SHARE Knowledge Hub

Hierarchy of Controls

The hierarchy of controls chooses stronger measures before personal protection or reminders. The five-level sequence is elimination, substitution, engineering controls, administrative controls and PPE. ERICPD is a useful planning prompt—Eliminate, Reduce, Isolate, Control, PPE, Discipline—but its “Isolate” usually maps to engineering and “Discipline” sustains controls rather than becoming an extra protective layer. Test each proposed measure on the actual task and verify it still works.

Updated 2026-11-11UK focus

Understanding Hierarchy of Controls

The hierarchy of controls is a decision aid for choosing how to prevent injury and ill health.

Why this matters at work

Harm mechanisms differ: airborne particles may damage lungs after repeated inhalation; a sensitiser can trigger occupational asthma; a liquid can cause irritant or allergic dermatitis by skin contact; a corrosive splash can injure eyes rapidly.

Start with a precise hazard and harm pathway. Identify the task, energy or agent, release or contact point, people exposed, foreseeable failures and potential injury or illness. Include nonroutine cleaning, maintenance, changeovers and contractors; HSE warns that those groups are easy to miss. Assess existing controls by observing the work and talking to workers, not merely reading a procedure. A machine may be guarded during production yet open for frequent unplanned clearing; a solvent may be enclosed during mixing but manually decanted for samples.

How organisations manage this in practice

Multiple measures are useful only if their failure modes differ. A guard plus an interlock plus safe isolation for maintenance addresses several pathways; three versions of the same verbal warning do not. Inspect common-cause failures such as power loss, poor housekeeping, schedule pressure or one supervisor controlling every approval. Record what reveals a failed barrier and who acts. Trend test results, incidents and worker reports. The strongest design is one that remains usable on a bad day, not merely during a demonstration.

An interlocked guard prevents access to dangerous motion in normal operation; it does not eliminate the energy or protect during defeated-guard maintenance. A scaffold guardrail is collective fall prevention; a fall-arrest harness is personal mitigation and needs rescue. An approved respirator reduces the wearer's inhalation, but does not stop dust spreading to unprotected colleagues. This precision prevents a low-cost model from mistaking a label for a functioning control.

State performance requirements: a guard prevents access during motion; extraction captures the relevant contaminant; a delivery route avoids pedestrians; a permit stops simultaneous incompatible work. Assign a competent owner, installation and maintenance steps, inspection or test, training, failure response and review trigger. Check the completed work with users. A control with no clear verification method is not necessarily ineffective, but the organisation cannot credibly claim assurance. Close the loop after a near miss, symptom report, change or routine monitoring finding.

What are the key facts about the hierarchy of controls?

The key facts are that risk control starts with prevention, not paperwork, and that the strongest controls are usually designed into the work.

Start at the top

Always ask whether the hazard can be eliminated before discussing PPE.

Physical controls are more reliable

Guards, enclosure, extraction, interlocks and distance normally outperform reminders and signs.

Administrative controls are still important

Permits, procedures, training and supervision organise work, but they can degrade under pressure.

PPE is a last line, not a complete system

PPE can be essential but should not be the only control for significant risk where stronger options exist.

Evidence matters

A completed risk assessment is weak unless it shows what controls were considered, selected, implemented and checked.

How can the hierarchy of controls guide stronger workplace risk reduction in practice?

It means choosing controls in a deliberate order so the job becomes safer by design rather than relying mainly on people being careful.

In plain English, the hierarchy asks: can we avoid doing the dangerous thing, do it in a safer way, separate people from the danger, control the danger at source, protect people from what remains and then set clear rules so the system is maintained? HSE five-level hierarchy

This is why it is useful for both beginners and experienced professionals. A new supervisor can use it to challenge a weak risk assessment. A senior engineer can use it to justify a design change. A process safety manager can use it to show how a major accident barrier prevents, detects, controls or mitigates escalation.

How should the selected controls be checked in practice?

ERICPD is used here as a planning mnemonic. The linked HSE five-level hierarchy is the official source for the order and relative reliability of controls; the two labels are not identical.

ERICPD should be used as a thinking route, not a decorative heading in a risk assessment.

ERICPD is a mnemonic for planning and maintaining controls, not an alternative legal ranking. Reduce may involve substitution or lower exposure; Isolate generally uses engineering; Control can include engineering or administration; Discipline sustains the chosen controls. The five-level hierarchy explicitly separates substitution from elimination. HSE five-level hierarchy HSE five-level hierarchy HSE five-level hierarchy

A weak assessment lists one control under each heading even when the control is not realistic. A strong assessment shows which higher-order options were considered, which were selected, why some were not reasonably practicable and how the final control package will be verified.

