SHARE Knowledge Hub

Hazard group - physical hazards

Physical hazards are workplace conditions or forms of energy that can injure people or damage their health. Examples include noise, hand-arm and whole-body vibration, heat and cold, poor lighting, radiation, pressure, slips and trips, falls from height, falling objects and work near water. Harm may follow a single event, such as a fall or impact, or repeated exposure, such as hearing damage from noise. A physical-hazard risk assessment identifies the source, route of exposure, people affected, duration and foreseeable failures. Employers should prevent the hazardous activity where practicable, reduce exposure at source, separate people from danger and verify the remaining controls. SHARE uses this practical hazard group to support task assessment; specialist topics and overlapping mechanical, electrical or ergonomic risks still require their own consideration.

Updated 2026-10-19UK workplace guidance

Understanding Hazard group - physical hazards

Physical hazards are workplace conditions or forms of energy that can injure people or damage their health. Examples include noise, hand-arm and whole-body vibration, heat and cold, poor lighting, radiation, pressure, slips and trips, falls from height, falling objects and work near water. Harm may follow a single event, such as a fall or impact, or repeated exposure, such as hearing damage from noise. A physical-hazard risk assessment identifies the source, route of exposure, people affected, duration and foreseeable failures. Employers should prevent the hazardous activity where practicable, reduce exposure at source, separate people from danger and verify the remaining controls. SHARE uses this practical hazard group to support task assessment; specialist topics and overlapping mechanical, electrical or ergonomic risks still require their own consideration.

Why this matters at work

Physical hazards arise from the work environment, energy, movement and exposure. Identify both immediate injury risks and health effects that develop over time. This research document explains mechanisms, control decisions, operational evidence and industry applications. It supports task specific risk assessment and source grounded intelligence responses. These groups overlap. Sharps can cause both mechanical injury and infection. Pressure guidance does not replace specialist assessment of vacuum systems. Temperature and radiation need exposure specific advice.

Physical harm can follow a sudden transfer of energy, loss of footing or prolonged exposure to noise, vibration, radiation and thermal conditions. Assess the source, transmission pathway and person exposed. Severity alone does not determine exposure, and the absence of immediate symptoms does not exclude cumulative damage. Separate a task observation from an exposure measurement. Engineering changes need verification under the operating conditions in which people actually work.

How organisations manage this in practice

Assign control ownership, competent verification and change triggers. Distinguish a completed action from evidence that the control works under actual conditions. Review changes and failures promptly, protect health information and retain previous versions; a schedule alone is insufficient. UK synthesis; HSE guidance is GB scoped and NI legal duties need NI authority.

Assess representative noise exposure with reliable information and competent interpretation. Reduce noise through processes, equipment and work methods; hearing protection alone cannot establish adequate control. Record owners and review actual changes without inventing numeric limits. UK synthesis; HSE guidance is GB scoped and NI legal duties need NI authority.

For a warehouse receiving operation, walk the vehicle and pedestrian routes with workers. Check unloading at height, falling loads, flooring, visibility, noise and vibration. Include maintenance, abnormal conditions and work near water where relevant. Prioritise layout and segregation, stable access and collective fall protection. Select quieter and lower vibration equipment, maintain lighting, assess thermal conditions and plan confined space avoidance and rescue. Refer pressure systems and radiation to competent specialists. Route plan and inspection records; height work plan; exposure assessments; equipment maintenance; pressure examination records where required; confined space authorisation and rescue arrangements. Follow the assessment through procurement, implementation, briefing, supervision and verification rather than stopping at a document.

What are physical hazards and what does their assessment cover?

Physical hazards arise from the work environment, energy, movement and exposure. Identify both immediate injury risks and health effects that develop over time. These groups overlap. Sharps can cause both mechanical injury and infection. Pressure guidance does not replace specialist assessment of vacuum systems. Temperature and radiation need exposure specific advice. See Preventing slips and trips at work and Working at height.

Start with the hazard group overview, then use the related topic links for task-specific background. A group checklist helps discovery; it does not establish that the controls at your site are effective. Read the hazard group overview.

Which hazards should the assessment consider?

Check each relevant mechanism during normal work, cleaning, maintenance, foreseeable failure and emergencies. Several entries can share a harm pathway; follow the linked explanation rather than treating each label as a separate assessment. See Preventing slips and trips at work and Working at height.

Hazard or exposure and practical application — part 1 of 4

Hazard or exposure and practical application — part 1 of 4. Compare the named situations, controls and evidence together. Original SHARE explanation; apply the linked source in its stated jurisdiction.
Learning point: Compare the named situations, controls and evidence together. Original SHARE explanation; apply the linked source in its stated jurisdiction.
Read the complete visual as text
  1. Slip trip and fall same level: Read the mechanism and controls: Slips trips and same level falls
  2. Working at height: Read the mechanism and controls: Work at height and falling objects
  3. Falling objects: Read the mechanism and controls: Work at height and falling objects
  4. Noise: Read the mechanism and controls: Noise exposure

Hazard or exposure and practical application — part 2 of 4

Hazard or exposure and practical application — part 2 of 4. Compare the named situations, controls and evidence together. Original SHARE explanation; apply the linked source in its stated jurisdiction.
Learning point: Compare the named situations, controls and evidence together. Original SHARE explanation; apply the linked source in its stated jurisdiction.
Read the complete visual as text
  1. Vibration: Read the mechanism and controls: Hand arm and whole body vibration
  2. Heat stress: Read the mechanism and controls: Heat cold and extreme temperatures
  3. Cold stress: Read the mechanism and controls: Heat cold and extreme temperatures
  4. Extreme temperature: Read the mechanism and controls: Heat cold and extreme temperatures

