SHARE Knowledge Hub

Job Hazard Analysis

Job Hazard Analysis (JHA) is a task-based risk assessment method that follows a job step by step, identifying sources of harm, affected people and controls for each stage. It exposes hazards hidden by broad procedures, from unexpected machinery movement and sharp edges to long-term dust or handling exposures. Workers and supervisors verify critical safeguards before work and pause when equipment, people or conditions change.

Updated 2026-10-19Great Britain and Northern IrelandVersion 2.7Owner: SHARE editorial teamNext review: before publication; proposed 2027-09-25 or earlier after change

Understanding Job Hazard Analysis

Job hazard analysis, often called job safety analysis, is a practical way to examine a specific task step by step, identify how people could be harmed and decide which controls must be in place before the work begins. The UK law requires suitable and sufficient risk assessment and effective controls; it does not prescribe a document named JHA for every job. A JHA is useful when the sequence, interfaces or conditions of a task need more detail than a broad workplace risk assessment provides.

Why this matters at work

Think beyond immediate trauma. Dust, noise, vibration, heat, fatigue and awkward posture may cause illness or cumulative injury. Review skin, eye and inhalation pathways for substances. Include people not performing the task: adjacent operators, cleaners, customers, visiting drivers and members of the public. Consider vulnerable people and whether a control suited to an experienced worker works for a new starter or contractor.

For each high-consequence step, ask how the task can deviate: wrong item selected, component fails, valve passes, load snags, equipment restarts, material behaves differently, person enters an exclusion area or weather changes. A simple "what if" discussion with workers can reveal credible paths that a generic hazard checklist misses. The goal is not to list every imaginable catastrophe but to test the controls against plausible failure.

How organisations manage this in practice

Check design, installation, inspection, maintenance, proof test and human access. A locked valve cannot protect a worker if it is the wrong valve; a local exhaust hood cannot control dust if the duct is blocked. State how the control is known to be effective today and what evidence supports that conclusion. Do not let a risk matrix reward a control that exists only in policy.

A hazard is a source or situation with potential to cause harm; risk concerns the chance and severity of that harm in the circumstances. A task step is a meaningful action or change of state. A control prevents, limits or responds to harm. Residual risk is what remains after reliable controls are applied. A JHA records these links so workers can see why a control matters, not just tick a box beside an equipment name.

The host normally knows the plant, hidden services, adjacent operations and emergency arrangements; the contractor brings method, equipment and task competence. Neither side should assume the other has assessed the whole interface. A joint walkdown and briefing should reconcile the host's site assessment with the contractor's task JHA, permits and equipment checks. Identify who controls access, isolation, alarms, vehicle movement and handback.

What are the key facts about Job Hazard Analysis?

JHA works best when it is specific, worker-informed and close to the task.

Break the job into steps

A good JHA follows the sequence of work rather than listing generic hazards.

Look for what can go wrong

Each step should ask what could harm people, plant, environment, quality or continuity.

Use the hierarchy of controls

Start with elimination, reduction, isolation and engineering controls before relying on PPE or behaviour.

Use workers' knowledge

People who do the task often know the hidden snags, awkward postures and real shortcuts.

Brief and verify

A JHA is useful only when it is understood, used and checked at the point of work.

Review after change

New people, weather, equipment, sequence, location or simultaneous operations (SIMOPS) can invalidate the original analysis.

What is Job Hazard Analysis in plain English?

Job Hazard Analysis (JHA), also called Job Safety Analysis (JSA), examines a defined job in the order it is done. For each step the team identifies who could be harmed, how that harm could happen and what must be in place to prevent it.

A hazard is a source of harm; risk considers the likelihood and severity of that harm in the actual circumstances. A sharp edge may cause an immediate cut, while repeated force, dust or noise may damage health over time. A good analysis considers both, including people nearby and those cleaning or maintaining equipment later.

Define a useful boundary: “prepare and cut these metal channels in this work area”, rather than “use tools safely”. Walk and talk through the real task with workers. The record should make the safe sequence easier to understand and reveal decisions that need technical advice.

The task method matters because different steps open different routes to harm. Contact with moving machinery or an edge can injure immediately; repeated force or inhaled dust may cause harm over time. These examples are prompts for identifying the real material and process, not a claim that every JHA has every hazard.