For example, a silica cutting task should not jump straight to FFP3 masks. It should first ask whether cutting can be avoided, whether pre-cut material can be bought, whether the cut can be done off site, whether wet cutting or on-tool extraction is available, and only then what RPE and supervision remain necessary.

Which hazard routes need additional control checks?

Use elimination, substitution, engineering, administration and PPE as the five-level decision order. Do not rank isolation above all engineering controls or merge personal discipline into PPE.

The silica-cutting example shows each step, owner, test and failure point. Prefabrication can remove on-site cutting; if cutting remains, verify water suppression or on-tool extraction at the blade before relying on RPE. HSE construction silica control sheets HSE five-level hierarchy

What does a good control decision look like?

A good control decision is proportionate, evidence-based and linked to the risk register, task and people who will do the work.

The best control decision is usually made before work starts: during design, procurement, planning or method selection. Once people are already on site, options narrow and the system often leans on temporary controls. This is why early planning matters so much. HSE five-level hierarchy

A good decision explains the residual risk honestly. If the chosen control depends on worker behaviour, supervision or maintenance, the assessment should say how that dependency will be managed and checked.

TestQuestion to askGood answer
EffectivenessWill this control actually reduce the risk?Yes, because it removes the exposure route or prevents contact. HSE five-level hierarchy
ReliabilityWill it still work during busy, wet, noisy or abnormal conditions?Yes, because it is engineered, inspected and has a backup. HSE five-level hierarchy
UsabilityCan workers use it without fighting the job?Yes, because workers helped test it and the task still flows. HSE five-level hierarchy
MaintenanceWho keeps it working?Owner, inspection frequency and defect route are defined. HSE five-level hierarchy
EvidenceHow will we know it is used?Checklist, observation, monitoring, audit or maintenance record. HSE five-level hierarchy

How does the hierarchy apply to common workplace hazards?

The hierarchy becomes useful when it is applied to real hazards rather than discussed as a theory diagram.

The examples below show how the same logic works across very different topics. The important skill is to stop and ask whether a stronger control is available before accepting the familiar control. Often the better answer is hidden in design, sequencing, procurement or maintenance. HSE five-level hierarchy

For learners, a strong exam answer usually moves from higher-order controls to lower-order controls and explains the practical reason for the order.

HazardHigher-order approachLower-order support
Work at heightBuild at ground level, use permanent edge protection or MEWP access.Harness rescue plan, training and pre-use checks. HSE five-level hierarchy
Hazardous substanceSubstitute product, enclose process and capture contaminant at source.Gloves, RPE, hygiene and health surveillance. HSE five-level hierarchy
Machinery hazardGuard and interlock dangerous parts; design out access to moving parts.Isolation procedure, supervision and maintenance training. HSE five-level hierarchy
Manual handlingEliminate lift, use mechanical aid or redesign load and layout.Team lift instruction and handling training. HSE five-level hierarchy
NoiseBuy quieter equipment, isolate source and enclose plant.Hearing protection zones and audiometry. HSE five-level hierarchy
Process safetyReduce inventory, design containment and add independent protection layers.Procedures, permits, shift handover and emergency drills. HSE five-level hierarchy

Why should workers be involved in choosing controls?

Workers know how the job is really done, so they can identify controls that will fail before an incident proves it.

A control that looks good in a meeting can fail on the floor because it slows the job, blocks visibility, clashes with other PPE, creates a manual handling problem or cannot be used in rain. Worker involvement helps test the control against reality. HSE managing risks and risk assessment

This is not about asking workers to accept risk. It is about using their experience to design controls that are both safer and usable.

Input routeWhat it can revealHow to use it
Task walk-throughActual sequence, shortcuts and hidden exposure points.Update risk assessment and method statement. HSE managing risks and risk assessment
Trial of controlWhether the control is awkward, slow or incompatible.Improve design before full rollout. HSE managing risks and risk assessment
Near-miss reportingWeak signals where controls almost failed.Review controls and share learning. HSE managing risks and risk assessment
Safety representative reviewPatterns across teams and shifts.Bring worker voice into formal review. HSE managing risks and risk assessment
Post-change feedbackWhether the new control creates new hazards.Adjust and verify after implementation. HSE managing risks and risk assessment

How does the hierarchy support process safety?

In process safety, the hierarchy helps decide how major accident hazards are prevented, detected, controlled, mitigated and assured.

For major accident hazards, the starting point is the scenario: loss of containment, fire, explosion, toxic release, overpressure, runaway reaction or confined atmosphere. The hierarchy then challenges whether the inventory, pressure, temperature, ignition risk, human intervention or exposure route can be reduced before relying on alarms and emergency response. HSG254 Developing process safety indicators

A barrier-led view is essential. Controls such as containment, relief systems, detection, shutdown, isolation, ventilation, deluge and emergency response should be connected to the major accident hazard register and tested through assurance.