Hazard or exposure and practical application — part 3 of 4

Hazard or exposure and practical application — part 3 of 4. Compare the named situations, controls and evidence together. Original SHARE explanation; apply the linked source in its stated jurisdiction.
Learning point: Compare the named situations, controls and evidence together. Original SHARE explanation; apply the linked source in its stated jurisdiction.
Read the complete visual as text
  1. Radiation ionising and non ionising: Read the mechanism and controls: Ionising and non ionising radiation
  2. Poor lighting: Read the mechanism and controls: Lighting and visibility
  3. Confined spaces: Read the mechanism and controls: Confined spaces
  4. Pressure high and low: Read the mechanism and controls: High pressure low pressure and vacuum

Hazard or exposure and practical application — part 4 of 4

Hazard or exposure and practical application — part 4 of 4. Compare the named situations, controls and evidence together. Original SHARE explanation; apply the linked source in its stated jurisdiction.
Learning point: Compare the named situations, controls and evidence together. Original SHARE explanation; apply the linked source in its stated jurisdiction.
Read the complete visual as text
  1. Sharps: Read the mechanism and controls: Sharps particles and impact
  2. Flying particles: Read the mechanism and controls: Sharps particles and impact
  3. Impact by moving objects: Read the mechanism and controls: Sharps particles and impact
  4. Drowning: Read the mechanism and controls: Drowning and work near water

Describe when the source is created or released and how it reaches someone. Compare normal operation with receipt, setup, blockage, breakdown, disposal and contractor access. The list below is a discovery aid: an omitted mechanism may still be important, while an irrelevant item does not require a fabricated assessment. Follow the mechanism explanation and test controls against the actual circumstances before scoring risk.

How do physical hazards cause injury or delayed ill health?

Physical harm can follow a sudden transfer of energy, loss of footing or prolonged exposure to noise, vibration, radiation and thermal conditions. Assess the source, transmission pathway and person exposed. Severity alone does not determine exposure, and the absence of immediate symptoms does not exclude cumulative damage. Separate a task observation from an exposure measurement. Engineering changes need verification under the operating conditions in which people actually work. See Noise at work: A brief guide to controlling the risks and Hand-arm vibration at work: A brief guide.

A physical source can act through impact, heat transfer, pressure, vibration, sound or radiation. The affected tissue and timescale depend on the mechanism: an eye struck by a particle differs from hearing damaged by repeated noise. Compare exposure during production with setup and maintenance; a barrier that protects an operator may not protect the person cleaning behind it. Use the relevant specialist assessment rather than one universal score for all energy sources.

Which physical controls need competent design or specialist assessment?

Physical conditions often interact with transport, machinery and substances. A hearing protector does not control vehicle movement; a gas test does not establish structural stability or remove engulfment risk. Select each control for its mechanism and coordinate owners. Obtain competent input for pressure systems, radiation, exposure assessment and confined space planning. Numerical thresholds, rescue arrangements and equipment specifications must come from the applicable current source and site conditions. See Safe work in confined spaces and Pressure systems.

A designer or purchaser needs the actual task, loads, environment and access pattern before selecting protection. Supervisors need a usable acceptance check and a defect response, while operators need to recognise when the arrangement no longer matches the method. Source ratings, structural conditions, exposure assessment and rescue requirements cannot be guessed from a photograph. A changed tool, route or task may need competent reassessment before it is substituted into an existing plan.

How do slips, trips and same-level falls happen at work?

Footing can be lost through contamination, unsuitable surfaces, obstructions or changes in level. Carrying loads, poor visibility and rushing can compound the problem. Workers, visitors and public may encounter different routes. See Preventing slips and trips at work.

A restaurant kitchen spill can reach a waiter carrying hot food, while a distribution aisle becomes obstructed by discarded wrapping. The surface, footwear, walking route, load and visibility combine: a fall can be followed by a burn or impact with a vehicle. Rain tracked into a reception area is a different source from a leaking machine seal, so the control must address the origin, not just the wet patch.

Which source controls and checks change the outcome?

Eliminate leakage or trailing cables where practicable, substitute a less contamination-prone method and isolate unavoidable wet work behind a maintained dry route. Drainage and appropriate flooring are engineering measures; cleaning schedules and signs are administrative. The supervisor verifies the surface and barrier before reopening. Suitable footwear supplements the arrangement; it cannot compensate for uncontrolled oil, displaced barriers or a route that forces people into traffic.

How should the controls be applied?

Prevent leaks, organise storage and cables, choose suitable flooring and clean without leaving an exposed wet route. Separate people from contamination until the route is safe. Footwear supplements rather than replaces those measures.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Inspect routes during actual use and after cleaning. Record recurrent spills and defects; warning signs alone are not an adequate solution to persistent contamination.

How can people and objects fall from height?

A person may fall from edges, fragile surfaces, openings or access equipment, while objects can fall onto people below. There is no assumption that a short fall is harmless. See Working at height.

A stock picker reaches from an unsuitable platform; a roofer steps onto a fragile surface; a fitter drops a tool above an occupied walkway. Gravity transfers energy into the body at landing or impact, and even a modest fall can cause serious injury. The exposure also changes during access, removal of edge protection, material delivery and rescue.

Which source controls and checks change the outcome?

Avoid elevated work through ground-level assembly or remote access where feasible; prevent falls with suitable platforms, guarded access or other collective protection before relying on personal measures; if a fall cannot be prevented, minimise its distance and consequences. A competent planner selects and checks the actual platform, edge protection and exclusion arrangement, including access and loads. Personal fall protection requires compatible equipment, competence and a planned rescue. Stop when access, structure condition, protection or the rescue arrangement does not match the method.

How should the controls be applied?