Task and route to a personPlausible harmWarning and stop point
Conveyor jam: stored energy or unexpected movement reaches a maintainer at the nip or driveCrush injury, entanglement or amputation can be severe immediately.Unknown energy path, movement or failed isolation: keep clear and hold for the competent maintainer.
Metal channel preparation: cutting edge or unstable stock contacts a hand or footLaceration or puncture, with severity affected by sharpness, force and position.Tool defect, slipping workpiece or excessive force: stop and recheck selection and support.
Silica-containing material cut or drilled: fine airborne dust is breathed into lungsRepeated exposure can cause silicosis, COPD or lung cancer; effects may be delayed. Not a claim about the metal-channel example.Unknown material or ineffective dust control: hold and obtain a task-specific exposure-control method.
Repeated handling: force, awkward posture or repetition stresses back and limb tissuesSprain may occur at once; cumulative musculoskeletal disorder can develop over time.Pain, repeated awkward lifts or failed handling aid: pause, report and redesign the task.

Source routes: HSE: maintenance of work equipment, HSE L22: safe use of work equipment, HSE: construction dust and HSE: construction manual handling.

How does JHA relate to risk assessment, RAMS and safe systems of work?

JHA is one method of analysing task risks. It can contribute to, or form part of, a suitable task risk assessment; these labels overlap and do not have a universal legal hierarchy.

TermPractical purposeBoundary
Risk assessmentIdentify harm, evaluate risk and decide controls.A JHA must evaluate significant risks, not merely list hazards.
RAMSRisk assessment and method statement used together.A site or contract may require this package; the name alone proves nothing.
Safe system of workThe people, equipment, method, supervision and emergency arrangements for safe work.A document describes the system; the workplace must actually deliver it.
Permit to workFormal control and authorisation for specified work under local arrangements.Does not replace assessment, isolation or competence.
Point-of-work reviewCheck the planned method against actual conditions.Pause and escalate changes beyond the team’s authority; do not improvise a new high-risk method.

HSE: construction administration explains the use of method statements in construction. There is no blanket legal requirement for every job to have a document named JHA or RAMS. Particular work may require written arrangements and the employer still has risk-control duties.

When should a Job Hazard Analysis be used?

Use JHA where the job needs more detail than a generic risk assessment can provide.

Prioritise JHA for tasks with serious harm potential, incident history, new equipment, unfamiliar workers, non-routine maintenance, contractor interface, poor past compliance or changing conditions. Routine tasks may also need JHA where repetition creates health risks such as musculoskeletal strain, dust exposure, vibration or fatigue.

A practical programme starts with the highest risk tasks, then works through recurring tasks that create the most exposure, defects, near misses or uncertainty.

Use JHA whenReasonExample
High consequenceSmall error could cause serious harm.Confined space support, line breaking or live services.
Non-routine workPeople may be unfamiliar with hazards.One-off repair or emergency clean-up.
Task has incident historyPrevious harm shows hidden failure routes.Repeated cuts during packaging work.
Contractor interfaceDifferent organisations may assume different controls.Contractor works near live operations.
Work changes by locationGeneric method may not fit the site.Roof work, excavation or lifting on a constrained site.
New people or equipmentCompetence and assumptions may be untested.New hire operating a different saw or MEWP.

The same task-analysis method transfers between sectors, but the hazard, strongest feasible control and stop point change. These illustrations are distinct starting questions for a local assessment, not ready-made RAMS.

Sector task and affected peopleHarm route and outcomeStrongest controls, safeguard and check
Manufacturing: contractor clears a conveyor jam; maintainer and adjacent operatorsUnexpected movement or stored load reaches a person at the mechanism; crush or entanglement injury.Design out frequent manual access where feasible; machine-specific isolation and guarding, then coordination and controlled hand-back. Hold if an energy path is unknown.
Construction: cut or drill a confirmed silica-containing product; operator and nearby tradesRespirable crystalline silica reaches lungs; repeated exposure can cause serious delayed disease.Use pre-cut material if feasible; use a lower-dust process and suitable on-tool extraction or wet control plus assessed RPE where needed. Stop for unknown material or failed control.
Hospitality: open a food package or prepare food; kitchen staff and cleanersKnife moves toward the non-knife hand or is mishandled in washing; cuts, sometimes severe.Specify easy-open packaging or a suitable safer opening tool where practicable; stable surface and safe knife selection/storage, then task-specific instruction. Hold on damaged or unsuitable tools.
Logistics: receive a delivery and change a waste skip; drivers and pedestriansVehicle and pedestrian routes intersect during manoeuvring; collision may cause serious or fatal injury.Avoid reversing where practicable, separate routes and provide controlled crossing/loading areas. Coordinate infrequent deliveries and stop if segregation fails.

Sector source routes: HSE: maintenance of work equipment, HSE: construction dust, HSE: safe use of knives in kitchens and HSE: workplace transport safety. The metal-cutting worked example below is a fifth task variation.

How should a Job Hazard Analysis be completed?

Define the task, involve the people doing it, analyse the sequence and verify the controls before starting. Use enough steps to expose important decisions without making the record unusable.

