspection and training. |
| Lifting Operations and Lifting Equipment Regulations 1998 — GB instrument | Relevant where excavators lift loads or lifting accessories are used. | Lift plans, thorough examination and competent lifting arrangements. |
| Control of Substances Hazardous to Health Regulations 2002 — GB instrument | Applies to dust, fumes, contaminated soil and hazardous substances. | COSHH assessment, exposure controls, hygiene and RPE where needed. |
| NI CDM 2016 regulation 21 — excavations — NI instrument | Prevent collapse, falling material and people or plant falling in; inspect supported/battered excavations before shifts and after specified events. | Competent inspection, support and safe-start record. |
| NI CDM 2016 — project duties — NI instrument | Clients, designers and contractors coordinate safe construction work and pre-construction information. | Ground/service information, construction phase plan and coordination. |
| Health and Safety at Work (NI) Order 1978 — NI instrument | General duties to workers and others affected by digging. | Safe system, supervision and public boundary. |
| NI Management Regulations 2000 — NI instrument | Risk assessment, arrangements and competent assistance. | Assessment, named owner, review after change. |
| NI PUWER 1999 — NI instrument | Suitable and maintained excavators, breakers and locating equipment. | Equipment checks, training and isolation. |
| NI LOLER 1999 — NI instrument | Applies when lifting equipment and accessories are used for a lifting operation. | Lift plan and examination evidence where applicable. |
| NI COSHH 2003 — NI instrument | Controls excavation dust and contaminated-ground exposures. | Exposure assessment, engineering controls and RPE where needed. |
What should a digging risk register include?
The risk register should describe the credible digging events, barriers and evidence that proves controls are working.
| Event or issue | Risk route | Preventing controls | Response or mitigation | Evidence to check |
|---|---|---|---|---|
| Underground cable strike | Mechanical or hand tool contacts live cable. | Plans, CAT/Genny, marking, trial holes, exclusion distances and careful exposure. | Stop work, keep people away, contact network owner and emergency services if needed. | Utility plans, scan record, permit, briefing and investigation. Source: HSE - Excavations. |
| Gas main or service damage | Bucket or tool damages pipe or coating. | Asset-owner plans, locating, hand digging near service and gas-specific controls. | Evacuate/avoid ignition, contact gas emergency route and secure area. | HSG47 controls, permit and emergency briefing. Source: HSE - Excavations. |
| Trench collapse | Unsupported or loaded ground fails. | Temporary works, shoring, battering, edge set-back and inspection. | Rescue plan, emergency services, stop similar work and investigate. | Inspection record, support design and weather checks. Source: HSE - Excavations. |
| Person struck by plant | Groundworker enters excavator or vehicle danger zone. | Segregation, banksman, exclusion zone, traffic plan and communication. | First aid, isolate plant, review traffic management. | Briefing, observation and CCTV/photos where available. Source: HSE - Excavations. |
| Contaminated soil exposure | Unexpected asbestos, fuel, chemicals or biological contamination. | Site history, sampling, COSHH, hygiene, PPE/RPE and stop-work triggers. | Stop, isolate, competent assessment and waste controls. | Site investigation, COSHH and waste transfer records. Source: HSE - Excavations. |
What competence and training are needed for digging?
Competence should match the role: planners, supervisors, operators, groundworkers and inspectors need different levels of knowledge.
General induction is not enough for people who dig. Workers need to understand service markings, hand-digging methods, exclusion zones, spoil placement, collapse warning signs, dust and contamination controls, emergency actions and the right to stop work.
Supervisors need deeper competence because they issue or manage permits, brief teams, inspect excavations, coordinate plant and contractors, and decide when conditions have changed enough to stop work. Plant operators need equipment competence plus service-avoidance and people/plant interface awareness.
For complex excavations, temporary works competence is essential. A trench box used incorrectly, unsupported ground left open, or a support system altered without authority can be as dangerous as having no support.