Avoid work at height where practical; select suitable stable access and collective protection before personal fall protection. Secure materials and prevent access below. Plan rescue where relevant.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Check the surface, equipment, weather, competence and actual protection. Do not prescribe a ladder or harness simply from the job title.

When can workplace noise damage hearing?

Repeated or intense sound can damage hearing and also mask warnings or communication. Exposure depends on level, time, pattern and proximity; a noisy impression is not a measured daily exposure. See Noise at work: A brief guide to controlling the risks.

A fabrication operator may be exposed to repeated grinding, a cleaner to plant-room machinery and an event crew to amplified sound. Noise travels from the source to the ear; repeated or sufficiently intense exposure can damage hearing even without pain. Impulsive noise, duration, multiple machines and nearby staff matter, so a quieter-looking task is not necessarily controlled.

Which source controls and checks change the outcome?

Remove an unnecessary noisy step or select a quieter process; enclose or isolate the source while maintaining safe access and ventilation. A competent assessment determines the exposure and verifies the improvement under representative production, not only while the machine idles. Administrative exposure management and correctly selected, fitted hearing protection address remaining risk. Report unusual noise, failed enclosures and difficulty communicating warnings; review the process rather than simply increasing protection.

How should the controls be applied?

Reduce noise at source through equipment selection, damping, enclosure, maintenance and layout. Plan access and supplementary hearing protection based on a competent assessment.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Obtain suitable measurements when needed, check controls and arrange health surveillance where required. Do not infer compliance from ear defenders being issued.

How do hand-arm and whole-body vibration exposures differ?

Hand held tools transmit vibration to hands and arms; vehicles can transmit shocks and vibration through seats and feet. Tool condition, gripping, posture, terrain and exposure duration matter. These exposures require separate assessment; vehicle drivers can have interacting posture and handling demands. See Hand-arm vibration at work: A brief guide and HSE Whole body vibration at work.

An engineer using an impact tool receives vibration through the hands, while a forklift driver receives whole-body vibration through the seat on a damaged yard surface. Grip, force, operating time, tool condition, shocks, posture and route alter exposure. Tingling, numbness or persistent discomfort require reporting and appropriate assessment; symptoms are not a reliable exposure meter.

Which source controls and checks change the outcome?

Avoid the vibrating operation where possible, choose a lower-vibration tool or smoother transport method, and engineer suitable handles, seating or routes. The manager verifies actual use and relevant exposure assessment; a catalogue figure or a timer alone is insufficient. Maintain tools and surfaces, plan work and provide instruction and applicable health surveillance. Stop when a tool, seat or route defect invalidates the assessment; ordinary gloves are not a replacement for controlling vibration.

How should the controls be applied?

Choose suitable lower vibration methods, maintain tools and vehicles, improve travel surfaces, organise work and assess exposure. Match surveillance or symptom monitoring arrangements to the relevant exposure. For vehicles, review seat suitability and travel demand rather than relying only on shorter driving time.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. INDG175 supports hand arm vibration; the Health and Safety Executive (HSE) whole body route supports vehicle exposure decisions. Obtain actual equipment and exposure evidence. Stop using damaged equipment and escalate symptoms appropriately.

How can heat and cold make physical work unsafe?

Thermal conditions can impair performance and cause acute illness or contact injury. Workload, humidity, clothing, radiant heat, acclimatisation and individual needs change risk. See Temperature and Safe use of work equipment.

A foundry worker faces radiant heat, a kitchen worker heat and humidity, and a cold-store picker low temperatures plus manual effort. Heat exchange depends on workload, clothing, airflow and recovery as well as temperature. Reduced concentration, loss of dexterity or distress can then lead to another accident; a general room-temperature reading may miss the real exposure.

Which source controls and checks change the outcome?

Remove unnecessary exposure or change timing and process; provide suitable shielding, ventilation, cooled or heated recovery areas and handling design. The supervisor checks the task and workers under actual demand, allowing appropriate recovery and access to fluids or warming arrangements. Protective clothing must suit the exposure without creating another heat or entanglement risk. Stop and obtain help for signs of illness or failure of essential environmental controls.

How should the controls be applied?

Reduce exposure by process design, scheduling, shelter, ventilation and appropriate work and recovery arrangements. Consider contact protection and access to welfare.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Use actual conditions and task demands rather than a universal air temperature cut off. Suspected heat or cold illness requires the emergency and medical pathway, not chatbot diagnosis.

How do different radiation sources affect the control decision?

Ionising radiation, ultraviolet light, lasers and other non ionising sources involve different exposure mechanisms and control regimes. The source, wavelength or type, access and exposure geometry matter. See Radiation.

Industrial radiography, ultraviolet curing, welding arcs and lasers involve different sources and exposure routes. An unprotected eye or skin can be exposed when a shield is removed or a nearby person enters the work area; some sources can produce effects without an immediate sensation. The source identity, operating mode and access arrangement determine the specialist controls.

Which source controls and checks change the outcome?

Avoid or substitute the source where feasible, then use competent source-specific shielding, enclosures and access controls. Managers require the relevant specialist assessment and authorisation; distance, eyewear or a generic screen must not be guessed. Check interlocks, barriers and warning arrangements within authorised competence. Stop on a missing source identity, damaged shield or unexpected access; task-specific Personal protective equipment (PPE) supplements the design and does not establish a safe exposure by itself.

How should the controls be applied?

Identify the source and applicable regime, restrict exposure through design and access controls, and use appropriate specialist advice. Shielding and protective equipment must match the specific source.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Do not infer dose or safety from a source label. Obtain relevant competent radiation advice and current specific guidance before work.

How can poor lighting turn a routine movement into an incident?

Poor illumination or glare can hide steps, people, moving vehicles and defects. Task lighting and emergency lighting serve different needs. See Lighting and Workplace transport.