  1. Set the boundary: identify the task, location, materials, equipment, interfaces and desired hand-back condition.
  2. Walk through safely: use workers, instructions, drawings and incident learning. Do not perform a dangerous task merely to observe it.
  3. Break down the sequence: include setup, normal operation, foreseeable interruptions, cleaning and completion. There is no universal required number of steps.
  4. Assess each step: explain who could be harmed and how, existing safeguards and what remains unresolved.
  5. Choose controls: eliminate or redesign where practicable, identify dependencies and assign an owner to each necessary action.
  6. Set hold points: name who verifies critical conditions and who can authorise a changed method.
  7. Brief and demonstrate: check understanding at the workface; resolve questions before exposing people.
  8. Observe and review: verify the method works, record defects and incorporate learning into the controlled version.
  9. Complete and hand back: account for tools, waste and temporary controls; restore safeguards only under the authorised method; record defects and residual restrictions; communicate the asset or work-area status and obtain the required release before normal use resumes.

A signature or favourable score does not release an unmet prerequisite. The named task owner confirms that the completion and hand-back step above has been verified.

A risk matrix can help prioritise work if your organisation uses one, but a score does not validate a missing safeguard. Do not label the residual risk “low” just because a control is written down.

Use the HSE risk-assessment steps to identify who can be harmed and what control is needed, then use HSE human-factors guidance to check whether the sequence is realistic for the people, workload and interruptions involved. For the metal-cutting task, the supervisor should show the selected tool and known material at the bench; if the delivered profile differs from the drawing, the planned low-risk score is irrelevant until compatibility and controls are reassessed. For maintenance and equipment work, HSE maintenance guidance supports a controlled return to use after safeguards and equipment condition have been checked.

What hazard prompts should a JHA use?

Good prompts help people see hazards that familiar work can hide.

Walk the job in its real location with the people who do it. For each step, ask what energy, substance, movement or interface could reach whom, how the exposure would occur, and whether the proposed safeguard is present and usable. A prompt list should reveal overlooked hazards; it cannot replace observation of the task.

Prompting should cover safety, health, environment and human factors. A JHA that only looks for immediate injury may miss dust, noise, vibration, fatigue, chemical exposure, poor access, weather, distraction, isolation failure or contractor conflict.

A practical supervisor can use the prompts below during a task walkdown, then turn the relevant ones into controls and evidence.

Prompt areaQuestions to askExample controls
EnergyCan anything move, fall, start, pressurise, heat or energise?Isolation, lockout, chocks, barriers and verification of the safe condition.
People positionWhere are hands, eyes, body and line of fire?Hold points, exclusion zones and tool positioning.
SubstancesCan dust, fumes, vapour, liquid or biological material be released?COSHH controls, LEV, RPE, hygiene and spill response.
Work equipmentIs the tool suitable, guarded, inspected and maintained?Pre-use check, correct accessory and defect quarantine.
EnvironmentCan weather, lighting, noise, heat, space or traffic affect the job?Lighting, work planning, traffic control and breaks.
Human factorsCan time pressure, workload, fatigue, poor instructions or unfamiliarity cause error?Briefing, supervision, pause points and usable procedures.
InterfacesCan other work affect this task?SIMOPS review, permit coordination and communication.

Use the HSE risk-assessment steps to turn a relevant prompt into a decision: name the affected person, exposure route and existing safeguard, then check at the job whether the proposed change actually breaks that route. Omit prompts that do not apply, and add a new one when the work changes.

How can the hierarchy of controls turn a job hazard analysis into effective task controls?

First ask whether the hazardous work can be avoided or redesigned. Prefer controls that prevent exposure at source over measures that depend on constant attention; PPE protects against remaining risk and cannot repair a missing guard.

For metal framing, ordering the required lengths may remove on-site cutting. Where cutting is necessary, select a suitable process, support the material, control access and manage sharp edges, noise or airborne contaminants as the actual method requires. Briefing and supervision support these arrangements throughout.

Selection questionDecision and evidence
Can supply remove the cut?Check design dimensions and delivery practicality with the planner. Record why on-site cutting remains necessary.
Will a manual cutter do the job?Compare exact material, profile, thickness and required finish with the manufacturer’s intended use and capacity. A tool that looks large enough is not proof.
A power tool is proposed insteadHold the substitution. Check suitability, guarding, accessory compatibility, work support, noise/dust/spark risks and operator competence before changing the method.
Material or capacity is unknownDo not trial-cut to find out. Identify the material and obtain current instructions or competent supplier advice; approve and brief the revised method.