ScenarioHigher-order controlAssurance question
Flammable liquid storageReduce inventory, bund, segregate and control ignition.Are bund inspections, DSEAR zones and ignition controls current? HSG254 Developing process safety indicators
Pressure system overpressureDesign pressure relief and reduce blocked-in scenarios.Is the written scheme, relief valve testing and MOC current? HSG254 Developing process safety indicators
Runaway reactionEliminate incompatible additions and automate interlocks.Are trips tested and bypasses controlled? HSG254 Developing process safety indicators
Toxic gas releaseMinimise inventory, enclose, detect and isolate.Do detectors, alarms and emergency actions work together? HSG254 Developing process safety indicators
Line breakingDesign drain/vent points and verify isolation.Does permit evidence prove zero energy and no trapped contents? HSG254 Developing process safety indicators

How should the hierarchy appear in risk assessments?

The assessment should show the reasoning behind control selection, not simply list a few familiar precautions.

A useful assessment includes the hazard, people at risk, credible harm, existing controls, additional controls and review triggers. The hierarchy should be visible in the additional controls: what could be eliminated, reduced, isolated or engineered before relying on rules and PPE? HSE five-level hierarchy

For high-risk work, the hierarchy should also link to permits, change control, pre-start checks, emergency arrangements and close-out evidence.

OutputWhat it should showWhy it matters
Control rationaleWhy the chosen control is suitable.Prevents copied or weak controls. HSE five-level hierarchy
Rejected optionsWhy stronger options were not selected.Supports ALARP and review. HSE five-level hierarchy
Residual riskWhat risk remains after controls.Shows whether work can proceed. HSE five-level hierarchy
VerificationHow controls will be checked.Turns planning into assurance. HSE five-level hierarchy
Review triggerWhat change means the assessment must be updated.Keeps controls current. HSE five-level hierarchy

How can design and procurement strengthen controls?

Designers and buyers often have more control over risk than the people who eventually use the equipment or product.

Procurement can accidentally import risk by buying noisy, high-vibration, dusty, flammable or toxic equipment and substances because they are cheaper or familiar. A strong system builds safety into purchasing rules: approved suppliers, technical specifications, pre-purchase risk review and trial feedback. HSE five-level hierarchy

Design decisions also matter. Floor layout, access, isolation points, maintenance clearances, lifting points, ventilation and containment are all hierarchy decisions.

Decision pointHierarchy opportunityEvidence
New equipmentBuy guarded, quieter, lower-vibration or easier-to-maintain equipment.Specification, risk review and acceptance check. HSE five-level hierarchy
New substanceSelect safer product before first use.SDS review, substitution record and COSHH assessment. HSE five-level hierarchy
Building designRemove work at height and manual handling during maintenance.Design review and maintainability assessment. HSE five-level hierarchy
Contract packageSpecify control standard before tender.Contractor rules, pre-qualification and bridging document. HSE five-level hierarchy
Temporary worksDesign stable, collective protection before site improvisation.Temporary works design and inspection record. HSE five-level hierarchy

How should controls be checked after implementation?

Controls should be checked at the point of use, through second-line assurance and through deeper audit where risk justifies it.

First-line checks are simple and repeatable: is the guard in place, is the LEV running, is the edge protection complete, is the permit signed, is the isolation locked? Second-line assurance looks deeper at whether the control standard is understood and applied across activities. Third-line audit tests whether the system itself is effective. HSG254 Developing process safety indicators

A control that is never checked should not be trusted for long. Assurance is how the organisation learns whether the hierarchy decision is still alive in the workplace.

LevelTypical activityWhat good looks like
First line verificationSupervisor or worker pre-use check.Closed questions, yes/no data and immediate action for failed controls. HSG254 Developing process safety indicators
Second line assuranceManager or HSE adviser topical review.Samples tasks, records and observations, then ranks findings and actions. HSG254 Developing process safety indicators
Third line auditInternal auditor, specialist or external consultant.Tests system design, evidence, competence and management review. HSG254 Developing process safety indicators
Management reviewSenior review of trends and unresolved risk.Resources are allocated to stronger controls and overdue actions. HSG254 Developing process safety indicators

How should management verify controls for this task?

For silica-containing block cutting on a refurbishment site, the management check should start with a real control decision: Design, procurement or planning challenge completed before work starts. Name the person who will test it, keep evidence from the actual work, and reopen the assessment when the failure condition in the hierarchy table occurs. HSE management-system guidance.

A review should compare the planned control with what workers and supervisors can use in practice. Record the defect, owner, interim protection, verification and next review trigger so that a policy statement or certificate does not stand in for a working control.

How does this topic align with ISO 45001?