A driver reverses through glare at a yard entrance while a worker reads a small label in a dim plant room. Shadows, transition from bright to dark, obstruction and failure of a light can conceal a person, step or control setting. The result can be a collision, fall or mistaken operation rather than an injury caused by the light itself.

Which source controls and checks change the outcome?

Redesign the route or relocate the task to remove difficult visual conditions; provide suitable lighting and reduce glare at the actual working position. The supervisor checks visibility with vehicles, loads and equipment in place, not only with an empty room. Maintenance and emergency lighting arrangements support the design. Stop a movement or critical task if people, edges or controls cannot be reliably seen; high-visibility clothing is not a substitute for separation and usable lighting.

How should the controls be applied?

Design suitable lighting for routes and tasks, manage glare and shadows, maintain fixtures and consider loss of normal power.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Walk routes at the actual shift time and from driver and pedestrian positions. Do not use lighting to compensate for unsegregated transport routes.

Why can entering a confined space become immediately dangerous?

A substantially enclosed location can create specified dangers such as toxic atmosphere, oxygen deficiency, fire, engulfment or heat. Not every small room is legally a confined space; open pits can still qualify. See Safe work in confined spaces.

A tank, chamber or restricted process space may contain toxic gas, oxygen deficiency, engulfment or another specified serious risk. Cleaning, sludge disturbance or introducing a substance can change the atmosphere after entry starts. A colleague attempting an unplanned rescue can be exposed to the same hazard; an opening or a familiar location does not prove safe conditions.

Which source controls and checks change the outcome?

Avoid entry through external cleaning or inspection where possible. If entry remains necessary, competent people assess the actual hazards, isolation, atmosphere, access and rescue before authorising a suitable system. Conditions must remain controlled during work; a permit, smell or one reading does not guarantee safety. Stop on any lost control or uncertainty and use the planned response. Never enter to investigate or rescue without the required competence, equipment and arrangements.

How should the controls be applied?

Avoid entry wherever possible. Where unavoidable, use a competent planned safe system with relevant isolation, atmospheric controls, communication and rescue arrangements.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Do not authorise entry from a generic checklist or a single gas reading. Rescue needs suitable personnel and equipment; do not rely solely on emergency services arriving.

How can pressure, vacuum and trapped energy cause harm?

Pressure release can cause blast, projectiles and injection injuries. Vacuum can create collapse and other specialist system risks; the same controls are not automatically transferable. See Pressure systems and The safe isolation of plant and equipment.

A fitter opens a line thought to be empty; a vessel fails; a vacuum system implodes. Pressure differences can eject material, drive components or release hot or harmful contents, while trapped pressure can remain after a gauge falls. The harm route may include impact, burns, injection or exposure as well as equipment failure.

Which source controls and checks change the outcome?

Avoid unnecessary stored energy or select a safer process, then provide competently designed pressure containment and protective arrangements. An authorised maintainer uses the task-specific isolation and verification plan before access, including trapped volumes and connected systems. Keep people outside the release path and monitor relevant condition evidence. Do not crack a fitting to test whether pressure remains or improvise a relief setting; uncertainty, damage or unexpected pressure requires a stop and specialist decision.

How should the controls be applied?

Identify the system and contents, integrity and protective devices. Use competent examination and maintenance arrangements where applicable, isolate and control stored energy before intervention.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Confirm depressurisation and the safe isolation method with competent personnel. Do not invent safe pressure ratings, examination periods or vessel designs.

How do sharps, flying particles and moving objects cause injury?

Sharp edges, broken materials and projected debris can injure skin and eyes. Moving vehicles, swinging loads and displaced materials can strike people. A contaminated sharp also requires a biological exposure assessment. See Safe use of work equipment and Workplace transport.

A sharp edge cuts a packer, a chip reaches a bystander during machining, or a moving pallet strikes a pedestrian. The immediate tissue injury can be followed by contamination or a secondary fall. The injury route differs between a stationary edge, an ejected particle and a moving load, so one generic glove entry does not control all three.

Which source controls and checks change the outcome?

Remove sharp edges or redesign handling; contain particles at the source and separate moving loads from people. The task owner verifies guards, screens, load restraint and routes before starting and when conditions change. Suitable eye, face or hand protection is selected for the residual exposure and machinery compatibility; gloves can introduce entanglement risk around rotating parts. Stop if containment, visibility or separation fails and quarantine defective equipment.

How should the controls be applied?

Design out sharp handling, guard or contain ejection, provide suitable handling methods and segregate transport. Select supplementary protection for the actual task.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Check the ejection and travel paths and include cleaners and maintainers. Refer needlestick exposures promptly to the agreed clinical response pathway.

How can a water-side activity lead to drowning?

Falls into water or liquid can lead to drowning, entrapment or exposure to contaminated liquid. Depth, flow, temperature, access and rescue difficulty affect consequences. See Health and safety in agriculture and Managing health and safety in construction.

A lone maintenance worker slips beside a reservoir, an agricultural worker enters slurry-contaminated water, or a crew loses footing at a quay. Cold, depth, current, clothing and the ability to reach safety alter the outcome after immersion. A person who can swim can still become incapacitated, and an improvised rescue can expose additional people.

Which source controls and checks change the outcome?

Avoid water-side access where possible and use suitable working platforms, barriers or remote methods. A competent plan determines access, flotation where required, communication and rescue without relying on unplanned entry. Supervisors verify edge protection and changing water or weather conditions, then restrict work if the assessed arrangement is lost. Keep rescue equipment and trained response appropriate to the location; a buoyancy aid does not remove the fall or immersion hazard.

How should the controls be applied?

Avoid or separate access, provide suitable edge arrangements and plan work and rescue with competent personnel. Account for lone work and changes in water level.