This is a selection decision, not a universal approval for a particular cutter. HSE L22: safe use of work equipment supports assessing both equipment suitability and the conditions of use. Eliminate, Reduce, Isolate, Control, Personal protective equipment and Discipline (ERICPD) is a learning mnemonic, not a substitute for the applicable legal principles or technical checks.

Apply both lenses to the cutting task: the HSE hierarchy puts elimination and substitution before engineering, administrative measures and PPE. The six-letter ERICPD check additionally asks whether the exposure can be reduced, people physically isolated, and the chosen controls maintained through checks and learning. This is a planning aid, not a separate legal duty or permission to skip higher-order controls.

The selected tool can introduce new hazards: a powered substitution may add dust, noise, sparks and maintenance demands. Reassess those routes rather than assuming a faster cut is safer. HSE control-hierarchy guidance supports the order of decisions; HSE L22 addresses equipment suitability.

The HSE five-level sequence below makes the choice for each actual hazard visible. In the ERICPD check, “isolate” means physical separation and “discipline” means verifying and maintaining an agreed safe method, not blame. These ideas sit within engineering and administrative measures, not as permission to skip stronger controls. The earlier six-stage table remains a memory aid for the cutting example.

On-site cutting: blade, sharp edge and dust controls

Assume a crew must shorten metal framing on a shared preparation bench. The immediate hazards are contact with a blade or shear, sharp cut edges and particles; a powered change may add noise, dust and sparks. The planning decision is whether cutting can be removed, then whether the selected process is actually approved for that profile and thickness. The JHA must make the trade-off and hold point visible.

Conveyor intervention: unexpected movement and stored energy controls

Assume a recurring jam requires access to a conveyor nip and a raised component. Unexpected restart, stored air or a falling part can cause crush injury even when a guard is open. The safest long-term answer may be an external inspection or clean-out redesign; for the remaining intervention, a proved, locked zero-energy state and mechanical support are prerequisites, not optional enhancements.

How should JHA include human factors?

JHA should consider how normal people behave under real work conditions.

HSE human factors guidance encourages attention to the job, individual and organisation. A JHA should therefore look at procedure usability, workload, fatigue, lighting, access, time pressure, supervision, competence, communication, control labels, awkward posture and whether the safest method is actually practical.

This is where JHA becomes more than paperwork. It tests whether the work system supports good performance or quietly invites shortcuts.

FactorPoor JHA missesBetter JHA asks
Procedure usabilityInstruction is too long or vague.Can the worker follow it at the job location?
CompetenceAssumes everyone knows the task.Who is new, unfamiliar or needs supervision?
WorkloadControl relies on perfect attention during pressure.Where are pause points and independent checks needed?
EnvironmentLighting, heat, noise or cramped space omitted.Can the task be done safely under actual conditions?
InterfacesOther teams or contractors ignored.What SIMOPS or handover risk exists?
DriftCustom and practice differs from the written method.What do workers actually do and why?

The HSE human-factors guidance makes this a work-design check. If a worker must reach across a moving conveyor because the access point is poorly placed, the answer is to change the access or work method, then test it at the machine; asking the worker to remember extra caution leaves the exposure route in place.

What does a routine cutting JHA look like?

For a BuildOut Ltd fit-out team, the key decision is to choose and verify the cutting method before setting up the work. The following teaching example assumes an identified metal channel and a manufacturer-approved manual cutter; it is not a ready-to-use site assessment.

Routine task: prepare metal channels for installation

Task material and setting: Cut identified metal channels to the drawing dimensions in a segregated indoor preparation area with suitable lighting and a stable bench. Avoid affecting adjacent trades, public routes or escape routes.

People and prerequisites: The operator and supervisor understand the cutter and material limits; nearby trades and waste handlers are included. The planner first considers supply at finished length. The supervisor confirms current instructions, tool condition, work support and suitable protection for sharp edges; the worker demonstrates the intended method.

Before: Match material/profile/thickness to tool capacity and the required finish. Establish the layout and waste container. Check the tool as instructed and secure/support the work using the specified arrangement; keep hands clear of the cutting action. Brief the stop conditions.

During: Follow the verified manual-tool method, maintain clear access and control sharp offcuts. Keep others outside the immediate work area. Report excessive force or an unexpected result rather than forcing the cut.

Hold or stop: Stop for a damaged tool, unstable support, unknown coating/material, unexpected movement, a person entering the area or a proposed powered-tool substitution. The supervisor obtains competent advice and authorises a revised assessment before resumption. An injury or other emergency activates local first-aid/emergency arrangements.

Completion and hand back: Check cut pieces and sharp edges are safely handled, collect offcuts, make the tool safe and store it as instructed. Report defects, confirm the preparation area is safe for others and return it to the site supervisor.