| Role | Competence needed | Evidence |
|---|---|---|
| Groundworker | Safe hand digging, service awareness, edge controls, PPE/RPE, stop-work triggers and emergency action. | Training record and supervisor observation. Demonstration and assessment: Supervisor observes a real service-locating/hand-dig task and stop decision; record signed observation and briefing. Reassess after a service strike, changed ground/service information or missed control. Source: HSE - Avoiding danger from underground services HSG47. |
| Plant operator | Excavator competence, service exclusion limits, communication, lifting limits and people/plant segregation. | Authorisation, CPCS/NPORS or equivalent evidence and site briefing. Demonstration and assessment: Appointed supervisor checks a practical plant exclusion/spotter exercise and site authorisation before operation; retain assessment and authorisation. Reassess for changed plant, ground, buried services or unsafe operation. Source: HSE - Avoiding danger from underground services HSG47. |
| Supervisor | Permit to dig, HSG47 controls, excavation inspection, temporary works interface and emergency response. | Supervisor training and inspection competence evidence. Demonstration and assessment: Construction manager reviews a completed permit, service plan and excavation inspection on site; retain signed competence/appointment record. Reassess after a design, ground, sequence or legal change and any serious near miss. Source: HSE - Avoiding danger from underground services HSG47. |
| Temporary works coordinator/supervisor | Design, checking, installation, inspection and control of excavation support. | Formal appointment and competence evidence. Demonstration and assessment: Temporary works manager checks a design/installation/inspection handover against the appointed role; retain appointment, check and inspection records. Reassess after support-system or ground-condition change. Source: HSE - Avoiding danger from underground services HSG47. |
| HSE adviser/auditor | Can audit service avoidance, permits, inspections, plant interface and health controls. | Audit records and technical CPD. Demonstration and assessment: Technical lead reviews a sample excavation audit and the adviser’s corrective-action judgement; retain audit and review record. Reassess after method change, repeated findings or relevant guidance update. Source: HSE - Avoiding danger from underground services HSG47. |
How should the controls be managed and reviewed?
Assign owners to the significant risks, put the chosen controls into the work plan, check that they work in practice and change them when conditions or evidence change.
HSE describes this as a continuing plan, do, check and act process. For digging, record who checks the controls, what evidence shows they are working, and which failure stops the work or triggers review. A formal management system is a choice, not a substitute for the applicable legal duties. Read HSE management guidance.
What are the warning signs that digging is not being controlled?
Warning signs usually appear as weak planning, missing service evidence, unsupported excavations, plant interface problems or poor inspection.
Unsafe digging often has visible clues before the incident. Drawings are missing or old, service markings are vague, workers cannot explain the permit, the machine starts before trial holes are dug, spoil is piled at the edge, pedestrians walk through the work area, or nobody knows who inspected the trench.
These weaknesses can cause severe harm. A cable strike can burn or kill; a gas strike can explode; a trench collapse can bury a person; undermined structures can fall; contaminated soil can expose workers; and poor barriers can allow the public or workers to fall into open ground.
Supervisors should treat these signs as stop-work triggers, not coaching opportunities while the bucket is already in the ground.
| Warning sign | How harm can manifest | Immediate response |
|---|---|---|
| No current service information | Unexpected cable, gas, water or telecoms strike. | Stop and obtain/verify information before digging. Source: HSE - Excavations. |
| CAT scan not recorded or understood | False confidence and service strike. | Re-scan with competent person and brief findings. Source: HSE - Excavations. |
| Unsupported vertical sides | Collapse, burial or crush injury. | Stop entry and install support/batter/shield. Source: HSE - Excavations. |
| Spoil or plant at edge | Edge failure or material falling onto workers. | Move load back and reassess stability. Source: HSE - Excavations. |
| No barriers around open excavation | Falls by workers or public. | Install edge protection, covers, lighting and signage. Source: HSE - Excavations. |
| Water entering excavation | Ground instability, drowning or access failure. | Stop work, pump/control water and reinspect. Source: HSE - Excavations. |
| Unexpected odour, staining or material | Contaminated ground or hazardous atmosphere. | Stop, isolate and obtain competent assessment. Source: HSE - Excavations. |
What do the acronyms and key terms mean?
These acronyms are commonly used in safe digging, excavation and construction management.
| Acronym or term | Full expansion | Meaning in this topic |
|---|---|---|
| CAT | Cable avoidance tool | A locator used with plans and safe trial methods to identify buried cables; a clear reading is not proof that no service exists. |
| CDM | Construction (Design and Management) | The GB and NI construction duty frameworks; excavation is GB regulation 22 and NI regulation 21. |
| COSHH | Control of Substances Hazardous to Health | The GB or NI rules for assessing and controlling dust and contaminated-ground exposure. |
| DNO | Distribution network operator | An electricity network owner to contact about cable information and a strike response. |
| HSG | HSE guidance-series code | An HSE guidance-series code, such as HSG47 on underground services; guidance is not itself a statute. |
| LOLER | Lifting Operations and Lifting Equipment Regulations | GB or NI lifting rules when an excavator or lifting accessory is used for a lifting operation. |
| PUWER | Provision and Use of Work Equipment Regulations | GB or NI work-equipment rules for excavators, breakers and locating equipment. |
| RAMS | Risk assessment and method statement | The task-specific assessment and method that should match the actual ground and services. |
| RPE | Respiratory protective equipment | Respiratory protection for residual assessed dust exposure after stronger controls. |
| TWC | Temporary works coordinator | The named role coordinating temporary-works design, checks and release on a project. |