When should work stop or be escalated?

Hold the affected activity if a critical safeguard is missing, fails its check or no longer matches the assessed conditions. Do not assume swimming ability or a flotation device makes entry safe. Agricultural guidance is contextual, not an approval of maritime or diving operations.

How should this hazard group be assessed and managed in practice?

For a warehouse receiving operation, walk the vehicle and pedestrian routes with workers. Check unloading at height, falling loads, flooring, visibility, noise and vibration. Include maintenance, abnormal conditions and work near water where relevant. Prioritise layout and segregation, stable access and collective fall protection. Select quieter and lower vibration equipment, maintain lighting, assess thermal conditions and plan confined space avoidance and rescue. Refer pressure systems and radiation to competent specialists. Route plan and inspection records; height work plan; exposure assessments; equipment maintenance; pressure examination records where required; confined space authorisation and rescue arrangements. Follow the assessment through procurement, implementation, briefing, supervision and verification rather than stopping at a document. See Preventing slips and trips at work and Working at height.

Agree the activity, affected people and prerequisites with operations, workers and any contractor before work. Test whether the task can be removed or redesigned, then verify selected controls in the place they will operate. During work, the supervisor compares conditions with the assessed method and has authority to stop. Completion includes safe waste or equipment handling, outstanding defects and a named hand-back decision; a completed risk form is not the end of the control process.

What must be established before assigning a risk score?

Identify the actual activity, foreseeable harm, people exposed and controls already demonstrated to work. Consider start up, normal operation, cleaning, maintenance, breakdown, emergency response and simultaneous work. A numerical matrix may support prioritisation but cannot establish compliance or replace a specialist assessment. Do not assign a residual risk score merely because a proposed control has been written into a form. Keep unknowns explicit and obtain site evidence before deciding that work can proceed. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).

Write a short causal description: the work creates or releases something, a person is exposed by a particular route, and a specified injury or ill-health outcome is foreseeable. Establish whether existing measures work in the actual task before estimating likelihood. An unknown material, unverified safe state or absent critical control is a decision gap, not a reason to select a reassuring number. The responsible manager records what must be resolved and who can authorise the next step.

Who owns each control and how should it be verified?

The dutyholder provides resources and arrangements. The operational manager assigns each control to someone able to implement it. Supervisors verify the controls at the point of work and respond to defects. Workers and representatives explain work as done and report problems. Specialist advisers address limits of local competence. Record the control, responsible role, evidence, check method, due date and escalation route. Completion of a training course or signature alone does not demonstrate effective risk control. See Managing for health and safety (HSG65).

Separate the person who funds and owns the control from the person who performs its check. For an engineered measure, record the accepted performance or condition, who verifies it, what a failed result means and how maintenance is coordinated. For a staffing or organisational measure, check actual cover, authority and staff experience. A signature confirms a recorded action, not effectiveness. The supervisor must be able to hold work and obtain a competent remedy when the required condition is not met.

Who might be affected, including people outside the work team?

Include employees, agency workers, apprentices, contractors, cleaners, maintainers, delivery drivers, service users, visitors and nearby public. Consider inexperience, pregnancy, disability, health conditions, language needs and lone work individually and without stereotyping. Consultation should identify barriers to controls rather than collect unnecessary medical details. Share relevant interface information between employers. A single activity may require several hazard groups; avoid splitting the assessment so that interacting controls have no clear owner. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).

Walk through the job from the perspective of someone who has not received the operator briefing: a cleaner, visiting driver, contractor, new starter or occupant of an adjoining area. Ask whether a control protects them during arrival, normal work, waste removal and emergencies. Agree who controls each shared boundary and how changes are communicated. Individual needs influence a suitable arrangement but do not justify treating an employee, disability or health condition as the hazard.

When should the assessment be reviewed and what evidence matters?

Reassess when equipment, materials, staffing, layout, working hours or environmental conditions change; after incidents, near misses, complaints, symptoms or evidence of failed controls; and through planned risk based review. Verify improvements under realistic demand, not only during an announced inspection. Retain dated observations, measurements where relevant, maintenance records and action closure evidence. No single review interval suits every risk. Health surveillance, exposure monitoring and clinical diagnosis are different activities and require their own competent arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).

Use a change or failure to test the original assumptions, not merely change the date on the form. A different product, higher throughput, altered route, new shift or contractor may change the harm pathway. Keep observations, applicable measurements, defects and authorisation evidence linked to the task. After correction, verify under representative demand and with affected workers. Repeated workarounds or symptoms require investigation of the design and organisation, even when no injury has been recorded.

How could physical hazards arise in construction and civil engineering?

In construction and civil engineering, roof refurbishment exposes contractors and people below to falls and dropped materials. Avoid fragile surface access and separate the work zone. Access plan and protection inspection. This is an illustrative application, not a documented case or a complete method statement. See Working at height.

Sequence the job with adjacent trades, delivery routes and the changing work area; the contractor supervisor must check the actual stage before releasing work. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in manufacturing and engineering?

In manufacturing and engineering, press operators experience impact noise and projected scrap. Contain ejection and reduce source noise before PPE. Noise assessment and guarding records. This is an illustrative application, not a documented case or a complete method statement. See Noise at work: A brief guide to controlling the risks and Safe use of work equipment.

Include startup, product change, cleaning and maintenance as well as the normal cycle; the production supervisor and maintainer agree who can stop and hand back the equipment. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in warehousing and logistics?

In warehousing and logistics, unloading vehicles exposes pedestrians to reversing movements and dock edges. Separate routes and organise stable unloading positions. Route observation and dock checks. This is an illustrative application, not a documented case or a complete method statement. See Workplace transport and Working at height.