Evidence: Retain the material/tool identification, instruction reference, task assessment version, briefing and control verification, changes/defects and hand-back record. A signature alone is not evidence that the controls worked.

HSE L22 helps the supervisor test whether the chosen cutter is suitable for this profile and remains safe in use. The drawing and tool name alone are insufficient when the delivered metal or accessory differs from the assumed specification.

Illustrative completed chronological JHA

This teaching record develops the existing metal-channel example. JHA-CUT-01 revision 2 is an illustrative identifier, not a site authorisation. Judgements explain the dependencies rather than assigning an invented numerical risk score. Each named role resolves its action before the stated hold point; an unmet prerequisite keeps that step on hold.

Five steps, with a hold before exposure

  1. Identify stock.
    Hold for unknown identity or tool capacity.
  2. Position and support.
    Verify stability, hand clearance and segregation.
  3. Cut.
    Stop on abnormal force, movement or intrusion.
  4. Handle and deburr.
    Verify the assessed finish and sharp-edge method.
  5. Collect and hand back.
    Supervisor accepts the safe area and restrictions.
Text equivalent: follow steps 1–5 in the completed record. Any failed prerequisite returns to the supervisor for correction, revalidation and briefing before that step resumes.

Completed JHA: identified metal channel and approved manual cutter
Task stepAffected person and harm routeChosen controls and reasonQualitative judgementAction owner and deadlinePre-release verification
1 · Identify stockOperator and later installer: wrong material or forced tool use can cause loss of control and cuts.Planner considers finished-length supply; supervisor matches drawing, profile and thickness with current cutter capacity and instructions.Unresolved until identity and compatibility are demonstrated; no trial cut to find capacity.Supervisor resolves any mismatch before setup; unknown coating goes to competent advice.Material ID, instruction reference and measured profile checked against JHA-CUT-01 revision 2.
2 · Position and supportOperator or nearby trade: unstable stock, pinch points or falling length can injure hands and feet.Stable specified support and segregation; worker suggests moving the offcut bin beside the bench to avoid carrying sharp scrap across the walkway. Supervisor revises layout before briefing.Conditionally tolerable only with verified stable support and a clear protected route.Tool owner secures the specified support; supervisor verifies the revised bin location before cutting.Operator demonstrates stock stability and hand clearance; supervisor confirms boundary and access remain clear.
3 · CutOperator and bystanders: cutting edge, unexpected movement or excessive force can cause serious laceration.Use only the identified manufacturer-approved manual method; keep hands clear, maintain support, use assessed protection and stop on abnormal force or movement.Control-dependent: a damaged tool or unstable stock is unacceptable regardless of any recorded score.Operator stops; supervisor and tool owner resolve defects or obtain competent method review before resumption.Tool condition, protection and method demonstrated; a powered-tool change requires a revised assessment and briefing.
4 · Handle and deburrOperator and installer: sharp edges, projections or an unsuitable finishing method can cut or puncture.Use the assessed edge-handling and finishing method with suitable support and task protection; keep finished stock stable and separate from scrap.Residual sharp-edge exposure remains; control must be verified for the actual finish and handling route.Supervisor approves any additional finishing operation before it starts; operator reports an unexpected edge or coating.Check sample finish and safe handling without testing sharpness by touching an edge; confirm installer information.
5 · Collect offcuts and hand backWaste handler, cleaner and other trades: loose sharp scrap, unsafe tool storage or obstructed access can cause cuts and trips.Collect into the agreed suitable container by the assessed method, make and store the tool safely, inspect the area and record defects or restrictions.Area stays restricted until sharp waste, tool condition and route checks are accepted.Operator completes cleanup; site supervisor accepts area hand-back before other trades return.Record waste and tool checks, defects and named acceptance against JHA-CUT-01 revision 2.

How does JHA change for non-routine maintenance?

Maintenance must analyse stored energy, unexpected restart and the handover between operators and contractors. Pressing a stop button does not prove isolation. This example teaches the decisions; a competent person must define the machine-specific safe method.

Non-routine task: investigate a jammed conveyor

Task material and setting: Investigate and clear a jam on an electrically driven conveyor in a busy distribution area. Connected conveyors, gravity-loaded material and stored mechanical energy may affect the task.

People and prerequisites: A competent maintainer leads the work with the operator and site supervisor. Contractor staff, adjacent operators and cleaners need coordinated boundaries. Current machine information, isolation arrangements, access, suitable tools and recovery/emergency plans must be available.

Before: Secure the work area and arrange alternative operations. Identify all energy and material-feed paths. Under the approved equipment-specific procedure, authorised people isolate, secure against reconnection, control stored energy and verify the safe condition before entry or guard removal. Obtain any locally required permit and explicit release of the maintenance hold point.