Use these examples to connect the relevant clauses to your own occupational health and safety management system. For each clause, identify the person responsible, the control in use and the evidence that it works.

Scroll across the table to read all four columns.

ISO 45001 clause alignment for Hierarchy of Controls
ISO 45001 clauseHow it appliesWhat to put in placeHow to verify it works
6.1.2.1 Hazard identificationIdentify how people can be exposed across the full task before deciding which controls to use.Walk through the planned masonry work with the crew. Consider cutting, clearing dust, maintenance and people passing the work area.The assessment identifies the exposure routes and affected people. Observations and worker feedback confirm that the recorded method reflects the task.
8.1.2 Hierarchy of controlsThe control hierarchy prioritises eliminating the hazard and reducing risk at source before depending on behaviour or protective equipment.Consider ordering components cut to size first. If cutting remains necessary, select a suitable assessed method, source controls and any additional protection for the remaining exposure.Use procurement and method records to show which options were assessed. Observe the work to confirm the selected controls are available and used as intended.
9.1.1 Monitoring and evaluating performanceMeasure and review the performance of selected controls using evidence relevant to the risk.Define the indicators and checks that will show whether the cutting method controls dust, including competent exposure monitoring where appropriate. Agree who acts when a check fails.Compare the inspection or monitoring results with the defined criteria and check that failed controls prompted a response and a recorded recheck.

Selected applications of ISO 45001:2018 with Amendment 1:2024. Use the current standard for a full assessment and check the legal duties that apply to the work and location.

ISO 45001:2018 · 2024 climate action amendment · ISO 45002 implementation guidance · ISO technical committee clause FAQ

What must each role demonstrate?

Observed task decisions and stop points establish useful evidence of competence; a briefing alone does not authorise safety-critical work.

Record who assessed the demonstration, what field task or simulation was observed, and what change triggers reassessment. Match specialist sign-off to the actual hazard. HSE training and competence

RoleDemonstrationAssessor and recordReassess when
WorkerChallenge unnecessary cutting and demonstrate dust-control stop point.Supervisor observes actual cut and record.Material or tool changes. HSE construction silica control sheets
SupervisorVerify enclosure, extraction, wet method and RPE fallback.Manager observes setup and fault response.Equipment fault or new task. HSE construction silica control sheets
DesignerSpecify pre-cut or lower-risk material and check design effects.Competent peer reviews specification and trial.Design or supply change. HSE five-level hierarchy
PurchaserReject unverified substitutions or tools without effective extraction.Technical approver records comparison.Supplier or product change. HSE five-level hierarchy
AuditorTrace selected control to field performance and worker feedback.Competent peer samples control evidence.Incident, complaint or failed test. HSG65 Managing for health and safety

What warning signs show the hierarchy is not being used properly?

Warning signs appear when the organisation accepts familiar low-order controls without challenging whether stronger controls are reasonably practicable.

The most obvious sign is a risk assessment where every answer is training, PPE, signage or be careful. Another warning sign is when design or procurement decisions are made without HSE input and the site team is left to manage the risk later. HSE five-level hierarchy

Good organisations treat these as system weaknesses, not worker failures.

Warning signWhy it mattersAction
PPE is the first control listedHigher-order controls may not have been considered.Review elimination, substitution, isolation and engineering options. HSE five-level hierarchy
Controls are copied between tasksThe control may not match the actual hazard.Observe work and rewrite task-specific controls. HSE five-level hierarchy
Workers bypass controlsThe control may be unusable or poorly supervised.Investigate work design and improve the control. HSE five-level hierarchy
Procurement buys risky equipmentHazards are imported before assessment.Add pre-purchase risk review. HSE five-level hierarchy
No verification recordsControls may exist on paper only.Create first-line checks and audit sampling. HSE five-level hierarchy

What do the acronyms and key terms mean?

Acronyms should be understood before they are used in assessments, briefings, audits or learning answers.

Acronyms can exclude newer readers if they are not explained. This section keeps the main terms available at the end of the page so the article stays readable while still supporting learners and audit users.

AcronymMeaningPlain-English use
ALARPAs low as reasonably practicableRisk reduction principle used when deciding whether further controls are required.
ERICPDEliminate, Reduce, Isolate, Control, PPE, DisciplinePractical hierarchy used to structure control choices.
HIRAHazard Identification and Risk AssessmentStructured process for identifying hazards and assessing risk.
ISOInternational Organization for StandardizationStandards body behind ISO 45001 and ISO 31000.
LEVLocal exhaust ventilationEngineering control that captures contaminants near the source.
PPEPersonal protective equipmentPersonal protection used for residual risk.
RAMSRisk assessment and method statementCommon construction planning document.
SFARPSo far as is reasonably practicableUK duty concept requiring proportionate risk reduction.