Assess peak demand, vehicles, loads and visiting drivers together; the shift manager verifies separation and handling arrangements before releasing the route. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in agriculture and forestry?

In agriculture and forestry, forestry workers use vibrating tools on uneven ground. Select suitable tools and assess exposure and footing together. Tool maintenance and exposure records. This is an illustrative application, not a documented case or a complete method statement. See Hand-arm vibration at work: A brief guide and Preventing slips and trips at work.

Consider seasonal work, lone locations, animals, terrain and access to help; the task manager verifies the method and communication before the crew starts. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in healthcare and social care?

In healthcare and social care, hospital cleaners leave wet public corridors. Plan cleaning zones with a safe alternative route. Cleaning handover and floor defect records. This is an illustrative application, not a documented case or a complete method statement. See Preventing slips and trips at work.

Account for the person receiving care, infection control, dignity and changing assistance needs; the service manager coordinates the individual and task arrangements. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in hospitality and food production?

In hospitality and food production, kitchen staff work around hot appliances and spilled oils. Control heat and spills with suitable layout and cleaning. Thermal task review and route checks. This is an illustrative application, not a documented case or a complete method statement. See Temperature and Preventing slips and trips at work.

Check food operations, cleaning, public access and busy service periods together; the kitchen or service supervisor must be able to interrupt the task without leaving another exposure uncontrolled. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in retail and public services?

In retail and public services, shop employees handle deliveries beside customers. Separate delivery movements and secure stored loads. Delivery observation and storage checks. This is an illustrative application, not a documented case or a complete method statement. See Workplace transport and Managing risks and risk assessment at work.

Include customers, visitors and staff who arrive without the task briefing; the premises manager verifies access and a safe service alternative before the activity starts. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in offices and professional services?

In offices and professional services, office maintenance uses access equipment above occupied desks. Plan suitable access and separate people below. Access assessment and equipment checks. This is an illustrative application, not a documented case or a complete method statement. See Working at height.

Include contractors, hybrid working and occupied-space interfaces; the facilities or team manager checks the actual setup and how problems are reported. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in education and laboratories?

In education and laboratories, teaching laboratories use radiation sources. Use source specific controls and competent radiation advice. Source register and authorised procedures. This is an illustrative application, not a documented case or a complete method statement. See Radiation.

Separate learner awareness from authorised operation and specialist intervention; the responsible teacher, technician or laboratory manager checks material identity and supervision. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in utilities and waste management?

In utilities and waste management, utility workers inspect pits with atmospheric danger. Avoid entry or use a competent confined space system. Isolation and rescue readiness records. This is an illustrative application, not a documented case or a complete method statement. See Safe work in confined spaces.

Plan for unknown material, remote access and interfaces with the public or other operators; the supervisor holds the job until necessary identification and control evidence is available. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in energy and process industries?

In energy and process industries, process maintenance opens pressurised lines. Use planned isolation and verify pressure control. Isolation evidence and system integrity records. This is an illustrative application, not a documented case or a complete method statement. See The safe isolation of plant and equipment and Pressure systems.

Manage plant state, material change, connected systems and maintenance through competent process arrangements; the shift authority checks prerequisites and controls hand-back. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How could physical hazards arise in events and transport operations?

In events and transport operations, event crews rig equipment outdoors in changing weather. Coordinate height access falling objects and weather review. Rigging plan and pre use protection checks. This is an illustrative application, not a documented case or a complete method statement. See Working at height and Temperature.

Consider temporary equipment, weather, crowds, routes and limited setup time; the coordinator verifies the current layout and a workable stop or closure route. The assessment must test the stronger source-control option, then verify the remaining safeguards under representative demand. Hold the affected activity if a critical control fails or conditions no longer match the plan; the responsible competent person determines correction and release. Keep the task observation, decision, check and hand-back evidence, not just a course attendance record.

How do you put the controls into practice?

High-pressure fluid injection needs immediate treatment

A suspected fluid-injection injury needs immediate professional medical treatment, even if the wound looks small. Tell the treating team that high-pressure injection may have occurred and identify the fluid if known. Do not touch a pressurised leak or attempt self-treatment.

HSE: Hydraulic injection injury safety alert

Move from recognising harm to deciding, implementing, checking and improving the controls. Give each critical control an owner, a check method and a clear escalation route. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).

From work activity to verified control
  1. Understand the taskObserve people, equipment, materials and interfaces.
  2. Describe the harmIdentify exposure, energy release and foreseeable failure.
  3. Control at sourceAvoid, redesign, substitute, contain or separate the hazard.
  4. Check in real workVerify performance, defects, ownership and change triggers.
StageActionWho actsEvidence to retain
Before workConfirm the actual task, people, equipment, substances, location and abnormal conditions.Operational manager with competent adviceAssessment, observations, consultation and required specialist checks
Control deliveryPrioritise layout and segregation, stable access and collective fall protection. Select quieter and lower vibration equipment, maintain lighting, assess thermal conditions and plan confined space avoidance and rescue. Refer pressure systems and radiation to competent specialists.Responsible manager and authorised implementersRoute plan and inspection records; height work plan; exposure assessments; equipment maintenance; pressure examination records where required; confined space authorisation and rescue arrangements.
During workSupervise the real activity; check that critical controls remain effective and workers can report problems.Supervisor and workersChecks, defects, changes and escalations
Stop and restartStop the affected activity when serious danger or a failed critical control is suspected. Restart only through the competent site authorisation arrangements.Supervisor and authorised competent personReason for stopping, corrective action, verification and restart authority
ReviewRevisit controls after change, incidents, near misses, symptoms or repeated defects. Check effectiveness rather than counting completed forms.Manager, Occupational safety and health (OSH) adviser and worker representativesDated review, closure evidence and lessons for design and procurement

How does ERICPD apply to physical hazards?