During: Maintain control of isolations and access. Use the assessed method and communicate with connected operations. If testing needs energy, stop the maintenance phase and use a separately assessed, authorised test procedure; nobody bypasses protection to “see what happens”.

Hold or stop: Unknown energy sources, unreliable isolation, unsupported loads, missing guards, unexpected movement or changed work scope stop the job. Keep people clear and get the competent maintainer/site controller. For injury, fire or uncontrolled movement use emergency arrangements; do not enter a danger zone for an improvised rescue.

Completion and hand back: Account for people, tools and removed parts. Reinstate guards and safety devices, check their function under the approved process, and coordinate removal of isolations and controlled return to service by authorised people. The operator accepts hand-back; unresolved defects remain recorded with the equipment unavailable as required.

Evidence: Keep the JHA/permit version, isolation and verification records, contractor coordination, defects and repairs, test results and named operational acceptance. Feed the cause of the jam into prevention and maintenance planning.

HSE L22 supports the equipment-use and maintenance decisions in this example. Before the permit is released, the isolator must still identify the actual machine energy paths and prove the safe state at the work location.

Why the task changes the analysis: a conveyor jam may be brief, but access inside guarding introduces a different harm route from routine operation: electrical or pneumatic restart, stored motion and gravity can act while a maintainer is within the machine. The authorised isolator therefore checks each energy path and proves the safe state before the contractor enters; the operator cannot substitute a stopped control button for that evidence. Restart belongs to the named operations owner after tools, people and guards are accounted for. HSE maintenance guidance explains isolation, stored-energy release and safe hand-back.

Linked records and separate release gates

The following identifiers are teaching links between records for one job. At a shift, scope, plant-state or relevant personnel change, suspend the affected work and revalidate the JHA, isolation and any permit/test authorisation with the incoming responsible people. Record the revised version and rebrief before release; an unexpired document does not settle a changed condition.

Conveyor maintenance: five decisions with different owners
Decision / linked recordDecision ownerRequired evidence and limit
JHA approvalCompetent maintainer and site supervisorJHA-CONV-01 identifies the actual machine, energy paths, scope, people and controls. Approval of the analysis does not release a permit or prove isolation.
Permit release, where requiredPermit issuer / site controllerPTW-CONV-01 cross-refers to the approved JHA and isolation certificate; issuer verifies prerequisites and simultaneous work. Not every task needs a permit; follow the assessed local system.
Isolation verificationAuthorised isolator and designated checkerISO-CONV-01 identifies every energy/feed path, securing and stored-energy control, and proof at the workface. Entry or guard removal stays on hold until proved safe; monitor and re-prove as the procedure requires.
Energised test authorisationCompetent test lead and site controllerTEST-CONV-01 separately assesses the test boundary, people clear, safeguards and controlled energisation. End the maintenance phase before the authorised test; re-isolate and verify before further intrusive work.
Operations acceptanceNamed operations owner / operatorHB-CONV-01 records completion, people/tools accounted for, guards and protection reinstated, defects/restrictions and authorised isolation removal. Accept and monitor the controlled return to use; a completed JHA is not restart authority.

For process-plant permit practice, read HSE HSG250: permit-to-work systems; apply its industry scope and the actual site arrangements.

How should JHA be briefed and supervised?

A JHA should be briefed as a working method, not handed over as a signature sheet.

At the point of work, the supervisor should ask the team to explain the sequence, the highest-consequence step and the stop trigger in their own words. Check that the actual guard, isolation, extraction or exclusion arrangement matches the record. If it does not, pause the job and amend the method before resuming. HSE worker-involvement guidance (GB) supports consulting the people who perform the task.

A good briefing confirms the task, steps, high-risk points, critical controls, emergency arrangements, stop-work triggers and who has authority to pause the job. Workers should be encouraged to challenge anything that does not match the real work.

Supervision should focus on critical steps and controls. Watching whether the JHA is followed is also a monitoring activity: it reveals whether the method is realistic, whether training is effective and whether the organisation is learning.

CheckGood questionEvidence
Task understandingCan workers explain the job and sequence?Briefing record and worker confirmation.
Critical controlsDo people know which controls must not fail?Control checklist and supervisor observation.
Stop-work triggersWhen must work pause?Clear stop criteria in JHA/RAMS.
Emergency arrangementsWhat happens if someone is injured or exposure occurs?First aid, rescue and communication plan.
Change controlWho can approve a changed method?Supervisor/permit authority named.
LearningWhat feedback came from the team?Updated JHA and action tracker.

What is a point-of-work risk assessment?