ERICPD stands for Eliminate, Reduce, Isolate, Control, PPE and Discipline. For physical hazards, start by removing the hazardous task or source where practicable, then reduce and separate the remaining exposure. Combine suitable safeguards and work arrangements, use relevant personal protective equipment for residual risks, and keep all selected measures effective in everyday work. See HSE: Managing risk using PPE and Managing for health and safety (HSG65).

ERICPD: six decisions for selecting and sustaining controls
  1. 1 · E Eliminate

    Remove the hazardous task or source where practicable; confirm that the alternative still fulfils the task and assess remaining hazards.

  2. 2 · R Reduce

    Use a suitable less hazardous material, process or equipment, or reduce the hazard at source. Check any new risks introduced.

  3. 3 · I Isolate

    Separate people from the hazard through suitable containment, guarding, barriers or other task-specific separation.

  4. 4 · C Control

    Put remaining safeguards and workable task arrangements in place. Engineering controls and administrative arrangements have different strengths.

  5. 5 · P PPE

    Select personal protective equipment for relevant residual exposure. Check suitability, fit, compatibility, use and maintenance.

  6. 6 · D Discipline

    Sustain the controls through management support, supervision, maintenance and learning. Resolve workarounds and failures without blaming workers.

Eliminate, Reduce and Isolate focus attention on the hazard and the exposure pathway before reliance on behaviour or PPE. Controls usually work together: an enclosure may still need safe access, maintenance and instruction. Record the reasons for choosing or rejecting stronger options and check the complete task, including cleaning, maintenance and foreseeable changes.

ERICPD is a practical learning mnemonic. The five-level hierarchy is elimination, substitution, engineering controls, administrative controls and PPE. Reduce may include substitution or source reduction; Isolate commonly involves engineering. Control can include engineering and administrative measures. Discipline supports every selected level and is not an additional protective barrier. These frameworks are related; their labels do not form identical statutory ladders.

What does each role need to know and demonstrate?

People need learning and demonstrated competence for the decisions they actually make, not the same course at every organisational level. See Preventing slips and trips at work and Working at height.

For physical hazards, frontline learning must enable staff to recognise unsafe routes, access, energy and exposure. Supervisors need to check separation, access and the relevant exposure controls. Design, procurement and specialist assessment require deeper competence in access design, equipment selection and exposure assessment. Awareness, supervised practice, assessment and authorisation are different stages; an attendance record alone does not establish competence or permit specialist intervention.

Assess practical understanding with the actual task and credible abnormal conditions. The assessor must be competent for the scope being tested; authorisation should state its boundaries. Reassess after a material change, a defect, a demonstrated gap or work outside that scope rather than assuming one fixed refresher interval suits every role.

RoleLearning and decisionsAssessment, evidence and reassessment
Nearby staff and new startersRecognise the relevant exposure, usable routes, warning signs and reporting or emergency arrangements.Supervisor checks a practical explanation and scenario response; retain briefing scope and gaps. Repeat when routes or conditions change.
Frontline usersDemonstrate how to recognise unsafe routes, access, energy and exposure, including the checks, limits and stop decision.Competent task assessor observes representative practice and a defect scenario; record task, equipment/material scope and authorisation. Reassess for changed methods or performance gaps.
Specialist workers and maintainersDemonstrate the applicable technical method, safe state, interface controls and hand-back; do not infer specialist skill from general awareness.Competent specialist assesses work within a defined scope; retain method, assessment and authorisation evidence. New equipment, material or fault type may need a new decision.
Supervisors and coordinatorsDemonstrate how to check separation, access and the relevant exposure controls, manage a changed condition and hold or release work.Manager or competent reviewer tests a realistic planning and stop/restart scenario; retain observed decisions and corrective actions. Review following interface failures.
Managers, purchasers and designersMake and resource decisions on access design, equipment selection and exposure assessment, including the stronger-control options and residual risks.Competent review of specifications, trials, procurement acceptance and effectiveness evidence; record decision owner and outstanding actions. Reassess after process or organisational change.
OSH advisers, technical specialists and auditorsDistinguish jurisdiction and source limits, test representative evidence and recognise the boundary of their competence.Appropriately competent review of the actual assessment, sources, sampling and closed actions; retain scope and limitations. Escalate missing technical information rather than inventing a conclusion.

How can the hierarchy of controls reduce exposure to harmful physical agents?

A metal workshop uses a noisy cutting process beside assembly benches. Operators and nearby staff may be exposed to sound that can damage hearing. Consider the cutting task, neighbouring work and maintenance together.

Illustrative SHARE example: assess stronger options first, then combine the measures needed for the remaining task. If elimination removes the task entirely, later measures address only remaining or different hazards. Each stage below explains what changes, how harm is reduced and who verifies it.

Applying ERICPD to other hazards in this group

The same reasoning applies to other physical hazards: avoid work at height through ground-level methods, reduce vibration through process and tool selection, and separate pedestrians from vehicles. Match the controls to the particular energy or exposure; hearing protection does not control vibration or falling objects.

Keep an assessment record of the chosen controls, reasons for the selection, action owner, verification evidence and failure response. A failed critical control requires the affected activity to be held and corrected through the competent site arrangements; PPE or a completed form does not override that decision.

Guidance supporting these teaching examples

How would a noisy fabrication task be managed during a maintenance change?

Manage this activity by preventing exposure at source, coordinating the affected people and verifying the planned controls before release. A fabrication shop introduces a portable tool while a fixed machine is repaired. The operator, nearby assemblers and a maintenance contractor encounter noise, vibration, particles and changed access. The harm can include immediate eye injury and hearing or vibration-related ill health developing with repeated exposure. See Noise at work: A brief guide to controlling the risks and Hand-arm vibration at work: A brief guide.