A point-of-work risk assessment (POWRA) is a short check with the people doing the job at the actual work location. It checks that the planned method and safeguards still fit the conditions and makes a clear decision to proceed, hold or stop.

Use the check to confirm that the job hazard analysis still matches the task steps and the controls the team can actually use. A new step, different equipment or a changed work area can alter who is exposed and how. Stop the affected step, escalate the change, update the analysis where needed and rebrief before resuming.

Use the POWRA alongside the task risk assessment, safe system of work and any permit, isolation or specialist assessment required for the job. A tick, signature or low score cannot make a missing safeguard acceptable or authorise a changed task.

Read the full point-of-work check and example.

Download the blank POWRA template in Word or PDF.

HSE steps needed to manage risk · HSENI risk assessment guidance

How should JHA handle change and dynamic risk?

A JHA is a baseline, not a guarantee that every future condition is covered.

Conditions change: weather deteriorates, a new worker arrives, a different tool is substituted, nearby work starts, lighting fails, the job takes longer, access changes or a hidden service is found. The team should know which changes require a pause, reassessment and authorisation.

Dynamic risk assessment should not mean making it up as you go along. It means comparing the real situation with the planned JHA, then deciding whether work can continue, needs additional controls or must stop.

For example, if the metal channel is replaced with a coated material during a fit-out, the worker pauses cutting. The supervisor checks the material and tool instructions, reassesses possible airborne contamination, sparks and waste, and obtains specialist advice where the coating is unknown. A revised method is briefed and the extraction or alternative cutting arrangement is checked before the job restarts; the change, owner and authorisation are recorded. See HSE risk-assessment steps; HSENI risk-assessment guidance; HSE construction-dust guidance.

TriggerWhy it mattersAction
Different tool or materialHazards and controls may change.Review steps, PPE and equipment controls. (see HSE risk assessment)
Different locationAccess, public interface or environment may differ.Walkdown and update JHA. (see HSE risk assessment)
New or inexperienced workerCompetence assumptions may be wrong.Brief, supervise and adjust task. (see HSE human factors)
SIMOPSOther work may introduce new hazards.Coordinate permits and interfaces. (see HSE risk assessment)
Weather or lighting changeSlips, visibility, heat or wind risk may change.Pause and reassess. (see HSE risk assessment)
Incident or near missExisting controls may be weak.Investigate and update JHA before repeat work. (see HSE HSG245)

What evidence shows JHA is working?

Evidence should prove JHA is used to improve actual work, not just to collect signatures.

Sample completed analyses against observations of real jobs. A useful record shows who walked the task, which control was changed, how the worker learned the method and what happened after a near miss or changed condition. Repeated generic wording, missing owners or a signature with no field check indicate that the analysis is not controlling work. HSE HSG65 (GB) links planning, control checks and learning.

For the cutting JHA, put the current material specification, manufacturer-approved tool range, pre-use guard and support checks, worker demonstration and an observation of a real cut beside the signed analysis. For conveyor maintenance, compare the written energy map with the isolation points actually locked, the prove-zero record, supports for stored energy and the signed hand-back. If the field setup differs, the supervisor stops the task and changes the method before the record can be treated as current.

EvidenceWhat it may indicateQuality check
Task-specific JHAThe planned task has been described in steps that can be checked at the workface.Could a worker recognise the job from the document?
Worker involvementWorkers had an opportunity to describe how the task is actually done.Are worker names/comments included?
Control selectionThe proposed controls were selected and assigned, subject to field verification.Are controls specific and practical?
Briefing recordThe briefing took place and questions or challenges were recorded; comprehension still needs a demonstration.Does briefing include questions/challenges?
Supervisor observationA sample of the real work was compared with the agreed critical controls.Were critical controls verified?
Change recordA revised method was issued after a recorded change; workers still need the current version.Are revisions dated and communicated?
Learning recordA reported problem led to an assigned improvement whose effectiveness can be checked.Are lessons closed into standards?

What competence do the different roles need?

People need the knowledge, practical ability and authority to make the decisions assigned to them. A JHA course or attendance signature does not by itself prove competence for operating, isolating or maintaining particular equipment.

Workers should explain the sequence, demonstrate critical controls and know how to pause and report a mismatch. Supervisors need to facilitate a realistic walkthrough, check understanding, verify controls and recognise when specialist advice is needed.

Planners and purchasers should identify task requirements and obtain the correct equipment/material information. Maintainers and permit/isolation roles need the specific competence and authorisation for the plant and energy systems. Managers and auditors should sample work in progress and evidence of action completion, not just count signed forms.

Use practical scenarios, observation and supervised performance where appropriate. Refresh or reassess when equipment, role or conditions change, when work is rarely performed, or when performance shows a gap. Do not invent a universal JHA certificate expiry or annual refresher requirement.