Illustrative SHARE workplace example

What must be agreed before work starts?

The production manager asks whether the work can be deferred, bought in or performed by a quieter and lower-vibration method. A competent assessor evaluates the selected method under representative use, including tool condition, grip, duration and nearby people. Designed containment and separation precede task scheduling and compatible residual protection. The supervisor confirms tooling, guards, workpiece restraint and routes before authorisation.

What changes, stops or hand-back decisions matter?

During the task, unexpected vibration, failed containment or inability to hear a critical warning causes a stop and reassessment. A replacement tool is not automatically equivalent. After the job, record use, defects and the relevant control evidence; review feedback and any appropriate health surveillance through competent arrangements. Restart normal production only after the maintainer and supervisor complete the hand-back. No invented exposure limit or universal tool-use time is assumed.

How should jurisdiction, local rules and management assurance be handled?

Apply the law and regulator guidance for the work location, then use competent task and equipment information to establish the practical arrangements. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).

HSE guidance generally addresses Great Britain; Northern Ireland has its own instruments and Health and Safety Executive for Northern Ireland (HSENI) route. Construction, dangerous substances, equipment and other specialist topics need the applicable instrument, not a Great Britain (GB) duty copied into a Northern Ireland (NI) answer. Fire arrangements also differ across the United Kingdom (UK) nations. Foreign project examples require destination-specific official advice and competent local assessment.

Distinguish a legal duty, regulator guidance, an organisation's rule and an illustrative SHARE method. A management system can link assessment, procurement, competence, maintenance, consultation and corrective action; a certification label or an unverified standard clause does not authorise work. For this group, sample evidence on access design, equipment selection and exposure assessment and compare the recorded method with the activity observed on site. Resolve conflicts or missing technical information with the responsible competent person.

How would keeping a retail entrance open during cleaning work in practice?

Cleaners and customers share a tiled entrance. Water and cleaning residue can reduce grip; a slip can cause a fall and a serious injury. The supervisor first considers cleaning outside opening hours or maintaining a separate dry route, rather than putting a sign beside an uncontrolled wet surface. See Preventing slips and trips at work.

Illustrative SHARE workplace example

What is required before and during the activity?

Before cleaning, agree the usable pedestrian route, accessibility and emergency escape, position effective separation and confirm the drying method. During the task, check that customers cannot enter the affected area and that spills do not extend beyond it. Stop and correct the arrangement if barriers move, the dry route becomes wet or safe access cannot be maintained.

What does safe completion and hand-back require?

Reopen only after the supervisor verifies a safe surface and route. Retain the method, checks and defect actions; investigate repeat contamination or drainage problems. A warehouse variation needs coordination with vehicles and load handling, not just the same cleaning notice.

Acronyms and terms

These terms distinguish the source of harm, the exposure route and the controls needed for the actual work.

Letters or termExpansion or definitionMeaning in this topic
UKUnited KingdomA geographical description, not one identical set of health-and-safety instruments.
GBGreat BritainEngland, Scotland and Wales; HSE guidance is generally framed for this jurisdiction.
NINorthern IrelandA separate health-and-safety legal route overseen by HSENI.
HSEHealth and Safety ExecutiveThe GB regulator and a publisher of official workplace guidance.
HSENIHealth and Safety Executive for Northern IrelandThe NI regulator; check its applicable requirements and advice.
OSHOccupational safety and healthPreventing work-related injury and ill health.
PPEPersonal protective equipmentEquipment worn for remaining exposure; it does not replace stronger source controls.
Control of Substances Hazardous to Health (COSHH)Control of Substances Hazardous to HealthThe GB hazardous-substance assessment and exposure-control route.
CDMConstruction (Design and Management)Construction duty and coordination arrangements; check the applicable GB or NI instrument.
PUWERProvision and Use of Work Equipment RegulationsGB requirements for suitable work equipment, protection and competent use.
ERICPDEliminate, Reduce, Isolate, Control, PPE, DisciplineA learning mnemonic for selecting and sustaining controls; not a statutory ladder.
HazardA source or condition with potential for harmDescribe what creates harm, rather than calling a person the hazard.
ExposureA route or contact connecting source and personConsider dose, duration and circumstances where relevant.
Critical controlA measure essential to the safe arrangementDefine its required condition, check, owner and failure response.
Hand-backControlled return to operation or useConfirm people, equipment, protection and outstanding conditions before release.

Example handy documents

Useful records connect the actual task to control ownership, checks, stop decisions and verified hand-back. See Managing risks and risk assessment at work and Managing for health and safety (HSG65).

The following are examples of documents an organisation could create or adapt, not downloadable files or a complete safe system. Use the task-specific information and competent review before applying them. Keep private health information outside general operational records.

What should a task and harm-route assessment contain?

Record people, source, exposure or energy, foreseeable harm, existing controls, stronger options, residual uncertainty and the responsible decision owner.

What should a critical-control check and defect log contain?

Record the required condition, check method, responsible person, failed result, restricted work and verified corrective action.

What should a change and hand-back record contain?

Capture changed material, equipment, staffing, layout or conditions; prerequisites, hold decisions, competent verification and restart authority.

What should a competence and authorisation record contain?

Name the assessed task and scope, practical evidence, assessor, limits, supervision and reassessment triggers.

What should an operational learning review contain?

Link observations, complaints, near misses or relevant exposure evidence to a design or organisational change and an effectiveness check.

Documents to download

Download editable resources from the SHAREhub environment to support your work. Working forms and spreadsheet input areas are blank. Reports, plans, guides, briefings, procedures and policies contain completed worked example content to adapt.

Return to SHARE home