RoleLearning and demonstrationAssessor and recordReassessment trigger
Nearby workers and new startersRecognise the task boundary, affected people, hazards and stop route.Supervisor checks a short scenario explanation and briefing record.New site, task or missed stop signal.
Task workers and contractorsWalk the job, identify exposure at each step and demonstrate critical checks.Supervisor observes the real task and records the agreed method.Changed material, tool, sequence, team or unsafe observation.
Specialist maintainersProve isolation, stored-energy control, test and hand-back for the equipment in scope.Authorised technical assessor reviews practical demonstration and permit evidence.New equipment, defect, failed isolation or long gap in practice.
Supervisors and permit issuersChallenge vague controls, verify prerequisites and pause after change.Manager samples a live JHA, field observation and hold record.Incident, repeat generic wording or changed interfaces.
Managers and plannersSelect tasks needing detailed analysis, allocate time and remove design barriers.Senior manager reviews risk decisions, resources and action closure.New process, recurring near miss or audit finding.
Safety advisers and auditorsEvaluate hazard pathways, source scope, GB/NI duties and control effectiveness.Competent peer review and audit sampling record the judgement.New authority, conflicting source or poor field match.

How can learners test their understanding?

Explain the harm mechanism and the decision, then show how the control is verified. A strong answer connects assessment to work as done.

Try the cutting example: the replacement cutter looks similar, but its material capacity is missing. Explain why the team holds the substitution, what information the purchaser obtains, who reviews the changed method and how the workers are briefed. Then explain why a risk score or signature cannot resolve the missing specification.

Compare the conveyor task: identify the maintenance hold point, the difference between stopping and isolating, and the checks needed before the operator accepts the plant back. These are learning questions, not authority to perform isolation.

How should JHA fit workplace risk management?

Use the task analysis to connect the real work sequence to an assessed hazard, a practical control, a named owner and a field check.

For metal cutting, confirm the supplied material and manufacturer-approved tool range before the supervisor releases the task. If a powered substitution changes sparks, noise or dust, reassess the method with the people doing it; an old signature cannot validate the new exposure. HSE risk-assessment guidance supports choosing and reviewing controls.

For conveyor maintenance, the approved analysis needs the actual energy map, locked isolations, stored-energy support, proved safe state and named hand-back. HSE maintenance guidance addresses those practical controls; HSE HSG65 supports management review when a repeated defect or changed task exposes a weakness.

The supervisor checks a sample of work as done and records any hold, change and restart. The safety adviser looks for repeated gaps; the manager supplies the design or equipment change needed to remove them. The documented method has value only when those checks show the control is usable at the workface.

What warning signs show JHA is weak?

Weak JHA usually shows up as generic wording, signatures without understanding and work that has drifted away from the document.

If the evening shift uses a powered cutter because the manual tool cannot handle a changed profile, a morning-shift signature cannot authorise that new exposure. The supervisor holds cutting, checks the material and manufacturer limits, reassesses sparks, particles, noise and adjacent work, then briefs and observes the revised method. A repeat near miss after that change calls for investigation of selection and procurement, not another signature on the old JHA. HSE HSG245 supports moving from the event to underlying causes and corrective action.

Warning signWhat it suggestsAction
Same JHA used everywhereTask or site specifics are missing.Review at the point of work.
No worker inputHidden hazards may be missed.Involve people who do the job.
Controls are mostly PPEHierarchy has not been applied.Redesign controls before relying on PPE.
Workers cannot explain methodBriefing is ineffective.Rebrief and simplify.
Job changes but JHA does notChange control is weak.Stop and update JHA/RAMS.
Near misses repeatLearning is not being fed back.Investigate and revise standard methods.

What do the acronyms and key terms mean?

These terms identify the controls, decisions and records discussed above.

AcronymMeaningPlain-English use
JHAJob Hazard AnalysisStep-by-step task hazard analysis.
JSAJob Safety AnalysisAlternative term often used for similar task analysis.
RAMSRisk Assessment and Method StatementCommon UK planning package for higher-risk work.
SSoWSafe System of WorkComplete safe work arrangements.
ERICPDEliminate, Reduce, Isolate, Control, Personal protective equipment, DisciplineHierarchy of control prompt.
SIMOPSSimultaneous OperationsConcurrent work that can interact.
PPEPersonal protective equipmentProtection against remaining exposure after stronger task controls.

Documents to download

Download editable resources from the SHAREhub environment to support your work. Working forms and spreadsheet input areas are blank. Reports, plans, guides, briefings, procedures and policies contain completed fictional example content to adapt.

Return to SHARE home